LF198,LF198A,LF298,LF398,LF398A
LF198/LF298/LF398, LF198A/LF398A Monolithic Sample-and-Hold Circuits
Literature Number: SNOSBI3A
LF198/LF298/LF398, LF198A/LF398A
Monolithic Sample-and-Hold Circuits
General Description
The LF198/LF298/LF398 are monolithic sample-and-hold
circuits which utilize BI-FET technology to obtain ultra-high
dc accuracy with fast acquisition of signal and low droop
rate. Operating as a unity gain follower, dc gain accuracy is
0.002% typical and acquisition time is as low as 6 µs to
0.01%. A bipolar input stage is used to achieve low offset
voltage and wide bandwidth. Input offset adjust is accom-
plished with a single pin, and does not degrade input offset
drift. The wide bandwidth allows the LF198 to be included in-
side the feedback loop of 1 MHz op amps without having sta-
bility problems. Input impedance of 10
10
Ωallows high
source impedances to be used without degrading accuracy.
P-channel junction FET’s are combined with bipolar devices
in the output amplifier to give droop rates as low as 5 mV/min
witha1µFhold capacitor. The JFET’s have much lower
noise than MOS devices used in previous designs and do
not exhibit high temperature instabilities. The overall design
guarantees no feed-through from input to output in the hold
mode, even for input signals equal to the supply voltages.
Features
nOperates from ±5V to ±18V supplies
nLess than 10 µs acquisition time
nTTL, PMOS, CMOS compatible logic input
n0.5 mV typical hold step at C
h
= 0.01 µF
nLow input offset
n0.002% gain accuracy
nLow output noise in hold mode
nInput characteristics do not change during hold mode
nHigh supply rejection ratio in sample or hold
nWide bandwidth
nSpace qualified, JM38510
Logic inputs on the LF198 are fully differential with low input
current, allowing direct connection to TTL, PMOS, and
CMOS. Differential threshold is 1.4V. The LF198 will operate
from ±5V to ±18V supplies.
An “A” version is available with tightened electrical
specifications.
Typical Connection and Performance Curve
Functional Diagram
DS005692-32
Acquisition Time
DS005692-16
DS005692-1
July 2000
LF198/LF298/LF398, LF198A/LF398A Monolithic Sample-and-Hold Circuits
© 2000 National Semiconductor Corporation DS005692 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage ±18V
Power Dissipation (Package
Limitation) (Note 2) 500 mW
Operating Ambient Temperature Range
LF198/LF198A −55˚C to +125˚C
LF298 −25˚C to +85˚C
LF398/LF398A 0˚C to +70˚C
Storage Temperature Range −65˚C to +150˚C
Input Voltage Equal to Supply Voltage
Logic To Logic Reference
Differential Voltage (Note 3) +7V, −30V
Output Short Circuit Duration Indefinite
Hold Capacitor Short
Circuit Duration 10 sec
Lead Temperature (Note 4)
H package (Soldering, 10 sec.) 260˚C
N package (Soldering, 10 sec.) 260˚C
M package:
Vapor Phase (60 sec.) 215˚C
Infrared (15 sec.) 220˚C
Thermal Resistance (θ
JA
) (typicals)
H package 215˚C/W (Board mount in still air)
85˚C/W (Board mount in
400LF/min air flow)
N package 115˚C/W
M package 106˚C/W
θ
JC
(H package, typical) 20˚C/W
Electrical Characteristics
The following specifcations apply for −V
S
+ 3.5V ≤V
IN
≤+V
S
− 3.5V, +V
S
= +15V, −V
S
= −15V, T
A
=T
j
= 25˚C, C
h
= 0.01 µF,
R
L
=10kΩ, LOGIC REFERENCE = 0V, LOGIC HIGH = 2.5V, LOGIC LOW = 0V unless otherwise specified.
