DS2165QN+ - Maxim Integrated Products, Inc.

1 of 17 070802

Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple

revisions of any device may be simultaneously available through various sales channels. For information about device errata,

click here: http://www.maxim-ic.com/errata.

FEATURES

§ Compresses/expands 64kbps PCM voice

to/from either 32kbps, 24kbps, or 16kbps

§ Dual fully independent channel architecture;

device can be programmed to perform either:

- two expansions

- two compressions

- one expansion and one compression

§ Interconnects directly to combo-codec

devices

§ Input to output delay is less than 375ms

§ Simple serial port used to configure the

device

§ On-board time-slot assigner-circuit (TSAC)

function allows data to be input/output at

various time slots

§ Supports Channel Associated Signaling

§ Each channel can be independently idled or

placed into bypass

§ Available hardware mode requires no host

processor; ideal for voice storage

applications

§ Single +5V supply; low-power CMOS

technology

§ Available in 28-pin PLCC

§ 3V operation version is available

(DS2165QL)

PIN ASSIGNMENT (Top View)

DESCRIPTION

The DS2165Q ADPCM processor chip is a dedicated digital-signal-processing (DSP) chip that has been

optimized to perform adaptive-differential pulse-code modulation (ADPCM) speech compression at three

different rates. The chip can be programmed to compress (expand) 64kbps voice data down to (up from)

either 32kbps, 24kbps, or 16kbps. The compression to 32kbps follows the algorithm specified by CCITT

Recommendation G.721 (July 1986) and ANSI document T1.301 (April 1987). The compression to

24kbps follows ANSI document T1.303. The compression to 16kbps follows a proprietary algorithm

developed by Dallas Semiconductor. The DS2165Q can switch compression algorithms on-the-fly. This

allows the user to make maximum use of the available bandwidth on a dynamic basis.

28-Pin PLCC

FSY

YOUT

SDI

SCLK

XOUT

A5 NC

TM1

TM0

RST

VDD

YIN

CLKY

SPS

MCL

VSS

XIN

CLK

4 3 2 1 28 27 26

12 13 14 15 16 17 18

www.maxim-ic.com

DS2165Q

16/24/32kbps ADPCM Processo

DS2165Q

2 of 17

OVERVIEW

The DS2165Q contains three major functional blocks: a high performance (10 MIPS) DSP engine, two

independent PCM interfaces (X and Y) that connect directly to serial time-division-multiplexed (TDM)

backplanes, and a serial port that can configure the device on-the-fly by an external controller. A 10MHz

master clock is required by the DSP engine. The DS2165Q can be configured to perform either two

expansions, two compressions, or one expansion and one compression. The PCM/ADPCM data interfaces

support data rates from 256kHz to 4.096MHz. Typically, the PCM data rates are 1.544MHz for m-law and

2.048MHz for A-law. Each channel on the device samples the serial input PCM or ADPCM bit stream

during a user-programmed input time slot, processes the data and outputs the result during a user-

programmed output time slot.

Each PCM interface has a control register that specifies functional characteristics (compress, expand,

bypass, and idle), data format (m-law or A-law), and algorithm reset control. With the SPS pin strapped

high, the software mode is enabled and the serial port can be used to configure the device. In this mode, a

novel addressing scheme allows multiple devices to share a common 3-wire control bus, simplifying

system-level interconnect.

With SPS low, the hardware mode is enabled. This mode disables the serial port and maps certain control

controller is required and all PCM/ADPCM input and output time slots default to time slot 0.

HARDWARE RESET

RST allows the user to reset both channel algorithms and the contents of the internal registers. This pin

must be held low for at least 1ms on system power-up after the master clock is stable to ensure that the

device has initialized properly. RST should also be asserted when changing to or from the hardware

mode. RST clears all bits of the control register for both channels except the IPD bits; the IPD bits for

both channels are set to 1.

SOFTWARE MODE

Connecting SPS high enables the software mode. In this mode, an external host controller writes

configuration data to the DS2165Q by the serial port through inputs SCLK, SDI, and CS (Figure 2). Each

write to the DS2165Q is either a 2-byte write or a 4-byte write. A 2-byte write consists of the

address/command byte (ACB), followed by a byte to configure the control register (CR) for either the X

or Y channel. The 4-byte write consists of the ACB, followed by a byte to configure the CR, and then 1

byte to set the input time slot and another byte to set the output time slot.

