INSTRUCTION MANUAL Ultra-slim Body NA1-5 Series Panasonic Thank you very much for Purchasing Panasonic prod- ucts. Read this Instruction Manual carefully and thor- oughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference. Z\ WARNING each region or country. Health, Labor and Welfare of Japan. @ If this product is used as a sensing device for personnel protection, serious body injury or death could result. @ Never use this product as a sensing device with any press machine, shearing machine, roll grinding machine, forming machine, vulcanizer, or robot etc. for protection of a hand or a part of the body. @ This product does not include a self-checking circuit for safety functions necessary to allow its use as a safety device. Thus, a system failure or malfunction can result in either an energized or a de-energized output condition. @ When this product is used as a sensing device in the following applications and if a problem relating to law or product liability' occurs, Our company shall not be liable for the failure and for the damage or less. 1) Use of this product installed to a machinery or a device as a sensing device to detect a hand or a part of the operator's body entering a dangerous area and stop the machinery or the device. 2) Installation of this product to a protection device for preventing to enter a dangerous area and use of this as a sensing device which detects a hand or a part of the operator's body and open / close the door or window. 3) Use of this product as a sensing device for personnel protection (including interlock). @ For sensing devices to be used as safety devices for press machines or for personnel protection, use products which meet standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in @ In case of using as a safety device for press machines in Japan, use a product approved by the Ministry of El SPECIFICATIONS E] MOUNTING @ Use M4 screws with washers, and M4 nuts. The tightening torque should be 0.5N-m or less. (Please arrange the screws and nuts separately.) M4 nuts L @ Optional sensor mounting brackets (MS-NA1-1, MS-NA2-1) are also available. Z3V/O CIRCUIT DIAGRAMS @ NPN output type M4 screws with washers Color code / Connector pin No. of the pigtailed type | (Brown 41) +V (Black / 4) Output L \(Note 1) +_L12to 24v Dc CK #2 | ToomAmax. ~ | 71% {Blue / 3) OV 40 Sensor circuit Type Long sensing range High-luminous job indicator NPN output type PNP output type NPN output type PNP output type Item Model No. (Note 1) NA1-5 NA1-5-PN NA1-PK5 NA1-PK5-PN Sensing height 100mm Sensing range (Note 2) 0.2 to 3m (0.05 to 1m when set to SHORT) | 0.1 to 1.2m (0.05 to 0.5m when set to SHORT) Beam pitch 25mm Number of beam channels 5 beam channels Sensing object 35mm or more opaque object Supply voltage 12 to 24V DC+10% Ripple P-P 10% or less Emitter: 0.5W or less Power consumption (Note 3} Receiver: 0.8W or less Emitter: 0.6W or less Receiver: 0.9W or less Emitter: 0.5W or less Receiver: 0.8W or less Emitter: 0.6W or less Receiver: 0.9W or less <NPN output type> NPN open-collector transistor - Maximum sink current: 100mA <PNP output type> PNP open-collector transistor - Maximum source current: 100mA 7 : Internal circuit ~~ Users' circuit Notes: 1) The emitter is not incorporated with the output. 2) In order to use the job indicators as large size operation indicators, connect the job indicator input (pink) and output (black) wires together. Symbols...D : Reverse supply polarity protection diode Zp : Surge absorption zener diode Tr : NPN output transistor E : Job indicator 1 Cable 0.3mm? 4-core (emitter: 3-core) oil-resistant cabtyre cable, 2m long Weight (total of the emitter and the recelver) Emitter: 70g approx., Receiver: 80g approx. | Emitter: 80g approx., Receiver: 85g approx. Notes: 1) The model No. with suffix '-C5Ei PART DESCRIPTION Job indicator (Orange) Power indicator {Green) [a SELECTION @ Selection of output operation * The output operation mode is selected by the oper- ation mode switch on the receiver. Make sure that the power is off while setting. The operation mode does not change even if the setting is changed in the power supply on condi- Operation mode switch Job indicator (Orange) Stable incident beam indicator (Green) Operation indicator (Red) OF OPERATION BEAM AXIS ALIGNMENT @ Place the emitter and the receiver face to face along a straight line. @ After the cable has been correctly connected, switch the power ON. @ Move the emitter in the up, down, left and right