S-19243xxxA Series www.ablic.com www.ablicinc.com AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 (c) ABLIC Inc., 2016-2018 The S-19243xxxA Series developed by using high-withstand voltage CMOS process technology, is a positive voltage regulator with high-accuracy output voltage and high output current. A built-in overcurrent protection circuit to limit overcurrent of the output transistor and a built-in thermal shutdown circuit to limit heat are included. In addition to the type in which output voltage is set inside the IC, the type for which output voltage can be set via an external resistor is added to a lineup. Also, the S-19243xxxA Series includes the soft-start function to adjust the output voltage rising time at power-on or at the time when the ON / OFF pin is set to ON. Caution This product can be used in vehicle equipment and in-vehicle equipment. Before using the product in the purpose, contact to ABLIC Inc. is indispensable. Features * Output voltage (internally set): * Output voltage (externally set): * Input voltage: * Output voltage accuracy: * Dropout voltage: * Current consumption: * Output current: * Ripple rejection: * Built-in overcurrent protection circuit: * Built-in thermal shutdown circuit: * Built-in soft-start circuit: * Built-in ON / OFF circuit: * Operation temperature range: * Lead-free (Sn 100%), halogen-free *2 * AEC-Q100 qualified 1.0 V to 6.0 V, selectable in 0.05 V step 1.0 V to 9.0 V, settable via external resistor (HSOP-8A, HSOP-6 and HSNT-8(2030) only) 2.5 V to 10.0 V 2.3% (Tj = -40C to +125C) 0.09 V typ. (2.6 V output product, at IOUT = 200 mA) During operation: 120 A typ., 150 A max. (Tj = -40C to +150C) During power-off: 0.1 A typ., 10.5 A max. (Tj = -40C to +125C) *1 Possible to output 500 mA (at VIN VOUT(S) + 1.0 V) 60 dB typ. (at f = 1.0 kHz) Limits overcurrent of output transistor. Detection temperature 170C typ. Adjusts output voltage rising time at power-on or at the time when ON / OFF pin is set to ON. Adjustable type: E / F / G / H type, tSS = 6.0 ms typ. (CSS = 10 nF) Soft-start time can be changed by the capacitor (CSS). Fixed type: A / B / C / D type: Fixed to tSS = 1.0 ms typ. Ensures long battery life Discharge shunt function "available" / "unavailable" is selectable. Pull-down function "available" / "unavailable" is selectable. Ta = -40C to +125C *1. Please make sure that the loss of the IC will not exceed the power dissipation when the output current is large. *2. Contact our sales office for details. Applications * Constant-voltage power supply for electrical application for vehicle interior * Constant-voltage power supply for home electric appliance * For automotive use (engine, transmission, suspension, ABS, related-devices for EV / HEV / PHEV, etc.) Packages * TO-252-5S(A) * HSOP-8A * HSOP-6 * SOT-89-5 * HSNT-8(2030) 1 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Block Diagrams 1. Types in which output voltage is internally set 1. 1 S-19243xxxA Series A / B / C / D type (HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030)) *1 VIN VOUT Overcurrent protection circuit Thermal shutdown circuit + ON / OFF circuit ON / OFF - *2 *3 Reference voltage circuit Soft-start circuit *1 VSS Product Type A B C D ON / OFF Logic Active "H" Active "H" Active "H" Active "H" Soft-start Time Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Discharge Shunt *2 Function Available Available Unavailable Unavailable Pull-down Resistor *3 Available Unavailable Available Unavailable *1. Parasitic diode *2. A / B type (With discharge shunt function): ON, C / D type (Without discharge shunt function): OFF *3. A / C type (With pull-down resistor): ON, B / D type (Without pull-down resistor): OFF Figure 1 2 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 1. 2 S-19243xxxA Series E / F / G / H type (TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030)) *1 VOUT VIN Overcurrent protection circuit Thermal shutdown circuit + ON / OFF circuit ON / OFF - *2 *3 Reference voltage circuit Soft-start circuit *1 SSC *1 VSS Product Type E F G H ON / OFF Logic Active "H" Active "H" Active "H" Active "H" Soft-start Time Changeable by capacitor (CSS) Changeable by capacitor (CSS) Changeable by capacitor (CSS) Changeable by capacitor (CSS) Discharge Shunt *2 Function Available Available Unavailable Unavailable Pull-down Resistor *3 Available Unavailable Available Unavailable *1. Parasitic diode *2. E / F type (With discharge shunt function): ON, G / H type (Without discharge shunt function): OFF *3. E / G type (With pull-down resistor): ON, F / H type (Without pull-down resistor): OFF Figure 2 3 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. Types in which output voltage is externally set 2. 1 S-19243xxxA Series A / B / C / D type (HSOP-6) *1 VIN VOUT Overcurrent protection circuit VADJ Thermal shutdown circuit + ON / OFF circuit ON / OFF - *2 *3 Reference voltage circuit Soft-start circuit *1 VSS Product Type A B C D ON / OFF Logic Active "H" Active "H" Active "H" Active "H" Soft-start Time Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Fixed to tSS = 1.0 ms typ. Discharge Shunt *2 Function Available Available Unavailable Unavailable Pull-down Resistor *3 Available Unavailable Available Unavailable *1. Parasitic diode *2. A / B type (With discharge shunt function): ON, C / D type (Without discharge shunt function): OFF *3. A / C type (With pull-down resistor): ON, B / D type (Without pull-down resistor): OFF Figure 3 4 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. 2 S-19243xxxA Series E / F / G / H type (HSOP-8A, HSNT-8(2030)) *1 VIN VOUT Overcurrent protection circuit VADJ Thermal shutdown circuit + ON / OFF circuit ON / OFF - *2 *3 Reference voltage circuit Soft-start circuit *1 SSC *1 VSS Product Type E F G H ON / OFF Logic Active "H" Active "H" Active "H" Active "H" Soft-start Time Changeable by capacitor (CSS) Changeable by capacitor (CSS) Changeable by capacitor (CSS) Changeable by capacitor (CSS) Discharge Shunt *2 Function Available Available Unavailable Unavailable Pull-down Resistor *3 Available Unavailable Available Unavailable *1. Parasitic diode *2. E / F type (With discharge shunt function): ON, G / H type (Without discharge shunt function): OFF *3. E / G type (With pull-down resistor): ON, F / H type (Without pull-down resistor): OFF Figure 4 5 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series AEC-Q100 Qualified This IC supports AEC-Q100 for operation temperature grade 1. Contact our sales office for details of AEC-Q100 reliability specification. Product Name Structure Users can select the product type, output voltage and package type for the S-19243xxxA Series. Refer to "1. Product name" regarding the contents of product name, "2. Function list of product type" regarding the product type, "3. Packages" regarding the package drawings and "4. Product name list" for details of product names. 1. Product name S-19243 x xx A - xxxx U Environmental code U: Lead-free (Sn 100%), halogen-free Package abbreviation and IC packing specifications*1 V5T2: TO-252-5S(A), Tape E8T1: HSOP-8A, Tape E6T1: HSOP-6, Tape U5T1: SOT-89-5, Tape A8T1: HSNT-8(2030), Tape Operation temperature A: Ta = -40C to +125C Output voltage*2 00: Externally set*3 10 to 60: Internally set (e.g., when the output voltage is 1.0 V, it is expressed as 10.) *3 Product type A to H *1. *2. *3. 6 Refer to the tape drawing. If you request the product which has 0.05 V step, contact our sales office. Refer to "2. Function list of product type". AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. Function list of product type Table 1 Discharge Shunt Function Product Type ON / OFF Logic Soft-start Time A Active "H" Fixed to tSS = 1.0 ms typ.*1 Available Fixed to tSS = 1.0 ms typ.*1 Available Fixed to tSS = 1.0 ms typ.*1 Unavailable Fixed to tSS = 1.0 ms typ.*1 Unavailable B Active "H" C Active "H" D Active "H" E Active "H" Pull-down Resistor Available Output Voltage Internally set Externally set Unavailable Internally set Externally set Available Internally set Externally set Unavailable Internally set Externally set Changeable by Available the capacitor (CSS) Available Internally set Externally set F Active "H" Changeable by Available the capacitor (CSS) Unavailable Internally set Externally set G Active "H" Changeable by Unavailable the capacitor (CSS) Available Internally set Externally set H Active "H" Changeable by Unavailable the capacitor (CSS) Unavailable Internally set Externally set *1. Package HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-6 HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-6 HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-6 HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-6 TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-8A, HSNT-8(2030) TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-8A, HSNT-8(2030) TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-8A, HSNT-8(2030) TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030) HSOP-8A, HSNT-8(2030) The soft-start time (tSS) is fixed to 1.0 ms typ. that cannot be changed. 