TS1003DB - SILICON LABS - Datasheet.Directory

TS1003 Demo Board

Page 1

REVISION NOTE

The current revisions for the TS1003 Demo Boards

display the identifier TS100x Demo Board on the

top side of the evaluation board as depicted in

Figure 1. If the identifier is not printed on the top

side of the evaluation board, please contact Silicon

Labs for support at:

https://www.silabs.com/support/pages/contacttechnicalsu

pport.aspx

COMPONENT LIST

DESIGNATION QTY DESCRIPTION

C1, C2, C3, C5 4 0.1µF ± 10%

capacitors (0805)

C4, C6 2 1µF ±10%

capacitors (0805)

R2 1 665kΩ ± 1%

resistor (0805)

R7 1 500kΩ ± 1%

resistor (0805)

R5, R6, R10 3 1MΩ ± 1%

resistors (0805)

R8, R9 2 1.25MΩ ± 1%

resistors (0805)

R1, R3, R4 3 2MΩ ± 1%

resistors (0805)

U1, U2 2 TS1003

operational

amplifiers

out

,GND 11 Test points

FEATURES

 0.8V to 5.5V Single-supply operation

 AC-coupled Non-Inverting and Inverting

configuration supplied

 Fully Assembled and Tested

 2in x 2in 2-layer demo board

DESCRIPTION

The demo board for the TS1003 is a completely

assembled and tested circuit board that can be used

for evaluating the TS1003. The TS1003 is the

industry’s first sub-1µA supply current, precision

CMOS operational amplifier fully specified to operate

over a supply voltage range from 0.8V to 5.5V. Fully

specified at 1.8V, the TS1003 is optimized for ultra-

long-life battery powered applications. The TS1003

exhibits a typical input bias current of 2pA, and rail-to-

rail input and output stages.

The TS1003 is fully specified over the industrial

temperature range (-40°C to +85°C). The TS1003

evaluation board is offered with either a PCB-space

saving 5-lead SC70 or 5-lead SOT23 p ackaging.

Product data sheets and additional documentation

can be found at www.silabs.com.

Ordering Information

Order Number Description

TS1003DB SC70 Packaging

Demo Board

TS1003DB-SOT SOT23 Packaging

Demo Board

Figure 1. TS1003 Evaluation Board Top View Figure 2. TS1003 Evaluation Board Bottom View

TS1003 Demo Board

TS1003-EVB Rev. 1.0 Page 2

Description

The TS1003 evaluation boards provide two

configurations for evaluating the TS1003 operational

amplifier in one single PCB board, namely a non-

inverting configuration located on the left-hand side of

the board and an inverting configuration located on

the right-hand side of the board. In both cases, the

input to each circuit is AC-coupled. The demo board

provides a re-biasing scheme at one-half the power

supply or VDD/2 for the inverting configuration and at

VDD/4 for the non-inverting configuration.

The TS1003 demo board provides a dedicated power

supply for the non-inverting circuit and a dedicated

power supply for the inverting circuit. This provides

the user the flexibility of evaluating one circuit at a

time or both at the same time.

In both the non-inverting and the inverting

configuration, the AC-coupling capacitor creates a

high pass filter. The resulting cut-off frequency, fC, is

given as:

fC= 1

2πRC

In the non-inverting circuit, R=R5=1MΩ and

C=C5=0.1µF. In the inverting case, R=R10=1MΩ and

C=C1=0.1µF. In both cases, these component values

generate a high-pass cut-off frequen cy of 1.6Hz.

Default Configurations

Non-Inverting configuration

In the non-inverting configuration, the circuit’s transfer

function is given by the following equation:

VOUT

VIN = 1+ R4

With R4=2MΩ and R3=2MΩ the circuit signal gain is

2 with a circuit bandwidth of 2kHz. This results in an

overall circuit bandwidth range of 1.6Hz to 2kHz.

