WS57C43C HIGH SPEED 4K x 8 CMOS PROM/RPROM KEY FEATURES * Ultra-Fast Access Time * Pin Compatible with 4K x 8 Bipolar PROMs * Immune to Latch-UP -- t ACC = 25 ns -- t CS = 12 ns -- Up to 200 mA * Low Power Consumption * Fast Programming * ESD Protection Exceeds 2000 V * Available in 300 Mil DIP and PLDCC GENERAL DESCRIPTION The WS57C43C is a High Performance 32K UV Erasable Electrically Re-Programmable Read Only Memory (RPROM). It is manufactured in an advanced CMOS technology which enables it to operate at Bipolar PROM speeds while consuming only 25% of the power required by its Bipolar counterparts. A further advantage of the WS57C43C over Bipolar PROM devices is the fact that it utilizes a proven EPROM technology. This enables the entire memory array to be tested for switching characteristics and functionality after assembly. Unlike devices which cannot be erased, every WS5743C in a windowed package is 100% tested with worst case test patterns both before and after assembly. The WS57C43C is configured in the standard Bipolar PROM pinout which provides an easy upgrade path for systems which are currently using Bipolar PROMs, or its predecessor, the WS57C43B. BLOCK DIAGRAM PIN CONFIGURATION TOP VIEW 7 A5 - A11 ROW ADDRESSES ROW DECODER EPROM ARRAY Chip Carrier CERDIP/Plastic DIP 32,768 BITS NC A5 A 6 A 7 5 COLUMN DECODER A0 - A4 COLUMN ADDRESSES SENSE AMPLIFIERS A4 A3 A2 A1 A0 NC O0 CS1/ VPP VCC A8 A9 4 3 2 28 27 26 1 5 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 O1 O2 NC O3 O4 O5 A7 A6 A5 A10 A4 CS1/VPP A3 A11 A2 CS2 A1 NC A0 O7 O0 O6 O1 O2 GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC A8 A9 A10 CS1/VPP A11 CS2 O7 O6 O5 O4 O3 GND CS2 8 OUTPUTS PRODUCT SELECTION GUIDE PARAMETER 57C43C-25 57C43C-35 57C43C-45 57C43C-55 57C43C-70 Address Access Time (Max) 25 ns 35 ns 45 ns 55 ns 70 ns CS to Output Valid Time (Max) 12 ns 20 ns 25 ns 25 ns 25 ns Return to Main Menu 2-31 WS57C43C ABSOLUTE MAXIMUM RATINGS* MODE SELECTION Storage Temperature............................-65 to + 150C CS1/ VPP CS2 VCC OUTPUTS Read VIL VIH VCC DOUT ESD Protection ..................................................> 2000V Output Disable VIH X VCC High Z *NOTICE: Output Disable X VIL VCC High Z Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. Program VPP X VCC DIN Program Verify VIL VIH VCC DOUT Voltage on any Pin with Respect to Ground ....................................-0.6V to +7V VPP with Respect to Ground...................-0.6V to + 14V PINS MODE OPERATING RANGE RANGE TEMPERATURE VCC 0C to +70C +5V 10% Industrial -40C to +85C +5V 10% Military -55C to +125C +5V 10% Commercial DC READ CHARACTERISTICS Over Operating Range. (See Above) SYMBOL PARAMETER TEST CONDITIONS MIN MAX UNITS VIL Input Low Voltage (Note 3) -0.1 0.8 V VIH Input High Voltage (Note 3) 2.0 VCC + 0.3 V VOL Output Low Voltage IOL = 16 mA 0.4 V VOH Output High Voltage IOH = -4 mA VCC Active Current (CMOS) VCC = 5.5 V, f = 0 MHz (Note 1), Output Not Loaded Add 3 mA/MHz for AC Operation VCC Active Current (TTL) VCC = 5.5 V, f = 0 MHz (Note 1), Output Not Loaded Add 3 mA/MHz for AC Operation ICC1 ICC2 V Comm'l 30 mA Industrial 35 mA Military 35 mA Comm'l 40 mA Industrial 50 mA Military 50 mA ILI Input Leakage Current VIN = 5.5V or Gnd -10 10 A ILO Output Leakage Current VOUT = 5.5 V or Gnd -10 10 A NOTES: 2-32 2.4 1. CMOS inputs: GND 0.3V or VCC 0.3V. 2. TTL inputs: VIL 0.8V, VIH 2.0V. 3. These are absolute voltages with respect to device ground pin and include all overshoots due to system and/or tester noise. Do not attempt to test these values without suitable equipment. WS57C43C AC READ CHARACTERISTICS Over Operating Range. (See Above) PARAMETER SYMBOL 57C43C-25 57C43C-35 57C43C-45 57C43C-55 57C43C-70 MIN MAX MIN MAX MIN MAX MIN MAX MIN UNITS MAX Address to Output Delay tACC 25 35 45 55 70 CS1 to Output Delay tCS 12 20 25 25 25 ns Output Disable to Output Float* tDF Address to Output Hold tOH 12 0 25 0 25 25 0 0 25 0 *Sampled, Not 100% Tested. AC READ TIMING DIAGRAM ADDRESSES VALID tACC tOH CS tCS OUTPUTS VALID tDF 2-33 WS57C43C CAPACITANCE (4) TA = 25C, f = 1 MHz PARAMETER CONDITIONS TYP (5) MAX UNITS Input Capacitance VIN = 0V 4 6 pF C OUT Output Capacitance VOUT = 0V 8 12 pF C VPP VPP Capacitance VPP = 0 V 18 25 pF SYMBOL C IN NOTES: 4. This parameter is only sampled and is not 100% tested. 