3. Packages Table 2 Package Name TO-252-5S(A) HSOP-8A HSOP-6 SOT-89-5 HSNT-8(2030) Package Drawing Codes Dimension Tape Reel Land VA005-A-P-SD FH008-A-P-SD FH006-A-P-SD UP005-A-P-SD PP008-A-P-SD VA005-A-C-SD FH008-A-C-SD FH006-A-C-SD UP005-A-C-SD PP008-A-C-SD VA005-A-R-SD FH008-A-R-SD FH006-A-R-S1 UP005-A-R-SD PP008-A-R-SD VA005-A-L-SD FH008-A-L-SD FH006-A-L-SD - PP008-A-L-SD 7 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 4. Product name list 4. 1 S-19243xxxA Series A type ON / OFF logic Pull-down resistor : Active "H" : Available Discharge shunt function : Available Soft-start time : Fixed to tSS = 1.0 ms typ. Table 3 Output Voltage Externally set HSOP-8A - HSOP-6 SOT-89-5 - HSNT-8(2030) - S-19243A00A-E6T1U 1.2 V 2.3% S-19243A12A-E8T1U S-19243A12A-E6T1U S-19243A12A-U5T1U S-19243A12A-A8T1U 1.8 V 2.3% S-19243A18A-E8T1U S-19243A18A-E6T1U S-19243A18A-U5T1U S-19243A18A-A8T1U 3.3 V 2.3% S-19243A33A-E8T1U S-19243A33A-E6T1U S-19243A33A-U5T1U S-19243A33A-A8T1U 5.0 V 2.3% S-19243A50A-E8T1U S-19243A50A-E6T1U S-19243A50A-U5T1U S-19243A50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 2 S-19243xxxA Series B type ON / OFF logic Pull-down resistor : Active "H" : Unavailable Discharge shunt function : Available Soft-start time : Fixed to tSS = 1.0 ms typ. Table 4 Output Voltage Externally set HSOP-8A - HSOP-6 SOT-89-5 - HSNT-8(2030) - S-19243B00A-E6T1U 1.2 V 2.3% S-19243B12A-E8T1U S-19243B12A-E6T1U S-19243B12A-U5T1U S-19243B12A-A8T1U 1.8 V 2.3% S-19243B18A-E8T1U S-19243B18A-E6T1U S-19243B18A-U5T1U S-19243B18A-A8T1U 3.3 V 2.3% S-19243B33A-E8T1U S-19243B33A-E6T1U S-19243B33A-U5T1U S-19243B33A-A8T1U 5.0 V 2.3% S-19243B50A-E8T1U S-19243B50A-E6T1U S-19243B50A-U5T1U S-19243B50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 3 S-19243xxxA Series C type ON / OFF logic Pull-down resistor : Active "H" : Available Discharge shunt function : Unavailable Soft-start time : Fixed to tSS = 1.0 ms typ. Table 5 Output Voltage Externally set HSOP-6 SOT-89-5 HSNT-8(2030) - - S-19243C00A-E6T1U 1.2 V 2.3% S-19243C12A-E8T1U S-19243C12A-E6T1U S-19243C12A-U5T1U S-19243C12A-A8T1U 1.8 V 2.3% S-19243C18A-E8T1U S-19243C18A-E6T1U S-19243C18A-U5T1U S-19243C18A-A8T1U 3.3 V 2.3% S-19243C33A-E8T1U S-19243C33A-E6T1U S-19243C33A-U5T1U S-19243C33A-A8T1U 5.0 V 2.3% S-19243C50A-E8T1U S-19243C50A-E6T1U S-19243C50A-U5T1U S-19243C50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 4 HSOP-8A - S-19243xxxA Series D type ON / OFF logic Pull-down resistor : Active "H" : Unavailable Discharge shunt function : Unavailable Soft-start time : Fixed to tSS = 1.0 ms typ. Table 6 Output Voltage Externally set HSOP-8A - HSOP-6 SOT-89-5 - HSNT-8(2030) - S-19243D00A-E6T1U 1.2 V 2.3% S-19243D12A-E8T1U S-19243D12A-E6T1U S-19243D12A-U5T1U S-19243D12A-A8T1U 1.8 V 2.3% S-19243D18A-E8T1U S-19243D18A-E6T1U S-19243D18A-U5T1U S-19243D18A-A8T1U 3.3 V 2.3% S-19243D33A-E8T1U S-19243D33A-E6T1U S-19243D33A-U5T1U S-19243D33A-A8T1U 5.0 V 2.3% S-19243D50A-E8T1U S-19243D50A-E6T1U S-19243D50A-U5T1U S-19243D50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 8 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 4. 5 S-19243xxxA Series E type ON / OFF logic Pull-down resistor : Active "H" : Available Discharge shunt function : Available Soft-start time : Changeable by CSS Table 7 Output Voltage Externally set HSOP-8A HSOP-6 SOT-89-5 HSNT-8(2030) - - S-19243E00A-E8T1U S-19243E00A-A8T1U 1.2 V 2.3% S-19243E12A-V5T2U S-19243E12A-E8T1U S-19243E12A-E6T1U S-19243E12A-U5T1U S-19243E12A-A8T1U 1.8 V 2.3% S-19243E18A-V5T2U S-19243E18A-E8T1U S-19243E18A-E6T1U S-19243E18A-U5T1U S-19243E18A-A8T1U 3.3 V 2.3% S-19243E33A-V5T2U S-19243E33A-E8T1U S-19243E33A-E6T1U S-19243E33A-U5T1U S-19243E33A-A8T1U 5.0 V 2.3% S-19243E50A-V5T2U S-19243E50A-E8T1U S-19243E50A-E6T1U S-19243E50A-U5T1U S-19243E50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 6 TO-252-5S(A) - S-19243xxxA Series F type ON / OFF logic Pull-down resistor : Active "H" : Unavailable Discharge shunt function : Available Soft-start time : Changeable by CSS Table 8 Output Voltage Externally set HSOP-8A HSOP-6 SOT-89-5 HSNT-8(2030) - - S-19243F00A-E8T1U S-19243F00A-A8T1U 1.2 V 2.3% S-19243F12A-V5T2U S-19243F12A-E8T1U S-19243F12A-E6T1U S-19243F12A-U5T1U S-19243F12A-A8T1U 1.8 V 2.3% S-19243F18A-V5T2U S-19243F18A-E8T1U S-19243F18A-E6T1U S-19243F18A-U5T1U S-19243F18A-A8T1U 3.3 V 2.3% S-19243F33A-V5T2U S-19243F33A-E8T1U S-19243F33A-E6T1U S-19243F33A-U5T1U S-19243F33A-A8T1U 5.0 V 2.3% S-19243F50A-V5T2U S-19243F50A-E8T1U S-19243F50A-E6T1U S-19243F50A-U5T1U S-19243F50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 7 TO-252-5S(A) - S-19243xxxA Series G type ON / OFF logic Pull-down resistor : Active "H" : Available Discharge shunt function : Unavailable Soft-start time : Changeable by CSS Table 9 Output Voltage Externally set HSOP-8A HSOP-6 SOT-89-5 HSNT-8(2030) - - S-19243G00A-E8T1U S-19243G00A-A8T1U 1.2 V 2.3% S-19243G12A-V5T2U S-19243G12A-E8T1U S-19243G12A-E6T1U S-19243G12A-U5T1U S-19243G12A-A8T1U 1.8 V 2.3% S-19243G18A-V5T2U S-19243G18A-E8T1U S-19243G18A-E6T1U S-19243G18A-U5T1U S-19243G18A-A8T1U 3.3 V 2.3% S-19243G33A-V5T2U S-19243G33A-E8T1U S-19243G33A-E6T1U S-19243G33A-U5T1U S-19243G33A-A8T1U 5.0 V 2.3% S-19243G50A-V5T2U S-19243G50A-E8T1U S-19243G50A-E6T1U S-19243G50A-U5T1U S-19243G50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 4. 8 TO-252-5S(A) - S-19243xxxA Series H type ON / OFF logic Pull-down resistor : Active "H" : Unavailable Discharge shunt function : Unavailable Soft-start time : Changeable by CSS Table 10 Output Voltage Externally set TO-252-5S(A) - HSOP-8A HSOP-6 SOT-89-5 HSNT-8(2030) - - S-19243H00A-E8T1U S-19243H00A-A8T1U 1.2 V 2.3% S-19243H12A-V5T2U S-19243H12A-E8T1U S-19243H12A-E6T1U S-19243H12A-U5T1U S-19243H12A-A8T1U 1.8 V 2.3% S-19243H18A-V5T2U S-19243H18A-E8T1U S-19243H18A-E6T1U S-19243H18A-U5T1U S-19243H18A-A8T1U 3.3 V 2.3% S-19243H33A-V5T2U S-19243H33A-E8T1U S-19243H33A-E6T1U S-19243H33A-U5T1U S-19243H33A-A8T1U 5.0 V 2.3% S-19243H50A-V5T2U S-19243H50A-E8T1U S-19243H50A-E6T1U S-19243H50A-U5T1U S-19243H50A-A8T1U Remark Please contact our sales office for products with specifications other than the above output voltage. 9 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Pin Configurations 1. TO-252-5S(A) Table 11 S-19243xxxA Series E / F / G / H Type, *1 Types in Which Output Voltage is Internally Set Top view Pin No. 3 1 2 4 Symbol Description 1 VOUT Output voltage pin 2 ON / OFF ON / OFF pin 3 VSS GND pin 4 SSC*2 Soft-start pin 5 VIN Input voltage pin 5 Figure 5 *1. Types in which output voltage is externally set are unavailable. *2. Connect a capacitor between the SSC pin and the VSS pin. The soft-start time at power-on and at the time when the ON / OFF pin is set to ON can be adjusted according to the capacitance. 10 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. HSOP-8A Table 12 S-19243xxxA Series A / B / C / D Type, Types in Which Output Voltage is Internally Set Top view 1 8 2 7 3 6 4 5 Bottom view 8 1 7 2 6 3 5 4 *1 Figure 6 Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT*2 VOUT*2 VSS NC*3 ON / OFF NC*3 NC*3 VIN Description Output voltage pin Output voltage pin GND pin No connection ON / OFF pin No connection No connection Input voltage pin Table 13 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Internally Set Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT NC*3 VSS ON / OFF SSC*4 NC*3 NC*3 VIN Description Output voltage pin No connection GND pin ON / OFF pin Soft-start pin No connection No connection Input voltage pin Table 14 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Externally Set Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT VADJ VSS ON / OFF SSC*4 NC*3 NC*3 VIN Description Output voltage pin Output voltage adjustment pin GND pin ON / OFF pin Soft-start pin No connection No connection Input voltage pin *1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND. However, do not use it as the function of electrode. *2. Although pins of number 1 and 2 are connected internally, be sure to short-circuit them nearest in use. *3. The NC pin is electrically open. The NC pin can be connected to the VIN pin or the VSS pin. *4. Connect a capacitor between the SSC pin and the VSS pin. The soft-start time at power-on and at the time when the ON / OFF pin is set to ON can be adjusted according to the capacitance. 11 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 3. HSOP-6 Table 15 S-19243xxxA Series A / B / C / D Type, Types in Which Output Voltage is Internally Set Top view 6 5 4 1 2 3 Figure 7 Pin No. 1 2 3 4 5 6 Symbol VOUT VSS ON / OFF NC*1 VSS VIN Description Output voltage pin GND pin ON / OFF pin No connection GND pin Input voltage pin Table 16 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Internally Set Pin No. 1 2 3 4 5 6 Symbol VOUT VSS ON / OFF SSC*2 VSS VIN Description Output voltage pin GND pin ON / OFF pin Soft-start pin GND pin Input voltage pin Table 17 S-19243xxxA Series A / B / C / D Type, Types in Which Output Voltage is Externally Set Pin No. 1 2 3 4 5 6 Symbol VOUT VSS VADJ ON / OFF VSS VIN Description Output voltage pin GND pin Output voltage adjustment pin ON / OFF pin GND pin Input voltage pin *1. The NC pin is electrically open. The NC pin can be connected to the VIN pin or the VSS pin. *2. Connect a capacitor between the SSC pin and the VSS pin. The soft-start time at power-on and at the time when the ON / OFF pin is set to ON can be adjusted according to the capacitance. 