3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
Solder Tail
• End-to-endstackable
• Selectloadcapability
• Monoblockable
• ShoulderPin
Press Fit
• End-to-endstackable
• Earlymatelatebreakforhotswapping(press-tEMLB
adjustedbyapplicationtooling)
• Selectloadcapability
• Monoblockable
• Push-onshoulderpin
• Optionalfeed-throughtailforrearplug-upmidplane
applications
• AcceptsUniversalTooling
• RoHSCompliant.SeetheRegulatoryInformation
Appendix(RIA)inthe“RoHScompliance”sectionof
www.3M.com/Interconnectsforcomplianceinformation
(RIAE1&C1apply)
Date Modied: September 9, 2009 TS-1120-C
Sheet 1 of 4
Physical
Insulation:
Material: High Temp LCP
Flammability: UL 94V-0
Color: Beige
Color:
Material: Phosphor Bronze
Plating:
Underplating: 50 μ” [1.27 μm] Nickel
Wiping Area: See Ordering Information
Solder Tails: See Ordering Information
Electrical
Current Rating: Signal: 1.5 A - All contacts simultaneously
Insulation Resistance: 103 MΩ
Withstanding Voltage: 1,000 V
AC
Environmental
Temperature Rating: -55°C to +125°C
Process Temperature Rating: 260°C (Profile per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
ULFileNo.:E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-C
Sheet 2 of 4
Ordering Information
MP2 - HXXX - XXXX - S - XXXXX
SOLDER TAIL
PRODUCT
POSITION X
POSITION 2
FOR SPECIAL MONOBLOCKS
AND PIN ARRANGEMENTS
CONTACT 3M SALES
REPRESENTATIVE
POSITION 1
PRESS-FIT
PRODUCT
REAR
PLUG-UP
5 ROW PRODUCT PRESS-FIT
PRODUCT
ROW
C D E A
B
4 ROW PRODUCT
6.00
.236
"A"
15.80
.622
11.50
.453
1.40
.055
2.00
.079
17.80
.701
13.52
.532
17.00
.669
3.50
.138
MATING LENGTH
"B" TAIL LENGTH
"C"
2.00
.079
12.00
.472
14.00
.551
0 0.0 0.00
mm ±3 ±0.3 ±0.13
mm
[inch]
Tolerance Unless Noted
[ ] Dimensions for Reference Only
H = Header
Pin Count
(See Table 1)
Note:
1. Refer to IEC 61076-4-104 Futurebus+® global standard.
2. “Press Fit” describes a contact tail having a compliant section designed to make a reliable electrical connection with a
plated through-hole (PTH) in a printed circuit board, typically a “back plane.”
Rows
4 = 4 Rows
5 = 5 Rows
Loading Pattern
(See Table 2) Termination Style
P = Press-Fit
S = Solder Tail
Tail Length
(See Table 3)
Plating Options:
(See Table 4)
Shouldered Pins
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-C
Sheet 3 of 4
Table 1 - Connector & Row Lengths
Pin
Count
Dim. “A”
mm [inch]
Dim “C”
mm [inch]
Rows
024 11.95 [0.471] 10.00 [0.394] 4
048 23.95 [0.943] 22.00 [0.866] 4
072 35.95 [1.415] 34.00 [1.339] 4
096 47.95 [1.889] 46.00 [1.811] 4
120 59.95 [2.36] 58.00 [2.283] 4
144 71.95 [2.833] 70.00 [2.756] 4
168 83.95 [3.305] 82.00 [3.228] 4
192 95.95 [3.778] 94.00 [3.701] 4
030 11.95 [0.471] 10.00 [0.394] 5
060 23.95 [0.943] 22.00 [0.866] 5
090 35.95 [1.415] 34.00 [1.339] 5
120 47.95 [1.888] 46.00 [1.811] 5
150 59.95 [2.361] 58.00 [2.283] 5
180 71.95 [2.833] 70.00 [2.756] 5
210 83.95 [3.305] 82.00 [3.228] 5
240 95.95 [3.778] 94.00 [3.701] 5
Table 3 - Tail Length Options
Termination Option No. Dim. “B”
Solder Tail Press-Fit* Tail
1 1 4.60 [0.181]
2 3.53 [0.139]
3 2.72 [0.107]
5 (Contact 3M) 13.60 [0.535]
7 (Contact 3M) 17.00 [0.669]
*Compliant-Pin Tail
Table 4 - Plating Options
Plating
Suffix
Press-Fit
Tails*
Solder
Tails Plating Composition
TG (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.25 μm [10 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TG30 (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR30 (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR40B (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.13 μm [5 μ”] Min. Hard Au Contact Area,
Lubricated
1.02 μm [40 μ”] Min. PdNi Contact Area
0.10 μm [4 μ”] Min. Pd Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
FJ (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.25 μm [10 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
KR (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
