Series 2290 High Voltage Power Supplies * Source voltages up to 5kV and 10kV * Safety interlock controls high voltage output * IEEE-488 programmable * Protection module prevents damage to low voltage instrumentation TYPICAL APPLICATIONS * High voltage device breakdown testing * High voltage component testing * Insulation testing * High voltage resistivity measurements * High energy physics research Ordering Information 2290-5 5kV Power Supply, 120VAC Nominal Input Voltage 2290E-5 5kV Power Supply, 240VAC Nominal Input Voltage 2290J-5 5kV Power Supply, 100VAC Nominal Input Voltage 2290-10 10kV Power Supply 2290-PM-200 10kV Protection Module Accessories Supplied CD with user manual, software drivers, and accessory information Power cord Series 2290 High Voltage Power Supplies facilitate high voltage device and material testing, as well as high energy physics experimentation. The Model 2290-5 5kV Power Supply provides voltage outputs up to 5000V, and the Model 2290-10 10kV Power Supply offers up to 10,000V. The Model 2290-5 has a 5mA current capacity, and the Model 2290-10 has a 1mA current capacity. These supplies measure both output voltage with 1V resolution and output current with 1A resolution. In addition to the voltage and current output displays, a third display shows one of four settings: output voltage, voltage limit, current limit, or current trip. These values can be set precisely with the front panel keypad. The settings can also be programmed over the IEEE-4888 interface, or the output voltage can be set with an analog control voltage. High voltage power supplies * Low noise for precision sourcing and sensitive measurements; selectable filters reduce noise to less than 3mV RMS on the 5kV supply Low Noise Ensures Accurate Low Level Measurements Low output noise is essential when using sensitive measurement instruments to make leakage current or high resistivity measurements. The maximum output ripple for the Model 2290-10 is less than 1V RMS. The maximum output ripple of the Model 2290-5 is 100mV RMS. Two selectable, internal filters on the Model 2290-5 reduce the maximum output ripple to only 3mV RMS. Extremely low noise from both power supplies enables sensitive measurement instruments to make accurate current measurements down to picoamp levels. Protecting User and Instrumentation Series 2290 Power Supplies and a Model 2290PM-200 Protection Module protect both user and instrumentation from hazardous voltages. An interlock circuit built into the power supplies can be used to ensure that the output voltage is disabled if a high voltage test fixture access door is open. In addition, all Series 2290 power supplies have low voltage analog outputs to permit safe monitoring of the high voltage and the output current. When low voltage measurement instrumentation is used in the high voltage circuit, the protection module safely clamps the voltage across the instrument to a maximum value of 200V even when a device under test (DUT) breaks down. Thus, a Series 2290 Power Supply, Model 2290PM-200 Protection Module, and Keithley accessories provide all the elements for building a safe, high voltage test environment. The Model 2290-PM-200 Protection Module protects low voltage measurement equipment from voltages greater than 200V. 1.888.KEITHLEY (U.S. only) www.keithley.com A Greater Measure of Confidence DC POWER SUPPLIES Multi-channel programmable DC power supplies * 1A current measurement resolution Accessories Available For 2290-5: 2290-5-SHV 2290-5-MHV 2290-5-SHVBH 2290-5-RMK-1 High voltage power supplies 2290-5-RMK-2 5kV SHV Female-SHV Female Cable, 3m (10 ft) 5kV SHV Female-MHV Male Cable, 3m (10 ft) 5kV SHV Male Bulkhead Connector Single Fixed