12 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 4. SOT-89-5 Table 18 S-19243xxxA Series A / B / C / D Type, Types in Which Output Voltage is Internally Set*1 Top view 5 1 4 2 Figure 8 Pin No. 1 2 3 4 5 Symbol ON / OFF VSS NC*2 VIN VOUT Description ON / OFF pin GND pin No connection Input voltage pin Output voltage pin 3 Table 19 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Internally Set*1 Pin No. 1 2 3 4 5 Symbol ON / OFF VSS SSC*3 VIN VOUT Description ON / OFF pin GND pin Soft-start pin Input voltage pin Output voltage pin *1. Types in which output voltage is externally set are unavailable. *2. The NC pin is electrically open. The NC pin can be connected to the VIN pin or the VSS pin. *3. Connect a capacitor between the SSC pin and the VSS pin. The soft-start time at power-on and at the time when the ON / OFF pin is set to ON can be adjusted according to the capacitance. 13 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 4. HSNT-8(2030) Table 20 S-19243xxxA Series A / B / C / D Type, Types in Which Output Voltage is Internally Set Top view 1 8 4 5 Bottom view 8 1 5 4 Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT*2 VOUT*2 VSS NC*3 ON / OFF NC*3 NC*3 VIN Description Output voltage pin Output voltage pin GND pin No connection ON / OFF pin No connection No connection Input voltage pin *1 Figure 9 Table 21 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Internally Set Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT*2 VOUT*2 VSS ON / OFF SSC*4 NC*3 NC*3 VIN Description Output voltage pin Output voltage pin GND pin ON / OFF pin Soft-start pin No connection No connection Input voltage pin Table 22 S-19243xxxA Series E / F / G / H Type, Types in Which Output Voltage is Externally Set Pin No. 1 2 3 4 5 6 7 8 Symbol VOUT VADJ VSS ON / OFF SSC*4 NC*3 NC*3 VIN Description Output voltage pin Output voltage adjustment pin GND pin ON / OFF pin Soft-start pin No connection No connection Input voltage pin *1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND. However, do not use it as the function of electrode. *2. Although pins of number 1 and 2 are connected internally, be sure to short-circuit them nearest in use. *3. The NC pin is electrically open. The NC pin can be connected to the VIN pin or the VSS pin. *4. Connect a capacitor between the SSC pin and the VSS pin. The soft-start time at power-on and at the time when the ON / OFF pin is set to ON can be adjusted according to the capacitance. 14 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Absolute Maximum Ratings Table 23 (Ta = +25C unless otherwise specified) Item Symbol Absolute Maximum Rating VSS - 0.3 to VSS + 12 VIN VSS - 0.3 to VIN + 0.3 VSS + 12 V VSSC VSS - 0.3 to VIN + 0.3 VSS + 12 V VVADJ VSS - 0.3 to VSS + 12 VSS - 0.3 to VIN + 0.3 VSS + 12 V 550 mA -40 to +150 C VON / OFF Input voltage Output voltage Unit V VOUT Output current IOUT Junction temperature Tj V Operation ambient temperature Topr -40 to +125 C Storage temperature Tstg -40 to +150 C Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Thermal Resistance Value Table 24 Item Min. - - - - - - - - - - - - - - - - Typ. 86 60 38 31 28 104 74 39 37 31 96 74 - 44 41 Board B Board C Board D - - - 84 - Board E Board A Board B HSNT-8(2030) Board C Board D Board E Test environment: compliance with JEDEC STANDARD JESD51-2A - - - - - - Junction-to-ambient thermal resistance*1 Symbol JA Condition Board A Board B TO-252-5S(A) Board C Board D Board E Board A Board B HSOP-8A Board C Board D Board E Board A Board B HSOP-6 Board C Board D Board E Board A SOT-89-5 *1. Remark Max. - - - - - - - - - - - - - - - - Unit C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W C/W 46 - - - C/W C/W C/W 35 181 135 40 42 32 - - - - - - C/W C/W C/W C/W C/W C/W 119 Refer to " Power Dissipation" and "Test Board" for details. 15 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Electrical Characteristics 1. Types in which output voltage is internally set (S-19243x10 to S-19243x60) Table 25 (1 / 2) Item Output voltage*1 Symbol VOUT(E) Output current*2 IOUT Dropout voltage*3 Vdrop Line regulation VOUT1 VIN * VOUT Load regulation Current consumption during operation VOUT2 ISS1 Current consumption during power-off ISS2 Input voltage VIN 16 Condition (Tj = -40C to +150C unless otherwise specified) Test Min. Typ. Max. Unit Circuit VOUT(S) VOUT(S) VOUT(S) < 1.5 V V V 1 x 0.977 OUT(S) x 1.023 VIN = 2.5 V, IOUT = 100 mA, Tj = -40C to +125C VIN = VOUT(S) + 1.0 V, VOUT(S) VOUT(S) 1.5 V VOUT(S) IOUT = 100 mA, V V x 0.977 OUT(S) x 1.023 Tj = -40C to +125C VIN = 2.5 V VOUT(S) < 1.5 V 500*5 - - mA VIN VOUT(S) + 1.0 V 1.5 V VOUT(S) 500*5 - - mA - *4 - V 1.0 V VOUT(S) < 2.0 V IOUT = 200 mA, 2.0 V VOUT(S) < 2.6 V - 0.52 - V Ta = +25C 2.6 V VOUT(S) 6.0 V - 0.09 - V 2.5 V VIN 10 V, VOUT(S) < 2.0 V - 0.05 0.2 %/V IOUT = 100 mA, Ta = +25C VOUT(S) + 0.5 V VIN 10 V, - 0.05 0.2 %/V 2.0 V VOUT(S) IOUT = 100 mA, Ta = +25C VIN = 2.5 V, VOUT(S) < 1.5 V - 15 30 mV 1 mA IOUT 200 mA, Ta = +25C VIN = VOUT(S) + 1.0 V, 1.5 V VOUT(S) - 15 30 mV 1 mA IOUT 200 mA, Ta = +25C VIN = 2.5 V, - 120 150 A VOUT(S) < 1.5 V ON / OFF pin = ON, no load VIN = VOUT(S) + 1.0 V, - 120 150 A 1.5 V VOUT(S) ON / OFF pin = ON, no load VIN = 2.5 V, ON / OFF pin = OFF, no load, VOUT(S) < 1.5 V - 0.1 10.5 A Tj = -40C to +125C VIN = VOUT(S) + 1.0 V, - 0.1 10.5 A ON / OFF pin = OFF, no load, 1.5 V VOUT(S) Tj = -40C to +125C - 2.5 - 10 V 1 3 3 1 1 1 1 1 1 1 2 2 2 2 - AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Table 25 (2 / 2) Item ON / OFF pin input voltage "H" ON / OFF pin input voltage "L" ON / OFF pin input current "H" ON / OFF pin input current "L" Ripple rejection Short-circuit current Symbol VSH VSL Soft-start time*6 VIN = 2.5 V, RL = 1 k, determined by VOUT output level VIN = VOUT(S) + 1.0 V, RL = 1 k, determined by VOUT output level VIN = 2.5 V, RL = 1 k, determined by VOUT output level VIN = VOUT(S) + 1.0 V, RL = 1 k, determined by VOUT output level VOUT(S) < 1.5 V 2.1 - - V 4 1.5 V VOUT(S) 2.1 - - V 4 VOUT(S) < 1.5 V - - 0.6 V 4 1.5 V VOUT(S) - - 0.6 V 4 -0.1 0.8 - 2.5 0.1 7.8 A A 4 4 -0.1 - 0.1 A 4 VIN = 3.0 V, f = 1 kHz, 1.0 V V OUT(S) < 1.5 V Vrip = 0.5 Vrms, 1.5 V VOUT(S) < 2.0 V IOUT = 100 mA VIN = VOUT(S) + 1.0 V, 2.0 V VOUT(S) < 2.6 V f = 1 kHz, Vrip = 0.5 Vrms, 2.6 V VOUT(S) 6.0 V IOUT = 100 mA VIN = 2.5 V, VOUT(S) < 1.5 V ON / OFF pin = ON, VOUT = 0 V, Ta = +25C VIN = VOUT(S) + 1.0 V, 1.5 V VOUT(S) ON / OFF pin = ON, VOUT = 0 V, Ta = +25C - 60 - dB 5 - 55 - dB 5 - 55 - dB 5 - 50 - dB 5 - 240 - mA 3 - 240 - mA 3 Junction temperature - 170 - C - Junction temperature - 135 - C - A / B / E / F type - 100 - 6 A / C / E / G type 1.3 4.0 12 M 4 - 1.0 - ms 7 - 1.0 - ms 7 ISH VIN = 10 V, VON / OFF = 10 V ISL VIN = 10 V, VON / OFF = 0 V |RR| Ishort Thermal shutdown T detection temperature SD Thermal shutdown TSR release temperature Discharge shunt RLOW resistance during power-off ON / OFF pin pull-down resistance Condition RPD tSS (Tj = -40C to +150C unless otherwise specified) Test Min. Typ. Max. Unit Circuit VIN = 10 V, VOUT = 0.1 V - VIN = 2.5 V, ON / OFF pin = ON VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON B / D / F / H type A / C / E / G type VOUT(S) < 1.5 V, A / B / C / D type 1.5 V VOUT(S), A / B / C / D type *1. VOUT(S): Set output voltage VOUT(E): Actual output voltage Output voltage when fixing IOUT (= 100 mA) and inputting 2.5 V or VOUT(S) + 1.0 V. *2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current. *3. Vdrop = VIN1 - (VOUT3 x 0.98) VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input voltage. VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 200 mA. *4. The dropout voltage is limited by the difference between the input voltage (min. value) and the set output voltage. In case of 1.0 V VOUT(S) < 1.5 V: 2.5 V - VOUT(S) = Vdrop In case of 1.5 V VOUT(S) < 2.0 V: (VOUT(S) + 1.0 V) - VOUT(S) = 1.0 V *5. Due to limitation of the power dissipation, this value may not be satisfied. Attention should be paid to the power dissipation when the output current is large. This specification is guaranteed by design. *6. Soft-start time shows the time period from immediately after power-on or when the ON / OFF pin is set to ON until the output voltage rises to 99%. Refer to "8. Soft-start function" in " Operation" for details. 