LTC2488 16-Bit 2-/4-Channel ADC with Easy Drive Input Current Cancellation FEATURES DESCRIPTION Up to 2 Differential or 4 Single-Ended Inputs Easy Drive Technology Enables Rail-to-Rail Inputs with Zero Differential Input Current Directly Digitizes High Impedance Sensors with Full Accuracy 600nV RMS Noise (0.02LSB Transition Noise) GND to VCC Input/Reference Common Mode Range Simultaneous 50Hz/60Hz Rejection 2ppm INL, No Missing Codes 1ppm Offset and 15ppm Full-Scale Error No Latency: Digital Filter Settles in a Single Cycle, Even After a New Channel is Selected Single Supply 2.7V to 5.5V Operation (0.8mW) Internal Oscillator Tiny 4mm x 3mm DFN Package The LTC(R)2488 is a 4-channel (2-channel differential), 16bit, No Latency TM ADC with Easy DriveTM technology. The patented sampling scheme eliminates dynamic input current errors and the shortcomings of on-chip buffering through automatic cancellation of differential input current. This allows large external source impedances and rail-torail input signals to be directly digitized while maintaining exceptional DC accuracy. The LTC2488 includes an integrated oscillator. This device can be configured to measure an external signal from combinations of 4 analog input channels operating in single ended or differential modes. It automatically rejects line frequencies of 50Hz and 60Hz simultaneously. The LTC2488 allows a wide common mode, input range (0V to VCC), independent of the reference voltage. Any combination of single-ended or differential inputs can be selected and the first conversion after a new channel selection is valid. APPLICATIONS Direct Sensor Digitizer Direct Temperature Measurement Instrumentation Industrial Process Control L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and No Latency and Easy Drive are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Data Acquisition System Fullscale Error vs Source Resistance 80 2.7V TO 5.5V CH3 COM IN+ REF+ 16-BIT ADC WITH EASY DRIVE IN- REF- SDI SCK SDO CS 0.1F 4-WIRE SPI INTERFACE +FS ERROR (ppm) 4-CHANNEL MUX CH2 10F VCC CH0 CH1 VCC = 5V = 5V 60 VREF VIN+ = 3.75V - = 1.25V 40 VIN FO = GND 20 TA = 25C CIN = 1F 0 -20 -40 -60 FO OSC 2488 TA01a -80 1 10 100 1k RSOURCE () 10k 100k 2488 TA01b 2488fa 1 LTC2488 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Notes 1, 2) Supply Voltage (VCC) ................................... -0.3V to 6V Analog Input Voltage (CH0 to CH3, COM) ..................-0.3V to (VCC + 0.3V) REF+, REF- ................................-0.3V to (VCC + 0.3V) Digital Input Voltage......................-0.3V to (VCC + 0.3V) Digital Output Voltage ...................-0.3V to (VCC + 0.3V) Operating Temperature Range LTC2488C ................................................ 0C to 70C LTC2488I ............................................. -40C to 85C Storage Temperature Range................... -65C to 150C FO 1 14 REF- SDI 2 13 REF+ SCK 3 CS 4 12 VCC 11 CH3 15 SDO 5 10 CH2 GND 6 9 CH1 COM 7 8 CH0 DE PACKAGE 14-LEAD (4mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 37C/W EXPOSED PAD (PIN 15) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2488CDE#PBF LTC2488CDE#TRPBF 2488 14-Lead (4mm x 3mm) Plastic DFN 0C to 70C LTC2488IDE#PBF LTC2488IDE#TRPBF 2488 14-Lead (4mm x 3mm) Plastic DFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 3, 4) PARAMETER CONDITIONS Resolution (No Missing Codes) 0.1V VREF VCC, -FS VIN +FS (Note 5) MIN TYP MAX Integral Nonlinearity 5V VCC 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6) 2.7V VCC 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6) 2 1 20 Offset Error 2.5V VREF VCC, GND IN+ = IN- VCC (Note 14) 0.5 5 Offset Error Drift 2.5V VREF VCC, GND IN+ = IN- VCC Positive Full-Scale Error 2.5V VREF VCC, IN+ = 0.75VREF, IN- = 0.25VREF Positive Full-Scale Error Drift 2.5V VREF VCC, IN+ = 0.75VREF, IN- = 0.25VREF Negative Full-Scale Error 2.5V VREF VCC, IN+ = 0.25VREF, IN- = 0.75VREF Negative Full-Scale Error Drift 2.5V VREF VCC, IN+ = 0.25VREF, IN- = 0.75VREF 0.1 ppm of VREF/C Total Unadjusted Error 5V VCC 5.5V, VREF = 2.5V, VIN(CM) = 1.25V 5V VCC 5.5V, VREF = 5V, VIN(CM) = 2.5V 2.7V VCC 5.5V, VREF = 2.5V, VIN(CM) = 1.25V 15 15 15 ppm of VREF ppm of VREF ppm of VREF Output Noise 2.7V < VCC < 5.5V, 2.5V VREF VCC, GND IN+ = IN- VCC (Note 13) 0.6 VRMS 16 UNITS Bits 10 V nV/C 32 0.1 ppm of VREF ppm of VREF ppm of VREF ppm of VREF/C 32 ppm of VREF 2488fa 2 LTC2488 CONVERTER CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) PARAMETER CONDITIONS Input Common Mode Rejection DC 2.5V VREF VCC, GND IN+ = IN- VCC (Note 5) 140 dB Input Common Mode Rejection 50Hz 2% 2.5V VREF VCC, GND IN+ = IN- VCC (Note 5) 2.5V VREF VCC, GND IN+ = IN- VCC (Note 5) 2.5V VREF VCC, GND IN+ = IN- VCC (Notes 5, 7) 2.5V VREF VCC, GND IN+ = IN- VCC (Notes 5, 8) 2.5V VREF VCC, GND IN+ = IN- VCC (Notes 5, 9) 2.5V VREF VCC, GND IN+ = IN- VCC (Note 5) VREF = 2.5V, IN+ = IN- = GND VREF = 2.5V, IN+ = IN- = GND (Notes 7, 9) VREF = 2.5V, IN+ = IN- = GND (Notes 8, 9) 140 dB 140 dB 110 120 dB 110 120 dB Input Common Mode Rejection 60Hz 2% Input Normal Mode Rejection 50Hz 2% Input Normal Mode Rejection 60Hz 2% Input Normal Mode Rejection 50Hz/60Hz 2% Reference Common Mode Rejection DC Power Supply Rejection DC Power Supply Rejection, 50Hz 2% Power Supply Rejection, 60Hz 2% MIN 87 120 TYP MAX UNITS dB 140 dB 120 dB 120 dB 120 dB ANALOG INPUT AND REFERENCE The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER IN+ Absolute/Common Mode IN+ Voltage (IN+ Corresponds to the Selected Positive Input Channel) CONDITIONS MIN GND - 0.3V VCC + 0.3V V IN- Absolute/Common Mode IN- Voltage (IN- Corresponds to the Selected Negative Input Channel) GND - 0.3V VCC + 0.3V V VIN Input Differential Voltage Range (IN+ - IN-) -FS +FS FS Full Scale of the Differential Input (IN+ - IN-) 0.5VREF LSB Least Significant Bit of the Output Code FS/216 REF+ Absolute/Common Mode REF+ Voltage 0.1 REF- Absolute/Common Mode REF- Voltage VREF Reference Voltage Range (REF+ - REF-) CS(IN+) IN+ Sampling Capacitance 11 pF CS(IN-) IN- Sampling Capacitance 11 pF CS(VREF) VREF Sampling Capacitance IDC_LEAK(IN+) IN+ DC Leakage Current Sleep Mode, IN+ = GND IDC_LEAK(IN-) IN- DC Leakage Current Sleep Mode, IN- = GND IDC_LEAK(REF+) IDC_LEAK(REF-) REF+ DC Leakage Current Sleep Mode, REF+ = V REF- DC Leakage Current Sleep Mode, REF- = GND tOPEN MUX Break-Before-Make QIRR MUX Off Isolation TYP MAX VIN = 2VP-P DC to 1.8MHz V V V GND VCC + REF - 0.1V 0.1 VCC V 11 CC UNITS -10 1 -10 -100 -100 V pF 10 nA 1 10 nA 1 100 nA 1 100 nA 50 ns 120 dB 2488fa 3 LTC2488 DIGITAL INPUTS AND DIGITAL OUTPUTS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS VIH 2.7V VCC 5.5V (Note 18) VIL High Level Input Voltage (CS, FO, SDI) S , FO, SDI) Low Level Input Voltage (C 2.7V VCC 5.5V VIH High Level Input Voltage (SCK) 2.7V VCC 5.5V (Notes 10, 15) VIL Low Level Input Voltage (SCK) S , FO, SDI) Digital Input Current (C 2.7V VCC 5.5V (Notes 10, 15) 0V VIN VCC -10 -10 IIN IIN Digital Input Current (SCK) S, FO, SDI) Digital Input Capacitance (C 0V VIN VCC (Notes 10, 15) CIN MIN CIN Digital Input Capacitance (SCK) (Notes 10, 15) VOH High Level Output Voltage (SDO) IO = -800A VOL Low Level Output Voltage (SDO) IO = 1.6mA VOH High Level Output Voltage (SCK) IO = -800A (Notes 10, 17) VOL Low Level Output Voltage (SCK) IO = 1.6mA (Notes 10, 17) IOZ Hi-Z Output Leakage (SDO) TYP MAX UNITS VCC - 0.5 V 0.5 V VCC - 0.5 V 0.5 V 10 A 10 A 10 pF 10 pF VCC - 0.5 V 0.4 V VCC - 0.5 V -10 0.4 V 10 A POWER REQUIREMENTS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER VCC Supply Voltage ICC Supply Current CONDITIONS MIN Conversion Current (Note 12) Sleep Mode (Note 12) TYP 2.7 160 1 MAX UNITS 5.5 V 275 2 A A 2488fa 4 LTC2488 DIGITAL INPUTS AND DIGITAL OUTPUTS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) SYMBOL PARAMETER CONDITIONS fEOSC External Oscillator Frequency Range (Note 16) MAX UNITS MIN 10 tHEO tLEO tCONV Conversion Time Simultaneous 50Hz/60Hz External Oscillator fISCK Internal SCK Frequency Internal Oscillator (Notes 10, 17) External Oscillator (Notes 10, 11, 15) TYP 4000 kHz External Oscillator High Period 0.125 100 s External Oscillator Low Period 0.125 100 s 144.1 149.9 ms ms 146.9 41036/fEOSC (in kHz) 38.4 fEOSC/8 kHz kHz DISCK Internal SCK Duty Cycle (Notes 10, 17) fESCK External SCK Frequency Range (Notes 10, 11, 15) tLESCK External SCK Low Period (Notes 10, 11, 15) 125 ns tHESCK External SCK High Period (Notes 10, 11, 15) 125 ns tDOUT_ISCK Internal SCK 24-Bit Data Output Time Internal Oscillator (Notes 10, 17) External Oscillator (Notes 10, 11, 15) 0.61 tDOUT_ESCK t1 External SCK 24-Bit Data Output Time CS to SDO Low 0 200 ns t2 CS to SDO High Z 0 200 ns t3 CS to SCK Internal SCK Mode 0 200 ns External SCK Mode 50 45 0.625 192/fEOSC (in kHz) 55 % 4000 kHz 0.64 24/fESCK (in kHz) t4 CS to SCK tKQMAX SCK to SDO Valid tKQMIN SDO Hold After SCK S SCK Set-Up Before C (Note 5) t5 t7 SDI Setup Before SCK t8 SDI Hold After SCK ms ms ms ns 200 ns 15 ns 50 ns (Note 5) 100 ns (Note 5) 100 ns Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to GND. Note 3: Unless otherwise specified: VCC = 2.7V to 5.5V VREFCM = VREF/2, FS = 0.5VREF VIN = IN+ - IN-, VIN(CM) = (IN+ - IN-)/2, where IN+ and IN- are the selected input channels. Note 4: Use internal conversion clock or external conversion clock source with fEOSC = 307.2kHz unless other wise specified. Note 5: Guaranteed by design, not subject to test. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 7: fEOSC = 256kHz 2% (external oscillator). Note 8: fEOSC = 307.2kHz 2% (external oscillator). Note 9: Simultaneous 50Hz/60Hz (internal oscillator) or fEOSC = 280kHz 2% (external oscillator). Note 10: The SCK can be configured in external SCK mode or internal SCK mode. In external SCK mode, the SCK pin is used as a digital input and the driving clock is fESCK. In the internal SCK mode, the SCK pin is used as a digital output and the output clock signal during the data output is fISCK. Note 11: The external oscillator is connected to the FO pin. The external oscillator frequency, fEOSC, is expressed in kHz. Note 12: The converter uses its internal oscillator. Note 13: The output noise includes the contribution of the internal calibration operations. VREF VCC. Note 14: Guaranteed by design and test correlation. Note 15: The converter is in external SCK mode of operation such that the SCK pin is used as a digital input. The frequency of the clock signal driving SCK during the data output is fESCK and is expressed in Hz. Note 16: Refer to Applications Information section for performance vs data rate graphs. Note 17: The converter in internal SCK mode of operation such that the SCK pin is used as a digital output. Note 18: For VCC < 3V, VIH is 2.5V for pin fO. 2488fa 5 LTC2488 TYPICAL PERFORMANCE CHARACTERISTICS Integral Nonlinearity (VCC = 5V, VREF = 5V) -45C 1 2 INL (ppm OF VREF) 2 25C 0 85C -1 -2 3 VCC = 5V VREF = 2.5V VIN(CM) = 1.25V FO = GND 1 2 -45C, 25C, 85C 0 -1 -2 -3 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 INPUT VOLTAGE (V) 2 -3 -1.25 2.5 -0.75 12 8 85C 25C 4 0 -45C -4 -8 -12 -2.5 -2 -1.5 -1 -0.5 0 0.5 1 1.5 INPUT VOLTAGE (V) 2 VCC = 5V VREF = 2.5V VIN(CM) = 1.25V FO = GND 12 85C 25C -45C 0 -4 -0.75 -0.2 0 1 3 2 VIN(CM) (V) 4 5 6 2488 G07 -0.75 0.2 VCC = 5V VREF = 5V VIN = 0V FO = GND 0.1 0 -0.3 -45 -30 -15 1.25 -0.25 0.25 0.75 INPUT VOLTAGE (V) 2488 G06 Offset Error vs VCC 0.2 0.1 REF+ = 2.5V REF- = GND VIN = 0V VIN(CM) = GND TA = 25C 0 -0.1 -0.2 -1 -4 0.3 -0.1 -0.1 -45C 0 -12 -1.25 1.25 -0.25 0.25 0.75 INPUT VOLTAGE (V) OFFSET ERROR (ppm OF VREF) OFFSET ERROR (ppm OF VREF) OFFSET ERROR (ppm OF VREF) 0 1.25 2488 G03 85C 25C 4 Offset Error vs Temperature 0.3 0.1 VCC = 2.7V VREF = 2.5V VIN(CM) = 1.25V FO = GND 2488 G05 Offset Error vs VIN(CM) 0.2 -0.25 0.25 0.75 INPUT VOLTAGE (V) -8 2488 G04 -0.3 8 4 -12 -1.25 2.5 VCC = 5V VREF = 5V VIN = 0V TA = 25C -0.75 Total Unadjusted Error (VCC = 2.7V, VREF = 2.5V) -8 0.3 -1 Total Unadjusted Error (VCC = 5V, VREF = 2.5V) TUE (ppm OF VREF) TUE (ppm OF VREF) 8 -45C, 25C, 85C 0 2488 G02 Total Unadjusted Error (VCC = 5V, VREF = 5V) VCC = 5V VREF = 5V VIN(CM) = 2.5V FO = GND 1 -3 -1.25 1.25 -0.25 0.25 0.75 INPUT VOLTAGE (V) 2488 G01 12 VCC = 2.7V VREF = 2.5V VIN(CM) = 1.25V FO = GND -2 TUE (ppm OF VREF) INL (ppm OF VREF) 3 VCC = 5V VREF = 5V VIN(CM) = 2.5V FO = GND Integral Nonlinearity (VCC = 2.7V, VREF = 2.5V) INL (ppm OF VREF) 3 Integral Nonlinearity (VCC = 5V, VREF = 2.5V) 0 15 30 45 60 TEMPERATURE (C) 75 90 2488 G08 -0.2 -0.3 2.7 3.1 3.5 3.9 4.3 VCC (V) 4.7 5.1 5.5 2488 G09 2488fa 6 LTC2488 TYPICAL PERFORMANCE CHARACTERISTICS On-Chip Oscillator Frequency vs Temperature Offset Error vs VREF 0.1 0 -0.1 308 308 306 304 302 -0.2 -0.3 310 0 1 2 3 VREF (V) 300 -45 -30 -15 5 4 VCC = 4.1V VREF = 2.5V VIN = 0V VIN(CM) = GND FO = GND -20 -40 REJECTION (dB) REJECTION (dB) 75 90 -60 -80 VCC = 4.1V DC 1.4V VREF = 2.5V IN+ = GND IN- = GND FO = GND TA = 25C -60 -80 -140 0 20 40 60 80 100 120 140 160 180 200 220 FREQUENCY AT VCC (Hz) 2488 G13 140 VCC = 2.7V 120 1.2 VCC = 5V 0.8 VCC = 2.7V 0.4 0 15 30 45 60 TEMPERATURE (C) 75 90 2488 G16 0 -45 -30 -15 250 VCC = 5V VCC = 3V 200 150 0.2 100 -45 -30 -15 VREF = VCC IN+ = GND IN- = GND 400 SCK = NC SDO = NC 350 SDI = GND CS GND F = EXT OSC 300 O TA = 25C 450 1.0 0.6 30800 500 FO = GND 1.8 CS = VCC SCK = NC 1.6 SDO = NC 1.4 SDI = GND SUPPLY CURRENT (A) 160 30700 30750 FREQUENCY AT VCC (Hz) Conversion Current vs Output Data Rate 2.0 VCC = 5V 30650 2488 G15 Sleep Mode Current vs Temperature SLEEP MODE CURRENT (A) CONVERSION CURRENT (A) 180 FO = GND CS = GND SCK = NC SDO = NC SDI = GND -140 30600 2488 G14 Conversion Current vs Temperature 5.5 -80 -120 200 5.0 -60 -120 1M 4.5 VCC = 4.1V DC 0.7V VREF = 2.5V IN+ = GND IN- = GND -40 FO = GND TA = 25C -120 10k 100k 1k 100 FREQUENCY AT VCC (Hz) 4.0 VCC (V) -20 -100 10 3.5 PSRR vs Frequency at VCC -100 1 3.0 0 -100 -140 2.5 2488 G12 PSRR vs Frequency at VCC 0 VCC = 4.1V DC VREF = 2.5V IN+ = GND IN- = GND FO = GND TA = 25C -40 304 2488 G11 PSRR vs Frequency at VCC -20 306 300 0 15 30 45 60 TEMPERATURE (C) 2488 G10 0 VREF = 2.5V VIN = 0V VIN(CM) = GND FO = GND TA = 25C 302 REJECTION (dB) 0.2 310 FREQUENCY (kHz) VCC = 5V REF- = GND VIN = 0V VIN(CM) = GND TA = 25C FREQUENCY (kHz) OFFSET ERROR (ppm OF VREF) 0.3 On-Chip Oscillator Frequency vs VCC 0 15 30 45 60 TEMPERATURE (C) 75 90 2488 G17 100 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 2488 G18 2488fa 7 LTC2488 PIN FUNCTIONS FO (Pin 1): Frequency Control Pin. Digital input that controls the internal conversion clock rate. When FO is connected to ground, the converter uses its internal oscillator running at 307.2kHz. The conversion clock may also be overridden by driving the FO pin with an external clock in order to change the output rate and the digital filter rejection null. SDI (Pin 2): Serial Data Input. This pin is used to select the input channel. The serial data input is applied under control of the serial clock (SCK) during the data output/input operation. The first conversion following a new input is valid. SCK (Pin 3): Bidirectional, Digital I/O, Clock Pin. In Internal Serial Clock Operation mode, SCK is generated internally and is seen as an output on the SCK pin. In External Serial Clock Operation mode, the digital I/O clock is externally applied to the SCK pin. The Serial Clock operation mode is determined by the logic level applied to the SCK pin at power up and during the most recent falling edge of CS. (Pin 4): Active LOW Chip Select. A LOW on this pin enables C S the digital input/output and wakes up the ADC. Following each conversion, the ADC automatically enters the Sleep mode S is HIGH. and remains in this low power state as long as C S during the data output A LOW-to-HIGH transition on C aborts the data transfer and starts a new conversion. SDO (Pin 5): Three-State Digital Output. During the data output period, this pin is used as the serial data output. When the chip select pin is HIGH, the SDO pin is in a high impedance state. During the conversion and sleep periods, this pin is used as the conversion status output. When the conversion is in progress this pin is HIGH; once the conversion is complete SDO goes low. The conversion status is monitored by pulling CS LOW. GND (Pin 6): Ground. Connect this pin to a common ground plane through a low impedance connection. COM (Pin 7): The common negative input (IN-) for all single ended multiplexer configurations. The voltage on CH0 to CH3 and COM pins can have any value between GND - 0.3V to VCC + 0.3V. Within these limits, the two selected inputs (IN+ and IN-) provide a bipolar input range (VIN = IN+ - IN-) from -0.5 * VREF to 0.5 * VREF. Outside this input range, the converter produces unique over-range and under-range output codes. CH0 to CH3 (Pins 8-11): Analog Inputs. May be programmed for single-ended or differential mode. VCC (Pin 12): Positive Supply Voltage. Bypass to GND with a 10F tantalum capacitor in parallel with a 0.1F ceramic capacitor as close to the part as possible. REF+ (Pin 13), REF- (Pin 14): Differential Reference Input. The voltage on these pins can have any value between GND and VCC as long as the reference positive input, REF+, remains more positive than the negative reference input, REF-, by at least 0.1V. The differential voltage (VREF = REF+ - REF-) sets the fullscale range for all input channels. Exposed Pad (Pin 15): Ground. This pin is ground and must be soldered to the PCB ground plane. For prototyping purposes, this pin may remain floating. 