TinyLogic ULP-A 2-Input AND Gate NC7SV08 The NC7SV08 is a single 2-Input AND Gate in tiny footprint packages. The device is designed to operate for VCC = 0.9 V to 3.6 V. www.onsemi.com Features * * * * * * * Designed for 0.9 V to 3.6 V VCC Operation 1.6 ns tPD at 3.3 V (Typ) Inputs/Outputs Over-Voltage Tolerant up to 3.6 V IOFF Supports Partial Power Down Protection Source/Sink 24 mA at 3.3 V Available in SC-88A and MicroPakTM Packages These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant A 1 B 2 GND 3 5 4 VCC Y A 1 6 VCC B 2 5 NC GND 3 MARKING DIAGRAMS SIP6 1.45X1.0 MicroPak CASE 127EB Pin 1 UDFN6 MicroPak2 CASE 517DP Pin 1 CC KK XY Z = Specific Device Code = 2-Digit Lot Run Traceability Code = 2-Digit Date Code = Assembly Plant Code MicroPak SC-88A CASE 419A-02 Figure 1. Pinout Diagrams (Top Views) & B CCKK XYZ 4 Y SC-88A A CCKK XYZ XXXMG G XXX = Specific Devic Code M = Date Code G = Pb-Free Package Y Figure 2. Logic Symbol ORDERING INFORMATION See detailed ordering, marking and shipping information on page 6 of this data sheet. PIN ASSIGNMENT Pin SC-88A FUNCTION TABLE MicroPak 1 A A 2 B B 3 GND GND 4 Y Y 5 VCC N.C. 6 - VCC Output Y = AB Input A B Y L L L L H L H L L H H H N.C. = No Connect (c) Semiconductor Components Industries, LLC, 2002 February, 2021 - Rev. 2 1 Publication Order Number: NC7SV08/D NC7SV08 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +4.3 V VIN DC Input Voltage -0.5 to +4.3 V -0.5 to VCC + 0.5 -0.5 to +4.3 -0.5 to +4.3 V VIN < GND -50 mA VOUT < GND -50 mA VOUT Characteristics DC Output Voltage Active-Mode (High or Low State) Tri-State Mode (Note 1) Power-Down Mode (VCC = 0 V) IIK DC Input Diode Current IOK DC Output Diode Current IOUT DC Output Source/Sink Current 50 mA DC Supply Current per Supply Pin or Ground Pin 50 mA ICC or IGND TSTG -65 to +150 C TL Storage Temperature Range Lead Temperature, 1 mm from Case for 10 Seconds 260 C TJ Junction Temperature Under Bias +150 C qJA Thermal Resistance (Note 2) SC-88A MicroPak 377 154 C/W PD Power Dissipation in Still Air SC-88A MicroPak 332 812 mW Level 1 - MSL Moisture Sensitivity FR Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in - ESD Withstand Voltage (Note 3) Human Body Model Charged Device Model 4000 2000 V 100 mA VESD ILatchup Latchup Performance (Note 4) Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Applicable to devices with outputs that may be tri-stated. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow per JESD51-7. 3. HBM tested to EIA / JESD22-A114-A. CDM tested to JESD22-C101-A. JEDEC recommends that ESD qualification to EIA/JESD22-A115A (Machine Model) be discontinued. 4. Tested to EIA/JESD78 Class II. www.onsemi.com 2 NC7SV08 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Positive DC Supply Voltage VIN DC Input Voltage VOUT TA tr , tf DC Output Voltage Min Max Unit 0.9 3.6 V 0 3.6 V 0 0 0 VCC 3.6 3.6 -40 +85 C 0 10 ns/V Active-Mode (High or Low State) Tri-State Mode (Note 1) Power-Down Mode (VCC = 0 V) Operating Temperature Range Input Transition Rise and Fall Time VCC = 3.3 V 0.3 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. DC ELECTRICAL CHARACTERISTICS TA = 255C Symbol VIH VIL VOH Parameter Condition High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage VCC (V) TA = -405C to +855C Min Typ Max Min Max Unit V 0.9 - 0.5 - - - 1.1 to 1.3 0.65 x VCC - - 0.65 x VCC - 1.4 to 1.6 0.65 x VCC - - 0.65 x VCC - 1.65 to 1.95 0.65 x VCC - - 0.65 x VCC - 2.3 to <2.7 1.6 - - 1.6 - 2.7 to 3.6 2.0 - - 2.0 - 0.9 - 0.5 - - - 1.1 to 1.3 - - 0.35 x VCC - 0.35 x VCC 1.4 to 1.6 - - 0.35 x VCC - 0.35 x VCC 1.65 to 1.95 - - 0.35 x VCC - 0.35 x VCC 2.3 to <2.7 - - 0.7 - 0.7 2.7 to 3.6 - - 0.8 - 0.8 VIN = VIH or VIL V 0.9 - VCC - 0.1 - - - 1.1 to 1.3 VCC - 0.1 - - VCC - 0.1 - 1.4 to 1.6 VCC - 0.1 - - VCC - 0.1 - 1.65 to 1.95 VCC - 0.2 - - VCC - 0.2 - 2.3 to <2.7 VCC - 0.2 - - VCC - 0.2 - 2.7 to 3.6 VCC - 0.2 - - VCC - 0.2 - IOH = -2 mA 1.1 o 1.3 0.75 x VCC - - 0.75 x VCC - IOH = -4 mA 1.4 to 1.6 0.75 x VCC - - 0.75 x VCC - IOH = -6 mA 1.65 to 1.95 1.25 - - 1.25 - IOH = -100 mA 2.3 to <2.7 2.0 - - 2.0 - IOH = -12 mA 2.3 to <2.7 1.8 - - 1.8 - 2.7 to 3.6 2.2 - - 2.2 - IOH = -18 mA 2.3 to <2.7 1.7 - - 1.7 - 2.7 to 3.6 2.4 - - 2.4 - 2.7 to 3.6 2.2 - - 2.2 - IOH = -24 mA V www.onsemi.com 3 NC7SV08 DC ELECTRICAL CHARACTERISTICS (continued) TA = -405C to +855C TA = 255C Symbol VOL Parameter Condition Low-Level Output Voltage VIN = VIH or VIL Min VCC (V) Typ Max Min Max V 0.9 - 0.1 - - - 1.1 to 1.3 - - 0.1 - 0.1 1.4 to 1.6 - - 0.1 - 0.1 1.65 to 1.95 - - 0.2 - 0.2 2.3 to < 2.7 - - 0.2 - 0.2 2.7 to 3.6 - - 0.2 - 0.2 IOL = 2 mA 1.1 o 1.3 - - 0.25 x VCC - 0.25 x VCC IOL = 4 mA 1.4 to 1.6 - - 0.25 x VCC - 0.25 x VCC IOL = 6 mA 1.65 to 1.95 - - 0.3 - 0.3 IOL = 12 mA 2.3 to <2.7 - - 0.4 - 0.4 2.7 to 3.6 - - 0.4 - 0.4 2.3 to <2.7 - - 0.6 - 0.6 2.7 to 3.6 - - 0.4 - 0.4 IOL = 100 mA IOL = 18 mA Unit IOL = 24 mA 2.7 to 3.6 - - 0.55 - 0.55 Input Leakage Current VIN = 0 V to 3.6 V 0.9 to 3.6 - - 0.1 - 0.5 mA IOFF Power Off Leakage Current VIN = 0 V to 3.6 V or VOUT = 0 V to 3.6 V 0 - - 0.5 - 0.5 mA ICC Quiescent Supply Current VIN = VCC or GND 0.9 to 3.6 - - 0.9 - 0.9 mA IIN Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIII IIIIIII IIIII IIIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIII IIIIII III III III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII AC ELECTRICAL CHARACTERISTICS TA = 25C Symbol tPLH, tPHL Condition VCC (V) RL = 1 MW, CL = 15 pF 0.9 - 15.9 - - - RL = 2 kW, CL = 15 pF 1.1 to 1.3 - 6.8 11.6 - 14.6 1.4 to 1.6 - 3.6 6.0 - 7.2 1.65 to 1.95 - 2.6 4.5 - 5.3 2.3 to 2.7 - 1.9 2.6 - 3.7 2.7 to 3.6 - 1.6 2.3 - 3.0 Parameter Propagation Delay, (A or B) to Y (Figures 3 and 4) TA = -405C to +855C Min RL = 500 W, CL = 30 pF Typ Max Min Max Unit ns CAPACITIVE CHARACTERISTICS Symbol Parameter Test Condition Typical (TA = 25C) Unit CIN Input Capacitance VCC = 0 V 2.0 pF CPD Power Dissipation Capacitance (Note 5) f = 10 MHz, VCC = 0.9 to 3.6 V, VIN = 0 V or VCC 8.0 pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD VCC2 fin + ICC VCC. www.onsemi.com 4 NC7SV08 OPEN 2 x VCC GND R1 INPUT OUTPUT DUT RL RT Test Switch Position tPLH / tPHL Open tPLZ / tPZL 2 x VCC tPHZ / tPZH GND CL * CL includes probe and jig capacitance RT is ZOUT of pulse generator (typically 50 W) f = 1 MHz Figure 3. Test Circuit tr = 3 ns tf = 3 ns 90% 90% Vmi INPUT Vmi INPUT Vmi 10% 10% tPHL Vmi GND GND tPZL tPLH Vmo OUTPUT VCC VCC tPLZ VOH Vmo OUTPUT Vmo VOL + VY VOL VOL tPLH tPHL Vmo OUTPUT tPZH VOH Vmo ~VCC tPHZ VOH VOH - VY Vmo OUTPUT VOL ~0 V VCC, V Vmi, V Vmo, V VY, V 0.9 VCC / 2 VCC / 2 0.1 1.1 to 1.3 VCC / 2 VCC / 2 0.1 1.4 to 1.6 VCC / 2 VCC / 2 0.1 1.65 to 1.95 VCC / 2 VCC / 2 0.15 2.3 to 2.7 VCC / 2 VCC / 2 0.15 3.0 to 3.6 1.5 1.5 0.3 Figure 4. Switching Waveforms www.onsemi.com 5 NC7SV08 ORDERING INFORMATION Package Marking Pin 1 Orientation (See below) Shipping SC-88A V08 Q4 3000 / Tape & Reel NC7SV08L6X MicroPak G3 Q4 5000 / Tape & Reel NC7SV08FHX MicroPak2 G3 Q4 5000 / Tape & Reel Device NC7SV08P5X For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Pin 1 Orientation in Tape and Reel MicroPak is trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 6 NC7SV08 PACKAGE DIMENSIONS SIP6 1.45X1.0 CASE 127EB ISSUE O www.onsemi.com 7 NC7SV08 PACKAGE DIMENSIONS UDFN6 1.0X1.0, 0.35P CASE 517DP ISSUE O www.onsemi.com 8 NC7SV08 PACKAGE DIMENSIONS SC-88A (SC-70-5/SOT-353) CASE 419A-02 ISSUE L A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 -B- S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) B M M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J C K H SOLDER FOOTPRINT 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 9 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative