©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63004
MULTILAYER CERAMIC CAPACITORS/AXIAL
&RADIAL LEADED
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure.
The entire structure is
fired at high temperature to produce a monolithic
block
which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
awide range of characteristics. The EIA standard for
ceramic dielectric capacitors (RS-198) divides ceramic
dielectrics into the following classes:
Class I: Temperature compensating capacitors,
suitable for resonant circuit application or other appli-
cations where high Q and stability of capacitance char-
acteristics are required. Class I capacitors have
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
from materials which are not ferro-electric, yielding
superior stability but low volumetric efficiency.Class I
capacitors are the most stable type available, but have
the lowest volumetric efficiency.
Class II: Stable capacitors, suitable for bypass
or coupling applications or frequency discriminating
circuits where Q and stability of capacitance char-
acteristics arenot of major importance. Class II
capacitors have temperature characteristics of ± 15%
or less. They aremade from materials which are
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
temperature, voltage, frequency and time.
Class III: General purpose capacitors, suitable
for by-pass coupling or other applications in which
dielectric losses, high insulation resistance and
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
II capacitors except for temperature characteristics,
which are greater than ± 15%. Class III capacitors
have the highest vol
umetric efficiency and poorest
stability of any type.
KEMET leaded ceramic capacitors are offered in
the three most popular temperature characteristics:
C0G: Class I, with a temperature coefficient of 0 ±
30 ppm per degree C over an operating
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
X7R: Class II, with a maximum capacitance
change of ± 15% over an operating temperature
range of - 55°Cto + 125°C.
Z5U: Class III, with a maximum capacitance
change of + 22% - 56% over an operating tem-
peraturerange of + 10°Cto + 85°C.
Specified electrical limits for these three temperature
characteristics areshown in Table 1.
SPECIFIED ELECTRICAL LIMITS
Table I
C0G X7R Z5U
Dissipation Factor: Measured at following conditions.
C0G – 1 kHz and 1 vrms if capacitance >1000pF
1 MHz and 1 vrms if capacitance 1000 pF
X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Z5U – 1 kHz and 0.5 vrms
0.10%
2.5%
(3.5% @ 25V)
4.0%
Dielectric Stength: 2.5 times rated DC voltage.
Insulation Resistance (IR): At rated DC voltage,
whichever of the two is smaller
1,000 M F
or 100 G
1,000 M F
or 100 G
1,000 M F
or 10 G
Temperature Characteristics: Range, °C
Capacitance Change without
DC voltage
-55 to +125
0 ± 30 ppm/°C
-55 to +125
± 15%
+ 10 to +85
+22%,-56%
* MHz and 1 vrms if capacitance 100 pF on military product.
Parameter
Temperature Characteristics
Pass Subsequent IR Test
ELECTRICAL CHARACTERISTICS
The fundamental electrical properties of multilayer
ceramic capacitors are as follows:
Polarity: Multilayer ceramic capacitors are not polar,
and may be used with DC voltage applied in either direction.
Rated Voltage: This term refers to the maximum con-
tinuous DC working voltage permissible across the entire
operating temperature range. Multilayer ceramic capacitors
are not extremely sensitive to voltage, and brief applications
ofvoltage above rated will not result in immediate failure.
However, reliability will be reduced by exposure to sustained
voltages above rated.
Capacitance:
The standard unit of capacitance is the
farad. For practical capacitors, it is usually expressed in
microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads
(10-12 farad). Standard measurement conditions are as
follows:
Class I (up to 1,000 pF): 1MHz and 1.2 VRMS
maximum.
Class I (over 1,000 pF): 1kHz and 1.2 VRMS
maximum.
Class II: 1 kHz and 1.0 ± 0.2 VRMS.
Class III: 1 kHz and 0.5 ± 0.1 VRMS.
Like all other practical capacitors, multilayer ceramic
capacitors also have resistance and inductance. A simplified
schematic for the equivalent circuit is shown in Figure 1.
Other significant electrical characteristics resulting from
these additional properties are as follows:
Impedance: Since the parallel resistance (Rp) is nor-
mally very high, the total impedance of the capacitor is:
Figure 1
C=Capacitance
L = Inductance
RS=Equivalent Series Resistance (ESR)
RP=Insulation Resistance (IR)
RP
RS
C
L
Z =
Where Z = Total Impedance
RS = Equivalent Series Resistance
X
C
=Capacitive Reactance =
2ππfC
X
L
=Inductive Reactance = 2ππfL
1
R
S
+(X
C
- X
L
)
22
DF = ESR
Xc
Xc2πfC
1
=
Figure 2
δ
Ζ
O
Xc
ESR
The variation of a capacitor’s impedance with frequency
determines its effectiveness in many applications.
Dissipation Factor: Dissipation Factor (DF) is a mea-
sure of the losses in a capacitor under AC application. It is the
ratio of the equivalent series resistance to the capacitive reac-
tance
,and is usually expressed in percent. It is usually mea-
sured simultaneously with capacitance, and under the same
conditions. The vector diagram in Figure 2 illustrates the rela-
tionship between DF, ESR, and impedance. The reciprocal of
the dissipation factor is called the “Q”, or quality factor. For
convenience, the “Q” factor is often used for very low values
of dissipation factor. DF is sometimes called the “loss tangent”
or “tangent d”, as derived from this diagram.
Insulation Resistance: Insulation Resistance (IR) is the
DC resistance measured across the terminals of a capacitor,
represented by the parallel resistance (Rp) shown in Figure 1.
For a given dielectric type, electrode area increases with
capacitance, resulting in a decrease in the insulation resis-
tance. Consequently, insulation resistance is usually specified
as the “RC” (IR x C) product, in terms of ohm-farads or
megohm-microfarads. The insulation resistance for a specific
capacitance value is determined by dividing this product by
the capacitance. However, as the nominal capacitance values
become small, the insulation resistance calculated from the
RC product reaches values which are impractical.
Consequently, IR specifications usually include both a mini-
mum RC product and a maximum limit on the IR calculated
from that value. For example, a typical IR specification might
read “1,000 megohm-microfarads or 100 gigohms, whichever
is less.”
Insulation Resistance is the measure of a capacitor to
resist the flow of DC leakage current. It is sometimes referred
to as “leakage resistance.” The DC leakage current may be
calculated by dividing the applied voltage by the insulation
resistance (Ohm’s Law).
Dielectric Withstanding Voltage: Dielectric withstand-
ing voltage (DWV) is the peak voltage which a capacitor is
designed to withstand for short periods of time without dam-
age. All KEMET multilayer ceramic capacitors will withstand a
test voltage of 2.5 x the rated voltage for 60 seconds.
KEMET specification limits for these characteristics at
standard measurement conditions are shown in Table 1 on
page 4. Variations in these properties caused by changing
conditions of temperature, voltage, frequency, and time are
covered in the following sections.
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 5
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Application Notes
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63006
TABLE 1
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS I DIELECTRICS
Significant Figure Multiplier Applied Tolerance of
of Temperature to Temperature Temperature
Coefficient Coefficient Coefficient *
PPM per Letter Multi- Number PPM per Letter
Degree C Symbol plier Symbol Degree C Symbol
0.0 C -1 0 ±30 G
0.3 B -10 1 ±60 H
0.9 A -100 2 ±120 J
1.0 M -1000 3 ±250 K
1.5 P -100000 4 ±500 L
2.2 R +1 5 ±1000 M
3.3 S +10 6 ±2500 N
4.7 T +100 7
7.5 U +1000 8
+10000 9
*These symetrical tolerances apply to a two-point measurement of
temperature coefficient: one at 25°C and one at 85°C. Some deviation
is permitted at lower temperatures. For example, the PPM tolerance
for C0G at -55°C is +30 / -72 PPM.
TABLE 2
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS II & III DIELECTRICS
Low Temperature High Temperature Maximum Capacitance
Rating Rating Shift
Degree Letter Degree Number Letter
Celcius Symbol Celcius Symbol Percent Symbol
+10C Z +45C 2 ±1.0% A
-30C Y +65C 4 ±1.5% B
-55C X +85C 5 ±2.2% C
+105C 6±3.3% D
+125C 7 ±4.7% E
+150C 8 ±7.5% F
+200C 9±10.0% P
±15.0% R
±22.0% S
+22/-33% T
+22/-56% U
+22/-82% V
+10 +20 +30 +40 +50 +60 +70 +80
Effect of Temperature: Both capacitance and dissipa-
tion factor are affected by variations in temperature. The max-
imum capacitance change with temperatureis defined by the
temperaturecharacteristic. However,this only defines a “box”
bounded by the upper and lower operating temperatures and
the minimum and maximum capacitance values. Within this
“box”, the variation with temperature depends upon the spe-
cific dielectric formulation. Typical curves for KEMET capaci-
tors are shown in Figures 3, 4, and 5. These figures also
include the typical change in dissipation factor for KEMET
capacitors.
