935287084551 - NXP SEMICONDUCTORS

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

1. General description

The LPC3220/30/40/50 embedded microcontrollers were designed for low power, high

performance applications. NXP achieved their performance goals using a 90 nanometer

process to implement an ARM926EJ-S CPU core with a vector floating point co-processor

and a large set of standard peripherals including USB On-The-Go. The

LPC3220/30/40/50 operates at CPU frequencies of up to 266 MHz.

The NXP implementation uses a ARM926EJ-S CPU core with a Harvard architecture,

5-stage pipeline, and an integral Memory Management Unit (MMU). The MMU provide s

the virtual memory capabilities needed to support the multi-programming demands of

modern operating systems. The ARM926EJ-S also has a hardware based set of DSP

instruction extensions, which includes single cycle MAC operations, and hardware based

native Jazelle Java Byte-code execution. The NXP implementation has a 32 kB

instruction cache and a 32 kB data cache.

For low power consumption, the LPC3220/30/40/50 ta kes advantage of NXP’s advanced

technology development to optimize intrinsic power and uses software controlled

architectural enhancements to optimize application based power management.

The LPC3220/30/40/50 also includes 256 kB of on-chip static RAM, a NAND flash

interface, an Ethernet MAC, an LCD controller that su pports STN and TF T panels, and an

external bus inte r fac e th at supp o rts SDR and DDR SDRAM as well as static devices. In

addition, the LPC3220/30/40/50 includes a USB 2.0 full-speed interface, seven UARTs,

two I2C-bus interfaces, two SPI/SSP ports, two I2S-bus interfaces, two single output

PWMs, a motor co ntrol PWM, six general purp ose timers with capture input s and compare

outputs, a Secure Digital (SD) interface, and a 10-bit Analog-to-Digital Converter (ADC)

with a touch screen sense option.

2. Features and benefits

ARM926EJS processor, running at CPU clock speeds up to 266 MHz.

Vector Floating Point (VFP) coprocessor.

32 kB instruction cache and 32 kB data cache.

Up to 256 kB of Internal SRAM (IRAM).

Selectable boot-up fr om var iou s ext er na l devices: NAND flash, SPI memory, USB,

UART, or static memory.

LPC3220/30/40/50

16/32-bit ARM microcontrollers; hardware floating-point

coprocessor, USB On-The-Go, and EMC memory interface

Rev. 01.03 — 16 March 2010 Product data sheet

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 2 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Multi-layer AHB system that provides a separate bus for each AHB master, including

both an instruction and data bus for the CPU, two data busses for the DMA controller,

and another bus for the USB controller, one for the LCD, and a final one for the

Ethernet MAC. There are no arbitration delays in the system unless two masters

attempt to access the same slave at the same time.

External memory controller for DDR and SDR SDRAM as well as for static devices.

Two NAND flash controllers: One for single-level NAND flash device s and the other for

multi-level NAND flash devices.

Master Interrupt Controller (MIC) and two Slave Interrupt Controllers (SIC), supporting

74 interrupt sources.

Eight channel General Purpose DMA (GPDMA) controller on the AHB that can be

used with the SD card port, the high-speed UARTs, I2S-bus interfaces, and SPI

interfaces, as well as memory-to-memory transfers.

Serial interfaces:

10/100 Ethernet MAC with dedicated DMA Controller.

USB interface supporting either device, host (OHCI compliant), or On-The-Go

(OTG) with an integral DMA controller and dedicated PLL to generate the required

48 MHz USB clock.

Four standa rd UAR Ts with fractional baud rate gen eration and 64 byte FIFOs. One

of the standard UARTs supports IrDA.

Three additional high-speed UARTs intended for on-board communications that

support baud rates up to 921 600 when using a 13 MHz main oscillator. All

high-speed UARTs provide 64 byte FIFOs.

Two SPI controllers.

Two SSP controllers.

Two I2C-bus interfaces with standard open-drain pins. The I2C-bus interfaces

support single master, slave, and multi-master I2C-bus configurations.

Two I2S-bus interfaces, each with separate input and output channels. Each

channel can be operated independently on three pins, or both input and output

channels can be used with only four pins and a shared clock.

Additional peripherals:

LCD controller supporting both STN and TFT panels, with dedicated DMA

controller. Programmable display resolution up to 1024 × 768.

Secure Digital (SD) memory card interface, which conforms to the SD Memory

Card Specification Version 1.01.

General Purpose (GP) input, output, and I/O pins. Includes 12 GP input pins, 24

GP output pins, and 51 GP I/O pins.

10-bit, 400 kHz Analog-to-Digital Converter (ADC) with input multiplexing from

three pins. Optionally, the ADC can operate as a touch screen controller.

Real-Time Clock (RTC) with separate power pin and dedicated 32 kHz oscillator.

NXP implemented the RTC in an independent on-chip power domain so it can

remain active while the rest of the chip is not powered. The RTC also includes a

32-byte scrat ch pad memory.

32-bit general pu rpose high-speed timer with a 16-bit pre-scaler. This timer

includes one external capture input pin a nd a capture conne ction to the RTC clock.

Interrupts may be generated using three match registers.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 3 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Six enhanced timer/counters which are architecturally identical except for the

peripheral base add ress. T wo cap ture inputs a nd two match output s are pinned ou t

to four timers. Timer 1 brings out a third match output, timers 2 and 3 bring out all

four match outputs, timer 4 has one match output, and timer 5 has no inputs or

outputs.

32-bit millisecond timer driven from the RTC clock. This timer can generate

interrupts using two match registers.

WatchDog timer clocked by the peripheral clock.

Two single-output PWM blocks.

Motor control PWM.

Keyboard scanner function allows automatic scanning of an up to 8 × 8 key matrix.

Up to 18 external interrupts.

Standard ARM test/debug interface for compatibility with existing tools.

Emulation Trace Buffer (ETB) with 2048 × 24 bit RAM allows trace via JTAG.

Stop mode saves power while allowing many peripheral functions to restart CPU

activity.

On-chip crystal oscillator.

An on-chip PLL allows CPU operation up to the maximum CPU rate without the

requirement for a high frequency crystal. Another PLL allows operation from the

32 kHz RTC clock rather than the external crystal.

Boundary scan for simplified board testing.

User-accessible unique serial ID number for each chip.

296 pin TFBGA package with a 15 × 15 × 0.7 mm body.

3. Applications

Consumer

Medical

Industrial

Network control

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  4 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
4. Ordering information
 
[1] F = −40 °C to +85 °C temperature range. Note that Revision “A” parts with and without the /01 suffix are identical. For example, 
LPC3220FET296 Revision “A” is identical to LPC3220FET296/01 Revision “A”. 
[2] Available in Revision “-” and “A”.
[3] Available starting with Revision “A”.
4.1 Ordering options
 
Ta ble 1. Ordering information
Type number[1] Package
Name Description Version
LPC3220FET296[2] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
LPC3230FET296[2] T FBGA296 plastic thin fine-pitch ball grid array package; 296 balls SOT1048-1
LPC3240FET296[2] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
LPC3250FET296[2] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
LPC3220FET296/01[3] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
LPC3230FET296/01[3] TFBGA296 plastic th in fine-pitch ball grid array package; 296 balls SOT1048-1
LPC3240FET296/01[3] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
LPC3250FET296/01[3] TFBGA296 plastic thin fine-pitch ball grid array package; 296 balls  SOT1048-1
Table 2. Part options
Type number SRAM (kB) 10/100 Ethernet LCD 
controller Temperature range (°C) Package
LPC3220FET296 128 0 0 −40 to +85 TFBGA296
LPC3230FET296 256 0 1 −40 to +85 TFBGA296
LPC3240FET296 256 1 0 −40 to +85 TFBGA296
LPC3250FET296 256 1 1 −40 to +85 TFBGA296
LPC3220FET296/01 128 0 0 −40 to +85 TFBGA296
LPC3230FET296/01 256 0 1 −40 to +85 TFBGA296
LPC3240FET296/01 256 1 0 −40 to +85 TFBGA296
LPC3250FET296/01 256 1 1 −40 to +85 TFBGA296

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 5 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

5. Block diagram

Fig 1. Block diagram of LPC3220/30/40/50

ARM

9EJS

D-CACHE

32 kB I-CACHE

32 kB

DATA INSTRUCTION

ethernet

PHY

interface

USB

transceiver

interface

LCD

panel

interface

EXTERNAL

MEMORY

CONTROLLER

ROM

16 kB

SRAM

256 kB

USB DMA ETBSDRAM

STANDARD

UART × 4

I2C

× 2

TIMERS

× 6

WATCHDOG

TIMER

DEBUG

SYSTEM

CONTROL HS UART

× 3

KEY

SCANNER 10-BIT

ADC/TS

UART

CONTROL

RTC

PWM

× 2 GPIO

M1M0

AHB

APB

BRIDGE

AHB

APB

BRIDGE

AHB

APB

BRIDGE

master layer 0123456

slave port 0

= Master/Slave connection supported

by the multilayer AHB matrix

32-bit AHB matrix

APB slaves

FAB slaves

AHB slaves APB slaves

port 3

port 4

port 0

32-bit wide

external

memory

ETB ETM 9

VFP9

LCDETHERNET

MOTOR

CONTROL PWM

002aae397

MMU

D-SIDE

CONTROLLER I-SIDE

CONTROLLER DMA

CONTROLLER

ETHERNET

10/100

MAC

USB OTG

CONTROLLER LCD

CONTROLLER

MLC

NAND

SLC

NAND SD

CARD

SPI

× 2 I2S

× 2

SSP

× 2

INTERRUPT

CONTROL

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 6 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

6. Pinning information

6.1 Pinning

Fig 2. Pin configuration for SOT 1048-1 (TFBGA296)

002aae398

Transparent top view

24681012

131415 17

16 18

1357911

ball A1

index area

Table 3. Pin allocation table (TFBGA296)

Pin Symbol Pin Symbol Pin Symbol

Row A

A3 I2C2_SCL

A4 I2S1TX_CLK/MAT3[0] A5 I2C1_SCL A6 MS_BS/MAT2[1]

A7 MS_DIO1/MAT0[1] A8 MS_DIO0/MAT0[0] A9 SPI2_DATIO/MOSI1/LCDVD[20][1]

A10 SPI2_DATIN/MISO1/

LCDVD[21][1]/GPI_27 A11 GPIO_1 A12 GPIO_0

A13 GPO_21/U4_TX/LCDVD[3][1] A14 GPO_15/MCOA1/LCDFP[1] A15 GPO_7/LCDVD[2][1]

A16 GPO_6/LCDVD[18][1]

Row B

B2 GPO_20 B3 GPO_5

B4 I2S1TX_WS/CAP3[0] B5 P0[0]/I2S1RX_CLK B6 I2C1_SDA

B7 MS_SCLK/MAT2[0] B8 MS_DIO2/MAT0[2] B9 SPI1_DATIO/MOSI0/MCI2

B10 SPI2_CLK/SCK1/LCDVD[23][1] B11 GPIO_4/SSEL1/LCDVD[22][1] B12 GPO_12/MCOA2/LCDLE[1]

B13 GPO_13/MCOB1/LCDDCLK[1] B14 GPO_2/MAT1[0]/LCDVD[0][1] B15 GPI_19/U4_RX

B16 GPI_8/KEY_COL6/

SPI2_BUSY/ENET_RX_DV[2] B17 n.c.

Row C

C1 FLASH_RD C2 GPO_19 C3 GPO_0/TST_CLK1

C4 USB_ATX_INT C5 USB_SE0_ VM/U5_TX C6 TST_CLK2

C7 GPI_6/HSTIM_CAP/

ENET_RXD2[2] C8 MS_DIO3/MAT0[3] C9 SPI1_CLK/SCK0

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  7 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
C10 SPI1_DATIN/MISO0/GPI_25/
MCI1 C11 GPIO_3/KEY_ROW7/
ENET_MDIO[2] C12 GPO_9/LCDVD[9][1]
C13 GPO_8/LCDVD[8][1] C14 GPI_2/CAP2[0]/
ENET_RXD3[2] C15 GPI_1/SERVICE
C16 GPI_0/I2S1RX_SDA C17 KEY_ROW4/ENET_TXD0[2] C18 KEY_ROW5/ENET_TXD1[2]
Row D
D1 FLASH_RDY D2 FLASH_ALE D3 GPO_14
D4 GPO_1 D5 USB_DAT_VP/U5_RX D6 USB_OE_TP
D7 P0[1]/I2S1RX_WS D8 GPO_4 D9 GPIO_2/KEY_ROW6/ENET_MDC[2]
D10 GPO_16/MCOB0/LCDENAB[1]/
LCDM[1] D11 GPO_18/MCOA0/LCDLP[1] D12 GPO_3/LCDVD[1][1]
D13 GPI_7/CAP4[0]/MCABORT D14 PWM_OUT1/LCDVD[16][1] D15 PWM_OUT2/INTSTAT/LCDVD[19][1]
D16 KEY_ROW3/ENET_TX_EN[2] D17 KEY_COL2/ENET_RX_ER[2] D18 KEY_COL3/ENET_CRS[2]
Row E
E1 FLASH_IO[3] E2 FLASH_IO[7] E3 FLASH_CE
E4 I2C2_SDA E5 USB_I2C_SCL E6 USB_I2C_SDA
E7 I2S1TX_SDA/MAT3[1] E8 GPO_11 E9 GPIO_5/SSEL0/MCI0
E10 GPO_22/U7_HRTS/
LCDVD[14][1] E11 GPO_10/MCOB2/LCDPWR[1] E12 GPI_9/KEY_COL7/ENET_COL[2]
E13 GPI_4/SPI1_BUSY E14 KEY_ROW1/ENET_TXD2[2] E15 KEY_ROW0/ENET_TX_ER[2]
E16 KEY_COL1/ENET_RX_CLK[2]/
ENET_REF_CLK[2] E17 U7_RX/CAP0[0]/
LCDVD[10][1]/GPI_23 E18 U7_TX/MAT1[1]/LCDVD[11][1]
Row F
F1 FLASH_IO[2] F2 FLASH_WR F3 FLASH_CLE
F4 GPI_3 F5 VSS_IOC F6 VSS_IOB
F7 VDD_IOC F8 VDD_IOB F9 VDD_IOD
F10 VSS_IOD F11 VSS_IOD F12 VSS_IOD
F13 VDD_IOD F14 KEY_ROW2/ENET_TXD3[2] F15 KEY_COL0/ENET_TX_CLK[2]
F16 KEY_COL5/ENET_RXD1[2] F17 U6_IRRX/GPI_21 F18 U5_RX/GPI_20
Row G
G1 EMC_DYCS1 G2 FLASH_IO[5] G3 FLASH_IO[6]
G4 RESOUT G5 VSS_IOC G6 VDD_IOC
G7 VDD_CORE G8 VSS_CORE G9 VDD_CORE
G10 VSS_CORE G11 VDD_CORE G12 VSS_CORE
G13 U7_HCTS/CAP0[1]/
LCDCLKIN[1]/GPI_22 G14 DBGEN G15 KEY_COL4/ENET_RXD0[2]
G16 U6_IRTX G17 SYSCLKEN/LCDVD[15][1] G18 JTAG_TMS
Row H
H1 EMC_OE H2 FLASH_IO[0] H3 FLASH_IO[1]
H4 FLASH_IO[4] H5 VSS_IOC H6 VDD_IOC
H7 VSS_CORE H12 VSS_IOD
H13 VDD_IOA H14 JTAG_TCK H15 U5_TX
Table 3. Pin allocation table (TFBGA296)
Pin Symbol Pin Symbol Pin Symbol

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 8 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

H16 HIGHCORE/LCDVD[17][1] H17 JTAG_NTRST H18 JTAG_RTCK

Row J

J1 EMC_A[20]/P1[20] J2 EMC_A[21]/P1[21] J3 EMC_A[22]/P1[22]

J4 EMC_A[23]/P1[23] J5 VDD_IOC J6 VDD_EMC

J7 VDD_CORE J12 VDD_CORE

J13 VDD_IOA J14 U3_RX/GPI_18 J15 JTAG_TDO

J16 JTAG_TDI J17 U3_TX J18 U2_HCTS/U3_CTS/GPI_16

Row K

K1 EMC_A[19]/P1[19] K2 EMC_A[18]/P1[18] K3 EMC_A[16]/P1[16]

K4 EMC_A[17]/P1[17] K5 VSS_EMC K6 VDD_EMC

K7 VDD_EMC K12 VSS_CORE

K13 VSS_IOA K14 VDD_RTC K15 U1_RX/CAP1[0]/GPI_15

K16 U1_TX K17 U2_TX/U3_DTR K18 U2_RX/U3_DSR/GPI_17

Row L

L1 EMC_A[15]/P1[15] L2 EMC_CKE1 L3 EMC_A[0]/P1[0]

L4 EMC_A[1]/P1[1] L5 VSS_EMC L6 VDD_EMC

L7 VSS_CORE L12 VDD_COREFXD

L13 VDD_RTCCORE L14 VSS_RTCCORE L15 P0[4]/I2S0RX_WS/LCDVD[6][1]

L16 P0[5]/I2S0TX_SDA/LCDVD[7][1] L17 P0[6]/I2S0TX_CLK/

LCDVD[12][1] L18 P0[7]/I2S0TX_WS/LCDVD[13][1]

Row M

M1 EMC_A[2]/P1[2] M2 EMC_A[3]/P1[3] M3 EMC_A[4]/P1[4]

M4 EMC_A[8]/P1[8] M5 VSS_EMC M6 VDD_EMC

M7 VDD_CORE M8 VDD_EMC M9 VSS_CORE

M10 VSS_CORE M11 VDD_CORE M12 VSS_CORE

M13 VDD_COREFXD M14 RESET M15 ONSW

M16 GPO_23/U2_HRTS/U3_RTS M17 P0[2]/I2S0RX_SDA/

LCDVD[4][1] M18 P0[3]/I2S0RX_CLK/LCDVD[5][1]

Row N

N1 EMC_A[5]/P1[5] N2 EMC_A[6]/P1[6] N3 EMC_A[7/P1[7]

N4 EMC_A[12]/P1[12] N5 VSS_EMC N6 VSS_EMC

N7 VDD_EMC N8 VDD_EMC N9 VDD_EMC

N10 VDD_EMC N11 VDD_EMC N12 VDD_AD

N13 VDD_AD N14 VDD_FUSE N15 VDD_RTCOSC

N16 GPI_5/U3_DCD N17 GPI_28/U3_RI N18 GPO_17

Row P

P1 EMC_A[9]/P1[9] P2 EMC_A[10]/P1[10] P3 EMC_A[11]/P1[11]

P4 EMC_DQM[1] P5 EMC_DQM[3] P6 VSS_EMC

Table 3. Pin allocation table (TFBGA296)

Pin Symbol Pin Symbol Pin Symbol

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 9 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

[1] LCD on LPC3230 and LPC3250 only.

[2] Ethernet on LPC3240 and LPC3250 only.

