General Description
The MAX1132/MAX1133 are 200ksps, 16-bit ADCs.
These serially interfaced ADCs connect directly to
SPI™, QSPI™, and MICROWIRE™ devices without
external logic. They combine an input scaling network,
internal track/hold, clock, a +4.096V reference, and
three general-purpose digital output pins (for external
multiplexer or PGA control) in a 20-pin SSOP package.
The excellent dynamic performance (SINAD 85dB),
high-speed (200ksps), and low power (7.5mA) of these
ADCs, make them ideal for applications such as indus-
trial process control, instrumentation, and medical
applications. The MAX1132 accepts input signals of 0
to +12V (unipolar) or ±12V (bipolar), while the
MAX1133 accepts input signals of 0 to +4.096V (unipo-
lar) or ±4.096V (bipolar). Operating from a single
+4.75V to +5.25V analog supply and a +4.75V to
+5.25V digital supply, power-down modes reduce
current consumption to 1mA at 10ksps and further
reduce supply current to less than 20µA at slower data
rates. A serial strobe output (SSTRB) allows direct con-
nection to the TMS320 family of digital signal proces-
sors. The MAX1132/MAX1133 user can select either the
internal clock, or an external serial-interface clock for
the ADC to perform analog-to-digital conversions.
The MAX1132/MAX1133 feature internal calibration cir-
cuitry to correct linearity and offset errors. On-demand
calibration allows the user to optimize performance.
Three user-programmable logic outputs are provided
for the control of an 8-channel mux or a PGA.
Applications
Industrial Process Control
Industrial I/O Modules
Data-Acquisition Systems
Medical Instruments
Portable and Battery-Powered Equipment
Features
200ksps (Bipolar) and 150ksps (Unipolar)
Sampling ADC
16-Bits, No Missing Codes
1.5LSB INL Guaranteed
85dB (min) SINAD
+5V Single-Supply Operation
Low-Power Operation, 7.5mA (Unipolar Mode)
2.5µA Shutdown Mode
Software-Configurable Unipolar and Bipolar Input
Ranges
0 to +12V and ±12V (MAX1132)
0 to +4.096V and ±4.096V (MAX1133)
Internal or External Reference
Internal or External Clock
SPI/QSPI/MICROWIRE-Compatible Serial Interface
Three User-Programmable Logic Outputs
Small 20-Pin SSOP Package
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
________________________________________________________________ Maxim Integrated Products 1
TOP VIEW
CS
SHDN
RST
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
AGND
AIN
CREF
AVDD
AGND
REFADJ
REF
DIN
DVDD
DGND
SCLK
P2
P1
P0
SSTRB
DGND
12
11
9
10 DOUT
MAX1132
MAX1133
SSOP
Pin Configuration
19-2083; Rev 0; 8/01
EVALUATION KIT
AVAILABLE
Ordering Information
PART TEMP. RANGE PIN-PACKAGE INL
(LSB
)
MAX1132ACAP* 0°C to +70°C 20 SSOP ±1.5
MAX1132BCAP 0°C to +70°C 20 SSOP ±2.5
Functional Diagram appears at end of data sheet.
Typical Application Circuit appears at end of data sheet.
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
Ordering Information continued at end of data sheet.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
AVDD to AGND, DVDD to DGND .............................-0.3V to +6V
AGND to DGND.....................................................-0.3V to +0.3V
AIN to AGND.....................................................................±16.5V
REFADJ, CREF, REF to AGND.................-0.3V to (AVDD + 0.3V)
Digital Inputs to DGND.............................................-0.3V to +6V
Digital Outputs to DGND .........................-0.3V to (DVDD + 0.3V)
Continuous Power Dissipation (TA= +70°C)
20-Pin SSOP (derate 8.00mW/°C above +70°C) .........640mW
Operating Temperature Ranges
MAX113_CAP ......................................................0°C to +70°C
MAX113_EAP....................................................-40°C to +85°C
Storage Temperature Range .............................-60°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external
VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA= +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DC ACCURACY (Note 1)
Resolution 16 Bits
MAX113_A ±1.5
Relative Accuracy (Note 2) INL Bipolar mode MAX113_B ±2.5 LSB
No Missing Codes 16 Bits
MAX113_A -1 +1
Differential Nonlinearity DNL Bipolar mode MAX113_B -1 +1.75 LSB
Transition Noise 0.77 LSBRMS
MAX1132 ±4
Unipolar MAX1133 ±2
MAX1132 ±6
Offset Error
Bipolar MAX1133 ±5
mV
Unipolar ±0.2
Gain Error (Note 3) Bipolar ±0.3 %FSR
Offset D r i ft ( Bi p ol ar and U ni p ol ar ) Excluding reference drift ±1 ppm/oC
G ai n D r i ft ( Bi p ol ar and U ni p ol ar ) Excluding reference drift ±1 ppm/oC
DYNAMIC SPECIFICATIONS (5kHz sine-wave input, 200ksps, 4.8MHz clock, bipolar input mode. MAX1132: 24Vp-p.