Rack Mount Kit for 5kV Power Supply Dual Fixed Rack Mount Kit for 5kV Power Supply For 2290-10: 2290-10-SHVUC 10kV SHV Male to Unterminated Cable, 3m (10ft) 2290-10-SHV 10kV SHV Male-SHV Male Cable, 3m (10 ft) 2290-10-SHVBH 10kV SHV Female Bulkhead Connector 2290-10-RMK-1 Single Fixed Rack Mount Kit for 10kV Power Supply 2290-10-RMK-2 Dual Fixed Rack Mount Kit for 10kV Power Supply For both: 2290-PM-200 10kV Protection Module 2290-INT-CABLE 3-Pin Connector to Unterminated Interlock Cable 4299-7 Fixed Shelf Rack Mount Kit KPCI-488LPA IEEE-488.2 Interface Board for the PCI Bus KUSB-488B IEEE-488.2 USB-GPIB Interface Adapter for USB port with built-in 2m (6.6 ft) cable 7007-05 Double Shielded Premium IEEE-488 Interface Cable, 0.5m (1.6 ft) 7007-1 Double Shielded Premium IEEE-488 Interface Cable, 1m (3.2 ft) 7007-2 Double Shielded Premium IEEE-488 Interface Cable, 2m (6.5 ft) 7007-3 Double Shielded Premium IEEE-488 Interface Cable, 3m (10 ft) 7007-4 Double Shielded Premium IEEE-488 Interface Cable, 4m (13 ft) Services Available High Voltage Power Supplies Make Precise Current Measurements Lower Than 1A Use a sensitive Keithley measurement instrument, such as a Keithley SourceMeter(R) Source Measure Unit (SMU) instrument, to measure current drawn by the device under test (DUT) that is below the sensitivity of the Series 2290 Power Supplies. Keithley SourceMeter SMU instruments can provide sensitivity as low as 0.1fA. The following diagram shows how the Model 2290-PM-200 Protection Module protects the low voltage SourceMeter SMU instrument from high voltages when the DUT breaks down. The leakage current of the protection module limits the measurement resolution to picoamp levels, which is five decades more sensitive than the current measurement resolution of the Series 2290 Power Supplies. Keithley can provide a complete high voltage test capability with the most current measurement sensitivity available anywhere. Model 2290-5 High Voltage Power Supply Model 2290-PM-200 Protection Module PM Reverse breakdown testing of a high voltage diode using a Keithley SourceMeter SMU instrument to measure leakage current. The Model 2290-PM-200 SMU Protection Module protects the SourceMeter SMU instrument from high voltage when the diode breaks down. Easily Automate a High Voltage Test System The Series 2290's IEEE-488 interface allows the creation of an automated high voltage test system. Software drivers are supplied to simplify and accelerate test system development. This further enhances safety as the high voltage can be controlled from a remote location. 1 Year Factory Warranty extended one additional year from date of shipment Model Number-3Y-EW 1 Year Factory Warranty extended to 3 years frcom date of shipment Model Number-5Y-EW 1 Year Factory Warranty extended to 5 years from date of shipment C/Model Number-3Y-STD KeithleyCare 3 Year Standard Calibration Plan C/Model Number-3Y-DATA KeithleyCare 3 Year Calibration with Data Plan C/Model Number-5Y-STD KeithleyCare 5 Year Standard Calibration Plan C/Model Number-5Y-DATA KeithleyCare 5 Year Calibration with Data Plan Model Number*-EW DC POWER SUPPLIES A Model 263xB System SourceMeter SMU Instrument configured as an ammeter *Insert model number. Examples: 2290-5-EW, C/2290E-10-3Y-STD 1.888.KEITHLEY (U.S. only) www.keithley.com A Greater Measure of Confidence High voltage power supplies Series 2290 Series 2290 High Voltage Power Supplies 2290-5 Specifications 5kV Voltage Power Supply Characteristics Output Voltage1 50 to +5000 V DC 50 to +3000 V DC 50 to +5000 V DC GENERAL Maximum Output Current 5.000 mA DC 5.000 mA DC 3.000 mA DC Conditions No filter Filter 1 Filter 2 Voltage set accuracy2: (0.01% of setting + 2.5V). Voltage display accuracy: Voltage set accuracy 1V, typical (2V, maximum). Voltage resolution: 1V (set and display). Voltage limit range: 0 to 100% full scale. Line: 0.001% for 10% line voltage change. Voltage regulation3: Load: 0.005% for 100% load change, typical. Output ripple (10kHz-100kHz)4: 0.002% of full scale, V RMS, maximum - No filter. 