P7 VSS_EMC P8 VSS_EMC P9 VSS_EMC

P10 VSS_EMC P11 VSS_EMC P12 EMC_BLS[3]

P13 VSS_AD P14 VSS_OSC P15 VDD_PLLUSB

P16 RTCX_IN P17 RTCX_OUT P18 VSS_RTCOSC

Row R

R1 EMC_A[13]/P1[13] R2 EMC_A[14]/P1[14] R3 EMC_DQM[0]

R4 EMC_WR R5 EMC_CAS R6 EMC_DYCS0

R7 EMC_D[1] R8 EMC_D[7] R9 EMC_D[17]/EMC_DQS1

R10 EMC_D[24]/P2[5] R11 EMC_CS1 R12 EMC_BLS[2]

R13 TS_XP R14 PLL397_LOOP R15 SYSX_OUT

R16 VSS_PLLUSB R17 VDD_PLLHCLK R18 VSS_PLLHCLK

Row T

T1 EMC_DQM[2] T2 EMC_RAS T3 EMC_CLK

T4 EMC_CLKIN T5 EMC_D[2] T6 EMC_D[6]

T7 EMC_D[11] T8 EMC_D[14] T9 EMC_D[20]/P2[1]

T10 EMC_D[23]/P2[4] T11 EMC_D[27]/P2[8] T12 EMC_CS2

T13 EMC_BLS[1] T14 ADIN1/TS_XM T15 VSS_PLL397

T16 VDD_PLL397 T17 SYSX_IN T18 VDD_OSC

Row U

U2 n.c. U3 EMC_CKE0

U4 EMC_D[0] U5 EMC_D[3] U6 EMC_D[9]

U7 EMC_D[12] U8 EMC_D[15] U9 EMC_D[19]/P2[0]

U10 EMC_D[22]/P2[3] U11 EMC_D[26]/P2[7] U12 EMC_D[30]/P2[11]

U13 EMC_CS0 U14 EMC_BLS[0] U15 ADIN0/TS_YM

U16 TS_YP U17 n.c.

Row V

V3 EMC_D[4]

V4 EMC_D[5] V5 EMC_D[8] V6 EMC_D[10]

V7 EMC_D[13] V8 EMC_D[16]/EMC_DQS0 V9 EMC_D[18]/EMC_CLK

V10 EMC_D[21]/P2[2] V11 EMC_D[25]/P2[6] V12 EMC_D[28]/P2[9]

V13 EMC_D[29]/P2[10] V14 EMC_D[31]/P2[12] V15 EMC_CS3

V16 ADIN2/TS_AUX_IN

Table 3. Pin allocation table (TFBGA296)

Pin Symbol Pin Symbol Pin Symbol

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 10 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

6.2 Pin description

Table 4. Pin description

Symbol Pin Power supply

domain Type Description

ADIN0/TS_YM U15 VDD_AD analog in ADC input 0/touch screen Y minus

ADIN1/TS_XM T14 VDD_AD analog in ADC input 0/touch screen X minus

ADIN2/TS_AUX_IN V16 VDD_AD analog in ADC input 2/ touch screen AUX input

DBGEN G14 VDD_IOD I: PD Device test input

LOW = JTAG in-circuit de bug available; normal

operation.

HIGH = I/O cell boundary scan test; for board

assembly BSDL test.

EMC_A[0]/P1[0] L3 VDD_EMC I/O EMC address bit 0

I/O Port 1 GPIO bit 0

EMC_A[1]/P1[1] L4 VDD_EMC I/O EMC address bit 1

I/O Port 1 GPIO bit 1

EMC_A[2]/P1[2] M1 VDD_EMC I/O EMC address bit 2

I/O Port 1 GPIO bit 2

EMC_A[3]/P1[3] M2 VDD_EMC I/O EMC address bit 3

I/O Port 1 GPIO bit 3

EMC_A[4]/P1[4] M3 VDD_EMC I/O EMC address bit 4

I/O Port 1 GPIO bit 4

EMC_A[5]/P1[5] N1 VDD_EMC I/O EMC address bit 5

I/O Port 1 GPIO bit 5

EMC_A[6]/P1[6] N2 VDD_EMC I/O EMC address bit 6

I/O Port 1 GPIO bit 6

EMC_A[7/P1[7] N3 VDD_EMC I/O EMC address bit 7

I/O Port 1 GPIO bit 7

EMC_A[8]/P1[8] M4 VDD_EMC I/O EMC address bit 8

I/O Port 1 GPIO bit 8

EMC_A[9]/P1[9] P1 VDD_EMC I/O EMC address bit 9

I/O Port 1 GPIO bit 9

EMC_A[10]/P1[10] P2 VDD_EMC I/O EMC address bit 10

I/O Port 1 GPIO bit 10

EMC_A[11]/P1[11] P3 VDD_EMC I/O EMC address bit 11

I/O Port 1 GPIO bit 11

EMC_A[12]/P1[12] N4 VDD_EMC I/O EMC address bit 12

I/O Port 1 GPIO bit 12

EMC_A[13]/P1[13] R1 VDD_EMC I/O EMC address bit 13

I/O Port 1 GPIO bit 13

EMC_A[14]/P1[14] R2 VDD_EMC I/O EMC address bit 14

I/O Port 1 GPIO bit 14

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 11 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

EMC_A[15]/P1[15] L1 VDD_EMC I/O EMC address bit 15

I/O Port 1 GPIO bit 15

EMC_A[16]/P1[16] K3 VDD_EMC I/O EMC address bit 16

I/O Port 1 GPIO bit 16

EMC_A[17]/P1[17] K4 VDD_EMC I/O EMC address bit 17

I/O Port 1 GPIO bit 17

EMC_A[18]/P1[18] K2 VDD_EMC I/O EMC address bit 18

I/O Port 1 GPIO bit 18

EMC_A[19]/P1[19] K1 VDD_EMC I/O EMC address bit 19

I/O Port 1 GPIO bit 19

EMC_A[20]/P1[20] J1 VDD_EMC I/O EMC address bit 20

I/O Port 1 GPIO bit 20

EMC_A[21]/P1[21] J2 VDD_EMC I/O EMC address bit 21

I/O Port 1 GPIO bit 21

EMC_A[22]/P1[22] J3 VDD_EMC I/O EMC address bit 22

I/O Port 1 GPIO bit 22

EMC_A[23]/P1[23] J4 VDD_EMC I/O EMC address bit 23

I/O Port 1 GPIO bit 23

EMC_BLS[0] U14 VDD_EMC O Static memory byte lane 0 select

EMC_BLS[1] T13 VDD_EMC O Static memory byte lane 1 select

EMC_BLS[2] R12 VDD_EMC O Static memory byte lane 2 select

EMC_BLS[3] P12 VDD_EMC O Static memory byte lane 3 select

EMC_CAS R5 VDD_EMC O SDRAM column address strobe out, active LOW

EMC_CKE0 U3 VDD_EMC O Clock enable out for SDRAM bank 0

EMC_CKE1 L2 VDD_EMC O Clock enable out for SDRAM bank 1

EMC_CLK T3 VDD_EMC O SDRAM clock out

EMC_CLKIN T4 VDD_EMC I SDRAM clock feedback

EMC_CS0 U13 VDD_EMC O EMC static memory chip select 0

EMC_CS1 R11 VDD_EMC O EMC static memory chip select 1

EMC_CS2 T12 VDD_EMC O EMC static memory chip select 2

EMC_CS3 V15 VDD_EMC O EMC static memory chip select 3

EMC_D[0] U4 VDD_EMC I/O: BK EMC data bit 0

EMC_D[1] R7 VDD_EMC I/O: BK EMC data bit 1

EMC_D[2] T5 VDD_EMC I/O: BK EMC data bit 2

EMC_D[3] U5 VDD_EMC I/O: BK EMC data bit 3

EMC_D[4] V3 VDD_EMC I/O: BK EMC data bit 4

EMC_D[5] V4 VDD_EMC I/O: BK EMC data bit 5

EMC_D[6] T6 VDD_EMC I/O: BK EMC data bit 6

EMC_D[7] R8 VDD_EMC I/O: BK EMC data bit 7

EMC_D[8] V5 VDD_EMC I/O: BK EMC data bit 8

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 12 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

EMC_D[9] U6 VDD_EMC I/O: BK EMC data bit 9

EMC_D[10] V6 VDD_EMC I/O: BK EMC data bit 10

EMC_D[11] T7 VDD_EMC I /O: BK EMC data bit 11

EMC_D[12] U7 VDD_EMC I/O: BK EMC data bit 12

EMC_D[13] V7 VDD_EMC I/O: BK EMC data bit 13

EMC_D[14] T8 VDD_EMC I/O: BK EMC data bit 14

EMC_D[15] U8 VDD_EMC I/O: BK EMC data bit 15

EMC_D[16]/

EMC_DQS0 V8 VDD_EMC I/O: BK EMC data bit 16

I/O: BK DDR data strobe 0

EMC_D[17]/

EMC_DQS1 R9 VDD_EMC I/O: BK EMC data bit 17

I/O: BK DDR data strobe 1

EMC_D[18]/

EMC_CLK V9 VDD_EMC I/O: P EMC data bit 18

I/O: P DDR inverted clock output

EMC_D[19]/P2[0] U9 VDD_EMC I/O: P EMC data bit 19

I/O: P Port 2 GPIO bit 0

EMC_D[20]/P2[1] T9 VDD_EMC I/O: P EMC data bit 20

I/O: P Port 2 GPIO bit 1

EMC_D[21]/P2[2] V10 VDD_EMC I/O: P EMC data bit 21

I/O: P Port 2 GPIO bit 2

EMC_D[22]/P2[3] U10 VDD_EMC I/O: P EMC data bit 22

I/O: P Port 2 GPIO bit 3

EMC_D[23]/P2[4] T10 VDD_EMC I/O: P EMC data bit 23

I/O: P Port 2 GPIO bit 4

EMC_D[24]/P2[5] R10 VDD_EMC I/O: P EMC data bit 24

I/O: P Port 2 GPIO bit 5

EMC_D[25]/P2[6] V11 VDD_EMC I/O: P EMC data bit 25

I/O: P Port 2 GPIO bit 6

EMC_D[26]/P2[7] U11 VDD_EMC I/O: P EMC data bit 26

I/O: P Port 2 GPIO bit 7

EMC_D[27]/P2[8] T11 VDD_EMC I/O: P EMC data bit 27

I/O: P Port 2 GPIO bit 8

EMC_D[28]/P2[9] V12 VDD_EMC I/O: P EMC data bit 28

I/O: P Port 2 GPIO bit 9

EMC_D[29]/P2[10] V13 VDD_EMC I/O: P EMC data bit 29

I/O: P Port 2 GPIO bit 10

EMC_D[30]/P2[11] U12 VDD_EMC I/O: P EMC data bit 30

I/O: P Port 2 GPIO bit 11

EMC_D[31]/P2[12] V14 VDD_EMC I/O: P EMC data bit 31

I/O: P Port 2 GPIO bit 12

EMC_DQM[0] R3 VDD_EMC O SDRAM data mask 0 out

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 13 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

EMC_DQM[1] P4 VDD_EMC O SDRAM data mask 1 out

EMC_DQM[2] T1 VDD_EMC O SDRAM data mask 2 out

EMC_DQM[3] P5 VDD_EMC O SDRAM data mask 3 out

EMC_DYCS0 R6 VDD_EMC O SDRAM active LOW chip select 0

EMC_DYCS1 G1 VDD_EMC O SDRAM active LOW chip select 1

EMC_OE H1 VDD_EMC O EMC static memory output enable

EMC_RAS T2 VDD_EMC O SDRAM row address strobe, active LOW

EMC_WR R4 VDD_EMC O EMC write strobe, active LOW

FLASH_ALE D2 VDD_IOC O Flash address latch enable

FLASH_CE E3 VDD_IOC O Flash chip enable

FLASH_CLE F3 VDD_IOC O Flash command latch enable

FLASH_IO[0] H2 VDD_IOC I/O: BK Flash data bus, bit 0

FLASH_IO[1] H3 VDD_IOC I/O: BK Flash data bus, bit 1

FLASH_IO[2] F1 VDD_IOC I/O: BK Flash data bus, bit 2

FLASH_IO[3] E1 VDD_IOC I/O: BK Flash da ta bus, bit 3

FLASH_IO[4] H4 VDD_IOC I/O: BK Flash data bus, bit 4

FLASH_IO[5] G2 VDD_IOC I/O: BK Flash data bus, bit 5

FLASH_IO[6] G3 VDD_IOC I/O: BK Flash data bus, bit 6

FLASH_IO[7] E2 VDD_IOC I/O: BK Flash da ta bus, bit 7

FLASH_RD C1 VDD_IOC O Flash read enable

FLASH_RDY D1 VDD_IOC I Flash ready (from flash device)

FLASH_WR F2 VDD_IOC O Flash write enable

GPI_0/I2S1RX_SDA C16 VDD_IOD I General purpose input 0

I I2S1 Receive data

GPI_1/SERVICE C15 VDD_IOD I General purpose input 1

I Boot select input

GPI_2/CAP2[0]/

ENET_RXD3 C14 VDD_IOD I General purpose input 2

I Timer 2 capture input 0

I Ethernet receive data 3 (LPC3240 and LPC3250

only)

GPI_3 F4 VDD_IOC I General purpose input 3

GPI_4/SPI1_BUSY E13 VDD_IOD I General purpose input 4

I SPI1 busy input

GPI_5/U3_DCD N16 VDD_IOA I General purpose input 5

I UART 3 data carrier detect input

GPI_6/

HSTIM_CAP/

ENET_RXD2

C7 VDD_IOB I General purpose input 6

I High-speed timer capture input

I Ethernet receive data 2 (LPC3240 and LPC3250

only)

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 14 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

GPI_7/CAP4[0]/

MCABORT D13 VDD_IOD I General purpose input 7

I Timer 4 capture input 0

I Motor control PWM LOW-active fast abort input

GPI_8/KEY_COL6/

SPI2_BUSY/

ENET_RX_DV

B16 VDD_IOD I General purpose input 8

I Keyscan column 6 input

I SPI2 busy input

I Ethernet receive data valid input (LPC3240 and

LPC3250 only)

GPI_9/KEY_COL7/

ENET_COL E12 VDD_IOD I General purpose input 9

I Keyscan column 7 input

I Ethernet collision input (LPC3240 and LPC3250

only)

GPI_19/U4_RX B15 VDD_IOD I General purpose input 19

I UART 4 receive

GPI_28/U3_RI N17 VDD_IOA I General purpose input 28

I UART 3 ring indicator input

GPIO_0 A12 VDD_IOD I/O General purp ose input/output 0

GPIO_1 A11 VDD_IOD I/O General purpose input/output 1

GPIO_2/

KEY_ROW6/

ENET_MDC

D9 VDD_IOD I/O General purpose input/output 2

O Keyscan row 6 output

O Ethernet PHY interface clock (LPC3240 and

LPC3250 only)

GPIO_3/

KEY_ROW7/

ENET_MDIO

C11 VDD_IOD I/O General purpose input/output 3

I/O Keyscan row 7 output

I/O Ethernet PHY interface data (LPC3240 and

LPC3250 only)

GPIO_4/

SSEL1/

LCDVD[22]

B11 VDD_IOD I/O General purpose input/output 4

I/O SSP1 Slave Select

I/O LCD data bit 22 (LPC3230 and LPC3250 only)

GPIO_5/

SSEL0/

MCI0

E9 VDD_IOD I/O General purpose input/output 5

I/O SSP0 Slave Select

I/O Motor control channel 0 input

GPO_0/

TST_CLK1 C3 VDD_IOC O General purpose output 0

O Test clock 1 out

GPO_1 D4 VDD_IOC O General purpose output 1

GPO_2/

MAT1[0]/

LCDVD[0]

B14 VDD_IOD O General purpose output 2

O Timer 1 match output 0

O LCD data bit 0 (LPC3230 and LPC3250 only)

GPO_3/

LCDVD[1] D12 VDD_IOD O Gene ral purpose output 3

O LCD data bit 1 (LPC3230 and LPC3250 only)

GPO_4 D8 VDD_IOB O General purpose output 4

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 15 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

GPO_5 B3 VDD_IOC O General purpose output 5

GPO_6/

LCDVD[18] A16 VDD_IOD O General purpose output 6

O LCD data bit 18 (LPC3230 and LPC3250 only)

GPO_7/

LCDVD[2] A15 VDD_IOD O General purpose output 7

O LCD data bit 2 (LPC3230 and LPC3250 only)

GPO_8/

LCDVD[8] C13 VDD_IOD O Gene ral purpose output 8

O LCD data bit 8 (LPC3230 and LPC3250 only)

GPO_9/

LCDVD[9] C12 VDD_IOD O Gene ral purpose output 9

O LCD data bit 9 (LPC3230 and LPC3250 only)

GPO_10/

MCOB2/

LCDPWR

E11 VDD_IOD O General purpose output 10

O Motor control PWM channel 2, output B

O LCD panel power enable (LPC3230 and LPC3250

only)

GPO_11 E8 VDD_IOB O General purpose output 11

GPO_12/

MCOA2/

LCDLE

B12 VDD_IOD O General purpose output 12

O Motor control PWM channel 2, output A

O LCD line end signal (LPC3230 and LPC3250 only)

GPO_13/

MCOB1/

LCDDCLK

B13 VDD_IOD O General purpose output 13

O Motor control PWM channel 1, output B

O LCD clock output (LPC3230 and LPC3250 only)

GPO_14 D3 VDD_IOC O General purpose output 14

GPO_15/

MCOA1/

LCDFP

A14 VDD_IOD O General purpose output 15

O Motor control PWM channel 1, output A

O LCD frame/sync pulse (LPC3230 and LPC3250

only)

GPO_16/

MCOB0/

LCDENAB/LCDM

D10 VDD_IOD O General purpose output 16

O Motor control PWM channel 0, output B

O LCD STN AC bias/TF T data enable (LPC3230 and

LPC3250 only)

GPO_17 N18 VDD_IOA O General purpose output 17

GPO_18/

MCOA0/

LCDLP

D11 VDD_IOD O General purpose output 18

O Motor control PWM channel 0, output A

O LCD line sync/horizontal sync (LPC3230 and

LPC3250 only)

GPO_19 C2 VDD_IOC O General purpose output 19

GPO_20 B2 VDD_IOC O General purpose output 20

GPO_21/

U4_TX/

LCDVD[3]

A13 VDD_IOD O General purpose output 21

O UART 4 transmit

O LCD data bit 3 (LPC3230 and LPC3250 only)

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 16 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

GPO_22/

U7_HRTS/

LCDVD[14]

E10 VDD_IOD O General purpose output 22

O HS UART 7 RTS out

O LCD data bit 14 (LPC3230 and LPC3250 only)

GPO_23/

U2_HRTS/

U3_RTS

M16 VDD_IOA O General purpose output 23

OHS UART 2 RTS out

O UART 3 RTS out

HIGHCORE/

LCDVD[17] H16 VDD_IOD O Core voltage control out

O LCD data bit 17 (LPC3230 and LPC3250 only)

I2C1_SCL A5 VDD_IOB I/O T I2C1 serial clock input/output

I2C1_SDA B6 VDD_IOB I/O T I2C1 serial data input/output

I2C2_SCL A3 VDD_IOC I/O T I2C2 serial clock input/output

I2C2_SDA E4 VDD_IOC I/O T I2C2 serial data input/output

I2S1TX_CLK/

MAT3[0] A4 VDD_IOB I/O I2S1 transmit clock

O Timer 3 match output 0

I2S1TX_SDA/

MAT3[1] E7 VDD_IOB I/O I2S1 transmit data

O Timer 3 match output 1

I2S1TX_WS/

CAP3[0] B4 VDD_IOB I/O I2S1 transmit word select

I/O Timer 3 capture input 0

JTAG_NTRST H1 7 VDD_IOD I: PU JTAG1 reset input

JTAG_RTCK H18 VDD_IOD O JTAG1 return clock out

JTAG_TCK H1 4 VDD_IOD I JTAG1 clock input

JTAG_TDI J16 VDD_IOD I: PU JTAG1 data input

JTAG_TDO J15 VDD_IOD O JTAG1 data out

JTAG_TMS G18 VDD_IOD I: PU TAG1 test mode select input

KEY_COL0/

ENET_TX_CLK F15 VDD_IOD I Keyscan column 0 input

I Ethernet transmit clock (LPC3240 and LPC3250

only)

KEY_COL1/

ENET_RX_CLK/

ENET_REF_CLK

E16 VDD_IOD I Keyscan column 1 input

I Ethernet receive clock (MII mode, LPC3240 and

LPC3250 only)

