ADA10001 Linear Amplifier MMIC Data Sheet - Rev 2.3 FEATURES * High Linearity: +18 dBm IIP3 * Low Noise Figure: 2.0 dB * Single Supply: +8 VDC * Wide Bandwidth: 50 MHz to 1 GHz * RoHS-Compliant Package Option APPLICATIONS * Driver Amplifier * CATV - Distribution / Drop Amplifiers S3 Package Modified 16 Pin SOIC PRODUCT DESCRIPTION The ADA10001 is a monolithic IC intended for use in applications requiring high linearity, such as Cellular Telephone Base Station Driver Amplifiers, CATV Fiber Receiver and Distribution Amplifiers and CATV Drop RF Input Amplifiers. Offered in a modified 16 lead surface mount SOIC package, it is well suited for use in amplifiers where small size, reduced component count, and high reliability are important. 15 dB Figure 1: Block Diagram 02/2005 RF Output / Bias ADA10001 1 GND GND 16 2 GND GND 15 3 GND RFOUT 14 4 GND GND 13 5 GND GND 12 6 RFIN GND 11 7 GND GND 10 8 GND GND 9 Figure 2: Pin Out Table 1: Pin Description 2 PIN NAME 1 GND 2 DESCRIPTION PIN NAME Ground 9 GND Ground GND Ground 10 GND Ground 3 GND Ground 11 GND Ground 4 GND Ground 12 GND Ground 5 GND Ground 13 GND Ground 6 RFIN RF Input 14 RFOUT RF Output / Supply 7 GND Ground 15 GND Ground 8 GND Ground 16 GND Ground Data Sheet - Rev 2.3 02/2005 DESCRIPTION ADA10001 ELECTRICAL CHARACTERISTICS Table 2: Absolute Maximum and Minimum Ratings PARAMETER MIN MAX UNIT Supply (pin 14) 0 +12 VD C RF Power at Input (pin 6) - +10 dB m -65 +150 o C Soldering Temperature - 260 o C Soldering Time - 5 Storage Temperature se c Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Note: 1. Pin 6 should be AC-coupled. No external DC bias should be applied. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT RF Input / Output Frequency 50 - 1000 MHz Supply Voltage: VDD (pin 14) +4 +8 +9 VD C Case Temperature -40 - +85 (1) o C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Note: (1) Median time to failure will degrade above this temperature. Data Sheet - Rev 2.3 02/2005 3 ADA10001 Table 4: Electrical Specifications ) (TA = +25 C, VDD = + 8 VDC, Test System = 75 PARAMETER MIN TYP MAX UNIT CSO (1) 60 - - dB c CTB 65 - - dB c 14 15 - dB - 2.0 3.5 dB 2nd Order Input Intercept Point (IIP2) (2) +35 +38 - dB m 3rd Order Input Intercept Point (IIP3) (2) +15 +18 - dB m - - 35 50 - 150 (1) Gain Noise Figure Thermal Resistance Current Consumption (3) o C/W mA Notes: (1) 160 channels, +23 dBmV per channel (measured at output), 6 MHz channel spacing (2) Two tones, -10 dBm per tone at input (3) The device can be operated at VDD = +6 VDC for lower power dissipation. Refer to the figures on page 5 for performance variation with supply voltage. 