ACD2202 CATV/TV/Video Downconverter with Dual Synthesizer Data Sheet - Rev 2.1 FEATURES * Integrated Downconverter * Integrated Dual Synthesizer * 256 QAM Compatibility * Single +5 V Power Supply Operation * Low Power Consumption: <0.6 W * Low Noise Figure: 8 dB * High Conversion Gain: 10 dB * Low Distortion: -53 dBc * Three-Wire Interface * Small Size * -40 C to +85 C APPLICATIONS * Set Top Boxes * CATV Video Tuners * Digital TV Tuners * CATV Data Tuners * Cable Modems S8 Package 28 Pin SSOP PRODUCT DESCRIPTION The ACD2202 uses both GaAs and Si technology to provide the downconverter and dual synthesizer functions in a double conversion tuner gain block, local oscillator, balanced mixer and dual synthesizer. The specifications meet the requirements of CATV/TV/Video and Cable Modem Data applications. The ACD2202 is supplied in a 28 lead SSOP package and requires a single +5 V supply voltage. The IC is well suited for applications where small size, low cost, low auxiliary parts count and a nocompromise performance is important. It provides for cost reduction by lowering the component and packaged IC count and decreasing the amount of labor-intensive production alignment steps, while significantly improving performance and reliability. RFD VIF+IFOUT+ RFIN+ RFINLow Noise VGA VIF+IFOUT- 18 Bit RF2 N Counter RF2 Phase Detector RF2 Charge Pump CPD RF1 Phase Detector RF1 Charge Pump CPU 15 Bit RF2 R Counter REFIN REFOUT Oscillator Mixer 15 Bit RF1 R Counter RFU Phase Splitter TCKT RF2: 64/65 Prescaler OSC OUT Clock Data Enable Figure 1: Downconverter Block Diagram RF1: 64/65 Prescaler 18 Bit RF1 N Counter 22 Bit Data Registar Figure 2: Dual Synthesizer Block Diagram 12/2003 ACD2202 1 RFIN+ VIF + IFOUT+ 28 2 RFIN- VIF + IFOUT- 27 3 GND GND 26 4 ISET VSUP 25 5 TCKT OSCOUT 24 6 OSCGND GND 23 7 OSCGND GND 22 8 VSS VSS 21 9 VSS VSS 20 10 EN RFD 19 11 DATA CPD 18 12 CLK CPU 17 13 REFIN RFU 16 14 REFOUT VSYN 15 Figure 3: Pinout 2 Data Sheet - Rev 2.1 12/2003 ACD2202 Table 1: Pin Description PIN NAME DESCRIPTION PIN NAME DESCRIPTION VIF+IFOUT+ Downconverter Differential IFOutput Inductively coupled to +VDD 27 VIF+IFOUT - Downconverter Differential IFOutput Inductively coupled to +VDD Downconverter Ground (Must be connected) 26 GND Downconverter Ground (Must be connected) ISET Downconverter Gilbert Cell Current Source Resistor 25 VSUP Oscillator and Phase Splitter Supply (+VDD) TCKT Oscillator Input Port (Tank circuit connection) 24 OSCOUT Oscillator Output (Connected to Synthesizer RF Input) 6 OSCGND Oscillator Tank Circuit Ground (Not to be connected to any other circuit ground) 23 GND Downconverter Ground (Must be connected) 7 OSCGND Same as Pin 6 22 GND Downconverter Ground (Must be connected) 8 V SS Synthesizer Ground (Required) 21 V SS Synthesizer Ground (Required) 9 V SS Synthesizer Ground (Required) 20 V SS Synthesizer Ground (Required) 10 EN 3-Wire Interface Enable 19 RFD Synthesizer Downconverter