MAX1133: 8.192Vp-p)
fIN = 5kHz 85
SINAD fIN = 100kHz 85 dB
fIN = 5kHz 87
SNR fIN = 100kHz 92 dB
fIN = 5kHz -90
THD fIN = 100kHz -92 dB
fIN = 5kHz 92
SFDR fIN = 100kHz 96 dB
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external
VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA= +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ANALOG INPUT
Unipolar 0 12
MAX1132 Bipolar -12 12
Unipolar 0 4.096
Input Range
MAX1133 Bipolar - 4.096 4.096
V
Unipolar 7.5 10.0
MAX1132 Bipolar 5.9 7.9
Unipolar 100 1000
Input Impedance
MAX1133 Bipolar 3.4 4.5
k
Input Capacitance 32 pF
CONVERSION RATE
Internal Clock Frequency 4 MHz
Aperture Delay tAD 10 ns
Aperture Jitter tAS 50 ps
MODE 1 (24 External Clock Cycles per Conversion)
Unipolar 0.1 3
External Clock Frequency fSCLK Bipolar 0.1 4.8 MHz
Unipolar 4.17 125
Sample Rate fS = fSCLK /24 Bipolar 4.17 200 ksps
Unipolar 8 240
Conversion Time (Note 4) tCONV+ACQ =
24 / fSCLK Bipolar 5 240 µs
MODE 2 (Internal Clock Mode)
External Clock Frequency
(Data Transfer Only) 8 MHz
Conversion Time SSTRB low pulse width 4 6 µs
Unipolar 1.82
Acquisition Time Bipolar 1.14 µs
MODE 3 (32 External Clock Cycles per Conversion)
External Clock Frequency fSCLK Unipolar or bipolar 0.1 4.8 MHz
Sample Rate fS = fSCLK /32 Unipolar or bipolar 3.125 150 ksps
Conversion Time (Note 4) tCONV+ACQ =
32 / fSCLK Unipolar or bipolar 6.67 320 µs
INTERNAL REFERENCE
Output Voltage VREF 4.056 4.096 4.136 V
REF Short-Circuit Current 24 mA
Output Tempco ±20 ppm/oC
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external
VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA= +25°C.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Capacitive Bypass at REF 0.47 10 µF
Maximum Capacitive Bypass at
REFADJ 10 µF
REFADJ Output Voltage 4.096 V
REFADJ Input Range For small adjustments from 4.096V ±100 mV
REFADJ Buffer Disable
Threshold To power-down the internal reference AV
D D
-
0.5V
AV
D D
-
0.1V V
Buffer Voltage Gain 1 V/V
EXTERNAL REFERENCE (Reference buffer disabled. Reference applied to REF)
Input Range (Notes 5 and 6) 3.0 4.096 4.2 V
VREF = 4.096V, fSCLK = 4.8MHz 250
VREF = 4.096V, fSCLK = 0 230Input Current
In power-down, fSCLK = 0 0.1
µA
DIGITAL INPUTS
Input High Voltage VIH 2.4 V
Input Low Voltage VIL 0.8 V
Input Leakage IIN VIN = 0 or DVDD ±1 µA
Input Hysteresis VHYST 0.2 V
Input Capacitance CIN 10 pF
DIGITAL OUTPUTS
Output High Voltage VOH ISOURCE = 0.5mA DVDD -
0.5 V
ISINK = 5mA 0.4
Output Low Voltage VOL ISINK = 16mA 0.8 V
Three-State Leakage Current ILCS = DVDD ±10 µA
Three-State Output
Capacitance CS = DVDD 10 pF
POWER SUPPLIES
Analog Supply (Note 7) AVDD 4.75 5 5.25 V
Digital Supply (Note 7) DVDD 4.75 5 5.25 V
Unipolar mode 5 8
Bipolar mode 8.5 11 mA
Analog Supply Current IANALOG
SHDN = 0, or softw are power -down mode 0.3 10 µA
Unipolar or bipolar mode 2.5 3.5 mA
Digital Supply Current IDIGITAL SHDN = 0, or softw are power -down mode 2.2 10 µA
Power-Supply Rejection Ratio
(Note 8) PSRR AVDD = DVDD = 4.75V to 5.25V 72 dB
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
_______________________________________________________________________________________ 5
Note 1: Tested at AVDD = DVDD = +5V, bipolar input mode.
Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the gain error and offset
error have been nulled.
Note 3: Offset nulled.
Note 4: Conversion time is defined as the number of clock cycles multiplied by the clock period, clock has 50% duty cycle.
Includes the acquisition time.
Note 5: ADC performance is limited by the converter’s noise floor, typically 300µVp-p.
Note 6: When an external reference has a different voltage than the specified typical value, the full scale of the ADC will scale
proportionally.
Note 7: Electrical characteristics are guaranteed from AVDD(MIN) = DVDD(MIN) to AVDD(MAX) = DVDD(MAX). For operations beyond
this range, see the Typical Operating Characteristics. For guaranteed specifications beyond the limits, contact the factory.
Note 8: Defined as the change in positive full scale caused by a ±5% variation in the nominal supply voltage.
TIMING CHARACTERISTICS (Figures 5 and 6)
(AVDD = DVDD = +5V ±5%, TA= TMIN to TMAX, unless otherwise noted.)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Acquisition Time tACQ 1.14 µs
DIN to SCLK Setup tDS 50 ns
DIN to SCLK Hold tDH 0ns
SCLK to DOUT Valid tDO 70 ns
CS Fall to DOUT Enable tDV CLOAD = 50pF 80 ns
CS Rise to DOUT Disable tTR CLOAD = 50pF 80 ns
CS to SCLK Rise Setup tCSS 100 ns
CS to SCLK Rise Hold tCSH 0ns
SCLK High Pulse Width tCH 80 ns
SCLK Low Pulse Width tCL 80 ns
SCLK Fall to SSTRB tSSTRB CLOAD = 50pF 80 ns
CS Fall to SSTRB Enable tSDV CLOAD = 50pF, external clock mode 80 ns
CS Rise to SSTRB Disable tSTR CLOAD = 50pF, external clock mode 80 ns
SSTRB Rise to SCLK Rise tSCK Internal clock mode 0 ns
RST Pulse Width tRS 208 ns
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
6 _______________________________________________________________________________________
Typical Operating Characteristics
(MAX1132/MAX1133: AVDD = DVDD = +5V , fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps),
bipolar input, external REF = +4.096V, 0.22µF bypassing on REFADJ, 2.2µF on REF, 1µF on CREF, TA= 25°C, unless otherwise noted.)