Insulation resistance decreases with temperature.
Typically, the insulation resistance at maximum rated temper-
atureis 10% of the 25°Cvalue.
Effect of Voltage: Class I ceramic capacitors arenot
affected by variations in applied AC or DC voltages. For Class
II and III ceramic capacitors, variations in voltage affect only
the capacitance and dissipation factor.The application of DC
voltage higher than 5 vdc reduces both the capacitance and
dissipation factor. The application of AC voltages up to 10-20
Vac tends to increase both capacitance and dissipation factor.
At higher AC voltages, both capacitance and dissipation factor
begin to decrease.
Typical curves showing the effect of applied AC and DC
voltage are shown in Figure 6 for KEMET X7R capacitors and
Figure 7 for KEMET Z5U capacitors.
Effect of Frequency: Frequency affects both capaci-
tance and dissipation factor. Typical curves for KEMET multi-
layer ceramic capacitors are shown in Figures 8 and 9.
T
he variation of impedance with frequency is an impor-
tant consideration in the application of multilayer ceramic
capacitors. Total impedance of the capacitor is the vector of the
capacitive reactance, the inductive reactance, and the ESR, as
illustrated in Figure 2. As frequency increases, the capacitive
reactance decreases. However, the series inductance (L)
shown in Figure 1 produces inductive reactance, which
increases with frequency. At some frequency, the impedance
ceases to be capacitive and becomes inductive. This point, at
the bottom of the V-shaped impedance versus frequency
curves, is the self-resonant frequency. At the self-resonant fre-
quency, the reactance is zero, and the impedance consists of
the ESR only.
Typical impedance versus frequency curves for KEMET
multilayer ceramic capacitors areshown in Figures 10, 11, and
12. These curves apply to KEMET capacitors in chip form, with-
out leads. Lead configuration and lead length have a significant
impact on the series inductance. The lead inductance is
approximately 10nH/inch, which is large compared to the
inductance of the chip. The effect of this additional inductance
is a decrease in the self-resonant frequency,and an increase
in impedance in the inductive region above the self-resonant
frequency.
Effect of Time: The capacitance of Class II and III
dielectrics change with time as well as with temperature, volt-
age and frequency. This change with time is known as “aging.”
It is caused by gradual realignment of the crystalline structure
of the ceramic dielectric material as it is cooled below its Curie
temperature, which produces a loss of capacitance with time.
The aging process is predictable and follows a logarithmic
decay.Typical aging rates for C0G, X7R, and Z5U dielectrics
areas follows:
C0G None
X7R 2.0% per decade of time
Z5U 5.0% per decade of time
Typical aging curves for X7R and Z5U dielectrics are
shown in Figure 13.
The aging process is reversible. If the capacitor is heat-
ed to a temperature above its Curie point for some period of
time, de-aging will occur and the capacitor will regain the
capacitance lost during the aging process. The amount of de-
aging depends on both the elevated temperatureand the
length of time at that temperature. Exposure to 150°C for one-
half hour or 125°C for two hours is usually sufficient to return
the capacitor to its initial value.
Because the capacitance changes rapidly immediately
after de-aging, capacitance measurements are usually delayed
for at least 10 hours after the de-aging process, which is often
referred to as the “last heat.” In addition, manufacturers utilize
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some futuretime,
to allow for customer receipt and use. Typically, the test limits
areadjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 7
Application Notes
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-63008
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dis-
sipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this sub-
ject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capac-
itors, the power dissipation capability does not depend greatly
onthe surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Power
Mounting Configuration Dissipation
ofC052 & C062
1.00" leadwiresattached to binding post 90 Celsius degrees
ofGR-1615 bridge (excellent heat sink) rise per Watt ±10%
0.25" leadwires attached to binding post 55 Celsius degrees
of GR-1615 bridge rise per Watt ±10%
Capacitor mounted flush to 0.062" glass- 77 Celsius degrees
epoxy circuit board with small copper traces rise per Watt ±10%
Capacitor mounted flush to 0.062" glass- 53 Celsius degrees
epoxy circuit board with four square inches rise per Watt ±10%
of copper land area as a heat sink
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environ-
ment. The temperature rise due to power dissipation should not
exceed 20°C. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capa-
bility into a permissible AC voltage rating. Assuming a sinu-
soidal wave form, the RMS “ripple voltage” may be calculated
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However,the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20°C.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria aremet, multilayer ceramic
capacitors may be operated with AC voltage applied without
need for DC bias.
RELIABILITY
Awell constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infi-
nite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sus-
tained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric with-
standing voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive tempera-
ture rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-
PRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These spec-
ifications and
accompanying Qualified Products List should
be consulted for details.
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are sub-
jected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MIL-
HDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50°C.
Current failure rate details for specific KEMET multilay-
er ceramic capacitor series areavailable on request.
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they aremisapplied. Typical misapplications include expo-
sure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precau-
tions include shielding of personnel and sensing for excessive
power drain during board testing.
STORAGE AND HANDLING
Ceramic chip capacitors should be stored in normal
working environments. While the chips themselves are quite
robust in other environments, solderability will be degraded
by exposureto high temperatures, high humidity, corrosive
atmospheres, and long term storage. In addition, packaging
materials will be degraded by high temperature–reels may
soften or warp, and tape peel force may increase. KEMET
recommends that maximum storage temperature not exceed
40˚ C, and maximum storage humidity not exceed 70% rela-
tive humidity. In addition, temperature fluctuations should be
minimized to avoid condensation on the parts, and atmos-
pheres should be free of chlorine and sulfur bearing com-
pounds. For optimized solderability, chip stock should be
used promptly, preferably within 1.5 years of receipt.
from the following formula:
IMPEDANCE VS FREQUENCY
Impedance (Ohms)
110100 1,000
0.001
0.01
1
10
100
0.1
0.1
Frequency - MHz
Impedance vs Frequency for C0G Dielectric
Figure 10.
EFFECT OF FREQUENCY
-0.1
0
+0.2
-0.2
+0.1
0.10
0.20
0.0
Frequency - Hertz
Capacitance & DF vs Frequency - C0G
Figure 8.
%DF
Typical Aging Rates for X7R & Z5UFigure 13.
74%
76%
78%
80%
82%
84%
86%
88%
90%
92%
94%
96%
98%
100%
Capacitance
110100 1000 10K 100K
EFFECT OF TIME
%DF
-10
-5
+5
-15
0
5.0
10.0
0.0
2.5
7.5
Frequency - Hertz
Capacitance & DF vs Frequency - X7R & Z5U
Figure 9.
.01μF.001μF
%ΔC
1001K 10K 100K1M 10M
1001K 10K 100K1M 10M
%ΔC
%ΔC
%DF
Z5U
X7R
%DF
%ΔC
Impedance (Ohms)
110100 1,000
0.001
0.01
1
10
100
0.1
0.1
Frequency - MHz
Impedance vs Frequency for Z5U Dielectric
Figure 12.
Impedance (Ohms)
110100 1,000
0.001
0.01
1
10
100
0.1
0.1
Frequency - MHz
Impedance vs Frequency for X7R Dielectric
Figure 11.
0.1μF
1.0 μF
0.1μF.01μF
1.0 μF
Impedance vs. Frequency
Leaded Ceramic C0G
0.01
0.1
1
10
100
0.1 1 1 0100 1000
Frequency - MHz
Impedance (Ohms)
0.01µF
0.001µF
Leaded X7R
0.01
0.1
1
10
100
0.1 1 1 0100 1000
Frequency - MHz
Impedance (Ohms)
0.01µF
0.1µF
Impedance vs. Frequency
1.0µF
Impedance vs. Frequency
Leaded Z5U
0.01
0.1
1
10
100
0.1 1 1 0100 1000
Frequency - MHz
Impedance (Ohms)
0.1µF
1.0µF
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
Capacitance
100%
74%
76%
78%
80%
82%
84%
86%
88%
90%
92%
94%
96%
98%
X7R
Z5U
1 10 100 1000 10K 100K
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 9
Application Notes
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
Impedance vs Frequency
for C0G Dielectric
Figure 10.
