1
dc996f
DEMO MANUAL DC996
DESCRIPTION
LTC2208/LTC2208-14/LTC2217/
LTC2216/LTC2215
16-Bit/14-Bit 80Msps to130Msps
ADCs
Demonstration circuit 996 supports a family of 16-/14-bit
80Msps to 130Msps ADCs. Each assembly features one of
the following devices: LTC
®
2208, LTC2208-14, LTC2217,
LTC2216, LTC2215 high speed, high dynamic range ADCs.
This demonstration circuit only supports LVDS operation.
For demonstration of CMOS output signaling, please see
DC854.
Other members of this family include the LTC2207, a
105Msps 16-bit CMOS-only version of this device, as
well as lower speed versions and single-ended clock ver-
sions. These 7mm × 7mm QFN devices are supported by
Demonstration Circuits 918 and 919 (for single-ended
clock input).
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and PScope
is a trademark of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
Several versions of the 996 demo board supporting the
LTC2208 16-bit, LTC2217 16-bit and LTC2208-14 14-bit
series of A/D converters are listed in Table 1. Depending on
the required resolution, sample rate and input frequency,
the DC996 is supplied with the appropriate ADC and with
an optimized input circuit. The circuitry on the analog inputs
is optimized for analog input frequencies below 70MHz
or from 70MHz to 140MHz. For higher input frequencies,
contact the factory for support.
Design files for this circuit board are available at
http://www.linear.com/demo
Table 1. DC996 Variants
DC996 VARIANTS ADC PART NUMBER RESOLUTION MAXIMUM SAMPLE RATE INPUT FREQUENCY
996B-A LTC2208 16-Bit 130Msps 1MHz to 70MHz
996B-B LTC2208 16-Bit 130Msps 70MHz to 140MHz
996B-C LTC2208-14 14-Bit 130Msps 1MHz to 70MHz
996B-D LTC2208-14 14-Bit 130Msps 70MHz to 140MHz
996B-E LTC2217 16-Bit 105Msps 1MHz to 70MHz
996B-F LTC2217 16-Bit 105Msps 70MHz to 140MHz
996B-G LTC2216 16-Bit 80Msps 1MHz to 70MHz
996B-H LTC2216 16-Bit 80Msps 70MHz to 140MHz
996B-I LTC2215 16-Bit 65Msps 1MHz to 70MHz
996B-J LTC2215 16-Bit 65Msps 70MHz to 140MHz
996A-P LTC2208 16-Bit 130Msps >140MHz
996A-Q LTC2208-14 14-Bit 130Msps >140MHz
2
dc996f
DEMO MANUAL DC996
QUICK START PROCEDURE
PERFORMANCE SUMMARY
(TA = 25°C)
PARAMETER CONDITION VALUE
Supply Voltage Depending On Sampling Rate and the A/D Converter Provided,
This Supply Must Provide Up To 700mA.
Optimized for 3.3V
[3.15V⇔3.45V Min/Max]
Analog Input Range Depending on PGA Pin Voltage 1.5VP-P to 2.25VP-P
Logic Input Voltages Minimum Logic High
Maximum Logic Low
2V
0.8V
Logic Output Voltages (Differential) Nominal Logic Levels (100Ω Load)
Minimum Logic levels (100Ω Load)
350mV/2.1V Common Mode
247mV/2.1V Common Mode
Sampling Frequency (Convert Clock Frequency) See Table 1
Convert Clock Level 50Ω Source Impedance, AC-Coupled or Ground Referenced
(Convert Clock Input Is Capacitor Coupled On Board and
Terminated with 50Ω.)
2VP-P⇔2.5VP-P Sine Wave or
Square wave
Resolution See Table 1
Input frequency range See Table 1
SFDR See Applicable Data Sheet
SNR See Applicable Data Sheet
Demonstration circuit 996 is easy to set up to evaluate
the performance of the LTC2208/LTC2208-14/LTC2217
A/D converters. Refer to Figure 1 for proper measurement
equipment setup and follow this procedure:
Setup
If a DC890 QuikEval™ II Data Acquisition and Collection
System was supplied with the DC996 demonstration
circuit, follow the DC890 Quick Start Guide to install the
required software and for connecting the DC890 to the
DC996 and to a PC.