-1.5
-1.0
-0.5
0
0.5
1.0
1.5
1 13729
6865 20593
27457
34321
41185
48049
54913
61777
INTEGRAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
MAX1132 toc01
DIGITAL OUTPUT CODE
INTEGRAL NONLINEARITY (LSB)
-1.0
-0.6
-0.8
-0.2
-0.4
0.2
0
0.4
0.8
0.6
1.0
1 13729
20593
27457
6865 34321
41185
48049
54913
61777
DIFFERENTIAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
MAX1132 toc02
DIGITAL OUTPUT CODE
DIFFERENTIAL NONLINEARITY (LSB)
9.5
10.1
9.9
9.7
10.5
10.3
11.3
11.1
10.9
10.7
11.5
-40 -20 020 40 60 80
TOTAL SUPPLY CURRENT
vs. TEMPERATURE
MAX1132 toc03
TEMPERATURE (°C)
TOTAL SUPPLY CURRENT (mA)
A
B
C
A: AVDD, DVDD = +4.75V
B: AVDD, DVDD = +5.00V
C: AVDD, DVDD = +5.25V
-4
-3
-2
-1
0
OFFSET VOLTAGE vs. TEMPERATURE
MAX1132 toc04
TEMPERATURE (°C)
OFFSET VOLTAGE (mV)
-40 20 40-20 0 60 80
A
B
C
A: AVDD, DVDD = +4.75V
B: AVDD, DVDD = +5.00V
C: AVDD, DVDD = +5.25V
0
0.01
0.02
0.03
0.04
GAIN ERROR vs. TEMPERATURE
MAX1132 toc05
TEMPERATURE (°C)
GAIN ERROR (% FULL SCALE)
-40 20 40-20 0 60 80
A
B
C
A: AVDD, DVDD = +4.75V
B: AVDD, DVDD = +5.00V
C: AVDD, DVDD = +5.25V
100
10
1.00
0.10
0.01
0101 100 1000
TOTAL SUPPLY CURRENT vs.
CONVERSION RATE (USING SHUTDOWN)
MAX1132 toc06
CONVERSION RATE (ksps)
TOTAL SUPPLY CURRENT (mA)
0.990
0.995
1.000
1.005
1.010
NORMALIZED REF VOLTAGE
vs. TEMPERATURE
MAX1132 toc07
TEMPERATURE (°C)
NORMALIZED REF VOLTAGE (V)
-40 20 40-20 0 60 80
-120
-100
-80
-40
-60
-20
0
0189 273645546372819099
FFT PLOT
MAX1132 toc08
FREQUENCY (kHz)
AMPLITUDE (dB)
fSAMPLE = 200kHz
fIN = 5kHz
90
0
0.1 100101
SINAD PLOT
30
10
70
50
100
40
20
80
60
MAX1132 toc09
FREQUENCY (kHz)
AMPLITUDE (dB)
fSAMPLE = 200kHz
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
_______________________________________________________________________________________ 7
Typical Operating Characteristics (continued)
(MAX1132/MAX1133: AVDD = DVDD = +5V , fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps),
bipolar input, external REF = +4.096V, 0.22µF bypassing on REFADJ, 2.2µF on REF, 1µF on CREF, TA= 25°C, unless otherwise noted.)
0
0.1 100101
SFDR PLOT
120
MAX1132 toc10
FREQUENCY (kHz)
AMPLITUDE (dB)
100
80
60
40
10
20
30
110
90
70
50
fSAMPLE = 200kHz
-110
0.1 100101
THD PLOT
0
MAX1132 toc11
FREQUENCY (kHz)
AMPLITUDE (dB)
-10
-30
-50
-70
-100
-90
-80
-20
-40
-60
fSAMPLE = 200kHz
PIN NAME FUNCTION
1 REF
Reference Buffer Output/ADC Reference Input. Reference voltage for analog-to-digital conversion. In
internal reference mode, the reference buffer provides a +4.096V nominal output, externally adjustable at
REFADJ. In external reference mode, disable the internal buffer by pulling REFADJ to AVDD. Bypass to
AGND with a 2.2µF capacitor when using the internal reference.
2 REFADJ Bandgap Reference Output/Bandgap Reference Buffer Input. Bypass to AGND with 0.22µF. When using an
external reference, connect REFADJ to AVDD to disable the internal bandgap reference.
3 AGND Analog Ground. This is the primary analog ground (Star Ground).
4AV
DD Analog Supply. 5V ±5%. Bypass AVDD to AGND (pin 3) with a 0.1µF capacitor.
5 DGND Digital Ground
6SHDN Shutdown Control Input. Drive SHDN low to put the ADC in shutdown mode.
7 P2 User-Programmable Output 2
8 P1 User-Programmable Output 1
9 P0 User-Programmable Output 0
10 SSTRB
Serial Strobe Output. In internal clock mode, SSTRB goes low when the ADC begins a conversion and goes
high when the conversion is finished. In external clock mode, SSTRB pulses high for one clock period
before the MSB decision. It is high impedance when CS is high in external clock mode.
11 DOUT Serial Data Output. MSB first, straight binary format for unipolar input, two’s complement for bipolar input.
Each bit is clocked out of DOUT at the falling edge of SCLK.
12 RST Reset Inp ut. D r i ve RST l ow to p ut the d evi ce i n the p ow er - on d efaul t m od e. S ee the P ow er - O n Reset secti on.
Pin Description
MAX1132/MAX1133
Detailed Description
The MAX1132/MAX1133 analog-to-digital converters
(ADCs) use a successive-approximation technique and
input track/hold (T/H) circuitry to convert an analog sig-
nal to a 16-bit digital output. The MAX1132/MAX1133
easily interfaces to microprocessors (µPs). The data
bits can be read either during the conversion in exter-
nal clock mode or after the conversion in internal clock
mode.
In addition to a 16-bit ADC, the MAX1132/MAX1133
include an input scaler, an internal digital microcon-
troller, calibration circuitry, an internal clock generator,
and an internal bandgap reference. The input scaler for
the MAX1132 enables conversion of input signals rang-
ing from 0 to +12V (unipolar input) or ±12V (bipolar
input). The MAX1133 accepts 0 to +4.096V (unipolar
input) or ±4.096V (bipolar input). Input range selection
is software controlled.