Impedance vs Frequency
for Z5U Dielectric
Figure 12.
Impedance vs Frequency
for X7R Dielectric
Figure 11.
(hours)
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630040
CERAMIC MOLDED/MIL-C-11015
& MIL-PRF-39014 (CKR)
C062 (CK06, CKR06)
Lead Dia.
.025
(+.004
-.002)
W
.026
MIN.
H
L
S
W
.045
MAX.
H
1.25
MIN.
L
S
W
H
1.25
MIN.
L
S
W
Center Line of leads within .030" of Center Line of case.
H
1.25
MIN.
S
.026
MIN.
L
C052 (CK05, CKR05) C056 (CKR05) C066 (CKR06)
Lead Dia.
.025
(+.004
-.002)
Lead Dia.
.025
(+.004
-.002)
Lead Dia.
.025
(+.004
-.002)
1.25
MIN.
****
DIMENSIONS — INCHES (MILLIMETERS)
DL
C
1.50 Min.
(38.10)
1.50 Min.
(38.10)
CAPACITOR OUTLINE DRAWINGS - (AXIAL LEADS)
CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)
CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)
DIMENSIONS — INCHES (MILLIMETERS)
*Leads are .625 minimum when tape and reel packaged.
Case
Size
Military
Equivalent Styles
L
Length
D
Body Diameter
C
Lead Diameter
C114
CK12, CKR11 .160 ± .010 (4.06 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)
C124
CK13, CCR12 .250 ± .010 (6.35 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)
C192
CK14, CKR14 .390 ± .010 (9.91 ± .25) .140 ± .010 (3.56 ± .25) .025, +.002, -.002 (.64, +.05, -.05)
C202
CK15, CKR15 .500 ± .020 (12.70 ± .51) .250 ± .015 (6.35 ± .38) .025, +.002, -.002 (.64, +.05, -.05)
C222
CK16, CKR16 .690 ± .030 (17.53 ± .76) .350 ± .020 (8.89 ± .51) .025, +.002, -.002 (.64, +.05, -.05)
Case
Size
Military
Equivalent Styles
H
Height
L
Length
W
Width
S
Lead
Spacing
C052/
C056
CK05, CKR05 .190 ± .010 (4.83 ± .25) .190 ± .010 (4.83 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)
C062/
C066
CK06, CKR06 .290 ± .010 (7.37 ± .25) .290 ± .010 (7.37 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 41
C114T (CKR11)
ORDERING INFORMATION
MARKING INFORMATION
C114T (CKR11) THROUGH C222T (CKR16) PER MIL-PRF-39014
JK
103
KP8
37A
Jfor JAN
Kfor KEMET
Capacitance
Capacitance Tolerance, FR Level
&Date Code (Year)
Week and Lot Code
C124T (CKR12)
CKR12
2657J
0837A
31433
Style
Dash No., J for JAN
Date & Lot Code
Source Code
(Federal Supply Code
for Manufacturers,
FSCM)
C192T (CKR14) C202T (CKR15) C222T (CKR16)
M39014
5-2125
KEMET
0837A
J50V
105K
Complete Part Number
Manufacturer’s Name
Date & Lot Code
JAN & Voltage
Capacitance, pF Code, Capacitance
Tolerance
C052/56T (CKR05) PER MIL-PRF-39014/01
JK
0837
A
JAN-KEMET
Date Code
Lot Code
BACK
M390
14/01
1579*
Specification
Sheet No.
Four Digit Part No.
*Add “V” as the last
digit for stand-off leads.
FRONT
C062/66T (CKR06) PER MIL-PRF-39014/02
0837A
J200V
103K
Date & Lot Code
JAN & Voltage
Capacitance, pF Code, Capacitance Tolerance
BACK
M39014
2-1338
*KEMET
Complete MIL Part No.
Manufacturer’s Name
FRONT
*Add “V” as the last digit
for stand-offleads.
C114K (CK12) THROUGH C222K (CK16) PER MIL-C-11015
C114K (CK12) C124K (CK13)
KCK
12BX
102K
0837
KEMET, CK
Style (12 or 13), Temp. Char. (BX or BR)
Capacitance, pF Code, Capacitance Tolerance
Date Code
C192K (CK14) C202K (CK15) C222K (CK16)
K100V
CK14BX
123K
0837
KEMET, Voltage
Style (14, 15 or 16), Temp. Char. (BX or BR)
Capacitance, pF Code, Capacitance Tolerance
Date Code
C052K (CK05) PER MIL-C-11015/18 & C062K (CK06) PER MIL-C-11015/19
200V
K
0801
Voltage
KEMET
Date Code
BACK
CK05
BX
102K
Style
Temperature Characteristic
Capacitance, pF Code, Capacitance Tolerance
FRONT
C 052 K 102 K 2 X 5 C A
CERAMIC
CASE SIZE
See Table Below
SPECIFICATION
Military
T – MIL-PRF-39014
K–MIL-C-11015
CAPACITANCE PICOFARAD CODE
Expressed in picofarads (pF). First two digits represent
significant figures. Third digit specifies number of zeros
following except 9 indicates division by 10). Examples:
0.1 µF = 100,000 pF = 104 and 9.1 pF = 919. See
tables for standard values.
CAPACITANCE TOLERANCE
M – ±20%
K – ±10%
WORKING VOLTAGE DC
2–200V; 1 – 100V; 5 – 50V
FAILURE RATE
A – Not Applicable
M–1.0%
P – 0.1%
R–0.01%
S – 0.001%
INTERNAL CONSTRUCTION
5 – Multilayer
TEMPERATURE CHARACTERISTIC
KEMET
Designator
Military
Equivalent
EIA
Equivalent
Cap. Change with Temp.
Temp
Range, °C
Measured
without DC
Bias Voltage
Measured
with Bias
(Rated
Voltage)
X
(Stable) BX X7R -55 to
+125° ±15% +15%
-25%
R
(Stable) BR X7R -55° to
+125 ±15% +15%
-40%
Standard tolerances for each Series
are shown in the repetitive parts lists.