2488fa 8 LTC2488 FUNCTIONAL BLOCK DIAGRAM INTERNAL OSCILLATOR VCC GND CH0 CH1 CH2 CH3 COM FO (INT/EXT) AUTOCALIBRATION AND CONTROL REF+ REF- IN+ MUX IN- - + DIFFERENTIAL 3RD ORDER MODULATOR SERIAL INTERFACE SDI SCK SDO CS DECIMATING FIR ADDRESS 2488 BD Figure 1. Functional Block Diagram TEST CIRCUITS VCC 1.69k SDO SDO 1.69k Hi-Z TO VOH VOL TO VOH VOH TO Hi-Z CLOAD = 20pF 2488 TC01 CLOAD = 20pF Hi-Z TO VOL VOH TO VOL VOL TO Hi-Z 2488 TC02 2488fa 9 LTC2488 TIMING DIAGRAMS Timing Diagram Using Internal SCK (SCK HIGH with CS) CS t1 SDO t2 Hi-Z Hi-Z tKQMIN t3 tKQMAX SCK t7 t8 SDI SLEEP DATA IN/OUT CONVERSION 2488 TD01 Timing Diagram Using External SCK (SCK LOW with CS) CS t1 SDO Hi-Z t2 Hi-Z t5 tKQMIN t4 tKQMAX SCK t7 t8 SDI SLEEP DATA IN/OUT CONVERSION 2488 TD02 2488fa 10 LTC2488 APPLICATIONS INFORMATION CONVERTER OPERATION Converter Operation Cycle The LTC2488 is a multi-channel, low power, delta-sigma, analog-to-digital converter with an easy-to-use 4-wire interface and automatic differential input current cancellation. Its operation is made up of four states (See Figure 2). The converter's operating cycle begins with the conversion, followed by the sleep state, and ends with the data input/output cycle. The 4-wire interface consists of serial data output (SDO), serial clock (SCK), chip select (CS) and serial data input (SDI).The interface, timing, operation cycle, and data output format is compatible with Linear's entire family of SPI converters. Initially, at power up, the LTC2488 performs a conversion. Once the conversion is complete, the device enters the sleep state. While in the sleep state, if CS is HIGH, power consumption is reduced by two orders of magnitude. The part remains in the sleep state as long as CS is HIGH. The conversion result is held indefinitely in a static shift register while the part is in the sleep state. Once CS is pulled LOW, the device powers up, exits the sleep state, and enters the data input/output state. If CS is brought HIGH before the first rising edge of SCK, the device returns to the sleep state and the power is reduced. If CS is brought HIGH after the first rising edge of SCK, the POWER UP IN+= CH0, IN-= CH1 data output cycle is aborted and a new conversion cycle begins. The data output corresponds to the conversion just completed. This result is shifted out on the serial data output pin (SDO) under the control of the serial clock pin (SCK). Data is updated on the falling edge of SCK allowing the user to reliably latch data on the rising edge of SCK (See Figure 3). The channel selection data for the next conversion is also loaded into the device at this time. Data is loaded from the serial data input pin (SDI) on each rising edge of SCK. The data input/output cycle concludes once 24 bits are read out of the ADC or when CS is brought HIGH. The device automatically initiates a new conversion and the cycle repeats. S and SCK pins, the LTC2488 Through timing control of the C offers several flexible modes of operation (internal or external SCK and free-running conversion modes). These various modes do not require programming and do not disturb the cyclic operation described above. These modes of operation are described in detail in the Serial Interface Timing Modes section. Ease of Use The LTC2488 data output has no latency, filter settling delay, or redundant data associated with the conversion cycle. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing multiple analog inputs is straight forward. Each conversion, immediately following a newly selected input, is valid and accurate to the full specifications of the device. The LTC2488 automatically performs offset and full scale calibration every conversion cycle independent of the input channel selected. This calibration is transparent to the user and has no effect on the operation cycle described above. The advantage of continuous calibration is extreme stability of offset and full-scale readings with respect to time, supply voltage variation, input channel, and temperature drift. CONVERT SLEEP CS = LOW AND SCK Easy Drive Input Current Cancellation CHANNEL SELECT DATA OUTPUT 2488 F02 Figure 2. LTC2488 State Transition Diagram The LTC2488 combines a high precision, delta-sigma ADC with an automatic, differential, input current cancellation front end. A proprietary front end passive sampling network transparently removes the differential input current. This 2488fa 11 LTC2488 APPLICATIONS INFORMATION enables external RC networks and high impedance sensors to directly interface to the LTC2488 without external amplifiers. The remaining common mode input current is eliminated by either balancing the differential input impedances or setting the common mode input equal to the common mode reference (see Automatic Differential Input Current Cancellation Section). This unique architecture does not require on-chip buffers, thereby enabling signals to swing beyond ground and VCC. Moreover, the cancellation does not interfere with the transparent offset and full-scale auto-calibration and the absolute accuracy (full scale + offset + linearity + drift) is maintained even with external RC networks. Power-Up Sequence The LTC2488 automatically enters an internal reset state when the power supply voltage VCC drops below approximately 2V. This feature guarantees the integrity of the conversion result, input channel selection, and serial clock mode. When VCC rises above this threshold, the converter creates an internal power-on-reset (POR) signal with a duration of approximately 4ms. The POR signal clears all internal registers. The conversion immediately following a POR cycle is performed on the input channel IN+ = CH0, IN- = CH1. The first conversion following a POR cycle is accurate within the specification of the device if the power supply voltage is restored to (2.7V to 5.5V) before the end of the POR interval. A new input channel can be programmed into the device during this first data input/output cycle. Reference Voltage Range This converter accepts a truly differential external reference voltage. The absolute/common mode voltage range for REF+ and REF- pins covers the entire operating range of the device (GND to VCC). For correct converter operation, VREF must be positive (REF+ > REF-). The LTC2488 differential reference input range is 0.1V to VCC. For the simplest operation, REF+ can be shorted to VCC and REF- can be shorted to GND. The converter output noise is determined by the thermal noise of the front end circuits. Since the transition noise is well below 1LSB (0.02LSB), a decrease in reference voltage will proportionally improve the converter resolution and improve INL. Input Voltage Range The analog inputs are truly differential with an absolute, common mode range for the CH0 to CH3 and COM input pins extending from GND - 0.3V to VCC + 0.3V. Outside these limits, the ESD protection devices begin to turn on and the errors due to input leakage current increase rapidly. Within these limits, the LTC2488 converts the bipolar differential input signal VIN = IN+ - IN- (where IN+ and IN- are the selected input channels), from -FS = -0.5 * VREF to +FS = 0.5 * VREF where VREF = REF+ - REF-. Outside this range, the converter indicates the overrange or the underrange condition using distinct output codes (see Table 1). Signals applied to the input (CH0 to CH3, COM) may extend 300mV below ground and above VCC. In order to limit any fault current, resistors of up to 5k may be added in series with the input. The effect of series resistance on the converter accuracy can be evaluated from the curves presented in the Input Current/Reference Current sections. In addition, series resistors will introduce a temperature dependent error due to input leakage current. A 1nA input leakage current will develop a 1ppm offset error on a 5k resistor if VREF = 5V. This error has a very strong temperature dependency. SERIAL INTERFACE PINS The LTC2488 transmits the conversion result, reads the input channel selection, and receives a start of conversion command through a synchronous 3- or 4-wire interface. During the conversion and sleep states, this interface can be used to access the converter status. During the data output state, it is used to read the conversion result and program the input channel. Serial Clock Input/Output (SCK) The serial clock pin (SCK) is used to synchronize the data input/output transfer. Each bit is shifted out of the SDO pin on the falling edge of SCK and data is shifted into the SDI pin on the rising edge of SCK. 2488fa 12 LTC2488 APPLICATIONS INFORMATION The serial clock pin (SCK) can be configured as either a master (SCK is an output generated internally) or a slave (SCK is an input and applied externally). Master mode (Internal SCK) is selected by simply floating the SCK pin. Slave mode (External SCK) is selected by driving SCK low during power up and each falling edge of CS. Specific details of these SCK modes are described in the Serial Interface Timing Modes section. Serial Data Output (SDO) The