I Ethernet reference clock (RMII mode, LPC3240 and

LPC3250 only)

KEY_COL2/

ENET_RX_ER D17 VDD_IOD I Keyscan column 2 input

I Ethernet receive error input (LPC3240 and

LPC3250 only)

KEY_COL3/

ENET_CRS D18 VDD_IOD I Keyscan column 3 input

I Ethernet carrier sense input (LPC3240 and

LPC3250 only)

KEY_COL4/

ENET_RXD0 G15 VDD_IOD I Keyscan column 4 input

I Ethernet receive data 0 (LPC3240 and LPC3250

only)

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 17 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

KEY_COL5/

ENET_RXD1 F16 VDD_IOD I Keyscan column 5 input

I Ethernet receive data 1 (LPC3240 and LPC3250

only)

KEY_ROW0/

ENET_TX_ER E15 VDD_IOD I/O T Keyscan row 0 out

I/O T Ethernet transmit error (LPC3240 and LPC3250

only)

KEY_ROW1/

ENET_TXD2 E14 V D D _ IOD I/O T Keyscan row 1 ou t

I/O T Ethernet transmit data 2 (LPC3240 and LPC3250

only)

KEY_ROW2/

ENET_TXD3 F14 VDD_IOD I/O T Keyscan row 2 out

I/O T Ethernet transmit data 3 (LPC3240 and LPC3250

only)

KEY_ROW3/

ENET_TX_EN D16 VDD_IOD I/O T Keyscan row 3 out

I/O T Ethernet transmit enable (LPC3240 and LPC3250

only)

KEY_ROW4/

ENET_TXD0 C17 VDD_IOD I/O T Keyscan row 4 out

I/O T Ethernet transmit data 0 (LPC3240 and LPC3250

only)

KEY_ROW5/

ENET_TXD1 C18 VDD_IOD I/O T Keyscan row 5 out

I/O T Ethernet transmit data 1 (LPC3240 and LPC3250

only)

MS_BS/MAT2[1] A6 VDD_IOD I/O: P MS/SD card command out

O Timer 2 match output 1

MS_DIO0/MAT0[0] A8 VDD_IOD I/O: P MS/SD card data 0

O Timer 0 match output 0

MS_DIO1/

MAT0[1] A7 VDD_IOD I/O: P MS/SD card data 1

O Timer 0 match output 1

MS_DIO2/

MAT0[2] B8 VDD_IOD I/O: P MS/SD card data 2

O Timer 0 match output 2

MS_DIO3/

MAT0[3] C8 VDD_IOD I/O: P MS/SD card data 3

O Timer 0 match output 3

MS_SCLK/

MAT2[0] B7 VDD_IOD I/O MS/SD card clock output

O Timer 2 match output 0

n.c. B17,

U17,

- - not connected

ONSW M15 VDD_RTC O RTC match output for external power control

P0[0]/

I2S1RX_CLK B5 VDD_IOB I/O Port 0 GPIO bit 0

I/O I2S1 receive clock

P0[1]/

I2S1RX_WS D7 VDD_IOB I/O Port 0 GPIO bit 1

I/O I2S1 receive word select

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 18 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

P0[2]/

I2S0RX_SDA/

LCDVD[4]

M17 VDD_IOA I/O Port 0 GPIO bit 2

I/O I2S0 receive data

I/O LCD data bit 4 (LPC3230 and LPC3250 only)

P0[3]/

I2S0RX_CLK/

LCDVD[5]

M18 VDD_IOA I/O Port 0 GPIO bit 3

I/O I2S0 receive clock

I/O LCD data bit 5 (LPC3230 and LPC3250 only)

P0[4]/

I2S0RX_WS/

LCDVD[6]

L15 VDD_IOA I/O Port 0 GPIO bit 4

I/O I2S0 receive word select

I/O LCD data bit 6 (LPC3230 and LPC3250 only)

P0[5]/

I2S0TX_SDA/

LCDVD[7]

L16 VDD_IOA I/O Port 0 GPIO bit 5

I/O I2S0 transmit data

I/O LCD data bit 7 (LPC3230 and LPC3250 on ly)

P0[6]/

I2S0TX_CLK/

LCDVD[12]

L17 VDD_IOA I/O Port 0 GPIO bit 6

I/O I2S0 transmit clock

I/O LCD data bit 12 (LPC3230 and LPC3250 only)

P0[7]/

I2S0TX_WS/

LCDVD[13]

L18 VDD_IOA I/O Port 0 GPIO bit 7

I/O I2S0 transmit word select

I/O LCD data bit 13 (LPC3230 and LPC3250 only)

PLL397_LOOP R14 VDD_AD analog filter PLL397 loop filter

(for external components)

PWM_OUT1/

LCDVD[16] D14 VDD_IOD O PWM1 out

O LCD data bit 16 (LPC3230 and LPC3250 only)

PWM_OUT2/INTSTAT/

LCDVD[19] D15 VDD_IOD O PWM2 output/internal interrupt status[1]

O LCD data bit 19 (LPC3230 and LPC3250 only)

RESET M14 VDD_R T C I Reset input, active LOW

RESOUT G4 VDD_IOC O Reset out. Reflects external and WDT reset

RTCX_IN P16 VDD_RTC analog in RTC oscillator input

RTCX_OUT P17 VDD_RTC analog out RTC oscillator output

SPI1_CLK/

SCK0 C9 VDD_IOD O SPI1 clock out

O SSP0 clock out

SPI1_DATIN/

MISO0/

GPI_25/

MCI1

C10 VDD_IOD I/O SPI1 data in

I/O SSP0 MISO

I/O General purpose input bit 25

I Motor control channel 1 input

SPI1_DATIO/

MOSI0/

MCI2

B9 VDD_IOD I/O SPI1 data out (and optional input)

I/O SSP0 MOSI

I Motor control channel 2 input

SPI2_CLK/

SCK1/

LCDVD[23]

B10 VDD_IOD I /O SPI2 clock out

I/O SSP1 clock out

I/O LCD data bit 23 (LPC3230 and LPC3250 only)

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 19 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

SPI2_DATIO/

MOSI1/

LCDVD[20]

A9 VDD_IOD I/O SPI2 data out (and opti onal input)

I/O SSP1 MOSI

I/O LCD data bit 20 (LPC3230 and LPC3250 only)

SPI2_DATIN/

MISO1/

LCDVD[21]/

GPI_27

A10 VDD_IOD I/O SPI2 data in

I/O SSP1 MISO

I/O LCD data 21 (LPC3230 and LPC3250 only)

I/O General purpose input bit 27

SYSCLKEN/

LCDVD[15] G17 VDD_IOD I/O T Clock request out for external clock source

I/O T LCD data bit 15 (LPC3230 and LPC3250 only)

SYSX_IN T17 VDD_OSC analog in System clock oscillator input

SYSX_OUT R15 VDD_OSC analog out System clock oscillator output

TS_XP R13 VDD_AD I/O Touchscreen X output

TS_YP U16 VDD_AD I/O Touchscreen Y output

TST_CLK2 C6 VDD_IOB O Test clock 2 out

U1_RX/CAP1[0]/

GPI_15 K15 VDD_IOA I/O HS UART 1 receive

I/O T imer 1 capture input 0

I/O General purpose input bit 15

U1_TX K16 VDD_IOA O HS UART 1 transmit

U2_HCTS/

U3_CTS/GPI_16 J18 VDD_IOA I/O H S UART 2 Clear to Send input

I UART 3 Clear to Send

I/O General purpose input bit 16

U2_RX/

U3_DSR/GPI_17 K18 VDD_IOA I/O HS UART 2 receive

I/O UART 3 data set ready

I/O General purpose input bit 17

U2_TX/U3_DTR K17 VDD_IOA O HS UART 2 transmit

O UART 3 data terminal ready out

U3_RX/

GPI_18 J14 VDD_IOD I /O UART 3 receive

I/O General purpose input bit 18

U3_TX J17 VDD_IOD O UART 3 transmit

U5_RX/

GPI_20 F18 VDD_IOD I/O UART 5 receive

I General purpose input bit 20

U5_TX H15 VDD_IOD O UART 5 transmit

U6_IRRX/

GPI_21 F17 VDD_IOD I/O UART 6 receive (with IrDA)

I General purpose input bit 21

U6_IRTX G16 VDD_IOD O UART 6 transmit (with IrDA)

U7_HCTS/

CAP0[1]/

LCDCLKIN/

GPI_22

G13 VDD_IOD I HS UART 7 CTS in

I Timer 0 capture input 1

I LCD panel clock in (LPC3230 and LPC3250 only)

I General purpose input bit 22

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 20 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

U7_RX/

CAP0[0]/

LCDVD[10]/

GPI_23

E17 VDD_IOD I /O HS UART 7 receive

I/O T imer 0 capture input 0

I/O LCD data bit 10 (LPC3230 and LPC3250 only)

I/O General purpose input bit 23

U7_TX/

MAT1[1]/

LCDVD[11]

E18 VDD_IOD O HS UART 7 transmit

O Timer 1 match output 1

O LCD data bit 11 (LPC3230 and LPC3250 only)

USB_ATX_INT C4 VDD_IOC I Interrupt from USB ATX

USB_DAT_VP/

U5_RX D5 VDD_IOC I/O: P USB transmit data, D+ receive

I/O: P UART 5 receive

USB_I2C_SCL E5 VDD_IOC I/O T I2C clock for USB ATX interface

USB_I2C_SDA E6 VDD_IOC I/O T I2C data for USB ATX interface

USB_OE_TP D6 VDD_IOC I/O USB transmit enable for DAT/SE0

USB_SE0_VM/

U5_TX C5 VDD_IOC I/O: P USB single ended zero transmit, D− Receive

I/O: P UART 5 transmit

VDD_AD N12,

N13 VDD_AD power 3.3 V supply for ADC/touch screen

VDD_CORE G7,

G9,

G11,

J7,

J12,

M7,

M11

VDD_CORE power 1.2 V or 0.9 V supply for core

VDD_COREFXD L12,

M13 VDD_COREFXD power Fixed 1.2 V supply for digital portion of the analog

block

VDD_EMC J6,

K6,

K7,

L6,

M6,

M8,

N7,

N8,

N10,

N11

VDD_EMC power 1.8 V or 2.5 V or 3.3 V supply for

External Memory Controller (EMC)

VDD_IOA H13,

J13 VDD_IOA power 1.8 V or 3.3 V supply for IOA domain

VDD_IOB F8 VDD_IOB power 1.8 V or 3.3 V supply for IOB domain

VDD_IOC F7,

G6,

H6, J5

VDD_IOC power 1.8 V or 3.3 V supply for IOC domain

VDD_IOD F13,

F9 VDD_IOD power 1.8 V to 3.3 V sup ply fo r IOD do ma in

VDD_OSC T18 VDD_OSC power 1.2 V supply for main oscillator

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 21 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

[1] The PWM2_CTRL register cont rols this pin function (see LPC32x0 User manual).

VDD_PLL397 T16 VDD_PLL397 power 1.2 V supply for 397x PLL

VDD_PLLHCLK R17 VDD_PLLHCLK power 1.2 V supply for HCLK PLL

VDD_PLLUSB P15 VDD_PLLUSB power 1.2 V supply for USB PLL

VDD_FUSE N14 VDD_FUSE power 1.2 V supply

VDD_RTC K14 VDD_RTC power 1.2 V supply for RTC I/O

VDD_RTCCORE L13 VDD_RTCCORE power 1.2 V supply for RTC

VDD_RTCOSC N15 VDD_RTCOSC power 1.2 V supply for RTC oscillator

VSS_AD P13 - power Ground for ADC/touch screen

VSS_CORE G8,

G10,

G12,

H7,

K12,

L7,

M9,

M10,

M12

- power Ground for core

VSS_EMC K5,

L5,

M5,

N5,

N6,

P6,

P7,

P8,

P9,

P10,

P11

- power Ground for EMC

VSS_IOA K13 - power Ground VDD_IOA domain

VSS_IOB F6 - power Ground VDD_IOB domain

VSS_IOC F5,

G5,

- power Ground VDD_IOC domain

VSS_IOD F10,

F11,

F12,

H12

- power Ground VDD_IOD domain

VSS_OSC P14 - power Ground for main oscillator

VSS_PLL397 T15 - power Ground for 397x PLL

VSS_PLLHCLK R18 - power Ground for HCLK PLL

VSS_PLLUSB R16 - power Ground for USB PLL

VSS_RTCCORE L14 - power Ground for RTC

VSS_RTCOSC P18 - power Ground for RTC oscillator

Table 4. Pin description …continued

Symbol Pin Power supply

domain Type Description

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 22 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

[1] See LPC32x0 User manual for details.

[1] The VDD_IOA, VDD_IOB, VDD_IOC, and VDD_IOD supply domains can be operated at a voltage

independent of the other domains as long as all pins connected to the same peripheral are at the same

voltage level. There are two special cases for determinin g supply domain voltages (for details see

application note AN10777):

a) Ethernet configured in MII mode: VDD_IOD must be the same as VDD_IOB.

b) UART3 when used with hardware flow control or when sharing an RS-232 transceiver with another

UART: VDD_IOA must be the same as VDD_IOD.

Table 5. Digital I/O pad types[1]

Parameter Abbreviation

I/O type I = input.

O = output.

I/O = bidirectional.

I/O T = bidirectional or high impedance.

Pin detail BK: pin has a bus keeper function that weakly re tains the last level

driven on an I/O pin when it is switched from output to input.

PU: pin has a nominal 50 μA inte rnal pull-up connected.

PD: pin has a nominal 50 μA inte rnal pull-down conne cted.

P: pin has programmable input characteristics.

Table 6. Supply domains

Supply domain Voltage range Related supply

pins Description

VDD_CORE 0.9 V to 1.39 V VDD_CORE Core power domain.

VDD_COREFXD 1.2 V VDD_COREFXD Fixed 1.2 V supply for digital portion of

the analog block.

other core

domains 1.2 V VDD_PLL397,

VDD_PLLHCLK,

VDD_PLLUSB,

VDD_FUSE,

VDD_OSC

1.2 V supplies, tied to

VDD_COREFXD.

VDD_RTC 0.9 V to 1.39 V VDD_RTC,

VDD_RTCCORE,

VDD_RTCOSC

RTC supply domain. Can be

connected to a battery backed-up

power source.

VDD_AD 2.7 V to 3.6 V VDD_AD 3.3 V supply for ADC and touch

screen.

VDD_EMC 1.7 V to 1.95 V

2.3 V to 2.7 V

2.7 V to 3.6 V

VDD_EMC External memory interface IO pins in

1.8 V range, 2.5 V range, or 3.3 V

range.

VDD_IOA[1] 1.7 V to 1.95 V or

2.7 V to 3.6 V VDD_IOA Peripheral supply.

VDD_IOB[1] 1.7 V to 1.95 V or

2.7 V to 3.6 V VDD_IOB Peripheral supply.

VDD_IOC[1] 1.7 V to 1.95 V or

2.3 V to 3.6 V VDD_IOC Peripheral supply.

VDD_IOD[1] 1.7 V to 1.95 V or

2.7 V to 3.6 V VDD_IOD Peripheral supply.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 23 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7. Functional description

7.1 CPU and subsystems

7.1.1 CPU

NXP created the LPC3220/30/40/50 using an ARM926EJ-S CPU core that includes a

Harvard architectu re and a 5-st age pipeline. To this ARM core, NXP implemented a 32 kB

instruction cache, a 32 kB data cache and a Vector Floating Point coprocessor. The

ARM926EJ-S core also has an integral Memory Management Unit (MMU) to provide the

virtual memory capabilities required to support the multi-programming demands of

modern operating systems. The basic ARM926EJ-S core V5TE instruction set includes

DSP instruction extensions for native Jazelle Java Byte-code execution in hardware. The

LPC3220/30/40/50 operates at CPU frequencies up to 266 MHz.

7.1.2 Vector Floating Point (VFP) coprocessor

The LPC3220/30/40/50 includes a VFP co-processor providing full support for

single-precision and double-precision add, subtract, multiply, divide, and

multiply-accumulate operations at CPU clock speeds. It is compliant with the IEEE 754

standard for binary Floating-Point Arithmetic. This hardware floating point capability

makes the microcontroller suitable for advanced motor control and DSP applications. The

VFP has 3 separate pipelines for floating-point MAC operations, divide or square root

operations, and Load/Store operations. These pipelines operate in par allel and can

complete execution out of order. All single-precision instructions execute in one cycle,

except the divide and square root instructions. All double-precision multiply and

multiply-accumulate instructions take two cycles. The VFP also provides format

conversions between floating-point and integer word formats.

7.1.3 Emulation and debugging

The LPC3220/30/40/50 supports emulation and debugging via a dedicated JTAG serial

port. An Embedded Trace Buffer allows tracing program execution. The dedicated JTAG

port allows debugging of all chip features without impact to any pins that may be used in

the application .

7.1.3.1 E mb ed d e d ICE

Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of

the target system requires a host computer running the debugger software and an

Embedded ICE prot ocol converter. The Em be dd e d ICE pr ot oc ol con ve rt er con ve rts the

Remote Debug Protocol commands to the JTAG data needed to access the ARM core.

The ARM core has a Debug Communication Channel (DCC) function built-in. The debug

communication channel allows a program running on the target to communicate with the

host debugger or an other sep arate host with out stoppin g the program flow or enter ing the

debug state.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 24 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.1.3.2 E mb ed d e d tra ce bu ff er

The Embedded T race Modu le (ETM) is connected directly to th e ARM core. It compresses

the trace informa tio n an d exports it through a narrow trac e po rt . An inte rn a l Embe d ded

Trace Buffer (ETB) of 2048 ×24 bits captures the trace information under software

debugger control. Data from the ETB is recovered by the debug software through the

JTAG port.

The trace contains information about when the ARM core switches between states.

Instruction shows the flow of execution of the processor and provides a list of all the

instructions that were executed. Instruction trace is significantly compressed by only

broadcasting branch addresses as well as a set of st atus signals tha t indicate the pi peline

status on a cycle by cycle basis. For data accesses either data or address or both can be

traced.

7.2 AHB matrix

The LPC3220/30/40/50 has a multi-layer AHB matrix for inter-block communication. AHB

is an ARM defined high-speed bus, which is part of the ARM bus architecture. AHB is a

high-bandwidth low-latency bus that supports multi-master arbitration and a bus

grant/request mechanism . For systems that have only one (CPU), or two (CPU and DMA)

bus masters a simple AHB works well. However , if a system requires multiple bus masters

and the CPU n eeds access to external memory, a single AHB b us can cause a bottleneck.

To increase performance, the LPC3220/30/40/50 uses an expanded AHB architecture

known as Multi-la yer AHB. A Multi-lay er AHB rep laces the request/ gr ant an d ar bit ra tio n

mechanism used in a simple AHB with an interconnect matrix that moves arbitration out

toward the slave devices. Thus, if a CPU and a DMA controller want access to the same

memory, the interconnect matrix arbitrates between the two when granting access to the

memory. This advanced architecture allows simultane ous access by bus masters to

different resources with an increase in arbitration complexity. In this architectural

implementation, removing guaranteed central arbitration and allowing more than one bus

master to be active at the same time provides better overall microcontroller performance.

In the LPC3220/ 30 /4 0/50 , th e mu lti- La ye r AH B system has a separate bus for each of

seven AHB Masters:

•CPU data bus

•CPU instruction bus

•General purpose DMA Master 0

•General purpose DMA Master 1

•Ethernet controller

•USB controller

•LCD controller

There are no arbitration delays unless two masters attempt to access the same slave at

the same time.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 25 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.2.1 APB

Many peripheral functions are accessed by on-chip APBs that are attached to the higher

speed AHB. The APB performs r eads and writes to peripheral regi sters in three peripheral

clocks.