ADDRESS/COMMAND BYTE

In the software mode, the address/command byte is the first byte written to the serial port; it identifies

which of the 64 possible ADPCM processors sharing the port wiring is to be updated. Address data must

match that at inputs A0 to A5. If no match occurs, the device ignores the following configuration data. If

an address match occurs, the next 3 bytes written are accepted as control, input and output time slot data.

Bit ACB.6 determines which side (X or Y) of the device is to be updated. The PCM and ADPCM outputs

are tri-stated during register updates.

DS2165Q

3 of 17

CONTROL REGISTER

The control register establishes idle, algorithm reset, bypass, data format, and channel coding for the

selected channel.

The X-side and Y-side PCM interfaces can be independently disabled (output tri-stated) by IPD. When

IPD is set for both channels, the device enters a low-power standby mode. In this mode, the serial port

must not be operated faster than 39kHz.

ALRST resets the algorithm coefficients for the selected channel to their initial values. ALRST is cleared

by the device when the algorithm reset is complete.

Table 1. PIN DESCRIPTION

PIN SYMBOL TYPE FUNCTION

2RST IReset. A high-low-high transition resets the algorithm. The device should be

reset on power-up and when changing to or from the hardware mode.

TM0

TM1 ITest Modes 0 and 1. Connect to VSS for normal operation.

IAddress Select. A0 = LSB, A5 = MSB. Must match address/command word

to enable the serial port.

12 SPS I Serial Port Select. Connect to VDD to select the serial port; connect to VSS to

select the hardware mode.

13 MCLK I Master Clock. 10MHz clock for the ADPCM processing engine; may be

asynchronous to SCLK, CLKX, and CLKY.

14 VSS — Signal Ground. 0V

16 XIN I X Data In. Sampled on falling edge of CLKX during selected time slots.

17 CLKX I X Data Clock. Data clock for the X-side PCM interface; must be

synchronous with FSX.

18 FSX I X Frame Sync. 8kHz frame sync for the X-side PCM interface.

20 XOUT O X Data Output. Updated on rising edge of CLKX during selected time slots.

21 SCLK I Serial Data Clock. Used to write to the serial port registers.

22 SDI I Serial Data In. Data for on-board control registers; sampled on the rising

edge of SCLK. LSB sent first.

23 CS IChip Select. Must be low to write to the serial port.

24 YOUT O Y Data Output. Updated on rising edge of CLKY during selected time slots.

25 FSY I Y Frame Sync. 8kHz frame sync for the Y-side PCM interface.

26 CLKY I Y Data Clock. Data clock for the Y-side PCM interface; must be

synchronous with FSY.

27 YIN I Y Data In. Sampled on falling edge of CLKY during selected time slots.

28 VDD — Positive Supply. 5.0V (3.0V for DS2165QL)

DS2165Q

4 of 17

Figure 1. BLOCK DIAGRAM

Figure 2. SERIAL PORT WRITE

Note: A 2-byte write is shown.

The bypass feature is enabled when BYP is set and IPD is cleared. During bypass, no expansion or

compression occurs. Bypass operates on bytewide (8 bits) slots when CP/ EX is set and on nibble-wide

(4 bits) slots when CP/ EX is cleared.

A-law (U/

= 0) and m-law (U/

= 1) PCM coding is independently selected for the X and Y channels

by CR.2. If BYP and IPD are cleared, then CP/ EX determines if the input data is to be compressed or

expanded.

DS2165Q

5 of 17

Figure 3. ADDRESS/COMMAND BYTE

(MSB) (LSB)

—X/ YA5 A4 A3 A2 A1 A0

SYMBOL POSITION FUNCTION

— ACB.7 Reserved. Must be 0 for proper operation

X/ YACB.6

X/Y Channel Select

0 = update channel Y characteristics

1 = update channel X characteristics

A5 ACB.5 MSB of device address

A4 ACB.4 —

A3 ACB.3 —

A2 ACB.2 —

A1 ACB.1 —

A0 ACB.0 LSB of device address

Figure 4. CONTROL REGISTER

(MSB) (LSB)

AS0 AS1 IPD ALRST BYP U/

AS2 CP/ EX

SYMBOL POSITION FUNCTION

AS0 CR.7 Algorithm Select 0 (Table 2)

AS1 CR.6 Algorithm Select 1 (Table 2)

IPD CR.5

Idle and Power-Down

0 = channel enabled

1 = channel disabled (output tri-stated)