Calibration
To minimize linearity, offset, and gain errors, the
MAX1132/MAX1133 have on-demand software calibra-
tion. Initiate calibration by writing a Control-Byte with bit
M1 = 0, and bit M0 = 1 (see Table 1). Select internal or
external clock for calibration by setting the INT/EXT bit
in the Control Byte. Calibrate the MAX1132/MAX1133
with the clock used for performing conversions.
Offsets resulting from synchronous noise (such as the
conversion clock) are canceled by the MAX1132/
MAX1133’s calibration circuitry. However, because the
magnitude of the offset produced by a synchronous
signal depends on the signal’s shape, recalibration
may be appropriate if the shape or relative timing of the
clock or other digital signals change, as might occur if
more than one clock signal or frequency is used.
Input Scaler
The MAX1132/MAX1133 have an input scaler which
allows conversion of true bipolar input voltages while
operating from a single +5V supply. The input scaler
attenuates and shifts the input as necessary to map the
external input range to the input range of the internal
DAC. The MAX1132 analog input range is 0 to +12V
(unipolar) or ±12V (bipolar). The MAX1133 analog input
range is 0 to +4.096V (unipolar) or ±4.096V (bipolar).
Unipolar and bipolar mode selection is configured with
bit 6 of the serial Control Byte.
Figure 1 shows the equivalent input circuit of the
MAX1132/MAX1133. The resistor network on the analog
input provides ±16.5V fault protection. This circuit limits
the current going into or out of the pin to less than 2mA.
The overvoltage protection is active, even if the device
is in a power-down mode, or if AVDD = 0.
Digital Interface
The digital interface pins consist of SHDN, RST, SSTRB,
DOUT, SCLK, DIN and CS. Bringing SHDN low, places
the MAX1132/MAX1133 in its 2.5µA shutdown mode. A
logic low on RST halts the MAX1132/MAX1133 opera-
tion and returns the part to its power-on reset state.
In external clock mode, SSTRB is is low and pulses
high for one clock cycle at the start of conversion. In
internal clock mode, SSTRB goes low at the start of the
conversion and goes high to indicate the conversion is
finished.
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
8 _______________________________________________________________________________________
PIN NAME FUNCTION
13 SCLK Serial Data Clock Input. Serial data on DIN is loaded on the rising edge of SCLK, and serial data is updated
on DOUT on the falling edge of SCLK. In external clock mode, SCLK sets the conversion speed.
14 DGND Digital Ground. Connect to pin 5.
15 DVDD Digital Supply. 5V ±5%. Bypass DVDD to DGND (pin 14) with a 0.1µF capacitor.
16 DIN Serial Data Input. Serial data on DIN is latched on the rising edge of SCLK.
17 CS Chip-Select Input. Drive CS low to enable the serial interface. When CS is high, DOUT is high impedance.
In external clock mode, SSTRB is high impedance when CS is high.
18 CREF Reference Buffer Bypass. Bypass CREF to AGND (pin 3) with 1µF.
19 AGND Analog Ground. Connect pin 19 to pin 3.
20 AIN Analog Input
Pin Description (continued)
The DIN input accepts Control Byte data which is
clocked in on each rising edge of SCLK. After CS goes
low or after a conversion or calibration completes, the
first logic “1” clocked into DIN is interpreted as the
START bit, the MSB of the 8-bit Control Byte.
The SCLK input is the serial data transfer clock which
clocks data in and out of the MAX1132/MAX1133.
SCLK also drives the A/D conversion steps in external
clock mode (see Internal and External Clock Modes
section).
DOUT is the serial output of the conversion result.
DOUT is updated on the falling edge of SCLK. DOUT is
high-impedance when CS is high.
CS must be low for the MAX1132/MAX1133 to accept a
Control Byte. The serial interface is disabled when CS
is high.
User-Programmable Outputs
The MAX1132/MAX1133 have three user-programma-
ble outputs, P0, P1 and P2. The power-on default state
for the programmable outputs is zero. These are push-
pull CMOS outputs suitable for driving a multiplexer, a
PGA, or other signal preconditioning circuitry. The user-
programmable outputs are controlled by bits 0, 1, and
2 of the Control Byte (Table 2).
The user-programmable outputs are set to zero during
power-on reset (POR) or when RST goes low. During
hardware or software shutdown P0, P1, and P2 are
unchanged and remain low-impedance.
Starting a Conversion
Start a conversion by clocking a Control Byte into the
device’s internal shift register. With CS low, each rising
edge on SCLK clocks a bit from DIN into the
MAX1132/MAX1133’s internal shift register. After CS
goes low or after a conversion or calibration completes,
the first arriving logic “1” is defined as the start bit of
the Control Byte. Until this first start bit arrives, any
number of logic “0” bits can be clocked into DIN with
no effect. If at any time during acquisition or conversion,
CS is brought high and then low again, the part is
placed into a state where it can recognize a new start
bit. If a new start bit occurs before the current conver-
sion is complete, the conversion is aborted and a new
acquisition is initiated.
Internal and External Clock Modes
The MAX1132/MAX1133 may use either the external
serial clock or the internal clock to perform the succes-
sive-approximation conversion. In both clock modes,
the external clock shifts data in and out of the
MAX1132/MAX1133. Bit 5 (INT/EXT) of the Control Byte
programs the clock mode.
External Clock
In external clock mode, the external clock not only
shifts data in and out, but it also drives the ADC con-
version steps. In short acquisition mode, SSTRB pulses
high for one clock period after the seventh falling edge
of SCLK following the start bit. The MSB of the conver-
sion is available at DOUT on the eighth falling edge of
SCLK (Figure 2).
In long acquisition mode, when using external clock,
SSTRB pulses high for one clock period after the fif-
teenth falling edge of SCLK following the start bit. The
MSB of the conversion is available at DOUT on the six-
teenth falling edge of SCLK (Figure 3).
In external clock mode, SSTRB is high-impedance
when CS is high. In external clock mode, CS is normally
held low during the entire conversion. If CS goes high
during the conversion, SCLK is ignored until CS goes
low. This allows external clock mode to be used with 8-
bit bytes.