DC996 Demonstration Circuit Board Jumpers
The DC996 demonstration circuit board should have the
following jumper settings as default: (as per Figure 1).
Figure 1 shows DC996A, the DC996B is shown in Figure 7.
J2: Mode (VCC) 2's Complement CDS Off
J3: SHDN: (Run) Dither (Off)
J4: Rand (Off) PGA 1x
J9: Unused power connector
Applying Power and Signals to the DC996
Demonstration Circuit
Apply 3.3V across the pins marked “+3.3V” and “PWR
GND” on the DC996. The DC996 demonstration circuit
requires up to 700mA depending on the sampling rate and
the A/D converter supplied. If a DC890 is used to acquire
data from the DC996, the DC890 must be provided with
an external 6V ±0.5V 1A supply on turrets G7(+) and
G1(–) or the adjacent 2.1mm power jack to support the
power requirements of the Xilinx Spartan 3 FPGA active
terminations used to terminate the LVDS repeaters on the
DC996. The DC890 will not activate the LVDS mode unless
the DC890 detects external power present.
If external power is not present the DC890 will not config-
ure the FPGA for LVDS terminations as this would result
in exceeding the USB 500mA limit. The DC890 contains
an onboard electronic circuit breaker which will shut off
the DC890 if external power is removed while the FPGA
is configured for LVDS active terminations.
3
dc996f
DEMO MANUAL DC996
QUICK START PROCEDURE
Figure 1. DC996A Setup (Zoom for Detail). See Figure 7 for DC996B
Encode Clock
Note: This is not a logic-compatible input. It is terminated
with 50Ω. Apply an encode clock to the SMA connector
on the DC996 demonstration circuit board marked “J7
ENCODE INPUT”. This is a transformer-coupled input,
terminated on the secondary side in two steps, 100Ω at
the transformer with final termination at the ADC at 100Ω.
For the best noise performance, the ENCODE INPUT
must be driven with a very low jitter source. When using
a sinusoidal generator, the amplitude should often be as
large as possible, up to 3VP-P or 13dBm. Using bandpass
filters on the clock and the analog input will improve the
noise performance by reducing the wideband noise power
of the signals. Data sheet FFT plots are taken with 10-pole
LC filters made by TTE (Los Angeles, CA) to suppress
signal generator harmonics, non-harmonically related
spurs and broad band noise. Low phase noise Agilent
8644B generators are used with TTE bandpass filters for
both the clock input and the analog input.
Apply the analog input signal of interest to the SMA con-
nectors on the DC996 demonstration circuit board marked
“J5 ANALOG INPUT”. These inputs are capacitive coupled
to Balun transformers ETC1-1-13, or directly coupled
through flux-coupled transformers ETC1-1T.
4
dc996f
DEMO MANUAL DC996
An internally generated conversion clock output is avail-
able on J1 which could be collected via a logic analyzer, or
other data collection system if populated with a SAMTEC
MEC8-150 type connector or collected by the DC890 Data
Acquisition Board using the PScope™ System Software
provided or downloaded from the Linear Technology
website at http://www.linear.com/designtools/software/.
If a DC890 was provided, follow the DC890 Quick Start
Guide and the instructions below.
To start the data collection software if “PScope.exe”, is
installed (by default) in \Program Files\LTC\PScope\, double
click the PScope Icon or bring up the run window under
the start menu and browse to the PScope directory and
select PScope.
If the DC996 demonstration circuit is properly connected to
the DC890, PScope should automatically detect the DC996,
and configure itself accordingly. If necessary the procedure
below explains how to manually configure PScope.
Under the Configure menu, go to ADC Configuration.
Check the Config Manually box and use the following
configuration options:
• 16-Bit (or 14-Bit if using LTC2208-14)
• Alignment: Left-16
• Bipolar (2’s complement)
• Positive clock edge
• Type: LVDS
If everything is hooked up properly, powered and a suit-
able convert clock is present, clicking the “Collect” button
should result in time and frequency plots displayed in
the PScope window. Additional information and help for
PScope is available in the DC890 Quick Start Guide and in
the online help available within the PScope program itself.
QUICK START PROCEDURE
Analog Input Network
For optimal distortion and noise performance the RC
network on the analog inputs should be optimized for the
analog input frequencies of interest. At this point in time,
the circuit in Figure 3 for input frequencies below 70MHz.
For input frequencies from 70MHz to 140MHz, the circuit
in Figure 2 is used. These two input networks cover a
broad bandwidth and are not optimized for operation at a
specific input frequency.
For higher frequencies, a single balun (ETC1-1-13) is
populated on a DC996A board.
In almost all cases, filters will be required on both analog
input and encode clock to provide data sheet SNR.
The filters should be located close to the inputs to avoid
reflections from impedance discontinuities at the driven
end of a long transmission line. Most filters do not present
50Ω outside the passband.
The DC996A board has provision for a bandpass filter
prior to the balun. This may be populated if the board is
customized for a given frequency band. (Figure 5)
In some cases, 3dB to 10dB pads may be required to
obtain low distortion.
If your generator cannot deliver full-scale signals without
distortion, you may benefit from a medium power ampli-
fier based on a Gallium Arsenide Gain block prior to the
final filter. This is particularly true at higher frequencies
where operational amplifiers may be unable to deliver
the combination of low noise figure and high IP3 point
required. A high order filter can be used prior to this final
amplifier, and a relatively lower Q filter used between the
amplifier and the demo circuit.
For advice on drive circuits or for input frequencies greater
than 220MHz, or for higher order bandpass filtering prior
to the ADC, contact the factory for support.
5
dc996f
DEMO MANUAL DC996
QUICK START PROCEDURE
0.1μF
AIN+
AIN–
2.2μF
VCM
LTC2208
ANALOG
INPUT
0.1μF
0.1μF 5Ω
33Ω
33Ω 5Ω
10Ω
49.9Ω
10Ω
T1
1:1
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
EXCEPT 2.2μF
T1
MA/COM ETC1-1-13
T2
COILCRAFT WBC1-1L
70MHz TO 200MHz
Figure 2. Analog Front-End Circuit For 70MHz+
Figure 3. Analog Front-End Circuit For 1MHz < AIN < 70MHz
0.1μF
AIN+
AIN–
2.2μF
8.2μF
VCM
LTC2208
ANALOG
INPUT
0.1μF
0.1μF 5Ω
33Ω
33Ω 5Ω
10Ω
49.9Ω
10Ω
T1
1:1
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
EXCEPT 2.2μF
T1
MA/COM ETC1-1-13
T2
COILCRAFT WBC1-1L
1MHz TO 70MHz
For input frequencies less than 5MHz, or greater than
150MHz, other input networks may be more appropriate.
Please consult the factory for suggestions on drivers
and networks if your signal sources extend outside these
ranges, or if you experience difficulties driving these sug-
gested networks.
As this board has a black solder mask, in order to improve
the thermal performance, Figure 4 is a picture of the top
side in colors that are easier to digest. The dielectric under
the input network (bluish pads) is 20 mils, otherwise,
dielectric thickness is 6 mils.
This board is used only for 200MHz+ applications. The
input network of Figure 5 is devised to be populated with
a bandpass filter.
Gerber or PDF files of this board are available.
If the higher frequency board is ordered without requesting
a bandpass filter, C6 is a counterpart to C7, providing a
DC block, C23 is a 0Ω resistor.
If this is populated as a BP filter, The reactance of L1 and
L3, and the series of C6 and C5 (and C21 and C23) should
be between 50Ω and 33Ω. The reactance of L2 should
match that of 1/2 C6^+C5.
The ratio of C5 to C6 will determine coupling be-tween the
two resonators, with a high ratio giving a narrow pass band.
As an example, for center frequency of 260MHz; –3dB
BW of 150MHz, C6, C23 = 27pF; C5, C21 = 68pF; L1, L3
= 18 nH; L2 = 7.5nH.
This has a flat passband over 80MHz. See Figure 6.
This filter is not intended as a band-defining filter, but
simply to minimize noise BW prior to the ADC, and to
minimize 2nd and 3rd originating in a drive amplifier. 2nd
harmonic of 260 is down at 1.
6
dc996f
DEMO MANUAL DC996
QUICK START PROCEDURE
Fi
gure
4
.
