Basic Switch Z
General Purpose Basic Switch
■High precision basic switch in a variety
of styles
■Wide margins of operating conditions
increase the operating speed range
■Available in general purpose and drip-
proof types
Ordering Information
Pin plunger Slim spring Short spr ing Spring Panel mount Panel mount Panel mount
plunger plunger plunger plunger roller plunger cross roller plunger
Hinge lever Low-force Low-force wire Short hinge Hinge roller Unidirectional Flexible rod
hinge lever hinge lever roller lever lever short hinge
roller lever
Operating Part Number
Actuator Characteristics Rated Current Solder Terminal Screw Terminal
Pin plunger 15 A Z-15G Z-15G-B
Slim spring plunger 15 A Z-15GS Z-15GS-B
Shor t spring plunger Low OP 15 A Z-15GD Z-15GD-B
Panel mount plunger Middle OP 15 A Z-15GQ Z-15GQ-B
Panel mount roller plunger 15 A Z-15GQ22 Z-15GQ22-B
Panel mount cross roller plunger 15 A Z-15GQ21 Z-15GQ21-B
Hinge lever Low OF 15 A Z-15GW Z-15GW-B
Low-force hinge lever 15 A Z-15GW4 Z-15GW4-B
Shor t hinge roller lever 15 A Z-15GW22 Z-15GW22-B
Hinge roller lever Parallel 15 A Z-15GW2 Z-15GW2-B
Unidirectional shor t hinge roller lever Low OF 15 A Z-15GW2277 Z-15GW2277-B
GENERAL PURPOSE TYPE
Standard
GENERAL PURPOSE
2
Z Z
Operating Part Number
Actuator Characteristics Rated Current Solder Terminal Screw Terminal
Pin plunger 15 A — Z-15H-B
Low-force hinge lever 15 A — Z-15HW24-B
Low-force, wire hinge lever Low OF 15 A Z-15HW78 Z-15HW78-B
Shor t hinge roller lever 15 A — Z-15HW22-B
GENERAL PURPOSE TYPE
High-sensitivity
Operating Rated Contact Par t Number
Actuator Characteristics Current Gap Solder Terminal Screw Terminal
Slim spring plunger 15 A 0.5 mm Z-15GS55 Z-15GS55-B
Shor t spring plunger 15 A 0.5 mm Z-15GD55 Z-15GD55-B
Spring plunger Middle OP 15 A 0.5 mm Z-15GK55 Z-15GK55-B
High OP 15 A 0.5 mm Z-15GK355 Z-15GK355-B
Panel mount plunger Middle OP 15 A 0.5 mm Z-15GQ55 Z-15GQ55-B
Panel mount roller plunger 15 A 0.5 mm — Z-15GQ2255-B
Panel mount cross roller plunger 15 A 0.5 mm — Z-15GQ2155-B
Hinge lever Low OF 15 A 0.5 mm Z-15GW55 Z-15GW55-B
Shor t hinge roller lever 15 A 0.5 mm Z-15GW2255 Z-15GW2255-B
Hinge roller lever Parallel 15 A 0.5 mm Z-15GW255 Z-15GW255-B
Flexible rod High OF 15 A 0.5 mm Z-15GNJ55 Z-15GNJ55-B
DRIP-PROOF TYPE
Standard
Operating Rated Contact Par t Number
Actuator Characteristics Current Gap Solder Terminal Screw Terminal
Panel mount plunger Middle OP 15 A 0.25 mm — Z-15HQ55-B
Flexible rod High OF 15 A 0.25 mm — Z-15HNJS55-B
DRIP-PROOF TYPE
High-sensitivity
Note: For smaller mounting hole types, please consult OMRON.
Type Contact gap Features
General purpose H: 0.25 mm Pin plunger and lever types available.
(high sensitivity) Drip-proof and flexible rod types are also available.
G: 0.5 mm (standard)
Drip-proof H: 0.25 mm The pin plunger is sealed from the other switch mechanisms by a resilient rubber,
(high sensitivity) and the case and cover are sealed by adhesive so that the switch is resistant to
G: 0.5 mm (standard) humidity, oil and dust. The degree of protection conforms to IEC IP63.
