OUTLINE
1
This product can fix CX-400 series, EQ-20 series, EX-40 series, reflectors (RF-210, RF-220, and RF-230), and fibers (FD-L51, FD-L52, FD-L53, FD-L54,
and M3/M4/M6 threaded head fiber) at any angle or position.
Two types of the mounting stand, MS-AJ1 which can be mounted on a horizontal surface and MS-AJ2 which can be mounted on a vertical surface, are
available.
ASSEMBLY
3
CAUTIONS
4
The tightening torque of the attached M4 hexagon-socket-head bolts ( , , and in ) should be 1.2N m or less.
To mount the stand on your equipment, use M6 screws. The tightening torque should be 2N m or less.
(Please arrange the M6 screws separately.)
Take care that if excessive torque is applied, the products may get damaged.
When using the stand, take care that excess vibration is not applied to the sensor.
Do not apply excess stress on any part of the stand.
Do not thread the fiber cable into the pipe when the fiber head is mounted on MS-AJ1-F, MS-AJ2-F.
Refer to the instruction manual attached to each product for details of CX-400 series, EQ-20 series, EX-40 series or fibers.
ASSEMBLY
3
Assembly diagram
PART COMPOSITION
2
Note: The numbers shown in the table adove indicate the quantities of the respective parts.
Arm joint
unit
Fiber mounting
bracket
Sensor
mounting unit
Fiber
mounting unit
Reflector
mounting unit
Assembly
for fiber
Basic
assembly
Lateral arm
assembly
Assembly
for reflector
MS-AJ1
MS-AJ2 MS-AJG
(Cable guide)
2
2
1
1
1
1
1
1
1
1
2
2
1
1
2
1
2
1
1
1
1
1
1
2
2
2
1
1
1
1
2
2
1
1
1
2
1
1
1
1
1
M4 (length 15mm) hexagon-socket-head bolt (Drilube applied product)
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
3
1
1
3
2
1
1
2
1
1
1
1
2
2
1
1
2
1
5
1
1
1
1
1
1
1
2
2
1
1
1
3
1
1
3
2
1
2
1
1
1
1
1
1
5
1
Fiber mounting bracket
M4 (length 8mm) screw with washers for RF-230
M3 (length 8mm) screw with washers for RF-220
Reflector mounting bracket
Auxiliary mounting plate for EX-40 series
M3 (length 16mm) screw with washers for EX-40 series
Auxiliary mounting plate for EQ-20 series
M3 (length 18mm) screw with washers for EQ-20 series
M3 (length 14mm) screw with washers for CX-400 series
M4 flat washer
M4 spring washer
M4 nut
M4 (length 22mm) hexagon-socket-head bolt
M4 (length 12mm) hexagon-socket-head bolt (Drilube applied product)
Arm joint
Cable guide
Sensor mounting bracket
Attachment
Arm (Pipe)
Base for vertical mounting (Accessory for MS-AJ2 )
Base for horizontal mounting (Accessory for MS-AJ1 )
No.
MS-AJP
[Arm (Pipe)]
MS-AJ1B
MS-AJ2B
(Base unit)
MS-AJLMS-FD-1MS-AJDMS-AJR
Reflector
mounting bracket
MS-AJ-R1
MS-AJS
MS-AJ1-F
MS-AJ2-F
MS-AJ1-M
MS-AJ2-M
MS-AJ1-A
MS-AJ2-A
stnenopmoCstes ylbmessAType
Model No.
Designation
Note: The assembly for reflector (MS-AJ -M) does not contain the
cable guide.
MS-AJ1, MS-AJ2, MS-AJ1-M, MS-AJ2-M
The MS-AJ1-M, MS-AJ2-M (assembly for
reflector) includes parts enclosed by the dotted
line in place of the sensor mounting bracket.
e.g.: RF-230
e.g.: CX-400 series
The base of MS-AJ2
differs.
Note: To adjust the arm joint, loosen both the M4 (length 12mm)
hexagon-socket-head bolts.
MS-AJ1-A, MS-AJ2-A, MS-AJ1-F, MS-AJ2-F
The MS-AJ1-F, MS-AJ2-F (assembly for fiber) includes
parts enclosed by the dotted line in place of the sensor
mounting bracket.
e.g.: FD-L51
e.g.: CX-400 series
The base of MS-AJ2
differs.
Mounting example
The below figure shows
the CX-400 series on
MS-AJ1.
DIMENSIONS (Unit: mm)
5
MS-AJ1, MS-AJ2 (Basic assembly)
Two M3 (length 14mm) screws with washers,
two M3 (length 16mm) screws with washers,
two M3 (length 18mm) screws with washers,
one auxiliary mounting plate for EQ-20 series
and one auxiliary mounting plate for EX-40
series are attached.
Notes: 1)
2)
3)
The dimensions in the brackets indicate the adjustable range of the movable
part.
This value is 210mm for MS-AJ2.
This value is 36.5mm for MS-AJ2.
The base of MS-AJ2
differs.