7.2.2 FAB

Some peripherals are placed on a special bus called FAB that allows faster CPU access

to those peripheral functions. A write access to FAB peripherals takes a single AHB clock

and a read access to FAB peripherals takes two AHB clocks.

7.3 Physical memory map

The physical memory map incorporates several distinct regions, as shown in Figure 3.

When an application is running, the CPU interrupt vectors are re-mapped to allow them to

reside in on-chip SR AM (I RAM ).

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 26 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Fig 3. LPC3220/30/40/50 memory map

on-chip memory

0x4000 0000

0x0000 0000

0.0 GB

768 MB

1.0 GB

4.0 GB

per ipher als on A HB

matrix s lav e por t 5

0 x0FFF FFFF

0x2000 0000

0x3000 0000

0 x2FFF FFFF

0 x1FFF FFFF

0x8000 0000

0 xFFFF FFFF

0x1000 0000

0 x3FFF FFFF

0 x4FFF FFFF

0x5000 0000

0 x7FFF FFFF

per ipher als on A HB

matrix s lav e por t 6

per ipher als on A HB

matrix s lav e por t 7

off-chip memory

IROM or IRAM 0x0000 0000 to 0x03FF FFFF

dummy space for DMA 0x0400 0000 to 0x07FF FFFF

IRAM 0x0800 0000 to 0x0BFF FFFF

IROM 0x0C00 0000 to 0x0FFF FFFF

AHB peripherals 0x2000 0000 to 0x2007 FFFF

AHB peripherals 0x200A 0000 to 0x200B FFFF

APB peripherals 0x2008 0000 to 0x2009 FFFF

RESERVED

AHB peripherals 0x3000 0000 to 0x31FF FFFF

RESERVED

FAB peripherals 0x4000 0000 to 0x4007 FFFF

APB peripherals 0x4008 0000 to 0x400F FFFF

RESERVED

0 x9FFF FFFF

0xA000 0000

0xBFFF FFFF

0xC000 0000

0xDFFF FFFF

0xE000 0000

0xE0FF FFFF

0xE100 0000

0xE1FF FFFF

0xE200 0000

0xE2FF FFFF

0xE300 0000

0xE3FF FFFF

0xE400 0000

2.0 GB EMC_DYSC0

EMC_DYSC1

EMC_CS0

EMC_CS1

EMC_CS2

EMC_CS3

002aae468

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 27 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.4 Internal memory

7.4.1 On-chip ROM

The built-in 16 kB ROM contains a program which runs a boot procedure to load code

from one of four external sources, UART5, SSP0 (SPI mode), EMC Static CS0 memory,

or NAND FLASH.

After reset, execution always begins from the internal ROM. The bootstrap software first

reads the SERVICE input (GPI_1). If SERVICE is LOW , the boot strap start s a service boot

and can download a program over serial link UART5 to IRAM and transfer execution to

the downloaded code.

If the SERVICE pi n is HIGH, the b ootstrap routine jumps to no rma l boot. T he no rmal b oot

process first tests SPI memory for boot information if present it uploads th e boot code and

transfers execution to the uploaded software. If the SPI is not present or no software is

loaded, the bootloader will test the EMC S t atic CS0 memory for the presence of boot code

and if present boots from static memory, If this test fails the boot loader will test external

NAND flash for boot code and boot if code is present.

The boot loader consumes no user memory space because it is in ROM.

7.4.2 On-chip SRAM

On-chip SRAM may be used for code and/or data storage. The SRAM may be accessed

as 8, 16, or 32 bit memory. The LPC3220/30/40/50 provides 256 kB of internal SRAM.

7.5 External memory interfaces

The LPC3220/30/40/50 includes three external memory interfaces, NAND Flash

controllers, Secure Digital Memory Controller, and an external memory controller for

SDRAM, DDR SDRAM, and Static Memory devices.

7.5.1 NAND flash controllers

The LPC3220/30/40/50 includes two NAND flash controllers, one for multi-level cell

NAND flash devices and one for single-level cell NAND flash devices. The two NAND

flash controllers use the same pins to interface to external NAND flash devices, so only

one interface is active at a time.

7.5.1.1 Multi-Level Cell (MLC) NAND flash controller

The MLC NAND flash controller interfaces to either multi-level or single-level NAND flash

devices. An external NAND flash device is used to allow the bootloader to automatically

load a portion of the application code into internal SRAM for execution following reset.

The MLC NAND flash controller supports small (528 byte) and large (2114 byte) pages.

Programmable NAND timing parameters allow support for a variety of NAND flash

devices. A built-in Reed-Solomon encoder/decoder provides error detection and

correction capability. A 528 byte data buffer reduces the need for CPU supervision during

loading. The MLC NAND flash controller also provides DMA support.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 28 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.5.1.2 Single-Level Cell (SLC) NAND flash controller

The SLC NAND flash controller interfaces to single-level NAND flash devices. DMA page

transfers are supported, including a 20-byte DM A read and write FIF O. Hardware support

for ECC (Error Checking and Correction) is includ ed for the main dat a area. Software can

correct a single bit error.

7.5.2 SD card controller

The SD interface allows access to external SD memory cards. The SD card interface

conforms to the SD Memory Card Specification Version 1.01.

7.5.2.1 Features

•1-bit and 4-bit data line interface support.

•DMA is supported through the system DMA controller.

•Provides all functions specific to the SD memory card. These include the clock

generation unit, power management control, command and data transfer.

7.5.3 External memory controller

The LPC3220/30/40/50 includes a memory controller that supports data bus SDRAM,

DDR SDRAM, and static memory devices. The memory controller pr ov ide s an inte rfa ce

between the system bus and external (off-chip) memory devices.

The controller supports 16-bit and 32-bit wide SDR SDRAM devices of 64 Mbit, 128 Mbit,

128 Mbit, 256 Mbit, and 512 Mbit sizes, as well as 16-bit wide data bus DDR SDRAM

devices of 64 Mbit, 128 Mbit, 128 Mbit, 256 Mbit, and 512 Mbit sizes. Two dynamic

memory chip selects are supplied, supporting two groups of SDRAM:

•DYCS0 in the address range 0x8000 0000 to 0x9FFF FFFF

•DYCS1 in the address range 0xA000 0000 to 0xBFFF FFFF

The memory controller also supports 8-bit, 16-bit, and 32-bit wide asynchronous static

memory devices, including RAM, ROM, and flash, with or without asynchronous page

mode. Four static memory chip selects are supplied f or SRAM devices:

•CS0 in the address range 0xE000 0000 to 0xE0FF FFFF

•CS1 in the address range 0xE100 0000 to 0xE1FF FFFF

•CS2 in the address range 0xE200 0000 to 0xE2FF FFFF

•CS3 in the address range 0xE300 0000 to 0xE3FF FFFF

The SDRAM controller uses three data ports to allow simultaneous requests from multiple

on-chip AHB bus masters and has the following features.

•Dynamic memory interface supports SDRAM, DDR-SDRAM, and low-power variants.

•Read and write buffers to reduce latency and improve performance.

•Static memory features include

–asynchronous page mode read

–programmable wait states

–bus turnaround cycles

–output enable and write enable delays

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 29 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

–extended wait

•Power-saving modes dynamically control EMC_CKE[1:0] and EMC_CLK.

•Dynamic memory self-refresh mode supported by software.

•Controller support s 2 k, 4 k, and 8 k row address synchr onous me mory parts. That is,

typical 512 MB, 256 MB, 128 MB, and 16 MB parts, with 8, 16, or 32 data bits per

device.

•Two reset domains enable dynamic memory contents to be preserved over a soft

reset.

•This controller does not support synchronous static memory devices (burst mode

devices).

7.6 AHB master peripherals

The LPC3220/30/40/50 implements four AHB master peripherals, which include a

General Purpose Dire ct Memory Access (GPDMA) controller, a 10/100 Ethernet Media

Access Controller (MAC), a Universal Serial Bus (USB) controller, and an LCD controller.

Each of these four per ipherals cont ain an integral DMA contr oller optimized to su pport the

performance demands of the peripheral.

7.6.1 General Purpose DMA (GPDMA) controller

The GPDMA controller allows peripheral-to memory, memory-to-peripher al,

peripheral- to -p erip he ra l, an d m em o ry- to -me mo ry transactions. Eac h DM A stre am

provides unidirectional serial DMA transfers for a single source and destination. For

example, a bidirectional port requires one stream for transmit and one for receive. The

source and destination areas can each be either a memory region or a peripheral, and

can be accessed through the same AHB master, or one area by each master. The DMA

controller supports the following peripheral device transfers.

•Secure Digital (SD) Memory interface

•High-speed UARTs

•I2S0 and I2S1 ports

•SPI1 and SPI2 interfaces

•SSP0 and SSP1 interfaces

•Memory

The DMA controls eight DMA channels with hardware prioritization. The DMA controller

interfaces to the syst em via two AHB bus ma st er s, ea ch with a full 32 -b it da ta bus width.

DMA operations may be set up for 8-bit, 16-bit, and 32-bit data widths, and can be either

big-endian or little-endian. Incrementing or non-incrementing addressing for source and

destination are supported, as well as programmable DMA burst size. Scatter or gather

DMA is supported through the use of linked lists. This means that the source and

destination ar ea s do not hav e to oc cu py contiguous areas of mem o ry.

7.6.2 Ethernet MAC

The Ethernet block contains a full featured 10 Mbit/s or 100 Mbit/s Ethernet MAC

designed to provide optimized performance through the use of DMA hardware

acceleration. Features include a generous suite of control registers, half or full duplex

operation, flow control, control frames, hardware acceleration for transmit retry, receive

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 30 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

packet filtering an d wa ke-u p on LAN activity. Automatic frame transmissio n and recep tion

with scatter-gather DMA of f-load s many operation s from the CPU. The Ethernet DMA can

access off-chip memory via the EMC, as well as the IRAM. The Ethernet block interfaces

between an off-chip Ethernet PHY using the Media Independent Interface (MII) or

Reduced MII (RMII) protocol and the on-chip Media Independent Interface Management

(MIIM) serial bus.

7.6.2.1 Features

•Ethernet standards support:

–Supports 10 Mbit/s or 100 Mbit/s PHY devices including 10 Base-T, 100 Base-TX,

100 Base-FX, and 100 Base-T4.

–Fully compliant with IEEE standard 802.3.

–Fully compliant with 802.3x Full Duplex Flow Control and Half Duplex back

pressure.

–Flexible transmit and receive frame options.

–Virtual Local Area Network (VLAN) frame support.

•Memory management:

–Independent transmit and receive buffers memory mapped to SRAM.

–DMA managers with scatter/gather DMA and arrays of frame descriptors.

–Memory traffic optimized by buffering and pre-fetching.

•Enhanced Ethernet features:

–Receive filtering.

–Multicast and broadcast frame support for both transmit and receive.

–Optional automatic Frame Check Sequence (FCS) insertion with Circular

Redundancy Check (CRC) for transmit.

–Selectable automatic transmit frame padding.

–Over-length frame support for both transmit and receive allows any length frames.

–Promiscuous receive mode.

–Automatic collision back-off and frame retransmission.

–Includes power management by clock switching. Wake-on-LAN power

management support allows system wake-up using the receive filters or a magic

frame detection filter.

•Physical interface

–Attachment of external PHY chip through standard MII or RMII interface.

–PHY register access is available via the MIIM interface.

7.6.3 USB interface

The LPC3220/30/40/50 supports USB in either device, host, or OTG configuration.

7.6.3.1 USB device controller

The USB device controller enables 12 Mbit/s da t a exchang e with a USB host controlle r. It

consists of register interface, serial interface engine, endpoint buffer memory and DMA

controller. The serial interface engine deco des the USB data str eam and writes dat a to the

appropriate end point buffer memory. The status of a completed USB tra nsfer or error

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 31 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

condition is indicated via status registers. An interrupt is also generated if enabled. The

DMA controller when enabled transfers data between the endpoint buffer and the USB

RAM.

Features

•Fully compliant with USB 2.0 full-speed specification.

•Supports 32 physical (16 logical) endpoints.

•Supports control, bulk, interrupt and isochronous endpoints.

•Scalable realization of endpoints at run time.

•Endpoint maximum packet size selection (up to USB maximum specification) by

software at run time.

•RAM message buffer size based on endpoint realization and maximum packet size.

•Supports bus-powered capability with low suspend current.

•Supports DMA transfer on all non-control endpoints.

•One duplex DMA channel serves all endpoints.

•Allows dynamic switching between CPU controlled and DMA modes.

•Double buffer implementation for bulk and isochronous endpoints.

7.6.3.2 USB host controller

The host controller enab les dat a exchange with variou s USB devices att ached to the bu s.

It consists of register interface, serial interface engine and DMA controller. The register

interface complies to the OHCI specification.

Features

•OHCI compliant.

•OHCI specifies the op e ra tio n an d int er fa ce of the USB host controller and software

driver.

•The host controller has four USB states visible to the software driver:

–USBOperational: Process lists and generate SOF tokens.

–USBReset: Forces reset signaling on the bus, SOF disabled.

–USBSuspend: Monitor USB for wake-up activity.

–USBResume: Forces resume signaling on the bus.

•HCCA register points to interrupt and isochronous descriptors list.

•ControlHead ED an d Bulk He ad ED re gis ter s point to control and bulk descriptors list.

7.6.3.3 USB OTG controller

USB OTG (On-The-Go) is a supplement to the USB 2.0 specification that augments the

capability of existing mobile devices and USB peripherals by adding host functionality for

connection to USB peripherals.

Features

•Fully compliant with On-The-Go supplement to the USB Specification 2.0 Revision

1.0.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 32 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

•Supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP) for

dual-role devices under software control. HNP is partially imple m en te d in ha rdwa re .

•Provides programmable timers required for HNP and SRP.

•Supports slave mode oper ation through AHB slav e inte rf ac e.

•Supports the OTG ATX from NXP (ISP 1302) or any external CEA-2011OTG

specification compliant ATX.

7.6.4 LCD controller

The LCD controller provides all of the necessary control signals to interface directly to a

variety of color and mono chro me LCD panels. Both STN (single and dua l panel) and TFT

panels can be oper ated. The disp lay resolu tion is se lect able a nd can be up to 1024 ×768

pixels. Several color modes are provided, up to a 24-bit true-color non-palettized mode.

An on-chip 512-byte color palette allows reducing bus utilization (i.e. memory size of the

displayed data) while still supporting a large number of colors.

The LCD interface includes its own DMA controller to allow it to operate independently of

the CPU and other sys te m fu nc tion s. A built-in FIFO acts as a buffer for display data,

providing flexibility for system timing. Hardware cursor support can further reduce the

amount of CPU time needed to operate the display.

7.6.4.1 Features

•AHB bus master interface to access frame buffer.

•Setup and control via a separate AHB slave interface.

•Dual 16-deep programmable 64-bit wide FIFOs for buffering incoming display data.

•Supports single and dual-panel monochrome Super Twisted Nematic (STN) displays

with 4-bit or 8-bit interfaces.

•Supports single and dual-panel color STN displays.

•Supports Thin Film Transistor (TFT) color displays.

•Programmable display resolution including, but not limited to: 320 × 200, 320 × 240,

640 × 200, 640 × 240, 640 × 480, 800 × 600, and 1024 × 768.

•Hardware cursor support for single-panel displays.

•15 gray-level monochrome, 3375 color STN, and 32 k color palettized TFT support.

•1, 2, or 4 bits-per-pixel (bpp) palettized displays for monochrome STN.

•1, 2, 4, or 8 bpp palettized color displays for color STN and TFT.

•16 bpp true-color non-palettized, for color STN and TFT.

•24 bpp true-color non-palettized, for color TFT.

•Programmable timing for different display panels.

•256 entry, 16-bit palette RAM, arranged as a 12 8 × 32 bit RAM.

•Frame, line, and pix el cloc k s ign als .

•AC bias signal for STN, data enable signal for TFT panels.

•Supports little and big-endian, and Windows CE data formats.

•LCD panel clock may be generated from the pe ripheral clock or from a clock input pin.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 33 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.7 System functions

To enhance the performance of the LPC3220/30/40/50 incorporates the following system

functions, an Interrupt Controller (INTC), a watchdog timer, a millisecond timer, and

several power control features. These functions are described in the following sections

7.7.1 Interrupt controller

The interrupt contr oller is comprised of three basic in terrupt controller blocks, supp orting a

total of 73 interrupt sources. Each interrupt source can be individually enabled/disabled

and configured for high or low level triggering, or rising or falling edge triggering. Each

interrupt may also be steered to either the FIQ or IRQ input of the ARM9. Raw interrupt

status and masked interrupt status registers allow versatile condition evaluation. In

addition to peripheral functions, each of the six general purpose input/output pins and

12 of the 22 general purpose input pins are connected directly to the interrupt controller.

7.7.2 Watchdog timer

The watchdog timer block is clocked by the main peripheral clock, which clocks a 32-bit

counter. A match register is compared to the Timer. When configured for watchdog

functionality, a match drives the match output low. The match output is gated with an

enable signal that give s the op portunity to gener ate two type of r eset signal: one that only

resets chip internally, and another that goes through a programmable pulse generator

before it goes to the external pin RESOUT and to the internal chip reset.

7.7.2.1 Features

•Programmable 32-bit timer.

•Internally resets the device if not periodically reloaded.

•Flag to indicate that a watchdog reset has occurred.

•Programmable watchdog pulse output on RESOUT pin.

•Can be used as a standard timer if watchdog is not used.

•Pause control to stop counting when core is in debug state.

7.7.3 Millisecond timer

The millisecond timer is clocked by 32 kHz RTC clock, so a prescaler is not needed to

obtain a lower count rate.

The millisecond timer includes three match registers that are compared to the

T imer/Cou nter value. A match can generate an interrupt and the cause the Timer/Counter

either continue to run, stop, or be reset.

7.7.3.1 Features

•32-bit Timer/Counter, running from the 32 kHz RTC clock.

•Counter or Timer operation.

•Three 32-bit match registers that allow:

–Continuous operation with optional interrupt generation on match.

–Stop timer on match with optional interrupt generation.

–Reset timer on match with optional interrupt generation.

•Pause control to stop counting when core is in debug state.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 34 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.7.4 Clocking and power control features

7.7.4.1 Clocking

Clocking in the LPC3220/30/40/50 is designed to be versatile, so that system and

peripheral requirements may be met, while allowing optimization of power consumption.

Clocks to most functions may be turned off if not needed and some peripherals do this

automatically.

The LPC3220/30/40/50 supports three operational modes, two of which are specifically

designed to reduce po wer consumption. The mode s are: Run mode, Direct run mod e, and

S t op mode.These three oper ational modes give control over processin g speed and power

consumption. In addition, clock rates to different functional blocks may be changed by

switching clock sources, changing PLL values, or altering clock divider configurations.

This allows a trade-off of power versus processing speed based on application

requirements.

7.7.4.2 Crystal oscillator

The main oscillator is the basis for the clocks most chip functions use by default.

Optionally, many functions can be clocked instead by the output of a PLL (with a fixed

397x rate multiplication) which runs from the RTC oscillator. In this mode, the main

oscillator may be turned off unless the USB interface is enabled. If a SYSCLK frequency

other than 13 MHz is required in the application, or if the USB block is not used, the main

oscillator may be used with a frequency of between 1 MHz and 20 MHz.

7.7.4.3 PLLs

The LPC3220/30/40/50 includes three PLLs: The 397x PLL allows boosting the RTC

frequency to 13.008896 MHz for use as the prima ry system clock. The USB PLL provides

the 48 MHz clock required by the USB block, and the HCLK PL L provides the basis for the

CPU clock, the AHB bus clock, an d th e ma in per iph er al clo ck.

The 397x PLL multiplies the 32768 Hz RTC clock by 397 to obtain a 13.008896 MHz

clock. The 397x PLL is designed for low power operation and low jitter. This PLL requires

an external RC loop filter for proper operation.