serial data output pin (SDO) provides the result of the last conversion as a serial bit stream (MSB first) during the data output state. In addition, the SDO pin is used as an end of conversion indicator during the conversion and sleep states. When CS is HIGH, the SDO driver is switched to a high impedance state in order to share the data output line with other devices. If CS is brought LOW during the conversion phase, the EOC bit (SDO pin) will be driven HIGH. Once the conversion is complete, if CS is brought LOW, EOC will be driven LOW indicating the conversion is complete and the result is ready to be shifted out of the device. Chip Select (CS) The active low CS pin is used to test the conversion status, enable I/O data transfer, initiate a new conversion, control the duration of the sleep state, and set the SCK mode. At the conclusion of a conversion cycle, while CS is HIGH, the device remains in a low power sleep state where the supply current is reduced several orders of magnitude. In order to exit the sleep state and enter the data output state, CS must be pulled low. Data is now shifted out the SDO pin under control of the SCK pin as described previously. A new conversion cycle is initiated either at the conclusion of the data output cycle (all 24 data bits read) or by pulling CS HIGH any time between the first and 24th rising edges of the serial clock (SCK). In this case, the data output is aborted and a new conversion begins. Serial Data Input (SDI) The serial data input (SDI) is used to select the input channel. Data is shifted into the device during the data output/input state on the rising edge of SCK while CS is low. OUTPUT DATA FORMAT The LTC2488 serial output stream is 24 bits long. The first bit indicates the conversion status, the second bit is always zero, and the third bit conveys sign information. The next 17 bits are the conversion result, MSB first. The remaining 4 bits are always LOW. Bit 23 (first output bit) is the end of conversion (EOC) indicator. This bit is available on the SDO pin during the conversion and sleep states whenever CS is LOW. This bit is HIGH during the conversion cycle, goes LOW once the conversion is complete, and is HIGH-Z when CS is HIGH. Bit 22 (second output bit) is a dummy bit (DMY) and is always LOW. Bit 21 (third output bit) is the conversion result sign indicator (SIG). If the selected input (VIN = IN+ - IN-) is greater than or equal to 0V, this bit is HIGH. If VIN < 0, this bit is LOW. Bit 20 (fourth output bit) is the most significant bit (MSB) of the result. This bit in conjunction with Bit 21 also provides underrange and overrange indication. If both Bit 21 and Bit 20 are HIGH, the differential input voltage is above +FS. If both Bit 21 and Bit 20 are LOW, the differential input voltage is below -FS. The function of these bits is summarized in Table 1. Table 1. LTC2488 Status Bits Input Range Bit 23 EOC Bit 22 DMY Bit 21 SIG Bit 20 MSB VIN 0.5 * VREF 0 0 1 1 0V VIN < 0.5 * VREF 0 0 1 0 -0.5 * VREF VIN < 0V 0 0 0 1 VIN < -0.5 * VREF 0 0 0 0 Bits 20 to 4 are the 16-bit plus sign conversion result MSB first. Bit 4 is the least significant bit (LSB16). Bits 3 to 0 are always LOW. 2488fa 13 LTC2488 APPLICATIONS INFORMATION This bit serves as EOC (Bit 23) for the next conversion cycle. Table 2 summarizes the output data format. Data is shifted out of the SDO pin under control of the serial clock (SCK) (see Figure 3). Whenever CS is HIGH, SDO remains high impedance and SCK is ignored. As long as the voltage on the IN+ and IN- pins remains between -0.3V and VCC + 0.3V (absolute maximum operating range) a conversion result is generated for any differential input voltage VIN from -FS = -0.5 * VREF to +FS = 0.5 * VREF. For differential input voltages greater than +FS, the conversion result is clamped to the value corresponding to +FS + 1LSB. For differential input voltages below -FS, the conversion result is clamped to the value -FS - 1LSB. In order to shift the conversion result out of the device, CS must first be driven LOW. EOC is seen at the SDO pin of the device once CS is pulled LOW. EOC changes in real time as a function of the internal oscillator or the clock applied to the fO pin from HIGH to LOW at the completion of a conversion. This signal may be used as an interrupt for an external microcontroller. Bit 23 (EOC) can be captured on the first rising edge of SCK. Bit 22 is shifted out of the device on the first falling edge of SCK. The final data bit (Bit 0) is shifted out on the on the falling edge of the 23rd SCK and may be latched on the rising edge of the 24th SCK pulse. On the falling edge of the 24th SCK pulse, SDO goes HIGH indicating the initiation of a new conversion cycle. INPUT DATA FORMAT The LTC2488 serial input word is 8 bits long. The input bits (SGL, ODD, A2, A1, A0) are used to select the input channel. CS 1 2 3 4 5 1 0 EN SGL ODD EOC "0" SIG MSB 6 7 8 A2 A1 A0 9 10 11 12 13 14 24 SCK (EXTERNAL) DON'T CARE SDI SDO DON'T CARE BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 CONVERSION BIT 9 BIT 0 DATA INPUT/OUTPUT SLEEP 2488 F03 Figure 3. Channel Selection and Data Output Timing Table 2. Output Data Format Differential Input Voltage VIN* Bit 23 EOC Bit 22 DMY Bit 21 SIG Bit 20 MSB Bit 19 Bit 18 Bit 17 ... Bit 4 LSB Bits 3 to 0 Always 0 VIN* 0.5 * VREF** 0 0 1 1 0 0 0 ... 0 0000 0.5 * VREF** - 1LSB 0 0 1 0 1 1 1 ... 1 0000 0.25 * VREF** 0 0 1 0 1 0 0 ... 0 0000 0.25 * VREF** - 1LSB 0 0 1 0 0 1 1 ... 1 0000 0 0 0 1 0 0 0 0 ... 0 0000 -1LSB 0 0 0 1 1 1 1 ... 1 0000 -0.25 * VREF** 0 0 0 1 1 0 0 ... 0 0000 -0.25 * VREF** - 1LSB 0 0 0 1 0 1 1 ... 1 0000 -0.5 * VREF** 0 0 0 1 0 0 0 ... 0 0000 VIN* < -0.5 * VREF** 0 0 0 0 1 1 1 ... 1 0000 *The differential input voltage VIN = IN+ - IN-. **The differential reference voltage VREF = REF+ - REF-. 2488fa 14 LTC2488 APPLICATIONS INFORMATION After power up, the device initiates an internal reset cycle which sets the input channel to CH0 to CH1 (IN+ = CH0, IN- = CH1). The first conversion automatically begins at power up using this default input channel. Once the conversion is complete, a new word may be written into the device. The first three bits of the input word consist of two preamble bits and one enable bit. These three bits are used to enable the input channel selection. Valid settings for these three bits are 000, 100, and 101. Other combinations should be avoided. If the first three bits are 000 or 100, the following data is ignored (don't care) and the previously selected input channel remains valid for the next conversion. If the first three bits shifted into the device are 101, then the next five bits select the input channel for the next conversion cycle (see Table 3). The first input bit (SGL) following the 101 sequence determines if the input selection is differential (SGL = 0) or single-ended (SGL = 1). For SGL = 0, two adjacent channels can be selected to form a differential input. For SGL = 1, one of four channels is selected as the positive input. The negative input is COM for all single ended operations. The remaining four bits (ODD, A2, A1, A0) determine which channel(s) is/are selected and the polarity (for a differential input). SERIAL INTERFACE TIMING MODES The LTC2488's 4-wire interface is SPI and MICROWIRE compatible. This interface offers several flexible modes of operation. These include internal/external serial clock, 3- or 4-wire I/O, single cycle or continuous conversion. The following sections describe each of these timing modes in detail. In all cases, the converter can use the internal oscillator (FO = LOW) or an external oscillator connected to the FO pin. For each mode, the operating cycle, data input format, data output format, and performance remain the same. Refer to Table 4 for a summary. Table 3 Channel Selection MUX ADDRESS SGL ODD/ SIGN A2 A1 CHANNEL SELECTION A0 0 1 IN+ IN- *0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 0 0 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 1 1 0 0 IN- 2 3 IN+ IN- IN- IN+ COM IN+ IN+ IN- IN+ IN- IN+ IN- IN+ 1 IN- *Default at power up Table 4. Serial Interface Timing Modes CONFIGURATION External SCK, Single Cycle Conversion SCK CONVERSION DATA OUTPUT CONNECTION AND SOURCE CYCLE CONTROL CONTROL WAVEFORMS S and SCK CS and SCK C Figures 4, 5 External External SCK, 3-Wire I/O External SCK SCK Figure 6 Internal SCK, Single Cycle Conversion Internal CS CS Figures 7, 8 Internal SCK, 3-Wire I/O, Continuous Conversion Internal Continuous Internal Figure 9 2488fa 15 LTC2488 APPLICATIONS INFORMATION External Serial Clock, Single Cycle Operation When the device is in the sleep state, its conversion result is held in an internal static shift register. The device remains in the sleep state until the first rising edge of SCK is seen while CS is LOW. The input data is then shifted in via the SDI pin on each rising edge of SCK (including the first rising edge). The channel selection will be used for the following conversion cycle. If the input channel is changed during this I/O cycle, the new settings take effect on the conversion cycle following the data input/output cycle. The output data is shifted out the SDO pin on each falling edge of SCK. This enables external circuitry to latch the output on the rising edge of SCK. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 24th rising edge of SCK. On the 24th falling edge of SCK, the device begins a new conversion and SDO goes HIGH (EOC = 1) indicating a conversion is in progress. This timing mode uses an external serial clock to shift out the conversion result and CS to monitor and control the state of the conversion cycle (see Figure 4). The external serial clock mode is selected during the powerup sequence and on each falling edge of CS. In order to enter and remain in the external SCK mode of operation, SCK must be driven LOW both at power up and on each CS falling edge. If SCK is HIGH on the falling edge of CS, the device will switch to the internal SCK mode. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. While CS is LOW, EOC is output to the SDO pin. EOC = 1 while a conversion is in progress and EOC = 0 if the conversion is complete and the device is in the sleep state. Independent of CS, the device automatically enters the sleep state once the conversion is complete; however, in order to reduce the power, CS must be HIGH. At the conclusion of the data cycle, CS may remain LOW and EOC monitored as an end-of-conversion interrupt. Typically, CS remains LOW during the data output/input 2.7V TO 5.5V 12 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F REFERENCE VOLTAGE 0.1V TO VCC 0.1F 13 14 8 9 10 ANALOG INPUTS 11 7 REF+ 2 SDI REF- 3 SCK 4-WIRE SPI INTERFACE CH0 CH1 CS CH2 SDO 4 5 CH3 COM GND 6 CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB 9 19 20 21 22 23 24 SCK (EXTERNAL) SDI DON'T CARE SDO SLEEP Hi-Z LSB BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 CONVERSION DON'T CARE DATA INPUT/OUTPUT BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 CONVERSION 2488 F04 Figure 4. External Serial Clock, Single Cycle Operation 2488fa 16 LTC2488 APPLICATIONS INFORMATION state. However, the data output state may be aborted by pulling CS HIGH any time between the 1st falling edge and the 24th falling edge of SCK (see Figure 5). On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. In order to program a new input channel, 8 SCK clock pulses are required. If the data output sequence is aborted prior to the 8th falling edge of SCK, the new input data is ignored and the previously selected input channel remains valid. If the rising edge of CS occurs after the 8th falling edge of SCK, the new input channel is loaded and valid for the next conversion cycle. the power-on reset (POR) cycle. The POR cycle typically concludes 4ms after VCC exceeds 2V. The level applied to SCK at this time determines if SCK is internally generated or externally applied. In order to enter the external SCK mode, SCK must be driven LOW prior to the end of the POR cycle. Since CS is tied LOW, the end-of-conversion (EOC) can be continuously monitored at the SDO pin during the convert and sleep states. EOC may be used as an interrupt to an external controller. EOC = 1 while the conversion is in progress and EOC = 0 once the conversion is complete. On the falling edge of EOC, the conversion result is loading into an internal static shift register. The output data can now be shifted out the SDO pin under control of the externally applied SCK signal. Data is updated on the falling edge of SCK. The input data is shifted into the device through the SDI pin on the rising edge of SCK. On the 24th falling edge of SCK, SDO goes HIGH, indicating a new conversion has begun. This data now serves as EOC for the next conversion. External Serial Clock, 3-Wire I/O This timing mode uses a 3-wire serial I/O interface. The conversion result is shifted out of the device by an externally generated serial clock (SCK) signal (see Figure 6). CS is permanently tied to ground, simplifying the user interface or isolation barrier. The external serial clock mode is selected at the end of 2.7V TO 5.5V 12 = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F 0.1F VCC REFERENCE VOLTAGE 0.1V TO VCC 13 REF+ 14 REF- 8 9 ANALOG INPUTS 10 11 7 2 SDI 3 SCK 4-WIRE SPI INTERFACE CH0 CH1 CS CH2 SDO 4 5 CH3 COM GND 6 CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB SCK (EXTERNAL) SDI DON'T CARE SDO Hi-Z BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 CONVERSION SLEEP DON'T CARE DATA INPUT/OUTPUT BIT 15 CONVERSION SLEEP 2488 F05 Figure 5. External Serial Clock, Reduced Output Data Length and Valid Channel Selection 2488fa 17 LTC2488 APPLICATIONS INFORMATION 2.7V TO 5.5V 12 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F REFERENCE VOLTAGE 0.1V TO VCC 0.1F 13 REF+ 14 - 8 9 ANALOG INPUTS 10 11 7 REF 2 SDI 3 SCK 3-WIRE SPI INTERFACE CH0 CH1 SDO CH2 CS 5 4 CH3 COM GND 6 CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB 9 19 20 21 22 23 24 BIT 2 BIT 1 BIT 0 SCK (EXTERNAL) SDI DON'T CARE SDO LSB BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 CONVERSION DON'T CARE BIT 4 DATA INPUT/OUTPUT SLEEP BIT 3 CONVERSION 2488 F06 Figure 6. External Serial Clock, 3-Wire Operation (CS = 0) Internal Serial Clock, Single Cycle Operation This timing mode uses the internal serial clock to shift out the conversion result and CS to monitor and control the state of the conversion cycle (see Figure 7). In order to select the internal serial clock timing mode, the serial clock pin (SCK) must be floating or pulled HIGH before the conclusion of the POR cycle and prior to each S . An internal weak pull-up resistor is active falling edge of C on the SCK pin during the falling edge of CS; therefore, the internal SCK mode is automatically selected if SCK is not externally driven. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled low in order to monitor the state of the converter. Once CS is pulled LOW, SCK goes LOW and EOC is output to the SDO pin. EOC = 1 while the conversion is in progress and EOC = 0 if the device is in the sleep state. C , if the conversion is complete (E O C = When testing E O 0), the device will exit sleep state. In order to return to the S must be sleep state and reduce the power consumption, C pulled HIGH before the device pulls SCK HIGH. When the device is using its own internal oscillator (FO is tied LOW), the first rising edge of SCK occurs 12s (tEOCTEST = 12s) S . If FO is driven by an external after the falling edge of C oscillator of frequency fEOSC, then tEOCTEST = 3.6/fEOSC. If CS remains LOW longer than tEOCTEST, the first rising edge of SCK will occur and the conversion result is shifted out the SDO pin on the falling edge of SCK. The serial input word (SDI) is shifted into the device on the rising edge of SCK. After the 24th rising edge of SCK a new conversion automatically begins. SDO goes HIGH (EOC = 1) and SCK remains HIGH for the duration of the conversion cycle. Once the conversion is complete, the cycle repeats. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH any time between the 1st rising edge and the 24th falling edge of SCK (see Figure 8). On the rising edge of CS, the device aborts the data output state and immediately initiates a new conversion. In order to program a new input channel, 8 SCK clock pulses are required. If the data output sequence is aborted prior to 2488fa 18 LTC2488 APPLICATIONS INFORMATION 2.7V TO 5.5V 12 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F REFERENCE VOLTAGE 0.1V TO VCC 0.1F 13 14 8 9 10 ANALOG INPUTS 11 7 + REF VCC 2 SDI REF- OPTIONAL 10k 3 SCK 4-WIRE SPI INTERFACE CH0 CH1 CS CH2 SDO 4 5 CH3 COM GND 6 <tEOCTEST CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB 9 19 20 21 22 23 24 SCK (INTERNAL) SDI DON'T CARE SDO SLEEP Hi-Z LSB BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 CONVERSION DON'T CARE DATA INPUT/OUTPUT BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 CONVERSION 2488 F07 Figure 7. Internal Serial Clock, Single Cycle Operation the 8th falling edge of SCK, the new input data is ignored and the previously selected input channel remains valid. If the rising edge of CS occurs after the 8th falling edge of SCK, the new input channel is loaded and valid for the next conversion cycle. Internal Serial Clock, 3-Wire I/O, Continuous Conversion. This timing mode uses a 3-wire interface. The conversion result is shifted out of the device by an internally generated serial clock (SCK) signal (see Figure 9). In this case, CS is permanently tied to ground, simplifying the user interface or transmission over an isolation barrier. The internal serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded approximately 