17 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. Types in which output voltage is externally set (S-19243x00, HSOP-8A, HSOP-6, HSNT-8(2030)) Table 26 Item Adjustment pin output voltage *1 Output voltage range Adjustment pin internal resistance Output current*2 Dropout voltage*3 Line regulation Symbol VVADJ VROUT IOUT Vdrop VOUT1 VIN * VOUT VOUT2 Current consumption during operation ISS1 Current consumption during power-off ISS2 VIN VSH VSL ISH ISL Ripple rejection |RR| Short-circuit current Ishort Thermal shutdown detection temperature Thermal shutdown release temperature Discharge shunt resistance during power-off ON / OFF pin pull-down resistance Soft-start time*6 - RVADJ Load regulation Input voltage ON / OFF pin input voltage "H" ON / OFF pin input voltage "L" ON / OFF pin input current "H" ON / OFF pin input current "L" (Tj = -40C to +150C unless otherwise specified) Test Condition Min. Typ. Max. Unit Circuit VOUT = VVADJ, VIN = 2.5 V, IOUT = 100 mA, 0.977 1.0 1.023 V 8 Tj = -40C to +125C - 1.0 - 9.0 V 15 - 600 - k - - *4 - - mA V 10 8 - 0.05 0.2 %/V 8 - 15 30 mV 8 - 120 150 A 9 - 0.1 10.5 A 9 2.5 - 10 V - 2.1 - - V 11 - - 0.6 V 11 *5 VOUT = VVADJ, VIN = 2.5 V VOUT = VVADJ, IOUT = 200 mA, Ta = +25C VOUT = VVADJ, 2.5 V VIN 10 V, IOUT = 100 mA, Ta = +25C VOUT = VVADJ, VIN = 2.5 V, 1 mA IOUT 200 mA, Ta = +25C VOUT = VVADJ, VIN = 2.5 V, ON / OFF pin = ON, no load VOUT = VVADJ, VIN = 2.5 V, ON / OFF pin = OFF, no load, Tj = -40C to +125C - VOUT = VVADJ, VIN = 2.5 V, RL = 1 k, determined by VOUT output level VOUT = VVADJ, VIN = 2.5 V, RL = 1 k, determined by VOUT output level B / D / F / H type VIN = 10 V, ON / OFF = 10 V A / C / E / G type 500 - -0.1 0.8 - 2.5 0.1 7.8 A A 11 11 VIN = 10 V, ON / OFF = 0 V -0.1 - 0.1 A 11 - 60 - dB 12 - 240 - mA 10 VOUT = VVADJ, VIN = 3.0 V, f = 1 kHz, Vrip = 0.5 Vrms, IOUT = 100 mA VOUT = VVADJ, VIN = 2.5 V, ON / OFF pin = ON, VOUT = 0 V, Ta = +25C TSD Junction temperature - 170 - C - TSR Junction temperature - 135 - C - RLOW VIN = 10 V, VOUT = 0.1 V A / B / E / F type - 100 - 13 A / C / E / G type 1.3 4.0 12 M 11 A / B / C / D type - 1.0 - ms 14 RPD tSS - VOUT = VVADJ, VIN = 2.5 V, ON / OFF pin = ON *1. Output voltage when fixing IOUT (= 100 mA) and inputting 2.5 V. *2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current. *3. Vdrop = VIN1 - (VOUT3 x 0.98) VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input voltage. VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 200 mA. *4. The dropout voltage is limited by the difference between the input voltage (min. value) and the set output voltage. In case of set output voltage (VOUT(S)) = 1.0 V: 2.5 V - VOUT(S) = Vdrop *5. Due to limitation of the power dissipation, this value may not be satisfied. Attention should be paid to the power dissipation when the output current is large. This specification is guaranteed by design. *6. Soft-start time shows the time period from immediately after power-on or when the ON / OFF pin is set to ON until the output voltage rises to 99%. Refer to "8. Soft-start function" in " Operation" for details. 18 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Test Circuits 1. Types in which output voltage is internally set (S-19243x10 to S-19243x60) SSC + VOUT VIN *1 V ON / OFF A + VSS Set to ON Figure 10 VOUT VIN SSC Test Circuit 1 *1 ON / OFF VSS Set to VIN or + A GND Figure 11 VOUT VIN SSC Test Circuit 2 + A *1 V ON / OFF + VSS Set to ON Figure 12 VOUT VIN + *1. SSC A Test Circuit 3 *1 V ON / OFF VSS Figure 13 Test Circuit 4 + RL S-19243xxxA Series E / F / G / H type only. 19 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series VOUT VIN SSC *1 V ON / OFF + RL VSS Set to ON Figure 14 VOUT VIN SSC Test Circuit 5 A + *1 ON / OFF V + VSS Set to GND Figure 15 VIN Test Circuit 6 + VOUT V ON / OFF VSS Set to ON Figure 16 *1. 20 Test Circuit 7 S-19243xxxA Series E / F / G / H type only. + Oscilloscope A AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. Types in which output voltage is externally set (S-19243x00, HSOP-8A, HSOP-6, HSNT-8(2030)) SSC + VOUT VIN *1 ON / OFF VADJ V A + VSS Set to ON Figure 17 VOUT VIN SSC Test Circuit 8 *1 ON / OFF VADJ VSS Set to VIN or + A GND Figure 18 VOUT VIN SSC Test Circuit 9 *1 ON / OFF VADJ + A V + VSS Set to ON + Figure 19 Test Circuit 10 VIN VOUT SSC A *1 ON / OFF Figure 20 *1. VADJ VSS V + RL Test Circuit 11 S-19243xxxA Series E / F / G / H type only. 21 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series VOUT VIN SSC *1 ON / OFF VADJ V + RL VSS Set to ON Figure 21 Test Circuit 12 VIN VOUT SSC *1 ON / OFF VADJ A + V + VSS Set to GND Figure 22 Test Circuit 13 VIN VOUT VADJ ON / OFF + V Oscilloscope A + VSS Set to ON Figure 23 Test Circuit 14 VIN VOUT SSC *1 ON / OFF VADJ VSS Set to ON Figure 24 *1. 22 + Test Circuit 15 S-19243xxxA Series E / F / G / H type only. V + A AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Standard Circuits 1. Types in which output voltage is internally set 1. 1 S-19243xxxA Series A / B / C / D type (HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030)) Input VIN CIN*1 Output VOUT CL ON / OFF *2 VSS GND Single GND *1. *2. CIN is a capacitor for stabilizing the input. CL is a capacitor for stabilizing the output. Figure 25 1. 2 S-19243xxxA Series E / F / G / H type (TO-252-5S(A), HSOP-8A, HSOP-6, SOT-89-5, HSNT-8(2030)) Input VIN CIN*1 Output VOUT ON / OFF CL SSC CSS *2 *3 VSS Single GND *1. *2. *3. GND CIN is a capacitor for stabilizing the input. CL is a capacitor for stabilizing the output. CSS is a capacitor for soft-start. Figure 26 Caution The above connection diagram and constants will not guarantee successful operation. Perform thorough evaluation including the temperature characteristics with an actual application to set the constants. 23 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 2. Types in which output voltage is externally set 2. 1 S-19243xxxA Series A / B / C / D type (HSOP-6) Input VIN CIN *1 Output VOUT Ra *3 Rb *3 CL VADJ ON / OFF *2 VSS GND Single GND *1. *2. *3. CIN is a capacitor for stabilizing the input. CL is a capacitor for stabilizing the output. Ra and Rb are resistors for output voltage external setting. Figure 27 2. 1 S-19243xxxA Series E / F / G / H type (HSOP-8A, HSNT-8(2030)) Input VIN CIN *1 ON / OFF VSS Ra *4 Rb *4 CL VADJ *2 SSC Single GND *1. *2. *3. *4. Output VOUT CSS *3 GND CIN is a capacitor for stabilizing the input. CL is a capacitor for stabilizing the output. CSS is a capacitor for soft-start. Ra and Rb are resistors for output voltage external setting. Figure 28 Caution The above connection diagram and constants will not guarantee successful operation. Perform thorough evaluation including the temperature characteristics with an actual application to set the constants. 24 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Condition of Application Input capacitor (CIN): Output capacitor (CL): A ceramic capacitor with capacitance of 2.2 F or more is recommended. A ceramic capacitor with capacitance of 2.2 F or more is recommended. Caution Generally, in a voltage regulator, an oscillation may occur depending on the selection of the external parts. Perform thorough evaluation including the temperature characteristics with an actual application using the above capacitors to confirm no oscillation occurs. Selection of Input Capacitor (CIN) and Output Capacitor (CL) The S-19243xxxA Series requires CL between the VOUT pin and the VSS pin for phase compensation. The operation is stabilized by a ceramic capacitor with capacitance of 2.2 F or more. When using an OS capacitor, a tantalum capacitor or an aluminum electrolytic capacitor, the capacitance also must be 2.2 F or more. However, an oscillation may occur depending on the equivalent series resistance (ESR). Moreover, the S-19243xxxA Series requires CIN between the VIN pin and the VSS pin for a stable operation. Generally, an oscillaiton may occur when a voltage regulator is used under the conditon that the impedance of the power supply is high. Note that the output voltage transient characteristics varies depending on the capacitance of CIN and CL and the value of ESR. Caution Perform thorough evaluation including the temperature characteristics with an actual application to select CIN and CL. Selection of Capacitor for Soft-start (CSS) The S-19243xxxA Series E / F / G / H type requires the capacitor for soft-start (CSS) between the SSC pin and the VSS pin. Over the entire temperature range, the S-19243xxxA Series operates stably with a ceramic capacitor of 0.68 nF or more. According to CSS capacitance, the rising speed of the output voltage is adjustable. The time that the output voltage rises to 99% is 6.0 ms typ. at CSS = 10 nF. The recommended value for applications is 0.68 nF CSS 168 nF, however; define the values by sufficient evaluation including the temperature characteristics under the usage condition. Selection of Resistor for Output Voltage External Setting (Ra, Rb) The S-19243xxxA Series provides the types in which output voltage can be set via the external resistor. The output voltage can be set by connecting a resistor (Ra) between the VOUT pin and the VADJ pin, and a resistor (Rb) between the VADJ pin and the VSS pin. Depending on the intended output voltage, select Ra and Rb from the range shown in Table 27. Caution Since the VADJ pin impedance is comparatively high and is easily affected by noise, pay adequate attention to the wiring pattern. Table 27 VOUT 1.0 V 1.05 V to 9.0 V Ra Connect to VOUT pin 0.1 k to 1.2 M Rb Unnecessary 2 k to 200 k 25 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Explanation of Terms 1. Low dropout voltage regulator This is a voltage regulator which made dropout voltage small by its built-in low on-resistance output transistor. 