The HCLK PLL accepts an input clock from either the main oscillator or the output of the

397x PLL. The USB PLL only accepts an input clock from the main oscillator.The USB

input clock runs through a divide-by-N pre-divider before entering the USB PLL.

The input to the HCL K and USB PLLs may init ially be divided down by a pre-divider value

‘N’, which may have the values 1, 2, 3, or 4. This pre-divider can allow a greater number of

possibilities for the output frequency. Following the PLL input divider is the PLL multiplier.

This can multiply the pre-divider output by a value ‘M’, in the range of 1 through 256. The

resulting frequency must be in the range of 156 MHz to 320 MHz. The multiplier works by

dividing the output of a Current Controlled Oscillator (CCO) by the value of M, then using

a phase detector to compare the divided CCO output to the pre-divider output. The error

value is used to adjust the CCO frequency.

At the PLL output, there is a post-divider that can be used to bring the CCO frequency

down to the desired PLL output frequency. The post-divider value can divide the CCO

output by 1, 2, 4, 8, or 16. The post-divider can also be bypassed, allowing the PLL CCO

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 35 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

output to be used directly. The maximum PLL output frequency supported by the CPU is

266 MHz. The only outp ut frequ ency sup ported by the USB PLL is 48 MHz, and the clock

has strict requirements for nominal frequency (500 ppm) and jitter (500 ps).

7.7.4.4 Power control modes

The LPC3220/30/40/50 supports three operational modes, two of which are specifically

designed to reduce power consumption. The modes are: Run mode, Direct Run mode,

and Stop mode.

Run mode is the normal operating mode for applications that req uire th e CP U, AHB bu s,

or any peripheral function other than the USB block to run faster than the main oscillator

frequency. In Run mode, the CPU can run at up to 266 MHz and the AHB bus can run at

up to 133 MHz.

Direct Run mode allows reducing the CPU and AHB bus rates in order to save power.

Direct Run mode can also be the normal operating mode for applications that do not

require the CPU, AHB bus, or any peripheral function other than the USB block to run

faster than the main oscillator frequency. Direct Run mode is the default mode following

chip reset.

Stop mode causes all CPU and AHB operation to cease, and stops clocks to peripherals

other than the USB block.

7.7.4.5 Reset

Reset is accomplished by an active LOW signal on the RESET input pin. A reset pulse

with a minimum width of 10 main oscillator clocks after the oscillator is stable is required to

guarantee a valid chip reset. At power-up, 10 milliseconds should be allowed for the

oscillator to start up and stabilize after VDD reaches operational volt age. An internal reset

with a minimum duration of 10 clock pulses will also be applied if the watchdog timer

generates an internal device reset.

The RESET pin is located in the RTC power domain. This means that the RTC power

must be present for an external reset to have any effect. The RTC power domain

nominally runs from 1.2 V, but the RESET pin can be driven as high as 1.95 V.

7.8 Communication peripheral interfaces

In addition to the Ethernet MAC and USB interfaces there are many more serial

communication peripheral interfaces available on the LPC3220/30/40/50. Here is a list of

the serial communication interfaces:

•Seven UARTs; four standard UARTs and three high-speed UARTs

•Two SPI serial I/O controllers

•Two SSP serial I/O controllers

•Two I2C serial I/O controllers

•Two I2S audio controllers

A short functional description of each of these peripherals is provided in the following

sections.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 36 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.8.1 UARTs

The LPC3220/30/40/50 contains seven UARTs. Four are standard UARTs, and three are

high-speed UARTs.

7.8.1.1 Standard UARTs

The four standard UARTs are compatible with the INS1 6Cx50. These UARTs support

rates up to 460800 bit/s from a 13 MHz peripheral clock.

Features

•Each standard UART has 64 byte Receive and Transmit FIFOs.

•Receiver FIFO trigger points at 16, 32 , 48 , and 60 Bytes.

•Transmitter FIFO trigger points at 0, 4 , 8, and 16 Bytes.

•Register locations conform to the “550” industry standard.

•Each standard UART has a fractional rate pre-divider and an internal baud rate

generator.

•The standard UARTs support three clocking modes: on, off, and auto-clock. The

auto-clock mode shuts off the clock to the UART when it is idle.

•UART 6 includes an IrDA mode to support infrared communication.

•The standard UARTs are designed to support data rates of (2400, 4800, 9600,

19200, 38400, 57600, 115200, 230400, 460800) bit/s.

•Each UART includes an internal loopback mode.

7.8.1.2 High-speed UARTs

The three high-speed UARTs are designed to support rates up to 921600 bit/s from a

13 MHz peripheral clock for on-board communication in low noise conditions. This is

accomplished by changing the over sampling from 16× to 14× and altering the rate

generation logic.

Features

•Each high-speed UART has 64-byte Receive and Transmit FIFOs.

•Receiver FIFO trigger points at 1, 4, 8, 16, 32, and 48 B.

•Transmitter FIFO trigger points at 0, 4, and 8 B.

•Each high-speed UART has an internal baud rate generator.

•The high-speed UARTs are designed to support data rates of (2400, 4800, 9600,

19200, 38400, 57600, 115200 , 230400, 460800, 921600) bit/s.

•The three high speed UARTs only support (8N1) 8-bit d ata word length, 1-stop bit, no

parity, and no flow control as a the communications protocol.

•Each UART includes an internal loopback mode.

7.8.2 SPI serial I/O controller

The LPC3220/30/40/50 has two Serial Peripheral Interfaces (SPI). The SPI is a 3-wire

serial interface that is able to interface with a large range of serial peripheral or memory

devices (SPI mode 0 to 3 compatible slave devices).

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 37 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Only a single master and a single slave can communicate on the interface during a given

data transfer. During a data transfer the master always sends a byte of data to the slave,

and the slave always sends a byte of data to the master. The SPI implementation on the

LPC3220/30/40/50 does not support operation as a slave.

7.8.2.1 Features

•Supports slaves compatible with SPI mo d es 0 to 3.

•Half duplex synchronous transfers.

•DMA support for data transmit and receive.

•1-bit to 16-bit word length.

•Choice of LSB or MSB first data transmission.

•64 ×16-bit input or output FIFO.

•Bit rates up to 52 Mbit/s.

•Busy input function.

•DMA time out interrupt to allow detection of end of reception when using DMA.

•Timed interrupt to facilitate emptying the FIFO at the end of a transmission.

•SPI clock and data pins may be used as general purpose pins if the SPI is not used.

•Slave selects can be supported using GPO or GPIO pins

7.8.3 SSP serial I/O controller

The LPC3220/30/40/50 contains two SSP controllers. The SSP controller is capable of

operation on a SPI, 4-wir e SSI, or Microwire bus. It can interact with multiple masters and

slaves on the bus. Only a single master and a single slave can communicate on the bus

during a given data transfer. The SSP supports full duplex transfers, with frames of 4 bits

to 16 bits of data flowing from the master to th e slave and from th e slave to th e master. In

practice, often only one of these data flows carries meaningful data.

7.8.3.1 Features

•Compatible with Motorola SPI, 4-wire TI SSI, and National Semiconductor Microwire

buses

•Synchronous serial communication

•Master or slave operation

•8-frame FIFOs for both transmit and receive

•4-bit to 16-bit frame

•Maximum SPI bus dat a bit r ate of 1⁄2 (Master mode) and 1⁄12 (Slave mode) of the input

clock rate

•DMA transfers supp or te d by GPDM A

7.8.4 I2C-bus serial I/O controller

There are two I2C-bus interfaces in the LPC32x0 family of controllers. These I2C blocks

can be configured as a master, multi-master or slave supporting up to 400 kHz. The I2C

blocks also support 7 or 10 bit addressing. Each has a four word FIFO for both transmit

and receive. An interrupt signal is available from each block.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 38 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

There is a separate slave transmit FIFO. The slave transmit FIFO (TXS) and its level are

only available when the controlle r is configured as a Master/Slave device and is operating

in a multi-master environm ent. Sep arate TX FIFOs are ne eded in a multi- master beca use

a controller might have a message queued for transmission when an external master

addresses it to be come a slave-transmitter, a second source of data is needed.

Note that the I2C clock must be enabled in the I2CCLK_CTRL register before using the

I2C. The I2C clock can be disabled between communications, if used as a single master

I2C-bus interface, software has full control of when I2C communication is taking place on

the bus.

7.8.4.1 Features

•The two I2C-bus blo cks are standard I2C- bus compliant interfaces that may be used in

Single-master, Multi-master or Slave modes.

•Programmable clock to allow adjustment of I2C-bus transfer rates.

•Bidirectional data transfer.

•Serial clock synchronization allows devices with different bit rates to communicate via

one serial bus.

•Serial clock synchronization can be used as a handshake mech anism to suspend and

resume serial transfer.

7.8.5 I2S-bus audio controller

The I2S-bus provides a standard communication interface for digital audio applications

The I2S-bus specification defines a 3-wire serial bus using one data line, one clock line,

and one word select signal. Each I2S connection can act as a master or a slave. The

master connection determines the frequency of the clock line and all other slaves are

driven by this cloc k source. The two I2S-bus interfaces o n the LPC3220/30/40/50 provides

a separate transmit and receive channel, providing a total of two transmit channels and

two receive channels. Each I2S channel supports monaural or stereo formatted data.

7.8.5.1 Features

•The interface has sep arate input/output channels each of which can o perate in master

or slave mode.

•Capable of handling 8-bit, 16-bit, and 32-bit word sizes.

•Mono and stereo audio data supported.

•Supports standard sampling frequ e nc ies (8 kHz, 11.025 kHz, 16 kHz, 22 .0 5 kHz,

32 kHz, 44.1 kHz, 48 kHz, 96 kHz).

•Word select period can be configured in master mode (separately for I2S input and

output).

•Two eight-word FIFO data buffers are provided, one for transmit and one for receive.

•Generates interrupt requests when buffer levels cross a programmable boundary.

•Two DMA requests, controlled by programmable buffer levels. These are connected

to the GPDMA block.

•Controls include reset, stop, and mute options separately for I2S input and I2S output.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 39 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.9 Other peripherals

In addition to the communica tio n p eriphe ral s there ar e m any gene ra l pu rpose p er iphe ra ls

available in the LPC3220/30/40/50. Here is a list of the general purpose peripherals.

•GPI/O

•Keyboard scanner

•Touch screen controller and 10-bit Analog-to-Digital-Converter

•Real-time clock

•High-speed timer

•Four general pu rp os e 32 -b it tim er /ex te rn al even t co un te rs

•Two simple PWMs

•One motor control PWM

A short functional description of each of these peripherals is provided in the following

sections.

7.9.1 General purpose parallel I/O

Some device pins that are not dedicated to a specific peripheral function have been

designed to be general purpo se inp ut s, output s, or input/ou tput s. Also, some pins may be

configured either as a specific peripheral function or a general purpose input, output, or

input/output. A total of 51 pins can potentially be used as general purpose input/outputs,

24 as general purpose outputs, and 22 as general purpose inputs.

GPIO pins may be dynamically configured as inputs or outputs. Separate registers allow

setting or clearing any number of GPIO and GPO outputs controlled by that register

simultaneously. The value of the output register for standard GPIOs and GPO pins may

be read back, as well as the current actual state of the port pins.

In addition to GPIO pins on port 0, port 1, and port 2, there are 22 GPI, 24 GPO, and

six GPIO pins. When the SDRAM bus is configured for 16 data bits, 13 of the remaining

SDRAM data pins may be used as GP IOs .

7.9.1.1 Features

•Bit-level set and clear r egisters allow a single instruction set or clear of any num ber of

bits in one port.

•A single register selects direction for pins that support both input and output modes.

•Direction control of individual bits.

•For input/output pins, both the programmed output state and the actual pin state can

be read.

•There are a total of 12 general purpose inputs, 24 general purpose outputs, and six

general purpose input/outputs.

•Additionally, 13 SDRAM data lines may be used as GPIOs if a 16-bit SDRAM

interface is used (rather than a 32-bit interface).

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 40 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

7.9.2 Keyboard scanner

The keyboard scanner function can automatically sc an a keyboard of up to 64 keys in an

8×8 matrix. In operation, the keyboard scanner’s internal state machine will normally be

in an idle state, with all KEY_ROWn pins set high, waiting for a change in the column

inputs to indicate that one or more keys have been pressed.

When a keypress is detected, the matrix is scanned by setting one output pin high at a

time and reading the column inputs. After de-bouncing, the keypad state is stored and an

interrupt is generated. The keypad is then continuously scanned waiting for ‘extra key

pressed’ or ‘key released’. Any new keypad state is scanned and stored into the matrix

registers followed by a new interrupt request to the interrupt controller. It is possible to

detect and separate up to 64 multiple keys pressed.

7.9.2.1 Features

•Supports up to 64 keys in 8 ×8 matrix.

•Programmable de-bounce period.

•A key press can wake up the CPU from Stop mode.

7.9.3 Touch screen controller and 10-bit ADC

The LPC3220/30/40/50 microcontrollers includes Touch Screen Controller (TSC)

hardware, which automatically measures and determines the X and Y coordinates where

a touch screen is pressed. In addition, the TSC can measure an analog input signal on the

AUX_IN pin.

Optionally, the TSC can operate as an Analog-to-Digital Converter (ADC). The ADC

supports three channels and uses 10-bit successive ap proximation to produce results with

a resolution of 10 bits in 11 clock cycles.

The analog portion of the ADC has its own power supply to enhance the low noise

characteristics of the converte r. This voltage is only supplied inte rn ally wh en the co re has

voltage. However, the ADC block is not affected by any difference in ramp-up time for

VDD_AD and VDD_CORE voltage supplies.

7.9.3.1 Features

•Measuremen t ra ng e of 0 V to VDD_ AD (n om in ally 3. 3 V).

•Low-noise ADC.

•10-bit resolution.

•Three input channels.

•Uses 32 kHz RTC clock or peripheral clock.

7.9.4 Real-Time Clock (RTC) and battery RAM

The RTC runs at 32768 Hz using a very low power oscillator. The RTC counts seconds

and can gen erate alarm interrupt s that can wa ke up the d evice from Stop mode. The RTC

clock can also clock the 397x PLL, the Millisecond T imer, the ADC, the Keyboard Scanner

and the PWMs. The R TC up-counter value repre sents a number of seconds elap sed since

second 0, which is an application determined time. The RT C counter will reach maximum

value after about 136 year s. The RTC down-cou nt er is initiat ed with all on es .

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 41 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Two 32-bit match registers are readable and writable by the processor . A match will result

in an interrupt provided that the interrupt is enabled. The ONSW output pin can also be

triggered by a match event and cause an external power supply to turn on all of the

operating voltages, as a way to startup after power has been removed.

The RTC block is implemented in a separate voltage domain. The block is supplied via a

separate supply pin from a batt er y or ot he r po we r sou rc e.

The RTC block also cont ains 32 words (128 bytes) of very low voltage SRAM. This SRAM

is able to hold its contents down to the minimum RTC operating voltage.

7.9.4.1 Features

•Measures the passage of time in seconds.

•32-bit up and down seco nd s coun te rs.

•Ultra-low power design to support battery powered systems.

•Dedicated 32 kHz oscillator.

•An output pin is included to assist in waking up when the chip has had power removed

to all functions except the RTC.

•Two 32-bit matc h re gis ter s with inte rru p t op tion .

•32 words (128 bytes) of very low voltage SRAM.

•The R TC and b atte ry RAM power ha ve an inde pe ndent po we r dom ain and ded icated

supply pins, which can be pow er ed fro m a batt ery or po we r su pp ly.

Remark: The LPC3220/30/40/50 will run at voltages down to 0.9 V at frequencies below

14 MHz. However , the ARM core cannot access the RTC registers and battery RAM when

the core supply voltage is at 0.9 V and the RTC supply is at 1.2 V.

7.9.5 Enhanced 32-bit timers/external event counters

The LPC3220/30/40/50 includes six 32-bit Timer/Counters. The Timer/Counter is

designed to count cycles of the system derived clock or an externally-sup plied clock. It

can optionally generate interrupts or perform other actions at specified timer values,

based on four match reg isters. The T imer/Counter also include s four capture inputs to trap

the timer value when an input signal transitions, optionally generating an interrupt.

7.9.5.1 Features

•A 32-bit Timer/Counter with a programmable 32-bit pre-scaler.

•Counter or Timer operation.

•Up to four 32-bit capture channels per timer, that can take a snapshot of the timer

value when an input signal transitions. A capture event may also optionally generate

an interrupt.

•Four 32-bit matc h re gist er s tha t allo w:

–continuous operation with optional interrupt generation on match

–stop timer on match with optional interrupt generation

–reset timer on match with optional interrupt generation

•Up to four external outputs corresponding to match registers, with the following

capabilities:

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 42 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

–set LOW on match

–set HIGH on match

–toggle on match

–do nothing on match

7.9.6 High-speed timer

The high-speed timer block is clocked by the main peripheral clock. The clock is first

divided down in a 16-bit programmable pre-scale counter which clocks a 32-bit

timer/counter.

The high-speed timer includes three match registers that are compared to the

timer/counter value. A match can generate an interrupt and cause the timer/counter to

either continue to run, stop, or be reset. The high-speed timer also includes two capture

registers that can take a snapshot of the timer/counter value when an input signal

transitions. A capture event may also generate an interrupt.

7.9.6.1 Features

•32-bit timer/cou nt er with pr og ra m m abl e 16 -b it pr e- scale r.

•Counter or timer op er a tion .

•Two 32-bit captu r e regist er s.

•Three 32-bit match registers that allow:

–Continuous operation with optional interrupt generation on match.

–Stop timer on match with optional interrupt generation.

–Reset timer on match with optional interrupt generation.

•Pause control to stop counting when core is in debug state.

7.9.7 Pulse Width Modulators (PWMs)

The LPC3220/3 0/40/50 provides two simple PWMs . They are clocked separately by either

the main peripheral clock or the 32 kHz RTC clock. Both PWMs have a duty cycle

programmable in 255 steps.

7.9.7.1 Features

•Clocked by the main peripheral clock or the 32 kHz RTC clock.

•Programmable 4-bit pre-scaler.

•Duty cycle programmable in 255 steps.

•Output frequency up to 50 kHz when using a 13 MHz peripheral clock.

7.9.8 Motor control pulse width modulator

The Motor Control PWM (MCPWM) provides a set of features for three-phase AC and DC

motor control applications in a single peripheral. The MCPWM can also be configured for

use in other gene r alize d timin g, coun ting, capture, and compare applications.

7.9.8.1 Features

•32-bit timer

•32-bit period register

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 43 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

•32-bit pulse-width (match) register

•10-bit dead-tim e re gis te r an d an a ssociated 10-bit dead-time counter

•32-bit capture re gister

•Two PWM (match) outputs (pins MCOA0/1/2 and MCOB0/1/2) with opposite polarities

•Period interrupt, pulse-width interrupt, and capture interrupt

8. Basic architecture

The LPC3220/30/40/50 is a general purpose ARM926EJ-S 32-bit microprocessor with a

32 kB instruction cache and a 32 kB data cache. The microcontroller offers high

performance and very low power consumption. The ARM architecture is based on RISC

principles, which results in the instruction se t and re lated deco de mech anism being much

simpler than equivalent micro programmed CISCs. This simplicity results in a high

instruction throughput and impressive real-time interrupt response from a small and

cost-effective processor core.

The ARM926EJ-S core employs a 5-stage pipeline so processing and memory system

accesses can occur continuously. At any one point in time, several operations are in

progress: subsequent instruction fetch, next instruction decode, instruction execution,

memory access, and write-back. The combination of architectural enhancements gives

the ARM9 about 30 % better performance than an ARM7 running at the same clock rate:

•Approximately 1.3 clocks per instruction for the ARM926 compared to 1.9 clocks per

instruction for ARM7TDMI.