■BASIC CONTACT FORM
Basic Contact form
3
Z Z
Non-inductive load (A) Inductive load (A)
Contact Rated Resistive load Lamp load Inductive load Motor load Inrush current (A)
gap voltage NC NO NC NO NC NO NC NO NC NO
G,H 125 VAC 15 (10) — 3 1.5 15 (10) — 5 2.5 30 max. 15 max.
250 VAC 15 (10) — 2.5 1.25 15 (10) — 3 1.5
500 VAC 10 — 1.5 0.75 6 — 1.5 0.75
G 8 VDC 15 — 3 1.5 15 — 5 2.5
14 VDC 15 — 3 1.5 10 — 5 2.5
30 VDC 6 — 3 1.5 5 — 5 2.5
125 VDC 0.5 — 0.5 0.5 0.05 — 0.05 0.05
250 VDC 0.25 — 0.25 0.25 0.03 — 0.03 0.03
H 8 VDC 15 — 3 1.5 15 — 5 2.5
14 VDC 15 — 3 1.5 10 — 5 2.5
30 VDC2—21.41—11
125 VDC 0.4 — 0.4 0.4 0.03 — 0.03 0.03
250 VDC 0.2 — 0.2 0.2 0.02 — 0.02 0.02
Specifications
Standard type (except flexible rod types)
Non-inductive load (A) Inductive load (A)
Rated Resistive load Lamp load Inductive load Motor load Inrush current (A)
voltage NC NO NC NO NC NO NC NO NC NO
125 VAC 15 — 217—2.5230 max. 15 max.
250 VAC 15 — 1 0.5 5 — 1.5 1
8 VDC 15—217—31.5
14 VDC 15—217—31.5
30 VDC 2—211—10.5
125 VDC 0.4 — 0.4 0.4 0.03 — 0.03 0.03
250 VDC 0.2 — 0.2 0.2 0.02 — 0.02 0.02
Standard flexible rod types
■CONSTRUCTION
Drip-proof type
Rubber cap protects the built-in switch from
water and dust
Fixed contact (NC)
Glued surface (adhesive is filled between
case and cover)
Movable contact
Fixed contact (NC)
Movable spring
Spring pivot
4
Z Z
Standard Standard flexible rod types
(except flexible rod types) (coil spring and steel wire type)
Operating speed 0.01 mm to 1 m/second (see note 2) 1 mm to 1 m/second
Operating frequency Mechanical 240 operations/min. 120 operations/min.
Electrical 20 operations/min. 20 operations/min.
Insulation resistance 100 MΩ min. (at 500 VDC)
Contact resistance 50 mΩ max. (initial) 15 mΩ max. (initial)
Dielectric strength (VAC) G contact gap model
1,000 VAC, 50/60 Hz for 1 minute between terminals of same polar ity
H contact gap model 600 VAC, 50/60 Hz for 1 minute
2,000 VAC, 50/60 Hz for 1 minute between current carrying metal parts and
ground and between each terminal and non-current carrying metal parts
Vibration Malfunction 10 to 55 Hz, 1.5 mm 10 to 20 Hz, 1.5 mm
double amplitude (see note 4) double amplitude
Shock Mechanical durability 1,000 m/s2 min. (approx. 100 g)
Malfunction 300 m/s2 min. (approx. 30 g) (see note 3) 50 m/s2 min. (approx. 5 g)
Ambient temperature Standard types -25° to 80°C (with no icing)
Drip-proof types -15° to 80°C (with no icing)
Humidity Standard types 35% to 85% RH
Drip-proof types 35% to 95% RH
Ser vice life Mechanical G, H contact gap models 1,000,000 operations min.
20,000,000 operations min. (see note 4)
Electrical G, H contact gap models 100,000 operations min.