Case Sizes
Radial Axial
C052 C114
C056 C124
C062 C192
C066 C202
C222
Part Number Example: C052K102K2X5CA (14 digits – no spaces)
MIL-C-11015
MIL-PRF-39014
CERAMIC MOLDED/MIL-C-11015
& MIL-PRF-39014 (CKR)
LEAD MATERIAL
C–60/40 Tin/Lead (SnPb)
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630042
CERAMIC MOLDED/AXIAL — MIL-C-11015
&MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)
RATINGS & PART NUMBER REFERENCE
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P—.1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
M P R S
10 10 C114(1)100K1X5C(2) CK12BX100K CKR11BX100K(2) 2601 2801 2001 2201
10 20 C114(1)100M1X5C(2) CK12BX100M CKR11BX100M(2) 2602 2802 2002 2202
12 10 C114(1)120K1X5C(2) CK12BX120K CKR11BX120K(2) 2603 2803 2003 2203
1510C114(1)150K1X5C(2) CK12BX120K CKR11BX150K(2) 2604 2804 2004 2204
15 20 C114(1)150M1X5C(2) CK12BX150M CKR11BX150M(2) 2605 2805 2005 2205
18 10 C114(1)180K1X5C(2) CK12BX180K CKR11BX180K(2) 2606 2806 2006 2206
22 10 C114(1)220K1X5C(2) CK12BX220K CKR11BX220K(2) 2607 2807 2007 2207
22 20 C114(1)220M1X5C(2) CK12BX220M CKR11BX220M(2) 2608 2808 2008 2208
27 10 C114(1)270K1X5C(2) CK12BX270K CKR11BX270K(2) 2609 2809 2009 2209
33 10 C114(1)330K1X5C(2) CK12BX330K CKR11BX330K(2) 2610 2810 2010 2210
33 20 C114(1)330M1X5C(2) CK12BX330M CKR11BX330M(2) 2611 2811 2011 2211
39 10 C114(1)390K1X5C(2) CK12BX390K CKR11BX390K(2) 2612 2812 2012 2212
4710C114(1)470K1X5C(2) CK12BX470K CKR11BX470K(2) 2613 2813 2013 2213
47 20 C114(1)470M1X5C(2) CK12BX470M CKR11BX470M(2) 2614 2814 2014 2214
56 10 C114(1)560K1X5C(2) CK12BX560K CKR11BX560K(2) 2615 2815 2015 2215
68 10 C114(1)680K1X5C(2) CK12BX680K CKR11BX560K(2) 2616 2816 2016 2216
68 20 C114(1)680M1X5C(2) CK12BX680M CKR11BX680M(2) 2617 2817 2017 2217
82 10 C114(1)820K1X5C(2) CK12BX820K CKR11BX820K(2) 2618 2818 2018 2218
100 10 C114(1)101K1X5C(2) CK12BX102K CKR11BX102K(2) 2619 2819 2019 2219
100 20 C114(1)101M1X5C(2) CK12BX102M CKR11BX102M(2) 2620 2820 2020 2220
120 10 C114(1)121K1X5C(2) CK12BX121K CKR11BX121K(2) 2621 2821 2021 2221
150 10 C114(1)151K1X5C(2) CK12BX151K CKR11BX151K(2) 2622 2822 2022 2222
150 20 C114(1)151M1X5C(2) CK12BX151M CKR11BX151M(2) 2623 2823 2023 2223
180 10 C114(1)181K1X5C(2) CK12BX181K CKR11BX181K(2) 2624 2824 2024 2224
220 10 C114(1)221K1X5C(2) CK12BX221K CKR11BX221K(2) 2625 2825 2025 2225
220 20 C114(1)221M1X5C(2) CK12BX221M CKR11BX221K(2) 2626 2826 2026 2226
270 10 C114(1)271K1X5C(2) CK12BX271K CKR11BX271K(2) 2627 2827 2027 2227
330 10 C114(1)331K1X5C(2) CK12BX331K CKR11BX331K(2) 2628 2828 2028 2228
330 20C114(1)331M1X5C(2) CK12BX331M CKR11BX331M(2) 2629 2829 2029 2229
390 10 C114(1)391K1X5C(2) CK12BX391K CKR11BX391K(2) 2630 2830 2030 2230
470 10 C114(1)471K1X5C(2) CK12BX471K CKR11BX471K(2) 2631 2831 2031 2231
470 20 C114(1)471M1X5C(2) CK12BX471M CKR11BX471M(2) 2632 2832 2032 2232
560 10 C114(1)561K1X5C(2) CK12BX561K CKR11BX561K(2) 2633 2833 2033 2233
680 10 C114(1)681K1X5C(2) CK12BX681K CKR11BX561K(2) 2634 2834 2034 2234
680 20 C114(1)681M1X5C(2) CK12BX681M CKR11BX681M(2) 2635 2835 2035 2235
820 10 C114(1)821K1X5C(2) CK12BX821K CKR11BX821K(2) 2636 2836 2036 2236
1,000 10 C114(1)102K1X5C(2) CK12BX102K CKR11BX102K(2) 2637 2837 2037 2237
1,000 20 C114(1)102M1X5C(2) CK12BX102M CKR11BX102M(2) 2638 2838 2038 2238
1,200 10 C114(1)122K1X5C(2) CK12BX122K CKR11BX122K(2) 2639 2839 2039 2239
1,500 10 C114(1)152K1X5C(2) CK12BX152K CKR11BX152K(2) 2640 2840 2040 2240
1,500 20 C114(1)152M1X5C(2) CK12BX152M CKR11BX152M(2) 2641 2841 2041 2241
1,800 10 C114(1)182K1X5C(2) CK12BX182K CKR11BX182K(2) 2642 2842 2042 2242
2,200 10 C114(1)222K1X5C(2) CK12BX222K CKR11BX222K(2) 2643 2843 2043 2243
2,200 20 C114(1)222M1X5C(2) CK12BX222M CKR11BX222M(2) 2644 2844 2044 2244
2,700 10 C114(1)272K1X5C(2) CK12BX272K CKR11BX272K(2) 2645 2845 2045 2245
3,300 10 C114(1)332K1X5C(2) CK12BX332K CKR11BX332K(2) 2646 2846 2046 2246
3,300 20 C114(1)332M1X5C(2) CK12BX332M CKR11BX332M(2) 2647 2847 2047 2247
3,900 10 C114(1)392K1X5C(2) CK12BX392K CKR11BX392K(2) 2648 2848 2048 2248
4,700 10 C114(1)472K1X5C(2) CK12BX472K CKR11BX472K(2) 2649 2849 2049 2249
4,700 20 C114(1)472M1X5C(2) CK12BX472M CKR11BX472M(2) 2650 2850 2050 2250
5,600 10 C114(1)562K5X5C(2) CK12BX562K CKR11BX562K(2) 2651 2851 2051 2251
6,800 10 C114(1)682K5X5C(2) CK12BX682K CKR11BX682K(2) 2652 2852 2052 2252
6,800 20 C114(1)682M5X5C(2) CK12BX682M CKR11BX682M(2) 2653 2853 2053 2253
8,200 10 C114(1)822K5X5C(2) CK12BX822K CKR11BX822K(2) 2654 2854 2054 2254
10,000 10 C114(1)103K5X5C(2) CK12BX103K CKR11BX103K(2) 2655 2855 2055 2255
10,000 20 C114(1)103M5X5C(2) CK12BX103M CKR11BX103M(2) 2656 2856 2056 2256
5,600 10 C124(1)562K1X5C(2) CK13BX562K CKR12BX562K(2) 2657 2857 2057 2257
6,800 10 C124(1)682K1X5C(2) CK13BX682K CKR12BX682K(2) 2658 2858 2058 2258
6,800 20 C124(1)682M1X5C(2) CK13BX682M CKR12BX682M(2) 2659 2859 2059 2259
8,200 10 C124(1)822K1X5C(2) CK13BX822K CKR12BX822K(2) 2660 2860 2060 2260
10,000 10 C124(1)103K1X5C(2) CK13BX103K CKR12BX103K(2) 2661 2861 2061 2261
10,000 20 C124(1)103M1X5C(2) CK13BX103M CKR12BX103M(2) 2662 2862 2062 2262
12,000 10 C124(1)123K5X5C(2) CK13BX123K CKR12BX123K(2) 2663 2863 2063 2263
15,000 10 C124(1)153K5X5C(2) CK13BX153K CKR12BX153K(2) 2664 2864 2064 2264
15,000 20 C124(1)153M5X5C(2) CK13BX153M CKR12BX153M(2) 2665 2865 2065 2265
18,000 10 C124(1)183K5X5C(2) CK13BX183K CKR12BX183K(2) 2666 2866 2066 2266
22,000 10 C124(1)183K5X5C(2) CK13BX223K CKR12BX223K(2) 2667 2861 2061 2261
22,000 20 C124(1)223M5X5C(2) CK13BX223M CKR12BX223M(2) 2668 2868 2068 2268
27,000 10 C124(1)273K5X5C(2) CK13BX273K
33,000 10 C124(1)333K5X5C(2) CK13BX333K
33,000 20 C124(1)333M5X5C(2) CK13BX333M
39,000 10 C124(1)393K5X5C(2) CK13BX393K
47,000 10 C124(1)473K5X5C(2) CK13BX473K
47,000 20 C124(1)473M5X5C(2) CK13BX473M
50 VOLT – C114 SIZE (MILITARY-CK12 or CKR11)
100 VOLT – C124 SIZE (MILITARY-CK13 or CKR12)
50 VOLT – C124 SIZE (MILITARY-CK13 or CKR12)
MIL-PRF-39014/05 For Failure
Rate Levels (2)
100 VOLT – C114 SIZE (MILITARY-CK12 or CKR11)
CAP.
pF
TOL.
%
KEMET
PART NUMBER
MIL-C-11015/02
MIL-PRF-39014/05
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 43
RATINGS & PART NUMBER REFERENCE
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P—.1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
MIL-C-11015
MIL-PRF-39014
CERAMIC MOLDED/AXIAL — MIL-C-11015
&MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)
M P R S
27,000 10 C124T273K5X5C(2) CKR12BX273K(2) 2669 2869 2069 2269
33,000 10 C124T333K5X5C(2) CKR12BX333K(2) 2670 2870 2070 2270
33,000 20 C124T333M5X5C(2) CKR12BX333M(2) 2671 2871 2071 2271
39,000 10C124T393K5X5C(2) CKR12BX393K(2) 2672 2872 2072 2272
47,000 10 C124T473K5X5C(2) CKR12BX473K(2) 2673 2873 2073 2273
47,000 20C124T473M5X5C(2) CKR12BX473M(2) 2674 2874 2074 2274
12,000 10 C192(1)123K1X5C(2) CK14BX123K CKR14BX123K(2) 2675 2875 2075 2275
15,000 10C192(1)153K1X5C(2) CK14BX153K CKR14BX153K(2) 2676 2876 2076 2276
15,000 20 C192(1)153M1X5C(2) CK14BX153M CKR14BX153M(2) 2677 2877 2077 2277
18,000 10 C192(1)183K1X5C(2) CK14BX183K CKR14BX183K(2) 2678 2878 2078 2278
22,000 10C192(1)223K1X5C(2) CK14BX223K CKR14BX223K(2) 2679 2879 2079 2279
22,000 20C192(1)223M1X5C(2) CK14BX223M CKR14BX223M(2) 2680 2880 2080 2280
27,000 10 C192(1)273K1X5C(2) CK14BX273K CKR14BX273K(2) 2681 2881 2081 2281
33,000 10 C192(1)333K1X5C(2) CK14BX333K CKR14BX333K(2) 2682 2882 2082 2282
33,000 20C192(1)333M1X5C(2) CK14BX333M CKR14BX333M(2) 2683 2883 2083 2283
39,000 10 C192(1)393K1X5C(2) CK14BX393K CKR14BX393K(2) 2684 2884 2084 2284
47,000 10 C192(1)473K1X5C(2) CK14BX473K CKR14BX473K(2) 2685 2885 2085 2285
47,000 20 C192(1)473M1X5C(2) CK14BX473M CKR14BX473M(2) 2686 2886 2086 2286
56,000 10C192(1)563K1X5C(2) CK14BR563K CKR14BR563K(2) 2693 2893 2093 2293
68,000 10 C192(1)683K1X5C(2) CK14BR683K CKR14BR683K(2) 2694 2894 2094 2294
68,000 20 C192(1)683M1X5C(2) CK14BR683M CKR14BR683M(2) 2695 2895 2095 2295
82,000 10 C192(1)823K1X5C(2) CK14BR823K CKR14BR823K(2) 2696 2896 2096 2296
100,000 10 C192(1)104K1X5C(2) CK14BR104K CKR14BR104K(2) 2697 2897 2097 2297
100,000 20C192(1)104M1X5C(2) CK14BR104M CKR14BR104M(2) 2698 2898 2098 2298
56,000 10 C192T563K5X5C(2) CKR14BX563K(2) 2687 2887 2087 2287
68,000 10 C192T683K5X5C(2) CKR14BX683K(2) 2688 2888 2088 2288
68,000 20 C192T683M5X5C(2) CKR14BX683M(2) 2689 2889 2089 2289
82,000 10C192T823K5X5C(2) CKR14BX823K(2) 2690 2890 2090 2290
100,000 10 C192T104K5X5C(2) CKR14BX104K(2) 2691 2891 2091 2291
100,000 20C192T104M5X5C(2) CKR14BX104M(2) 2692 2892 2092 2292
120,000 10 C192(1)124K5X5C(2) CK14BR124K CKR14BX124K(2) 2699 2899 2099 2299
150,000 10 C192(1)154K5X5C(2) CK14BR154K CKR14BX154K(2) 2700 2900 2100 2300
150,000 20 C192(1)154M5X5C(2) CK14BR154M CKR14BX154M(2) 2701 2901 2101 2301
180,000 10 C192(1)184K5X5C(2) CK14BR184K CKR14BX184K(2) 2702 2902 2102 2302
220,000 10 C192(1)224K5X5C(2) CK14BR224K CKR14BX224K(2) 2703 2903 2103 2303
220,000 20 C192(1)224M5X5C(2) CK14BR224M CKR14BX224M(2) 2704 2904 2104 2304
270,000 10 C192(1)274K5X5C(2) CK14BR274K CKR14BX274K(2) 2705 2905 2105 2305
56,000 10 C202T563K1X5C(2) CKR15BX563K(2) 2706 2906 2106 2306
68,000 10 C202T683K1X5C(2) CKR15BX683K(2) 2707 2907 2107 2307
68,000 20 C202T683M1X5C(2) CKR15BX683K(2) 2708 2908 2108 2308
82,000 10 C202T823K1X5C(2) CKR15BX823K(2) 2709 2909 2109 2309
100,000 10 C202(1)104K1X5C(2) CK15BX104K CKR15BX104K(2) 2710 2910 2110 2310
100,000 20 C202(1)104M1X5C(2) CK15BX104M CKR15BX104M(2) 2711 2911 2111 2311
120,000 10 C202(1)124K1R5C(2) CK15BR124K CKR15BR124K(2) 2712 2912 2112 2312
150,000 10 C202(1)154K1R5C(2) CK15BR154K CKR15BR154K(2) 2713 2913 2113 2313
150,000 20 C202(1)154M1R5C(2) CK15BR154M CKR15BR154M(2) 2714 2914 2114 2314
180,000 10 C202(1)184K1R5C(2) CK15BR184K CKR15BR184K(2) 2715 2915 2115 2315
220,000 10 C202(1)224K1R5C(2) CK15BR224K CKR15BR224K(2) 2716 2916 2116 2316
220,000 20 C202(1)224M1R5C(2) CK15BR224M CKR15BR224M(2) 2717 2917 2117 2317
270,000 10 C202(1)274K1R5C(2) CK15BR274K CKR15BR274K(2) 2718 2918 2118 2318
330,000 10 C202(1)334K1R5C(2) CK15BR334K CKR15BR334K(2) 2719 2919 2119 2319
330,000 20 C202(1)334M1R5C(2) CK15BR334M CKR15BR334M(2) 2720 2920 2120 2320
470,000 10 C202(1)474K5R5C(2) CK15BR474K CKR15BR474K(2) 2721 2921 2121 2321
470,000 20 C202(1)474M5R5C(2) CK15BR474M CKR15BR474M(2) 2722 2922 2122 2322
680,000 10 C202T684K5R5C(2) CKR15BR684K(2) 2723 2923 2123 2323
680,000 20 C202T684M5R5C(2) CKR15BR684M(2) 2724 2924 2124 2324
1,000,000 10 C202(1)105K5R5C(2) CK15BR105K CKR15BR105K(2) 2725 2925 2125 2325
1,000,000 20 C202(1)105M5R5C(2) CK15BR105M CKR15BR105M(2) 2726 2926 2126 2326
470,000 10 C222(1)474K1R5C(2) CK16BR474K CKR16BR474K(2) 2727 2927 2127 2327
470,000 20 C222(1)474M1R5C(2) CK16BR474M CKR16BR474M(2) 2728 2928 2128 2328
680,000 10 C222(1)684K1R5C(2) CKR16BR684K(2) 2729 2929 2129 2329
680,000 20 C222(1)684M1R5C(2) CKR16BR684M(2) 2730 2930 2130 2330
1,000,000 10 C222(1)105K1R5C(2) CK16BR105K CKR16BR105K(2) 2731 2931 2131 2331
1,000,000 20 C222(1)105M1R5C(2) CK16BR105M CKR16BR105M(2) 2732 2932 2132 2332
2,200,000 10 C222(1)225K5R5C(2) CK16BR225K CKR16BR225K(2) 2733 2933 2133 2333
2,200,000 20 C222(1)225M5R5C(2) CK16BR225M CKR16BR225M(2) 2734 2934 2134 2334
3,300,000 10 C222(1)335K5R5C(2) CK16BR335K CKR16BR335K(2) 2735 2935 2135 2335
3,300,000 20 C222(1)335M5R5C(2) CK16BR335M CKR16BR335M(2) 2736 2936 2136 2336
100 VOLT – C192 SIZE (MILITARY-CK14 or CKR14)
50 VOLT – C192 SIZE (MILITARY-CK14 or CKR14)
50 VOLT – C222 SIZE (MILITARY-CK16 or CKR16)
100 VOLT – C222 SIZE (MILITARY-CK16 or CKR16)
100 VOLT – C202 SIZE (MILITARY-CK15 or CKR15)
50 VOLT – C202 SIZE (MILITARY-CK15 or CKR15)
MIL-PRF-39014/05 For Failure
Rate Levels (2)
50 VOLT – C124 SIZE (MILITARY-CK13 or CKR12)(continued)
CAP.
pF
TOL.
%
KEMET
PART NUMBER
MIL-C-11015/02
MIL-PRF-39014/05
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630044
CERAMIC MOLDED/RADIAL — MIL-C-11015
&MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,
P—.1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
(3) Insert “V” for standard design (C056). Leave blank for the flat bottom design (C052).
(4) Insert “2” for standard design (Style C052) Note: Stand-offs are available only
Insert “6” for stand-off design (Style C056) with the CKR, not the CK.