Internal Clock
In internal clock mode, the MAX1132/MAX1133 gener-
ates its own conversion clock. This frees the micro-
processor from the burden of running the SAR conver-
sion clock, and allows the conversion results to be read
back at the processor’s convenience, at any clock rate
up to 8MHz.
SSTRB goes low at the start of the conversion and goes
high when the conversion is complete. SSTRB will be
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
_______________________________________________________________________________________ 9
S1 = BIPOLAR/UNIPOLAR
S2, S3 = T/H SWITCH
S3
S2
AIN
S1
R1
2.5k
R3
R2
VOLTAGE
REFERENCE
T/H OUT
HOLD
HOLD
TRACK
TRACK
BIPOLAR
UNIPOLAR
R2 = 7.6k (MAX1132)
OR 2.5k (MAX1133)
R3 = 3.9k (MAX1132)
OR INFINITY (MAX1133)
CHOLD
30pF
Figure 1. Equivalent Input Circuit
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
10 ______________________________________________________________________________________
Table 1. Control Byte Format
BIT NAME DESCRIPTION
7 (MSB) START The first logic “1” bit, after CS goes low, defines the beginning of the Control Byte
6 UNI/BIP
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, analog
input signals from 0 to +12V (MAX1132) or 0 to VREF (MAX1133) can be converted. In bipolar
mode analog input signals from -12V to +12V (MAX1132) or -VREF to +VREF (MAX1133) can be
converted.
5 INT/EXT Selects the internal or external conversion clock. 1 = Internal, 0 = External.
4M1
M1 M0 MODE
0 0 24 External clocks per conversion (short acquisition mode)
0 1 Start Calibration. Starts internal calibration.
1 0 Software power-down mode
3M0
1 1 32 External clocks per conversion (long acquisition mode)
2
1
0(LSB)
P2
P1
P0
These three bits are stored in a port register and output to pins P2, P1, P0 for use in addressing
a mux or PGA. These three bits are updated in the port register simultaneously when a new
Control Byte is written.
Table 2. User-Programmable Outputs
OUTPUT
PIN
PROGRAMMED
THROUGH
CONTROL BYTE
POWER-ON
OR RST
DEFAULT
DESCRIPTION
P2 Bit 2 0
P1 Bit 1 0
P0 Bit 0 0
U ser - p r og r am m ab l e outp uts fol l ow the state of the C ontr ol Bytes thr ee LS Bs
and ar e up d ated si m ul taneousl y w hen a new C ontr ol Byte i s w r i tten. O utp uts
ar e p ush- p ul l . In har d w ar e and softw ar e shutd ow n, these outp uts ar e
unchang ed and r em ai n l ow - i m p ed ance.
ACQUISITION CONVERSIONIDLE IDLE
SCLK
DOUT
A/D
STATE
DIN
SSTRB
CS
41812
START M1 M0
P2
P1 P0
UNI/
BIP
INT/
EXT
15 21 24
B12 B11B14 B13
B10
B9 B4
B15
MSB
B0
LSB
FILLED WITH
ZEROS
B2B3 B1
tACQ
Figure 2. Short Acquisition Mode (24-Clock Cycles) External Clock, Bipolar Mode
low for a maximum of 6µs, during which time SCLK
should remain low for best noise performance. An inter-
nal register stores data when the conversion is in
progress. SCLK clocks the data out of the internal stor-
age register at any time after the conversion is com-
plete.
The MSB of the conversion is available at DOUT when
SSTRB goes high. The subsequent 15 falling edges on
SCLK shift the remaining bits out of the internal storage
register (Figure 4). CS does not need to be held low
once a conversion is started.
When internal clock mode is selected, SSTRB does not
go into a high-impedance state when CS goes high.
Figure 5 shows the SSTRB timing in internal clock
mode. In internal clock mode, data can be shifted in to
the MAX1132/MAX1133 at clock rates up to 4.8MHz,
provided that the minimum acquisition time, tACQ, is
kept above 1.14µs in bipolar mode and 1.82µs in
unipolar mode. Data can be clocked out at 8MHz.
Output Data
The output data format is straight binary for unipolar
conversions and two’s complement in bipolar mode. In
both modes the MSB is shifted out of the MAX1132/
MAX1133 first.
Data Framing
The falling edge of CS does NOT start a conversion on
the MAX1132/MAX1133. The first logic high clocked into
DIN is interpreted as a start bit and defines the first bit of
the Control Byte. A conversion starts on the falling edge
of SCLK, after the seventh bit of the Control Byte (the P1
bit) is clocked into DIN. The start bit is defined as:
The first high bit clocked into DIN with CS low any-
time the converter is idle, e.g., after AVDD is
applied, or as the first high bit clocked into DIN
after CS is pulsed high, then low.
OR
If a falling edge on CS forces a start bit before the
conversion or calibration is complete, then the
current operation will be terminated and a new
one started.
Applications Information
Power-On Reset
When power is first applied to the MAX1132/MAX1133
or if RST is pulsed low, the internal calibration registers
are set to their default values. The user-programmable
registers (P0, P1, and P2) are low, and the device is
configured for bipolar mode with internal clocking.
Calibration
To compensate the MAX1132/MAX1133 for temperature
drift and other variations, they should be periodically
calibrated. After any change in ambient temperature
more than 10°C the device should be recalibrated. A
100mV change in supply voltage or any change in the
reference voltage should be followed by a calibration.
Calibration corrects for errors in gain, offset, integral
nonlinearity, and differential nonlinearity. The MAX1132/
MAX1133 should be calibrated after power-up or the
assertion of reset. Make sure the power supplies and
the reference voltage have fully settled prior to initiating
the calibration sequence.
