General Description
The MAX9140/MAX9141 are single and the MAX9142/
MAX9144 are dual/quad high-speed comparators optimized
for systems powered from a 3V or 5V supply. The MAX9141
features latch enable and device shutdown. These devices
combine high speed, low power, and rail-to-rail inputs.
Propagation delay is 40ns, while supply current is only
150μA per comparator.
The input common-mode range of the devices extends beyond
both power-supply rails. The outputs pull to within 0.3V of
either supply rail without external pullup circuitry, making these
devices ideal for interface with both CMOS and TTL logic. All
input and output pins can tolerate a continuous short-circuit
fault condition to either rail. Internal hysteresis ensures clean
output switching, even with slow-moving input signals.
The devices are higher-speed, lower-power, and lower-
cost upgrades to industry-standard comparators MAX941/
MAX942/MAX944.
The MAX9140 are offered in tiny 5-pin SC70 and SOT23
packages. The MAX9141 and MAX9142 are available in
8-pin SOT23 and SO packages, while the MAX9144 is
available in both 14-pin SO and TSSOP packages.
Applications
Line Receivers
Battery-Powered Systems
Threshold Detectors/Discriminators
3V/5V Systems
Zero-Crossing Detectors
Sampling Circuits
Features
Fast, 40ns Propagation Delay (10mV Overdrive)
Low Power
150μA Supply Current Per Comparator (3V)
Optimized for 3V and 5V Applications
Rail-to-Rail Input Voltage Range
Low, 500μV Offset Voltage
Internal Hysteresis for Clean Switching
Outputs Swing 300mV of Power Rails
CMOS/TTL-Compatible Outputs
Output Latch (MAX9141 Only)
Shutdown Function (MAX9141 Only)
Available in SC70 and SOT23 Packages
AEC-Q100 Qualified (MAX9140AAXK/V+T Only)
19-2064; Rev 8; 1/19
Click here for production status of specic part numbers.
1
2
3
4
8
7
6
5
N.C.
OUT
GND LE
SHDN
IN-
IN+
VCC VCC
VCC
SOT23/SO
1
2
3
4
8
7
6
5
OUTB
INB-
INB+
GND
INA+
INA-
OUTA
SOT23/SO
14
13
12
11
10
9
8
1
2
3
4
5
6
7
OUTD
IND-
IND+
GND
INA+
INA-
OUTA
INC+
INC-
OUTC
OUTB
INB-
INB+
TSSOP/SO
TOP VIEW
A
B
A D
B C
GND
IN-IN+
1 5 VCC
OUT
SC70/SOT23
2
3 4
MAX9142
MAX9141
MAX9144
MAX9140
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
Pin Congurations
Power-Supply Ranges
Supply Voltage (VCC to GND) ...........................................+6V
IN+, IN- to GND .................................... -0.3V to (VCC + 0.3V)
LE Input Voltage (MAX9141 only) ........ -0.3V to (VCC + 0.3V)
SHDN Input Voltage (MAX9141 only) .. -0.3V to (VCC + 0.3V)
Current into Input Pins .....................................................±20mA
Input/Output Short-Circuit Duration to
VCC or GND ..........................................................Continuous
Continuous Power Dissipation (TA = +70°C)
5-Pin SC70 (derate 3.1mW/°C above +70°C) .............247mW
5-Pin SOT23 (derate 7.1mW/°C above +70°C) ..........571mW
8-Pin SOT23 (derate 9.1mW/°C above +70°C) ..........727mW
8-Pin SO (derate 5.9mW/°C above +70°C) .............. 470.6mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) ........ 727mW
14-Pin SO (derate 8.33mW/°C above +70°C) .......... 666.7mW
Operating Temperature Range
E grade ........................................................... -40°C to +85°C
A grade ......................................................... -40°C to +125°C
Junction Temperature ...................................................... +150°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
(VCC = 5V, VCM = 0V, SHDN = LE = VCC (MAX9141 only), CL = 15pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA = +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Operating Supply Voltage VCC (Note 2) 2.7 5.5 V
Input Voltage Range VCMR (Note 3) -0.2 VCC +
0.2 V
Input O󰀨set Voltage VOS (Note 4)
TA = +25°C 0.5 2.0
mVTA = -40°C to +85°C 4.5
MAX9140AA_ _ 6.0
Input Hysteresis VHYST (Note 5) 1.5 mV
Input Bias Current IB(Note 6) TA = -40°C to +85°C 90 320 nA
MAX9140AA_ _ 350
Input O󰀨set Current IOS
TA = -40°C to +85°C 8 120 nA
MAX9140AA_ _ 140
Common-Mode Rejection Ratio CMRR VCC = 5.5V
(Note 7)
TA = -40°C to +85°C 80 800 µV/V
MAX9140AA_ _ 850
Power-Supply Rejection Ratio PSRR 2.7V ≤ VCC
5.5V
TA = -40°C to +85°C 80 750 µV/V
MAX9140AA_ _ 800
Output High Voltage VOH
ISOURCE =
4mA
TA = -40°C to +85°C VCC -
0.425
VCC -
0.3 V
MAX9140AA_ _ VCC - 0.47
Output Low Voltage VOL ISINK = 4mA TA = -40°C to +85°C 0.3 0.425 V
MAX9140AA_ _ 0.45
Output Leakage Current ILEAK SHDN = GND, MAX9141 only (Note 8) 0.04 1 µA
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
2
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VCC = 5V, VCM = 0V, SHDN = LE = VCC (MAX9141 only), CL = 15pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA = +25°C.) (Note 1)
Note 1: All devices are 100% production tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Note 2: Inferred from PSRR test.