RFInput 11 DATA 3-Wire Interface Data 18 C PD Synthesizer Downconverter Charge Pump Output 12 C LK 3-Wire Interface Clock 17 C PU Synthesizer Upconverter Charge Pump Output 13 REFIN Crystal Reference Input 16 RFU Synthesizer Upconverter RFInput 14 REFOUT Crystal Reference Output 15 VSYN Synthesizer Supply (+VDD) RFIN+ Downconverter Differential RFInput 2 RFIN- Downconverter Differential RFInput 3 GND 4 5 1 28 Data Sheet - Rev 2.1 12/2003 3 ACD2202 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (pins 25, 27 & 28) (pin 15) - +9 +6.5 VD C Voltage on pins 10 through 14, 16 through 19 with VSS = 0 V -0.3 VSYN +0.3 VD C Input Voltages (pins 1, 2 & 5) - 0 VD C Input Power - +10 +17 +20 dB m -55 +150 C Soldering Temperature - 260 C Soldering Time - 4 S ec Thermal Impedance, JC - 40 C/W (pins 1 & 2) (pin 5) (pins 13, 16 & 19) Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER Downconverter Frequencies RF Input (RF) IF Output (IF) Local Oscillator (LO) MIN TYP MAX UNIT 900 35 865 - 1200 150 1350 MHz 400 400 2 - 4 - 2100 1400 20 10 MHz +4.70 +5 +5.25 VD C -40 - +85 C (1) Synthesizer Frequencies Upconverter Synthesizer (RFU) Downconverter Synthesizer (RFD) Reference Oscillator (REFIN) Phase Detector Supply Voltage: VDD (pins 15, 25, 27, 28) Ambient Operating Temperature: TA (2) The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) Mixer operation is possible beyond these frequencies with slightly reduced performance. (2) Case Temperature is 15 C higher than Ambient Temperature, when Ambient Temperature is +25 C, using the PC Board Layout shown in Figures 23-25. 4 Data Sheet - Rev 2.1 12/2003 ACD2202 Table 4: Electrical Specifications - Downconverter Section (7) (TA = 25 C , VDD = +5 VDC, RFIN = 1087 MHz, IFOUT = 45 MHz) PARAMETER MIN TYP MAX UNIT Conversion Gain (1) Conversion Gain (2) 8 11 10 13 14 17 dB SSB Noise Figure (2), (3) - 4 7 dB Cross Modulation - -56 -53 dB c - - -53 dB c +12 - - dB m - -90 -85.5 dBc/Hz -10 -5 - dB m Spurious @ IF Output LO Signals and Harmonics Beats Within Output Channel Other Beats from 2 to 200 MHz Other Spurious - -10 -48 -50 -10 - dB m dB c dB m dB m IF Supply Current (pin 27 & 28) (1), (2),(6) - 50 65 mA Osc/Phase Splitter Supply Current (pin 25) - 30 45 mA Power Consumption - 400 550 mW (2), (4), (6) 3rd Order Intermodulation Distortion (IMD3) (2), (5), (6) 2-Tone 3rd Order Input Intercept Point (IIP3) (2), (5), (6) LO Phase Noise (@ 10 KHz Offset) (1), (2) LO Output Power (pin 24) (1), (2) Notes: (1) As measured in ANADIGICS test fixture with single-ended RF input. (2) As measured in ANADIGICS test fixture with differential RF inputs. (3) SSB noise figure will be approximately 3 dB higher with single-ended RF input. (4) Two tones: 1085 and 1091 MHz, -20 dBm each, 1091 MHz tone AM-modulated 99% at 15 kHz. (5) Two tones: 1085 and 1091 MHz, -15 dBm each. (6) R1 = 10 Ohms. (7) Case Temperature is 15 C higher than Ambient Temperature, when Ambient Temperature