DC996A
A
r
t
wor
k
Figure 5. Input Filter for DC996A Board
7
dc996f
DEMO MANUAL DC996
QUICK START PROCEDURE
Figure 8. DC996B Artwork
Figure 6. Input Filter Frequency Response for DC996A Board
Figure 7. DC996B Board—Two Transformer Version
8
dc996f
DEMO MANUAL DC996
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC996A General BOM
1 0 C4 (Option) CAP~NPO~1.8pF~50V~0.25pF~0402 AVX, 04025A1R8CAT2A
2 1 C8 CAP~NPO~1.8pF~50V~0.25pF~0402 AVX, 04025A1R8CAT2A
3 1 C12 CAP~X5R~0.01μF~16V~10%~0402 AVX, 0402YC103KAT
4 15 C15-16, C20, C22, C25-32, C34-36 CAP~X5R~0.1μF~10V~10%~0402 AVX, 0402ZD104KAT
5 0 C10, C11 (Option)
6 6 C1-3, C6, C7, C23 CAP~X7R~0.01μF~16V~10%~0603 AVX, 0603YC103KAT
7 2 C18, C19 CAP~X7R~0.1μF~16V~10%~0603 AVX, 0603YC104KAT
8 0 C21 (Option)
9 2 C13, C17 CAP~X5R~2.2μF~10V~20%~0805 AVX, 0805ZD225MAT
10 3 C14, C24, C38 CAP~X5R~4.7μF~10V~20%~0805 AVX, 0805ZD475MAT
11 0 C5 (Option)
12 4 J2, J3, J4, J9 HEADER~3X2~2mm COMM_CON/2202S-06G2
13 2 J5, J7 CONN~SMA 50Ω EDGE-LAUNCH E.F. Johnson, 142-0701-851
14 0 L1 (Option)
15 1 L2 RES~0Ω_JUMPER~0603 AAC, CJ06-000M
16 0 L3 (Option)
17 19 R13, R16-23, R30-35, R38-41 RES~100Ω~5%~1/20~0201 VISHAY, CRCW0201100RJNED
18 1 R15 RES~100Ω~1%~1/16~0402 VISHAY, CRCW0402100RFKED
19 1 R24 RES~100k~1%~1/16~0402 VISHAY, CRCW0402100KFKED
20 2 R11-12 RES~33.2Ω~1%~1/16~0402 VISHAY, CRCW040233R2FKED
21 2 R1, R2 RES~49.9Ω~1%~1/16~0402 VISHAY, CRCW040249R9FKEA
22 6 R4, R5, R9, R10, R27, R28 RES~4.99Ω~1%~1/16W~0402 VISHAY, CRCW04024R99FKED
23 3 R25, R26, R29 RES~4990Ω~1%~1/16~0402 VISHAY, CRCW04024K99FKED
24 0 R3 (Option)
25 2 R14, R37 RES~100Ω~1%~1/16W~0603 VISHAY, CRCW0603100RFKEA
26 3 R6-8 RES~1000Ω~1%~1/16W~0603 VISHAY, CRCW06031K00FKEB
27 2 R42, R43 FERRITE BEAD~SMT~1206 MURATA, BLM31PG330SN1L
28 2 T1, T2 XFRM~RF~SMT~1:1 BALUN MACOM, MABA-007159-000000
29 1 U1 (Bal to 1298A) IC~SERIAL_EEPROM~TSSOP8 MICROCHIP, 24LC025-I /ST
30 2 U3, U4 BUFFER~LVDS~OCTAL FAIRCHILD, FIN1108MTDX
31 1 U5 BUFFER~LVDS~SINGLE FAIRCHILD, FIN1101K8X
32 4 TP1, TP2, TP4, TP5 TURRET MILL MAX, 2308-02-00-80-00-00-07-00
33 4 Z (STAND-OFF) STAND-OFF, NYLON 0.25'" tall KEYSTONE, 8831(SNAP ON)
34 5 SHUNT, 0.079" Center SAMTEC, 2SN-BK-G
35 2 STENCIL, 20X20 STENCIL 996A, 20X20
DC996A-P
1 1 U2 (DC996A-P) IC~ADC~130Msps~16-BIT~QFN-64 LINEAR_TECH/LTC2208CUP#PBF
2 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996A
DC996A-Q
1 1 U2 (DC996A-Q) IC~ADC~130Msps~14-BIT~QFN-64 LINEAR_TECH/LTC2208CUP-14#PBF
2 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996A
9
dc996f
DEMO MANUAL DC996