ALRST CR.4

Algorithm Reset

0 = normal operation

1 = reset algorithm for selected channel

BYP CR.3

Bypass

0 = normal operation

1 = bypass selected channel

CR.2

Data Format

0 = A-law

1 = m-law

AS2 CR.1 Algorithm Select 2 (Table 2)

CP/ EX CR.0

Channel Coding

0 = expand (decode) selected channel

1 = compress (encode) selected channel

DS2165Q

6 of 17

Table 2. ALGORITHM SELECT BITS

ALGORITHM SELECTED AS2 AS1 AS0

64kbps to/from 32kbps 0 0 0

64kbps to/from 24kbps 1 1 1

64kbps to/from 16kbps 1 0 1

Figure 5. INPUT TIME SLOT REGISTER

(MSB) (LSB)

——-D5D4D3D2D1 D0

SYMBOL POSITION FUNCTION

— ITR.7 Reserved. Must be 0 for proper operation

— ITR.6 Reserved. Must be 0 for proper operation

D5 ITR.5 MSB of input time slot register

D4 ITR.4 —

D3 ITR.3 —

D2 ITR.2 —

D1 ITR.1 —

D0 ITR.0 LSB of input time slot register

Figure 6. OUTPUT TIME SLOT REGISTER

(MSB) (LSB)

— — D5 D4 D3 D2 D1 D0

SYMBOL POSITION FUNCTION

— OTR.7 Reserved. Must be 0 for proper operation

— OTR.6 Reserved. Must be 0 for proper operation

D5 OTR.5 MSB of output time slot register

D4 OTR.4 —

D3 OTR.3 —

D2 OTR.2 —

D1 OTR.1 —

D0 OTR.0 LSB of output time slot register

DS2165Q

7 of 17

TIME SLOT ASSIGNMENT/ORGANIZATION

On-board counters establish when PCM and ADPCM I/O occur. The counters are programmed by the

time slot registers. Time slot size (number of bits wide) is determined by the state of CP/ EX . The number

of time slots available is determined by the state of both CP/ EX and U/

(Figures 7 through 10). For

example, if the X channel is set to compress (CP/ EX = 1) and it is set to expect m-law data

(U/

= 1), then the input port (XIN) is set up for 32 8-bit time slots and the output port (XOUT) is set up

for 64 4-bit time slots. The time slot organization is not dependent on which algorithm has been selected.

Note: Time slots are counted from the frame sync signal starting at the first rising edge of either CLKX

or CLKY after the frame sync.

Figure 7. m-LAW PCM INTERFACE

Figure 8. m-LAW ADPCM INTERFACE

DS2165Q

8 of 17

Figure 9. A-LAW PCM INTERFACE

Figure 10. A-LAW ADPCM INTERFACE

DS2165Q

9 of 17

HARDWARE MODE

The hardware mode is intended for applications that do not have an external controller available or do not

require the extended features offered by the serial port. Connecting the SPS pin to VSS disables the serial

port, clears all internal register bits, and maps the IPD, U/

, and CP/ EX bits for both channels to external

bits (Table 3). In the hardware mode, both the input and output time slots default to time slot 0.

Table 3. HARDWARE MODE

# NAME REGISTER LOCATION FUNCTION

6A0 CP/ EX

(Channel X)

Channel X Coding Configuration

0 = Expand

1 = Compress

7A1 AS0/AS1/AS2

(Channel X and Y) Algorithm Select (Table 4)

8A2 U/

(Channel X)

Channel X Data Format

0 = A-law

1 = m-law

9A3 CP/ EX

(Channel Y)

Channel Y Coding Configuration

0 = Expand

1 = Compress

10 A4 AS0/AS1/AS2

(Channel X and Y) Algorithm Select (Table 4)

11 A5 U/

(Channel Y)

Channel Y Data Format

0 = A-law

1 = m-law

22 SDI IPD

(Channel Y)

Channel Y Idle Select

0 = Channel Active

1 = Channel Idle

23 CS

IPD

(Channel X)

Channel X Idle Select

0 = Channel Active

1 = Channel Idle

NOTES:

1) SCLK must be connected to VSS when the hardware mode is selected.

2) When both channels are idled, power consumption is significantly reduced.

3) The NIL powers up within 800ms after either channel is returned to active from an idle state.

DS2165Q

10 of 17

Table 4. ALGORITHM SELECT FOR HARDWARE MODE

ALGORITHM CONFIGURATION OF A1 AND A4

64kbps to/from 32kbps Connect both A1 and A4 to VSS.