Parameter Conditions LF198/LF298 LF398 Units
Min Typ Max Min Typ Max
Input Offset Voltage, (Note 5) T
j
= 25˚C 1 3 2 7 mV
Full Temperature Range 5 10 mV
Input Bias Current, (Note 5) T
j
= 25˚C 5 25 10 50 nA
Full Temperature Range 75 100 nA
Input Impedance T
j
= 25˚C 10
10
10
10
Ω
Gain Error T
j
= 25˚C, R
L
= 10k 0.002 0.005 0.004 0.01 %
Full Temperature Range 0.02 0.02 %
Feedthrough Attenuation Ratio T
j
= 25˚C, C
h
= 0.01 µF 86 96 80 90 dB
at 1 kHz
Output Impedance T
j
= 25˚C, “HOLD” mode 0.5 2 0.5 4 Ω
Full Temperature Range 4 6 Ω
“HOLD” Step, (Note 6) T
j
= 25˚C, C
h
= 0.01 µF, V
OUT
= 0 0.5 2.0 1.0 2.5 mV
Supply Current, (Note 5) T
j
≥25˚C 4.5 5.5 4.5 6.5 mA
Logic and Logic Reference Input T
j
= 25˚C 2 10 2 10 µA
Current
Leakage Current into Hold T
j
= 25˚C, (Note 7) 30 100 30 200 pA
Capacitor (Note 5) Hold Mode
Acquisition Time to 0.1% ∆V
OUT
= 10V, C
h
= 1000 pF 4 4 µs
C
h
= 0.01 µF 20 20 µs
Hold Capacitor Charging Current V
IN
−V
OUT
=2V 5 5 mA
Supply Voltage Rejection Ratio V
OUT
= 0 80 110 80 110 dB
Differential Logic Threshold T
j
= 25˚C 0.8 1.4 2.4 0.8 1.4 2.4 V
Input Offset Voltage, (Note 5) T
j
= 25˚C 1 1 2 2 mV
Full Temperature Range 2 3 mV
Input Bias Current, (Note 5) T
j
= 25˚C 5 25 10 25 nA
Full Temperature Range 75 50 nA
LF198/LF298/LF398, LF198A/LF398A
www.national.com 2
Electrical Characteristics
The following specifcations apply for −V
S
+ 3.5V ≤V
IN
≤+V
S
− 3.5V, +V
S
= +15V, −V
S
= −15V, T
A
=T
j
= 25˚C, C
h
= 0.01 µF,
R
L
=10kΩ, LOGIC REFERENCE = 0V, LOGIC HIGH = 2.5V, LOGIC LOW = 0V unless otherwise specified.
Parameter Conditions LF198A LF398A Units
Min Typ Max Min Typ Max
Input Impedance T
j
= 25˚C 10
10
10
10
Ω
Gain Error T
j
= 25˚C, R
L
= 10k 0.002 0.005 0.004 0.005 %
Full Temperature Range 0.01 0.01 %
Feedthrough Attenuation Ratio T
j
= 25˚C, C
h
= 0.01 µF 86 96 86 90 dB
at 1 kHz
Output Impedance T
j
= 25˚C, “HOLD” mode 0.5 1 0.5 1 Ω
Full Temperature Range 4 6 Ω
“HOLD” Step, (Note 6) T
j
= 25˚C, C
h
= 0.01µF, V
OUT
= 0 0.5 1 1.0 1 mV
Supply Current, (Note 5) T
j
≥25˚C 4.5 5.5 4.5 6.5 mA
Logic and Logic Reference Input T
j
= 25˚C 2 10 2 10 µA
Current
Leakage Current into Hold T
j
= 25˚C, (Note 7) 30 100 30 100 pA
Capacitor (Note 5) Hold Mode
Acquisition Time to 0.1% ∆V
OUT
= 10V, C
h
= 1000 pF 4 6 4 6 µs
C
h
= 0.01 µF 20 25 20 25 µs
Hold Capacitor Charging Current V
IN
−V
OUT
=2V 5 5 mA
Supply Voltage Rejection Ratio V
OUT
= 0 90 110 90 110 dB
Differential Logic Threshold T
j
= 25˚C 0.8 1.4 2.4 0.8 1.4 2.4 V
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX,θJA, and the ambient temperature, TA. The maximum
allowable power dissipation at any temperature is PD=(T
JMAX −T
A
)/θJA, or the number given in the Absolute Maximum Ratings, whichever is lower. The maximum
junction temperature, TJMAX, for the LF198/LF198A is 150˚C; for the LF298, 115˚C; and for the LF398/LF398A, 100˚C.
