HI5735 (R) Data Sheet May 2003 12-Bit, 80 MSPS, High Speed Video D/A Converter Features * Throughput Rate . . . . . . . . . . . . . . . . . . . . . . . . 80 MSPS The HI5735 is a 12-bit, 80 MSPS, D/A converter which is implemented in the Intersil BiCMOS 10V (HBC-10) process. Operating from +5V and -5.2V, the converter provides -20.48mA of full scale output current and includes an input data register and bandgap voltage reference. Low glitch energy and excellent frequency domain performance are achieved using a segmented architecture. The digital inputs are TTL/CMOS compatible and translated internally to ECL. All internal logic is implemented in ECL to achieve high switching speed with low noise. The addition of laser trimming assures 12-bit linearity is maintained along the entire transfer curve. PART NUMBER HI5735KCB 0 to 70 PACKAGE 28 Lead SOIC 1 * Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .650mW * Integral Linearity Error . . . . . . . . . . . . . . . . . . . . 0.75 LSB * Low Glitch Energy . . . . . . . . . . . . . . . . . . . . . . . . .3.0pV-s * TTL/CMOS Compatible Inputs * Improved Hold Time. . . . . . . . . . . . . . . . . . . . . . . . 0.25ns * Excellent Spurious Free Dynamic Range Applications * Professional Video * Cable TV Headend Equipment Ordering Information TEMP. RANGE (oC) FN4133.4 PKG. NO. Pinout HI5735 (SOIC) TOP VIEW M28.3 D11 (MSB) 1 28 DGND D10 2 27 AGND D9 3 26 REF OUT D8 4 25 CTRL OUT D7 5 24 CTRL IN D6 6 23 RSET D5 7 22 AVEE D4 8 21 IOUT D3 9 20 IOUT D2 10 19 ARTN D1 11 18 DVEE D0 (LSB) 12 17 DGND NC 13 16 DVCC NC 14 15 CLOCK CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HI5735 Typical Application Circuit +5V HI5735 0.01F VCC (16) D11 D11 (MSB) (1) D10 D10 (2) D9 D9 (3) D8 D8 (4) D7 D7 (5) D6 D6 (6) D5 D5 (7) D4 D4 (8) D3 D3 (9) D2 D2 (10) D1 D1 (11) D0 D0 (LSB) (12) 0.1F (24) CTRL IN (25) CTRL OUT -5.2V (AVEE) (26) REF OUT D/A OUT (21) IOUT 64 64 (20) IOUT (23) RSET 976 (19) ARTN CLK (15) (27) AGND 50 DGND (17, 28) (22) AVEE DVEE (18) 0.01F 0.01F 0.1F 0.1F - 5.2V(AVEE) - 5.2V(DVEE) Functional Block Diagram (LSB) D0 D1 D2 D3 8 LSBs CURRENT CELLS D4 DATA BUFFER/ LEVEL SHIFTER 12-BIT MASTER REGISTER D5 D6 R2R NETWORK ARTN SLAVE REGISTER 227 D7 227 D8 15 D9 15 UPPER 4-BIT DECODER D10 15 SWITCHED CURRENT CELLS IOUT (MSB) D11 IOUT REF CELL CTRL IN CLK + OVERDRIVEABLE VOLTAGE REFERENCE AVEE AGND DVEE 2 DGND VCC - REF OUT RSET 25 CTRL OUT HI5735 Absolute Maximum Ratings Thermal Information Digital Supply Voltage VCC to DGND . . . . . . . . . . . . . . . . . . . +5.5V Negative Digital Supply Voltage DVEE to DGND . . . . . . . . . . -5.5V Negative Analog Supply Voltage AVEE to AGND, ARTN . . . . -5.5V Digital Input Voltages (D11-D0, CLK) to DGND. . . . . DVCC to -0.5V Internal Reference Output Current. . . . . . . . . . . . . . . . . . . . 2.5mA Voltage from CTRL IN to AVEE . . . . . . . . . . . . . . . . . . . . 2.5V to 0V Control Amplifier Output Current . . . . . . . . . . . . . . . . . . . . . 2.5mA Reference Input Voltage Range. . . . . . . . . . . . . . . . . -3.7V to AVEE Analog Output Current (IOUT) . . . . . . . . . . . . . . . . . . . . . . . . . 30mA Thermal Resistance (Typical, Note 1) JA (oC/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Maximum Junction Temperature Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range HI5735KCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on an evaluation PC board in free air. AVEE , DVEE = -4.94 to -5.46V, VCC = +4.75 to +5.25V, VREF = Internal TA = 25oC for All Typical Values Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 12 - - Bits SYSTEM PERFORMANCE Resolution Integral Linearity Error, INL (Note 4) ("Best Fit" Straight Line) - 0.75 1.5 LSB Differential Linearity Error, DNL (Note 4) - 0.5 1.0 LSB Offset Error, IOS (Note 4) - 20 75 A Full Scale Gain Error, FSE (Notes 2, 4) - 1 10 % Offset Drift Coefficient (Note 3) - - 0.05 A/oC - 20.48 - mA (Note 3) -1.25 - 0 V Throughput Rate (Note 5) 80 - - MSPS Output Voltage Full Scale Step Settling Time, tSETT Full Scale To 0.5 LSB Error Band RL = 50 (Note 3) - 20 - ns Single Glitch Area, GE (Peak) RL = 50 (Note 3) - 5 - pV-s - 3 - pV-s