•Approximately 1.1 Dhrystone MIPS/MHz for the ARM926 compared to 0.9 Dhrystone

MIPS/MHz for ARM7TDMI.

The ARM926EJ-S processor also employs an operational state known as Thumb, which

makes it ideally suited to high-volume applications with memory restrictions, or

applications where code density is an issue.

The key idea behind Thumb state is the use of a super-reduced instruction set.

Essentially, the ARM926EJ-S processor core has two instruction sets:

1. The standard 32-bit ARM set

2. The 16-bit Thumb set

The Thumb set’ s smaller 16- bit instruction length allows it to approach twice the density of

standard ARM code while retaining many of ARM’s 32-bit performance advantage over a

traditional 16-bit processor using 16-bit registers. This is possible because Thumb code

operates using the same 3 2-bit reg ister set as ARM code. Thumb code size is up to 65 %

smaller than ARM code size, and 160 % of the performance of an equivalent ARM

processor connected to a 16-bit memory system. Additionally, the ARM926EJ-S core

includes enhanced DSP instructions and multiplier, as well as an enhanced 32-bit MAC

block.

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  44 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
9. Limiting values
 
[1] The following applies to Table 7:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive 
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated 
maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless 
otherwise noted.
[2] Core, PLL, oscillator, and RTC supplies; applies to pins VDD_CORE, VDD_COREFXD, VDD_OSC, VDD_PLL397, VDD_PLLHCLK, 
VDD_PLLUSB, VDD_RTC, VDD_RTCCORE, and VDD_RTCOSC.
[3] I/O pad supply; applies to domains VDD_EMC.
[4] Applies to VDD_AD pins.
[5] Applies to pins in the following domains VDD_IOA, VDD_IOB, VDD_IOC, and VDD_IOD.
[6] Including voltage on outputs in 3-state mode.
[7] Based on package heat transfer, not device power consumption. Calculated package thermal resistance (ThetaJA): 35.766 °C/W (with 
JEDEC Test Board and 0 m/s airflow, ±15 % accuracy).
[8] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
[9] Charge device model per AEC-Q100-011.
Table 7. L imiting  values
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol Parameter Conditions Notes Min Max Unit
VDD(1V2) supp ly voltage (1.2 V) [2] −0.5 +1.4 V
VDD(EMC) external memory controller 
supply voltage [3] −0.5 +4.6 V
VDDA(3V3) analog supply voltage (3.3 V) [4] −0.5 +4.6 V
VDD(IO) input/output supply voltage [5] −0.5 +4.6 V
VIA analog input voltage −0.5 +4.6 V
VIinput voltage 1.8 V pins [6] −0.5 +2.4 V
3.3 V pins [6] −0.5 +4.6 V
IDD supply current per supply pin - 100 mA
ISS ground current per ground pin - 100 mA
Tstg storage temperature −65 +150 °C
Ptot(pack) total power dissipation 
(per package) max. junction temp 125 °C
max. ambient temp 85 °C[7] -1.12W
VESD electrostatic discharge voltage HBM [8] - 2500 V
CDM [9] - 1000 V

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  45 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
10. Static characteristics
 
Table 8. Static characteristics
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typ[1] Max Unit
VDD(1V2) supply voltage (1.2 V) core supply voltage for 
full performance; 
266 MHz (see Figure 4); 
VDD_CORE supply domain
[2] 1.31 1.35 1.39 V
core supply voltage for 
normal performance; 
208 MHz (see Figure 4);
VDD_CORE supply domain
[2] 1.1 1.2 1.39 V
core supply voltage for 
reduced power; 
up to 14 MHz CPU;
VDD_CORE supply domain
[2] 0.9 - 1.39 V
RTC supply voltage;
VDD_RTC supply domain [3] 0.9 - 1.39 V
PLL and oscillator supply 
voltage [4] 1.1 1.2 1.39 V
VDD(EMC) external memory 
controller supply voltage  in 1.8 V range [5] 1.7 1.8 1.95 V
in 2.5 V range [6] 2.3 2.5 2.7 V
in 3.3 V range [7] 2.7 3.3 3.6 V
VDD(IO) input/output supply 
voltage VDD_IOA, VDD_IOB, and 
VDD_IOD supply domain
in 1.8 V range
1.7 1.8 1.95 V
in 3.3 V range 2.7 3.3 3.6 V
VDD_IOC supply domain
in 1.8 V range 1.7 1.8 1.95 V
in 3.3 V range 2.3 3.3 3.6 V
VDDA(3V3) analog supply voltage
(3.3 V) applies to pins in VDD_AD 
power domain 2.7 3.3 3.6 V

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 46 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Power consumption in Run, direct Run, and Stop modes

IDD(run) Run mode supply

current Tamb =25°C;

code

while(1){}

executed from IRAM; all

peripherals enabled

I-cache/D-cache, MMU

enabled; CPU

clock = 208 MHz;

VDD_CORE = 1.2 V

- 150 - mA

I-cache/D-cache, MMU

enabled; CPU

clock = 266 MHz;

VDD_CORE = 1.35 V

- 218 - mA

I-cache/D-cache, MMU

disabled; CPU

clock = 208 MHz;

VDD_CORE = 1.2 V

-78-mA

I-cache/D-cache, MMU

disabled; CPU

clock = 266 MHz;

VDD_CORE = 1.35 V

- 111 - mA

IDD(drun) direct Run mode supply

current Tamb =25°C; CPU

clock = 13 MHz;

code

while(1){}

executed from IRAM; all

peripherals disabled

I-cache/D-cache, MMU

enabled;

VDD_CORE = 1.2 V

-7.8-mA

I-cache/D-cache, MMU

enabled;

VDD_CORE = 0.9 V

-5.6-mA

I-cache/D-cache, MMU

disabled;

VDD_CORE = 1.2 V

-5-mA

I-cache/D-cache, MMU

disabled;

VDD_CORE = 0.9 V

-3.5-mA

IDD(stop) Stop mode supply

current Tamb =25°C; CPU

clock stopped internally; all

peripherals disabled

VDD_CORE = 1.2 V - 400 - μA

VDD_CORE = 0.9 V - 400 - μA

Table 8. Static characteristics …continued

Tamb =

−

C to +85

C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  47 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
IDD(RTC) RTC supply current VDD_RTC = 
VDD_RTCCORE = 
VDD_RTCOSC = 1.2 V;
Tamb =25°C
-13-μA
Input pins and I/O pins configured as input
VIinput voltage [8][10] 0-V
DD(IO) V
VIH HIGH-level 
input voltage 1.8 V inputs 0.7 × VDD(IO) -- V
3.3 V inputs 0.7 × VDD(IO) -- V
VIL LOW-level 
input voltage 1.8 V inputs - - 0.3 × VDD(IO) V
3.3 V inputs - - 0.3 × VDD(IO) V
Vhys hysteresis voltage 1.8 V inputs 0.1 × VDD(IO) -- V
3.3 V inputs 0.1 × VDD(IO) -- V
IIL LOW-level
input current VI = 0 V; no pull-up - - 1 μA
IIH HIGH-level 
input current VI = VDD(IO); no pull-down [8] --1μA
Ilatch I/O latch-up curre n t −(1.5VDD(IO)) < VI < 
(1.5VDD(IO))[8] --100mA
Ipu pull-up current 1.8 V inputs with pull-up; 
VI = 0 V 61222μA
3.3 V inputs with pull-up; 
VI = 0 V 25 50 80 μA
Ipd pull-down current 1.8 V inputs with pull-down; 
VI = VDD(IO)
51222μA
3.3 V inputs with pull-down; 
VI = VDD(IO)
25 50 85 μA
Ciinput capacitance Excluding bonding  
pad cap acitance --3.3pF
Output pins and I/O pins configured as output
VOoutput voltage [8][9]
[10][11] 0-V
DD(IO) V
VOH HIGH-level output 
voltage 1.8 V outputs; IOH = −1 mA [12] VDD(IO) − 0.4 - - V
3.3 V outputs; IOH = −4 mA [12] VDD(IO) − 0.4 - - V
VOL LOW-level 
output voltage 1.8 V outputs; IOL = 4 mA [12] --0.4V
3.3 V outputs; IOL = 4 mA [12] --0.4V
IOH HIGH-level 
output current  VDD(IO) = 1.8 V; 
VOH = VDD(IO) − 0.4 V [8][12] −3.3 - - mA
VDD(IO) = 3.3 V; 
VOH = VDD(IO) − 0.4 V −6.5 - - mA
IOL LOW-level 
output current  VDD(IO) = 1.8 V; VOL = 0.4 V [8][12] 1.5 - - mA
VDD(IO) = 3.3 V; VOL = 0.4 V 3 - - mA
IOZ OFF-state 
output current VO = 0 V; VO=V
DD(IO);
no pull-up/down [8] --1μA
Table 8. Static characteristics …continued
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typ[1] Max Unit

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  48 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
IOHS HIGH-level short-circuit 
output current  VDD(IO) = 1.8 V; VOH = 0 V [13] --66mA
VDD(IO) = 3.3 V; VOH = 0 V - - 183 mA
IOLS LOW-level short-circuit 
output current  VDD(IO) = 1.8 V; VOL = 
VDD(IO)
[8][13] --34mA
VDD(IO) = 3.3 V; VOL = 
VDD(IO)
--105mA
Zooutput impedance VDD(IO) = 1.8 V 40 - 60 Ω
VDD(IO) = 3.3 V 40 - 60 Ω
EMC pins
VIinput voltage [10] 0-V
DD(EMC) V
VIH HIGH-level input voltage 1.8 V inputs 0.7 × VDD(EMC) -- V
3.3 V inputs 0.7 × VDD(EMC) -- V
VIL LOW-level input voltage 1.8 V inputs - - 0.3 × VDD(EMC) V
3.3 V inputs - - 0.3 × VDD(EMC) V
Vhys hysteresis voltage 1.8 V inputs 0.4 - 0.6 V
3.3 V inputs 0.55 - 0.85 V
IIL LOW-level 
input current VI = 0 V; no pull-up - - 0.3 μA
IIH HIGH-level
input current VI = VDD(EMC); no pull-down - - 0.3 μA
Ilatch I/O latch-up curre n t −(1.5VDD(EMC)) < VI < 
(1.5VDD(EMC))--100mA
Ipu pull-up current 1.8 V inputs with pull-up; 
VI = 0 34 62 107 μA
3.3 V inputs with pull-up; 
VI = 0 97 169 271 μA
Ipd pull-down current 1.8 V inputs with pull-down; 
VI = VDD(EMC)
23 51 93 μA
3.3 V inputs with pull-down; 
VI = VDD(EMC)
73 155 266 μA
Ciinput capacitance Excluding bonding
pad cap acitance --2.1pF
VOoutput voltage [9]
[10][11] 0-V
DD(EMC) V
VOH HIGH-level 
output voltage 1.8 V outputs; IOH = −1 mA [12] VDD(EMC) − 0.3 - - V
3.3 V outputs; IOH = −4 mA [12] VDD(EMC) − 0.3 - - V
VOL LOW-level 
output voltage 1.8 V outputs; IOL = 4 mA [12] --0.3V
3.3 V outputs; IOL = 4 mA [12] --0.3V
IOH HIGH-level 
output current  VDD(EMC) = 1.8 V; 
VOH = VDD(EMC) − 0.4 V [12] −6-- mA
VDD(EMC) = 3.3 V; 
VOH = VDD(EMC) − 0.4 V −6-- mA
Table 8. Static characteristics …continued
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typ[1] Max Unit

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  49 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
IOL LOW-level 
output current  VDD(EMC) = 1.8 V; 
VOL = 0.4 V [12] 6--mA
VDD(EMC) = 3.3 V; 
VOL = 0.4 V 6--mA
IOZ OFF-state 
output current VO = 0 V; VO=V
DD(EMC);
no pull-up/down --0.3μA
IOHS HIGH-level short-circuit 
output current  VDD(EMC) = 1.8 V; VOH = 0 V [13] --−49 mA
VDD(EMC) = 3.3 V; VOH = 0 V - - −81 mA
IOLS LOW-level short-circuit 
output current  VDD(EMC) = 1.8 V; 
VOL = VDD(EMC)
[12] --49mA
VDD(EMC) = 3.3 V; 
VOL = VDD(EMC)
--86mA
Zooutput impedance VDD(EMC) = 1.8 V 35 40 58 Ω
VDD(EMC) = 3.3 V 32 35 45 Ω
I2C pins
VIinput voltage [8]
[10] 0 - 5.5V V
VIH HIGH-level 
input voltage 1.8 V inputs 0.7 × VDD(IO) -- V
3.3 V inputs 0.7 × VDD(IO) -- V
VIL LOW-level 
input voltage 1.8 V inputs - - 0.3 × VDD(IO) V
3.3 V inputs - - 0.3 × VDD(IO) V
IIL LOW-level 
input current VI = 0 V; no pull-up - - 10 μA
IIH HIGH-level 
input current VI = VDD(IO); no pull-down [8] --10μA
Ilatch I/O latch-up curre n t −(1.5VDD(IO)) < VI < 
(1.5VDD(IO))[8] --100mA
Ciinput capacitance Excluding bonding 
pad cap acitance --1.6pF
VOL LOW-level 
output voltage 1.8 V outputs; IOL = 4 mA [12] --0.4V
3.3 V outputs; IOL = 4 mA [12] --0.4V
IOL LOW-level 
output current  VDD(IO) = 1.8 V; VOL = 0.4 V [8][12] 3--mA
VDD(IO) = 3.3 V; VOL = 0.4 V 3 - - mA
IOZ OFF-state 
output current VO = 0 V; VO=V
DD(IO);
no pull-up/down [8] --10μA
IOLS LOW-level short-circuit 
output current  VDD(IO) = 1.8 V; VOL = 
VDD(IO)
[8][13] --40mA
VDD(IO) = 3.3 V; VOL = 
VDD(IO)
--40mA
ONSW pin
VOoutput voltage [8][9]
[10][11] 0-V
DD(1V2) V
VOH HIGH-level 
output voltage 1.2 V outputs; IOH = −1 mA [12] VDD(1V2) − 0.4 - - V
Table 8. Static characteristics …continued
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typ[1] Max Unit

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  50 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
[1] Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages.
[2] Applies to VDD_CORE pins.
[3] Applies to pins VDD_RTC, VDD_RTCCORE, and VDD_RTCOSC.
[4] Applies to pins VDD_COREFXD, VDD_OSC, VDD_PLL397, VDD_PLLHCLK, and VDD_PLLUSB.
[5] Applies when using 1.8 V Mobile DDR or Mobile SDR SDRAM.
[6] Applies when using 2.5 V DDR memory.
[7] Applies when using 3.3 V SDR SDRAM and SRAM.
[8] Referenced to the applicable VDD for the pin.
[9] Including voltage on outputs in 3-state mode.
[10] The applicable VDD voltage for the pin must be present.
[11] 3-state outputs go into 3-state mode when the applicable VDD voltage for the pin is grounded.
[12] Accounts for 100 mV voltage drop in all supply lines.
[13] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
VOL LOW-level 
output voltage 1.2 V outputs; IOL = 4 mA [12] --0.4V
IOH HIGH-level 
output current  VOH = VDD(1V2) − 0.4 V [8][12] −4-- mA
IOL LOW-level 
output current  VOL = 0.4 V [8][12] 3--mA
IOZ OFF-state 
output current VO = 0 V; VO=V
DD(1V2);
no pull-up/down [8] --1.5μA
IOHS HIGH-level short-circuit 
output current  VDD(1V2) = 1.8 V; VOH = 0 V [13] --−135 mA
IOLS LOW-level short-circuit 
output current  VOL = VDD(1V2) [8][13] --135mA
Zooutput impedance VDD(1V2) = 1.2 V 40 - 60 Ω
Oscillator input/output pins 
Vi(xtal) crystal input voltage on pins RTCX_IN and 
SYSX_IN −0.5 - +1.3 V
Vo(xtal) crystal output voltage on pins RTCX_OUT and 
SYSX_OUT −0.5 - +1.3 V
Reset pin
VIinput voltage [8]
[10] 0 - 1.95 V
VIH HIGH-level input voltage 1.2 V inputs 0.7 × VDD(1V2) -- V
VIL LOW-level input voltage 1.2 V inputs - - 0.3 × VDD(1V2) V
IIL LOW-level input current VI = 0 V; no pull-up - - 1 μA
IIH HIGH-level input current VI = VDD; no pull-down [8] --1μA
IOZ OFF-state output current VO = 0 V; VO=V
DD; 
no pull-up/down [8] --1μA
Ilatch I/O latch-up curre n t −(1.5VDD) < VI < (1.5VDD)[8] --100mA
Table 8. Static characteristics …continued
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typ[1] Max Unit

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 51 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

10.1 Minimum core voltage requirements

Figure 4 shows the minimum core supply voltage that should be applied for a given core

frequency on pin VDD_ CORE to ensure stable operatio n of th e LPC32 20 /3 0 /40/ 50 .

10.2 Power supply sequencing

The LPC32x0 has no p ower sequencing require ments, that is, VDD(1V2), VDD(EMC), VDD(IO),

and VDDA(3V3) can be switched on or off independen t of each other. An internal circuit

ensures that the system correctly powers up in the absence of core power. During IO

power-up this circuit takes care that the system is powered in a defined mode. The same

is valid for core power-down.

10.3 Power consumption per peripheral

[1] All three Ethernet clocks are in enabled in the MAC_CLK_CTRL register (see LPC32x0 User manual).

Fig 4. Minimum required core supply voltage for different core frequencies

core frequency (MHz)

160 280240200

002aae872

1.0

1.2

1.4

0.8

VDD_CORE

(V)

Table 9. Power consumpt ion per peripheral

Tamb =25

C; CPU clock = 208 MHz; I-cache/D-cache, MMU disa bled; VDD_CORE = 1.2 V;

VDD(IO) = 1.8 V; USB AHB, IRAM, and IROM clocks always on; all peripherals are at their default

state at reset. Peripheral clocks are disabled except for peripheral measured.

Peripheral IDD(run) / mA

High-speed UART (set to 115 200 Bd (8N1)) 0.3

I2C-bus 0.3

SSP 0.6

I2S0.5

DMA 6.3

EMC 7.3

Multi-level NAND controller 1.4

Single-level NAND controller 0.3

LCD 5.6

Ethernet MAC[1] 2.9

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 52 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

10.4 Power consumption in Run mode

Power consumption is shown in Figure 5 for WinCE applications running under typical

conditions from SDRAM. MMU and I-cache/D-cache are enabled. The VFP is turned on

but not used. I2S-interface (channel 1), LCD, SLC NAND controller, I2C1-bus, SD card,

touchscreen ADC, and UART3 are turned on. All other peripherals are turned off.

The AHB clock HCLK is identical to the core clock for fre quencies up to 133 MHz, which is

the maximum allowed HCLK frequency. For higher core frequencies, the HCLK PLL

output must be divided by 2 to obtain an HCLK frequency lower th an or equ al to 133 MHz

resulting in correspondingly lower power consumption by the AHB periphe ra ls.

Conditions: Tamb =25°C; VDD_CORE = 1.2 V for core frequencies ≤ 208 MHz;

VDD_CORE = 1.35 V for core frequencies > 208 MHz; VDD(IO) = 1.8 V.

(1) WinCE running from SDRAM; playing wmv file at 20 frames/s, 32 kHz mono.

(2) WinCE running from SDRAM; playing mp3 file at 128 kbit/s, stereo.

(3) WinCE running from SDRAM; no application running.