Note 3: Although the differential voltage may not exceed the limits given, the common-mode voltage on the logic pins may be equal to the supply voltages without
causing damage to the circuit. For proper logic operation, however, one of the logic pins must always be at least 2V below the positive supply and 3V above the nega-
tive supply.
Note 4: See AN-450 “Surface Mounting Methods and their effects on Product Reliability” for other methods of soldering surface mount devices.
Note 5: These parameters guaranteed over a supply voltage range of ±5to±
18V, and an input range of −VS+ 3.5V ≤VIN ≤+VS− 3.5V.
Note 6: Hold step is sensitive to stray capacitive coupling between input logic signals and the hold capacitor. 1 pF, for instance, will create an additional 0.5 mV step
with a 5V logic swing and a 0.01µF hold capacitor. Magnitude of the hold step is inversely proportional to hold capacitor value.
Note 7: Leakage current is measured at a junction temperature of 25˚C. The effects of junction temperature rise due to power dissipation or elevated ambient can
be calculated by doubling the 25˚C value for each 11˚C increase in chip temperature. Leakage is guaranteed over full input signal range.
Note 8: A military RETS electrical test specification is available on request. The LF198 may also be procured to Standard Military Drawing #5962-8760801GA or to
MIL-STD-38510 part ID JM38510/12501SGA.
Typical Performance Characteristics
Note 9: See Definition of Terms
Aperture Time
(Note 9)
DS005692-17
Dielectric Absorption
Error in Hold Capacitor
DS005692-18
Dynamic Sampling Error
DS005692-19
LF198/LF298/LF398, LF198A/LF398A
www.national.com3
Typical Performance Characteristics (Continued)
Note 10: See Definition
Output Droop Rate
DS005692-20
Hold Step
DS005692-21
“Hold” Settling Time
(Note 10)
DS005692-22
Leakage Current into Hold
Capacitor
DS005692-23
Phase and Gain (Input to
Output, Small Signal)
DS005692-24
Gain Error
DS005692-25
Power Supply Rejection
DS005692-26
Output Short Circuit Current
DS005692-27
Output Noise
DS005692-28
LF198/LF298/LF398, LF198A/LF398A
www.national.com 4
Typical Performance Characteristics (Continued)
Logic Input Configurations
Input Bias Current
DS005692-29
Feedthrough Rejection Ratio
(Hold Mode)
DS005692-30
Hold Step vs Input Voltage
DS005692-31
Output Transient at Start
of Sample Mode
DS005692-12
Output Transient at Start
of Hold Mode
DS005692-13
TTL & CMOS
3V ≤V
LOGIC
(Hi State) ≤7V
DS005692-33
Threshold = 1.4V
DS005692-34
Threshold = 1.4V
*Select for 2.8V at pin 8
LF198/LF298/LF398, LF198A/LF398A
www.national.com5
Logic Input Configurations (Continued)
Application Hints
Hold Capacitor
Hold step, acquisition time, and droop rate are the major
trade-offs in the selection of a hold capacitor value. Size and
cost may also become important for larger values. Use of the
curves included with this data sheet should be helpful in se-
lecting a reasonable value of capacitance. Keep in mind that
for fast repetition rates or tracking fast signals, the capacitor
drive currents may cause a significant temperature rise in
the LF198.
A significant source of error in an accurate sample and hold
circuit is dielectric absorption in the hold capacitor. A mylar
cap, for instance, may “sag back” up to 0.2% after a quick
change in voltage. A long sample time is required before the
circuit can be put back into the hold mode with this type of
capacitor. Dielectrics with very low hysteresis are polysty-
rene, polypropylene, and Teflon. Other types such as mica
and polycarbonate are not nearly as good. The advantage of
polypropylene over polystyrene is that it extends the maxi-
mum ambient temperature from 85˚C to 100˚C. Most ce-
ramic capacitors are unusable with >1% hysteresis. Ce-
ramic “NPO” or “COG” capacitors are now available for
125˚C operation and also have low dielectric absorption. For
more exact data, see the curve
Dielectric Absorption Error.