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC996B General BOM
1 5 C1-C3, C6-7 CAP~X7R~0.01μF~16V~10%~0603 AVX/0603YC103KAT
2 2 C13, C17 CAP~X5R~2.2μF~10V~20%~0805 AVX/0805ZD225MAT
3 3 C14, C24, C38 CAP~X5R~4.7μF~10V~20%~0805 AVX/0805ZD475MAT
4 15 C15-16, C20, C22, C25-C32, C34-C36 CAP~X5R~0.1μF~10V~10%~0402 AVX/0402ZD104KAT
5 0 C18, C19(Option) CAP~X7R~0.1μF~16V~10%~0603 AVX/0603YC104KAT
6 1 C4 (Also C9-C10 options) CAP~NPO~8.2pF~50V~0.25pF~0402 AVX/04025A8R2CAT2A
7 2 C5, C12 CAP~X5R~0.01μF~16V~10%~0402 AVX/0402YC103KAT
8 3 J2-4 HEADER~3 × 2~2mm COMM_CON/2202S-06G2
9 0 J9 (Option) HEADER~3 × 2~2mm COMM_CON/2202S-06G2
10 2 J5, J7 CONN~SMA 50Ω EDGE-LAUNCH AMPHENOL_CONNEX/132357
11 2 R42-R43 FERRITE BEAD~SMT~1206 MURATA/BLM31PG330SN1L
12 2 R9-R10 RES~10Ω~1%~1/16~0402 AAC/CR05-10R0FM
13 1 R15 RES~100Ω~1%~1/16~0402 AAC/CR05-1000FM
14 1 R37 RES~100Ω~1%~1/16W~0603 AAC/CR16-1000FM
15 19 R13, R16-R23, R30-R35, R38-R41 RES~100Ω~5%~1/20~0201 ACC/CR20-101JM
16 3 R6-8, R14 RES~1k~1%~1/16W~0603 AAC/CR16-1001FM
17 1 R24 RES~100k~1%~1/16~0402 AAC/CR05-1003FM
18 2 R1-R2 RES~49.9Ω~1%~1/16~0402 AAC/CR05-49R9FM
19 0 R3 (OPTION) RES~100Ω~1%~1/16W~0603 AAC/CR16-1000FM
20 2 R11-R12 RES~33.2Ω~1%~1/16~0402 AAC/CR05-33R2FM
21 3 R25, R26, R29 RES~4990Ω~1%~1/16~0402 AAC/CR05-4991FM
22 2 R27-R28 RES~10Ω~5%~1/20~0201 PANASONIC, ERJ-1GEJ100C
23 2 R4-R5 RES~5.1Ω~1%~1/16~0402 AAC/CR05-5R1FM
24 1 T3 XFRM~RF~SMT~1:1 BALUN M/A-COM, ETC1-1-13 (Leaded)
M/A-COM, MABA-007159-000000 (PbF)
25 4 TP1-2, TP4-5 TURRET MILL_MAX/2308-2
26 1 U1 IC~Serial_EEPROM~TSSOP8 MICROCHIP/24LC025-I /ST
27 2 U3, U4 BUFFER~LVDS~OCTAL FAIRCHILD/FIN1108MTD
28 1 U5 BUFFER~LVDS~SINGLE FAIRCHILD/FIN1101K8X
29 4 Z (STAND-OFF) STAND-OFF, NYLON 0.25" tall KEYSTONE, 8831(SNAP ON)
30 5 SHUNT, 0.079" Center SAMTEC, 2SN-BK-G
31 2 STENCIL, 20 × 20 STENCIL 996B, 20X20
DC996B-A
1 1 C8 CAP~NPO~4.7pF~50V~0.25pF~0402 AVX/04025A4R7CAT2A
2 2 C9-C10 CAVP~NPO~8.2pF~50V~0.25pF~0402 AVX/04025A8R2CAT2A
3 1 L1 IND~56nH~5%~0603 MURATA/LQP18MN56NG02D
4 2 R36, R44 RES~86.6~1%~1/16W~0603 AAC/CR16-86R6FM
5 1 R45 RES~86.6~1%~1/16~0402 AAC/CR05-86R6FM
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, ETC1-1-13 (Leaded)
M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 XFRM~RF~SMT~1:1CT M/A-COM, ETC1-1T (Leaded)
M/A-COM, MABAES0060 (PbF)
8 1 U2 (D/C 0619) ADC~16BIT~130MSPS (Lot# T23920.2) LINEAR/LTC2208IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT 996B-A
10
dc996f
DEMO MANUAL DC996
DC966B-E
1 1 C8 CAP~NPO~4.7pF~50V~0.25pF 0402 AVX, 04025A4R7CAT2A