is +25 C, using the PC Board Layout shown in Figures 23-25. Data Sheet - Rev 2.1 12/2003 5 ACD2202 Table 5: Electrical Specifications - Synthesizer Section (4) (TA = 25 C , VDD = +5 VDC) PARAMETER MIN TYP MAX UNIT Prescalar Input Sensitivity Upconverter: RFU (pin 16) (1) Downconverter: RFD (pin 19) (2) Upconverter: RFU (pin 16) (1) Downconverter: RFD (pin 19) (2) -7 -13 -6 -11 - +20 +20 - Reference Oscillator Sensitivity (pin 13) - 0.5 - Vp-p Charge Pump Output Current (3) SINK SOURCE - 1.25 -1.25 - mA Supply Current - 35 50 mA Power Consumption - 165 250 mW COMMENTS (over operating frequency) dB m TA = +85 C, VDD = +4.7 V TA = +85 C, VDD = +4.7 V Notes: (1) Measured at 250 kHz comparison frequency. (2) Measured at 62.5 kHz comparison frequency. (3) CPU and CPD = VCC/2. (4) Case Temperature is 15 C higher than Ambient Temperature, when Ambient Temperature is +25 C, using the PC Board Layout shown in Figures 23-25. 6 Data Sheet - Rev 2.1 12/2003 ACD2202 Table 6: Digital Interface Specifications (TA = 25 C, VDD = +5 VDC, ref. Figure 4) PARAMETER MIN TYP MAX UNIT Logic High Input: VH (pins 10, 11, 12) 2.0 - - V Logic Low Input: VL (pins 10, 11, 12) - - 0.8 V Logic Input Current Consumption (pins 10, 11, 12) - - 0.01 mA Data to Clock Set Up Time: tCS 50 - - ns Data to Clock Hold Time: tCH 10 - - ns Clock Pulse Width High: tCWH 50 - - ns Clock Pulse Width Low: tCWL 50 - - ns Clock to Load Enable Setup Time: tES 50 - - ns Load Enable Pulse Width: tEW 50 - - ns Rise Time: tR - 10 - ns Fall Time: tF - 10 - ns DATA N20: MSB (R20: MSB) N19 N10 (R19) R10 N9 C2 (R9) (R8) (C2) C1: LSB (C1: LSB) CLOCK tCWL LE OR LE t CS t CH t CWH t ES t EW Figure 4: Serial Data Input Timing Data Sheet - Rev 2.1 12/2003 7 ACD2202 PERFORMANCE DATA 15.0 5.0 13.8 3.63 14.0 4.6 13.6 3.61 13.0 4.2 13.4 3.59 12.0 3.8 Conversion Gain 13.2 Conversion Gain (dB) 3.65 Noise Figure (dB) Conversion Gain (dB) 14.0 13.0 4.8 4.9 5.0 5.1 5.2 3.0 25 5.3 35 55 75 85 Figure 8: Typical Phase Noise at 10 kHz Offset vs. Ambient Temperature (VDD = +5 V, fLO2 = 1042 MHz) -90 -84 -91 -86 -92 -93 -88 -90 -92 -94 -94 -95 4.7 4.8 4.9 5.0 5.1 5.2 25 5.3 35 45 Figure 9: Typical Local Oscillator Output Power vs. Supply Voltage (TA = +25 C, fLO2 = 1042 MHz) -5.0 -5.0 Output Power (dBm) -4.5 -6.0 65 75 85 Figure 10: Typical Local Oscillator Output Power vs. Ambient Temperature (VDD = +5 V, fLO2 = 1042 MHz) -4.5 -5.5 55 Ambient Temperature (C) Supply Voltage (V) Output Power (dBm) 65 Figure 7: Typical Phase Noise at 10 kHz Offset vs. Supply Voltage (TA = +25 C, fLO2 = 1042 MHz) Phase Noise (dBc/Hz) Phase Noise (dBc/Hz) 45 Ambient Temperature (C) Supply Voltage (V) -5.5 -6.0 -6.5 -6.5 -7.0 -7.0 4.7 4.8 4.9 5.0 5.1 5.2 5.3 25 Supply Voltage (V) 8 3.4 Noise Figure 10.0 3.55 4.7 Conversion Gain 11.0 3.57 Noise Figure Noise Figure (dB) Figure 6: Typical Conversion Gain and Noise Figure vs. Ambient Temperature (VDD = +5 V, fLO2 = 1042 MHz) Figure 5: Typical Conversion Gain and Noise Figure vs. Supply Voltage (TA = +25 C, fLO2 = 1042 MHz) Data Sheet - Rev 2.1 12/2003 35 45 55 Ambient Temperature (C) 65 75 85 ACD2202 Figure 12: Typical Downconverter Prescaler Sensitivity vs. Local Oscillator Frequency (TA = +25 C, VDD = +5 V) -5 -12 -10 -14 Prescalar Sensitivity (dBm) Prescalar Sensitivity (dBm) Figure 11: Typical Upconverter Prescaler Sensitivity vs. Local Oscillator Frequency (TA = +25 C, VDD = +5 V) -15 -20 -25 -30 -35 500 700 900 1100 1300 1500 1700 1900 -16 -18 -20 -22 -24 400 2100 600 800 LO1 Frequency (MHz) 1400 -16.0 Prescalar Sensitivity (dBm) -7.0 Prescalar Sensitivity (dBm) 1200 Figure 14: Typical Downconverter Prescaler Sensitivity vs. Supply Voltage (TA = +25 C, fLO2 = 1000 MHz) Figure 13: Typical Upconverter Prescaler Sensitivity vs. Supply Voltage (TA = +25 C, fLO1 = 2100 MHz) -7.5 -8.0 -8.5 -9.0 4.7 4.8 4.9 5.0 5.1 5.2 -16.5 -17.0 -17.5 -18.0 5.3 4.7 4.8 4.9 Supply Voltage (V) 5.0 5.1 5.2 5.3 Supply Voltage (V) Figure 15: Typical Upconverter Prescaler Sensitivity vs. Ambient Temperature (VDD = +5 V, fLO1 = 2100 MHz) Figure 16: Typical Downconverter Prescaler Sensitivity vs. Ambient Temperature (VDD = +5 V, fLO2 = 1000 MHz) -6.0 -15.0 Prescalar Sensitivity (dBm) Prescalar Sensitivity (dBm) 1000 LO2 Frequency (MHz) -6.5 -7.0 -7.5 -8.0 -15.5 -16.0 -16.5 -17.0 -17.5 -8.5 25 35 45 55 65 75 85 25 35 45 55 65 75 85 Ambient Temperature (C) Ambient Temperature (C) Data Sheet - Rev 2.1 12/2003 9 ACD2202 Figure 17: Typical Conversion Gain and Noise Figure vs. LNA/Mixer Current Control Resistor R1 (TA = +25 C, VDD = +5 V, fLO2 = 1042 MHz) 15 5.0 Conversion Gain 200 180 13 4.2 12 3.8 11 3.4 10 Current (mA) 4.6 Noise Figure N o is e F ig u re (d B ) 14 C o n v e rs io n G a in (d B ) Figure 18: Typical Total Current Consumption vs. LNA/Mixer Current Control Resistor R1 (TA = +25 C, VDD = +5 V) 5 10 15 20 140 120 100 3.0 0 160 80 25 0 5 10 Figure 19: Typical Input IP3 vs. LNA/Mixer Current Control Resistor R1 (TA = +25 C, VDD = +5 V) 25 -50 Cross Modulation (dBc) 17 IIP3 (dBm) 20 Figure 20: Typical Cross Modulation vs. LNA/Mixer Current Control Resistor R1 (TA = +25 C, VDD = +5 V) 19 15 13 11 9 0 5 10 15 20 25 -55 -60 -65 0 R1 Resistor Value ( ) 10 15 R1 Resistor Value ( ) R1 Resistor Value ( ) 5 10 R1 Resistor Value ( ) Data Sheet - Rev 2.1 12/2003 15 20 ACD2202 LOGIC PROGRAMMING Synthesizer Register Programming The ACD2202 includes two PLL synthesizers. Each synthesizer contains programmable Reference and Main dividers, which allow a wide range of local oscillator frequencies. The 22-bit registers that control the dividers are programmed via a shared three-wire bus, consisting of Data, Clock and Enable lines. Table 7: Register Select Bits S E LE C T BITS The data word for each register is entered serially in order with the most significant bit (MSB) first and the least significant bit (LSB) last. The rising edge of the Clock pulse shifts each data value into the register. The Enable line must be low for the duration of the data entry, then set high to latch the data into the register. (See Figure 4.) S 1 0 0 Reference Divider Register for PLL2 0 1 Main Divider Register for PLL2 1 0 Reference Divider Register for PLL1 1 1 Main Divider Register for PLL1 Table 8: Reference Divider Registers MSB 21 20 19 18 17 16 15 Program Mode D 5 S 2 Reference Divider Programming The reference divider register for each synthesizer consists of fifteen divider bits, five program mode bits and the two register select bits, as shown in Table 8. The fifteen divider bits allow a divide ratio from 3 to 32767, inclusive, as shown in Table 9. Register Select Bits The two least significant bits of each register are register select bits that determine which register is programmed during a particular data entry cycle. Table 7 indicates the register select bit settings used to program each of the available registers. 22 DESTINATION REGISTER FOR SERIAL DATA D 4 D 3 D 2 14 13 12 11 10 9 8 LSB 7 6 5 4 3 Reference Divider Divide Ratio, R D 1 R 15 R 14 R 13 R 12 R 11 R 10 R 9 R 8 R 7 R 6 R 5 2 1 Select R 4 R 3 R 2 R 1 S 2 S 1 Table 9: Reference Divider R Counter Bits DIVIDE RATIO R R 15 R 14 R 13 R 12 R 11 R 10 R 9 R 8 R 7 R 6 R 5 R 4 R 3 R 2 R 1 3 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 4 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 - - - - - - - - - - - - - - - - 32767 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes: Divide ratios less than 3 are prohibited. Data Sheet - Rev 2.1 12/2003 11 ACD2202 Main Divider Programming The main divider register for each synthesizer consists of seven A counter bits, eleven B counter bits, two program mode bits and the two register select bits, as shown in Table 10. The main divider divide ratio, N, is determined by the values in the A and B counters. The eleven B Counter bits and allowed values are shown in Table 11, and the seven A Counter bits and allowed values are shown in 21 20 19 18 17 Program Mode C 2 Pulse Swallow Function The VCO output frequency for the local oscillator is computed using the following equation; the variables are defined in Table 13: fVCO = N x fOSC/R, where N = [(P x B) + A] Table 10: Main Divider Registers MSB 22 Table 12. Note that there are some limitations on the ranges of the values for each counter. C 1 16 15 14 13 12 11 10 9 LSB 8 7 B Counter B 11 B 10 B 9 B 8 B 7 B 6 6 5 4 3 A Counter B 5 B 4 B 3 B 2 B 1 A 7 A 6 A 5 A 4 A 3 2 1 Select A 2 A 1 S 2 S 1 Table 11: Main Divider B Counter Bits VALUE OF B COUNTER B 11 B 10 B 9 B 8 B 7 B 6 B 5 B 4 B 3 B 2 B 1 3 0 0 0 0 0 0 0 0 0 1 1 4 0 0 0 0 0 0 0 0 1 0 0 - - - - - - - - - - - - 2047 1 1 1 1 1 1 1 1 1 1 1 Notes: B > A, Divide ratios less than 3 are prohibited. Table 13: Variable Definitions Table 12: Main Divider A Counter Bits VALUE OF A COUNTER A 7 A 6 A 5 A 4 A 3 A 2 A 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 - - - - - - 127 1 1 1 1 1 Notes: B > A, A < P 12 VAR DEFINITION fVCO Desired output frequency of external voltage controlled oscillator (VCO) 1 B Divide ratio of B counter (3 to 2047) - - A Divide ratio of A counter (0 < A < P, A < B) 1 1 fOSC Frequency of external reference crystal or oscillator R Divide ratio of R counter (3 to 32767) P Preset modulus of prescalar (P = 64) Data Sheet - Rev 2.1 12/2003 ACD2202 Programmable Modes Each register contains bits set aside for programming different modes of operation in the synthesizers. Currently, the only programmable mode is the polarity of the phase detector in each of the synthesizers. Bit D1 in each reference divider register controls this feature. Bits D2 through D5 in the reference divider registers and bits C1 and C2 in the main divider registers are reserved for future use, and have no current function. They can be set either high or low without affecting synthesizer performance. Setting Phase Detector Polarity Table 14 shows how bit D1 of each reference divider register controls the polarity of the phase detector associated with each PLL. The correct setting is determined by using Table 15 and Figure 21. Figure 21: VCO Characteristics Table 14: Phase Detector Polarity Bit S 2 S 1 D 1 0 0 PLL2 Phase Detector Polarity 1 0 PLL1 Phase Detector Polarity (1) Table 15: Phase Detector Polarity Selection D 1 PHASE DETECTOR POLARITY VC O CHARACTERISTICS (SEE FIGURE 12) 0 Negative curve (2) 1 Positive curve (1) VCO OUTPUT FREQUENCY (2) VCO INPUT VOLTAGE Synthesizer Programming Example The following example for programming the two synthesizers in the ACD2202 details the calculations used to determine the required value of each bit in all four registers: Requirements Desired CATV input channel: "HHH" - 499.25 MHz picture carrier (501 MHz digital channel center frequency) (Second) IF picture carrier output frequency: 45.75 MHz (44 MHz digital channel center frequency) First IF frequency: 1087.75 MHz Phase detector comparison frequency for down converter (also tuning increment): 62.5 KHz Phase detector comparison frequency for up converter: 250 KHz Crystal reference oscillator frequency: 4 MHz Calculation of Reference Divider Values The value for each reference divider is calculated by dividing the reference oscillator frequency by the desired phase detector comparison frequency: R = fOSC / fPD For the down converter, the 4 MHz crystal oscillator frequency and the 62.5 KHz phase detector comparison frequency are used to yield RPLL2 = 4 MHz / 62.5 KHz = 64, and so the bit values for the down converter R counter are RPLL2 = 000000001000000. Data Sheet - Rev 2.1 12/2003 13 ACD2202 For the up converter, the 4 MHz crystal oscillator frequency and the 250 KHz phase detector comparison frequency are used to yield RPLL1 = 4 MHz / 250 KHz = 16, and so the bit values for the up converter R counter are RPLL1 = 000000000010000. Calculation of Main Divider Values The values for the A and B counters are determined by the desired VCO output frequency for the local oscillator and the phase detector comparison frequency: N = fVCO / f PD B = trunc(N / P) A = N - (B x P) The down converter local oscillator frequency will be 1087.75 MHz - 45.75 MHz = 1042 MHz in this example. The main divider ratio for the down converter, then, is NPLL2 = 1042 MHz / 62.5 KHz = 16672. Since P = 64 in the ACD2202, BPLL2 = trunc(16672 / 64) = 260, and APLL2 = 16672 - (260 x 64) = 32. These results give bit values of BPLL2 = 00100000100 and APLL2 = 0100000 for the B and A counters. The up converter local oscillator frequency will be 499.25 MHz + 1087.75 MHz = 1587 MHz in this example. Therefore, NPLL1 = 1587 MHz / 250 KHz = 6348, BPLL1 = trunc(6348 / 64) = 99, and APLL1 = 6348 - (99 x 64) = 12. These results give bit values of BPLL1 = 00001100011 and APLL1 = 0001100 for the B and A counters. Phase Detector Polarity Assuming the VCO for the up converter has a negative slope, the phase detector polarity for PLL1 should be negative, and D1PLL1 = 1. If the VCO for the down converter has a positive slope, the phase detector polarity for PLL2 should be positive, and D1PLL2 = 0. In summary, for this example, the four register programming words are shown in Tables 16 and 17: Table 16: PLL1 and PLL2 Reference Divider Register Bits for Synthesizer Programming Example MSB 22 21 20 19 18 17 16 15 14 13 Program Mode 12 11 10 9 8 7 6 LSB 5 4 3 Reference Divider R Counter 2 1 Select D 5 D 4 D 3 D 2 D 1 R 15 R 14 R 13 R 12 R 11 R 10 R 9 R 8 R 7 R 6 R 5 R 4 R 3 R 2 R 1 S 2 S 1 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 Table 17: PLL1 and PLL2 Main Divider Register Bits for Synthesizer Programming Example MSB 22 21 20 19 18 Program Mode 14 17 16 15 14 13 12 11 10 9 Main Divider B Counter 8 7 LSB 6 5 4 3 Main Divider A Counter 2 1 Select C 2 C 1 B 11 B 10 B 9 B 8 B 7 B 6 B 5 B 4 B 3 B 2 B 1 A 7 A 6 A 5 A 4 A 3 A 2 A 1 S 2 S 1 0 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 1 1 Data Sheet - Rev 2.1 12/2003 ACD2202 APPLICATION INFORMATION VSYN VSYN 20 k pins 17,18 pins 16,19 AV~ -1000 VSS VSS VSYN pin 13 pin 1 200 pin 2 VSS VSYN 300 k 5 k pin 14 pin 4 5 k GND GND VSS VSUP pin 27 10 pin 24 pin 5 5 pF 15 5 GND pin 28 5 pF 5 GND 10 pF OSCGND Figure 22: Equivalent Circuits Data Sheet - Rev 2.1 12/2003 15 ACD2202 Figure 23: PC Board Layout Top View Figure 24: PC Board Layout Mid View RF RF AFC Out ACD2202 4M Hz Xtal J1 1 Figure 25: PC Board Layout Bottom View Figure 26 Evaluation Fixture Table 18: J1 Header Pinout Table 19: Fixture Pinout LO In FUNCTION PIN FU N C TION 1 Clock RF D ownconverter RF Input 2 Data RF D ownconverter RF Input 3 Ground IF IF Output (Si ngle Ended) 4 Enable AFC Out To Upconverter Osci llator Tuni ng C i rcui t 5 +5 V DC LO In Synthesi zer RFU LO Input 6 +30 V DC PIN 16 IF Balun Data Sheet - Rev 2.1 12/2003 Data Sheet - Rev 2.1 12/2003 1 2 3 4 5 6 J1 C4 +30V C5 R5 C6 R2 +5V C7 R6 R3 C8 X1 R7 R4 L1 D1 RF RF R1 C1 C3 C2 +5V 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C12 REFOUT REFIN CLK DATA EN VSS VSS OSCGND OSCGND TCKT ISET GND RFIN- RFIN+ R8 C11 ACD2202 VSUP C10 VSYN RFU CPU CPD RFD VSS VSS GND GND OSC OUT L2 27 28 C9 15 16 17 18 19 20 21 22 23 24 25 GND 26 VIF + IFOUT- VIF + IFOUT+ C24 L3 C21 DT1 C13 R9 C20 IF C14 R10 R12 C17 C22 R11 C16 C23 C15 Q1 LOIN AFCOUT +5V R13 C18 C19 +30V ACD2202 Figure 27: Evaluation Fixture Schematic 17 ACD2202 Table 20: Evaluation Fixture Parts List ITEM # VALUE SIZE DESCRIPTION PART # QTY VENDOR C 1, C 2, C 20 100pF 0603 Chip-capacitor GRM39COG101J50V 3 Murata C3 9pF 0603 Chip-capacitor GRM39COG090C50V 1 Murata C 7, C 8 30pF 0603 Chip-capacitor GRM39COG300J50V 2 Murata C 12 220uF PCE2040CT-ND 1 DIGI-KEY 10V VA Capacitor Series C9, C11, C 14, C 21, C 22 .1uF 0603 Chip-capacitor GRM39Y5V104Z16V 5 Murata C 10, C 23 1000pF 0603 Chip-capacitor GRM39X7R102K50V 2 Murata C 15, C 17 4700pF 0603 Chip-capacitor GRM39X7R472K25V 2 Murata C 16 1uF 0603 Radial-lead Chip-capacitor RPE113-X7R-105-K-050 1 Murata C 18 .01uF 0603 Chip-capacitor GRM39X7R103K25V 1 Murata C 19 10uF 35 V TANT TE Series Cap. PCS6106CT-ND 1 DIGI-KEY C 24 15pF 0603 Chip-capacitor GRM39COG150J50V 1 Murata C 13 5600pF 0603 Chip-capacitor GRM39X7R562K50V 1 Murata 33pF 0603 Chip-capacitor GRM39COG330J50V 3 Murata R8 51 0603 Chip Resistor ERJ-3GSYJ510 1 Panasonic R5 10K 0603 Chip Resistor ERJ-3GSYJ103 1 Panasonic R2, R3, R4 2K 0603 Chip Resistor ERJ-3GSYJ202 3 Panasonic R12 1K 0603 Chip Resistor ERJ-3GSYJ102 1 Panasonic R11 2.7K 0603 Chip Resistor ERJ-3GSYJ272 1 Panasonic R7 3K 0603 Chip Resistor ERJ-3GSYJ302 1 Panasonic R13 22K 0603 Chip Resistor ERJ-3GSYJ223 1 Panasonic R10 8.2K 0603 Chip Resistor ERJ-3GSYJ822 1 Panasonic R1 10 0603 Chip Resistor ERJ-3GSYJ100 1 Panasonic C 4, C 5, C6 18 Data Sheet - Rev 2.1 12/2003 ACD2202 Table 20: Evaluation Fixture Parts List continued ITEM # VALUE SIZE DESCRIPTION PART # QTY VENDOR R6, R9 0 0603 Chip Resistor ZC0603 2 RCD L1 5.6nH 0805 Inductor 0805CS-050X-BC 1 Coilcraft L2 68nH 0805 Inductor 0805CS-680X-BC 1 Coilcraft L3 270nH 0805 Inductor 0805CS-271X-BC 1 Coilcraft D1 1S V 245 Varactor diode 1SV245 1 Toshiba DT1 4:1 Transformer ETC4-1-2 1 M/A-COM, Inc. North America Q1 30V SMD Transistor NPN Darl. FMMTA13CT-ND 1 DIGI-KEY X1 4MHZ Crystal SE2618CT-ND 1 DIGI-KEY SOT-23 Data Sheet - Rev 2.1 12/2003 19 ACD2202 PACKAGE OUTLINE Figure 28: S8 Package Outline - 28 Pin SSOP 20 Data Sheet - Rev 2.1 12/2003 ACD2202 NOTES Data Sheet - Rev 2.1 12/2003 21 ACD2202 NOTES 22 Data Sheet - Rev 2.1 12/2003 ACD2202 NOTES Data Sheet - Rev 2.1 12/2003 23 ACD2202 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION A C D 2202S 8P 1 -40C to +85C 28 Pin SSOP Tape & Reel, 3500 pieces per reel A C D 2202S 8P 0 -40C to +85C 28 Pin SSOP Tubes, 50 pieces per tube COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 24 Data Sheet - Rev 2.1 12/2003