Full Scale Output Current, IFS Output Voltage Compliance Range DYNAMIC CHARACTERISTICS Doublet Glitch Area, (Net) Output Slew Rate RL = 50, DAC Operating in Latched Mode (Note 3) - 1,000 - V/s Output Rise Time RL = 50, DAC Operating in Latched Mode (Note 3) - 675 - ps Output Fall Time RL = 50, DAC Operating in Latched Mode (Note 3) - 470 - ps Differential Gain RL = 50 (Note 3) - 0.15 - % Differential Phase RL = 50 (Note 3) - 0.07 - Deg Spurious Free Dynamic Range to Nyquist (Note 3) fCLK = 40MHz, fOUT = 2.02MHz, 20MHz Span - 70 - dBc fCLK = 80MHz, fOUT = 2.02MHz, 40MHz Span - 70 - dBc REFERENCE/CONTROL AMPLIFIER 3 HI5735 AVEE , DVEE = -4.94 to -5.46V, VCC = +4.75 to +5.25V, VREF = Internal TA = 25oC for All Typical Values Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Internal Reference Voltage, VREF (Note 4) -1.27 -1.23 -1.17 V Internal Reference Voltage Drift (Note 3) - 50 - V/oC Internal Reference Output Current Sink/Source Capability (Note 3) -125 - +50 A Internal Reference Load Regulation IREF = 0 to IREF = -125A - 50 - V Input Impedance at REF OUT pin (Note 3) - 1.4 - k Amplifier Large Signal Bandwidth (0.6VP-P) Sine Wave Input, to Slew Rate Limited (Note 3) - 3 - MHz Amplifier Small Signal Bandwidth (0.1VP-P) Sine Wave Input, to -3dB Loss (Note 3) - 10 - MHz Reference Input Impedance (Note 3) - 12 - k Reference Input Multiplying Bandwidth (CTL IN) RL = 50, 100mV Sine Wave, to -3dB Loss at IOUT (Note 3) - 200 - MHz DIGITAL INPUTS (D9-D0, CLK, INVERT) Input Logic High Voltage, VIH (Note 4) 2.0 - - V Input Logic Low Voltage, VIL (Note 4) - - 0.8 V Input Logic Current, IIH (Note 4) - - 400 A Input Logic Current, IIL (Note 4) - - 700 A Digital Input Capacitance, CIN (Note 3) - 3.0 - pF TIMING CHARACTERISTICS Data Setup Time, tSU See Figure 1 (Note 3) 3.0 2.0 - ns Data Hold Time, tHLD See Figure 1 (Note 3) 0.5 0.25 - ns Propagation Delay Time, tPD See Figure 1 (Note 3) - 4.5 - ns CLK Pulse Width, tPW1, tPW2 See Figure 1 (Note 3) 3.0 - - ns POWER SUPPLY CHARACTERISITICS IEEA (Note 4) - 42 50 mA IEED (Note 4) - 70 85 mA ICCD (Note 4) - 13 20 mA Power Dissipation (Note 4) - 650 - mW Power Supply Rejection Ratio VCC 5%, VEE 5% - 5 - A/V NOTES: 2. Gain Error measured as the error in the ratio between the full scale output current and the current through RSET (typically 1.28mA). Ideally the ratio should be 16. 3. Parameter guaranteed by design or characterization and not production tested. 4. All devices are 100% tested at 25oC. 100% production tested at temperature extremes for military temperature devices, sample tested for industrial temperature devices. 5. Dynamic Range must be limited to a 1V swing within the compliance range. 4 HI5735 Timing Diagrams 50% CLK GLITCH AREA = 1/2 (H x W) V D11-D0 HEIGHT (H) 1/2 LSB ERROR BAND IOUT t(ps) WIDTH (W) tPD tSETT FIGURE 1. FULL SCALE SETTLING TIME DIAGRAM tPW1 FIGURE 2. PEAK GLITCH AREA (SINGLET) MEASUREMENT METHOD tPW2 50% CLK tSU tSU tHLD tSU tHLD tHLD D11-D0 tPD IOUT tPD tPD FIGURE 3. PROPAGATION DELAY, SETUP TIME, HOLD TIME AND MINIMUM PULSE WIDTH DIAGRAM 5 HI5735 Typical Performance Curves -1.21 680 CLOCK FREQUENCY DOES NOT ALTER POWER DISSIPATION -1.23 (V) (mW) 640 -1.25 600 -1.27 -1.29 560 -50 -30 -10 10 30 50 70 90 -50 -30 -10 10 30 50 70 90 TEMPERATURE TEMPERATURE FIGURE 4. TYPICAL POWER DISSIPATION OVER TEMPERATURE FIGURE 5. TYPICAL REFERENCE VOLTAGE OVER TEMPERATURE 1.5 0.8 0.5 (LSB) (LSB) 0.4 0.0 -0.5 -0.4 -0.8 1.5 0 600 1200 1800 2400 3000 3600 400 4200 1000 CODE 1600 2200 CODE 2800 3400 4000 FIGURE 7. TYPICAL DNL FIGURE 6. TYPICAL INL ATTEN 20dB RL -10.0dBm 10dB/ MKR -87.33dB -73kHz fC = 10 MSPS 28 (A) 24 S 20 16 C 12 -40 -20 -0 20 40 60 80 100 CENTER 1.237MHz SPAN 2.000MHz TEMPERATURE FIGURE 8. OFFSET CURRENT OVER TEMPERATURE 6 FIGURE 9. SPURIOUS FREE DYNAMIC RANGE = 87.3dBc HI5735 Pin Descriptions PIN NUMBER 1-12 PIN NAME PIN DESCRIPTION D11 (MSB) thru Digital Data Bit 11, the Most Significant Bit thru Digital Data Bit 0, the Least Significant Bit. D0 (LSB) 15 CLK Data Clock Pin DC to 80 MSPS. 13, 14 NC No Connect. 16 VCC Digital Logic Supply +5V. 17, 28 DGND Digital Ground. 18 DVEE -5.2V Logic Supply. 