3124.515
8
2- 6.6 mounting holes
46
32
10
20
10
25.5
2- 6.6 mounting holes
32
(44.5)
(Note 3)
218
(Note 2)
(147)
(Note 1)
28
45
20
20 t 2
17.8
6
11.8 12
(POM)
Cable guide
Attachment
(Nylon 6)
10 arm (pipe)
[Stainless steel (SUS304)]
Base
(PA)
4
20
28
1
1
20
20
2533
3.2
18
8
Sensor mounting bracket
[Stainless steel (SUS304)]
2- 3.2 mounting
holes
2-3.2 4.2 oblong
holes
M4 hexagon-socket-
head bolt
4.2
45
45
MS-AJ1-A, MS-AJ2-A (Lateral arm assembly)
Notes: 1)
2)
3)
4)
5)
The dimensions in the brackets indicate the adjustable range of the movable
part.
Refer to MS-AJ1, MS-AJ2 (basic assembly) for the assembly diagram with
the base or sensor mounting bracket.
This value is 210mm for MS-AJ2-A.
This value is 36.5mm for MS-AJ2-A.
This value is 208.5mm for MS-AJ2-A.
Two M3 (length 14mm) screws with washers,
two M3 (length 16mm) screws with washers,
two M3 (length 18mm) screws with washers,
one auxiliary mounting plate for EQ-20 series
and one auxiliary mounting plate for EX-40
series are attached.
(
203.5
)
(Note 5)
28.45
12
16.5
6
20
45
Base (Note 2)
(PA)
(POM)
Cable guide
218
(Note 3)
33
(147)
(Note 1)
(44.5)
(Note 4)
25.5
2- 3.2 mounting
holes
2-3.2 4.2 oblong
holes
Arm joint
(Nylon 6)
Sensor mounting
bracket
[Stainless steel (SUS304)]
(Note 2)
(134) (Note 1) (33)
210
(16.5)
10 arm (pipe)
[Stainless steel (SUS304)]
10 arm (pipe)
[Stainless steel (SUS304)]
8
18
Fiber mounting bracket / MS-FD-1
Material: Stainless steel (SUS304)
6
7
9
13.5
18.5
22
13 8
8
3.2 4.2
8
5.5 4
4
3.2 13
35 55
13 22
R14
40
4 mounting hole
4-M3 0.5
2-M3 0.5
t 2
M3 threaded head fiber mounting hole
M3 threaded head fiber mounting hole
M3 threaded head fiber mounting hole
MS-AJ1-F, MS-AJ2-F (Assembly for fiber)
Notes: 1)
2)
3)
4)
5)
The dimensions in the brackets indicate the adjustable range of the movable
part.
Refer to MS-AJ1, MS-AJ2 (basic assembly) for the assembly diagram with
the base.
This value is 210mm for MS-AJ2-F.
This value is 36.5mm for MS-AJ2-F.
This value is 208.5mm for MS-AJ2-F.
218
(Note 3)
20
45
Base (Note 2)
(PA)
28.45
12
16.5
6
(POM)
Cable guide
33
(147)
(Note 1)
(44.5)
(Note 4)
(
203.5
)
(Note 5)
25.5
4-M3 0.5
mounting holes
Arm joint
(Nylon 6)
Fiber mounting
bracket
[Stainless steel (SUS304)]
(Note 2)
(134) (Note 1) (33)
210
(16.5)
10 arm (pipe)
[Stainless steel (SUS304)]
10 arm (pipe)
[Stainless steel (SUS304)]
8
18
Notes: 1)
2)
The dimensions in the brackets indicate the adjustable range of the movable
part.
Refer to MS-AJ1, MS-AJ2 (basic assembly) for the assembly diagram with
the base.
This value is 143.5mm for MS-AJ2-M.
This value is 200mm for MS-AJ2-M.
This value is 40mm for MS-AJ2-M.
MS-AJ1-M, MS-AJ2-M (Assembly for reflector)
Two M3 (length 8mm) screws with
washers and two M4 (length 8mm)
screws with washers are attached.
(208)
(Note 4)
(147)
(Note 1)
(Note 3)
(44.5)
(Note 5)
28
20
45
25 40 50
11.8
1220
10 arm (pipe)
[Stainless steel (SUS304)]
Base (Note 2)
(PA)
(Nylon 6)
Attachment
25.5
t 2
28 20
4.2
45
45
M4 hexagon-socket-
head bolt
8
18
Universal Sensor Mounting Stand
MS-AJ1
Horizontal mouting type
MS-AJ2
Vertical mounting type
INSTRUCTION MANUAL
Thank you very much for purchasing Panasonic products. Please read this
Instruction Manual carefully and thoroughly for the correct and optimum use
of this product. Kindly keep this manual in a convenient place for quick
reference.
http://panasonic.net/id/pidsx/global
PRINTED IN JAPAN © Panasonic Industrial Devices SUNX Co., Ltd. 2012
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
About our sale network, please visit our website.
MJE-MSAJ1 No.0035-06V