64kpbs to/from 24kbps

Hold A1 and A4 low during a hardware reset;

take both A1 and A4 high after the RST pin

has returned high (allow 3ms after RST

returns high before taking A1 and A4 high).

64kbps to/from 16kbps Connect both A1 and A4 to VDD.

Figure 11. DS2165Q CONNECTION TO CODEC/FILTER

Suggested Codec/Filters*

TP305X National Semiconductor

ETC505X STMicroelectronics

MC1455XX Motorola, Inc.

TCM29CXX Texas Instruments Incorporated

HD44238C Hitachi

*Other generic codec/filter devices can be substituted.

DS2165Q

11 of 17

PCM AND ADPCM INPUT/OUTPUT

Since the organization of the input and output time slots on the DS2165Q does not depend on the

algorithm selected, it always assumes that PCM input and output are in 8-bit bytes and that ADPCM

input and output are in 4-bit bytes. Figure 12 demonstrates how the DS2165Q handles the I/O for the

three different algorithms. In the figure, it is assumed that channel X is in the compression mode

(CP/ EX = 1) and channel Y is in the expansion mode (CP/ EX = 0). Also, it is assumed that both the input

and output time slots for both channels are set to 0.

Figure 12. PCM AND ADPCM I/O EXAMPLE

Note 1: The bit after the LSB in the 24kbps ADPCM output is only a 1 when the DS2165Q is operated

in the software mode and is programmed to perform 24kbps compression; in all other configurations, it is

a 0.

DS2165Q

12 of 17

TIME SLOT RESTRICTIONS

Under certain conditions, the DS2165Q does contain some restrictions on the output time slots that are

available. These restrictions are covered in detail in a separate application note. No restrictions occur if

the DS2165Q is operated in the hardware mode.

INPUT TO OUTPUT DELAY

With all three compressions algorithms, the total delay, from the time the PCM data sample is captured

by the DS2165Q to the time it is output, is always less than 375ms. The exact delay is determined by the

input and output time slots selected for each channel.

CHANNEL ASSOCIATED SIGNALING

The DS2165Q supports Channel Associated Signaling (CAS) through its ability to automatically change

from the 32kbps compression algorithm to the 24kbps algorithm. If the DS2165Q is configured to

perform the 32kbps algorithm, then in both the hardware and software mode it senses the frame sync

inputs (FSX and FSY) for a double-wide frame-sync pulse. Whenever the DS2165Q receives a double-

wide pulse, it automatically switches from the 32kbps algorithm to the 24kbps algorithm. Switching to

the 24kbps algorithm allows the user to insert signaling data into the LSB bit position of the ADPCM

output because this bit does not contain any useful speech information.

ON-THE-FLY ALGORITHM SELECTION

In the software mode, the user can switch between the three available algorithms on-the-fly. That is, the

DS2165Q does not need to be reset or stopped to make the change from one algorithm to another. The

DS2165Q reads the control register before it starts to process each PCM or ADPCM sample. If the user

wishes to switch algorithms, then the control register must be updated by the serial port before the first

input sample to be processed with the new algorithm arrives at either XIN or YIN. The PCM and

ACPCM outputs tri-state during register updates.

DS2165Q

13 of 17

ABSOLUTE MAXIMUM RATINGS*

Voltage Range on Any Pin Relative to Ground -1.0V to +7.0V

Operating Temperature Range 0°C to +70°C

Storage Temperature Range -55°C to +125°C

Soldering Temperature Range See IPC/JEDEC J-STD-020A

*This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operation

sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect reliability.

RECOMMENDED DC OPERATING CONDITIONS (TA = 0°C to +70°C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Logic 1 VIH 2.0 VCC + 0.3 V 5, 7

Logic 0 VIL -0.3 +0.8 V 5

Supply VDD 4.5 5.5 V 5

Logic 1 VIH 2.2 VCC + 0.3 V 6

Logic 0 VIL -0.3 +0.4 V 6

Supply VDD 2.7 3.6 V 6

CAPACITANCE (TA = +25°C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Input Capacitance CIN 5pF

Output Capacitance COUT 10 pF

DC ELECTRICAL CHARACTERISTICS (VDD = 5V ±10%, TA = 0°C to +70°C;

VDD = 3.0V + 20% - 10% for DS2165QL)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Active Supply Current IDDA 20 mA 1, 2, 5

Active Supply Current IDDA 12 mA 1, 2, 6

Idle Supply Current IDDPD 1 mA 1, 2, 3

Input Leakage II-1.0 +1.0 mA

Output Leakage IO-1.0 +1.0 mA4

Output Current (2.4V) IOH -1.0 mA 5

Output Current (0.4V) IOL +4.0 mA 5

Output Current (2.2V) IOH -0.5 mA 6

Output Current (0.4V) IOL +2.0 mA 6

NOTES:

1) CLKX = CLKY = 1.544MHz; MCLK = 10MHz

2) Outputs open; inputs swinging full supply levels.

