UG246: Si875x User's Guide The Si875x isolated MOSFET driver is ideal for driving power switches used in a wide variety of applications, offering longer service life and dramatically higher reliability compared to common SSRs. The Si875x isolated MOSFET driver utilizes Silicon Laboratories' proprietary silicon isolation technology supporting up to 2.5 kVRMS withstand voltage per UL1577 and VDE0884. This technology enables reduced variation with temperature and age, better part-to-part matching, and extremely high reliability. High integration, low propagation delay, small installed size, flexibility, and cost-effectiveness make the Si875x ideal for a wide range of isolated MOSFET gate drive applications. The Si875x evaluation board allows designers to evaluate Silicon Labs' Si875x family of MOSFET drivers. The boards come populated with either the Si8751 (digital input) or Si8752 (LED emulator input) version of the family. The board includes screw terminals for quick evaluation of the device's key parameters and also includes test points on each of the device's pins to accommodate direct connection to the designer's end system. For more ISOdriver information, visit the Silicon Labs website at www.silabs.com/isolation. silabs.com | Smart. Connected. Energy-friendly. KEY FEATURES OR KEY POINTS * Easy to use * Supports both dc or ac switching * Jumper selectable power reduction options * Jumper to evaluate Miller Clamp function * Digital input or diode emulation options * Si8751-KIT (digital input) * Si8752-KIT (diode emulation) Rev. 0.1 UG246: Si875x User's Guide Kit Contents 1. Kit Contents The Si875x Evaluation Kit contains the following items: * Si875x-based evaluation board shown in the figure below: Figure 1.1. Si8751 Evaluation Board Figure 1.2. Si8752 Evaluation Board silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 1 UG246: Si875x User's Guide EVB Test 2. EVB Test To run the test, follow the instructions in the following sections. 2.1 Required Equipment The following equipment is required to demonstrate the evaluation board: * 1 digital multimeter * 1 dc power supply: 0 - 5 V * 1 dc power supply: 0 - 15 V * 1 1k - 2k 0.25 W resistor * Assorted cables and leads as necessary to connect equipment to EVB * Si875x Evaluation Board (board under test) * Si827x Evaluation Board User's Guide (this document) 2.2 EVB Test To run the test, follow the instructions in the following sections. 2.2.1 DC Supply Configuration 1. Set the 5 V supply to output 5 VDC. 2. Turn OFF the supply and connect the positive lead to J1 pin1. 3. Connect the negative lead to J1 pin 2. 4. Set the 15 V supply to output 15 VDC. 5. Turn OFF the supply and connect the positive lead to J3 pin 1. 6. Connect the negative lead to J3 pin 2. 7. Connect the positive lead of the multimeter, and one end of the resistor, to J4 pin 1. 8. Connect the negative lead of the multimeter, and the other end of the resistor, to J4 pin 2. 9. Turn ON the dc power supplies. 10. Ensure that the current draw is less than 25 mA in any of the supplies. If it is larger, this indicates that either the board or Si875x has been damaged or the supply is connected backwards. 2.2.2 Test the Si875x DC Switch 1. Place a shunt between pins 2 and 3 of J2 (Si8751) or J5 (Si8752) and JP6. 2. The multimeter should measure 0 V. 3. Move the shunt from pins 2 and 3 to pins 1 and 2 on J2 (Si8751) or J5 (Si8752). 