1.0mV RMS @ 1kV - Filter 1 or Filter 2. 2.0mV RMS @ 3kV - Filter 1 or Filter 2. 3.0mV RMS @ 5kV - Filter 2. 1.5 seconds for 0 to within 1V of 5000VDC - No filter. Rise time (full load) 6, 7: 3 seconds for 0 to within 1V of 3000VDC - Filter 1. 4 seconds for 0 to within 1V of 5000VDC - Filter 2 1 second for 5000VDC to 1VDC - No filter. Discharge time (full load) 6, 7: 3 seconds for 3000VDC to 1VDC - Filter 1. 4 seconds for 5000VDC to 1VDC - Filter 2 <12 seconds (to <50VDC) - No filter. Discharge time (no load) 6: <30 seconds (to <50VDC) - Filter 1 or Filter 2. Settling time 6, 7: From 0 to programmed voltage; to within 99.9% of final value within 3 seconds. Recovery time 6, 7: 120ms for 40% step change in load current (typical). Current Limit and Trip Range 0.4 mA to 5.25 mA 0.4 mA to 3.25 mA 0.5 mA to 5.25 mA 0.4 mA to 3.25 mA Voltage Range 0 V to 1.5 kV 1.5 kV to 5.0 kV Filter No filter or Filter 1 Filter 2 No filter or Filter 1 Filter 2 Input power: 55 watts. 2290-5 Input voltage: 120V 10%, 50 or 60Hz. 2290E-5 Input voltage: 240V 10%, 50 or 60Hz. 2290J-5 Input voltage: 100V 10%, 50 or 60Hz. Rear panel connectors: SHV male (Kings type 1704-1 or equivalent). Output high-voltage connector GPIB connector. BNC Connector (two): Voltage set/Voltage monitor; Current monitor. Toggle switch: Voltage setting or Voltage monitor. High-voltage safety interlock: Connector: 3-pin press-in connector, 3M part number: 37103-A165-00E-MB. Pin 1: 5V out, 1.5mA maximum out. Pin 2: Input: High-voltage output enabled: 3-24V DC. High-voltage output disabled: <1.2V DC. Pin 3: Chassis ground through a 100 resistor. Interface protocol: IEEE-488.1. Operating environment: 0 to 40C; non-condensing. Dimensions: 89mm high x 206mm wide x 406mm deep (3.5 in. x 8.1 in. x 16 in.). Weight: 5.5kg (12 pounds). Safety: Conformance to European Union low voltage directive. Warranty: One year. Warm-up time: One hour. 1. The output voltage can be programmed to a voltage lower than 50V; however, performance below 50V is not specified. 2. Add 2.5VDC when Filter 1 or Filter 2 is enabled. 3. Regulation specifications apply for greater than 25VDC (with full load), or 50VDC (with no load). Below these values, the unit may not regulate correctly. 4. Peak-to-peak values are within five times the RMS value. 5. Add 2.5A offset when Filter 1 or Filter 2 is enabled. 6. Times apply with the current limit set to 105% of full scale. 7. Loads are fully resistive. Current set accuracy5: 0.01% (0.01% + 2.5A). Current resolution: 1A. Current display accuracy: 1A, typical (2A, maximum). Stability: 0.01% per hour; <0.03% per eight hours. Temperature drift: 50ppm/C, 0 to 40C, typical. Protection: Arc and short circuit protected; programmable voltage and current limits and current trip. Monitor outputs Output scale: 0 to +10V to full scale. Current rating: 10mA maximum. Output impedance: <1. Accuracy: 0.2% of full scale with a 100k load, minimum. Update rate: 8Hz. Model 2290-5 rear panel showing the IEEE-488 interface connector, high voltage output connector, analog control/output connectors, and interlock connector. 