di- rections, in order to determine the range of the beam received condition with the help of the oper- ation indicator (red) on the receiver. Then, set the emitter at the center of this range. @ Similarly, adjust for up, down, left and right angular movement of the emitter. Further, perform the angular adjustment for the re- ceiver also. Check that the stable incident beam indicator (green) lights up. @ Interrupt each beam channel with the actual sens- ing object, and confirm that the sensor operates correctly. Note: The stable incident beam indicator (green) lights up when all the five light beams are stably received by the receiver. tion. Operation mode switch Output operation | Operation indicator | V : ON when one or | Lights up when D-ON = more beams are | the output is w SINGLE | CH) DOUBLE} interrupted. ON. a D/ON | Cl Lon z V OFF when one or more beams | Lights up when L-ON = are interrupted. | the output is SINGLE | CH) DOUBLE (me when all bears OFF. D/ON [MEI L/ON I are received. V on wn more. y Lights up when D-ON = beams are inter- | the output is w SINGLE | HL] | DOUBLE ON. a p/on | Cll] Lon | upted. 5 9 V Qa OFF when any Lights up when L-ON = the output is = beams are inter- SINGLE | MC] | DOUBLE OFF. D/ON |MEI| Lon | rupted. Note: FREQ. A/ FREQ. B and LIGHT / FLASH selection switches are not related to the output operation selection. @ Job indicator operation selection * Lighting / blinking is selected by the operation mode switch on the emitter and the receiver. Make sure that the power is off while setting. The operation mode does not change even if the setting is changed in the power supply on condi- tion. Operation mode switch Job indicator . V Emitter ro LIGHT | Cl | FLASH Yd E a | oO Lighting +) Receiver V || LIGHT | Cl | FLASH Yd a | on Vv mitter = LIGHT | MIC] | FLASH x = < Blinking Receiver V || LIGHT | MIL] | FLASH | a | Note: FREQ. A/ FREQ. B, SINGLE / DOUBLE and LONG / SHORT selection switches are not related to the setting of job indicator. Stable incident beam indicator (Green) Operation indicator (Red) Ee] INTERFERENCE PREVENTION FUNCTION @ By setting different emission frequencies, two sets of sensors can be mounted close together, as shown in the figure below. a. I Sensor A Sensor B @ Frequency setting * Set the frequency of Sensor A to FREQ. A (on the emitter and the receiver) and that of Sensor B to FREQ. B (on the emitter and the receiver). Make sure that the power is off while setting. The operation mode does not change even if the setting is changed in the power supply on condi- tion. Operation made switch Emitter Receiver Sensor A FREQ. A FREQ.B | FREQ.A FREQ. B (FREQ. A) Sensor B FREQ. A FREQ.B | FREQ.A FREQ. B (FREQ. B) Note: LIGHT / FLASH, SINGLE / DOUBLE and D-ON / L-ON selec- tion switches are not related to the interference prevention function. [E] LONG / SHORT SELECTION SWITCH (incorporated in the emitter) @ Select the switch setting ac- Setting distance cording to the setting distance 9 *L~ L between the emitter and the receiver as given below. Emitter Receiver Make sure that the power is off while setting. The operation mode does not change even if the setting is changed in the power supply on condition. Setting distance L NA1-5(-PN) NA1-PK5(-PN) Operation more switch (Emitter) V LONG Fi SHORT V LONG a SHORT il) FIXING OF SENSOR MOUNTING BRACKET (OPTIONAL) @ Assembly diagram for MS-NA1-1 M4 screws with washers, nuts and hooks are at- tached with MS-NA1-1. 0.05 to im (0.05mSLS1m) 0.05 to 0.5m (0.05mSLS0.5m) SHORT 0.5 to 1.2m (0.5mSLS1.2m) 1 to 3m (imSLS3m) LONG Sensor mounting @ Assembly diagram for MS-NA2-1 M4 screws with washers, nuts, hooks and spacers are attached with MS-NA2-1. Sensor mounting bracket Front mounting Sensor mounting bracket Sensor Spacer [ll INTENDED PRODUCTS FOR CE MARKING CE @ The models listed under ' Hl SPECIFI- CATIONS' come with CE Marking. As for all other models, please contact our Office. @ Contact for CE <Until June 30 ,2013> Panasonic Electric Works Europe AG Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany <From July 1 ,2013> Panasonic Marketing Europe GmbH Panasonic Testing Center Winsbergring 15, 22525 Hamburg,Germany Panasonic Industrial Devices SUNX Co., Ltd. http://panasonic.net/id/pidsx/global Overseas Sales Division (Head Office) 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-568-33-7861 FAX: +81-568-33-8591 About our sale network, please visit our website. Panasonic Industrial Devices SUNX Co., Ltd. 2012 PRINTED IN CHINA