2 2 C9-10 CAP~NPO~8.2pF~50V~0.25pF 0402 AVX, 04025A8R2CAT2A
3 1 L1 IND~56nH~5% 0603 MURATA, LQP18MN56NG02D
4 2 R36, R44 RES~86.6Ω~1%~1/16W 0603 VISHAY, CRCW060386R6FKEA
5 1 R45 RES~86.6Ω~1%~1/16 0402 VISHAY, CRCW040286R6FKED
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 XFRM~RF~SMT~1:1CT M/A-COM, MABAES0060 (PbF)
8 1 U2 ADC~16-BIT~105Msps LINEAR, LTC2217IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT 996B
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC996B-B
1 1 C8 CAP~NPO~1.8pF~50V~0.25pF~0402 AVX/04025A1R8CAT2A
2 2 C9-C10 CAP~NPO~3.9pF~50V~0.25pF~0402 AVX/04025A3R9CAT2A
3 1 L1 IND~18nH~5%~0603 MURATA/LQP18MN18NG02D
4 2 R36, R44 RES~43.2Ω~1%~1/16W~0603 AAC/CR16-43R2FM
5 1 R45 RES~182Ω_JUMPER~0402 AAC/CR05-1820FM
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, ETC1-1-13 (Leaded) M/A-COM,
MABA-007159-000000 (PbF)
7 1 T2 TRANSFORMER, WBC1-1L COILCRAFT, WBC1-1L
8 1 U2 D/C 0619 ADC~16-BIT~130Msps, Lot# T23920.2 LINEAR/LTC2208IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B-B
DC996B-C
1 1 C8 CAP~NPO~4.7pF~50V~0.25pF~0402 AVX/04025A4R7CAT2A
2 2 C9-C10 CAP~NPO~8.2pF~50V~0.25pF~0402 AVX/04025A8R2CAT2A
3 1 L1 IND~56nH~5%~0603 MURATA/LQP18MN56NG02D
4 2 R36, R44 RES~86.6Ω~1%~1/16W~0603 AAC/CR16-86R6FM
5 1 R45 RES~86.6Ω~1%~1/16~0402 AAC/CR05-86R6FM
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, ETC1-1-13 (Leaded)
M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 XFRM~RF~SMT~1:1CT M/A-COM, ETC1-1T (Leaded)
M/A-COM, MABAES0060 (PbF)
8 1 U2 (Lot #T23307.1) ADC~14BIT~130MSPS (D/C 0604) LINEAR/LTC2208IUP-14#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B-C
DC996B-D
1 1 C8 CAP~NPO~1.8pF~50V~0.25pF~0402 AVX/04025A1R8CAT2A
2 2 C9-C10 CAP~NPO~3.9pF~50V~0.25pF~0402 AVX/04025A3R9CAT2A
3 1 L1 IND~18nH~5%~0603 MURATA/LQP18MN18NG02D
4 2 R36, R44 RES~43.2Ω~1%~1/16W~0603 AAC/CR16-43R2FM
5 1 R45 RES~182Ω_JUMPER~0402 AAC/CR05-1820FM
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, ETC1-1-13 (Leaded)
M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 TRANSFORMER, WBC1-1L Coilcraft, WBC1-1L
8 1 U2 (Lot #T23307.1) ADC~14-BIT~130Msps (D/C 0604) LINEAR/LTC2208IUP-14#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B-D
11
dc996f
DEMO MANUAL DC996
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
DC966B-F
1 1 C8 CAP~NPO~1.8pF~50V~0.25pF 0402 AVX, 04025A1R8CAT2A
2 2 C9-10 CAP~NPO~3.9pF~50V~0.25pF 0402 AVX, 04025A3R9CAT2A
3 1 L1 IND~18nH~5% 0603 MURATA, LQP18MN18NG02D
4 2 R36, R44 RES~43.2Ω~1%~1/16W 0603 VISHAY, CRCW060343R2FKEA
5 1 R45 RES~182Ω_JUMPER 0402 VISHAY, CRCW0402182RFKED