}
RATINGS & PART NUMBER REFERENCE
M P R S
10 10 C05(4)(1)100K2X5C(2) CK05BX100K CKR05BX100K(2)(3) 1201(3) 1241(3) 1281(3) 1321(3)
10 20 C05(4)(1)100M2X5C(2) CK05BX100M CKR05BX100M(2)(3) 1202(3) 1242(3) 1282(3) 1322(3)
1210C05(4)(1)120K2X5C(2) CK05BX120K CKR05BX120K(2)(3) 1203(3) 1243(3) 1283(3) 1323(3)
15 10 C05(4)(1)150K2X5C(2) CK05BX150K CKR05BX150K(2)(3) 1204(3) 1244(3) 1284(3) 1324(3)
15 20 C05(4)(1)150M2X5C(2) CK05BX150M CKR05BX150M(2)(3) 1205(3) 1245(3) 1285(3) 1325(3)
1810C05(4)(1)180K2X5C(2) CK05BX180K CKR05BX180K(2)(3) 1206(3) 1246(3) 1286(3) 1326(3)
2210C05(4)(1)220K2X5C(2) CK05BX220K CKR05BX220K(2)(3) 1207(3) 1247(3) 1287(3) 1327(3)
22 20 C05(4)(1)220M2X5C(2) CK05BX220M CKR05BX220M(2)(3) 1208(3) 1248(3) 1288(3) 1328(3)
27 10 C05(4)(1)270K2X5C(2) CK05BX270K CKR05BX270K(2)(3) 1209(3) 1249(3) 1289(3) 1329(3)
33 10 C05(4)(1)330K2X5C(2) CK05BX330K CKR05BX330K(2)(3) 1210(3) 1250(3) 1290(3) 1330(3)
33 20 C05(4)(1)330M2X5C(2) CK05BX330M CKR05BX330M(2)(3) 1211(3) 1251(3) 1291(3) 1331(3)
3910C05(4)(1)390K2X5C(2) CK05BX390K CKR05BX390K(2)(3) 1212(3) 1252(3) 1292(3) 1332(3)
4710C05(4)(1)470K2X5C(2) CK05BX470K CKR05BX470K(2)(3) 1213(3) 1253(3) 1293(3) 1333(3)
47 20 C05(4)(1)470M2X5C(2) CK05BX470M CKR05BX470M(2)(3) 1214(3) 1254(3) 1294(3) 1334(3)
56 10 C05(4)(1)560K2X5C(2) CK05BX560K CKR05BX560K(2)(3) 1215(3) 1255(3) 1295(3) 1335(3)
68 10 C05(4)(1)680K2X5C(2) CK05BX680K CKR05BX680K(2)(3) 1216(3) 1256(3) 1296(3) 1336(3)
68 20 C05(4)(1)680M2X5C(2) CK05BX680M CKR05BX680M(2)(3) 1217(3) 1257(3) 1297(3) 1337(3)
8210C05(4)(1)820K2X5C(2) CK05BX820K CKR05BX820K(2)(3) 1218(3) 1258(3) 1298(3) 1338(3)
100 10C05(4)(1)101K2X5C(2) CK05BX101K CKR05BX101K(2)(3) 1219(3) 1259(3) 1299(3) 1339(3)
100 20 C05(4)(1)101M2X5C(2) CK05BX101M CKR05BX101M(2)(3) 1220(3) 1260(3) 1300(3) 1340(3)
120 10 C05(4)(1)121K2X5C(2) CK05BX121K CKR05BX121K(2)(3) 1221(3) 1261(3) 1301(3) 1341(3)
150 10C05(4)(1)151K2X5C(2) CK05BX151K CKR05BX151K(2)(3) 1222(3) 1262(3) 1302(3) 1342(3)
150 20 C05(4)(1)151M2X5C(2) CK05BX151M CKR05BX151M(2)(3) 1223(3) 1263(3) 1303(3) 1343(3)
180 10 C05(4)(1)181K2X5C(2) CK05BX181K CKR05BX181K(2)(3) 1224(3) 1264(3) 1304(3) 1344(3)
220 10 C05(4)(1)221K2X5C(2) CK05BX221K CKR05BX221K(2)(3) 1225(3) 1265(3) 1305(3) 1345(3)
220 20 C05(4)(1)221M2X5C(2) CK05BX221M CKR05BX221M(2)(3) 1226(3) 1266(3) 1306(3) 1346(3)
270 10C05(4)(1)271K2X5C(2) CK05BX271K CKR05BX271K(2)(3) 1227(3) 1267(3) 1307(3) 1347(3)
330 10C05(4)(1)331K2X5C(2) CK05BX331K CKR05BX331K(2)(3) 1228(3) 1268(3) 1308(3) 1348(3)
330 20 C05(4)(1)331M2X5C(2) CK05BX331M CKR05BX331M(2)(3) 1229(3) 1269(3) 1309(3) 1349(3)
390 10 C05(4)(1)391K2X5C(2) CK05BX391K CKR05BX391K(2)(3) 1230(3) 1270(3) 1310(3) 1350(3)
470 10 C05(4)(1)471K2X5C(2) CK05BX471K CKR05BX471K(2)(3) 1231(3) 1271(3) 1311(3) 1351(3)
470 20 C05(4)(1)471M2X5C(2) CK05BX471M CKR05BX471M(2)(3) 1232(3) 1272(3) 1312(3) 1352(3)
560 10 C05(4)(1)561K2X5C(2) CK05BX561K CKR05BX561K(2)(3) 1233(3) 1273(3) 1313(3) 1353(3)
680 10C05(4)(1)681K2X5C(2) CK05BX681K CKR05BX681K(2)(3) 1234(3) 1274(3) 1314(3) 1354(3)
680 20 C05(4)(1)681M2X5C(2) CK05BX681M CKR05BX681M(2)(3) 1235(3) 1275(3) 1315(3) 1355(3)
820 10 C05(4)(1)821K2X5C(2) CK05BX821K CKR05BX821K(2)(3) 1236(3) 1276(3) 1316(3) 1356(3)
1,000 10 C05(4)(1)102K2X5C(2) CK05BX102K CKR05BX102K(2)(3) 1237(3) 1277(3) 1317(3) 1357(3)
1,000 20 C05(4)(1)102M2X5C(2) CK05BX102M CKR05BX102M(2)(3) 1238(3) 1278(3) 1318(3) 1358(3)
1,200 10 C05(4)(1)122K1X5C(2) CK05BX122K CKR05BX122K(2)(3) 1239(3) 1279(3) 1319(3) 1359(3)
1,500 10 C05(4)(1)152K1X5C(2) CK05BX152K CKR05BX152K(2)(3) 1240(3) 1280(3) 1320(3) 1360(3)
1,500 20 C05(4)(1)152M1X5C(2) CK05BX152M CKR05BX152M(2)(3) 1441(3) 1481(3) 1521(3) 1561(3)
1,800 10 C05(4)(1)182K1X5C(2) CK05BX182K CKR05BX182K(2)(3) 1442(3) 1482(3) 1522(3) 1562(3)
2,200 10 C05(4)(1)222K1X5C(2) CK05BX222K CKR05BX222K(2)(3) 1443(3) 1483(3) 1523(3) 1563(3)
2,200 20 C05(4)(1)222M1X5C(2) CK05BX222M CKR05BX222M(2)(3) 1444(3) 1484(3) 1524(3) 1564(3)
2,700 10 C05(4)(1)272K1X5C(2) CK05BX272K CKR05BX272K(2)(3) 1445(3) 1485(3) 1525(3) 1565(3)
3,300 10 C05(4)(1)332K1X5C(2) CK05BX332K CKR05BX332K(2)(3) 1446(3) 1486(3) 1526(3) 1566(3)
3,300 20 C05(4)(1)332M1X5C(2) CK05BX332M CKR05BX332M(2)(3) 1447(3) 1487(3) 1527(3) 1567(3)
3,900 10 C05(4)(1)392K1X5C(2) CK05BX392K CKR05BX392K(2)(3) 1448(3) 1488(3) 1528(3) 1568(3)
4,700 10 C05(4)(1)472K1X5C(2) CK05BX472K CKR05BX472K(2)(3) 1449(3) 1489(3) 1529(3) 1569(3)
4,700 20 C05(4)(1)472M1X5C(2) CK05BX472M CKR05BX472M(2)(3) 1450(3) 1490(3) 1530(3) 1570(3)
5,600 10 C05(4)(1)562K1X5C(2) CK05BX562K CKR05BX562K(2)(3) 1451(3) 1491(3) 1531(3) 1571(3)
6,800 10 C05(4)(1)682K1X5C(2) CK05BX682K CKR05BX682K(2)(3) 1452(3) 1492(3) 1532(3) 1572(3)
6,800 20 C05(4)(1)682M1X5C(2) CK05BX682M CKR05BX682M(2)(3) 1453(3) 1493(3) 1533(3) 1573(3)
8,200 10 C05(4)(1)822K1X5C(2) CK05BX822K CKR05BX822K(2)(3) 1454(3) 1494(3) 1534(3) 1574(3)
10,000 10 C05(4)(1)103K1X5C(2) CK05BX103K CKR05BX103K(2)(3) 1455(3) 1495(3) 1535(3) 1575(3)
10,000 20 C05(4)(1)103M1X5C(2) CK05BX103M CKR05BX103M(2)(3) 1456(3) 1496(3) 1536(3) 1576(3)