Fig 5. Core current versus co re frequency for WinCE applications

core frequency (MHz)

40 280200120

002aae762

120

160

IDD(run)

(mA)

(1)

(2)

(3)

HCLK = 133 MHz

HCLK = 72 MHz

VDD_CORE =

1.2 V VDD_CORE =

1.35 V

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  53 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
10.5 ADC static characteristics
 
[1] Conditions: VSSA = 0 V (on pin VSS_AD); VDDA(3V3) = 3.3 V (on pin VDD_AD).
[2] The ADC is monotonic; there are no missing codes.
[3] The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 6.
[4] The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after 
appropriate adjustment of gain and offset errors. See Figure 6.
[5] The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the 
ideal curve. See Figure 6.
[6] The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset 
error, and the straight line which fits the ideal transfer curve. See Figure 6.
[7] The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated 
ADC and the ideal transfer curve. See Figure 6.
Table 10 . ADC static characteristics
VDDA(3V3) =3.3V; T
amb =25
°
C unless otherwise specified; ADC clock frequency 4.5 MHz. 
Symbol Parameter Conditions Min Typ Max Unit
VIA analog input voltage 0 - VDDA(3V3) V
Cia analog input capacitance - - 1 pF
EDdifferential linearity error [1][2][3] -±0.5 ±1LSB
EL(adj) integral non-linearity [1][4] -±0.6 ±1LSB
EOoffset error [1][5] -±1±3LSB
EGgain error [1][6] -±0.3 ±0.6 %
ETabsolute er ror [1][7] -±4LSB
Rvsi voltage source interface resistance - - 40 kΩ

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 54 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

(1) Example of an actual transfer curve.

(2) The ideal transfer curve.

(3) Differential linearity error (ED).

(4) Integral non-linearity (EL(adj)).

(5) Center of a step of the actual transfer curve.

Fig 6. ADC characteristics

002aae434

1023

1022

1021

1020

1019

(2)

(1)

10241018 1019 1020 1021 1022 1023

7123456

1018

(5)

(4)

(3)

1 LSB

(ideal)

code

out

VDDA(3V3) − VSSA

1024

offset

error

gain

error

offset error

VIA (LSBideal)

1 LSB =

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  55 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
11. Dynamic characteristics
11.1 Clocking and I/O port pins
 
[1] Parameters are valid over operating temperature range unless otherwise specified.
[2] After supply voltages are stable
[3] Supplied by an external crystal.
11.2 Static memory controller
 
Table 11. Dynamic char acteristics
Tamb =
−
40
°
C to +85
°
C, unless otherwise specified.[1]
Symbol Parameter Conditions Min Typ Max Unit
Reset
tw(RESET)ext external RESET pulse width [2] 10 - - ms
External clock
fext external clock frequency [3] 11320MHz
Port pins
trrise time - 5 - ns
tffall time - 5 - ns
Table 12. Dynam ic characteristics: static external memory interface
CL=25pF, T
amb =20
°
C, VDD(EMC) = 1.8 V, 2.5 V, or 3.3 V.
Symbol Parameter Notes Min Typ Max Unit
Common to read and write cycles
TCLCL clock cycle time  [1] 7.5 9.6 - ns
tCSLAV CS LOW to address valid time - 0 - ns
Read cycle parameters
tOELAV OE LOW to address valid time [2] -0−WAITOEN ×TCLCL -ns
tBLSLAV BLS LOW to address valid time [2] -0−WAITOEN ×TCLCL -ns
tCSLOEL CS LOW to OE LOW time - 0 + WAITOEN ×TCLCL -ns
tCSLBLSL CS LOW to BLS LOW time [2] - 0 + WAITOEN ×TCLCL -ns
tOELOEH OE LOW to OE HIGH time [2][3] -(WAITRD−WAITOEN + 1) ×TCLCL -ns
tBLSLBLSH BLS LOW to BLS HIGH time [2][3] -(WAITRD−WAITOEN + 1) ×TCLCL -ns
tsu(DQ) data input/output set-up time [6] -8.4 -ns
th(DQ) data input/output hold time [6] -0 -ns
tCSHOEH CS HIGH to OE HIGH time - 0 - ns
tCSHBLSH CS HIGH to BLS HIGH time - 0 - ns
tOEHANV OE HIGH to address invalid time - 1 ×TCLCL -ns
tBLSHANV BLS HIGH to address invalid time - 1 ×TCLCL -ns
Write cycle parameters
tCSLDV CS LOW to data valid time - 0 - ns
tCSLWEL CS LOW to WE LOW time [4] -(WAITWEN+1)×TCLCL -ns
tCSLBLSL CS LOW to BLS LOW time [4] -(WAITWEN+ 1) ×TCLCL -ns
tWELDV WE LOW to data valid time [4] -0−(WAITWEN + 1) ×TCLCL -ns

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 56 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

[1] TCLCL = 1/HCLK

[2] Refer to the LPC32x0 user manual EMCStaticWaitOen0-3 register for the programming of WAITOEN value.

[3] Refer to the LPC32x0 user manual EMCStaticWaitRd0-3 register for the programming of WAITRD value.

[4] Refer to the LPC32x0 user manual EMCStaticWaitWen0-3 register for the programming of WAITWEN value.

[5] Refer to the LPC32x0 user manual EMCStaticWaitWr0-3 register for the programming of WAITWR value.

[6] Earliest of CS HIGH, OE HIGH, address change to data invalid.

tWELWEH WE LOW to WE HIGH time [4][5] -(WAITWR−WAITWEN + 1) ×TCLCL -ns

tBLSLBLSH BLS LOW to BLS HIGH time [4][5] -(WAITWR−WAITWEN + 1) ×TCLCL -ns

tWEHANV WE HIGH to address invalid time - 1 ×TCLCL -ns

tWEHDNV WE HIGH to data invalid time - 1 ×TCLCL -ns

tBLSHANV BLS HIGH to address invalid time - 1 ×TCLCL -ns

tBLSHDNV BLS HIGH to data invalid time - 1 ×TCLCL -ns

Table 12. Dynam ic characteristics: static external memory interface …continued

CL=25pF, T

amb =20

C, VDD(EMC) = 1.8 V, 2.5 V, or 3.3 V.

Symbol Parameter Notes Min Typ Max Unit

Fig 7. External memory read access

EMC_CS[3:0]

EMC_A[23:0]

EMC_D[31:0]

EMC_OE

EMC_BLS[3:0]

tCSLAV

tOELAV

tOELOEH

tCSLOEL

tsu(DQ) th(DQ)

tCSHOEH

tOEHANV

002aae402

tBLSLAV tCSHBLSH

tBLSLBLSH

tCSLBLSL tBLSHANV

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 57 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Fig 8. External memory write access

EMC_A[23:0]

EMC_D[31:0]

tCSLWEL

tCSLBLSL

tWELDV

tCSLDV

tWELWEH

tWEHANV

tBLSHANV

tWEHDNV

tBLSHDNV

002aae469

tCSLAV

EMC_CS[3:0]

tBLSLBLSH

EMC_BLS[3:0]

EMC_WR

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 58 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

11.3 SDR SDRAM Controller

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical values valid for EMC pads set to fast slew rate: VDD_EMC = 1.8 V, VDD_CORE = 1.2 V or slower slew rate: VDD_EMC = 3.3 V,

VDD_CORE = 1.2 V (see SDRAMCLK_CTRL register in the LPC32x0 User manual).

[3] All min or max values valid for EMC pads set to fast slew rate: VDD_EMC = 1.8 V, VDD_CORE = 1.2 V or slower slew rate: VDD_EMC

= 3.3 V, VDD_CORE = 1.2 V.

[4] foper = 1/tCK.

[5] Applies to signals: EMC_DQM[3:0], EMC_DYCSm, EMC_RAS, EMC_CAS, EMC_WR, EMC_CKEm.

[6] CMD_DLY = COMMAND_DELAY bitfield in SDRAMCLK_CTRL[18:14] register, see External memory controller (EMC) chapter in

LPC32x0 User manual.

Table 13. EMC SDR SDRAM memor y interface dynamic characteristics

CL=25pF, T

amb =

−

C to +85

C, unless otherwise specified.[1][3]

Symbol Parameter Min Typical[2] Max Unit

foper operating frequency [4] 104 133 MHz

tCK clock cycle time 7.5 9.6 - ns

tCL CK LOW-level width - 4.8 - ns

tCH CK HIGH-level width - 4.8 - ns

td(V)ctrl control valid delay time [5][6] - (CMD_DLY × 0.25) + 2.7 ns

th(ctrl) cont rol ho l d ti me [5][6] (CMD_DLY × 0.25) + 1.2 - ns

td(AV) address valid delay time [6] - (CMD_DLY × 0.25) + 3.2 ns

th(A) address hold time [6] (CMD_DLY × 0.25) + 1.2 - ns

td(QV) data output valid delay time [6] - (CMD_DLY × 0.25) + 3.5 ns

th(Q) data output hold time [6] (CMD_DLY × 0.25) + 1.2 - ns

tsu(D) data input set-up time - 0.6 - ns

th(D) data input hold time - 0.9 - ns

tQZ data output high-impedance time - - < tCK ns

Fig 9. SDR SDRAM signal timing

002aae420

EMC_CLK

output signal (O)

input signal (I)

td(V)ctrl, td(AV), td(QV) th(ctrl), th(Q), th(A)

th(D)

tsu(D)

tCK

tCL

tCH

tQZ

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  59 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
11.4 DDR SDRAM controller
 
[1] All values valid for EMC pads set to fast slew rate at 1.8 V unless otherwise specified (see SDRAMCLK_CTRL register in the LPC32x0 
User manual).
[2] CMD_DLY = COMMAND_DELAY bitfield in SDRAMCLK_CTRL[18:14] register, see External memory controller (EMC) chapter in 
LPC32x0 User manual.
[3] Applies to signals EMC_DQM[1:0], EMC_DYCSm, EMC_RAS, EMC_CAS, EMC_WR, EMC_CKEm.
[4] DQS_DELAY, see LPC32x0 user manual, External Memory Controller Chapter, Section 8 DDR DQS delay calibration for details on 
configuring this value.
[5] Test conditions for measurements: Tamb = −40 °C to +85 °C; operating frequency range foper = 52 MHz to 133 MHz; EMC_DQMm and 
EMC_D[31:0] driving 2 inches of 50 Ω characteristic impedance trace with 10 pf capacitive load; no external source series termination  
resistors used. EMC pads set to fast slew rate at 1.8 V or 2.5 V (see SDRAMCLK_CTRL register in the LPC32x0 User manual).
Table 14. EMC DDR SDRAM memory interface dynamic characteristics[1]
CL=25pF, T
amb =25
°
C, unless otherwise specified.
Symbol Parameter Conditions Min Typical Max Unit
foper operating frequency - 104 133 MHz
tCK clock cycle time  7.5 9.6  - n s
tCL CK LOW-level width - 0.5 × tCK -ns
tCH CK HIGH-level width - 0.5 × tCK -ns
td(V)ctrl control valid delay time [2][3] - (CMD_DLY × 0.25) + 1.5 - ns
th(ctrl) control hold time [2][3] - (CMD_DLY × 0.25) − 1.5 - ns
td(AV) address valid delay time [2] - (CMD_DLY × 0.25) + 1.5 - ns
th(A) address hold time [2] - (CMD_DLY × 0.25) − 1.5 - ns
tsu(Q)  d ata output set-up time EMC_D and 
EMC_DQM to 
EMC_DQS 
out
[5] 0.08 × 
tCK
0.15 × tCK 0.25 
× tCK
ns
th(Q)  data output hold time EMC_D and 
EMC_DQM to 
EMC_DQS 
out
[5] 0.25 × 
tCK
0.35 × tCK 0.42 
× tCK
ns
tDQSH DQS HIGH time for WRITE 
command -0.5 × tCK -ns
tDQSL DQS LOW time for WRITE 
command -0.5 × tCK -ns
tDQSS WRITE command to first DQS latching 
transition ti me fo r DQS out - tCK + 0.7 - ns
tDSS DQS falling edge to CK set-up ti me fo r DQS in - 0.5 × tCK -ns
tDSH DQS falling edge hold time from CK for DQS in - 0.5 × tCK -ns
td(DQS) DQS delay time for DQS in [4] -DQS_DELAY -ns
tsu(D) data input set-up time - 0.3 - ns
th(D) data input hold time - 0.5 - ns

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 60 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Fig 10. DDR control timing parameters

EMC_CLK

EMC control

and address

signals

002aae436

tCK tCH tCL

td(AV); td(V)ctrl th(A); th(ctl)

valid

Fig 11. DDR write timing p a rameters

command

EMC_D[15:0],

EMC_DQM[1:0]

DQSL

DQSH

DQSS

h(Q)

EMC_DQS[1:0]

EMC_CLK

002aae437

WRITE

su(Q)

DSH

DSS

(1) The delay of the EMC_DQSm signal is determined by the DQS_DELAY settings. See LPC32x0 user manual, External Memory

Controller Chapter, section DDR DQS delay calibration for details on configuring this value.

Fig 12. DDR read timing parameters

EMC_CLK

command

EMC_D[31:0]

tsu(D)

EMC_DQSm

002aae438

th(D)

READ

delayed EMC_DQSm(1)

td(DQS)

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 61 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

11.5 USB controller

[1] Parameters are valid over operating temperature range unless otherwise specified.

11.6 Secure Digital (SD) card interface

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages.

Table 15. Dynamic characteristics USB digital I/O pins

VDD(IO) = 3.3 V; Tamb =

−

C to +85

C, unless otherwise specified.[1]

Symbol Parameter Conditions Min Typ Max Unit

tTIO bus turnaround time (I/O) OE_N/INT_N to DAT/VP and SE0/VM - 7 - ns

tTOI bus turnaround time (O/I) OE_N/INT_N to DAT/VP and SE0/VM - 0 - n s

Fig 13. USB bus turnaround time

002aae440

USB_DAT_VP

tTIO tTOI

USB_OE_TP

USB_SE0_VM

input output input

Table 16. Dynam ic characteristics: SD card pin interf ace

Tamb =

−

C to +85

C for industrial applications; VDD(IO) over specifi e d rang e s.[1]

Symbol Parameter Conditions Min Typ[2] Max Unit

Tcy(clk) clock cycle time on pin MS_SCLK; Data transfer mode - - 25 MHz

on pin MS_SCLK; Identification mode - - 400 kHz

tsu(D) data input set-up time on pins MS_BS, MS_DIO[3:0] as inputs - 2.7 - ns

th(D) data input hold time on pins MS_BS, MS_DIO[3:0] as inputs - 0 - ns

td(QV) data output valid delay time on pins MS_BS, MS_DIO[3:0] as outputs - 9.7 - ns

th(Q) data output hold time on pins MS_BS, MS_DIO[3:0] as outputs - 7.7 - ns

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  62 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
 
11.7 MLC NAND flash memory controller
 
[1] THCLK = 1/HCLK
[2] CEAD = bitfield TCEA_DELAY[1:0] in register MLC_TIME_REG[25:24]
[3] WL = bitfield WR_LOW[3:0] in register MLC_TIME_REG[3:0] 
[4] WH = bitfield WR_HIGH[3:0] in register MLC_TIME_REG[7:4] 
[5] RL = bitfield RD_LOW[3:0] in register MLC_TIME_REG[11:8]
[6] RH = bitfield RD_HIGH [3:0] in register MLC_TIME_REG[15:12]
[7] RHZ = bitfield NAND_TA[2:0] in register MLC_TIME_REG[18:16]
[8] BD = bitfield BUSY_DELAY[4:0] in register MLC_TIME_REG[23:19]
Fig 14.  SD card pin interfa ce t imin g
002aae441
MS_SCLK
MS_DIO[3:0](O)
MS_DIO[3:0] (I)
td(QV)
th(D)
tsu(D)
Tcy(clk)
th(Q)
MS_BS (O)
MS_BS (I)
Table 17. Dynamic characteristics of the MLC NAND flash memory controller
Tamb =
−
40
°
C to +85
°
C.
Symbol Parameter  Min Typ Max Unit
tCELREL CE LOW to RE LOW time [1][2] -T
HCLK × CEAD-ns
tRC RE cycle time [1][5][6] -T
HCLK × (RL + 1) + THCLK × (RH − RL)- ns
tREH RE HIGH hold time [1][5][6] -T
HCLK × (RH − RL)-ns
tRHZ RE HIGH to output high-impedance time [1][5][7] -T
HCLK × (RH − RL) + THCLK × RHZ -ns
tRP RE pulse width [1][5] -T
HCLK × (RL + 1) - ns
tREHRBL RE HIGH to R/B LOW time [1][8] -T
HCLK × BD -ns
tWB WE HIGH to R/B LOW time [1][8] -T
HCLK × BD -ns
tWC WE cycle time [1][3][4] -T
HCLK × (WL + 1) + THCLK × (WH − WL)- ns
tWH WE HIGH hold time [1][3][4] -T
HCLK × (WH − WL)-ns
tWP WE pulse width [1][3] -T
HCLK × (WL + 1) - ns

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 63 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

11.8 SLC NAND flash memory controller

Fig 15. MLC NAND flash controller write timing (writing to NAND flash)

Fig 16. MLC NAND flash controller read timing (reading from NAND flash)

FLASH_IO[7:0]

FLASH_WR

FLASH_RDY (R/B)

FLASH_CE

D0 D1 Dn 10h

002aae442

FLASH_IO[7:0]

tRP tREH

tRC

FLASH_RD

FLASH_CE

tCELREL

D0 D1 D2 D3

tRHZ

002aae443

Table 18. Dynamic characteristics of SLC NAND flash memory controller

Tamb =

−

C to +85

Symbol Parameter Conditions Min Typ Max Unit

tALS ALE set-up time re ad [1][2][4][6] -T

HCLK × (Rsu + Rw) - ns

write - THCLK × (Wsu + Ww) - ns

tALH ALE hold time read [1][7] -T

HCLK × Rh - ns

write - THCLK × Wh - ns

tAR ALE to RE delay time read [1][2][6] -T

HCLK × Rsu - ns

write - THCLK × Wsu - ns

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  64 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
tCEA CE access time read [1][2][4][6][8] -T
HCLK × (Rsu + Rw) - ns
write - THCLK × (Wsu + Ww) - ns
tCS CE set-up time read [1][2][4][6][8] -T
HCLK × (Rsu + Rw) - ns
write - THCLK × (Wsu + Ww) - ns
tCH CE hold time read [1][3] -T
HCLK × Rh - ns
write - THCLK × Wh - ns
tCLS CLE set-up time read [1][2][4][6][8] -T
HCLK × (Rsu + Rw) - ns
write - THCLK × (Wsu + Ww) - ns
tCLH CLE hold time read [1][3] -T
HCLK × Rh - ns
write - THCLK × Wh - ns
tCLR CLE to RE delay time read [1][2][6] -T
HCLK × Rsu - ns
write - THCLK × Wsu - ns
tDH data ho l d  time   output from  
NAND 
controller; read
[1][3][7] -T
HCLK × Rh - ns
output from 
NAND 
controller; 
write 
-T
HCLK × Wh - ns
tDS data set-up time  output from 
NAND 
controller; read
[1][2][4][6][8] -T
HCLK × (Rsu + Rw)  - ns
output from 
NAND 
controller; 
write 
-T
HCLK × (Wsu + Ww) -
tIR output high-impedance to RE 
LOW time read [1][2][6] -T
HCLK × Rsu - ns
write - THCLK × Wsu - ns
tRC RE cycle time read [1][2] -T
HCLK × (Rsu + Rw + Rh) - ns
tREA RE access time read [1][4] -T
HCLK × Rw - ns
tREH RE high hold time read [1][2][3] -T
HCLK × (Rsu + Rh) - ns
tRHOH RE HIGH to output hold time  input hold for 
flash 
controller; read
-0 --
input hold for 
flash 
controller; 
write 
-0 --
tRHZ RE HIGH to output 
high-impedance time read [1] -T
HCLK × Rh  - ns
tRP RE pulse width read [1][4] -T
HCLK × Rw  - ns
tRR ready to RE LOW time read [1][2][3] -T
HCLK × Rsu - ns
tWB WE HIGH to R/B LOW time write [1][8] -T
HCLK × Ww - ns
tWC WE cycle time write [1][6][7][8] -T
HCLK × (Wsu + Ww + Wh) - ns
Table 18. Dynamic characteristics of SLC NAND flash memory controller  …continued
Tamb =
−
40
°
C to +85
°
C.
Symbol Parameter  Conditions Min Typ Max Unit

