214
ALUMINUM ELECTROLYTIC CAPACITORS
CAT.8100H
φD
P
φd
8
3.5
0.6
10
5.0
0.6
12.5
5.0
0.6
16
7.5
0.8
18
7.5
0.8
L+ MAX. 15 MIN 4MIN
d
(mm)
Configuration
φDPb-free leadwire
Pb-free PET sleeve
8 10
12.5 to 18
PD
HD
Sleeve (P.E.T.)
Pressure relief vent
φD+ 0.5MAX.
(L < 20) 1.5
(L 20) 2.0
P±0.5
U
1
P
2
A
3
1
4
A
5
4
6
7
7
1
8
M
9
P
10
D
11 12
Size code
Configuration
Series name
Type
Capacitance tolerance ( ±20%)
Rated capacitance (470µF)
Rated voltage (10V)
UPA Miniature Sized, Low lmpedance,
High Reliability For
Switching Power Supplies
Radial Lead Type
Lower impedance than UPW.
Smaller case size and high ripple current.
Compliant to the RoHS directive (2011/65/EU).
Dimension table in next page.
Specifications
UPA
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 4 for the minimum order quantity.
Low
Impedance
Performance Characteristics
ltem
0.22 0.19 0.16 0.14 0.12
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Marking
–55 to +105˚C
6.3 to 35V
180 to 10000µF
± 20% at 120Hz, 20˚C
After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV or 4 (µA), whichever is greater.
Rated voltage (V)
Rated voltage (V)
tan
δ
(MAX.)
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
6.3 10 16 25 35
3 3 3 3 3
6.3 10 16 25 35
Printed with white color letter on dark brown sleeve.
120Hz 20˚C
120Hz
Impedance ratio ZT / Z20 (MAX.) Z–55˚C / Z+20˚C
Shelf Life After storing the capacitors under no load at 105˚C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Type numbering system (Example : 10V 470µF)
UPW
50Hz 120Hz 300Hz 1kHz 10kHz or more
0.75
0.80
0.90
0.85
0.90
0.95
Cap. (µF) Frequency
1.00
1.00
1.00
Frequency coefficient of rated ripple current
180 to 330
390 to 1000
1200 to 10000
0.65
0.75
0.85
0.55
0.70
0.80
• Please refer to page 20 about the end seal configuration.
Capacitance change
Leakage current
The specifications listed at right shall be met when the
capacitors are restored to 20˚C after D.C. bias plus
rated ripple current is applied for 5000 hours (3000
hours for φD=8, 4000 hours for φD=10) at 105˚C, the
peak voltage shall not exceed the rated voltage.
tan δ
Within ± 20% of the initial capacitance value (6.3V, 10V : ± 30%)
Less than or equal to the initial specified value
200% or less than the initial specified value (6.3V, 10V : 300%)