Initiate calibration by setting M1 = 0 and M0 = 1 in the
Control-Byte. In internal clock mode, SSTRB goes low at
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________ 11
SCLK
DOUT
A/D
STATE
DIN
SSTRB
CS
41819
START M1 M0
P2
P1 P0
UNI/
BIP
INT/
EXT
15 29 32
B4B14 B13
B3
B2 B1
B15
MSB
B0
LSB
FILLED WITH
ZEROS
tACQ
ACQUISITION CONVERSIONIDLE IDLE
Figure 3. Long Acquisition Mode (32-Clock Cycles) External Clock, Bipolar Mode
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
12 ______________________________________________________________________________________
SCLK
DOUT
DIN
SSTRB
CS
418
START M1 M0
P2
P1 P0
UNI/
BIP
INT/
EXT
921 24
B4B14 B13
B3
B2 B1
B15
MSB
B0
LSB
FILLED WITH
ZEROS
tACQ
tCONV
Figure 4. Internal Clock Mode Timing, Short Acquisition, Bipolar Mode
P0 CLOCK IN
tSSTRB
tCONV
tSCK
tCSS
SSTRB
SCLK
NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION.
tCSH
CS
Figure 5. Internal Clock Mode SSTRB Detailed Timing
tSDV
tSSTRB tSSTRB
tSTR
P1 CLOCKED IN
SSTRB
SCLK
CS
Figure 6. External Clock Mode SSTRB Detailed Timing
the beginning of calibration and goes high to signal the
end of calibration, approximately 80,000 clock cycles
later. In external clock mode, SSTRB goes high at the
beginning of calibration and goes low to signal the end
of calibration. Calibration should be performed in the
same clock mode as will be used for conversions.
Reference
The MAX1132/MAX1133 can be used with an internal
or external reference. An external reference can be
connected directly at the REF pin or at the REFADJ pin.
CREF is an internal reference node and must be
bypassed with a 1µF capacitor when using either the
internal or an external reference.
Internal Reference
When using the MAX1132/MAX1133’s internal refer-
ence, place a 0.22µF ceramic capacitor from REFADJ
to AGND and place a 2.2µF capacitor from REF to
AGND. Fine adjustments can be made to the internal
reference voltage by sinking or sourcing current at
REFADJ. The input impedance of REFADJ is nominally
9k. The internal reference voltage is adjustable to
±1.5% with the circuit of Figure 7.
External reference
An external reference can be placed at either the input
(REFADJ) or the output (REF) of the MAX1132/
MAX1133’s internal buffer amplifier.
When connecting an external reference to REFADJ, the
input impedance is typically 9k. Using the buffered
REFADJ input makes buffering of the external reference
unnecessary, however, the internal buffer output must
be bypassed at REF with a 2.2µF capacitor.
When connecting an external reference at REF,
REFADJ must be connected to AVDD. Then the input
impedance at REF is a minimum of 164kfor DC cur-
rents. During conversion, an external reference at REF
must deliver 250µA DC load current and have an out-
put impedance of 10or less. If the reference has a
higher output impedance or is noisy, bypass it at the
REF pin with a 4.7µF capacitor.
Analog Input
The MAX1132/MAX1133 use a capacitive DAC that
provides an inherent track/hold function. Drive AIN with
a source impedance less than 10. Any signal condi-
tioning circuitry must settle with 16-bit accuracy in less
than 500ns. Limit the input bandwidth to less than half
the sampling frequency to eliminate aliasing. The
MAX1132/MAX1133 has a complex input impedance
which varies from unipolar to bipolar mode (Figure 1).
Input Range
The analog input range in unipolar mode is 0 to +12V
for the MAX1132, and 0 to +4.096V for the MAX1133. In
bipolar mode, the analog input can be -12V to +12V for
the MAX1132, and -4.096V to +4.096V for the
MAX1133. Unipolar and bipolar mode is programmed
with the UNI/BIP bit of the Control Byte. When using a
reference other than the MAX1132/MAX1133’s internal
+4.096V reference, the full-scale input range will vary
accordingly. The full-scale input range depends on the
voltage at REF and the sampling mode selected (Tables
3 and 4).
Input Acquisition and Settling
Clocking in a Control Byte starts input acquisition. In
bipolar mode the main capacitor array starts acquiring
the input as soon as a start bit is recognized. If unipolar
mode is selected by the second DIN bit, the part will
immediately switch to unipolar sampling mode and
acquire a sample.
Acquisition can be extended by eight clock cycles by
setting M1 = 1, M0 = 1 (long acquisition mode). The
sampling instant in short acquisition completes on the
falling edge of the sixth clock cycle after the start bit
(Figure 2).
Acquisition is 5.5 clock cycles in short acquisition
mode and 13.5 clock cycles in long acquisition mode.
Short acquisition mode is 24 clock cycles per conver-
sion. Using the external clock to run the conversion
process limits unipolar conversion speed to 125ksps
instead of 200ksps in bipolar mode. The input resis-
tance in unipolar mode is larger than that of bipolar
mode (Figure1). The RC time constant in unipolar mode
is larger than that of bipolar mode, reducing the maxi-
mum conversion rate in 24 external clock mode. Long
acquisition mode with external clock allows both unipo-
lar and bipolar sampling of 150ksps (4.8MHz/32 clock
cycles) by adding eight extra clock cycles to the con-
version.
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________ 13
+5V
510k
100k
24k0.22µF
REFADJ
MAX1132
Figure 7. MAX1132 Reference-Adjust Circuit
MAX1132/MAX1133
Most applications require an input buffer amplifier. If
the input signal is multiplexed, the input channel should
be switched immediately after acquistion, rather than
near the end of or after a conversion. This allows more
time for the input buffer amplifier to respond to a large
step-change in input signal. The input amplifier must
have a high enough slew-rate to complete the required
output voltage change before the beginning of the
acquisition time. At the beginning of acquisition, the
capacitive DAC is connected to the amplifier output,
causing some output disturbance. Ensure that the sam-
pled voltage has settled to within the required limits
before the end of the acquisition time. If the frequency
of interest is low, AIN can be bypassed with a large
enough capacitor to charge the capacitive DAC with
very little change in voltage. However, for AC use, AIN
must be driven by a wideband buffer (at least 10MHz),
which must be stable with the DACs capacitive load (in
parallel with any AIN bypass capacitor used) and also
settle quickly (Figures 8 or 9).