12,000 10 C05(4)(1)123K5X5C(2) CK05BX123K CKR05BX123K(2)(3) 1457(3) 1497(3) 1537(3) 1577(3)
15,000 10 C05(4)(1)153K5X5C(2) CK05BX153K CKR05BX153K(2)(3) 1458(3) 1498(3) 1538(3) 1578(3)
15,000 20 C05(4)(1)153M5X5C(2) CK05BX153M CKR05BX153M(2)(3) 1459(3) 1499(3) 1539(3) 1579(3)
18,000 10 C05(4)(1)183K5X5C(2) CK05BX183K CKR05BX183K(2)(3) 1460(3) 1500(3) 1540(3) 1580(3)
22,000 10 C05(4)(1)223K5X5C(2) CK05BX223K CKR05BX223K(2)(3) 1461(3) 1501(3) 1541(3) 1581(3)
22,000 20 C05(4)(1)223M5X5C(2) CK05BX223M CKR05BX223M(2)(3) 1462(3) 1502(3) 1542(3) 1582(3)
27,000 10 C05(4)(1)273K5X5C(2) CK05BX273K CKR05BX273K(2)(3) 1463(3) 1503(3) 1543(3) 1583(3)
33,000 10 C05(4)(1)333K5X5C(2) CK05BX333K CKR05BX333K(2)(3) 1464(3) 1504(3) 1544(3) 1584(3)
33,000 20 C05(4)(1)333M5X5C(2) CK05BX333M CKR05BX333M(2)(3) 1465(3) 1505(3) 1545(3) 1585(3)
39,000 10 C05(4)(1)393K5X5C(2) CK05BX393K CKR05BX393K(2)(3) 1466(3) 1506(3) 1546(3) 1586(3)
47,000 10 C05(4)(1)473K5X5C(2) CK05BX473K CKR05BX473K(2)(3) 1467(3) 1507(3) 1547(3) 1587(3)
47,000 20 C05(4)(1)473M5X5C(2) CK05BX473M CKR05BX473M(2)(3) 1468(3) 1508(3) 1548(3) 1588(3)
56,000 10 C05(4)(1)563K5X5C(2) CK05BX563K CKR05BX563K(2)(3) 1469(3) 1509(3) 1549(3) 1589(3)
68,000 10 C05(4)(1)683K5X5C(2) CK05BX683K CKR05BX683K(2)(3) 1470(3) 1510(3) 1550(3) 1590(3)
68,000 20 C05(4)(1)683M5X5C(2) CK05BX683M CKR05BX683M(2)(3) 1471(3) 1511(3) 1551(3) 1591(3)
82,000 10 C05(4)(1)823K5X5C(2) CK05BX823K CKR05BX823K(2)(3) 1472(3) 1512(3) 1552(3) 1592(3)
100,000 10 C05(4)(1)104K5X5C(2) CK05BX104K CKR05BX104K(2)(3) 1473(3) 1513(3) 1553(3) 1593(3)
100,000 20 C05(4)(1)104M5X5C(2) CK05BX104M CKR05BX104M(2)(3) 1474(3) 1514(3) 1554(3) 1594(3)
100 VOLT – C052/C056 SIZE (MILITARY-CK05 or CKR05)
50 VOLT – C052/C056 SIZE (MILITARY-CK05 or CKR05)
MIL-PRF-39014/01 For Failure
Rate Levels (2)
200 VOLT – C052/C056 SIZE (MILITARY-CK05 or CKR05)
CAP.
pF
TOL.
%
KEMET
PART NUMBER
MIL-C-11015/18
MIL-PRF-39014/01
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 45
RATINGS & PART NUMBER REFERENCE
(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014.
(2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours, P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)
(3) Add “V” for stand-off design (C066). Leave blank for the flat bottom design (C062).
(4) Insert “2” for standarddesign (Style C062). Insert “6” for stand-off design (Style C066). Note: Stand-offs are available only with the CKR, not the CK.
MIL-C-11015
MIL-PRF-39014
CERAMIC MOLDED/AXIAL — MIL-C-11015
&MIL-PRF-39014
STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)
M P R S
1,200 10 C06(4)(1)122K2X5C(2) CK06BX122K CKR06BX122K(2)(3) 1201(3) 1241(3) 1281(3) 1321(3)
1,500 10 C06(4)(1)152K2X5C(2) CK06BX152K CKR06BX152K(2)(3) 1202(3) 1242(3) 1282(3) 1322(3)
1,500 20C06(4)(1)152M2X5C(2) CK06BX152M CKR06BX152M(2)(3) 1203(3) 1243(3) 1283(3) 1323(3)
1,800 10 C06(4)(1)182K2X5C(2) CK06BX182K CKR06BX182K(2)(3) 1204(3) 1244(3) 1284(3) 1324(3)
2,200 10 C06(4)(1)222K2X5C(2) CK06BX222K CKR06BX222K(2)(3) 1206(3) 1246(3) 1286(3) 1326(3)
2,200 20C06(4)(1)222M2X5C(2) CK06BX222M CKR06BX222M(2)(3) 1207(3) 1247(3) 1287(3) 1327(3)
2,700 10 C06(4)(1)272K2X5C(2) CK06BX272K CKR06BX272K(2)(3) 1208(3) 1248(3) 1288(3) 1328(3)
3,300 10 C06(4)(1)332K2X5C(2) CK06BX332K CKR06BX332K(2)(3) 1209(3) 1249(3) 1289(3) 1329(3)
3,300 20C06(4)(1)332M2X5C(2) CK06BX332M CKR06BX332M(2)(3) 1210(3) 1250(3) 1290(3) 1330(3)
3,900 10 C06(4)(1)392K2X5C(2) CK06BX392K CKR06BX392K(2)(3) 1211(3) 1251(3) 1291(3) 1331(3)
4,700 10 C06(4)(1)472K2X5C(2) CK06BX472K CKR06BX472K(2)(3) 1212(3) 1252(3) 1292(3) 1332(3)
4,700 20C06(4)(1)472M2X5C(2) CK06BX472M CKR06BX472M(2)(3) 1213(3) 1253(3) 1293(3) 1333(3)
5,600 10 C06(4)(1)562K2X5C(2) CK06BX562K CKR06BX562K(2)(3) 1214(3) 1254(3) 1294(3) 1334(3)
6,800 10 C06(4)(1)682K2X5C(2) CK06BX682K CKR06BX682K(2)(3) 1215(3) 1255(3) 1295(3) 1335(3)
6,800 20C06(4)(1)682M2X5C(2) CK06BX682M CKR06BX682M(2)(3) 1216(3) 1256(3) 1296(3) 1336(3)
8,200 10 C06(4)(1)822K2X5C(2) CK06BX822K CKR06BX822K(2)(3) 1217(3) 1257(3) 1297(3) 1337(3)
10,000 10 C06(4)(1)103K2X5C(2) CK06BX103K CKR06BX103K(2)(3) 1218(3) 1258(3) 1298(3) 1338(3)
10,000 20C06(4)(1)103M2X5C(2) CK06BX103M CKR06BX103M(2)(3) 1219(3) 1259(3) 1299(3) 1339(3)
12,000 10 C06(4)(1)123K1X5C(2) CK06BX123K CKR06BX123K(2)(3) 1231(3) 1271(3) 1311(3) 1351(3)
15,000 10C06(4)(1)153K1X5C(2) CK06BX153K CKR06BX153K(2)(3) 1220(3) 1260(3) 1300(3) 1340(3)
15,000 20 C062K153M1X5CA CK06BX153M
18,000 10 C06(4)(1)183K1X5C(2) CK06BX183K CKR06BX183K(2)(3) 1221(3) 1261(3) 1301(3) 1341(3)
22,000 10C06(4)(1)223K1X5C(2) CK06BX223K CKR06BX223K(2)(3) 1222(3) 1262(3) 1302(3) 1342(3)
22,000 20 C062K223M1X5CA CK06BX223M
27,000 10 C06(4)(1)273K1X5C(2) CK06BX273K CKR06BX273K(2)(3) 1232(3) 1272(3) 1312(3) 1352(3)
33,000 10 C06(4)(1)333K1X5C(2) CK06BX333K CKR06BX333K(2)(3) 1223(3) 1263(3) 1303(3) 1343(3)
33,000 20 C062K333M1X5CA CK06BX333M
39,000 10 C06(4)(1)393K1X5C(2) CK06BX393K CKR06BX393K(2)(3) 1224(3) 1264(3) 1304(3) 1344(3)
47,000 10 C06(4)(1)473K1X5C(2) CK06BX473K CKR06BX473K(2)(3) 1225(3) 1265(3) 1305(3) 1345(3)
47,000 20 C062K473M1X5CA CK06BX473M
56,000 10 C06(4)(1)563K1X5C(2) CK06BX563K CKR06BX563K(2)(3) 1226(3) 1266(3) 1306(3) 1346(3)
68,000 10 C06(4)(1)683K1X5C(2) CK06BX683K CKR06BX683K(2)(3) 1227(3) 1267(3) 1307(3) 1347(3)
68,000 20 C062K683M1X5CA CK06BX683M
82,000 10 C06(4)(1)823K1X5C(2) CK06BX823K CKR06BX823K(2)(3) 1229(3) 1269(3) 1309(3) 1349(3)
100,000 10 C06(4)(1)104K1X5C(2) CK06BX104K CKR06BX104K(2)(3) 1230(3) 1270(3) 1310(3) 1350(3)
100,000 20 C062K104M1X5CA CK06BX104M
120,000 10 C06(4)(1)124K5X5C(2) CK06BX124K CKR06BX124K(2)(3) 1233(3) 1273(3) 1313(3) 1353(3)
150,000 10 C06(4)(1)154K5X5C(2) CK06BX154K CKR06BX154K(2)(3) 1234(3) 1274(3) 1314(3) 1354(3)
150,000 20 C062K154M5X5CA CK06BX154M
180,000 10 C06(4)(1)184K5X5C(2) CK06BX184K CKR06BX184K(2)(3) 1235(3) 1275(3) 1315(3) 1355(3)
220,000 10 C06(4)(1)224K5X5C(2) CK06BX224K CKR06BX224K(2)(3) 1236(3) 1276(3) 1316(3) 1356(3)
220,000 20 C062K224M5X5CA CK06BX224M
270,000 10 C06(4)(1)274K5X5C(2) CK06BX274K CKR06BX274K(2)(3) 1237(3) 12773) 1317(3) 1357(3)
330,000 10 C06(4)(1)334K5X5C(2) CK06BX334K CKR06BX334K(2)(3) 1238(3) 1278(3) 1318(3) 1358(3)
330,000 20 C062K334M5X5CA CK06BX334M
390,000 10 C06(4)(1)394K5X5C(2) CK06BX394K CKR06BX394K(2)(3) 1239(3) 1279(3) 1319(3) 1359(3)
470,000 10 C06(4)(1)474K5X5C(2) CK06BX474K CKR06BX474K(2)(3) 1240(3) 1280(3) 1320(3) 1360(3)
470,000 20 C062K474M5X5CA CK06BX474M
560,000 10 C06(4)(1)564K5X5C(2) CK06BX564K CKR06BX564K(2)(3) 1404(3) 1408(3) 1412(3) 1416(3)
680,000 10 C06(4)(1)684K5X5C(2) CK06BX684K CKR06BX684K(2)(3) 1405(3) 1409(3) 1413(3) 1417(3)
680,000 20 C062K684M5X5CA CK06BX684M
820,000 10 C06(4)(1)824K5X5C(2) CK06BX824K CKR06BX824K(2)(3) 1406(3) 1410(3) 1414(3) 1418(3)
1,000,000 10 C06(4)(1)105K5X5C(2) CK06BX105K CKR06BX105K(2)(3) 1407(3) 1411(3) 1415(3) 1419(3)
1,000,000 20 C062K105M5X5CA CK06BX105M
50 VOLT – C062/C066 SIZE (MILITARY-CK06 or CKR06)
100 VOLT – C062/C066 SIZE (MILITARY-CK06 or CKR06)
MIL-PRF-39014/02 For Failure
Rate Levels (2)
200 VOLT – C062/C066 SIZE (MILITARY-CK06 or CKR06)
CAP.
pF
TOL.
%
KEMET
PART NUMBER
MIL-C-11015/19
MIL-PRF-39014/02
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630046
CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Axial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Axial Leaded Ceramic Capacitors for automatic insertion
orlead forming machines per EIA specification RS-296. KEMET’s
internal specification four-digit suffix, 7200, is placed at the end of
the part number to designate tape and reel packaging, ie:
C410C104Z5U5CA7200.
Paper (50 lb.) test minimum is inserted between the layers of
capacitors wound on reels for component pitch ≤0.400”.
Capacitor lead length may extend only a maximum of .0625”
(1.59mm) beyond the tapes’ edges. Capacitors are centered in a
row between the two tapes and will deviate only ± 0.031
(0.79mm) from the row center. A minimum of 36” (91.5 cm) leader
tape is provided at each end of the reel capacitors. Universal
splicing clips are used to connect the tape. Standard reel
quantities are shown on page 48.
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 47
Tape and Reel Packaging
CERAMIC LEADED
PACKAGING INFORMATION
©KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-630048
CERAMIC LEADED
PACKAGING INFORMATION
KEMET
Series
Military
Style
Military
Specification
Standard (1)
Bulk
Quantity
Ammo Pack
Quantity
Maximum
Maximum
Reel
Quantity
Reel
Size
C114C-K-G CK12, CC75 MIL-C-11015/ 200/Box 5000 12"
C124C-K-G CK13, CC76 MIL-PRF-20 200/Box 5000 12"
C192C-K-G CK14, CC77 100/Box 3000 12"
C202C-K CK15 25/Box 500 12"
C222C-K CK16 10/Tray 300 12"
C052C-K-G CK05, CC05 100/Bag 2000 2000 12"
C062C-K-G CK06, CC06 100/Bag 1500 1500 12"
C114G CCR75 MIL-PRF-20 200/Box 5000 12"
C124G CCR76 200/Box 5000 12"
C192G CCR77 100/Box 3000 12"
C202G CC78-CCR78 25/Box 500 12"
C222G CC79-CCR79 10/Tray 300 12"
C052/56G CCR05 100/Bag 1700 12"
C062/66G CCR06 100/Bag 1500 12"
C512G CC07-CCR07 Footnote (2) N/A N/A
C522G CC08-CCR08 Footnote (2) N/A N/A
C114T CKR11 MIL-PRF-39014 200/Box 5000 12"
C124T CKR12 200/Box 5000 12"
C192T CKR14 100/Box 3000 12"
C202T CKR15 25/Box 500 12"
C222T CKR16 10/Tray 300 12"
C052/56T CKR05 100/Bag 1700 12"
C062/66T CKR06 100/Bag 1500 12"
C31X 500/Bag 2500 2500 12"
C32X 500/Bag 2500 2500 12"
C33X 250/Bag 1500 1500 12"
C340 100/Bag 1000 1000 12"
C350 50/Bag N/A 500 12"
C410 300/Box 4000 5000 12"
C412 200/Box 4000 5000 12"
C420 300/Box 4000 5000 12"
C430 200/Box 2000 2500 12"
C440 200/Box 2000 2500 12"
C512 N/A N/A Footnote (2) N/A N/A
C522 N/A N/A Footnote (2) N/A N/A
C617 250/Bag 1000 12"
C622/C623 100/Bag 500 12"
C627/C628 100/Bag 500 12"
C630/C631 100/Bag 500 12"
C637/C638 50/Bag 500 12"
C640/C641 50/Bag 500 12"
C642/C643 50/Bag 500 12"
C647/C648 50/Bag 500 12"
C657/C658 50/Bag 500 12"
C667/C668 50/Bag 500 12"
CERAMIC PACKAGING
NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.
(2) Quantity varies. For further details, please consult the factory.