23 RSET External resistor to set the full scale output current. IFS = 16 x (VREF OUT / RSET). Typically 976. 27 AGND Analog Ground supply current return pin. 19 ARTN Analog Signal Return for the R/2R ladder. 21 IOUT Current Output Pin. 20 IOUT Complementary Current Output Pin. 22 AVEE -5.2V Analog Supply. 24 CTRL IN Input to the current source base rail. Typically connected to CTRL OUT and a 0.1F capacitor to AVEE . Allows external control of the current sources. 25 CTRL OUT Control Amplifier Out. Provides precision control of the current sources when connected to CTRL IN such that IFS = 16 x (VREF OUT / RSET). 26 REF OUT -1.23V (typical) bandgap reference voltage output. Can sink up to 125A or be overdriven by an external reference capable of delivering up to 2mA. Detailed Description Clocks and Termination The HI5735 is a 12-bit, current out D/A converter. The DAC can convert at 80 MSPS and runs on +5V and -5.2V supplies. The architecture is an R/2R and segmented switching current cell arrangement to reduce glitch. Laser trimming is employed to tune linearity to true 12-bit levels. The HI5735 achieves its low power and high speed performance from an advanced BiCMOS process. The HI5735 consumes 650mW (typical) and has an improved hold time of only 0.25ns (typical). The internal 12-bit register is updated on the rising edge of the clock. Since the HI5735 clock rate can run to 80 MSPS, to minimize reflections and clock noise into the part, proper termination should be used. In PCB layout clock runs should be kept short and have a minimum of loads. To guarantee consistent results from board to board, controlled impedance PCBs should be used with a characteristic line impedance ZO of 50. Digital Inputs To terminate the clock line, a shunt terminator to ground is the most effective type at a 80 MSPS clock rate. A typical value for termination can be determined by the equation: The HI5735 is a TTL/CMOS compatible D/A. Data is latched by a Master register. Once latched, data inputs D0 (LSB) thru D11 (MSB) are internally translated from TTL to ECL. The internal latch and switching current source controls are implemented in ECL technology to maintain high switching speeds and low noise characteristics. Decoder/Driver The architecture employs a split R/2R ladder and Segmented Current source arrangement. Bits D0 (LSB) thru D7 directly drive a typical R/2R network to create the binary weighted current sources. Bits D8 thru D11 (MSB) pass thru a "thermometer" decoder that converts the incoming data into 15 individual segmented current source enables. This split architecture helps to improve glitch, thus resulting in a more constant glitch characteristic across the entire output transfer function. 7 RT = ZO , for the termination resistor. For a controlled impedance board with a ZO of 50, the RT = 50. Shunt termination is best used at the receiving end of the transmission line or as close to the HI5735 CLK pin as possible. HI5735 DAC ZO = 50 CLK RT = 50 FIGURE 10. CLOCK LINE TERMINATION HI5735 Rise and Fall times and propagation delay of the line will be affected by the Shunt Terminator. The terminator should be connected to DGND. Noise Reduction To reduce power supply noise, separate analog and digital power supplies should be used with 0.1F and 0.01F ceramic capacitors placed as close to the body of the HI5735 as possible on the analog (AVEE) and digital (DVEE) supplies. The analog and digital ground returns should be connected together back at the device to ensure proper operation on power up. The VCC power pin should also be decoupled with a 0.1F capacitor. Reference The internal reference of the HI5735 is a -1.23V (typical) bandgap voltage reference with 50V/oC of temperature drift (typical). The internal reference is connected to the Control Amplifier which in turn drives the segmented current cells. Reference Out (REF OUT) is internally connected to the Control Amplifier. The Control Amplifier Output (CTRL OUT) should be used to drive the Control Amplifier Input (CTRL IN) and a 0.1F capacitor to analog VEE . This improves settling time by providing an AC ground at the current source base node. The