The hysteresis numbers on the curve are final values, taken
after full relaxation. The hysteresis error can be significantly
reduced if the output of the LF198 is digitized quickly after
the hold mode is initiated. The hysteresis relaxation time
constant in polypropylene, for instance, is 10—50 ms. If
A-to-D conversion can be made within 1 ms, hysteresis error
will be reduced by a factor of ten.
DC and AC Zeroing
DC zeroing is accomplished by connecting the offset adjust
pin to the wiper ofa1kΩpotentiometer which has one end
tied to V
+
and the other end tied through a resistor to ground.
The resistor should be selected to give ≈0.6 mA through the
1k potentiometer.
AC zeroing (hold step zeroing) can be obtained by adding an
inverter with the adjustment pot tied input to output. A 10 pF
capacitor from the wiper to the hold capacitor will give ±4mV
hold step adjustment with a 0.01 µF hold capacitor and 5V
logic supply. For larger logic swings, a smaller capacitor
(<10 pF) may be used.
Logic Rise Time
For proper operation, logic signals into the LF198 must have
a minimum dV/dt of 1.0 V/µs. Slower signals will cause ex-
cessive hold step. If a R/C network is used in front of the
CMOS
7V ≤V
LOGIC
(Hi State) ≤15V
DS005692-35
Threshold = 0.6 (V+) + 1.4V DS005692-36
Threshold = 0.6 (V+) − 1.4V
Op Amp Drive
DS005692-37
Threshold ≈+4V DS005692-38
Threshold = −4V
LF198/LF298/LF398, LF198A/LF398A
www.national.com 6
Application Hints (Continued)
logic input for signal delay, calculate the slope of the wave-
form at the threshold point to ensure that it is at least
1.0 V/µs.
Sampling Dynamic Signals
Sample error to moving input signals probably causes more
confusion among sample-and-hold users than any other pa-
rameter. The primary reason for this is that many users make
the assumption that the sample and hold amplifier is truly
locked on to the input signal while in the sample mode. In ac-
tuality, there are finite phase delays through the circuit creat-
ing an input-output differential for fast moving signals. In ad-
dition, although the output may have settled, the hold
capacitor has an additional lag due to the 300Ωseries resis-
tor on the chip. This means that at the moment the “hold”
command arrives, the hold capacitor voltage may be some-
what different than the actual analog input. The effect of
these delays is opposite to the effect created by delays in the
logic which switches the circuit from sample to hold. For ex-
ample, consider an analog input of 20 Vp-p at 10 kHz. Maxi-
mum dV/dt is 0.6 V/µs. With no analog phase delay and 100
ns logic delay, one could expect up to (0.1 µs) (0.6V/µs)
= 60 mVerror if the “hold” signal arrived near maximum dV/dt
of the input. A positive-going input would give a +60 mV er-
ror. Now assume a 1 MHz (3 dB) bandwidth for the overall
analog loop. This generates a phase delay of 160 ns. If the
hold capacitor sees this exact delay, then error due to analog
delay will be (0.16 µs) (0.6 V/µs) = −96 mV. Total output error
is +60 mV (digital) −96 mV (analog) for a total of −36 mV. To
add to the confusion, analog delay is proportioned to hold
capacitor value while digital delay remains constant.A family
of curves (dynamic sampling error) is included to help esti-
mate errors.
A curve labeled
Aperture Time
has been included for sam-
pling conditions where the input is steady during the sam-
pling period, but may experience a sudden change nearly
coincident with the “hold” command. This curve is based on
a 1 mV error fed into the output.
A second curve,
Hold Settling Time
indicates the time re-
quired for the output to settle to 1 mV after the “hold” com-
mand.
Digital Feedthrough
Fast rise time logic signals can cause hold errors by feeding
externally into the analog input at the same time the amplifier
is put into the hold mode. To minimize this problem, board
layout should keep logic lines as far as possible from the
analog input and the C
h
pin. Grounded guarding traces may
also be used around the input line, especially if it is driven
from a high impedance source. Reducing high amplitude
logic signals to 2.5V will also help.
Guarding Technique
DS005692-5
Use 10-pin layout. Guard around C
h
is tied to output.
LF198/LF298/LF398, LF198A/LF398A
www.national.com7
Typical Applications
X1000 Sample & Hold
DS005692-39
*For lower gains, the LM108 must be frequency compensated
Sample and Difference Circuit
(Output Follows Input in
Hold
Mode)
DS005692-40
VOUT =V
B+∆V
IN(HOLD MODE)
Ramp Generator with Variable Reset Level
DS005692-42
Integrator with Programmable Reset Level
DS005692-43
LF198/LF298/LF398, LF198A/LF398A
www.national.com 8
Typical Applications (Continued)
Output Holds at Average of Sampled Input
DS005692-46
Increased Slew Current
DS005692-47
Reset Stabilized Amplifier (Gain of 1000)
DS005692-49
Fast Acquisition, Low Droop Sample & Hold
DS005692-50
LF198/LF298/LF398, LF198A/LF398A
www.national.com9
Typical Applications (Continued)
Synchronous Correlator for Recovering
Signals Below Noise Level
DS005692-52
2–Channel Switch
DS005692-53
AB
Gain 1 ±0.02% 1 ±0.2%
Z
IN
10
10
Ω47 kΩ
BW .1 MHz .400 kHz
Crosstalk −90 dB −90 dB
@1 kHz
Offset ≤6mV ≤75 mV
DC & AC Zeroing
DS005692-59
Staircase Generator
DS005692-55
*Select for step height
50k →≅1V Step
LF198/LF298/LF398, LF198A/LF398A
www.national.com 10
Typical Applications (Continued)
Definition of Terms
Hold Step: The voltage step at the output of the sample and
hold when switching from sample mode to hold mode with a
steady (dc) analog input voltage. Logic swing is 5V.
Acquisition Time: The time required to acquire a new ana-
log input voltage with an output step of 10V. Note that acqui-
sition time is not just the time required for the output to settle,
but also includes the time required for all internal nodes to
settle so that the output assumes the proper value when
switched to the hold mode.
Gain Error: The ratio of output voltage swing to input volt-
age swing in the sample mode expressed as a per cent dif-
ference.
Hold Settling Time: The time required for the output to
settle within 1 mV of final value after the “hold” logic com-
mand.
Dynamic Sampling Error: The error introduced into the
held output due to a changing analog input at the time the
hold command is given. Error is expressed in mV with a
given hold capacitor value and input slew rate. Note that this
error term occurs even for long sample times.
Aperture Time: The delay required between “Hold” com-
mand and an input analog transition, so that the transition
does not affect the held output.
Connection Diagrams
Differential Hold
DS005692-57
Capacitor Hysteresis Compensation
DS005692-56
**Adjust for amplitude
Dual-In-Line Package
DS005692-11
Order Number LF398N
or LF398AN
See NS Package Number N08E
Small-Outline Package
DS005692-15
Order Number LF298M or LF398M
See NS Package Number M14A
Metal Can Package
DS005692-14
Order Number LF198H,
LF198H/883, LF298H,
LF398H, LF198AH or LF398AH
See NS Package Number H08C
(Note 8)
LF198/LF298/LF398, LF198A/LF398A
www.national.com11
Physical Dimensions inches (millimeters) unless otherwise noted
Metal Can Package (H)
Order Number LF198H, LF298H, LF398H, LF198AH or LF398AH
NS Package Number H08C
Molded Small-Outline Package (M)
Order Number LF298M or LF398M
NS Package Number M14A
LF198/LF298/LF398, LF198A/LF398A
www.national.com 12
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
Molded Dual-In-Line Package (N)
Order Number LF398N or LF398AN
NS Package Number N08E
LF198/LF298/LF398, LF198A/LF398A Monolithic Sample-and-Hold Circuits
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