4ms after VCC exceeds 2V. An internal weak pull-up is active during the POR cycle; therefore, the internal serial clock timing mode is automatically selected if SCK is floating or driven HIGH. During the conversion, the SCK and the serial data output pin (SDO) are HIGH (EOC = 1). Once the conversion is complete, SCK and SDO go LOW (EOC = 0) indicating the conversion has finished and the device has entered the sleep state. The device remains in the sleep state a minimum amount of time (1/2 the internal SCK period) then immediately begins outputting and inputting data. The input data is shifted through the SDI pin on the rising edge of SCK (including the first rising edge) and the output data is shifted out the SDO pin on the falling edge of SCK. The data input/output cycle is concluded and a new conversion automatically begins after the 24th rising edge of SCK. During the next conversion, SCK and SDO remain HIGH until the conversion is complete. The Use of a 10k Pull-Up on SCK for Internal SCK Selection If CS is pulled HIGH while the converter is driving SCK LOW, the internal pull-up is not available to restore SCK to a logic HIGH state if SCK is floating. This will cause the device to exit the internal SCK mode on the next falling edge of CS. This can be avoided by adding an external 10k pull-up resistor to the SCK pin. 2488fa 19 LTC2488 APPLICATIONS INFORMATION 2.7V TO 5.5V 12 VCC = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F REFERENCE VOLTAGE 0.1V TO VCC 0.1F REF+ SDI 14 REF- SCK 8 9 10 ANALOG INPUTS VCC 13 11 7 2 OPTIONAL 10k 3 4-WIRE SPI INTERFACE CH0 CH1 CS CH2 SDO 4 5 CH3 COM GND 6 <tEOCTEST CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB 9 10 SCK (INTERNAL) SDI DON'T CARE SDO DON'T CARE Hi-Z BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 BIT 14 BIT 13 CONVERSION SLEEP DATA INPUT/OUTPUT CONVERSION 2488 F08 Figure 8. Internal Serial Clock, Reduced Data Output Length with Valid Channel and Configuration Selection 2.7V TO 5.5V 12 = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2488 10F 0.1F VCC REFERENCE VOLTAGE 0.1V TO VCC REF+ SDI 14 REF- SCK 8 9 ANALOG INPUTS VCC 13 10 11 7 2 OPTIONAL 10k 3 3-WIRE SPI INTERFACE CH0 CH1 SDO CH2 CS 5 4 CH3 COM GND 6 CS 1 2 3 4 5 6 7 8 1 0 EN SGL ODD A2 A1 A0 EOC "0" SIG MSB 9 19 20 21 22 23 24 BIT 1 BIT 0 SCK (INTERNAL) SDI DON'T CARE SDO LSB BIT 23 BIT 22 BIT 21 BIT 20 BIT 19 BIT 18 BIT 17 BIT 16 BIT 15 CONVERSION DON'T CARE BIT 4 DATA INPUT/OUTPUT BIT 3 BIT 2 CONVERSION 2488 F09 Figure 9. Internal Serial Clock, Continuous Operation 2488fa 20 LTC2488 APPLICATIONS INFORMATION Whenever SCK is LOW, the LTC2488's internal pull-up at SCK is disabled. Normally, SCK is not externally driven if the device is operating in the internal SCK timing mode. However, certain applications may require an external driver on SCK. If the driver goes Hi-Z after outputting a LOW signal, the internal pull-up is disabled. An external 10k pull-up resistor prevents the device from exiting the internal SCK mode under this condition. external control signal is less than twice the propagation delay from the driver to the input pin. For reference, on a regular FR-4 board, the propagation delay is approximately 183ps/inch. In order to prevent overshoot, a driver with a 1ns transition time must be connected to the converter through a trace shorter than 2.5 inches. This becomes difficult when shared control lines are used and multiple reflections occur. A similar situation may occur during the sleep state when CS is pulsed HIGH-LOW-HIGH in order to test the conversion status. If the device is in the sleep state (EOC = 0), SCK will go LOW. If CS goes HIGH before the time tEOCtest, the internal pull-up is activated. If SCK is heavily loaded, the internal pull-up may not restore SCK to a HIGH state before the next falling edge of CS. The external 10k pull-up resistor prevents the device from exiting the internal SCK mode under this condition. Parallel termination near the input pin of the LTC2488 will eliminate this problem, but will increase the driver power dissipation. A series resistor from 27 to 54 (depending on the trace impedance and connection) placed near the driver will also eliminate over/under shoot without additional driver power dissipation. PRESERVING THE CONVERTER ACCURACY The LTC2488 is designed to reduce as much as possible sensitivity to device decoupling, PCB layout, anti-aliasing circuits, line frequency perturbations, and temperature sensitivity. In order to achieve maximum performance a few simple precautions should be observed. Digital Signal Levels The LTC2488's digital interface is easy to use. Its digital inputs SDI, FO, CS, and SCK (in external serial clock mode) accept standard CMOS logic levels. Internal hysteresis circuits can tolerate edge transition times as slow as 100s. The digital input signal range is 0.5V to VCC - 0.5V. During transitions, the CMOS input circuits draw dynamic current. For optimal performance, application of signals to the serial data interface should be reserved for the sleep and data output periods. During the conversion period, overshoot and undershoot of fast digital signals applied to both the serial digital interface and the external oscillator pin (FO) may degrade the converter performance. Undershoot and overshoot occur due to impedance mismatch of the circuit board trace at the converter pin when the transition time of an For many applications, the serial interface pins (SCK, SDI, CS, FO) remain static during the conversion cycle and no degradation occurs. On the other hand, if an external oscillator is used (FO driven externally) it is active during the conversion cycle. Moreover, the digital filter rejection is minimal at the clock rate applied to FO. Care must be taken to ensure external inputs and reference lines do not cross this signal or run near it. These issues are avoided when using the internal oscillator. Driving the Input and Reference The input and reference pins of the LTC2488 are connected directly to a switched capacitor network. Depending on the relationship between the differential input voltage and the differential reference voltage, these capacitors are switched between these four pins. Each time a capacitor is switched between two of these pins, a small amount of charge is transferred. A simplified equivalent circuit is shown in Figure 10. When using the LTC2488's internal oscillator, the input capacitor array is switched at 123kHz. The effect of the charge transfer depends on the circuitry driving the input/reference pins. If the total external RC time constant is less than 580ns the errors introduced by the sampling process are negligible since complete settling occurs. Typically, the reference inputs are driven from a low impedance source. In this case, complete settling occurs even with large external bypass capacitors. The inputs (CH0 to 2488fa 21 LTC2488 APPLICATIONS INFORMATION IIN+ IN+ INPUT MULTIPLEXER 100 INTERNAL SWITCH NETWORK ( ) I IN+ 10k ( ) ( ) = I IN- I REF + AVG AVG = VIN(CM) VREF(CM) 0.5*REQ ( 1.5VREF + VREF(CM) - VIN(CM) 0.5 *REQ )- 2 VIN VREF *REQ where: IIN- IN- AVG 100 VREF =REF + REF REF + -REF VREF(CM) = 2 10k IREF+ REF+ CEQ 12pF 10k VIN =IN+ IN ,WHERE IN+ AND IN ARE THE SELECTED INPUT CHANNELS IN+ -IN VIN(CM) = 2 REQ = 2.98M INTERNAL OSCILLATOR ( ) REQ = 0.833*1012 /fEOSC EXTERNAL OSCILLATOR IREF- REF- 10k 2488 F10 SWITCHING FREQUENCY fSW = 123kHz INTERNAL OSCILLATOR fSW = 0.4 * fEOSC EXTERNAL OSCILLATOR Figure 10. LTC2488 Equivalent Analog Input Circuit CH3, COM), on the other hand, are typically driven from larger source resistances. Source resistances up to 10k may interface directly to the LTC2488 and settle completely; however, the addition of external capacitors at the input terminals in order to filter unwanted noise (anti-aliasing) results in incomplete settling. Automatic Differential Input Current Cancellation In applications where the sensor output impedance is low (up to 10k with no external bypass capacitor or up to 500 with 0.001F bypass), complete settling of the input occurs. In this case, no errors are introduced and direct digitization is possible. For many applications, the sensor output impedance combined with external input bypass capacitors produces RC time constants much greater than the 580ns required for 1ppm accuracy. For example, a 10k bridge driving a 0.1F capacitor has a time constant an order of magnitude greater than the required maximum. The LTC2488 uses a proprietary switching algorithm that forces the average differential input current to zero independent of external settling errors. This allows direct digitization of high impedance sensors without the need of buffers. The switching algorithm forces the average input current on the positive input (IIN+) to be equal to the average input current on the negative input (IIN-). Over the complete conversion cycle, the average differential input current (IIN+ - IIN-) is zero. While the differential input current is zero, the common mode input current (IIN+ + IIN-)/2 is proportional to the difference between the common mode input voltage (VIN(CM)) and the common mode reference voltage (VREF(CM)). In applications where the input common mode voltage is equal to the reference common mode voltage, as in the case of a balanced bridge, both the differential and common mode input currents are zero. The accuracy of the converter is not compromised by settling errors. In applications where the input common mode voltage is constant but different from the reference common mode voltage, the differential input current remains zero while the common mode input current is proportional to the difference between VIN(CM) and VREF(CM). For a reference common mode voltage of 2.5V and an input common mode of 1.5V, the common mode input current is approximately 0.74A. This common mode input current does not degrade the accuracy if the source impedances tied to IN+ and 2488fa 22 LTC2488 APPLICATIONS INFORMATION In addition to the input sampling current, the input ESD protection diodes have a temperature dependent leakage current. This current, nominally 1nA (10nA Max), results in a small offset shift. A 1k source resistance will create a 1V typical and a 10V maximum offset voltage. Reference Current Similar to the analog inputs, the LTC2488 samples the differential reference pins (REF+ and REF-) transferring small amounts of charge to and from these pins, thus producing a dynamic reference current. If incomplete settling occurs (as a function the reference source resistance and reference bypass capacitance) linearity and gain errors are introduced. VCC = 5V VREF = 5V VIN+ = 3.75V VIN- = 1.25V FO = GND TA = 25C 80 70 +FS ERROR (ppm) In applications where the common mode input voltage varies as a function of the input signal level (single ended type sensors), the common mode input current varies proportionally with input voltage. For the case of balanced input impedances, the common mode input current effects are rejected by the large CMRR of the LTC2488, leading to little degradation in accuracy. Mismatches in source impedances lead to gain errors proportional to the difference between the common mode input and common mode reference. 1% mismatches in 1k source resistances lead to gain errors on the order of 15ppm. Based on the stability of the internal sampling capacitors and the accuracy of the internal oscillator, a one-time calibration will remove this error. 90 60 50 CREF = 0.01F CREF = 0.001F CREF = 100pF CREF = 0pF 40 30 20 10 0 -10 0 10 1k 100 RSOURCE () 10k 100k 2488 F11 Figure 11. +FS Error vs RSOURCE at VREF (Small CREF) 10 0 -10 -FS ERROR (ppm) IN- are matched. Mismatches in source impedance lead to a fixed offset error but do not effect the linearity or full scale reading. A 1% mismatch in a 1k source resistance leads to a 74V shift in offset voltage. -20 -30 CREF = 0.01F CREF = 0.001F CREF = 100pF CREF = 0pF -40 -50 VCC = 5V -60 VREF = 5V V + = 1.25V -70 VIN- = 3.75V IN -80 FO = GND TA = 25C -90 10 0 1k 100 RSOURCE () 10k 100k 2488 F12 Figure 12. -FS Error vs RSOURCE at VREF (Small CREF) For relatively small values of external reference capacitance (CREF < 1nF), the voltage on the sampling capacitor settles for reference impedances of many k (if CREF = 100pF up to 10k will not degrade the performance) (see Figures 11 and 12). ing with the internal oscillator) (see Figures 13 and 14). If the input common mode voltage is equal to the reference common mode voltage, a linearity error of approximately 0.67ppm per 100 of reference resistance results (see Figure 15). In applications where the input and reference common mode voltages are different, the errors increase. A 1V difference in between common mode input and common mode reference results in a 6.7ppm INL error for every 100 of reference resistance. In cases where large bypass capacitors are required on the reference inputs (CREF > 0.01F) full-scale and linearity errors are proportional to the value of the reference resistance. Every ohm of reference resistance produces a full-scale error of approximately 0.5ppm (while operat- In addition to the reference sampling charge, the reference ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally 1nA (10nA max) results in a small gain error. A 100 reference resistance will create a 0.5V full scale error. 2488fa 23 LTC2488 APPLICATIONS INFORMATION 500 VCC = 5V VREF = 5V VIN+ = 3.75V VIN- = 1.25V FO = GND TA = 25C +FS ERROR (ppm) 400 300 Normal Mode Rejection and Anti-aliasing CREF = 1F, 10F CREF = 0.1F 200 CREF = 0.01F 100 0 200 0 600 400 RSOURCE () 800 1000 2488 F13 Figure 13. +FS Error vs RSOURCE at VREF (Large CREF) 0 -100 -FS ERROR (ppm) CREF = 0.01F -200 CREF = 1F, 10F -300 VCC = 5V VREF = 5V VIN+ = 1.25V VIN- = 3.75V FO = GND TA = 25C -400 -500 0 200 CREF = 0.1F 600 400 RSOURCE () 800 1000 One of the advantages delta-sigma ADCs offer over conventional ADCs is on-chip digital filtering. Combined with a large oversample ratio, the LTC2488 significantly simplifies anti-aliasing filter requirements. Additionally, the input current cancellation feature allows external low pass filtering without degrading the DC performance of the device. The SINC4 digital filter provides excellent normal mode rejection at all frequencies except DC and integer multiples of the modulator sampling frequency (fS). The modulator sampling frequency is fS = 15,360Hz while operating with its internal oscillator and fS = FEOSC/20 when operating with an external oscillator of frequency FEOSC. When using the internal oscillator, the LTC2488 is designed to reject line frequencies. As shown in Figure 16, rejection nulls occur at multiples of frequency fN, where fN = 55Hz for simultaneous 50Hz/60Hz rejection. Multiples of the modulator sampling rate (fS = fN * 256) only reject noise to 15dB (see Figure 17), if noise sources are present at these frequencies anti-aliasing will reduce their effects. The user can expect to achieve this level of performance using the internal oscillator, as shown in Figure 18. Measured values of normal mode rejection are shown superimposed over the theoretical values. 2488 F14 Figure 14. -FS Error vs RSOURCE at VREF (Large CREF) Traditional high order delta-sigma modulators suffer from potential instabilities at large input signal levels. The 0 VCC = 5V 8 VREF = 5V VIN(CM) = 2.5V 6 T = 25C A 4 CREF = 10F INPUT NORMAL MODE REJECTION (dB) INL (ppm OF VREF) 10 R = 1k 2 R = 500 0 R = 100 -2 -4 -6 -8 -10 -0.5 -0.3 0.1 -0.1 VIN/VREF 0.3 0.5 2488 F15 Figure 15. INL vs Differential Input Voltage and Reference Source Resistance for CREF > 1F fN = fEOSC/5120 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 0 fN 2fN 3fN 4fN 5fN 6fN 7fN INPUT SIGNAL FREQUENCY (Hz) 8fN 2488 F16 Figure 16. Input Normal Mode Rejection at DC 2488fa 24 LTC2488 APPLICATIONS INFORMATION proprietary architecture used for the LTC2488 third order modulator resolves this problem and guarantees stability with input signals 150% of full-scale. In many industrial applications, it is not uncommon to have microvolt level signals superimposed over unwanted error sources with several volts of peak-to-peak noise. Figure 19 shows measurement results for the rejection of a 7.5V peak-to-peak noise source (150% of full scale) applied to the LTC2488. From this curve, it is shown that the rejection performance is maintained even in extremely noisy environments. INPUT NORMAL MODE REJECTION (dB) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 250fN 252fN 254fN 256fN 258fN 260fN 262fN INPUT SIGNAL FREQUENCY (Hz) Output Data Rate 2488 F17 Figure 17. Input Normal Mode Rejection at fS = 256 * fN NORMAL MODE REJECTION (dB) 0 VIN(P-P) = 5V VIN(P-P) = 7.5V (150% OF FULL SCALE) -20 VCC = 5V VREF = 5V VIN(CM) = 2.5V TA = 25C -40 -60 -80 -100 -120 0 12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200 INPUT FREQUENCY (Hz) 2488 F18 Figure 18. Input Normal Mode Rejection vs Input Frequency with Input Perturbation of 100% (50Hz/60Hz Notch) NORMAL MODE REJECTION (dB) 0 MEASURED DATA CALCULATED DATA -20 -40 VCC = 5V VREF = 5V VIN(CM) = 2.5V VIN(P-P) = 5V TA = 25C -60 -80 -100 -120 0 12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200 INPUT FREQUENCY (Hz) 2488 F19 Figure 19. Measure Input Normal Mode Rejection vs Input Frequency with Input Perturbation of 150% (60Hz Notch) When using its internal oscillator, the LTC2488 produces up to 6.9 samples per second (sps) with a notch frequency of 55Hz. The actual output data rate depends upon the length of the sleep and data output cycles which are controlled by the user and can be made insignificantly short. When operating with an external conversion clock (FO connected to an external oscillator), the