Full Scale Output Current is controlled by the REF OUT pin and the set resistor (RSET). The ratio is: IOUT (Full Scale) = (VREF OUT /RSET) x 16. The internal reference (REF OUT) can be overdriven with a more precise external reference to provide better performance over temperature. Figure 11 illustrates a typical external reference configuration. HI5735 -1.25V (26) REF OUT R -5.2V FIGURE 11. EXTERNAL REFERENCE CONFIGURATION Outputs The outputs IOUT and IOUT are complementary current outputs. Current is steered to either IOUT or IOUT in proportion to the digital input code. The sum of the two currents is always equal to the full scale current minus one LSB. The current output can be converted to a voltage by using a load resistor. Both current outputs should have the same load resistor (64 typically). By using a 64 load on the output, a 50 effective output resistance (ROUT) is achieved due to the 227 (15%) parallel resistance seen looking back into the output. This is the nominal value of the R2R ladder of the DAC. The 50 output is needed for matching the output with a 50 line. The load resistor should be chosen so that the effective output resistance (ROUT) matches the line resistance. 8 The output voltage is: VOUT = IOUT x ROUT . IOUT is defined in the reference section. IOUT is not trimmed to 12 bits, so it is not recommended that it be used in conjunction with IOUT in a differential-to-single-ended application. The compliance range of the output is from 1.25V to 0V, with a 1VP-P voltage swing allowed within this range. TABLE 2. INPUT CODING vs CURRENT OUTPUT INPUT CODE (D11-D0) IOUT (mA) IOUT (mA) 1111 1111 1111 -20.48 0 1000 0000 0000 -10.24 -10.24 0000 0000 0000 0 -20.48 Settling Time The settling time of the HI5735 is measured as the time it takes for the output of the DAC to settle to within a 1/2 LSB error band of its final value during a full scale (code 0000... to 1111.... or 1111... to 0000...) transition. All claims made by Intersil with respect to the settling time performance of the HI5735 have been fully verified by the National Institute of Standards and Technology (NIST) and are fully traceable. Glitch The output glitch of the HI5735 is measured by summing the area under the switching transients after an update of the DAC. Glitch is caused by the time skew between bits of the incoming digital data. Typically, the switching time of digital inputs are asymmetrical, meaning that the turn off time is faster than the turn on time (TTL designs). Unequal delay paths through the device can also cause one current source to change before another. In order to minimize this, the Intersil HI5735 employes an internal register, just prior to the current sources, which is updated on the clock edge. Lastly, the worst case glitch on traditional D/A converters usually occurs at the major transition (i.e., code 2047 to 2048). However, due to the split architecture of the HI5735, the glitch is moved to the 255 to 256 transition (and every subsequent 256 code transitions thereafter). This split R/2R segmented current source architecture, which decreases the amount of current switching at any one time, makes the glitch practically constant over the entire output range. By making the glitch a constant size over the entire output range, this effectively integrates this error out of the end application. In measuring the output glitch of the HI5735 the output is terminated into a 64 load. The glitch is measured at any one of the current cell carry (code 255 to 256 transition or any multiple thereof) throughout the DACs output range. The glitch energy is calculated by measuring the area under the voltage-time curve. Figure 13 shows the area considered HI5735 as glitch when changing the DAC output. Units are typically specified in picoVolt-seconds (pV-s). HI5735 100MHz LOW PASS FILTER (21) IOUT Integral Linearity Error, INL, is the measure of the worst case point that deviates from a best fit straight line of data values along the transfer curve. Differential Linearity Error, DNL, is the measure of the error in step size between adjacent codes along the converter's transfer curve. Ideally, the