4. The multimeter should now measure 15 V. 5. Move the shunt back to pins 2 and 3. 6. Turn off the dc supplies. 2.2.3 Test the Si875x AC Switch 1. Move the 15 V supply positive lead to J6 pin1 and the negative lead to J6 pin 2. 2. Move the multimeter positive lead, and the resistor lead, to J7 pin 1 and the negative lead, and the resistor lead, to J7 pin 2. 3. Move the shunt from JP6 to JP8. 4. Turn on the dc supplies. Again, there should be no current draw greater than 25 mA. 5. The multimeter should measure 0 V. 6. Move the shunt on J2 (Si8751) or J5 (Si8752) from pins 2 and 3 to pins 1 and 2. 7. The multimeter should now measure 15 V. silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 2 UG246: Si875x User's Guide Schematics 3. Schematics Figure 3.1. Si8751-EVB Schematic Figure 3.2. Si8752-EVB Schematic silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 3 UG246: Si875x User's Guide Layout 4. Layout Figure 4.1. Primary Silkscreen silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 4 UG246: Si875x User's Guide Layout Figure 4.2. Primary Side silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 5 UG246: Si875x User's Guide Layout Figure 4.3. Secondary Side Figure 4.4. Secondary Silkscreen silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 6 UG246: Si875x User's Guide Bill of Materials 5. Bill of Materials Si8751-EVB Bill of Materials Table 5.1. Si8751-EVB Bill of Materials Qty Ref Value Type PCB_Footprint Manufacturer PN Manufacturer 1 C1 10uF X7R C1210 C1210X7R500-106M Venkel 2 C2 C3 0.1uF X7R C0805 C0805X7R101-104K Venkel 3 C4 C5 C6 200pF C0G C0805 C0805C0G500-201K Venkel 1 D1 5.6V Zener DO-214AA 1SMB5919BT3 On Semi 1 D2 RED SMT, ChipLED LED-HSMX-C170 HSMZ-C170 Avago Technologies 1 D3 ES1D Fast DO-214AC ES1D Diodes Inc. 5 J1 J3 J4 J6 J7 CONN TRBLK 2 TERM BLK MALE CONN-TB-1757242 1757242 PHOENIX CONTACT 1 J2 Header 1x3 Header CONN-1X3 TSW-103-07-G-S Samtec 9 JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP8 JP9 JUMPER Header CONN1X2 TSW-102-07-T-S Samtec 5 JP10 JP11 JP12 JP13 JP14 PLUG TERM BLK 1757019 Phoenix Contact 5 JS1 JS2 JS3 JS4 JS5 Jumper Shunt Shunt SHUNT SNT-100-BK-T Samtec 1 LB1 OPN: Si8751_EV B POLYIMIDE, WHITE PTL-14-477 LABEL-Si8751_EVB Silabs 4 MH1 MH2 MH3 MH4 4-40 HDW MH-125NP|MH-125 NSS-4-4-01 Richco Plastic Co 1 PCB1 N/A Si875x_EVB REV 1.0 SiLabs 3 Q2 Q4 Q5 FDD6N25 N-CHNL DPAK-G2SD FDD6N25 Fairchild 2 R1 R9 0 ThickFilm R0402|R0402L CR0402-16W-000 Venkel 1 R2 100 ThickFilm R0603|R0603L CR0603-10W-1000F Venkel 1 R4 49.9 ThickFilm R0805 CR0805-10W-49R9F Venkel 1 R5 10K ThickFilm R0805 CR0805-10W-1002F Venkel 1 R6 49.9K ThickFilm R0805 CR0805-10W-4992F Venkel 4 SO1 SO2 SO3 SO4 STANDOFF HDW 1902D Keystone Electronics Si875x_EV BARE PCB B REV 1.0 silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 7 UG246: Si875x User's Guide Bill of Materials Qty Ref Value Type PCB_Footprint Manufacturer PN Manufacturer 17 TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 TP10 TP11 TP13 TP14 TP15 TP16 TP17 TP18 WHITE Loop TESTPOINT 151-201-RC Kobiconn 1 U1 Si8751 Isolator SO8N6.0P1.27 Si8751 SiLabs Table 5.2. Si8751-EVB Not Installed Components Qty Reference Value Type PCB_Footprint ManufacturerPN Manufacturer 1 J5 Header 1x3 Header CONN-1X3 TSW-103-07-G-S Samtec 1 JS6 Jumper Shunt Shunt SHUNT SNT-100-BK-T Samtec 1 Q3 MMBT222 2LT1 NPN SOT23-BEC MMBT2222LT1 On Semi 3 Q6 Q7 Q8 IRG4BC10 UDPBF IGBT TO-220|TO220-UP IRG4BC10UDPBF IR 1 R3 330 ThickFilm R0805 CR0805-10W-3300F Venkel 1 R7 0 ThickFilm R0402|R0402L CR0402-16W-000 Venkel 1 R8 25.5K ThickFilm R0805 CR0805-10W-2552F Venkel 1 TP12 WHITE Loop TESTPOINT 151-201-RC Kobiconn silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 8 UG246: Si875x User's Guide Bill of Materials Si8752-EVB Bill of Materials Table 5.3. Si8752-EVB Bill of Materials Qty Reference Value Type PCB_Footprint ManufacturerPN Manufacturer 1 C1 10uF X7R C1210 C1210X7R500-106M Venkel 3 C4 C5 C6 200pF C0G C0805 C0805C0G500-201K Venkel 1 D1 5.6V Zener DO-214AA 1SMB5919BT3 On Semi 1 D2 RED SMT, ChipLED LED-HSMX-C170 HSMZ-C170 Avago Technologies 1 D3 ES1D Fast DO-214AC ES1D Diodes Inc. 5 J1 J3 J4 J6 J7 CONN TRBLK 2 TERM BLK MALE CONN-TB-1757242 1757242 PHOENIX CONTACT 1 J5 Header 1x3 Header CONN-1X3 TSW-103-07-G-S Samtec 5 JP10 JP11 JP12 JP13 JP14 PLUG TERM BLK 1757019 Phoenix Contact 5 JP5 JP6 JP7 JP8 JP9 JUMPER Header CONN1X2 TSW-102-07-T-S Samtec 3 JS4 JS5 JS6 Jumper Shunt Shunt SHUNT SNT-100-BK-T Samtec 1 LB1 OPN: Si8752_EV B POLYIMIDE, WHITE PTL-14-477 LABEL-Si8752_EVB Silabs 4 MH1 MH2 MH3 MH4 4-40 HDW MH-125NP|MH-125 NSS-4-4-01 Richco Plastic Co 1 PCB1 N/A Si875x_EVB REV 1.0 SiLabs 3 Q2 Q4 Q5 FDD6N25 N-CHNL DPAK-G2SD FDD6N25 Fairchild 1 Q3 MMBT222 2LT1 NPN SOT23-BEC MMBT2222LT1 On Semi 1 R2 100 ThickFilm R0603|R0603L CR0603-10W-1000F Venkel 1 R3 330 ThickFilm R0805 CR0805-10W-3300F Venkel 1 R7 0 ThickFilm R0402|R0402L CR0402-16W-000 Venkel 1 R8 25.5K ThickFilm R0805 CR0805-10W-2552F Venkel 4 SO1 SO2 SO3 SO4 STANDOFF HDW 1902D Keystone Electronics 17 TP1 TP2 TP3 TP4 TP5 TP7 TP8 TP9 TP10 TP11 TP12 TP13 TP14 TP15 TP16 TP17 TP18 WHITE Loop TESTPOINT 151-201-RC Kobiconn 1 U1 Si8752 Isolator SO8N6.0P1.27 Si8752 SiLabs Si875x_EV BARE PCB B REV 1.0 silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 9 UG246: Si875x User's Guide Bill of Materials Table 5.4. Si8752-EVB Not Installed Components Qty Reference Value Type PCB_Footprint ManufacturerPN Manufacturer 2 C2 C3 0.1uF X7R C0805 C0805X7R101-104K Venkel 1 J2 Header 1x3 Header CONN-1X3 TSW-103-07-G-S Samtec 4 JP1 JP2 JP3 JP4 JUMPER Header CONN1X2 TSW-102-07-T-S Samtec 3 JS1 JS2 JS3 Jumper Shunt Shunt SHUNT SNT-100-BK-T Samtec 3 Q6 Q7 Q8 IRG4BC10 UDPBF IGBT TO-220|TO220-UP IRG4BC10UDPBF IR 2 R1 R9 0 ThickFilm R0402|R0402L CR0402-16W-000 Venkel 1 R4 49.9 ThickFilm R0805 CR0805-10W-49R9F Venkel 1 R5 10K ThickFilm R0805 CR0805-10W-1002F Venkel 1 R6 49.9K ThickFilm R0805 CR0805-10W-4992F Venkel 1 TP6 WHITE Loop TESTPOINT 151-201-RC Kobiconn silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 10 Smart. Connected. Energy-Friendly. Products Quality www.silabs.com/products www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.(R) , Silicon Laboratories(R), Silicon Labs(R), SiLabs(R) and the Silicon Labs logo(R), Bluegiga(R), Bluegiga Logo(R), Clockbuilder(R), CMEMS(R), DSPLL(R), EFM(R), EFM32(R), EFR, Ember(R), Energy Micro, Energy Micro logo and combinations thereof, "the world's most energy friendly microcontrollers", Ember(R), EZLink(R), EZRadio(R), EZRadioPRO(R), Gecko(R), ISOmodem(R), Precision32(R), ProSLIC(R), Simplicity Studio(R), SiPHY(R), Telegesis, the Telegesis Logo(R), USBXpress(R) and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com