LTC2488 output data rate can be increased. The duration of the conversion cycle is 41036/fEOSC. If fEOSC = 307.2kHz, the converter behaves as if the internal oscillator is used. An increase in fEOSC over the nominal 307.2kHz will translate into a proportional increase in the maximum output data rate (up to a maximum of 100sps). The increase in output rate leads to degradation in offset, full-scale error, and effective resolution as well as a shift in frequency rejection. A change in fEOSC results in a proportional change in the internal notch position. This leads to reduced differential mode rejection of line frequencies. The common mode rejection of line frequencies remains unchanged, thus fully differential input signals with a high degree of symmetry on both the IN+ and IN- pins will continue to reject line frequency noise. An increase in fEOSC also increases the effective dynamic input and reference current. External RC networks will continue to have zero differential input current, but the time required for complete settling (580ns for fEOSC = 307.2kHz) is reduced, proportionally. Once the external oscillator frequency is increased above 1MHz (a more than 3x increase in output rate) the effective2488fa 25 LTC2488 APPLICATIONS INFORMATION ness of internal auto calibration circuits begins to degrade. This results in larger offset errors, full scale errors, and decreased resolution (see Figures 20 to 27). Easy Drive ADCs Simplify Measurement of High Impedance Sensors Delta-Sigma ADCs, with their high accuracy and high noise immunity, are ideal for directly measuring many types of sensors. Nevertheless, input sampling currents can overwhelm high source impedances or low-bandwidth, micropower signal conditioning circuits. The LTC2488 solves this problem by balancing the input currents, thus simplifying or eliminating the need for signal conditioning circuits. A common application for a delta-sigma ADC is thermistor measurement. Figure 28 shows two examples of thermistor digitization benefiting from the Easy Drive technology. The first circuit (applied to input channels CH0 and CH1) uses balanced reference resistors in order to balance the common mode input/reference voltage and balance the differential input source resistance. If reference resistors R1 and R4 are exactly equal, the input current is zero and no errors result. If these resistors have a 1% tolerance, the maximum error in measured resistance is 1.6 due to a shift in common mode voltage; far less than the 1% error of the reference resistors themselves. No amplifier is required, making this an ideal solution in micropower applications. Easy Drive also enables very low power, low bandwidth amplifiers to drive the input to the LTC2488. As shown in Figure 28, CH2 is driven by the LT1494. The LT1494 has excellent DC specs for an amplifier with 1.5A supply current (the maximum offset voltage is 150V and the open loop gain is 100,000). Its 2kHz bandwidth makes it unsuitable for driving conventional delta sigma ADCs. Adding a 1k, 0.1F filter solves this problem by providing a charge reservoir that supplies the LTC2488 instantaneous current, while the 1k resistor isolates the capacitive load from the LT1494. Conventional delta sigma ADCs input sampling current lead to DC errors as a result of incomplete settling in the external RC network. The Easy Drive technology cancels the differential input current. By balancing the negative input (CH3) with a 1k, 0.1F network errors due to the common mode input current are cancelled. 2488fa 26 LTC2488 APPLICATIONS INFORMATION 30 3000 TA = 85C 20 10 2500 2000 TA = 25C -3000 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 18 18 16 16 12 10 VIN(CM) = VREF(CM) VCC = VREF = 5V VIN = 0V FO = EXT CLOCK RES = LOG 2 (VREF/NOISERMS) 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) TA = 25C TA = 85C 14 12 VIN(CM) = VREF(CM) VCC = VREF = 5V FO = EXT CLOCK RES = LOG 2 (VREF/INLMAX) 10 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) VIN(CM) = VREF(CM) VIN = 0V 15 FO = EXT CLOCK TA = 25C 10 VCC = VREF = 5V 5 0 -5 -10 VCC = 5V, VREF = 2.5V 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 2488 F24 Figure 24. Resolution (INLMAX 1LSB) vs Output Data Rate and Temperature 18 2488 F25 Figure 25. Offset Error vs Output Data Rate and Reference Voltage 18 16 VCC = 5V, VREF = 5V, 2.5V 14 VIN(CM) = VREF(CM) 12 VIN = 0V FO = EXT CLOCK TA = 25C RES = LOG 2 (VREF/NOISERMS) 10 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 2488 F26 Figure 26. Resolution (NoiseRMS 1LSB) vs Output Data Rate and Reference Voltage RESOLUTION (BITS) RESOLUTION (BITS) Figure 22.-FS Error vs Output Data Rate and Temperature 20 2488 F23 Figure 23. Resolution (NoiseRMS 1LSB) vs Output Data Rate and Temperature 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 2488 F22 Figure 21. +FS Error vs Output Data Rate and Temperature RESOLUTION (BITS) RESOLUTION (BITS) Figure 20. Offset Error vs Output Data Rate and Temperature TA = 25C, 85C -3500 VIN(CM) = VREF(CM) VCC = VREF = 5V FO = EXT CLOCK 2488 F21 2488 F20 14 -2500 500 0 TA = 85C -2000 1000 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) TA = 25C -1500 1500 TA = 25C 0 -1000 TA = 85C 0 -10 -500 OFFSET ERROR (ppm OF VREF) 40 0 VIN(CM) = VREF(CM) VCC = VREF = 5V FO = EXT CLOCK -FS ERROR (ppm OF VREF) 3500 VIN(CM) = VREF(CM) VCC = VREF = 5V VIN = 0V FO = EXT CLOCK +FS ERROR (ppm OF VREF) OFFSET ERROR (ppm OF VREF) 50 VCC = VREF = 5V 16 VCC = 5V, VREF = 2.5V 14 VIN(CM) = VREF(CM) VIN = 0V 12 REF- = GND FO = EXT CLOCK TA = 25C RES = LOG 2 (VREF/INLMAX) 10 0 10 20 30 40 50 60 70 80 90 100 OUTPUT DATA RATE (READINGS/SEC) 2488 F27 Figure 27. Resolution (INLMAX 1LSB) vs Output Data Rate and Reference Voltage 2488fa 27 LTC2488 PACKAGE DESCRIPTION DE Package 14-Lead Plastic DFN (4mm x 3mm) (Reference LTC DWG # 05-08-1708 Rev B) 0.70 0.05 3.30 0.05 3.60 0.05 2.20 0.05 1.70 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 3.00 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED R = 0.115 TYP 4.00 0.10 (2 SIDES) R = 0.05 TYP 3.00 0.10 (2 SIDES) 8 0.40 0.10 14 3.30 0.10 1.70 0.10 PIN 1 NOTCH R = 0.20 OR 0.35 x 45 CHAMFER PIN 1 TOP MARK (SEE NOTE 6) (DE14) DFN 0806 REV B 7 0.200 REF 1 0.25 0.05 0.50 BSC 0.75 0.05 3.00 REF 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC PACKAGE OUTLINE MO-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 2488fa 28 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. LTC2488 REVISION HISTORY REV DATE DESCRIPTION A 7/10 Revised Typical Application drawing Added Note 18 PAGE NUMBER 1 4, 5 2488fa 29 LTC2488 TYPICAL APPLICATION 5V 5V R1 51.1k C4 0.1F 12 10F IIN+ = 0 R3 10k TO 100k IIN- = 0 R4 51.1k 14 8 5V 9 10 5V 102k 11 + 0.1F 10k TO 100k 7 1k LT1494 REF+ REF- CH0 2 SDI 3 SCK SDO 3-WIRE SPI INTERFACE 5 CH1 CH2 4 CS CH3 COM GND 6 2488 F28 0.1F - = EXTERNAL OSCILLATOR = INTERNAL OSCILLATOR 1 FO LTC2492 13 0.1F C3 0.1F VCC 1k 0.1F Figure 28. Easy Drive ADCs Simplify Measurement of High Impedance Sensors RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1236A-5 Precision Bandgap Reference, 5V 0.05% Max Initial Accuracy, 5ppm/C Drift LT1460 Micropower Series Reference 0.075% Max Initial Accuracy, 10ppm/C Max Drift LT1790 Micropower SOT-23 Low Dropout Reference Family 0.05% Max Initial Accuracy, 10ppm/C Max Drift LTC2400 24-Bit, No Latency ADC in SO-8 0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200A LTC2410 24-Bit, No Latency ADC with Differential Inputs 0.8VRMS Noise, 2ppm INL LTC2411/LTC2411-1 24-Bit, No Latency ADCs with Differential Inputs in MSOP 1.45VRMS Noise, 4ppm INL, Simultaneous 50Hz/60Hz Rejection (LTC2411-1) LTC2413 24-Bit, No Latency ADC with Differential Inputs Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise LTC2440 High Speed, Low Noise 24-Bit ADC 3.5kHz Output Rate, 200nV Noise, 24.6 ENOBs LTC2442 24-Bit, High Speed, 4-Channel/2-Channel ADC with Integrated Amplifier 8kHz Output Rate, 220nV Noise, Simultaneous 50Hz/60Hz Rejection LTC2449 24-Bit, High Speed, 8-Channel/16-Channel ADC 8kHz Output Rate, 200nV Noise, Simultaneous 50Hz/60Hz Rejection LTC2480/LTC2482/ LTC2484 16-Bit/24-Bit ADCs with Easy Drive Inputs, 600nV Noise, Programmable Gain, and Temperature Sensor Pin Compatible with 16-Bit and 24-Bit Versions LTC2481/LTC2483/ LTC2485 16-Bit/24-Bit ADCs with Easy Drive Inputs, 600nV Noise, I2C Interface, Programmable Gain, and Temperature Sensor Pin Compatible with 16-Bit and 24-Bit Versions LTC2492 2-Channel, 14-Channel 24-Bit ADC with Easy Drive Inputs and Temperature Sensor Pin Compatible with LTC2488 LTC2496/LTC2498 16-Channel/8-Channel 16-Bit/24-Bit ADC with Easy Drive Inputs and SPI Interface Timing Compatible with LTC2492 LTC2449 High Speed 16 Input, ADC 8kHz Output Rate, Variable Speed Resolution 2488fa 30 Linear Technology Corporation LT 0710 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2006