07514 September 17, 2012 Rev: A
EN2360QI
6A Voltage Mode Synchronous Buck PWM
DC-DC Converter with Integrated Inductor
www.enpirion.com
Description
The EN2360QI is a Power System on a Chip
(PowerSoC) DC-DC converter. It integrates MOSFET
switches, small-signal control circuits, compensation
and an integrated inductor in an advanced 8x11x3mm
QFN module. It offers high efficiency, excellent line
and load regulation over temperature. The EN2360QI
operates over a wide input voltage range and is
specifically designed to meet the precise voltage and
fast transient requirements of high-performance
products. The EN2360QI features frequency
synchronization to an external clock, power OK
output voltage monitor, programmable soft-start along
with thermal and over current protection. The device’s
advanced circuit design, ultra high switching
frequency and proprietary integrated inductor
technology delivers high-quality, ultra compact, non-
isolated DC-DC conversion.
The Enpirion solution significantly helps in system
design and productivity by offering greatly simplified
board design, layout and manufacturing
requirements. In addition, overall system level
reliability is improved given the small number of
components required with the Enpirion solution.
All Enpirion products are RoHS compliant and lead-
free manufacturing environment compatible.
Features
• Integrated Inductor, MOSFETs, Controller
• Wide Input Voltage Range: 4.5V – 14V
• Total Solution Size Estimate: 185mm2
• Frequency Synchronization (External Clock)
• 2% VOUT Accuracy (Over Line/Load/Temperature)
• Output Enable Pin and Power OK signal
• Programmable Soft-Start Time
• Can be Pin Compatible with the EN2340QI (4A)
• Under Voltage Lockout Protection (UVLO)
• Programmable Over Current Protection
• Thermal Shutdown and Short Circuit Protection
• RoHS Compliant, MSL Level 3, 260oC Reflow
Applications
• Space Constrained Applications
• Distributed Power Architectures
• Output Voltage Ripple Sensitive Applications
• Beat Frequency Sensitive Applications
• Servers, Embedded Computing Systems,
LAN/SAN Adapter Cards, RAID Storage Systems,
Industrial Automation, Test and Measurement,
and Telecommunications
Figure 1. Simplified Applications Circuit
(Footprint Optimized) Figure 2. Highest Efficiency in Smallest Solution Size
0
10
20
30
40
50
60
70
80
90
100
00.511.522.533.544.555.56
EFFICIENCY (%)
OUTPUT CURRENT (A)
Efficiency vs. Output Current
VOUT = 3.3V
VOUT = 1.8V
VOUT = 1.2V
CONDITIONS
V
IN
= 12.0V
AVIN = 3.3V
Dual Supply
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 2
Ordering Information
Part Number Package Markings Temp Rating (°C) Package Description
EN2360QI EN2360QI -40 to +85 68-pin (8mm x 11mm x 3mm) QFN T&R
EN2360QI-E EN2360QI QFN Evaluation Board
Packing and Marking Information: http://www.enpirion.com/resource-center-packing-and-marking-information.htm
Pin Assignments (Top View)
Figure 3: Pin Out Diagram (Top View)
NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage.
However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage.
NOTE B: Shaded area highlights exposed metal below the package that is not to be mechanically or electrically
connected to the PCB. Refer to Figure 12 for details.
NOTE C: White ‘dot’ on top left is pin 1 indicator on top of the device package.
Pin Description
I/O Legend: P=Power G=Ground NC=No Connect I=Input O=Output I/O=Input/Output
PIN NAME I/O FUNCTION
1-15,
25-26,
59, 64-
68
NC NC
NO CONNECT – These pins may be internally connected. Do not connect them to each
other or to any other electrical signal. Failure to follow this guideline may result in device
damage.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 3
PIN NAME I/O FUNCTION
16-24 VOUT O
Regulated converter output. Connect these pins to the load and place output capacitor
between these pins and PGND pins 29-31.
27-28,
61-63 NC(SW) NC
NO CONNECT – These pins are internally connected to the common switching node of the
internal MOSFETs. They are not to be electrically connected to any external signal, ground,
or voltage. Failure to follow this guideline may result in damage to the device.
29-34 PGND G
Input/Output power ground. Connect these pins to the ground electrode of the input and
output filter capacitors. See VOUT and PVIN pin descriptions for more details.
35-41 PVIN P
Input power supply. Connect to input power supply. Decouple with input capacitor to
PGND pins 32-34.
42 AVINO O
Internal 3.3V linear regulator output. Connect this pin to AVIN (Pin 51) for applications
where operation from a single input voltage (PVIN) is required. If AVINO is being used,
place a 1µF, X5R, capacitor between AVINO and AGND as close as possible to AVINO.
43 PG I/O Place a 47nF, X5R, capacitor between this pin and BTMP.
44 BTMP I/O See pin 43 description.
45 VDDB O
Internal regulated voltage used for the internal control circuitry. Place a 0.22µF, X5R,
capacitor between this pin and BGND.
46 BGND G See pin 45 description.
47 S_IN I
Digital Input. This pin accepts either an input clock to phase lock the internal switching
frequency or a S_OUT signal from another EN2360QI. Leave this pin floating if not used.
48 S_OUT O Digital Output. PWM signal is output on this pin. Leave this pin floating if not used.
49 POK O
Power OK is an open drain transistor (pulled up to AVIN or similar voltage) used for power
system state indication. POK is logic high when VOUT is within -10% of VOUT nominal.
Leave this pin floating if not used.
50 ENABLE I
Input Enable. Applying a logic high to this pin enables the output and initiates a soft-start.
Applying a logic Low disables the output. Do not leave floating.
51 AVIN P
3.3V Input power supply for the controller. Place a 0.1µF, X5R, capacitor between AVIN
and AGND.
52, 53 AGND G Analog Ground. This is the ground return for the controller. All AGND pins need to be
connected to a quiet ground.
54 VFB I/O
External Feedback Input. The feedback loop is closed through this pin. A voltage divider at
VOUT is used to set the output voltage. The mid-point of the divider is connected to VFB. A
phase lead capacitor from this pin to VOUT is also required to stabilize the loop.
55 EAIN O
Optional Error Amplifier Input. Allows for customization of the control loop for performance
optimization. Leave this pin floating if not used.
56 SS I/O
Soft-start node. The soft-start capacitor is connected between this pin and AGND. The
value of this capacitor determines the startup time. See Soft-Start Operation in the
Functional Description section for details.
57 RCLX I/O
Programmable over-current protection. Placement of a resistor on this pin will adjust the
over-current protection threshold. See Table 2 for the recommended RCLX Value to set
OCP at the nominal value specified in the Electrical Characteristics table. No current limit
protection when this pin is left floating.
58 FADJ I/O
Adding a resistor (RFS) to this pin will adjust the switching frequency of the EN2360QI. See
Table 1 for suggested resistor values on RFS for various PVIN/VOUT combinations to
maximize efficiency. Do not leave this pin floating.
60 CGND Test pin. For Enpirion Internal Use Only. Connect to GND plane at all times.
69 PGND
Not a perimeter pin. Device thermal pad to be connected to the system GND plane for heat-
sinking purposes.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 4
Absolute Maximum Rati ngs
CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating
conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute
maximum rated conditions for extended periods may affect device reliability.
PARAMETER SYMBOL MIN MAX UNITS
Voltages on – PVIN, VOUT VIN -0.5 15 V
Pin Voltages – AVINO, AVIN, ENABLE, POK, S_IN, S_OUT, M/S 2.5 6.0 V
Pin Voltages – VFB, SS, EAIN, RCLX, FADJ -0.5 2.75 V
PVIN Slew Rate 0.3 3 V/ms
Storage Temperature Range TSTG -65 150 °C
Maximum Operating Junction Temperature TJ-ABS Max 150 °C
Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A 260 °C
ESD Rating - all pins (based on Human Body Model) 2000 V
ESD Rating (based on CDM) 500 V
Recommended Operating Conditions
PARAMETER SYMBOL MIN MAX UNITS
PVIN: Input Voltage Range PVIN 4.5 14.0 V
AVIN: Controller Supply Voltage AVIN 2.5 5.5 V
Output Voltage Range (Note 1) VOUT 0.6 5.0 V
Output Current IOUT 6.0 A
Operating Junction Temperature TJ-OP - 40 125 °C
Operating Ambient Temperature TAMB - 40 85 °C
Thermal Characteristics
PARAMETER SYMBOL TYP UNITS
Thermal Resistance: Junction to Ambient (0 LFM) (Note 2) θJA 16 °C/W
Thermal Resistance: Junction to Case (0 LFM) θJC 2 °C/W
Thermal Shutdown TSD 160 °C
Thermal Shutdown Hysteresis TSDH 35 °C
Note 1: RCLX resistor value may need to be raised for VOUT > VIN – 2.5V to increase current limit threshold. Contact
techsupport@enpirion.com for details.
Note 2: Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for
high thermal conductivity boards.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 5
Electrical Characteristics
NOTE: VIN=12V, Minimum and Maximum values are over operating ambient temperature range unless otherwise noted.
Typical values are at TA = 25°C.
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
Operating Input Voltage PVIN 4.5 14.0 V
Controller Input Voltage AVIN 2.5 5.5 V
PVIN Under Voltage
Lock-out UVLOPVIN Voltage above which UVLO is not
asserted 2 V
AVIN Under Voltage
Lock-out rising AVINUVLOR Voltage above which UVLO is not
asserted 2.3 V
AVIN Under Voltage
Lock-out falling AVINOVLOF Voltage below which UVLO is
asserted 2.1 V
AVIN Pin Input Current IAVIN 9 mA
Internal Linear Regulator
Output Voltage AVINO 3.3 V
Shut-Down Supply
Current
IPVINS PVIN=12V, AVIN=3.3, ENABLE=0V 300 μA
IAVINS PVIN=12V, AVIN=3.3, ENABLE=0V 50 μA
Feedback Pin Voltage VFB
Feedback node voltage at:
VIN = 12V, ILOAD = 0, TA = 25°C
0.594
0.60
0.606 V
Feedback Pin Voltage VFB
Feedback node voltage at:
4.5V VIN 14V
0A ILOAD 6A, TA = -40 to 85°C
0.588
0.60
0.612 V
Feedback pin Input
Leakage Current IFB VFB pin input leakage current
(Note 3) -5 5 nA
VOUT Rise Time tRISE CSS = 47nF
(Note 3, Note 4 and Note 5) 1.96 2.8 3.64 ms
Soft Start Capacitor
Range CSS_RANGE 47 nF
Maximum Continuous
Output Current IOUT_CONT 0 6 A
Over Current Trip Level IOCP Reference Table 2 9 A
ENABLE Logic High VENABLE_HIGH 4.5V VIN 14V; 1.8 AVIN V
ENABLE Logic Low VENABLE_LOW 4.5V VIN 14V; 0 0.6 V
ENABLE Lockout Time TENLOCKOUT 8 ms
ENABLE pin Input
Current IENABLE 180kΩ pull down (Note 3) 4 μA
Switching Frequency FSW RFADJ =3k 1.0 MHz
External SYNC Clock
Frequency Lock Range FPLL_LOCK Range of SYNC clock frequency 0.8 1.6 MHz
S_IN Threshold – Low VS_IN_LO S_IN Clock Logic Low Level (Note 3) 0.8 V
S_IN Threshold – High VS_IN_HI S_IN Clock Logic High Level (Note 3) 1.8 2.5 V
S_OUT Threshold – Low VS_OUT_LO S_OUT Clock Logic Low Level
(Note 3) 0.8 V
S_OUT Threshold –
High VS_OUT_HI S_OUT Clock Logic High Level
(Note 3) 1.8 2.5 V
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 6
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS
POK Lower Threshold POKLT Percentage of Nominal Output
Voltage for POK to be Low 90 %
POK Output low Voltage VPOKL With 4mA Current Sink into POK 0.4 V
POK Output Hi Voltage VPOKH PVIN range: 4.5V VIN 14V AVIN V
POK pin VOH leakage
current IPOKL POK High (Note 3) 1 µA
M/S Pin Logic Low VT-LOW Tie Pin to GND 0.8V V
M/S Pin Logic High VT-HIGH Pull up to AVIN Through an External
Resistor REXT 1.8V V
M/S Pin Input Current IM/S VIN = 5.0V, REXT = 24.9kΩ 100 μA
Note 3: Parameter not production tested but is guaranteed by design.
Note 4: Rise time calculation begins when AVIN > VUVLO and ENABLE = HIGH.
Note 5: VOUT Rise Time Accuracy does not include soft-start capacitor tolerance.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 7
Typical Performance Curves
0
10
20
30
40
50
60
70
80
90
100
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
EFFICIENCY (%)
OUTPUT CURRENT (A)
Efficiency vs. Output Current
VOUT = 3.3V
VOUT = 1.8V
VOUT = 1.2V
CONDITIONS
VIN = 10.0V
AVIN = 3.3V
Dual Supply
0
10
20
30
40
50
60
70
80
90
100
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
EFFICIENCY (%)
OUTPUT CURRENT (A)
Efficiency vs. Output Current
VOUT = 3.3V
VOUT = 1.8V
VOUT = 1.2V
CONDITIONS
V
IN
= 12.0V
AVIN = 3.3V
Dual Supply
0.0
1.0
2.0
3.0
4.0
5.0
6.0
75 76 77 78 79 80 81 82 83 84 85
MAXIMUM OUTPUT CURRENT (A)
AMBIENT TEMPERATURE ( C)
Output Current De-rating
VOUT = 3.3V
CONDITIONS
V
IN
= 12V
T
JMAX
= 125 C
JA
= 16 C/W
8x11x3mm QFN
No Air Flow
0.0
1.0
2.0
3.0
4.0
5.0
6.0
75 76 77 78 79 80 81 82 83 84 85
MAXIMUM OUTPUT CURRENT (A)
AMBIENT TEMPERATURE ( C)
Output Current De-rating
VOUT = 3.3V
CONDITIONS
V
IN
= 10V
T
JMAX
= 125 C
JA
= 16 C/W
8x11x3mm QFN
No Air Flow
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
75 76 77 78 79 80 81 82 83 84 85
MAXIMUM OUTPUT CURRENT (A)
AMBIENT TEMPERATURE ( C)
No De-rating with Air Flow
VOUT = 3.3V
CONDITIONS
V
IN
= 12V
T
JMAX
= 125 C
JA
= 13 C/W
8x11x3mm QFN
Air Flow (200fpm)
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
75 76 77 78 79 80 81 82 83 84 85
MAXIMUM OUTPUT CURRENT (A)
AMBIENT TEMPERATURE ( C)
No De-rating with Air Flow
VOUT = 3.3V
CONDITIONS
V
IN
= 10V
T
JMAX
= 125 C
JA
= 13 C/W
8x11x3mm QFN
Air Flow (200fpm)
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 8
Typical Performance Curves
0.995
0.996
0.997
0.998
0.999
1.000
1.001
1.002
1.003
1.004
1.005
00.511.522.533.544.555.56
OUTPUT VOLTAGE (V)
OUTPUT CURRENT (A)
Output Voltage vs. Output Current
VIN = 8V
VIN = 10V
VIN = 12V
CONDITIONS
V
OUT_NOM
= 1.0V
1.195
1.196
1.197
1.198
1.199
1.200
1.201
1.202
1.203
1.204
1.205
00.511.522.533.544.555.56
OUTPUT VOLTAGE (V)
OUTPUT CURRENT (A)
Output Voltage vs. Output Current
VIN = 8V
VIN = 10V
VIN = 12V
CONDITIONS
V
OUT_NOM
= 1.2V
1.795
1.796
1.797
1.798
1.799
1.800
1.801
1.802
1.803
1.804
1.805
00.511.522.533.544.555.56
OUTPUT VOLTAGE (V)
OUTPUT CURRENT (A)
Output Voltage vs. Output Current
VIN = 8V
VIN = 10V
VIN = 12V
CONDITIONS
V
OUT_NOM
= 1.8V
2.495
2.496
2.497
2.498
2.499
2.500
2.501
2.502
2.503
2.504
2.505
00.511.522.533.544.555.56
OUTPUT VOLTAGE (V)
OUTPUT CURRENT (A)
Output Voltage vs. Output Current
VIN = 8V
VIN = 10V
VIN = 12V
CONDITIONS
V
OUT_NOM
= 2.5V
1.196
1.197
1.198
1.199
1.200
1.201
1.202
1.203
1.204
-40 -15 10 35 60 85
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE ( C)
Output Voltage vs. Temperature
LOAD = 0A
LOAD = 1A
LOAD = 2A
LOAD = 4A
LOAD = 6A
CONDITIONS
V
IN
= 8V
V
OUT_NOM
= 1.2V
1.196
1.197
1.198
1.199
1.200
1.201
1.202
1.203
1.204
-40 -15 10 35 60 85
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE ( C)
Output Voltage vs. Temperature
LOAD = 0A
LOAD = 1A
LOAD = 2A
LOAD = 4A
LOAD = 6A
CONDITIONS
V
IN
= 10V
V
OUT_NOM
= 1.2V
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 9
Typical Performance Curves
1.196
1.197
1.198
1.199
1.200
1.201
1.202
1.203
1.204
-40 -15 10 35 60 85
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE ( C)
Output Voltage vs. Temperature
LOAD = 0A
LOAD = 1A
LOAD = 2A
LOAD = 4A
LOAD = 6A
CONDITIONS
V
IN
= 12V
V
OUT_NOM
= 1.2V
1.196
1.197
1.198
1.199
1.200
1.201
1.202
1.203
1.204
-40 -15 10 35 60 85
OUTPUT VOLTAGE (V)
AMBIENT TEMPERATURE ( C)
Output Voltage vs. Temperature
LOAD = 0A
LOAD = 1A
LOAD = 2A
LOAD = 4A
LOAD = 6A
CONDITIONS
V
IN
= 14V
V
OUT_NOM
= 1.2V
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 10
Typical Performance Characteristics
ENABLE
Enable Startup/Shutdown Waveform (0A)
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 0A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
VOUT
POK
LOAD
ENABLE
Enable Startup/Shutdown Waveform (2A)
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 2A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
VOUT
POK
LOAD
ENABLE
Enable Startup/Shutdown Waveform (4A)
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 4A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
VOUT
POK
LOAD
ENABLE
Enable Startup/Shutdown Waveform (6A)
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 6A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
VOUT
POK
LOAD
PVIN
Power Up Waveform (0A)
VOUT
POK
LOAD
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 0A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
PVIN
Power Up Waveform (6A)
VOUT
POK
LOAD
CONDITIONS
VIN = 12V, VOUT = 3.3V, Load = 6A, Css = 47nF
CIN = 22µF(1206), COUT = 2x47µF(1206)+100µF(1206)
07514 September 17, 2012 Rev: A
EN2360QI
www.enpirion.com
Typical Performance Characteristics
VOUT = 1V
(AC Coupled)
Output Ripple at 20MHz Bandwidth
CONDITIONS
VIN = 12V, CIN = 22µF (1206), COUT = 2x47µF + 100µF (1206)
VOUT = 1.8V
(AC Coupled)
VOUT = 3.3V
(AC Coupled)
LOAD = 0A
20mV / DIV
VOUT = 1V
(AC Coupled)
Output Ripple at 20MHz Bandwidth
CONDITIONS
VIN = 12V, CIN = 22µF (1206), COUT = 2x47µF + 100µF (1206)
VOUT = 1.8V
(AC Coupled)
VOUT = 3.3V
(AC Coupled)
LOAD = 6A
20mV / DIV
VOUT = 1V
(AC Coupled)
Output Ripple at 500MHz Bandwidth
CONDITIONS
VIN = 12V, CIN = 22µF (1206), COUT = 2x47µF + 100µF (1206)
VOUT = 1.8V
(AC Coupled)
VOUT = 3.3V
(AC Coupled)
LOAD = 0A
20mV / DIV
VOUT = 1V
