1
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-sourced 2x5 Pin Package
• Complies with IEEE 802.3 Gigabit Ethernet
• 1270 nm to1610 nm Wavelength, CWDM DFB Laser
• Single +3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output (C-1XX-1250C-FDFB-SLCX)
• LVPECL Signal Detection Output (C-1XX-1250-FDFB-SLCX)
• Temperature Range: 0 to 70 ºC
• Class 1 Laser International Safety Standard IEC 825
compliant
• Solderability to MIL-STD-883, Method 2003
• Pin Coating is Sn/Pb with minimum 2% Pb content
• Flammability to UL94V0
• Humidity RH 5-85% (5-90% short term) to IEC 68-2-3
• Complies with Bellcore GR-468-CORE
• Uncooled laser diode with MQW structure
• 1.25 Gbps Ethernet Links application
• 1.06 Gbps Fiber Channel application
Parameter Symbol Min. Max. Unit Note
Power Supply Voltage Vcc 0 3.6 V
Output Current Iout 0 30 mA
Soldering Temperature - - 260 ºC 10 seconds on leads only
Operating Temperature Topr 0 70 ºC
Storage Temperature Tstg -40 85 ºC
Absolute Maximum Rating
Parameter Symbol Min. Typ. Max. Unit
Power Supply Voltage Vcc 3.1 3.3 3.5 V
Operating Temperature (Case) Topr 0 - 70 ºC
Data rate - 1250 - Mbps
Recommended Operating Condition
2
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
Parameter Symbol Min Typical Max Unit Notes
Electrical
Power Supply Current ICC - - 180 mA Maximum current is specied at Vcc=
Maximum @ maximum temperature
Transmit Enable Voltage VEN 0 - 0.8 V
Transmit Disable Voltage VD 2.0 - Vcc V
Data Input Current-Low IIL -200 - - µA
Data Input Current-High IIH - - 200 µA
Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V These inputs are compatible with 10K,
10KH and 100K ECL and PECL inputs
Data Input Voltage-High VIH-VCC -1.1 - -0.74 V
Transmitter Specications
Parameter Symbol Min Typical Max Unit Notes
Optical
Sensitivity - - - -22 dBm Measured with 27-1 PRBS, BER = 10 -12
Maximum Input Power Pin -3 - - dBm
Signal Detect-Asserted Pa - - -22 dBm Measured on transition: low to high
Signal Detect-Deasserted Pd -38 - - dBm Measured on transition: high to low
Signal Detect-Hysteresis 1.0 - - dB
Wavelength of Operation 1100 - 1620 nm
Receiver Specications
Parameter Symbol Min Typical Max Unit Notes
Optical
Optical Transmit Power Po-5 - 0 dBm C-1XX-1250(C)-FDFB-SLC2
Optical Transmit Power Po-3 - +2 dBm C-1XX-1250(C)-FDFB-SLC3
Optical Transmit Power Po0 - +5 dBm C-1XX-1250(C)-FDFB-SLC4
Output center Wavelength λ λp-5.5 λpλp+7.5 nm λp=1XX0 nm,
C-1XX-1250(C)-FDFB-SLCX
Output Spectrum Width λ- - 1 nm -20 dB width
Side Mode Suppression Ratio Sr 30 35 - dBm CW, Po=5mW
Extinction Ratio ER 9 - - dB
Output Eye Compliant with IEEE 802.3
Optical Rise Time tr - - 0.26 ns 20% to 80% Values
Optical Fall Time tf - - 0.26 ns 20% to 80% Values
Relative Intensity Noise RIN - - -120 dB/Hz
Total Jitter TJ - - 0.27 ns Measured with 27-1 PRBS
Transmitter Specications
3
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
Legal Notice
Connection Diagram
PIN Symbol Notes
1RxGND Directly connect this pin to the receiver ground plane
2 TxVcc +3.3 V dc power for the receiver section
3 SD Active high on this indicates a received optical signal(LVPECL/LVTTL)
4 RD- Receiver Data Out Bar (LVPECL)
5 RD+ Receiver Dat Out (LVPECL)
6 TxVcc +3.3 V dc power for the transmitter section
7 TxGND Directly connect this pin to the transmitter ground plane
8 TxDIS Transmitter disable (LVTTL)
9 TD+ Transmitter Data In (LVPECL)
10 TD- Transmitter Data In Bar (LVPECL)
Attaching Posts The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
Parameter Symbol Min Typical Max Unit Note
Electrical
Power Supply Current ICC - - 120 mA The current excludes the output load current
Data Output Voltage-Low VOL -Vcc -2 - -1.58 V These outputs are compatible with 10K,
10KH and 100K ECL and LVPECL outputs
Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V
Signal Detect Output Voltage-Low VSDL-Vcc -2 - -1.58 V C-1XX-1250-FDFB-SLCX
Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V
Signal Detect Output Voltage-Low VSDL-Vcc - - 0.5 V C-1XX-1250C-FDFB-SLCX
Signal Detect Output Voltage-High VSDH- Vcc 2.0 - - V
Receiver Specications
4
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
Tx
Rx
TERMINATE AT
TRANSCEIVER INPUTS Z=50!