1.888.KEITHLEY (U.S. only) www.keithley.com A Greater Measure of Confidence DC POWER SUPPLIES High voltage power supplies CHARACTERISTICS VOLTAGE RANGE: External voltage set Input scale: 0 to +10V for 0 to full scale. Input impedance: 1M. Accuracy: 0.2% of full scale. Update rate: 16Hz. Output slew rate: <(rise time + 0.3 seconds) for 0 to full range under full load. High voltage power supplies CONDITIONS This document contains specifications and supplemental information for the Model 2290-5 High Voltage Power Supply. Specifications are the standards against which the Model 2290-5 is tested. Upon leaving the factory, the Model 2290-5 meets these specifications. Characteristics, supplemental characteristics, and typical values are not warranted, apply at 23C 5C, <70% relative humidity, and are provided solely as useful information. Series 2290 High Voltage Power Supplies 2290-10 Specifications 10kV Voltage Power Supply Characteristics High voltage power supplies CHARACTERISTICS VOLTAGE RANGE: Output Voltage 1 +100 to +10,000 V DC Maximum Output Current 1.000 mA DC Voltage set accuracy: 0.06% of full scale. Voltage display accuracy: Voltage set accuracy 1V, typical (2V, maximum). Voltage resolution: 1V (set and display). Voltage limit range: 0 to 100% full scale. Voltage regulation 2: Line: 0.001% for 10% line voltage change. Load: 0.04% for 100% load change, typical. Output ripple (300Hz-300kHz): 0.01% of full scale, V RMS. Rise time (from high voltage turn on to final value under full load) 3, 4: <6 seconds to within 1V of the final value. Discharge time (to 0V under full load) 3, 4: 1 second to under 10V. Discharge time (no load) 3: <6 seconds (to <1% of full scale voltage with no load, typical). Settling time 3, 4: <4 seconds to within 1V of the final value. Recovery time 3, 4: 120ms for 40% step change in load current (typical). Monitor outputs Output scale: 0 to +10V for 0V to full scale. Current rating: 10mA maximum. Output impedance: 100. Accuracy: 0.2% of full scale with a 1M load, minimum. Update rate: 87.5Hz. External voltage set Input scale: 0 to +10V for 0 to full scale. Input impedance: 1M. Accuracy: 0.2% of full scale. Update rate: 87.5Hz. Output slew rate (5% to 95% under full load): <3 seconds GENERAL Input power: 75 watts. Input voltage: 90V-264VAC, 47 to 63Hz. Rear panel connectors: Output high-voltage connector: SHV male (Kings type 1764-1 or equivalent). BNC Connector (three): Input, voltage monitor; current monitor. GPIB connector, 23-pin. RS-232, 9-pin D-sub High-voltage safety interlock: Connector: 3-pin press-in connector, 3M part number: 37103-A165-00E-MB. Pin 1: 5V out, 70mA maximum out. Pin 2: Input: High-voltage output enabled:5V DC. High-voltage output disabled: 0V DC or open connection. Pin 3: Chassis ground. Interface protocol: IEEE-488.1. Operating environment: 0 to 40C; non-condensing. Dimensions: 89mm high x 206mm wide x 406mm deep (3.5 in x 8.1 in x 16 in). Weight: 3.7kg (8 pounds). Safety: Conformance to European Union low voltage directive. Warranty: One year. Warm-up time: One hour. Current limit range: 0 to 105% of full scale. Current set accuracy: 0.5% of full scale. Current resolution: 1A. Current display accuracy: 1A, typical (2A, maximum). Trip current range: 10A to 105% of full scale (excluding stored output charge). Output Stored Charge: <20C maximum. Trip response time: <10ms. DC POWER SUPPLIES Stability: 0.01% per hour; <0.03% per eight hours. Temperature drift: 50ppm/C, 0 to 40C, typical. Protection: Arc and short circuit protected; programmable voltage and current limits and current trip. 1. 2. 3. 4. The output voltage can be programmed to voltages below 100V, but accuracy below 100V is not specified. Regulation specifications apply for greater than 100V. Times apply with the current limit set to 105% of full scale. Loads are fully resistive. Model 2290-10 rear panel showing the IEEE-488 interface connector, RS-232 interface connector, high voltage output connector, analog control/output connectors, and interlock connector. 