2. Output voltage (VOUT) This voltage is output at an accuracy of 2.3% when the input voltage, the output current and the temperature are *1 in a certain condition . *1. Differs depending on the product. Caution 3. If the certain condition is not satisfied, the output voltage may exceed the accuracy range of 2.3%. Refer to " Electrical Characteristics" and " Characteristics (Typical Data)" for details. VOUT1 VIN * VOUT Line regulation Indicates the dependency of the output voltage against the input voltage. That is, the value shows how much the output voltage changes due to a change in the input voltage after fixing output current constant. 4. Load regulation (VOUT2) Indicates the dependency of the output voltage against the output current. That is, the value shows how much the output voltage changes due to a change in the output current after fixing input voltage constant. 5. Dropout voltage (Vdrop) Indicates the difference between input voltage (VIN1) and the output voltage when the output voltage becomes 98% of the output voltage value (VOUT3) at VIN = VOUT(S) + 1.0 V after the input voltage (VIN) is decreased gradually. Vdrop = VIN1 - (VOUT3 x 0.98) 26 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Operation 1. Basic operation Figure 29 shows the block diagram of the S-19243xxxA Series to describe the basic operation. The error amplifier compares the feedback voltage (Vfb) whose output voltage (VOUT) is divided by the feedback resistors (Rs and Rf) with the reference voltage (Vref). The error amplifier controls the output transistor, consequently, the regulator starts the operation that keeps VOUT constant without the influence of the input voltage (VIN). VIN *1 Current supply VOUT Error amplifier Vref - + Rf Vfb Reference voltage circuit Rs VSS *1. Parasitic diode Figure 29 2. Output transistor In the S-19243xxxA Series, a low on-resistance P-channel MOS FET is used between the VIN pin and the VOUT pin as the output transistor. In order to keep VOUT constant, the on-resistance of the output transistor varies appropriately according to the output current (IOUT). Caution Since a parasitic diode exists between the VIN pin and the VOUT pin due to the structure of the transistor, the IC may be damaged by a reverse current if VOUT becomes higher than VIN. Therefore, be sure that VOUT does not exceed VIN + 0.3 V. 27 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 3. ON / OFF pin The ON / OFF pin controls the internal circuit and the output transistor in order to start and stop the regulator. When the ON / OFF pin is set to OFF, the internal circuit stops operating and the output transistor between the VIN pin and the VOUT pin is turned off, reducing current consumption significantly. Note that the current consumption increases when a voltage of 0.6 V to VIN - 0.3 V is applied to the ON / OFF pin. The ON / OFF pin is configured as shown in Figure 30 and Figure 31. 3. 1 S-19243xxxA Series A / C / E / G type Since the ON / OFF pin is internally pulled down to the VSS pin in the floating status, the VOUT pin is set to the VSS level. Refer to " Electrical Characteristics" for the ON / OFF pin current. 3. 2 S-19243xxxA Series B / D / F / H type Since the ON / OFF pin is neither pulled down nor pulled up, do not use these types in the floating status. When not using the ON / OFF pin, connect it to the VIN pin. Table 28 Product Type ON / OFF Pin Internal Circuit VOUT Pin Voltage Current Consumption A/B/C/D *1 Constant value ISS1*2 "H" : ON Operate E/F/G/H A/B/C/D Pulled down to VSS*3 "L" : OFF Stop ISS2 E/F/G/H *1. The constant value is output due to the regulating based on the set output voltage value. *2. Note that the IC's current consumption increases as much as current flows into the pull-down resistor when the ON / OFF pin is connected to the VIN pin and the S-19243xxxA Series A / C / E / G type is operating (refer to Figure 30). *3. The VOUT pin voltage of the S-19243xxxA Series A / B / E / F type is pulled down to VSS due to the discharge shunt circuit (RLOW = 100 typ.), the feedback resistors (Rs and Rf) and a load. VIN ON / OFF ON / OFF VSS Figure 30 S-19243xxxA Series A / C / E / G type 28 VIN VSS Figure 31 S-19243xxxA Series B / D / F / H type AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 4. Discharge shunt function (S-19243xxxA Series A / B / E / F type) The S-19243xxxA Series A / B / E / F type has a built-in discharge shunt circuit to discharge the output capacitance. The output capacitance is discharged as follows so that the VOUT pin reaches the VSS level. (1) The ON / OFF pin is set to OFF level. (2) The output transistor is turned off. (3) The discharge shunt circuit is turned on. (4) The output capacitor discharges. Since the S-19243xxxA Series C / D / G / H type does not have a discharge shunt circuit, the VOUT pin is set to the VSS level through several hundred k internal divided resistors between the VOUT pin and the VSS pin. The S-19243xxxA Series A / B / E / F type allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit. S-19243xxxA Series Output transistor: OFF *1 VOUT VIN Discharge shunt circuit : ON *1 ON / OFF ON / OFF circuit Output capacitor (CL) ON / OFF pin: OFF Current flow GND VSS *1. Parasitic diode Figure 32 5. Pull-down resistor (S-19243xxxA Series A / C / E / G type) The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS level. Note that the IC's current consumption increases as much as current flows into the pull-down resistor of 4.0 M typ. when the ON / OFF pin is connected to the VIN pin. 29 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 6. Overcurrent protection circuit The S-19243xxxA Series has a built-in overcurrent protection circuit to limit the overcurrent of the output transistor. When the VOUT pin is shorted to the VSS pin, that is, at the time of the output short-circuit, the output current is limited to 240 mA typ. due to the overcurrent protection circuit operation. The S-19243xxxA Series restarts regulating when the output transistor is released from the overcurrent status. Caution 7. This overcurrent protection circuit does not work as for thermal protection. For example, when the output transistor keeps the overcurrent status long at the time of output short-circuit or due to other reasons, pay attention to the conditions of the input voltage and the load current so as not to exceed the power dissipation. Thermal shutdown circuit The S-19243xxxA Series has a built-in thermal shutdown circuit to limit overheating. When the junction temperature increases to 170C typ., the thermal shutdown circuit becomes the detection status, and the regulating is stopped. When the junction temperature decreases to 135C typ., the thermal shutdown circuit becomes the release status, and the regulator is restarted. If the thermal shutdown circuit becomes the detection status due to self-heating, the regulating is stopped and VOUT decreases. For this reason, the self-heating is limited and the temperature of the IC decreases. The thermal shutdown circuit becomes release status when the temperature of the IC decreases, and the regulating is restarted after the soft-start operation is finished, thus the self-heating is generated again. Repeating this procedure makes the waveform of VOUT into a pulse-like form. This phenomenon continues unless decreasing either or both of the input voltage and the output current in order to reduce the internal power consumption, or decreasing the ambient temperature. Note that the product may suffer physical damage such as deterioration if the above phenomenon occurs continuously. Caution When the heat radiation of the application is not in a good condition, the self-heating cannot be limited immediately, and the IC may suffer physical damage. Perform thorough evaluation with an actual application to confirm no problems happen. Table 29 Thermal Shutdown Circuit VOUT Pin Voltage Release: 135C typ.*1 Constant value*2 Detection: 170C typ.*1 Pulled down to VSS*3 *1. Junction temperature *2. The constant value is output due to the regulating based on the set output voltage value. *3. The VOUT pin voltage is pulled down to VSS due to the feedback resistors (Rs and Rf) and a load. 30 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 8. Soft-start function The S-19243xxxA Series has the built-in soft-start circuit to suppress the inrush current and overshoot of the output voltage generated at power-on or at the time when the ON / OFF pin is set to ON. The soft-start time (tSS) is the time period from when the output voltage rises slowly immediately after power-on or when the ON / OFF pin is set to ON until when the output voltage rises to 99%. Input voltage (VIN, VON / OFF) VIN SSC pin voltage*1 (VSSC) VOUT(E) x 0.99 Output voltage (VOUT(E)) Soft-start time (tSS) t [ms] *1. S-19243xxxA Series E / F / G / H type only. Figure 33 31 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 8. 1 S-19243xxxA Series A / B / C / D type By charging the built-in capacitor via the built-in constant current source, tSS = 1.0 ms typ. is generated. 8. 