500,000 operations min. (see note 2)
Weight Approx. 22 to 58 g Approx. 42 to 48 g
Characteristics
■ACCESSORIES (order separately)
ZAA-1 ZAA-2
Characteristics w/Z-15G-B w/Z-15G-B
OF max. 500 g 500 g
RF min. 170 g 170 g
PT max. — —
OT min. 12.7 mm 12.7 mm
MD max. 2.2 mm 2.2 mm
FP max. 34.5 mm 46.1 mm
OP 28.9±1.6 mm 40.4±1.6 mm
Operating Characteristics (when used with Z-15)
Material Mounting method For solder terminal For screw terminal Remar ks
Phenolic resin Side mounting AP-A AP-B —
Metal Side mounting AP1-A AP1-B Use in conjunction with AP-A and AP-B
Polyvinyl chloride Side mounting AP-Z AP-Z Excels in safety and dust-proofing property
Terminal enclosures - Standard models
Note: 1. Data shown are of initial value.
2. Apply to the pin plunger models or the pin plunger of the lever models.
3. Apply to Z-15G.
4. Apply to the pin plunger models.
5
Z Z
■CHARACTERISTIC DATA
Mechanical service life Electrical service life
Z-15G Z-15G
Number of operations (x106)
Number of operations (x104)
Overtravel (mm) Switching current (A)
6
Z Z
Dimensions
Z-15G-B, Z-15H-B
Operating
characteristics Z-15G-B Z-15H-B
OF 250 to 350 g 200 to 280 g
RF min. 114 g 114 g
PT max. .4 mm (0.02) .3 mm (0.01)
OT min. .13 mm (0.01) .13 mm (0.01)
MD max. .05 mm (0.002) .025 mm (0.001)
OP 15.9 ± 0.4 mm 15.9 ± 0.4 mm
(0.63 ± 0.02) (0.63 ± 0.02)
Unit: mm (inch)
Operating
characteristics Z-15GS-B
OF 250 to 350 g
RF min. 114 g
PT max. 0.4 mm (0.02)
OT min. 1.6 mm (0.06)
MD max. 0.05 mm (0.002)
OP 28.2 ± 0.5 mm
(1.1 ± 0.02)
Z-15GS-B
Operating
characteristics Z-15GD-B
OF 250 to 350 g
RF min. 114 g
PT max. 0.4 mm (0.02)
OT min. 1.6 mm (0.06)
MD max. 0.05 mm (0.002)
OP 21.5 ± 0.5 mm
(0.85 ± 0.02)
Z-15GD-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
7
Z Z
Operating
characteristics Z-15GQ-B
OF 250 to 350 g
RF min. 114 g
PT max. 0.4 mm (0.02)
OT min. 5.5 mm (0.22)
MD max. 0.05 mm (0.002)
OP 21.8 ± 0.8 mm
(0.86 ± 0.03)
Z-15GQ-B
Operating
characteristics Z-15GQ22-B
OF 250 to 350 g
RF min. 114 g
PT max. 0.4 mm (0.02)
OT min. 3.58 mm (0.14)
MD max. 0.05 mm (0.002)
OP 33.4 ± 1.2 mm
(1.31 ± 0.05)
Z-15GQ22-B
Operating
characteristics Z-15GQ21-B
OF 250 to 350 g
RF min. 114 g
PT max. 0.4 mm (0.02)
OT min. 3.58 mm (0.14)
MD max. 0.05 mm (0.002)
OP 33.4 ± 1.2 mm
(1.31 ± 0.05)
Z-15GQ21-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
8
Z Z
Operating
characteristics Z-15GW-B
OF max. 70 g
RF min. 14 g
OT min. 5.6 mm (0.22)
MD max. 1.27 mm (0.05)
FP max. 28.2 mm (1.11)
OP 19 ± 0.8 mm
(0.75 ± 0.03)
Z-15GW-B
Operating
characteristics Z-15GW4-B
OF max. 28 g
RF min. 3.5 g
PT max. 10 mm (0.39)
OT min. 5.6 mm (0.22)
MD max. 1.27 mm (0.05)
OP 19 ± 0.8 mm
(0.75 ± 0.03)
Z-15GW4-B
Operating
characteristics Z-15HW24-B