1.888.KEITHLEY (U.S. only) www.keithley.com A Greater Measure of Confidence High voltage power supplies CONDITIONS This document contains specifications and supplemental information for the Model 2290-10 High Voltage Power Supply. Specifications are the standards against which the Model 2290-10 is tested. Upon leaving the factory, the Model 2290-10 meets these specifications. Characteristics, supplemental characteristics, and typical values are not warranted, apply at 23C 5C, <70% relative humidity, and are provided solely as useful information. Series 2290 High Voltage Power Supplies 2290-PM-200 Specifications SMU Protection Module Characteristics High voltage power supplies CHARACTERISTICS Leakage: <10pA at 200V typical. DC current carrying capability: <1.5A in unclamped condition. Pulsed current carrying capability: 10A maximum at 1% duty cycle in unclamped condition. Maximum protection active current: Current must be limited to <120mA in clamped condition (~230V). Protection voltage: 220VDC minimum, 230VDC typical, 240VDC maximum. Dimensions: 81.28mm long x 81.53mm wide x 54.10mm high (3.20 in. long x 3.21 in. wide x 2.13 in. high) Maximum length with high-voltage connectors: 5.34 in (135.64mm). Weight: 0.25kg (0.55 lb.). GENERAL Warranty: 1 year. Safety: Listed to UL 61010-1:2012 (3rd edition). Conforms to European Union Low Voltage Directive. CONNECTORS: High Voltage: 5kV connector: male SHV, 0.38 inches (9.35mm) diameter, Kings 1704-1. 10kV connector: female SHV, 0.535 inches (13.59mm) diameter, Kings 1764-1. Low Voltage: Triax, female, quantity of 2 Safety: Screw ground terminal, quantity of 2 DC POWER SUPPLIES High voltage power supplies CONDITIONS This document contains specifications and supplemental information for the Model 2290-PM200 Protection Module. Specifications are the standards against which the Model 2290-PM-200 is tested. Upon leaving the factory, the Model 2290-PM-200 meets these specifications. Characteristics, supplemental characteristics, and typical values are not warranted, apply at 23C 5C, <70 percent relative humidity, and are provided solely as useful information. 1.888.KEITHLEY (U.S. only) www.keithley.com A Greater Measure of Confidence High voltage power supplies High Voltage Power Supplies High voltage power supplies Series 2290 Specifications are subject to change without notice. All Keithley trademarks and trade names are the property of Keithley Instruments, Inc. All other trademarks and trade names are the property of their respective companies. A Greater Measure of Confidence DC POWER SUPPLIES KEITHLEY INSTRUMENTS, INC. 28775 AURORA RD. CLEVELAND, OH 44139-1891 440-248-0400 Fax: 440-248-6168 1-888-KEITHLEY www.keithley.com BENELUX +31-40-267-5506 www.keithley.nl FRANCE +33-01-69-86-83-60 www.keithley.fr ITALY +39-049-762-3950 www.keithley.it MALAYSIA 60-4-643-9679 www.keithley.com SINGAPORE 01-800-8255-2835 www.keithley.com.sg BRAZIL 55-11-4058-0229 www.keithley.com GERMANY +49-89-84-93-07-40 www.keithley.de JAPAN 81-120-441-046 www.keithley.jp MEXICO 52-55-5424-7907 www.keithley.com TAIWAN 886-3-572-9077 www.keithley.com.tw CHINA 86-10-8447-5556 www.keithley.com.cn INDIA 080-30792600 www.keithley.in KOREA 82-2-6917-5000 www.keithley.co.kr RUSSIA +7-495-664-7564 www.keithley.ru UNITED KINGDOM +44-1344-39-2450 www.keithley.co.uk For further information on how to purchase or to locate a sales partner please visit www.keithley.com/company/buy (c) Copyright 2013 Keithley Instruments, Inc. Printed in the U.S.A No. 3241 01.22.14 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Keithley Instruments, Inc.: 2290E-5 2290J-5 2290-5 2290-10