step size is 1 LSB from one code to the next, and the deviation from 1 LSB is known as DNL. A DNL specification of greater than -1 LSB guarantees monotonicity. SCOPE 64 Definition of Specifications 50 Feedthru, is the measure of the undesirable switching noise coupled to the output. FIGURE 12. GLITCH TEST CIRCUIT Applications Output Voltage Full Scale Settling Time, is the time required from the 50% point on the clock input for a full scale step to settle within an 1/2 LSB error band. Bipolar Applications Output Voltage Small Scale Settling Time, is the time required from the 50% point on the clock input for a 100mV step to settle within an 1/2 LSB error band. This is used by applications reconstructing highly correlated signals such as sine waves with more than 5 points per cycle. a (mV) Glitch Area, GE, is the switching transient appearing on the output during a code transition. It is measured as the area under the curve and expressed as a picoVolt*Time specification (typically pV*s). GLITCH ENERGY = (a x t)/2 t (ns) Differential Gain, AV , is the gain error from an ideal sine wave with a normalized amplitude. FIGURE 13. MEASURING GLITCH ENERGY To convert the output of the HI5735 to a bipolar 4V swing, the following applications circuit is recommended. The reference can only provide 125A of drive, so it must be buffered to create the bipolar offset current needed to generate the -2V output with all bits "off". The output current must be converted to a voltage and then gained up and offset to produce the proper swing. Care must be taken to compensate for the voltage swing and error. Differential Phase, , is the phase error from an ideal sine wave. Signal to Noise Ratio, SNR, is the ratio of a fundamental to the noise floor of the analog output. The first 5 harmonics are ignored, and an output filter of 1/2 the clock frequency is used to eliminate alias products. Total Harmonic Distortion, THD, is the ratio of the DAC output fundamental to the RMS sum of the harmonics. The first 5 harmonics are included, and an output filter of 1/2 the clock frequency is used to eliminate alias products. 5k REF OUT (26) - + Spurious Free Dynamic Range, SFDR, is the amplitude difference from a fundamental to the largest harmonically or non-harmonically related spur. A sine wave is loaded into the D/A and the output filtered at 1/2 the clock frequency to eliminate noise from clocking alias terms. - + 5k 1/2 CA2904 1/2 CA2904 0.1F HI5735 60 240 240 50 IOUT (21) - VOUT + HFA1100 FIGURE 14. BIPOLAR OUTPUT CONFIGURATION 9 Intermodulation Distortion, IMD, is the measure of the sum and difference products produced when a two tone input is driven into the D/A. The distortion products created will arise at sum and difference frequencies of the two tones. IMD can be calculated using the following equation: 20Log (RMS of Sum and Difference Distortion Products) IMD = ------------------------------------------------------------------------------------------------------------------------------------------------------- . ( RMS Amplitude of the Fundamental ) HI5735 Die Characteristics PASSIVATION: Type: Sandwich Passivation Undoped Silicon Glass (USG) + Nitride Thickness: USG - 8kA, Nitride - 4.2kA Total 12.2kA +2kA DIE DIMENSIONS: 161.5 mils x 160.7 mils x 19 mils 1 mil METALLIZATION: Type: AlSiCu Thickness: M1 - 8kA, M2 - 17kA DIE ATTACH: Silver Filled Epoxy SUBSTRATE POTENTIAL (POWERED UP): VEED Metallization Mask Layout D9 D10 D11 DGND REF OUT D8 AGND HI5735 CTRL OUT D7 CTRL IN D6 RSET D5 AVEE D4 IOUT D3 IOUT D2 ARTN D1 D0 10 CLK DVCC DGND DVEE HI5735 Small Outline Plastic Packages (SOIC) M28.3 (JEDEC MS-013-AE ISSUE C) N 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA H 0.25(0.010) M B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B C 0.10(0.004) 0.25(0.010) M C A M B S MILLIMETERS MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.6969 0.7125 17.70 18.10 3 E 0.2914 0.2992 7.40 7.60 4 0.05 BSC 10.00 h 0.01 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 8o 0o 28 0o 10.65 - 0.394 N 0.419 1.27 BSC H NOTES: MAX A1 e MIN 28 - 7 8o 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11