OF max. 6 g
RF min. 0.5 g
PT max. 19.8 mm (0.78)
OT min. 10 mm (0.39)
MD max. 2 mm (0.08)
OP 19.8 ± 1.6 mm
(0.75 ± 0.03)
Z-15HW24-B
Operating
characteristics Z-15HW78-B
OF max. 4 g
RF min. 0.3 g
PT max. 10 mm (0.39)
OT min. 6 mm (0.24)
MD max. 3 mm (0.12)
OP 20 ± 1 mm
(0.79 ± 0.04)
Z-15HW78-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
Unit: mm (inch)
9
Z Z
Z-15GW22-B, Z-15HW22-B
Operating
characteristics Z-15GW22-B Z-15HW22-B
OF max. 160 g 150 g
RF min. 42 g 42 g
OT min. 2.4 mm (0.09) 2.4 mm (0.09)
MD max. 0.5 mm (0.02) 0.45 mm (0.02)
FP max. 32.5 mm (1.28) 32.5 mm (1.28)
OP 30.2 ± 0.4 mm 30.2 ± 0.4 mm
(1.19 ± 0.02) (1.19 ± 0.02)
Operating
characteristics Z-15GW2-B
OF max. 100 g
RF min. 22 g
OT min. 4 mm (0.16)
MD max. 1.02 mm (0.04)
FP max. 36.5 mm (1.44)
OP 30.2 ± 0.8 mm
(1.19 ± 0.03)
Z-15GW2-B
Operating
characteristics Z-15GW2277-B
OF max. 170 g
RF min. 42 g
OT min. 2.4 mm (0.09)
MD max. 0.51 mm (0.02)
FP max. 43.6 mm (1.72)
OP 41.3 ± 0.8 mm
(1.63 ± 0.03)
Z-15GW2277-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
10
Z Z
Operating
characteristics Z-15GS55-B
OF max. 540 g
RF min. 114 g
PT max. 1.9 mm (0.07)
OT min. 1.6 mm (0.06)
MD max. 0.06 mm (0.002)
OP 28.2 ± 0.5 mm
(1.11 ± 0.02)
Operating
characteristics Z-15GD55-B
OF max. 540 g
RF min. 114 g
PT max. 1.8 mm (0.07)
OT min. 1.6 mm (0.06)
MD max. 0.06 mm (0.002)
OP 21.5 ± 0.5 mm
(.85 ± 0.02)
Z-15GD55-B
Operating
characteristics Z-15GK55-B
OF max. 540 g
RF min. 114 g
PT max. 2.3 mm (0.09)
OT min. 1.6 mm (0.06)
MD max. 0.06 mm (0.002)
OP 28.2 ± 0.5 mm
(1.11 ± 0.02)
Z-15GK55-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
Unit: mm (inch)
Z-15GS55-B
11
Z Z
Operating
characteristics Z-15GK355-B
OF max. 540 g
RF min. 114 g
PT max. 2.4 mm (0.09)
OT min. 3.5 mm (0.14)
MD max. 0.06 mm (0.002)
OP 37.8 ± 1.2 mm
(1.49 ± 0.05)
Z-15GK355-B
Z-15GQ55-B, Z-15HQ55-B
Operating
characteristics Z-15GQ55-B Z-15GH55-B
OF max. 540 g 400 g
RF min. 114 g 114 g
PT min. 1.8 mm (0.07) 1.7 mm (0.07)
OT min. 5.5 mm (0.22) 5.5 mm (0.22)
MD max. 0.06 mm (0.002) 0.04 mm (0.002)
OP 21.8 ± 0.8 mm 21.8 ± 0.8 mm
(0.86 ± 0.03) (0.86 ± 0.03)
Operating
characteristics Z-15GQ2255-B
OF max. 540 g
RF min. 114 g
PT max. 1.8 mm (0.07)
OT min. 3.58 mm (0.14)
MD max. 0.06 mm (0.002)
OP 33.4 ± 1.2 mm
(1.31 ± 0.05)
Z-15GQ2255-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
12
Z Z
Operating
characteristics Z-15GQ2155-B
OF max. 540 g
RF min. 114 g
PT max. 1.8 mm (0.07)
OT min. 3.58 mm (0.14)
MD max. 0.06 mm (0.002)
OP 33.4 ± 1.2 mm
(1.31 ± 0.05)
Z-15GQ2155-B
Operating
characteristics Z-15GW55-B
OF max. 100 g
RF min. 14 g
OT min. 5.6 mm (0.22)
MD max. 2 mm (0.08)
FP max. 28.2 mm (1.11)
OP 19 ± 0.8 mm
(0.75 ± 0.03)
Z-15GW55-B
Operating
characteristics Z-15GW2255-B
OF max. 200 g
RF min. 42 g
OT min. 2.44 mm (0.10)
MD max. 0.8 mm (0.03)
FP max. 32.9 mm (1.30)
OP 30.2 ± 0.4 mm
(1.19 ± 0.02)
Z-15GW2255-B
Operating
characteristics Z-15GW255-B
OF max. 130 g
RF min. 21 g
OT min. 4 mm (0.16)
MD max. 1.6 mm (0.06)
FP max. 36.5 mm (1.44)
OP 30.2 ± 0.8 mm
(1.19 ±0.03)
Z-15GW255-B
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
Unit: mm (inch)
13
Z Z
Operating
characteristics Z-15GNJ55-B
OF max. 50 g
PT max. 20 mm* (0.79)
Z-15GNJ55-B
* Reference value
Operating
characteristics Z-15HNJ55-B
OF max. 15 g
PT max. 25 mm* (0.98)
Z-15HNJS55-B
* Reference value
Note: 1. Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
2. For smaller diameter mounting holes, please consult OMRON.
3. All drawings show the switches with screw terminals. For solder terminals, remove the “-B” from the end of the part number.
14
Z Z
■TERMINALS
Solder terminal (blank) Screw terminal (B)
■MOUNTING HOLES
Side mounting Panel mounting plunger type Roller plunger type
Unit: mm (inch)
■MOLDED TERMINAL TYPE
ORDERING INFORMATION
The solder terminal type can be supplied with
molded terminals with a choice of five different lead
outlet directions. When placing your order for the
molded terminal type, add the following code to the
model number.
-M■■■■
Note: 1. Standard leads are single-core vinyl cords (VSF) with a nominal cross sectional area of 1.25 mm2.
2. Standard vinyl cord lengths are 1 m, 3 m, and 5 m.
3. Mold thickness will be 19 mm when using VCT cords.
4. Standard unit has three lead outlets in the same direction.
5. Connect the black lead to the COM terminal, white lead to the NO terminal, and red lead to the NC terminal, respectively.
■DIRECTIONS OF LEAD OUTLETS
The following diagrams show the molded terminal version of sealed type Z-15GW2255, with a mold thickness of 12 mm.
Z-15GW2255-ML Z-15GW2255-MF Z-15GW2255-MR Z-15GW2255-MH Z-15GW2255-MD
(left-hand) (forward) (right-hand) (rearward) (underside)
Note: Respective directions of lead outlets are determined with the plunger viewed on your left.
Nominal cross- Finished outer Connection to
Type sectional area (mm2) diameter (mm) ter minal Length (m)
VSF (single-core, vinyl cord) 1.25 Approx. 3.1 Black-COM 0.5, 1, 2, 3, 5
VCT (vinyl-insulated cable) Approx. 9.6 (2-core) White-NO (standard)
Approx. 10.5 (3-core) Red-NC
■LEAD WIRE SPECIFICA TIONS
Lead outlet directions
(L, R, D, F, H)
Mold thickness
(No symbol)…a = 12 mm
with VSF
19…a = 19 mm with VCT
Three M4 x 5.5 dia.
Terminal screws
(with tooth washers)
15
Z Z
■ACCESSORIES, order separately
Hinge lever Hinge roller lever
ZAA-1 ZAA-2
Note: Unless otherwise specified, a tolerance of ± 0.8 mm applies to all dimensions.
Panel mount plunger
ZAQ-2
Operating
characteristics
ZAQ-2 with Z-15G
OF max. 550 g
RF min. 144 g
RT max. 1 mm (0.04 in)
OT min. 4.5 mm (0.18 in)
MD max. 0.2 mm (0.01 in)
OP 53.2±1.5 mm
(2.09±0.06 in)
Panel mount plunger
ZAQ-3
Operating
characteristics
ZAQ-3 with Z-15G
OF max. 550 g
RF min. 144 g
RT max. 1 mm (0.04 in)
OT min. 4.5 mm (0.18 in)
MD max. 0.2 mm (0.01 in)
OP 27.8±1.5 mm
(1.09±0.06 in)
16
Z Z
Panel mount plunger
ZAQ-1
Operating
characteristics
ZAQ-1 with Z-15G
OF max. 550 g
RF min. 144 g
RT max. 1 mm (0.04 in)
OT min. 20.4 mm (0.80 in)
MD max. 0.2 mm (0.01 in)
OP 69.1±1.5 mm
(2.72±0.06 in)
AP-A (for solder terminal) AP1-A (for solder terminal) AP-B (for screw terminal)
AP1-B AP-Z
Note: Unless otherwise specified, a tolerance of ± 0.4 mm applies to all dimensions.
Note: Unless otherwise specified, a tolerance of ± 0.8 mm applies to all dimensions.
17
Z Z
■CABLE OUTLET DIMENSIONS
A-A section B-B section
Note: The cable outlet is provided with two stepped openings (6 dia. and 8 dia.) to permit the use of either opening according to the
finished OD of the cable to be connected.
■APPROVALS
UL (File No. E41515)/CSA (File No. LR21642)/SEV (File No. S20/163)
Type Rating
Z-15 Series 15 A 125, 250 or 480 VAC
1/2 A 125 VDC, 1/4 A 250 VDC
1/8 HP 125 VAC, 1/4 A 250 VAC
Note: The rated values approved by each of the safety standards (e.g. UL/CSA) may be different from the performance characteristics
individually defined in this catalog.
Precautions
■OPERATION
High sensitivity switch (Z-15H)
When using the switch in a DC circuit, be sure to provide an arc
suppressor as well because the small contact gap of the switch
may result in contact troubles.
In an application where a high repeat accuracy is required, limit
the current that flows through the switch to within 0.1 A. Also,
use a relay to control a high-capacity load if the switch is
connected to such a load. (In this case, the current of the relay
coil is the load of the switch.)
Do not apply a force of 2 kg or higher to the pin plunger.
Exercise care that the environment conditions such as
temperature and humidity do not change abruptly.
Drip-proof type (Z-■■55)
The switch is not perfectly oil-tight; so, do not dip it in oil or
water.
Depending on the environments, the materials of the rubber
boots must be selected. Oil-tight, cold-resistive, and heat-
resistive rubbers are available from OMRON.
Flexible rod type (Z-15■■NJ■■55) (drip-proof type)
When the rod is fully swung, the switch may operate when the
lever returns, causing chattering. Use a circuit that
compensates for chattering wherever possible.
Do not switch the rod to the fullest extent when the switch is to
break a power circuit because such a practice may cause metal
deposition to occur between the mating contacts of the switch.
■MOUNTING
Use M4 mounting screws with plain washers or spring washers
to mount the switch. Tighten the screws at a torque of 12 to 15
kg-cm.
Solder the lead to the terminal by applying a soldering iron
rated at 60 W max. quickly (within 5 seconds). Note that
applying a soldering iron for too long a time or using one that is
rated at more than 60 W may degrade the switch
characteristics.
Panel mount type (Z-15■■Q)
When mounting a panel mount type switch (the one having a
suffix “-Q” in its model number) to a panel, tighten the hexagon
nut of the actuator at a torque of 50 kg-cm or less.
When mounting a panel mount type switch on its side, remove
the hexagon nut from the actuator and carefully adjust the dog
angle and operating speed because too large a dog angle or
too high an operating speed may damage the switch. Especially
be careful not to apply an impulsive force to the actuator when
operating it. By the same token, too high an operating speed
and too long an overtravel may damage a panel mount switch
with a roller pin plunger.
Do not use mounting holes of the switch body when mounting
on panel with M12 mounting nut.
18
Z Z
OMRON ELECTRONICS, INC. OMRON CANADA, INC.
One East Commerce Drive 885 Milner Avenue
Schaumburg, IL 60173 Scarborough, Ontario M1B 5V8
1-800-55-OMRON 416-286-6465
Cat. No. GC SW5 4/98 Specifications subject to change without notice. Printed in the U.S.A.