2 S-19243xxxA Series E / F / G / H type tSS can be adjusted by the external capacitor (CSS) connected between the SSC pin and the VSS pin, and is calculated by using the following calculation. tSS [ms] = Soft-start coefficient*1 [ms / nF] x CSS [nF] + tD0*2 [ms] *1. It is determined by charging the built-in constant current (approx. 2.1 A) to CSS. *2. The delay time of internal capacitance. When the CSS value is sufficiently large, the tD0 value can be disregarded. When the ON / OFF pin is set to OFF, the electrical charge charged in CSS is discharged by the transistor of the discharge shunt circuit. Table 30 Operation Temperature Min. Typ. Max. Tj = +150C 0.391 0.528 0.691 Tj = +125C 0.393 0.534 0.690 Tj = +25C 0.436 0.574 0.704 Tj = -40C 0.467 0.604 0.717 Table 31 Delay Time of Internal Capacitnace (tD0) Operation Temperature Tj = -40C to +150C Caution 32 Soft-start Coefficient [ms / nF] Min. Typ. Max. 0.032 ms 0.047 ms 0.108 ms The above calculation will not guarantee successful operation. Perform thorough evaluation using the actual application including the temperature characteristics under the actual usage conditions to determine CSS capacitance. Refer to " Condition of Application" and " Characteristics (Typical Data)" for details. AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 9. Types in which output voltage is externally set The S-19243xxxA Series provides the types in which output voltage can be set via the external resistor. The output voltage can be set by connecting a resistor (Ra) between the VOUT pin and the VADJ pin, and a resistor (Rb) between the VADJ pin and the VSS pin. The output voltage is determined by the following formulas. VOUT = 1.0 + Ra x la ******************** (1) By substituting Ia = IVADJ + 1.0 / Rb to above formula (1), VOUT = 1.0 + Ra x (IVADJ + 1.0 / Rb) = 1.0 x (1.0 + Ra / Rb) + Ra x IVADJ ******* (2) In above formula (2), Ra x IVADJ is a factor for the output voltage error. Whether the output voltage error is minute is judged depending on the following (3) formula. By substituting IVADJ = 1.0 / RVADJ to Ra x IVADJ VOUT = 1.0 x (1.0 + Ra / Rb) + 1.0 x Ra / RVADJ **************** (3) If RVADJ is sufficiently larger than Ra, the error is judged as minute. VOUT Ia VIN IVADJ VADJ RVADJ Ra VOUT 1.0 V Ib Rb VSS Figure 34 The following expression is in order to determine VOUT = 6.0 V. If Rb = 2 k, substitute RVADJ = 600 k typ. into (3), Ra = (6.0 / 1.0 - 1) x ((2 k x 600 k) / (2 k + 600 k)) 9.97 k Caution The above connection diagrams and constants will not guarantee successful operation. Perform thorough evaluation using the actual application to set the constants. 33 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Precautions * Generally, when a voltage regulator is used under the condition that the load current value is small (1 mA or less), the output voltage may increase due to the leakage current of an output transistor. * Generally, when a voltage regulator is used under the condition that the temperature is high, the output voltage may increase due to the leakage current of an output transistor. * Generally, when the ON / OFF pin is used under the condition of OFF, the output voltage may increase due to the leakage current of an output transistor. * Generally, when a voltage regulator is used under the condition that the impedance of the power supply is high, an oscillation may occur. Perform thorough evaluation including the temperature characteristics with an actual application to select CIN. * Generally, in a voltage regulator, an oscillation may occur depending on the selection of the external parts. The following use conditions are recommended in the S-19243xxxA Series; however, perform thorough evaluation including the temperature characteristics with an actual application to select CIN and CL. Input capacitor (CIN): A ceramic capacitor with capacitance of 2.2 F or more is recommended. Output capacitor (CL): A ceramic capacitor with capacitance of 2.2 F or more is recommended. * Generally, in a voltage regulator, the values of an overshoot and an undershoot depending on the variation factors of input voltage start-up, input voltage fluctuation, capacitance of CIN or CL and the value of the equivalent series resistance (ESR), which stable operation. Perform thorough evaluation including the temperature characteristics select CIN and CL. in the output voltage vary load fluctuation etc., or the may cause a problem to the with an actual application to * Generally, in a voltage regulator, an overshoot may occur in the output voltage momentarily if the input voltage steeply changes when the input voltage is started up, the soft-start operation is performed, the input voltage fluctuates, etc. Perform thorough evaluation including the temperature characteristics with an actual application to confirm no problems happen. * Generally, in a voltage regulator, if the VOUT pin is steeply shorted with GND, a negative voltage exceeding the absolute maximum ratings may occur in the VOUT pin due to resonance phenomenon of the inductance and the capacitance including CL on the application. The resonance phenomenon is expected to be weakened by inserting a series resistor into the resonance path, and the negative voltage is expected to be limited by inserting a protection diode between the VOUT pin and the VSS pin. * If the input voltage is started up steeply under the condition that the capacitance of CL is large, the thermal shutdown circuit may be in the detection status by self-heating due to the charge current to CL. * Make sure of the conditions for the input voltage, output voltage and the load current so that the internal loss does not exceed the power dissipation. * Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. * When considering the output current value that the IC is able to output, make sure of the output current value specified in Table 25 and Table 26 in " Electrical Characteristics" and footnote *5 of the table. * Wiring patterns on the application related to the VIN pin, the VOUT pin and the VSS pin should be designed so that the impedance is low. When mounting CIN between the VIN pin and the VSS pin and CL between the VOUT pin and the VSS pin, connect the capacitors as close as possible to the respective destination pins of the IC. * When setting the output voltage by using an external resistor, connect a resistor (Ra) between the VOUT pin and the VADJ pin and a resistor (Rb) between the VADJ pin and the VSS pin close to the respective pins. * In the package equipped with heat sink of backside, mount the heat sink firmly. Since the heat radiation differs according to the condition of the application, perform thorough evaluation with an actual application to confirm no problems happen. * ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 34 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Characteristics (Typical Data) Output voltage vs. Output current (When load current increases) (Ta = +25C) VOUT = 1.0 V VOUT [V] 1. 1 1. 2 3.6 1.0 3.0 0.8 VIN = 2.5 V 0.6 VIN = 3.0 V 0.4 0.2 VIN = 3.5 V VIN = 4.0 V VIN = 5.0 V 2.4 1.8 1.2 0.6 0.0 0.0 0 1. 3 VOUT = 3.0 V 1.2 VOUT [V] 1. 200 400 600 IOUT [mA] 800 0 1000 200 400 600 IOUT [mA] 800 1000 VOUT = 6.0 V 7.2 VOUT [V] 6.0 VIN = 6.5 V VIN = 7.0 V VIN = 8.0 V 4.8 3.6 2.4 1.2 0.0 0 Remark 200 400 600 800 1000 IOUT [mA] In determining the output current, attention should be paid to the following. 1. The minimum output current value and footnote *5 of Table 25 and Table 26 in " Electrical Characteristics" 2. Power dissipation Output voltage vs. Input voltage (Ta = +25C) VOUT [V] 2. 1 VOUT = 1.0 V 2. 2 3.1 1.0 3.0 0.9 2.9 0.8 IOUT = 1 mA IOUT = 50 mA IOUT = 100 mA 0.7 0.6 IOUT = 1 mA IOUT = 50 mA IOUT = 100 mA 2.8 2.7 2.6 0.5 2.5 0 2. 3 VOUT = 3.0 V 1.1 VOUT [V] 2. 1 2 3 4 5 6 VIN [V] 7 8 9 10 2 3 4 5 6 7 VIN [V] 8 9 10 VOUT = 6.0 V 6.1 VOUT [V] 6.0 5.9 5.8 5.7 IOUT = 1 mA IOUT = 50 mA IOUT = 100 mA 5.6 5.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 VIN [V] 35 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 3. Dropout voltage vs. Output current 3. 1 VOUT = 3.0 V 3. 2 0.40 0.40 Tj = +150C Tj = +125C Tj = +25C Tj = 40C 0.20 0.10 0 100 200 300 400 IOUT [mA] 500 Vdrop [V] VOUT = 3.0 V 4. 2 0 100 200 300 400 IOUT [mA] 500 600 0.30 0.25 0.25 0.20 IOUT = 300 mA 0.15 0.10 IOUT = 30 mA 0.00 -40 -25 0 25 50 75 100 125 150 Tj [C] 0.40 0.30 0.20 IOUT = 500 mA IOUT = 300 mA IOUT = 10 mA 0.10 0.00 2.5 3.0 3.5 4.0 4.5 VOUT [V] 5.0 5.5 0.20 IOUT = 300 mA 0.15 0.10 IOUT = 30 mA 0.05 Dropout voltage vs. Set output voltage (Ta = +25C) Vdrop [V] VOUT = 6.0 V 0.30 0.05 36 0.00 600 Dropout voltage vs. Junction temperature 4. 1 5. 0.20 0.10 Vdrop [V] 4. Tj = +150C Tj = +125C Tj = +25C Tj = 40C 0.30 Vdrop [V] Vdrop [V] 0.30 0.00 VOUT = 6.0 V 6.0 0.00 -40 -25 0 25 50 75 100 125 150 Tj [C] AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 6. Output voltage vs. Junction temperature 6. 1 VOUT = 1.0 V 6. 2 VOUT = 3.0 V VIN = 2.5 V VIN = 4.0 V 3.30 3.20 1.05 VOUT [V] VOUT [V] 1.10 1.00 0.95 3.00 2.90 2.80 0.90 -40 -25 6. 3 3.10 0 25 2.70 -40 -25 50 75 100 125 150 Tj [C] 0 25 50 75 100 125 150 Tj [C] VOUT = 6.0 V VIN = 7.0 V VOUT [V] 6.60 6.30 6.00 5.70 5.40 -40 -25 25 50 75 100 125 150 Tj [C] Current consumption during operation vs. Input voltage (When ON / OFF pin is ON, no load) ISS1 [A] 7. 