Note 3: Inferred from CMRR test. Note also that either or both inputs can be driven to the absolute maximum limit (0.3V beyond
either supply rail) without damage or false output inversion.
Note 4: VOS is defined as the center of the input-referred hysteresis zone. See Figure 1.
Note 5: The input-referred trip points are the extremities of the differential input voltage required to make the comparator output
change state. The difference between the upper and lower trip points is equal to the width of the input-referred hysteresis
zone. See Figure 1.
Note 6: The polarity of IB reverses direction as VCM approaches either supply rail.
Note 7: Specified over the full common-mode voltage range (VCMR).
Note 8: Specification is for current flowing into or out of the output pin for VOUT driven to any voltage from VCC to GND while the part
is in shutdown.
Note 9: Specified between any two channels in the MAX9142/MAX9144.
Note 10: Specified as the difference between tPD+ and tPD- for any one comparator.
Note 11: Applies to the MAX9141 only for both SHDN and LE.
Note 12: Applies to the MAX9141 only. Comparator is active with LE driven high and is latched with LE driven low (VOD = 10mV). See
Figure 2.
Note 13: Applicable to the MAX9141 only. Comparator is active with the SHDN driven high and is shutdown with SHDN driven low.
Shutdown enable time is the delay when the SHDN is driven high to the time the output is valid. Shutdown disable time is the
delay when the SHDN is driven low to the time the comparator shuts down.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Supply Current (Per Comparator) ICC
VCM = VCC = 3V
MAX9141 165 275
µA
MAX9140,
TA = -40°C to 85°C 150 250
MAX9140AA_ _ 360
MAX9142/MAX9144 150 250
VCM = VCC = 5V
MAX9141 200 320
MAX9140,
TA = -40°C to 85°C 165 300
MAX9140AA_ _ 400
MAX9142/MAX9144 165 300
MAX9141 only, SHDN = GND;
VCC = VCM = 3V 12 30
Propagation Delay tPD+,
tPD-
VCC = 3V, VOD = 10mV 40 ns
Di󰀨erential Propagation Delay dtPD VOD = 10mV (Note 9) 2 ns
Propagation Delay Skew VOD = 10mV (Note 10) 2 ns
Logic Input-Voltage High VIH (Note 11) (VCC/2)
+0.4 VCC/2 V
Logic Input-Voltage Low VIL (Note 11) VCC/2 (VCC/2)
-0.4 V
Logic Input Current IIL, IIH VLOGIC = 0 to VCC (Note 11) 2 10 µA
Data-to-Latch Setup Time tS(Note 12) 16 ns
Latch-to-Data Hold Time tH(Note 12) 16 ns
Latch Pulse Width tLPW (Note 12) 45 ns
Latch Propagation Delay tLPD (Note 12) 60 ns
Shutdown Enable Time (Note 13) 1 µs
Shutdown Disable Time (Note 13) 5 µs
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
3
Electrical Characteristics (continued)
(VCC = 3.0V, VCM = 0V, CL = 15pF, VOD = 10mV, TA = +25°C, unless otherwise noted.)
