02/2005
S3 Package
Modified 16 Pin SOIC
FEATURES
• High Linearity: +18 dBm IIP3
• Low Noise Figure: 2.0 dB
• Single Supply: +8 VDC
• Wide Bandwidth: 50 MHz to 1 GHz
• RoHS-Compliant Package Option
APPLICATIONS
• Driver Amplifier
• CATV - Distribution / Drop Amplifiers
PRODUCT DESCRIPTION
The ADA10001 is a monolithic IC intended for use in
applications requiring high linearity, such as Cellular
Telephone Base Station Driver Amplifiers, CATV Fiber
Receiver and Distribution Amplifiers and CATV Drop
Figure 1: Block Diagram
Amplifiers. Offered in a modified 16 lead surface
mount SOIC package, it is well suited for use in
amplifiers where small size, reduced component
count, and high reliability are important.
ADA10001
Linear Amplifier MMIC
Data Sheet - Rev 2.3
RF Output
/ Bias
RF Input
15 dB
ADA10001
Data Sheet - Rev 2.3
02/2005
2
NIP EMAN NOITPIRCSED NIP EMAN NOITPIRCSED
1DNGdnuorG9DNGdnuorG
2DNGdnuorG01DNGdnuorG
3DNGdnuorG11DNGdnuorG
4DNGdnuorG21DNGdnuorG
5DNGdnuorG31DNGdnuorG
6FR
NI
tupnIFR41FR
TUO
ylppuS/tuptuOFR
7DNGdnuorG51DNGdnuorG
8DNGdnuorG61DNGdnuorG
Table 1: Pin Description
1
2
GND
RF
OUT
GND
GND
GND
GND
8
7
6
5
4
3
16
15
9
10
11
12
13
14
RF
IN
GND
GND
GND
GND
GND
GND
GND
GND
GND
Figure 2: Pin Out
ADA10001
Data Sheet - Rev 2.3
02/2005
3
Table 2: Absolute Maximum and Minimum Ratings
ELECTRICAL CHARACTERISTICS
RETEMARAP NIM XAM TINU
)41nip(ylppuS021+CDV
)6nip(tupnItarewoPFR-01+mBd
erutarepmeTegarotS56-051+
o
C
erutarepmeTgniredloS-062
o
C
emiTgniredloS-5ces
Stresses in excess of the absolute ratings may cause permanent
damage. Functional operation is not implied under these conditions.
Exposure to absolute ratings for extended periods of time may
adversely affect reliability.
Note:
1. Pin 6 should be AC-coupled. No external DC bias should be applied.
Table 3: Operating Ranges
Note:
(1) Median time to failure will degrade above this temperature.
The device may be operated safely over these conditions; however, parametric
performance is guaranteed only over the conditions defined in the electrical
specifications.
RETEMARAP NIM PYT XAM TINU
ycneuqerFtuptuO/tupnIFR05- 0001zHM
V:egatloVylppuS
DD
)41nip(4+8+9+CDV
erutarepmeTesaC04--58+
)1(o
C
ADA10001
Data Sheet - Rev 2.3
02/2005
4
Table 4: Electrical Specifications
(TA = +25 °C, VDD = + 8 VDC, Test System = 75ΩΩ
ΩΩ
Ω )
Notes:
(1) 160 channels, +23 dBmV per channel (measured at output), 6 MHz channel spacing
(2) Two tones, -10 dBm per tone at input
(3) The device can be operated at VDD = +6 VDC for lower power dissipation. Refer to
the figures on page 5 for performance variation with supply voltage.
RETEMARAP NIM PYT XAM TINU
OSC
)1(
06-- cBd
BTC
)1(
56-- cBd
niaG4151- Bd
erugiFesioN-0.25.3Bd
tnioPtpecretnItupnIredrOdn2
)2PII(
)2(
53+83+- mBd
tnioPtpecretnItupnIredrOdr3
)3PII(
)2(
51+81+- mBd
ecnatsiseRlamrehT--53
o
W/C
noitpmusnoCtnerruC
)3(
05- 051Am
Figure 3: Test Circuit
1000 pF RF OUT
3.9 mH
VDD
0.1mf
RF IN 2.7 pF
5.6 nH
1000 pF
1.5 pF
5W
ADA10001
Data Sheet - Rev 2.3
02/2005
5
15.55
15.6
15.65
15.7
15.75
15.8
Gain (dB)
1.88
1.9
1.92
1.94
1.96
1.98
2
2.02
Noise Figure (dB)
456789
VDD (Volts)
GAIN NF
TA = 25 oC, RF = 500 MHz
Notes:
1. IIP2 measured at 986.5 MHz; Input = two tones at 55.25 MHz and 931.25 MHz at -10 dBm.
2. IIP3 measured with two tones at the input: 986.5 MHz and 992.5 MHz at -10 dBm.
12
13
14
15
16
17
18
Gain (dB)
1
1.5
2
2.5
3
3.5
4
Noise Figure (dB)
50 250 450 650 850
Frequency (MHz)
TA = 25 oC, VDD = +8V
GAIN NF
Figure 4: Gain Noise Figure vs. Frequency
Figure 5: Gain and Noise Figure vs. VDD
Figure 6: IIP2, IIP3 vs. VDD
PERFORMANCE DATA
20
24
28
32
36
40
IIP2 (dBm)
12
16
20
24
IIP3 (dBm)
456789
V
DD
(Volts)
T
A
= 25
o
C
IIP2 IIP3
ADA10001
Data Sheet - Rev 2.3
02/2005
6
5
2
1
.5
.2
0 .2 .5 1 2 5
5
-.2
-.5
-1
-2
-5
1: 0.050 GH
z
79.76 W
- 4.79 jW
2: 0.20 GHz
77.88 W
- 13.21 jW
3: 0.40 GHz
70.02
W
- 21.83 jW
4: 0.6 GHz
59.63
W
- 26.56 jW
5 : 0.8 GHz
49.91
W
- 26.56 jW
6: 1.0 GHz
41.77
W
- 25.15 jW
START: 0.050 GHz
STOP: 1.00 GHz
1
Measured in 75 W System
2
6
3
4
5
5
2
1
.5
.2
0 .2 .5 1 2 5
5
-.2
-.5
-1
-2
-5
1: 0.050 GH
z
83.9 W
- 8.1 jW
2: 0.20 GHz
84.17 W
- 1.19 jW
3: 0.40 GHz
85.38
W
- 2.27 jW
4: 0.6 GHz
87.64
W
- 3.82 jW
5 : 0.8 GHz
90.20
W
- 6.60 jW
6: 1.0 GHz
93.57
W
- 11.76 jW
START: 0.050 GHz
STOP: 1.00 GHz
1
6
Measured in 75 W System
Figure 8: Input Impedance
Figure 9: Output Impedance
15
16
17
18
19
20
21
22
23
24
25
26
Output Power (dBm)
0 2 4 6 8 10 12
Input Power (dBm)
TA = 25 oC, VDD = +8V, RF = 500 MHz
Figure 7: Output Power vs. Input Power
ADA10001
Data Sheet - Rev 2.3
02/2005
7
HE
eB 1
A
B
A
2
L
a
C
LE
0.003 [0.076mm]
A
1
GAUGE PLANE
SEATING PLANE
D
0.015 [0.38]X45
a
L
e
E
A
D
B
L
S
O
Y
B
MMILLIMETERSINCHES NOTE
MAX.MIN.MAX.MIN.
H
LE
C
2
3
4
1
B
0.020 0.500.330.013
0.10
1.47
0.25
1.730.068
0.010
0.058
0.004
0.055 0.065 1.651.40
0.250.200.0100.008
8080
6.205.740.2440.226
0.380
0.150
0.400
0.160 4.06
10.16
3.81
9.66
0.050 BSC 1.27 BSC
0.016 0.040 0.41 1.02
0.030 0.76
0.062 1.58 1.780.070
4. LEAD THICKNESS AFTER PLATING TO BE 0.013 [0.33mm]
MAXIMUM.
PER SIDE.
1. CONTROLLING DIMENSION: INCHES
2. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS
AND GATE BURRS SHALL NOT EXCEED 0.006 [0.15mm]
3. DIMENSION "E" DOES NOT INCLUDE INTER-LEAD FLASH OR
PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS
SHALL NOT EXCEED 0.010 [0.25mm] PER SIDE.
NOTES:
A2
A1
SPECIFICATION:
SUBJECT:
16 LEAD BATWING SOIC PKG.
PUBLISHED OUTLINE,
98000-006
PACKAGE OUTLINE
Figure 10: S3 Package Outline - Modified 16 Pin SOIC
ADA10001
Data Sheet - Rev 2.3
02/2005
8
ORDERING INFORMATION
REBMUNREDRO ERUTAREPMET
EGNAR
EGAKCAP
NOITPIRCSED GNIGAKCAPTNENOPMOC
RTC3S10001ADA04-
o
58+otC
o
CCIOSniP61deifidoMleeRdnaepaTeceip005,3
C3S10001ADA04-
o
58+otC
o
CCIOSniP61deifidoM)ebutrepseceip05(sebutcitsalP
1P3SR10001ADA04-
o
58+otC
o
CtnailpmoCSHoR
CIOSniP61deifidoM leeRdnaepaTeceip005,3
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS
product in any such application without written consent is prohibited.
IMPORTANT NOTICE
ANADIGICS, Inc.
141 Mount Bethel Road
Warren, New Jersey 07059, U.S.A.
Tel: +1 (908) 668-5000
Fax: +1 (908) 668-5132
URL: http://www.anadigics.com
E-mail: Mktg@anadigics.com
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without
notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are
subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are
assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges
customers to verify that the information they are using is current before placing orders.