5.Typical values are for TA = 25C and nominal supply voltages. TEST LOAD (High Impedance Test Systems) A.C. TESTING INPUT/OUTPUT WAVEFORM 98 3.0 2.01 V D.U.T. 1.5 0.0 TEST POINTS 1.5 30 pF (INCLUDING SCOPE AND JIG CAPACITANCE) A.C. testing inputs are driven at 3.0 V for a logic "1" and 0.0 V for a logic "0." Timing measurements are made at 1.5 V for input and output transitions in both directions. NOTE: 6. Provide adequate decoupling capacitance as close as possible to this device to achieve the published A.C. and D.C. parameters. A 0.1 microfarad capacitor in parallel with a 0.01 microfarad capacitor connected between VCC and ground is recommended. Inadequate decoupling may result in access time degradation or other transient performance failures. 2-34 WS57C43C NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE TYPICAL ACCESS TIME CHANGE vs. OUTPUT LOADING 1.60 40.0 35.0 1.40 DELTA Taa (ns) NORMALIZED I CC 30.0 1.20 1.00 25.0 20.0 15.0 10.0 0.80 5.0 0.60 0.0 4.0 4.5 5.0 5.5 6.0 0.0 200 SUPPLY VOLTAGE ( V ) 400 600 800 1000 CAPACITANCE ( pF ) NORMALIZED Taa vs. AMBIENT TEMPERATURE NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE 1.6 1.2 1.4 NORMALIZED I CC NORMALIZED Taa 1.1 1.2 1.0 1.0 0.9 0.8 0.6 0.8 -55 -35 -15 5 25 45 65 85 AMBIENT TEMPERATURE (C ) 105 125 -55 -35 -15 5 25 45 65 85 105 125 AMBIENT TEMPERATURE (C) 2-35 WS57C43C PROGRAMMING INFORMATION DC CHARACTERISTICS (TA = 25 5C, VCC = 6.25 V 0.25 V, VPP = 12.75 0.25 V) SYMBOLS PARAMETER MIN MAX UNITS -10 10 A ILI Input Leakage Current (VIN = VCC or Gnd) IPP VPP Supply Current During Programming Pulse 60 mA ICC VCC Supply Current 30 mA VOL Output Low Voltage During Verify (IOL = 16 mA) 0.45 V VOH Output High Voltage During Verify (IOH = -4 mA) 2.4 V NOTES: 8. VPP must not be greater than 13 volts including overshoot. AC CHARACTERISTICS (TA = 25 5C, VCC = 6.25 V 0.25 V, VPP = 12.75 0.25 V) SYMBOLS PARAMETER t AS Address Setup Time t DF Chip Disable Setup Time t DS Data Setup Time t PW Program Pulse Width t DH Data Hold Time t CS Chip Select Delay t RF VPP Rise and Fall Time MIN TYP MAX UNITS 2 s 30 2 s 100 200 2 1 VIH ADDRESS STABLE tAS VIH DATA DATA IN DATA OUT VIL tPW tDS VPP tDH tDF VIH CS1/VPP VIL CS2 tRF VIH DON'T CARE VIL 2-36 tRF ns s PROGRAMMING WAVEFORM VIL s s 30 ADDRESSES ns tCS WS57C43C ORDERING INFORMATION PART NUMBER SPEED (ns) PACKAGE TYPE WS57C43C-25D WS57C43C-25J WS57C43C-25S WS57C43C-25T WS57C43C-35CMB* WS57C43C-35D WS57C43C-35J WS57C43C-35JI WS57C43C-35S WS57C43C-35T WS57C43C-35TMB* WS57C43C-45D WS57C43C-45J WS57C43C-45JI WS57C43C-45S WS57C43C-45T WS57C43C-45TI WS57C43C-45TMB* WS57C43C-55D WS57C43C-55T WS57C43C-55TMB* WS57C43C-70D 25 25 25 25 35 35 35 35 35 35 35 45 45 45 45 45 45 45 55 55 55 70 24 Pin CERDIP, 0.6" 28 Pin PLDCC 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 28 Pad CLLCC, 0.3" 24 Pin CERDIP, 0.6" 28 Pin PLDCC 28 Pin PLDCC 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.6" 28 Pin PLDCC 28 Pin PLDCC 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.6" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.6" OPERATING WSI PACKAGE DRAWING TEMPERATURE MANUFACTURING RANGE PROCEDURE D1 J3 S1 T1 C1 D1 J3 J3 S1 T1 T1 D1 J3 J3 S1 T1 T1 T1 D1 T1 T1 D1 Comm'l Comm'l Comm'l Comm'l Military Comm'l Comm'l Industrial Comm'l Comm'l Military Comm'l Comm'l Industrial Comm'l Comm'l Industrial Military Comm'l Comm'l Military Comm'l Standard Standard Standard Standard MIL-STD-883C Standard Standard Standard Standard Standard MIL-STD-883C Standard Standard Standard Standard Standard Standard MIL-STD-883C Standard Standard MIL-STD-883C Standard NOTE: The actual part marking will not include the initials "WS." *SMD product. See section 4 for DESC SMD numbers. PROGRAMMING/ALGORITHMS/ERASURE/PROGRAMMERS REFER TO PAGE 5-1 The WS57C43C is programmed using Algorithm D shown on page 5-9. Return to Main Menu 2-37