Digital Noise
Digital noise can couple to AIN and REF. The conver-
sion clock (SCLK) and other digital signals that are
active during input acquisition contribute noise to the
conversion result. If the noise signal is synchronous to
the sampling interval, an effective input offset is pro-
duced. Asynchronous signals produce random noise
on the input, whose high-frequency components may
be aliased into the frequency band of interest. Minimize
noise by presenting a low impedance (at the frequen-
cies contained in the noise signal) at the inputs. This
requires bypassing AIN to AGND, or buffering the input
with an amplifier that has a small-signal bandwidth of
several MHz, or preferably both. AIN has a bandwidth
of about 4MHz.
Offsets resulting from synchronous noise (such as the
conversion clock) are canceled by the MAX1132/
MAX1133’s calibration scheme. The magnitude of the
offset produced by a synchronous signal depends on
the signal’s shape. Recalibration may be appropriate if
the shape or relative timing of the clock or other digital
signals change, as might occur if more than one clock
signal or frequency is used.
Distortion
Avoid degrading dynamic performance by choosing an
amplifier with distortion much less than the MAX1132/
MAX1133’s THD (-90dB) at frequencies of interest. If
the chosen amplifier has insufficient common-mode
rejection, which results in degraded THD performance,
use the inverting configuration to eliminate errors from
common-mode voltage. Low temperature-coefficient
resistors reduce linearity errors caused by resistance
changes due to self-heating. To reduce linearity errors
due to finite amplifier gain, use an amplifier circuit with
sufficient loop gain at the frequencies of interest.
DC Accuracy
If DC accuracy is important, choose a buffer with an
offset much less than the MAX1132/MAX1133’s maxi-
mum offset (±6mV), or whose offset can be trimmed
while maintaining good stability over the required tem-
perature range.
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
14 ______________________________________________________________________________________
Table 3. Unipolar Full Scale and Zero Scale
PART REFERENCE ZERO SCALE FULL SCALE
Internal 0 +12V
MAX1132 External 0 +12(VREF/4.096)
Internal 0 +4.096V
MAX1133 External 0 +VREF
Table 4. Bipolar Full Scale, Zero Scale, and Negative Scale
PART REFERENCE NEGATIVE FULL
SCALE ZERO SCALE FULL SCALE
Internal -12V 0 +12V
MAX1132 External -12(VREF/4.096) 0 +12(VREF/4.096)
Internal -4.096V 0 +4.096V
MAX1133 External -VREF 0+V
REF
Operating Modes and Serial Interfaces
The MAX1132/MAX1133 are fully compatible with
MICROWIRE and SPI/QSPI devices. MICROWIRE and
SPI/QSPI both transmit a byte and receive a byte at the
same time. The simplest software interface requires
only three 8-bit transfers to perform a conversion (one
8-bit transfer to configure the ADC, and two more 8-bit
transfers to clock out the 16-bit conversion result).
Short Acquisition Mode (24 SCLK)
Configure short acquisition by setting M1 = 0 and M0 =
0. In short acquisition mode, the acquisition time is 5.5
clock cycles. The total period is 24 clock cycles per
conversion.
Mode 2 Long Acquisition Mode (32 SCLK)
Configure long acquisition by setting M1 = 1 and M0 =
1. In long acquisition mode, the acquisition time is 13.5
clock cycles. The total period is 32 clock cycles per
conversion.
Calibration Mode
A calibration is initiated through the serial interface by
setting M1 = 0, M0 = 1. Calibration can be done in
either internal or external clock mode, though it is desir-
able that the part be calibrated in the same mode in
which it will be used to do conversions. The part will
remain in calibration mode for approximately 80,000
clock cycles unless the calibration is aborted.
Calibration is halted if RST or SHDN goes low, or if a
valid start condition occurs.
Software Shutdown
A software power-down is initiated by setting M1 = 1,
M0 = 0. After the conversion completes, the part shuts
down. It reawakens upon receiving a new start bit.
Conversions initiated with M1 = 1 and M0 = 0 (shut-
down) use the acquisition mode selected for the previ-
ous conversion.
Shutdown Mode
The MAX1132/MAX1133 may be shut down by pulling
SHDN low or by asserting software shutdown. In addi-
tion to lowering power dissipation to 13µW, consider-
able power can be saved by shutting down the
converter for short periods (duration will be affected by
REF startup time with internal reference) between con-
versions. There is no need to perform a calibration after
the converter has been shut down, unless the time in
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________ 15
4
7
6
2
3
IN
+15V
-15V
0.0033µF
0.1µF
0.1µF
100pF
1k
20
AIN
MAX427
ELANTEC
EL2003
Figure 8. AIN Buffer for AC/DC Use
4
7
6
2
3
IN
+5V
-5V
AIN
0.1µF
0.1µF
0.1µF
22
510
MAX410
Figure 9. ±5V Buffer for AC/DC Use Has ±3.5V Swing
MAX1132/MAX1133
shutdown is long enough that the supply voltage or
ambient temperature may have changed.
Supplies, Layout, Grounding
and Bypassing
For best system performance, use separate analog and
digital ground planes. The two ground planes should
be tied together at the MAX1132/MAX1133. Use pins 3
and 14 as the primary AGND and DGND, respectively.
If the analog and digital supplies come from the same
source, isolate the digital supply from the analog with a
low value resistor (10).
The MAX1132/MAX1133 are not sensitive to the order
of AVDD and DVDD sequencing. Either supply can be
present in the absence of the other. Do not apply an
external reference voltage until after both AVDD and
DVDD are present.
Be sure that digital return currents do not pass through
the analog ground. All return current paths must be
low-impedance. A 5mA current flowing through a PC
board ground trace impedance of only 0.05creates
an error voltage of about 250µV, or about 2LSBs error
with a ±4V full-scale system. The board layout should
ensure as much as possible that digital and analog sig-
nal lines are kept separate. Do not run analog and digi-
tal lines parallel to one another. If you must cross one
with the other, do so at right angles.