320
322
326
324
328
330
-40 0-20 20 40 60 80 100
OUTPUT LOW VOLTAGE
vs. TEMPERATURE
MAX9140 TOC02
TEMPERATURE (°C)
VOL (mV)
ISINK = 4mA
5.00
5.05
5.10
5.15
5.20
-40 0-20 20 40 60 80 100
OUTPUT HIGH VOLTAGE
vs. TEMPERATURE
MAX9140 TOC03
TEMPERATURE (°C)
VOH (V)
ISOURCE = 4mA
VCC = 5.5V
35
40
45
50
-40 0-20 20 40 60 80 100
OUTPUT SHORT-CIRCUIT (SINK) CURRENT
vs. TEMPERATURE
MAX9140 TOC04
TEMPERATURE (°C)
OUTPUT SHORT-CIRCUIT SINK CURRENT (mA)
15
25
35
45
-40 0-20 20 40 60 80 100
OUTPUT SHORT-CIRCUIT (SOURCE)
CURRENT vs. TEMPERATURE
MAX9140 TOC05
TEMPERATURE (°C)
OUTPUT SHORT-CIRCUIT SOURCE CURRENT (mA)
0
100
50
200
150
250
300
3456
MAX9140 SUPPLY CURRENT
vs. SUPPLY VOLTAGE
MAX9140 toc01
VCC (V)
ICC (A)
TA = +85∞C
TA = +25∞C
TA = -40∞C
0
40
20
80
60
120
100
140
-50 0 25-25 50 75 100
INPUT BIAS CURRENT
vs. TEMPERATURE
MAX9140 toc06
TEMPERATURE (°C)
INPUT CURRENT (nA)
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
Maxim Integrated
4
www.maximintegrated.com
Typical Operating Characteristics
(VCC = 3.0V, VCM = 0V, CL = 15pF, VOD = 10mV, TA = +25°C, unless otherwise noted.)
-500
-200
-300
-400
-100
0
100
200
300
400
500
-50 0-25 25 50 75 100
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
MAX9140 toc07
TEMPERATURE (°C)
VOS (µV)
-1.0
-0.4
-0.6
-0.8
-0.2
0
0.2
0.4
0.6
0.8
1.0
-50 0-25 25 50 75 100
TRIP POINT
vs. TEMPERATURE
MAX9140 toc08
TEMPERATURE (°C)
VOS (mV)
VTRIP+
VTRIP-
-1
1
0
3
2
6
5
4
7
-40 0-20 20 40 60 80 100
INPUT VOLTAGE RANGE
vs. TEMPERATURE
MAX9140TOC09
TEMPERATURE (°C)
INPUT VOLTAGE RANGE (V)
VCMR+
VCMR-
VCC = 5.5V
20
25
35
30
40
45
0 4020 60 80 100
PROPAGATION DELAY
vs. INPUT OVERDRIVE
MAX9140 toc10
INPUT OVERDRIVE (mV)
PROPAGATION DELAY (nS)
tPD+
tPD-
25
30
40
35
45
50
-50 0-25 25 50 75 100
PROPAGATION DELAY
vs. TEMPERATURE
MAX9140 toc11
TEMPERATURE (°C)
PROPAGATION DELAY (ns)
tPD+
tPD-
20
30
25
40
35
50
45
55
15 45 6030 75 90 105
PROPAGATION DELAY
vs. CAPACITIVE LOAD
MAX9140 toc12
CAPACITIVE LOAD (pF)
PROPAGATION DELAY (ns)
tPD+
tPD-
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
Maxim Integrated
5
www.maximintegrated.com
Typical Operating Characteristics (continued)
(VCC = 3.0V, VCM = 0V, CL = 15pF, VOD = 10mV, TA = +25°C, unless otherwise noted.)
PIN NAME FUNCTION
MAX9140 MAX9141 MAX9142 MAX9144
1 1 OUTA Comparator A Output
2 2 INA- Comparator A Inverting Input
3 3 INA+ Comparator A Noninverting Input
5 1 8 4 VCC Positive Supply
5 5 INB+ Comparator B Noninverting Input
6 6 INB- Comparator B Inverting Input
7 7 OUTB Comparator B Output
8 OUTC Comparator C Output
9 INC- Comparator C Inverting Input
10 INC+ Comparator C Noninverting Input
2 4 4 11 GND Ground
12 IND+ Comparator D Noninverting Input
13 IND- Comparator D Inverting Input
14 OUTD Comparator D Output
3 2 IN+ Noninverting Input
4 3 IN- Inverting Input
6 SHDN Shutdown: MAX9141 is active when SHDN is driven high;
MAX9141 is in shutdown when SHDN is driven low.