3) Both channels in idle mode.

4) XOUT and YOUT are tri-stated.

5) Applies only to 5V device.

6) Applies only to 3V device (DS2165QL).

7) CLKX, CLKY, MCLK VIH MIN = 2.4V

DS2165Q

14 of 17

PCM INTERFACE, AC ELECTRICAL CHARACTERISTICS

(VDD = 5V ±10%, TA = 0°C to +70°C; VDD = 3.0V + 20% - 10% for DS2165QL)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

CLKX, CLKY Period tPXY 244 3906 ns 1

CLKX, CLKY Pulse Width tWXYL

tWXYH

100 ns

CLKX, CLKY Rise Fall Times tRXY

tFXY

10 20 ns

Hold Time from CLKX, CLKY to FSX,

FSY tHOLD 0ns2

Setup Time from FSX, FSY High to

CLKX, CLKY Low tSF 50 ns 2

Hold Time from CLKX, CLKY Low to

FSX, FSY Low tHF 100 ns 2

Setup Time for XIN, YIN to CLKX,

CLKY Low tSD 50 ns 2

Hold Time for XIN, YIN to CLKX,

CLKY Low tHD 50 ns 2

Delay Time from CLKX, CLKY to

Valid XOUT, YOUT tDXYO 10 150 ns 3

Delay Time from CLKX, CLKY to

XOUT, YOUT Tri-stated tDXYZ 20 150 ns 2, 3, 4

NOTES:

1) Maximum width of FSX and FSY is one CLKX or CLKY period (except for signaling frames).

Maximum operating frequency is guaranteed by design and is not a tested parameter.

2) Measured at VIH = 2.0V, VIL = 0.8V, and 10ns maximum rise and fall times.

3) Load = 150pF + 2 LSTTL loads.

4) For LSB of PCM or ADPCM byte.

MASTER CLOCK/RESET, AC ELECTRICAL CHARACTERISTICS

(VDD = 5V ±10%, TA = 0°C to +70°C; VDD = 3.0V + 20% - 10% for DS2165QL)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

MCLK Period tPM 100 ns 1

MCLK Pulse Width tWMH,

tWML

45 50 55 ns

MCLK Rise/Fall Times tRM, tFM 10 ns

RST Pulse Width tRST 1ms

NOTES:

1) MCLK = 10MHz ±500ppm

DS2165Q

15 of 17

SERIAL PORT, AC ELECTRICAL CHARACTERISTICS

(VDD = 5V ±10%, TA = 0°C to +70°C; VDD = 3.0V + 20% - 10% for DS2165QL)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

SDI to SCLK Setup tDC 55 ns 1

SCLK to SDI Hold tCDH 55 ns 1

SCLK Low Time tCL 250 ns 1

SCLK High Time tCH 250 ns 1

SCLK Rise and Fall Time tR, tF100 ns 1

CS to SCLK Setup tCC 50 ns 1

SCLK to CS Hold tCCH 250 ns 1

CS Inactive Time tCWH 250 ns 1

SCLK Setup to CS Falling tSCC 50 ns 1

NOTES:

1) Measured at VIH = 2.0V, VIL = 0.8V, and 10ns maximum rise and fall times.

DS2165Q

16 of 17

Figure 13. PCM INTERFACE AC TIMING DIAGRAM

Figure 14. MASTER CLOCK/RESET AC TIMING DIAGRAM

Figure 15. SERIAL PORT AC TIMING DIAGRAM

Note: SCLK can be either high or low when CS is taken low.

DS2165Q

17 of 17

28-PIN PLCC

INCHES

DIM MIN MAX

A0.165 0.180

A1 0.090 0.120

A2 0.020 —

B0.026 0.033

B1 0.013 0.021

C0.009 0.012

D0.485 0.495

D1 0.450 0.456

D2 0.390 0.430

E0.485 0.495

E1 0.450 0.456

E2 0.390 0.430

L1 0.060 —

N28 —

e1 0.050 BSC

CH1 0.042 0.048