The ADC is sensitive to high-frequency noise on the
AVDD power supply. Bypass this supply to the analog
ground plane with 0.1µF. If the main supply is not ade-
quately bypassed, add an additional 1µF or 10µF low-
ESR capacitor in parallel with the primary bypass
capacitor.
Transfer Function
Figures 10 and 11 show the MAX1132/MAX1133’s
transfer functions. In unipolar mode, the output data is
binary format and in bipolar mode it is two’s comple-
ment.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. INL for
the MAX1132/MAX1133 is measured using the end-
point method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step-width and the ideal value of 1LSB. A
DNL error specification of less than 1LSB guarantees
no missing codes and a monotonic transfer function.
Aperture Jitter
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between the samples.
Aperture Delay
Aperture delay (tAD) is the time between the falling
edge of the sampling clock and the instant when an
actual sample is taken.
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital sam-
ples, signal-to-noise ratio (SNR) is the ratio of full-scale
analog input (RMS value) to the RMS quantization error
(residual error). The ideal, theoretical, minimum analog-
to-digital noise is caused by quantization error only and
results directly from the ADCs resolution (N bits):
SNR = (6.02 N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise, including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is calculated by taking
the ratio of the RMS signal to the RMS noise, which
includes all spectral components minus the fundamen-
tal, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion
Signal-to-Noise Plus Distortion (SINAD) is the ratio of
the fundamental input frequency’s RMS amplitude to
the RMS equivalent of all other ADC output signals:
SINAD (dB) = 20 log (SignalRMS/NoiseRMS)
Effective Number of Bits
Effective number of bits (ENOB) indicates the global
accuracy of an ADC at a specific input frequency and
sampling rate. An ideal ADCs error consists of quanti-
zation noise only. With an input range equal to the full-
scale range of the ADC, calculate the effective number
of bits as follows:
ENOB = (SINAD - 1.76) / 6.02
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of the first five harmonics of the input signal to the
fundamental itself. This is expressed as:
THD=× +++
20 223242521
log /VVVV V
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
16 ______________________________________________________________________________________
where V1is the fundamental amplitude, and V2through
V5are the amplitudes of the 2nd- through 5th-order
harmonics.
Spurious-Free Dynamic Range
Spurious-free dynamic range (SFDR) is the ratio of RMS
amplitude of the fundamental (maximum signal compo-
nent), to the RMS value of the next largest distortion
component.
Chip Information
TRANSISTOR COUNT: 21,807
PROCESS: BiCMOS
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
______________________________________________________________________________________ 17
OUTPUT CODE
FULL-SCALE
TRANSITION
11 . . . 111
11 . . . 110
11 . . . 101
00 . . . 011
00 . . . 010
00 . . . 001
00 . . . 000
12 3
0FS
FS - 3/2LSB
FS = +2.048V
1LSB =
INPUT VOLTAGE (LSBs)
65536
FS
Figure 10. MAX1135 Unipolar Transfer Function, 2.048V = Full
Scale
011 . . . 111
011 . . . 110
000 . . . 010
000 . . . 001
000 . . . 000
111 . . . 111
111 . . . 110
111 . . . 101
100 . . . 001
100 . . . 000
-FS 0V
INPUT VOLTAGE (LSBs)
+FS - 1LSB
+FS = +4.096V
-FS = -4.096V
1LSB = 65536
OUTPUT CODE
8.192
Figure 11. MAX1133 Bipolar Transfer Function, 4.096V = Full
Scale
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
18 ______________________________________________________________________________________
Ordering Information (continued)
PART TEMP. RANGE PIN-PACKAGE INL
(LSB
)
MAX1132AEAP* -40°C to +85°C 20 SSOP ±1.5
MAX1132BEAP -40°C to +85°C 20 SSOP ±2.5
MAX1133ACAP* 0°C to +70°C 20 SSOP ±1.5
MAX1133BCAP 0°C to +70°C 20 SSOP ±2.5
MAX1133AEAP* -40°C to +85°C 20 SSOP ±1.5
MAX1133BEAP -40°C to +85°C 20 SSOP ±2.5
Functional Diagram
CREF
AVDD
9k
AGND
REFADJ
REF
CS
RST
REFERENCE
AIN
DVDD
DGND
SCLK
DIN
ANALOG TIMING CONTROL
INPUT
SCALING
NETWORK
SERIAL
OUTPUT
PORT
SERIAL
INPUT
PORT
MEMORY CALIBRATION
ENGINE
CLOCK
GENERATOR CONTROL
DAC COMPARATOR
P2
SSTRB
DOUT
P1
P0
SHDN
MAX1132
MAX1133
Typical Application Circuit
*Future product
MAX1132/MAX1133
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19
© 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
Package Information
SSOP.EPS
PACKAGE OUTLINE, SSOP, 5.3 MM
1
1
21-0056 C
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
NOTES:
1. D&E DO NOT INCLUDE MOLD FLASH.
2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED .15 MM (.006").
3. CONTROLLING DIMENSION: MILLIMETERS.
4. MEETS JEDEC MO150.
5. LEADS TO BE COPLANAR WITHIN 0.10 MM.
7.90
H
L
0
0.301
0.025
8
0.311
0.037
0
7.65
0.63
8
0.95
MAX
5.38
MILLIMETERS
B
C
D
E
e
A1
DIM
A
SEE VARIATIONS
0.0256 BSC
0.010
0.004
0.205
0.002
0.015
0.008
0.212
0.008
INCHES
MIN MAX
0.078
0.65 BSC
0.25
0.09
5.20
0.05
0.38
0.20
0.21
MIN
1.73 1.99
MILLIMETERS
6.07
6.07
10.07
8.07
7.07
INCHES
D
D
D
D
D
0.239
0.239
0.397
0.317
0.278
MIN
0.249
0.249
0.407
0.328
0.289
MAX MIN
6.33
6.33
10.33
8.33
7.33
14L
16L
28L
24L
20L
MAX N
A
D
eA1 L
C
HE
N
12
B
0.068