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 TRANSFORMER, WBC1-1TL Coilcraft, WBC1-1TLC
8 1 U2 ADC~16-BIT~105Msps, LINEAR, LTC2217IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B
DC966B-G
1 1 C8 CAP~NPO~4.7pF~50V~0.25pF 0402 AVX, 04025A4R7CAT2A
2 2 C9-10 CAP~NPO~8.2pF~50V~0.25pF 0402 AVX, 04025A8R2CAT2A
3 1 L1 IND~56nH~5% 0603 MURATA, LQP18MN56NG02D
4 2 R36, R44 RES~86.6Ω~1%~1/16W 0603 VISHAY, CRCW060386R6FKEA
5 1 R45 RES~86.6Ω~1%~1/16 0402 VISHAY, CRCW040286R6FKED
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 XFRM~RF~SMT~1:1CT M/A-COM, MABAES0060 (PbF)
8 1 U2 ADC~16-BIT~80Msps LINEAR, LTC2216IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT 996B
DC966B-H
1 1 C8 CAP~NPO~1.8pF~50V~0.25pF 0402 AVX, 04025A1R8CAT2A
2 2 C9-10 CAP~NPO~3.9pF~50V~0.25pF 0402 AVX, 04025A3R9CAT2A
3 1 L1 IND~18nH~5% 0603 MURATA, LQP18MN18NG02D
4 2 R36, R44 RES~43.2Ω~1%~1/16W 0603 VISHAY, CRCW060343R2FKEA
5 1 R45 RES~182Ω_JUMPER 0402 VISHAY, CRCW0402182RFKED
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 TRANSFORMER, WBC1-1TL Coilcraft, WBC1-1TLC
8 1 U2 ADC~16-BIT~80Msps, LINEAR, LTC2216IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B
DC966B-I
1 1 C8 CAP~NPO~4.7pF~50V~0.25pF 0402 AVX, 04025A4R7CAT2A
2 2 C9-10 CAP~NPO~8.2pF~50V~0.25pF 0402 AVX, 04025A8R2CAT2A
3 1 L1 IND~56nH~5% 0603 MURATA, LQP18MN56NG02D
4 2 R36, R44 RES~86.6Ω~1%~1/16W 0603 VISHAY, CRCW060386R6FKEA
6 1 T1 (Bal to 1098A-F) BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 (Bal to 1098A-C) XFRM~RF~SMT~1:1CT M/A-COM, MABAES0060 (PbF)
8 1 U2 ADC~16-BIT~65Msps LINEAR, LTC2215IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT 996B
DC966B-J
1 1 C8 CAP~NPO~1.8pF~50V~0.25pF 0402 AVX, 04025A1R8CAT2A
2 2 C9-10 CAP~NPO~3.9pF~50V~0.25pF 0402 AVX, 04025A3R9CAT2A
3 1 L1 IND~18nH~5% 0603 MURATA, LQP18MN18NG02D
4 2 R36, R44 RES~43.2Ω~1%~1/16W 0603 VISHAY, CRCW060343R2FKEA
5 1 R45 RES~182Ω_JUMPER 0402 VISHAY, CRCW0402182RFKED
6 1 T1 BALUN~RF~SMT~1:1 M/A-COM, MABA-007159-000000 (PbF)
7 1 T2 TRANSFORMER, WBC1-1TL Coilcraft, WBC1-1TLC
8 1 U2 ADC~16-BIT~65Msps, LINEAR/LTC2215IUP#PBF
9 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT #996B
PARTS LIST
12
dc996f
DEMO MANUAL DC996
SCHEMATIC DIAGRAM
13
dc996f
DEMO MANUAL DC996
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SCHEMATIC DIAGRAM
14
dc996f
DEMO MANUAL DC996
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2012
LT 0512 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application
engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