5 LE The output is latched when LE is low. The latch is transparent
when LE is high.
1 7 OUT Comparator Output
8 N.C. No Connection. Not internally connected.
OUTPUT
2V/div
INPUT
50mV/div
PROPAGATION DELAY (tPD-)
MAX9140TOC13
10ns/div
VOD = 10mV
VCC = 5.5V
OUTPUT
2V/div
INPUT
50mV/div
PROPAGATION DELAY (tPD+)
MAX9140TOC14
10ns/div
VOD = 10mV
VCC = 5.5V
OUTPUT
2V/div
INPUT
50mV/div
SINUSOID RESPONSE AT 4MHz
MAX9140TOC15
50ns/div
VCC = 5.5V
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
6
Pin Description
Typical Operating Characteristics (continued)
Detailed Description
The MAX9140/MAX9141/MAX9142/MAX9144 single-
supply comparators feature internal hysteresis, high
speed, and low power. Their outputs are pulled to within
300mV of either supply rail without external pullup or
pulldown circuitry. Rail-to-rail input voltage range and low-
voltage single-supply operation make these devices ideal
for portable equipment. The devices interface directly to
CMOS and TTL logic.
Most high-speed comparators oscillate in the linear region
because of noise or undesired parasitic feedback. This
tends to occur when the voltage on one input is at or
equal to the voltage on the other input. To counter the
parasitic effects and noise, the devices have an internal
hysteresis of 1.5mV.
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling input
voltage (Figure 1). The difference between the trip points
is the hysteresis. The average of the trip points is the offset
voltage. When the comparator’s input voltages are equal,
the hysteresis effectively causes one comparator input
voltage to move quickly past the other, thus taking the
input out of the region where oscillation occurs. Standard
comparators require hysteresis to be added with external
resistors. The devices’ fixed internal hysteresis eliminates
these resistors. To increase hysteresis and noise margin
even more, add positive feedback with two resistors as a
voltage divider from the output to the noninverting input.
Figure 1 illustrates the case where IN- is fixed and IN+ is
varied. If the inputs were reversed, the figure would look
the same, except the output would be inverted.
The MAX9141 includes an internal latch that allows
storage of comparison results. The LE pin has a high input
impedance. If LE is high, the latch is transparent (i.e., the
comparator operates as though the latch is not present).
The comparator’s output state is latched when LEis pulled
low (Figure 2).
Shutdown Mode (MAX9141 Only)
The MAX9141 shuts down when the SHDN pin is low. When
shut down, the supply current drops to less than 12μA, and
the three-state output becomes high impedance. The SHDN
pin has a high-input impedance. Connect SHDN to VCC for
normal operation. Exit shutdown with LE high (transparent
state); otherwise, the output will be indeterminate.
Input Stage Circuitry
The devices include internal protection circuitry that prevents
damage to the precision input stage from large differential
input voltages. This protection circuitry consists of two
back-toback diodes between IN+ and IN- as well as two
series 4.1kΩ resistors (Figure 3). The diodes limit the
differential voltage applied to the internal circuitry of the
comparators to be no more than 2VF, where VF is the
forward voltage drop of the diode (about 0.7V at +25°C).
For a large differential input voltage (exceeding 2VF), this
protection circuitry increases the input bias current at IN+
(source) and IN- (sink).
F
(IN+ - IN-) - 2V
Input Current 2 4.1k
=
×Ω
Input current with large differential input voltages should
not be confused with input bias current (IB). As long as the
differential input voltage is less than 2VF, this input current
is equal to IB. The output is in the correct logic state if one
or both inputs are within the common-mode range.
Figure 1. Input and Output Waveform, Noninverting Input
Varied
VTRIP+
VHYST
VTRIP-
COMPARATOR
OUTPUT
VOH
VOL
VTRIP+ + VTRIP-
2
VOS =
VIN- = 0
VIN+
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
7
Output Stage Circuitry
The MAX9140/MAX9141/MAX9142/MAX9144 contain a
current-driven output stage as shown in Figure 4. During
an output transition, ISOURCE or ISINK is pushed or pulled
to the output pin. The output source or sink current is high
during the transition, creating a rapid slew rate. Once the
output voltage reaches VOH or VOL, the source or sink
current decreases to a small value, capable of maintaining
the VOH or VOL static condition. This significant decrease
in current conserves power after an output transition has
occurred.