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 65 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

[1] THCLK = 1/HCLK

[2] Rsu = bitfield R_SETUP[3:0] in register SLC_TAC[3:0] for reads

[3] Rh = bitfield R_HOLD[3:0] in register SLC_TAC[7:4] for reads

[4] Rw = bitfield R_WIDTH[3:0] in register SLC_TAC[11:8] for reads

[5] Rb = bitfield R_RDY[3:0] in register SLC_TAC[15:12] for reads

[6] Wsu = bitfield W_SETUP[3:0] in register SLC_TAC[19:16] for writes

[7] Wh = bitfield W_HOLD[3:0] in register SLC_TAC[23:20] for writes

[8] Ww = bitfield W_WIDTH[3:0] in register SLC_TAC[27:24] for writes

[9] Wb = bitfield W_RDY[3:0] in register SLC_TAC[31:28] for writes

tWH WE HIGH hold time write [1][6][7] -T

HCLK × (Wsu + Wh) - ns

tWHR WE HIGH to RE LOW time write [1][6][7] -T

HCLK × (Wsu + Wh) - ns

tWP WE pulse width write [1][8] -T

HCLK × Ww - ns

tREHRBL RE HIGH to R/B LOW time write [1][8] -T

HCLK × Ww - ns

Table 18. Dynamic characteristics of SLC NAND flash memory controller …continued

Tamb =

−

C to +85

Symbol Parameter Conditions Min Typ Max Unit

Fig 17. MLC NAND flash memory write timing (writing to NAND flash)

command

tDS tDH

tWB

FLASH_IO[7:0] address

tDS tDH

tALS tALH

tDS tDH

tWP tWH tWC

tCS tCH tCH

tCLS tCLH

command address data

D0 D1 Dn

tALS

tCLH

tALS tALH

tWP tWP tWH

tCLS

tCS

002aae444

FLASH_CE

FLASH_CLE

FLASH_WR

FLASH_ALE

FLASH_RDY

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 66 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Fig 18. MLC NAND Flash memory read timing (reading from NAND flash)

command

tDS tDH

tWB

FLASH_IO[7:0] address

tDS tDH

tALS tALH

tDS tDH

tRP tREH tRC

tRR

tAR

tCS tCH tCEA

tCLR

tCLS tCLH

command address data

tCOH

tREA

D0 D1 D2 D3

tRHZ

tRHOH

tALS tALH

tCLS

tCS

tWP tWH

tWP

002aae445

FLASH_ALE

FLASH_CLE

FLASH_RDY

FLASH_WR

FLASH_RD

FLASH_CE

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 67 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

11.9 SPI and SSP Controller

11.9.1 SPI

[1] THCLK = period time of SPI IP block input clock (HCLK)

Fig 19. MLC NAND flash memory status timing

tCS tCH tCEA

70 h

tDS tDH

status

tRHOH

tCLS tCLH

command data

tCLR

tCOH

tREA

tIR

FLASH_IO[7:0]

tWHR

tWP

tRHZ

FLASH_CLE

FLASH_WR

FLASH_CE

FLASH_RD

002aae446

Table 19. Dynamic characteristics of SPI pins on SPI master controller

Tamb =

−

C to +85

Symbol Parameter Min Typ Max Unit

Common to SPI1 and SPI2

TSPICYC SPI cycle time [1] 2 × THCLK - 256 × THCLK ns

SPI1

tSPIDSU SPI data set-up time - 6 - ns

tSPIDH SPI data hold time - 0 - ns

tSPIDV SPI enable to output data valid time - 2 - ns

tSPIOH SPI output data hold time - 0 - ns

SPI2

tSPIDSU SPI data set-up time - 10 - ns

tSPIDH SPI data hold time - 0 - ns

tSPIDV SPI enable to output data valid time - 2 - ns

tSPIOH SPI output data hold time - 0 - ns

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 68 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

11.9.2 Timing diagrams for SPI and SSP (in SPI mode)

Fig 20. SPI master timing (CPHA = 0)

Fig 21. SPI master timing (CPHA = 1)

002aae457

TSPICYC tSPICLKH tSPICLKL

tSPIDSU tSPIDH

D ATA V ALID DATA VALID

tSPIOH

D ATA V ALID DATA VALID

tSPIQV

SPI1/2_CLK or

SCK0/1 (CPOL = 0)

SPI1/2_CLK or

SCK0/1 (CPOL = 1)

SPI1/2_DATAIO or

MOSI0/1

SPI1/2_DATAIN or

MISO0/1

002aae454

SPICYC

SPICLKH

SPICLKL

SPIDSU

SPIDH

SPIQV

D ATA V ALID DATA V ALID

SPIOH

D ATA V ALID DATA V ALID

SPI1/2_CLK or

SCK0/1 (CPOL = 0)

SPI1/2_CLK or

SCK0/1 (CPOL = 1)

SPI1/2_DATAIO or

MOSI0/1

SPI1/2_DATAIN or

MISO0/1

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 69 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

Fig 22. SPI slave timing (CPHA = 0)

Fig 23. SPI slave timing (CPHA = 1)

002aae458

SPICYC

SPICLKH

SPICLKL

SPIDSU

SPIDH

SPIQV

D ATA V ALID DATA VALID

SPIOH

D ATA V ALID DATA V ALID

SPI1/2_CLK or

SCK0/1 (CPOL = 0)

SPI1/2_CLK or

SCK0/1 (CPOL = 1)

SPI1/2_DATAIO or

MOSI0/1

SPI1/2_DATAIN or

MISO0/1

002aae459

SPICYC

SPICLKH

SPICLKL

SPIDSU

SPIDH

SPIQV

D ATA V ALID DATA VALID

SPIOH

D ATA V ALID DATA VALID

SPI1/2_CLK or

SCK0/1 (CPOL = 0)

SPI1/2_CLK or

SCK0/1 (CPOL = 1)

SPI1/2_DATAIO or

MOSI0/1

SPI1/2_DATAIN or

MISO0/1

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 70 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

12. Package outline

Fig 24. Package outline SOT1048-1 (TFBGA296)

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT1048-1 MO-216

SOT1048-1

07-10-19

07-11-02

UNIT A

max

mm 1.2 0.4

0.3 0.80

0.65 15.1

14.9 15.1

14.9 0.8 13.6 0.15 0.08 0.1

DIMENSIONS (mm are the original dimensions)

TFBGA296: plastic thin fine-pitch ball grid array package; 296 balls

0 5 10 mm

scale

A2b

0.5

0.4

D E e e1e2

13.6

v w y

0.12

246810121416

13579111315 18

1/2 e

AC B

∅ vMC∅ wM

ball A1

index area

ball A1

index area

detail X

AA2A1

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 71 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

13. Abbreviations

Table 20. Abbreviations

Acronym Description

ADC Analog-to-Digital Converter

AHB Advanced High-performance Bus

AMBA Advanced Microcontroller Bus Architec ture

APB Advanced Perip heral Bus

BSDL Boundary Scan Description Language

CISC Complex In struction Set Computer

DDR SDRAM Double Data Rate Synchronous Dynamic Random Access Memory

DMA Direct Memory Access

DSP Digital Signal Processing

ETM Embedded Trace Macrocell

FAB Fast Access Bus

FIFO First In, First Out

FIQ Fast Interrupt Request

GPIO General Purpose Input/Output

I/O Input/Output

IRQ Interrupt Request

HS High-Speed

IrDA Infrared Data Association

JTAG Joint Test Action Group

LCD Liquid Crystal Display

MAC Media Access Control

MIIM Media Independent Interface Management

OHCI Open Host Controller Interface

OTG On-The-Go

PHY Physical Layer

PLL Phase-Locked Loop

PWM Pulse Width Modulator

RAM Random Access Memory

RMII Reduced Media Independent Interface

SE0 Single Ended Zero

SDR SDRAM Single Data Rate Synchronous Dynamic Random Access Memory

SPI Serial Peripheral Interface

SSI Serial Synchronous Interface

SSP Synchronous Serial Port

TFT Thin Film Transistor

TTL Transistor-Transistor Logic

STN Super Twisted Nematic

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 72 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

UART Universal Asynchronous Receiver/Transmitter

USB Universal Serial Bus

VFP Vector Floating Point processor

Table 20. Abbreviations …continued

Acronym Description

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  73 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
14. Revision history
 
Table 21. Revision history
Document ID Release date Data sheet status Change notice Supersedes
LPC3220_30_40_50_1.03 < tbd> Product data sheet - LPC3220_30_ 40_50_1.02
Modifications: •Power supply domain for pins SYSX_IN and SYSX_OUT pins corrected in Table 4.
•Power supply domain for pin VDD_OSC co rrected in Table 4.
•Description of DEBUG pin updated in Table 4.
•Document template updated.
LPC3220_30_40_50_1.02 < tbd> Product data sheet - LPC3220_30_ 40_50_1 
and 
LPC3220_30_40_50_1.01
Modifications: •Added power consumption data (Table 8, Table 9, and Figure 5).
•Changed VESD to 2500 V (HBM) and 1000 V (CDM) in Table 7.
•Static memory controller: added tsu(DQ) value in Table 12.
•DDR SDRAM controller: updated tDQSS value in Table 14.
•Changed data sheet status to Product data sheet.
•Added Table 6 “Supply doma ins”.
•Corrected pin functions for pin T14 (ADIN1/TS_XM) and pin U15 (ADIN0/TS_YM) in 
Table 3 and Table 4.
•Parts LPC3220/01, LPC3230/01, LPC3240/01, LPC3250/01 added.
•Minimum and maximum characterization data added for parameters tsu(Q) and th(Q) over 
temperature range −40 °C to + 85 °C (see Table 14).
•DDR SDRAM characteristics extended to maximum operating frequency foper = 133 MHz 
(see Table 14).
•Parameter VDD(EMC) table notes updated in Table 8.
LPC3220_30_40_50_1 20090206 Preliminary data sheet - -

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 74 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of de vice(s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and tit le. A short data sh eet is intended

for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and

full information. For detailed and full information see the relevant full dat a

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall pre vail.

Product specificatio n — The information and data provided in a Product

data sheet shall define the specification of the product as agr eed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to off er functions and qualities beyond those described in the

Product data sheet.

15.3 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconduct ors’ aggregate and cumulat ive liability toward s

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — NXP Semiconductors product s are not designed,

authorized or warranted to be suitable for use in medical, milit ary, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of an NXP Semiconductors pro duct can reasonably be expected

to result in perso nal injury, death or severe property or environmental

damage. NXP Semiconductors accepts no liab ility for inclusion and/or use of

NXP Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for il lustrative purposes only. NXP Semiconductors makes no

representation or warranty tha t such application s will be suitable for the

specified use without further testing or modification.

NXP Semiconductors does not accept any liability related to any default,

damage, costs or problem which is based on a weakness or default in the

customer application /use or t he application/use of customer’s third party

customer(s) (herei nafter both referred to as “Application”). It is customer’s

sole responsibility to check whether the NXP Semicondu ctors product is

suitable and fit for the Appl ica tion plann ed. Customer has to do all necessary

testing for the Application in order to avoid a def ault of t he Applicat ion and the

product. NXP Semiconductors does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress rating s only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanent ly and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individua l agreement. In case an individual

agreement is concluded only the ter ms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing i n this document may be interpreted or

construed as an of fer t o sell product s that is open for accept ance or t he grant,

conveyance or implication of any license under any copyri ghts, patents or

other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein

may be subject to export control regulatio ns. Export might require a prior

authorization from national authorities.

Quick reference data — The Quick reference data is an extract of the

product data given in the Limiting values and Characteristics sections of this

document, and as such is not complete, exhaustive or legally binding.

Non-automotive qualified products — Unless this data sheet expressly

states tha t t his specific NXP Semiconductors prod uct is automotive qualified,

the product is not suit ab le for aut omotive u se. It is neit her qua lified n or t ested

in accordance with automot ive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualifie d products in automotive equipment or applications.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.

Product [short] dat a sheet Production This document contains the product specification.

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

Product data sheet Rev. 01.03 — 16 March 2010 75 of 77

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

In the event that customer uses the product for design-in and use in

automotive applications to automot ive specifications and standard s, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever cust omer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product claims resulting from customer design and

use of the product for automotive appl ications beyond NXP Semiconductors’

standard warrant y and NXP Semiconductors’ product specificat ions.

15.4 Trademarks

Notice: All referenced b rands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

I2C-bus — logo is a trademark of NXP B.V.

16. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

DRAFT 
DRAFT DRAFT DR
DRAFT DRAFT DRAFT DRAF
DRAFT DRAFT DRAFT DRAFT DRAFT D
DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA
LPC3220_30_40_50_1 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved.
Product data sheet Rev. 01.03 — 16 March 2010  76 of 77
NXP Semiconductors LPC3220/30/40/50
16/32-bit ARM microcontrollers
Contents
General description. . . . . . . . . . . . . . . . . . . . . .  1
Features and benefits . . . . . . . . . . . . . . . . . . . .  1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Ordering information. . . . . . . . . . . . . . . . . . . . .  4
1  Ordering options. . . . . . . . . . . . . . . . . . . . . . . .  4
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Pinning information. . . . . . . . . . . . . . . . . . . . . .  6
1  Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
2  Pin description . . . . . . . . . . . . . . . . . . . . . . . .  10
Functional description . . . . . . . . . . . . . . . . . .  23
1  CPU and subsystems. . . . . . . . . . . . . . . . . . .  23
1.1  CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23
1.2  Vector Floating Point (VFP) coprocessor . . . .  23
1.3  Emulation and  debugging. . . . . . . . . . . . . . . .  23
1.3.1  Embedded ICE . . . . . . . . . . . . . . . . . . . . . . . .  23
1.3.2  Embedded trace buffer. . . . . . . . . . . . . . . . . .  24
2  AHB matrix . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
2.1  APB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25
2.2  FAB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25
3  Physical memory map  . . . . . . . . . . . . . . . . . .  25
4  Internal memory . . . . . . . . . . . . . . . . . . . . . . .  27
4.1  On-chip ROM . . . . . . . . . . . . . . . . . . . . . . . . .  27
4.2  On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . .  27
5  External memory interfaces . . . . . . . . . . . . . .  27
5.1  NAND flash controllers . . . . . . . . . . . . . . . . . .  27
5.1.1  Multi-Level Cell (MLC) NAND flash controller.  27
5.1.2  Single-Level Cell (SLC) NAND flash controller 28
5.2  SD card controller. . . . . . . . . . . . . . . . . . . . . .  28
5.2.1  Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  28
5.3  External memory controller. . . . . . . . . . . . . . .  28
6  AHB master peripherals . . . . . . . . . . . . . . . . .  29
6.1  General Purpose DMA (GPDMA) contro ller  .  29
6.2  Ethernet MAC. . . . . . . . . . . . . . . . . . . . . . . . .  29
6.2.1  Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
6.3  USB interface . . . . . . . . . . . . . . . . . . . . . . . . .  30
6.3.1  USB device controller. . . . . . . . . . . . . . . . . . .  30
6.3.2  USB host controller. . . . . . . . . . . . . . . . . . . . .  31
6.3.3  USB OTG controller . . . . . . . . . . . . . . . . . . . .  31
6.4  LCD controller. . . . . . . . . . . . . . . . . . . . . . . . .  32
6.4.1  Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
7  System functions  . . . . . . . . . . . . . . . . . . . . . .  33
7.1  Interrupt controller  . . . . . . . . . . . . . . . . . . . . .  33
7.2  Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . .  33
7.2.1  Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
7.3  Millisecond timer. . . . . . . . . . . . . . . . . . . . . . .  33
7.3.1  Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
7.4  Clocking and power control features  . . . . . . .  34
7.4.1  Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34
7.4.2  Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . .  34
7.4.3  PLLs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34
7.4.4  Power control modes . . . . . . . . . . . . . . . . . . .  35
7.4.5  Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
8   Communication peripheral interfaces . . . . . .  35
8.1  UARTs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
8.1.1  Standard UARTs. . . . . . . . . . . . . . . . . . . . . . .   36
8.1.2  High-speed UARTs  . . . . . . . . . . . . . . . . . . . .   36
8.2  SPI serial I/O controller . . . . . . . . . . . . . . . . .   36
8.2.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   37
8.3  SSP serial I/O controller. . . . . . . . . . . . . . . . .   37
8.3.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   37
8.4 I2C-bus serial I/O controller . . . . . . . . . . . . . .   37
8.4.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   38
8.5 I2S-bus audio controller . . . . . . . . . . . . . . . . .   38
8.5.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   38
9  Other peripherals. . . . . . . . . . . . . . . . . . . . . .   39
9.1  General purpose parallel I/O . . . . . . . . . . . . .   39
9.1.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   39
9.2  Keyboard scanner . . . . . . . . . . . . . . . . . . . . .   40
9.2.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   40
9.3  Touch screen controller and 10-bit ADC . . . .   40
9.3.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   40
9.4  Real-Time Clock (RTC) and battery RAM . . .   40
9.4.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   41
9.5  Enhanced 32-bit timers/external event 
counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   41
9.5.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   41
9.6  High-speed timer . . . . . . . . . . . . . . . . . . . . . .   42
9.6.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   42
9.7  Pulse Width Modulators (PWMs). . . . . . . . . .   42
9.7.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   42
9.8  Motor control pulse width modulator . . . . . . .   42
9.8.1  Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .   42
Basic architecture. . . . . . . . . . . . . . . . . . . . . .   43
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .   44
Static characteristics  . . . . . . . . . . . . . . . . . . .   45
1  Minimum core voltage requirements . . . . . . .   51
2  Power supply sequencing . . . . . . . . . . . . . . .   51
3  Power consumptio n per peripheral  . . . . . . . .   51
4  Power consumption in Run mode . . . . . . . . .   52
5  ADC static characteristics . . . . . . . . . . . . . . .   53
Dynamic characteristics. . . . . . . . . . . . . . . . .   55
1  Clocking and I/O port pins . . . . . . . . . . . . . . .   55
2  Static memory controller  . . . . . . . . . . . . . . . .   55
3  SDR SDRAM Controller. . . . . . . . . . . . . . . . .   58
4  DDR SDRAM controller . . . . . . . . . . . . . . . . .   59
5  USB controller . . . . . . . . . . . . . . . . . . . . . . . .   61
6  Secure Digital (SD) card interface . . . . . . . . .   61
7  MLC NAND flash memory controller . . . . . . .   62
8  SLC NAND flash memory controller  . . . . . . .   63
9  SPI and SSP Controller . . . . . . . . . . . . . . . . .   67
9.1  SPI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   67
9.2  Timing diagrams for SPI and SSP 
(in SPI mode). . . . . . . . . . . . . . . . . . . . . . . . .   68
Package outline. . . . . . . . . . . . . . . . . . . . . . . .   70
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .   71
Revision history . . . . . . . . . . . . . . . . . . . . . . .   73
Legal information . . . . . . . . . . . . . . . . . . . . . .   74
1  Data sheet status. . . . . . . . . . . . . . . . . . . . . .   74

DRAFT

DRAFT DRAFT DR

DRAFT DRAFT DRAFT DRAF

DRAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT DRAFT DRAFT DRAFT DRAFT DRAFT DRA

NXP Semiconductors LPC3220/30/40/50

16/32-bit ARM microcontrollers

For more information, please visit: http://www.nxp.co m

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 16 March 2010

Document identifier: LPC3220_30_40_50_1

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

15.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

15.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 74

15.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 75

16 Contact information. . . . . . . . . . . . . . . . . . . . . 75

17 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76