1000 pF 5W RF IN 2.7 pF Figure 3: Test Circuit 4 VDD 0.1mf 5.6 nH Data Sheet - Rev 2.3 02/2005 OUT 1.5 pF 3.9 mH 1000 pF RF ADA10001 PERFORMANCE DATA Figure 4: Gain Noise Figure vs. Frequency TA = 25 oC, VDD = +8V Gain (dB) 3.5 16 3 15 2.5 14 2 13 1.5 12 1 50 250 450 650 Frequency (MHz) 850 Figure 5: Gain and Noise Figure vs. VDD T A = 25 o C, RF = 500 MH z 15.8 GAIN 15.75 Gain (dB) NF Noise Figure (dB) GAIN 17 4 2.02 NF 2 1.98 15.7 1.96 15.65 1.94 1.92 15.6 1.9 15.55 Noise Figure (dB) 18 1.88 4 5 6 7 V DD (Volts) 8 9 Figure 6: IIP2, IIP3 vs. VDD TA = 25 oC IIP2 IIP2 (dBm ) 36 24 IIP3 20 32 28 16 IIP3 (dBm ) 40 24 20 12 4 5 6 7 VDD (Volts) 8 9 Notes: 1. IIP2 measured at 986.5 MHz; Input = two tones at 55.25 MHz and 931.25 MHz at -10 dBm. 2. IIP3 measured with two tones at the input: 986.5 MHz and 992.5 MHz at -10 dBm. Data Sheet - Rev 2.3 02/2005 5 ADA10001 Figure 7: Output Power vs. Input Power TA = 25 oC, VDD = +8V, RF = 500 MHz 26 Output Power (dBm) 25 24 23 22 21 20 19 18 17 16 15 0 2 4 6 8 Input Power (dBm) 10 12 Figure 8: Input Impedance START: 0.050 GHz STOP: 1.00 GHz 1: 0.050 GHz 79.76 W 2: 0.20 GHz 77.88 W - 13.21 jW 3: 0.40 GHz 70.02 W - 21.83 jW 4: 0.6 GHz 59.63 W - 26.56 jW 5: 0.8 GHz 49.91 W - 26.56 jW 6: 1.0 GHz 41.77 W - 25.15 jW - 4.79 j W 1 .5 2 5 .2 5 0 .2 .5 -.2 1 1 2 3 2 5 4 6 5 -5 -2 -.5 -1 Measured in 75 W System Figure 9: Output Impedance START: 0.050 GHz STOP: 1.00 GHz 1 .5 2: 0.20 GHz 84.17 W - 1.19 jW 3: 0.40 GHz 85.38 W - 2.27 jW 4: 0.6 GHz 87.64 W - 3.82 jW 5: 0.8 GHz 90.20 W - 6.60 jW 6: 1.0 GHz 93.57 W - 11.76 jW 5 5 1 .2 .5 1 6 2 5 -.2 -5 -2 -.5 -1 Measured in 75 W System 6 0.050 GHz 83.9 W - 8.1 jW 2 .2 0 1: Data Sheet - Rev 2.3 02/2005 ADA10001 PACKAGE OUTLINE D C LE E H L 0.015 [0.38]X45 a A2 A A1 GAUGE PLANE 0.003 [0.076mm] B1 e S Y M INCHES B O L MILLIMETERS MIN. MAX. MIN. MAX. A 0.058 0.068 1.47 1.73 A1 0.004 0.010 0.10 0.25 A2 0.055 0.065 1.40 1.65 B 0.013 0.020 0.33 0.50 B1 0.062 0.070 1.58 1.78 NOTE NOTES: 2. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.006 [0.15mm] PER SIDE. 3. DIMENSION "E" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.010 [0.25mm] PER SIDE. C 0.008 0.010 0.20 0.25 4 0.380 0.400 9.66 10.16 2 E 0.150 0.160 3.81 4.06 3 0.050 BSC B 1. CONTROLLING DIMENSION: INCHES D e 4. LEAD THICKNESS AFTER PLATING TO BE 0.013 [0.33mm] MAXIMUM. 1.27 BSC H 0.226 0.244 5.74 6.20 SPECIFICATION: 0.040 0.41 1.02 SUBJECT: L 0.016 LE 0.030 a 0 0 98000-006 PUBLISHED OUTLINE, 16 LEAD BATWING SOIC PKG. 0.76 8 SEATING PLANE 8 Figure 10: S3 Package Outline - Modified 16 Pin SOIC Data Sheet - Rev 2.3 02/2005 7 ADA10001 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION ADA10001S3CTR -40 oC to +85 oC Modified 16 Pin SOIC 3,500 piece Tape and Reel A D A 10001S 3C -40 oC to +85 oC Modified 16 Pin SOIC Plastic tubes (50 pieces per tube) ADA10001RS3P1 -40 oC to +85 oC RoHS Compliant Modified 16 Pin SOIC 3,500 piece Tape and Reel COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.3 02/2005