One consequence of a current-driven output stage is a
linear dependence between the slew rate and the load
capacitance. A heavy capacitive load will slow down a voltage
output transition. This can be useful in noisesensitive
applications where fast edges may cause interference.
Applications Information
Circuit Layout and Bypassing
The high-gain bandwidth of the MAX9140/MAX9141/
MAX9142/MAX9144 requires design precautions to real-
ize the full high-speed capabilities of these comparators.
The recommended precautions are:
1) Use a PCB with a good, unbroken, low-inductance
ground plane.
2) Place a decoupling capacitor (a 0.1μF ceramic capacitor
is a good choice) as close to VCC as possible.
3) Pay close attention to the decoupling capacitor’s bandwidth,
keeping leads short.
4) On the inputs and outputs, keep lead lengths short to avoid
unwanted parasitic feedback around the comparators.
5) Solder the device directly to the PCB instead of using
a socket.
Figure 2. MAX9141 Timing Diagram with Latch Operator
Figure 3. Input Stage Circuitry
VOH
tLPW
OUT
tLPD
tPD
VCC
0
VCC
2
VCC
2
VOL
LE
DIFFERENTIAL
INPUT
VOLTAGE
VOS
VOD
tH
tS
4.1k
4.1k
TO INTERNAL
CIRCUITRY
TO INTERNAL
CIRCUITRY
IN–
IN+
MAX9140
MAX9141
MAX9142
MAX9144
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
8
Figure 4. Output Stage Circuitry Figure 5. 3.3V Digitally Controlled Threshold Detector
Figure 6. Line Receiver Application
ISOURCE
ISINK
VCC
GND
OUTPUT
MAX9140
MAX9141
MAX9142
MAX9144
ANALOG IN
VSS
SERIAL
DIGITAL
INPUT
VDD
SDI
DACOUTC
VDD = 3.3V
VREFC
8-BIT DAC
GND
MAX512
MAX9140
0
3V
CLEAN
DIGITAL
SIGNAL
10k
20k
20k
VCC = 3V
COAX LINE
MAX9140
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
9
Chip Information
PROCESS: Bipolar
Note: All E-grade devices are specified over the -40°C to +85°C
operating temperature range. All A-grade devices are specified
over the -40°C to +125°C operating temperature range.
+Denotes a lead(Pb)-free/RoHS-compliant package.
-Denotes a package containing lead(Pb).
T = Tape and reel.
Ordering Information
PART* PIN-PACKAGE TOP MARK
MAX9140AAUK+T 5 SOT23 +AFEJ
MAX9140AAXK+T 5 SC70 +ASW
MAX9140AAXK/V+T 5 SC70 +AUG
MAX9140EXK-T 5 SC70 ACC
MAX9140EUK-T 5 SOT23 ADQP
MAX9141EKA-T 8 SOT23 AAFD
MAX9141ESA 8 SO
MAX9142EKA-T 8 SOT23 AAFE
MAX9142ESA 8 SO
MAX9144EUD 14 TSSOP
MAX9144ESD 14 SO
PACKAGE TYPE PACKAGE CODE DOCUMENT NO. LAND PATTERN NO.
8 SOT23 K8-5 21-0078 90-0176
5 SOT23 U5-1 21-0057 90-0174
5 SC70 X5+1 21-0076 90-0188
14 TSSOP U14-1 21-0066 90-0113
8 SO S8-2 21-0041 90-0096
14 SO S14-1 21-0041 90-0112
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
www.maximintegrated.com Maxim Integrated
10
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 6/01 Initial release
1 1/07 Updated Absolute Maximum Ratings with ±20mA current into input pin. 2
2 12/07 Added two new automotive grade products. 1, 2
3 1/10 Added automotive qualied part 1
4 6/14 Added Junction Temperature to Absolute Maximum Ratings 2
5 9/15 Removed MAX9140AAXK/V from Ordering Information and edited the
Absolute Maximum Ratings 1, 2
6 10/15 Updated TOC7 and TOC8 in the Typical Operating Characteristics section 6
7 11/17 Added AEC statement to Features section and updated Ordering Information
table 1, 9
8 1/19 Removed embedded package outline drawings 10–13
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
MAX9140/MAX9141/
MAX9142/MAX9144
40ns, Low-Power, 3V/5V, Rail-to-Rail
Single-Supply Comparators
© 2019 Maxim Integrated Products, Inc.
11
Revision History
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.