1 VOUT = 1.0 V 7. 2 160 120 120 Tj = 40C Tj = 25C Tj = 125C Tj = 150C 80 40 0 7. 3 VOUT = 3.0 V 160 ISS1 [A] 7. 0 0 1 2 3 4 5 6 VIN [V] Tj = 40C 80 Tj = 25C Tj = 125C Tj = 150C 40 7 8 9 10 8 9 10 0 0 1 2 3 4 5 6 VIN [V] 7 8 9 10 VOUT = 6.0 V 160 Tj = 150C ISS1 [A] 120 Tj = 125C 80 Tj = 25C 40 0 Tj = 40C 0 1 2 3 4 5 6 VIN [V] 7 37 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 8. Current consumption during operation vs. Junction temperature 8. 1 VOUT = 1.0 V 8. 2 VOUT = 3.0 V VIN = 4.0 V 160 160 120 120 ISS1 [A] ISS1 [A] VIN = 2.5 V 80 40 40 0 -40 -25 8. 3 80 0 25 0 -40 -25 50 75 100 125 150 Tj [C] 0 25 50 75 100 125 150 Tj [C] VOUT = 6.0 V VIN = 7.0 V 160 ISS1 [A] 120 80 40 0 -40 -25 0 25 50 75 100 125 150 Tj [C] Current consumption during operation vs. Output current (Ta = +25C) 9. 9. 1 VOUT = 1.0 V 9. 2 VOUT = 3.0 V 300 250 250 200 200 150 100 50 100 200 300 400 IOUT [mA] 500 600 VOUT = 6.0 V VIN = 7.0 V 300 250 ISS1 [A] 100 0 0 200 150 100 50 0 0 38 150 50 0 9. 3 VIN = 4.0 V 300 ISS1 [A] ISS1 [A] VIN = 2.5 V 100 200 300 400 IOUT [mA] 500 600 0 100 200 300 400 IOUT [mA] 500 600 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 10. 10. 1 Ripple rejection (Ta = +25C) VOUT = 1.0 V 10. 2 VOUT = 3.0 V 100 IOUT = 1 mA IOUT = 30 mA IOUT = 100 mA 80 60 40 20 0 10 10. 3 100 1k 10k Frequency [Hz] 100k VIN = 4.0 V, CL = 2.2 F Ripple Rejection [dB] Ripple Rejection [dB] VIN = 3.0 V, CL = 2.2 F 1M 100 IOUT = 1 mA IOUT = 30 mA IOUT = 100 mA 80 60 40 20 0 10 100 1k 10k Frequency [Hz] 100k 1M VOUT = 6.0 V Ripple Rejection [dB] VIN = 7.0 V, CL = 2.2 F 100 IOUT = 1 mA IOUT = 30 mA IOUT = 100 mA 80 60 40 20 0 10 100 1k 10k Frequency [Hz] 100k 1M 39 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Reference Data Characteristics of input transient response (Ta = +25C) 0.0 1.05 1.00 -2.0 VOUT 0.95 -200 3.15 2.0 VIN 0 VIN [V] VOUT [V] 1.10 200 400 600 t [s] 800 1000 1200 -4.0 1. 3 VOUT = 6.0 V IOUT = 100 mA, CL = 2.2 F, VIN = 7.0 V 8.0 V, tr = tf = 5.0 s 6.40 9.0 8.0 6.0 6.10 6.00 5.0 VOUT 5.90 -200 40 7.0 VIN 4.0 0 200 400 600 t [s] 800 1000 1200 VIN [V] VOUT [V] 6.30 6.20 1. 2 VOUT = 3.0 V IOUT = 100 mA, CL = 2.2 F, VIN = 4.0 V 5.0 V, tr = tf = 5.0 s 6.0 3.20 3.10 4.0 VIN 2.0 0.0 3.05 3.00 -2.0 VOUT 2.95 -4.0 2.90 -200 -6.0 0 200 400 600 t [s] 800 1000 1200 VIN [V] 1. 1 VOUT = 1.0 V IOUT = 100 mA, CL = 2.2 F, VIN = 2.5 V 3.5 V, tr = tf = 5.0 s 1.15 4.0 VOUT [V] 1. AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Characteristics of load transient response (Ta = +25C) 2. 1 VOUT = 1.0 V VIN = 2.5 V, CL = 2.2 F, IOUT = 50 mA 100 mA 1.20 150 0.95 0 200 400 600 t [s] 800 1000 1200 3.05 3.00 -150 0.80 -200 3.30 50 3.20 -50 3.00 2.80 -200 6.05 IOUT 100 6.50 50 6.30 0 VOUT 6.00 -50 5.95 -100 5.90 -200 0 200 400 600 t [s] -200 0 200 400 600 t [s] -600 800 1000 1200 VIN = 7.0 V, CL = 2.2 F, IOUT = 100 mA 500 mA 6.70 600 IOUT [mA] 6.15 6.10 0 -400 2.90 800 1000 1200 -600 800 1000 1200 200 VOUT -100 2. 3 VOUT = 6.0 V VIN = 7.0 V, CL = 2.2 F, IOUT = 50 mA 100 mA 6.20 150 VOUT [V] 3.10 -150 400 600 t [s] 400 600 t [s] IOUT 2.90 -200 200 200 400 2.95 0 0 VIN = 4.0 V, CL = 2.2 F, IOUT = 100 mA 500 mA 3.40 600 100 0 VOUT -200 -400 0.90 IOUT [mA] VOUT [V] 3.10 IOUT 0 VOUT -100 2. 2 VOUT = 3.0 V VIN = 4.0 V, CL = 2.2 F, IOUT = 50 mA 100 mA 3.20 150 3.15 1.00 200 IOUT IOUT [mA] -50 1.10 IOUT [mA] 1.20 0 VOUT 0.90 -200 50 400 -150 800 1000 1200 6.10 400 200 IOUT VOUT 0 5.90 -200 5.70 -400 5.50 -200 0 200 400 600 t [s] IOUT [mA] 1.00 1.30 VOUT [V] 1.05 100 VOUT [V] 1.10 IOUT IOUT [mA] VOUT [V] 1.15 VIN = 2.5 V, CL = 2.2 F, IOUT = 100 mA 500 mA 1.40 600 VOUT [V] 2. -600 800 1000 1200 41 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 3. Transient response characteristics of ON / OFF pin (Ta = +25C) (S-19243xxxA Series A / B / C / D type) VOUT = 1.0 V VIN = 2.5 V, CIN = CL = 2.2 F, IOUT = 100 mA, VON / OFF = 0 V 2.5 V 5.00 3.0 4.00 2.0 3.00 1.0 2.00 0.0 0.00 2.0 VOUT 1.00 400 400 800 4.0 6.00 2.0 4.00 2.00 0.00 3.0 0 0.0 VON / OFF 2.0 4.0 VOUT 2.00 400 1200 1600 2000 6.0 0 400 t [s] 800 t [s] 9.0 16.00 6.0 12.00 3.0 8.00 4.00 0.00 0.0 VON / OFF 3.0 6.0 VOUT 4.00 400 VON / OFF [V] 3. 3 VOUT [V] VOUT = 6.0 V VIN = 7.0 V, CIN = CL = 2.2 F, IOUT = 100 mA, VON / OFF = 0 V 7.0 V 20.00 9.0 0 400 800 1200 1600 2000 t [s] 4. Soft-start time vs. Characteristics of operation ambient temperature VIN = 2.5 V, VON / OFF = 0 V 2.5 V (VOUT(S) < 1.5 V), VIN = VOUT + 1.0 V, VON / OFF = 0 V VOUT + 1.0 V (1.5 V VOUT(S)), CIN = CL = 2.2 F, CSS = 10 nF 10.0 tSS [ms] 8.0 VOUT = 1.0 V 6.0 4.0 2.0 0.0 -40 -25 5. VOUT = 6.0 V VOUT = 3.0 V 0 25 50 75 100 125 150 Ta [C] Soft-start time vs. Characteristics of soft-start capacitance (Ta = +25C) tSS [ms] VIN = 2.5 V, VON / OFF = 0 V 2.5 V (VOUT(S) < 1.5 V), VIN = VOUT + 1.0 V, VON / OFF = 0 V VOUT + 1.0 V (1.5 V VOUT(S)), CIN = CL = 2.2 F 100.0 VOUT = 1.0 V 10.0 VOUT = 3.0 V 1.0 VOUT = 6.0 V 0.1 0.1 42 1.0 10.0 CSS [nF] 100.0 1000.0 6.0 8.00 1200 1600 2000 VON / OFF [V] 1.0 VOUT [V] 1.00 VON / OFF VOUT = 3.0 V VIN = 4.0 V, CIN = CL = 2.2 F, IOUT = 100 mA, VON / OFF = 0 V 4.0 V 10.00 3. 2 VON / OFF [V] VOUT [V] 3. 1 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Inrush current characteristics (Ta = +25C) (S-19243xxxA Series E / F / G / H type) VOUT = 1.0 V VOUT 0.00 1.00 600 400 2.00 3.00 400 800 IIN 200 400 800 1200 1600 2000 2400 VOUT 0.00 1.00 800 600 400 2.00 3.00 4000 0 0 1.00 IIN 200 0 0 4000 8000 12000 16000 20000 24000 t [s] t [s] VIN = 4.0 V, IOUT = 100 mA, CL = 2.2 F, CSS = 1 nF 1200 6.00 VON / OFF 1000 4.00 VOUT 800 2.00 VIN = 4.0 V, IOUT = 100 mA, CL = 2.2 F, CSS = 10 nF 1200 6.00 VON / OFF 1000 4.00 VOUT 800 2.00 600 2.00 400 4.00 6.00 400 IIN 200 400 600 2.00 400 4.00 6.00 4000 0 0 0.00 800 1200 1600 2000 2400 IIN 200 0 0 4000 8000 12000 16000 20000 24000 t [s] t [s] VIN = 7.0 V, IOUT = 100 mA, CL = 2.2 F, CSS = 1 nF 1200 8.00 VON / OFF 1000 6.00 VOUT 800 4.00 VIN = 7.0 V, IOUT = 100 mA, CL = 2.2 F, CSS = 10 nF 1200 8.00 VON / OFF 1000 6.00 VOUT 800 4.00 2.00 600 0.00 400 2.00 4.00 400 IIN 200 0 0 400 800 1200 1600 2000 2400 t [s] VOUT, VON / OFF [V] VOUT = 6.0 V IIN [mA] VOUT, VON / OFF [V] 6. 3 IIN [mA] 0.00 VOUT, VON / OFF [V] VOUT = 3.0 V IIN [mA] VOUT, VON / OFF [V] 6. 2 IIN [mA] 1.00 VIN = 2.5 V, IOUT = 100 mA, CL = 2.2 F, CSS = 10 nF 1200 3.00 VON / OFF 1000 2.00 IIN [mA] VOUT, VON / OFF [V] VIN = 2.5 V, IOUT = 100 mA, CL = 2.2 F, CSS = 1 nF 1200 3.00 VON / OFF 1000 2.00 2.00 600 0.00 400 2.00 4.00 4000 IIN IIN [mA] 6. 1 VOUT, VON / OFF [V] 6. 200 0 0 4000 8000 12000 16000 20000 24000 t [s] 43 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series 7. Output capacitance vs. Characteristics of discharge time (Ta = +25C) VIN = 2.5 V, VON / OFF = 2.5 V VSS (VOUT(S) < 1.5 V), VIN = VOUT + 1.0 V, VON / OFF = VOUT + 1.0 V VSS (1.5 V VOUT(S)), IOUT = 1 mA, tf = 1 s 30 25 VOUT(S) = 1.0 V tDSC [ms] 20 VSS 15 VOUT(S) = 3.0 V 10 0 20 40 60 80 CL [F] 100 VOUT 120 VOUT x 10% VIN = 2.5 V, VON / OFF = 2.5 V VSS (VOUT(S) < 1.5 V), VIN = VOUT + 1.0 V, VON / OFF = VOUT + 1.0 V VSS (1.5 V VOUT(S)) Figure 35 S-19243xxxA Series A / B type (with discharge shunt function) 8. tDSC VOUT(S) = 6.0 V 5 0 1 s VON / OFF Figure 36 Measurement Condition of Discharge Time Example of equivalent series resistance vs. Output current characteristics (Ta = +25C) CIN = CL = 2.2 F 100 VIN RESR [] VOUT CIN Stable ON / OFF 0 1.0 S-19243xxxA Series SSC VSS 500 CSS CL *1 RESR IOUT [mA] *1. Figure 37 44 CL: TDK Corporation CGA6M2X8R1E225K (2.2 F) Figure 38 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series Power Dissipation TO-252-5S(A) HSOP-8A Tj = 150C max. E 4 D 3 C 2 B A 1 0 0 25 50 75 100 125 150 Tj = 150C max. 5 Power dissipation (PD) [W] Power dissipation (PD) [W] 5 D 3 C 2 B 1 A 0 175 E 4 0 25 Ambient temperature (Ta) [C] 100 125 150 175 Ambient temperature (Ta) [C] Power Dissipation (PD) Board Power Dissipation (PD) A 1.45 W A 1.20 W B 2.08 W B 1.69 W C 3.29 W C 3.21 W D 4.03 W D 3.38 W 4.46 W E 4.03 W HSOP-6 SOT-89-5 Tj = 150C max. 4 E 3 D 2 B 1 A 0 25 50 75 100 125 150 175 Tj = 150C max. 5 Power dissipation (PD) [W] 5 Power dissipation (PD) [W] 75 Board E 0 50 4 E 3 D 2 B 1 0 A 0 25 Ambient temperature (Ta) [C] 50 75 100 125 150 175 Ambient temperature (Ta) [C] Board Power Dissipation (PD) Board Power Dissipation (PD) A 1.30 W A 1.05 W B C D 1.69 W - 1.49 W - 2.84 W B C D E 3.05 W E 3.57 W 2.72 W 45 AUTOMOTIVE, 125C OPERATION, 10 V INPUT, 500 mA VOLTAGE REGULATOR WITH SOFT-START FUNCTION Rev.3.2_00 S-19243xxxA Series HSNT-8(2030) Tj = 150C max. Power dissipation (PD) [W] 5 E 4 C 3 D 2 B 1 A 0 0 25 50 75 100 125 150 Ambient temperature (Ta) [C] 46 Board Power Dissipation (PD) A 0.69 W B 0.93 W C 3.13 W D 2.98 W E 3.91 W 175 TO-252-5S Test Board (1) Board A ICMountArea Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (3) Board C Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm No. TO252-5S-A-Board-SD-1.0 enlargedview ABLIC Inc. TO-252-5S Test Board (4) Board D ICMountArea Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Thermal via 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Copper foil layer [mm] 1 2 3 4 (5) Board E Copper foil layer [mm] Thermal via 1 2 3 4 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. TO252-5S-A-Board-SD-1.0 ABLIC Inc. HSOP-8A Test Board (1) Board A ICMountArea Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (3) Board C Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. HSOP8A-A-Board-SD-1.0 ABLIC Inc. HSOP-8A Test Board (4) Board D ICMountArea Item Size [mm] Material Number of copper foil layer 1 2 Copper foil layer [mm] 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - Item Size [mm] Material Number of copper foil layer 1 2 Copper foil layer [mm] 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm (5) Board E Thermal via enlargedview No. HSOP8A-A-Board-SD-1.0 ABLIC Inc. HSOP-6 Test Board ICMountArea (1) Board A Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer 2 Copper foil layer [mm] 1 Land pattern and wiring for testing: t0.070 2 3 4 74.2 x 74.2 x t0.070 Thermal via - (2) Board B Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer 4 Land pattern and wiring for testing: t0.070 1 74.2 x 74.2 x t0.035 2 Copper foil layer [mm] 74.2 x 74.2 x t0.035 3 74.2 x 74.2 x t0.070 4 Thermal via - (3) Board D Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer 4 Copper foil layer [mm] 1 2 3 4 Thermal via Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (4) Board E Item Size [mm] Material Number of copper foil layer 1 2 Copper foil layer [mm] 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm No. HSOP6-A-Board-SD-1.0 enlargedview ABLIC Inc. SOT-89-5 Test Board ICMountArea (1) Board A Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer Copper foil layer [mm] 2 1 Land pattern and wiring for testing: t0.070 2 - 3 4 74.2 x 74.2 x t0.070 Thermal via - (2) Board B Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer 4 Copper foil layer [mm] 1 Land pattern and wiring for testing: t0.070 2 74.2 x 74.2 x t0.035 3 74.2 x 74.2 x t0.035 4 74.2 x 74.2 x t0.070 Thermal via - (3) Board D Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer Copper foil layer [mm] 4 2 Pattern for heat radiation: 2000mm2 t0.070 74.2 x 74.2 x t0.035 3 74.2 x 74.2 x t0.035 4 74.2 x 74.2 x t0.070 1 Thermal via - (4) Board E Item Specification Size [mm] 114.3 x 76.2 x t1.6 Material FR-4 Number of copper foil layer Copper foil layer [mm] Thermal via 4 1 Pattern for heat radiation: 2000mm2 t0.070 2 74.2 x 74.2 x t0.035 3 74.2 x 74.2 x t0.035 4 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm No. SOT895-A-Board-SD-1.0 enlargedview ABLIC Inc. HSNT-8(2030) Test Board ICMountArea (1) Board A Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - (3) Board C Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. HSNT8-A-Board-SD-2.0 ABLIC Inc. HSNT-8(2030) Test Board ICMountArea (4) Board D Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Thermal via 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - Item Size [mm] Material Number of copper foil layer Specification 114.3 x 76.2 x t1.6 FR-4 4 Copper foil layer [mm] 1 2 3 4 enlargedview (5) Board E Copper foil layer [mm] Thermal via 1 2 3 4 2 Pattern for heat radiation: 2000mm t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 Number: 4 Diameter: 0.3 mm enlargedview No. HSNT8-A-Board-SD-2.0 ABLIC Inc. 6.50.2 5.8 1.20.1 (5.2) 0.80 0.60.1 0.220.05 1.27 No. VA005-A-P-SD-2.0 TITLE TO-252-5S-A-PKG Dimensions VA005-A-P-SD-2.0 No. ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 +0.1 o1.5 -0.0 0.20.05 o1.70.1 8.00.1 1.50.1 6.90.1 5 1 Feed direction No. VA005-A-C-SD-1.0 TITLE TO-252-5S-A-C a r r i e r T a p e No. VA005-A-C-SD-1.0 ANGLE UNIT mm ABLIC Inc. 60 13.41.0 Enlarged drawing in the central part o210.8 17.41.0 20.5 o130.2 No. VA005-A-R-SD-1.0 TO-252-5S-A-Reel TITLE VA005-A-R-SD-1.0 No. ANGLE UNIT QTY. mm ABLIC Inc. 4,000 6.0 0.8 2.54 1.27 No. VA005-A-L-SD-1.0 TITLE TO-252-5S-A -Land Recommendation No. VA005-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. 5.020.2 8 5 1 4 1.27 3.0 1 0.200.05 8 4 5 0.40.05 No. FH008-A-P-SD-2.0 TITLE HSOP8A-A-PKG Dimensions No. FH008-A-P-SD-2.0 ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 o1.5 +0.1 -0.0 0.30.05 o2.00.05 8.00.1 2.10.1 6.70.1 1 8 4 5 Feed direction No. FH008-A-C-SD-1.0 TITLE HSOP8A-A-Carrier Tape FH008-A-C-SD-1.0 No. ANGLE UNIT mm ABLIC Inc. 17.41.0 13.41.0 Enlarged drawing in the central part o210.8 20.5 o130.2 No. FH008-A-R-SD-1.0 TITLE HSOP8A-A-Reel No. FH008-A-R-SD-1.0 QTY. ANGLE UNIT mm ABLIC Inc. 4,000 0.76 3.2 1.27 1.27 1.27 No. FH008-A-L-SD-1.0 TITLE HSOP8A-A -Land Recommendation No. FH008-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. 5.020.2 6 1 0.40.05 5 4 2 3 0.200.05 1.670.05 1.91 1.91 No. FH006-A-P-SD-2.1 TITLE HSOP6-A-PKG Dimensions No. FH006-A-P-SD-2.1 ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches:40.00.2) 2.00.05 o1.550.05 0.30.05 o2.00.05 8.00.1 2.10.1 6.70.1 1 6 3 4 Feed direction No. FH006-A-C-SD-2.0 TITLE HSOP6-A-Carrier Tape No. FH006-A-C-SD-2.0 ANGLE UNIT mm ABLIC Inc. 60 20.5 13.50.5 Enlarged drawing in the central part o210.8 20.5 o130.2 No. FH006-A-R-S1-1.0 TITLE HSOP6-A-Reel No. FH006-A-R-S1-1.0 ANGLE UNIT QTY. mm ABLIC Inc. 4,000 2.03 0.76 1.91 1.91 No. FH006-A-L-SD-2.0 TITLE HSOP6-A -Land Recommendation No. FH006-A-L-SD-2.0 ANGLE UNIT mm ABLIC Inc. 4.50.1 1.50.1 1.60.2 5 4 0.3 45 1 2 3 1.50.1 1.50.1 0.40.05 0.40.1 0.40.1 0.450.1 No. UP005-A-P-SD-2.0 TITLE SOT895-A-PKG Dimensions No. UP005-A-P-SD-2.0 ANGLE UNIT mm ABLIC Inc. 4.00.1(10 pitches : 40.00.2) o1.5 +0.1 -0 2.00.05 +0.1 o1.5 -0 0.30.05 8.00.1 2.00.1 4.750.1 3 2 1 4 5 Feed direction No. UP005-A-C-SD-2.0 TITLE SOT895-A-Carrier Tape UP005-A-C-SD-2.0 No. ANGLE UNIT mm ABLIC Inc. 16.5max. 13.00.3 Enlarged drawing in the central part (60) (60) No. UP005-A-R-SD-1.1 TITLE SOT895-A-Reel No. UP005-A-R-SD-1.1 ANGLE UNIT QTY. mm ABLIC Inc. 1,000 2.00.1 8 5 (1.70) 1 4 +0.05 0.08 -0.02 0.5 0.230.1 No. PP008-A-P-SD-2.0 The heat sink of back side has different electric potential depending on the product. Confirm specifications of each product. Do not use it as the function of electrode. TITLE DFN-8/HSNT-8-A-PKG Dimensions No. PP008-A-P-SD-2.0 ANGLE UNIT mm ABLIC Inc. +0.1 o1.5 -0 2.00.05 4.00.1 0.250.05 +0.1 o1.0 -0 0.600.05 4.00.1 2.30.05 4 321 5 6 78 Feed direction No. PP008-A-C-SD-1.0 TITLE DFN-8/HSNT-8-A-Carrier Tape No. PP008-A-C-SD-1.0 ANGLE UNIT mm ABLIC Inc. +1.0 9.0 - 0.0 11.41.0 Enlarged drawing in the central part o130.2 (60) (60) No. PP008-A-R-SD-1.0 TITLE DFN-8/HSNT-8-A-Reel No. PP008-A-R-SD-1.0 QTY. ANGLE UNIT mm ABLIC Inc. 5,000 1.6 0.30 0.50 No. PP008-A-L-SD-1.0 TITLE No. DFN-8/HSNT-8-A -Land Recommendation PP008-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. Disclaimers (Handling Precautions) 1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice. 2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of any specific mass-production design. ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use of the information described herein. 3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein. 4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings, operation voltage range and electrical characteristics, etc. ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the products outside their specified ranges. 5. When using the products, confirm their applications, and the laws and regulations of the region or country where they are used and verify suitability, safety and other factors for the intended use. 6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related laws, and follow the required procedures. 7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use. 8. The products are not designed to be used as part of any device or equipment that may affect the human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc. Especially, the products cannot be used for life support devices, devices implanted in the human body and devices that directly affect human life, etc. Prior consultation with our sales office is required when considering the above uses. ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products. 9. Semiconductor products may fail or malfunction with some probability. The user of the products should therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction. The entire system must be sufficiently evaluated and applied on customer's own responsibility. 10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the product design by the customer depending on the intended use. 11. The products do not affect human health under normal use. However, they contain chemical substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be careful when handling these with the bare hands to prevent injuries, etc. 12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used. 13. The information described herein contains copyright information and know-how of ABLIC Inc. The information described herein does not convey any license under any intellectual property rights or any other rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this document described herein for the purpose of disclosing it to a third-party without the express permission of ABLIC Inc. is strictly prohibited. 14. For more details on the information described herein, contact our sales office. 2.2-2018.06 www.ablic.com