Z=50!
100!
TD-
TD
130!130!
Vcc(+3.3V)
100!
RD+
RD-
SD
Z=50!
Z=50!
Z=50!
130!130!
Vcc(+3.3V)
Vcc(+3.3V)
LVPECL
LVPECL
10"F
C3C2
1"H
67810 9
1 2 3 4 5
1"H
C1
TERMINATE AT
DEVICE INPUTS
NOTE:C1=C2=C3=100nF
RxGND
RxVcc
SD
RD-
RD+ TxVcc
TxGND
TD+
TD-
TxDIS
Recommended Circuit Schematic
Printed Circuit Board Layout Consideration
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply ltering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
Tx
Rx
TERMINATE AT
TRANSCEIVER INPUTS Z=50
Z=50
100
TD-
TD+
130
82
Vcc(+3.3V)
100
RD+
RD-
SD
Z=50
Z=50
Z=50
130130
Vcc(+3.3V)
Vcc(+3.3V)
PHY DEVICE
LVPECL
LVPECL
10F
C3C2
1H
67810 9
1 2 3 4 5
1H
C1
TERMINATE AT
DEVICE INPUTS
NOTE:C1=C2=C3=100nF
RxGND
RxVcc
SD
RD-
RD+ TxVcc
TxGND
TD+
TD-
TxDIS
Vcc(+3.3V)
130
130
C-1XX-1250C-FDFB-SLCX
C-1XX-1250-FDFB-SLCX
5
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
O1.00!0.05
17.78
10.50
(0.413)
(0.039)±(0.002)
(0.700)
7.12
(0.070)
(0.020)
1.78
0.50
(0.280)
3.81
5.08
(0.150)
(0.200)
6.25
(0.246)
(0.520)
13.20
(1.921)
10.16
(0.400)
"5.08
(0.
594
)
"".36
(0.
447
)
6.97
3.95
(0.274)
(0.155)
"3.50
9.80
(0.531)
(0.386)
2."8
(0.086)
48.8+0
-0.2
+(.000)
-(0.008)
(0.535)
-(0.004)
+(
.000
)
+0
-0."
"3.6
-(0.004)
+(
.000
)
(0.386)
-0."
+0
9.8
(0.374)
9.50
Package Diagram
A ber-optic receiver employs a very high gain, wide bandwidth transimpedance amplier. This amplier detects and amplies
signals that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must
be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of
signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high
speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi lter
be used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs ush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
Units in mm(inch)
Printed Circuit Board Layout Consideration
6
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
Recommended Board Layout Hole Pattern
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
DIMENSION IN MILLIMETER (INCHES)
NOTES:
7
1.25 Gbps Single Mode SFF LC Transceiver
C-1XX-1250(C)-FDFB-SLCX
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS771-AUG2304
rev. A.0
LUMINENTOIC.COM
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specications only in accordance with the company’s standard one-year warranty; however, specications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-
ties, warranties of merchantability, tness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-
ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Warnings:
Legal Notes:
Ordering Information
C - 1XX- 1250(C) - FDFB - S LC TxPower
• 1XX = Wavelength 1XX0 nm
XX=27, 29, 31, 33, 35, 37, 39,
41, 43, 45, 47, 49, 51, 53, 55,
57, 59, 61
• Communication protocol
1250= LVPECL SD output
1250C= LVTTL SD output
• Connector options
• Tx Power range
2 = -5 to 0 dBm
3 = -3 to +2 dBm
4 = 0 to +5 dBm
• FDFB = +3.3V SFF Transceiver
• Single mode ber
Available Options:
C-1XX-1250-FDFB-SLC2
C-1XX-1250-FDFB-SLC3
C-1XX-1250-FDFB-SLC4
C-1XX-1250C-FDFB-SLC2
C-1XX-1250C-FDFB-SLC3
C-1XX-1250C-FDFB-SLC4
Part numbering Denition: