ACDC 500600 Watts SMC/SMD Series xppower.com * High Peak Load Rating * Single Outputs from 3.3 V to 54 V * Active PFC * Remote On/Off * Optional Current Share * SEMI F47 Compliant * 3 Year Warranty Specification Input General 90-264 VAC (120-370 VDC) 47-63 Hz 9 A at 90 VAC, 3.5 A at 230 VAC 40 A at 230 VAC EN61000-3-2 class A EN61000-3-2 class C for load 40% Earth Leakage Current * <2.4 mA max at 264 VAC Input Protection * Fitted with a T10 A/250 V fuse Input Voltage Input Frequency Input Current Inrush Current Power Factor * * * * * Efficiency Isolation Switching Frequency Power Density Signals Current Monitor Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load * * * * Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Over/Undershoot Transient Response * * * * * * * Ripple & Noise Overvoltage Protection Overtemperature Protection Overload Protection Short Circuit Protection Remote Sense * * * Remote On/Off * Current Share * * * * See tables 5% minimum 1% 1% load required to meet specified ripple & noise and regulation 1.5 s at 230 VAC, 2.5 s at 110 VAC 40 ms typical 18 ms min at 120 VAC 0.5%, low line to high line 1%, 1-100% of load, see note 4 5% max 5% max deviation, 500 s recovery to within 1% for a 50% load change See table 110-130% recycle input to reset >85 C ambient with auto recovery (measured internally) 110% to 135% with auto recovery Trip and restart (Hiccup mode) Compensates for up to 0.5 V line drop (not available with current share) On = TTL Logic HIGH, or open circuit Off = TTL Logic LOW or short circuit Optional single wire current share, will allow up to 4 units share within 10%, includes ORing diode MTBF * 80% min at 230 VAC, 70% min for Vo 5V * 3000 VAC Input to Output, 1500 VAC Input to Ground, 250 VDC Output to Ground * 100 kHz PFC, 25 kHz PWM typical * 6.93 W/In3 * Green LED for Power On, Power Good TTL HIGH within 100-500 ms and LOW 1 ms before loss of regulation * 0.5 V to 3 V output voltage denoting 0-100% output current * 100 kHrs min to MIL-HDBK-217F at 25 C, GB Environmental Operating Temperature * 0 C to +70 C, derate from 100% load at +50 C to 50% load at +70 C Cooling * 30 CFM for SMD U-channel versions (SMC Versions have integral fan) Operating Humidity * 5-90%, non-condensing Storage Temperature * -20 C to +85 C Operating Altitude * 3000 m Shock * 15 g (non-operation), 11 ms (half sine wave), 3 times for each axis Vibration * 10-55 Hz (non-operation) 2 g, sweep time 3 mins, 60 mins/axis EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals * FCC Part 15 & CISPR 22 Class B conducted * EN61000-3-2 class A EN61000-3-2 class C for load 40% * EN61000-3-3 * EN61000-4-2, level 3 Perf Criteria A * EN61000-4-3, 3 V/m Perf Criteria A * EN61000-4-4, level 2 Perf Criteria A * EN61000-4-5, installation class 3 Perf Criteria A * EN61000-4-6, 3V Perf Criteria A * EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms Perf Criteria A, B, B * UL60950, CSA C22.2 No. 950, EN60950, CE Mark LVD, SEMI F47 Compliant (high line only) at 100% rated power output Output Voltage(3) Preset 3.3 V 5.0 V 12.0 V 15.0 V 18.0 V 24.0 V 27.0 V 36.0 V 48.0 V 54.0 V 3.3 V 5.0 V 12.0 V 15.0 V 18.0 V 24.0 V 27.0 V 36.0 V 48.0 V 54.0 V Output Power 264 W 400 W 500 W 297 W 450 W 600 W Output Current Maximum Peak(1) 80.00 A 120.00 A 80.00 A 120.00 A 41.67 A 75.00 A 31.00 A 56.00 A 27.78 A 50.00 A 20.83 A 37.50 A 18.50 A 33.33 A 13.89 A 25.00 A 10.42 A 18.75 A 9.25 A 16.67 A 90.00 A 135.00 A 90.00 A 135.00 A 50.00 A 75.00 A 40.00 A 56.00 A 33.00 A 50.00 A 25.00 A 37.50 A 22.22 A 33.33 A 16.67 A 25.00 A 12.50 A 18.75 A 11.10 A 16.67 A Ripple & Noise(2) 75 mV 75 mV 120 mV 150 mV 180 mV 240 mV 270 mV 360 mV 480 mV 540 mV 100 mV 100 mV 120 mV 150 mV 180 mV 240 mV 270 mV 360 mV 480 mV 540 mV Model Number SMC500PS03-C(6) SMC500PS05-C(6) SMC500PS12-C SMC500PS15-C(6) SMC500PS18-C(6) SMC500PS24-C SMC500PS27-C(6) SMC500PS36-C(6) SMC500PS48-C SMC500PS54-C(6) SMC600PS03-C(6) SMC600PS05-C(6) SMC600PS12-C SMC600PS15-C(6) SMC600PS18-C(6) SMC600PS24-C SMC600PS27-C(6) SMC600PS36-C(6) SMC600PS48-C SMC600PS54-C(6) Notes 1. This peak can be taken for 500 s only, average power should not exceed the maximum power. 2. Ripple & Noise is measured using 0.1 F ceramic and 22 F electrolytic capacitor, 20 MHz bandwidth. 3. Alternative output voltages available, consult sales. 4. Load regulation increases to 2% for 0-100% load change. 5. For output currents >50 A, please utilise remote sense to meet regulation ratings. 6. Available for OEM quantities, contact Sales. Options * For U-channel version replace `SMC' in the part number with `SMD' and remove `-C' e.g. SMD600PS12 (See Derating Curve Note 1.) * Constant current limit (95-100%) add suffix `-B' (not available on 3.3 V or 5.0 V models), OEM quantities contact Sales. * Current share and internal ORing diode add suffix `-I' to model number, remote sense not available on `-I' models, OEM quantities contact Sales. * Optional IEC320 inlet replace suffix `-C' with `-D'. Not available for SMD models. Load (%) Derating Curve 100 90 80 70 60 50 40 30 20 10 0 0 10 Notes 1. SMD units require 30 CFM forced air cooling. 20 30 40 50 Ambient Temperature (C) 60 70 80 ACDC SMC/SMD Series Models and Ratings SMC with integral fan All dimensions are in inches (mm) Weight: 3.30 lbs (1.5 kg) approx. Tolerance: 0.012 (0.3 mm) 2.00 (50.8) 2.50 (63.5) A B B 2.09 (53.0) A 1.59 (40.4) 5.00 (127.0) CN3 Pin 7 1.59 (40.3) FAN B 0.59 (15.0) L N IEC320 or equivalent `-D' Option B 1.75 (44.45) 1.62 0.32 (8.25) (41.25) 2.50 (63.6) B B A A 1.25 (31.9) Terminal Block M3 Screw 3 Pins 8.25 mm center B Mounting Hole 8 Places 0.88 (22.25) A 4.25 (108.0) Voltage Trim Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center 9.17 (233.0) A Mounting Hole 8 Places 2.50 (63.5) Pin 1 A A VO- 2.50 (63.5) 6.00 (152.4) VO+ 2.50 (63.5) B B 2.50 (63.5) A Pin 1 2 3 4 5 6 7 2.00 (50.8) 0.22 (5.6) 0.22 (5.6) M4 (Zn (yellow) -plated) 9.17 (233.0) 0.25 (6.4) 0.07 (1.9) 0.02 (0.6) 0.02 (0.6) 0.25 (6.4) 0.07 (1.9) UNC6-32 (Zn-plated) SMD UChannel All dimensions are in inches (mm) Weight: 3.09 lbs (1.4 kg) approx. Tolerance: 0.012 (0.3 mm) 2.00 (50.8) A B B 1.50 (38.1) CN3 (Signals) Function Current monitor Current share(3) Return Power good Remote On/Off -Remote sense +Remote sense 2.50 (63.5) A 1.00 (25.4) 5.00 (127.0) CN3 Pin 7 1.00 (25.4) 6.00 (152.4) 2.50 (63.5) FAN 2.50 (63.5) 0.92 (23.25) A B B 1.75 (44.45) N L 0.37 (9.5) 2.50 (63.5) B 1.29 (32.78) Recommended Air Flow Voltage Trim B 0.92 (23.25) 8.00 (203.20) A B Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center B 2.50 (63.5) A 2.00 (50.8) Notes 1. 2. 3. 4. 5. 0.37 (9.5) 4.33 (110.0) A A Pin 1 A 1.29 (32.78) VO- Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center VO+ ACDC SMC/SMD Series Mechanical Details Logic connector CN3 mates with JST XHP-7 or equivalent and JST SXH-002T-P0.6 crimp terminals. Fan connector mates with JST XHP-2 or equivalent and JST SXH-002T-P0.6 crimp terminals. Output is 12 VDC/160 mA Current share not available with constant current models. Maximum mounting screw penetration: 0.2 (5.00) on bottom side and 0.25 (6.30) on both sides. Maximum screw terminal torque: Input: 7 lbin (0.8 Nm), Output: 15.7 lbin (1.8 Nm) Pin 1 2 3 4 5 6 7 CN3 (Signals) Function Current monitor Current share(3) Return Power good Remote On/Off -Remote sense +Remote sense Remote Sense Output + CN3 Pin 7 Sense + CD + Twisted Pair Supply LOAD CL CN3 Pin 6 Sense - Output - CD Note: 1. CL is 47 F electrolytic capacitor. 2. CD is 0.1 F ceramic capacitor. Remote On/Off PSU CN3 Pin 5, control connector ON/OFF CN3 Pin 3, control connector Return Note: 1. Applying <0.3 V or short between pins 5 and 3 turns the output OFF. 2. Applying >4.5 V or open circuit between pins 5 and 3 turns output ON. Power Good +5 V 1K POWER GOOD CN3 Pin 4, control connector DC OK CN3 Pin 3, control connector Return POWER NOT GOOD Parallel Connection with Current Share Option Supply 1 Output Return CN3 Pin 2 Current Share V1 LOAD Com Supply 2 Output Return CN3 Pin 2 Current Share 25-June-10 ACDC SMC/SMD Series Application Notes