Inverting configuration

In an inverting configuration, the circuit’s transfer

function is given by the following equation:

VOUT

VIN = -R6

R10

In this case, R6=1MΩ and R10=1MΩ. This results in

a signal gain of -1 with a circuit bandwidth of 2kHz

and an overall circuit bandwidth range of 1.6Hz to

2kHz.

Quick Start Procedures

Required Equipment

 TS1003 demo board

 DC Power Supply, Single or Dual Output

 Function Generator

 4-channel Oscilloscope

 Two 1MΩ oscilloscope probes

Non-Inverting Configuration

In order to evaluate the TS1003 operational amplifier

in the non-inverting configuration, the following steps

are to be performed:

1) Before connecting the DC power supply to the

demo board power test points, turn on the power

supply and set the DC voltage to 5.5V and then

turn it off.

2) Set the function generator frequency to 500Hz

and output level with a VOH = 2.35V and a VOL =

2.15V. This sets the input signal swing to

200mVPP, centered at 2.25V.

3) In order to monitor the input and output signal,

select two channels on the oscilloscope and set

the vertical voltage scale and the vertical position

on each channel to 100mV/DIV and -2.25V,

respectively. Set the horizontal time scale to

500µs/DIV.

4) Connect the positive terminal of the DC power

supply to VDD and the ground terminal to GND.

TS1003 Demo Board

TS1003-EVB Rev. 1.0 Page 3

5) Connect the signal output of the function

generator to V

and the ground terminal to GND.

6) To monitor the input, connect the signal terminal

of one of the oscilloscope probes to V

and the

ground terminal to GND. To monitor the output,

use the second probe to connect the signal

terminal to V

OUT

and the ground terminal to GND.

7) Turn on the power supply and check that the

power supply current is approximately 3.6µA.

8) Turn on the function generator.

9) Observe the input and output signal. The output

signal is an amplified version of the input signal

with an output swing of approximately 400mV

corresponding to a signal gain of two.

Inverting Configuration

In order to evaluate the TS1003 operational amplifier

in the inverting configuration, the following steps are

to be performed:

1) Before connecting the DC power supply to the

demo board, turn on the power supply and set

the DC voltage to 5.5V and then turn it off.

2) Set the function generator output frequency to

500Hz and output level with a V

= 2.35V and a

= 2.15V. This sets the input swing to

200mV

, centered at 2.25V.

3) In order to monitor the input and output signal,

select two channels on the oscilloscope and set

the vertical voltage scale and the vertical position

on each channel to 100mV/DIV and -2.25V,

respectively. Set the horizontal time scale to

500µs/DIV.

4) Connect the positive terminal of the DC power

supply to VDD and the ground terminal to GND.

5) Connect the signal output of the function

generator to V

and the ground terminal to GND.

6) To monitor the input, connect the signal terminal

of one of the oscilloscope probes to V

and the

ground terminal to GND. To monitor the output,

use the second probe to connect the signal

terminal to V

OUT

and the ground terminal to GND.

7) Turn on the power supply and check that the

power supply current is approximately 3.0µA.

8) Turn on the function generator.

9) Observe the input and output signal. The output

signal is an inverted version of the input signal

and the swing should be 200mV

Figure 4. Inverting Configuration

Figure 3. Non-Inverting Configuration

TS1003 Demo Board

Silicon Laboratories, Inc. Page 4

400 West Cesar Chavez, Austin, TX 78701 TS1003-EVB Rev. 1.0

+1 (512) 416–8500 ▪ www.silabs.com

Figure 5. TS1003 Demo Board

Top Layer #1

Figure 6. TS1003 Demo Board

Top Layer #2

Figure 7. TS1003 Demo Board

Bottom Layer (GND) #1

Figure 8. TS1003 Demo Board

otto

m L

aye

)

Disclaimer

Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers

using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific

device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories

reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy

or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply

or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific

written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected

to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no

circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.

Trademark Information

Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations

thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,

USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of

ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.

http://www.silabs.com

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA

Smart.

Connected.

Energy-Friendly

Products

www.silabs.com/products Quality

www.silabs.com/quality Support and Community

community.silabs.com