RF (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
1.27 μm [50 μ”] Min. Au Contact Area, Lubri-
cated
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
LR (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
PD (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.13 μm [5 μ”] Min. Hard Au Contact Area,
Lubricated
1.02 μm [40 μ”] Min. PdNi Contact Area
0.10 μm [4 μ”] Min. Pd Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
KV (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Dual Contact Areas
0.10 μm [4 μ”] Min. Au Needle Eye
1.27 μm [50 μ”] Min. Ni all over
Table 2 - Mate Length vs. Loading Pattern
Loading Pattern
Code Description Mate length
Row A
Mate length
Row B
Mate length
Row C
Mate length
Row D
Mate length
Row E
(5-Row Prod. Only)
1 All Positions Filled 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
2 All Positions Filled 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
3 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.75 [0.226] 6.50 [0.256] 6.50 [0.256]
4 All Positions Filled 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256]
5 All Positions Filled 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
6 All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
7 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
8 All Positions Filled 6.50 [0.256] 5.00 [0.197] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256]
9 All Positions Filled 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
A All Positions Filled 5.00 [0.197] 5.75 [0.226] 6.50 [0.256] 5.75 [0.226] 5.00 [0.197]
B All Positions Filled 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
C All Positions Filled 5.00 [0.197] 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197]
D All Positions Filled 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226]
E All Positions Filled 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285]
G All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197]
H All Positions Filled 5.00 [0.197] 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 7.25 [0.285]
J All Positions Filled 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315]
K All Positions Filled 5.00 [0.197] 6.50 [0.256] 7.25 [0.285] 6.50 [0.256] 5.00 [0.197]
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-C
Sheet 4 of 4
2.00
.079
Ø
1.50
+.10
-.00
.059
+.004
-.000
UNPLATED
12.0 0
.47 2
2.00
.079
2.00
.079
16.00
.630 M IN
"D " PLATED TH RU HO LE
"C "
0.10
0.10
CENTER HOL E S OP TION AL
FOR 3M PRODUC T
12 .00
.472
12.00
.472
A1
6.00
.236
1 6 . 0 0
. 6 3 0 M I N
" D " P L A T E D T H R U H O L E
0 . 1 0
Ø
Ø
Ø
6.00
.236
2.00
.079
2.00
.079
"D" PLATED THRU HOLE
"C"
14.00
.551
2.00
.079
18.00
.709 MIN
1.50
+.10
-.00
.059
+.004
-.000
UNPLATED
0.10
0.10
A1
CENTER HOLES OPTIONAL
FOR 3M PRODUCT
12.00
.472
12.00
.472
"D " P L A T E D T H R U H O L E
1 8 .0 0
.7 0 9 M IN
0 .1 0
Ø
Ø
Ø
Ø
Table 5 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY
HOLE Finished Dia. mm [in] Cu Thickness mm [in] SnPb Thickness microns [μ”] Drilled Hole Dia. mm [in]
“D” 0.65-0.80 [.0256-.0315] 0.025 [.001] min. 15 [600] max. 0.81-0.86 [.0319-.0339]
Table 6 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY
Hole Finished Dia.
mm [in]
Cu Thickness
mm [in]
Immersion
Matte Sn
Thickness
microns [μ”]
Electrolitic Au
Thickness
microns [μ”]
OSP ENTEK
Thickness
microns [μ”]
Drilled Hole Dia.
mm [in]
“D” 0.700-0.800
[.0276-.0315]
0.025-0.045
[0.001-0.002]
0.5 - 2.5
[20 - 100]
0.1 - 0.5
[4 - 20]
0.2 - 0.5
[8 - 20]
0.830-0.860 [.0330-.0340] or
0.85mm [ #66] TWIST DRILL
RECOMMENDED 4 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
RECOMMENDED 4 ROW PRESS-FIT
RECOMMENDED 5 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
RECOMMENDED 5 ROW PRESS-FIT
PCB HOLE MOUNTING PATTERN
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217B-E
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects 3M is a trademark of 3M Company.