(AC Coupled)
Output Ripple at 500MHz Bandwidth
CONDITIONS
VIN = 12V, CIN = 22µF (1206), COUT = 2x47µF + 100µF (1206)
VOUT = 1.8V
(AC Coupled)
VOUT = 3.3V
(AC Coupled)
LOAD = 6A
20mV / DIV
VOUT
(AC Coupled)
Load Transient from 0 to 3A (V
OUT
=1V)
CONDITIONS
VIN = 12V, VOUT = 1.0V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 6A (V
OUT
=1V)
CONDITIONS
VIN = 12V, VOUT = 1.0V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
07514 September 17, 2012 Rev: A
EN2360QI
www.enpirion.com
Typical Performance Characteristics
VOUT
(AC Coupled)
Load Transient from 0 to 3A (V
OUT
=1.2V)
CONDITIONS
VIN = 12V, VOUT = 1.2V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 6A (V
OUT
=1.2V)
CONDITIONS
VIN = 12V, VOUT = 1.2V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 3A (V
OUT
=1.8V)
CONDITIONS
VIN = 12V, VOUT = 1.8V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 6A (V
OUT
=1.8V)
CONDITIONS
VIN = 12V, VOUT = 1.8V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 3A (V
OUT
=3.3V)
CONDITIONS
VIN = 12V, VOUT = 3.3V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
VOUT
(AC Coupled)
Load Transient from 0 to 6A (V
OUT
=3.3V)
CONDITIONS
VIN = 12V, VOUT = 3.3V
CIN = 22µF (1206)
COUT = 2x47µF (1206) + 100µF (1206)
Using Best Performance Configuration
LOAD
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 13
Functional Block Diagram
Soft Start
Power
Good
Logic
Band Gap
Reference
Voltage Reference Generator
Compensation
Network
Thermal Limit
UVLO
Current Limit
Gate Drive
PLL/Sawtooth
Generator
FADJ
ENABLE
SS
AGND
POK
AVIN
VFB
PGND
VOUT
NC(SW)
PVIN
S_IN
Error
Amp
PWM
Comp
(+)
(-)
(-)
(+)
Digital I/O
S_OUT
To PLL
Linear
Regulator AVINO
300k
180k
Compensation
Network
EAIN
PGBTMP
BGND
VDDB
10k
Figure 4: Functional Block Diagram
Functional Description
Synchronous Buck Converter
The EN2360QI is a highly integrated synchronous,
buck converter with integrated controller, power
MOSFET switches and integrated inductor. The
nominal input voltage (PVIN) range is 4.5V to 14V
and can support up to 6A of continuous output
current. The output voltage is programmed using
an external resistor divider network. The control
loop utilizes a Type IV Voltage-Mode compensation
network and maximizes on a low-noise PWM
topology. Much of the compensation circuitry is
internal to the device. However, a phase lead
capacitor is required along with the output voltage
feedback resistor divider to complete the Type IV
compensation network.. The high switching
frequency of the EN2360QI enables the use of
small size input and output capacitors, as well as a
wide loop bandwidth within a small foot print.
Protection Features:
The power supply has the following protection
features:
• Programmable Over-Current Protection
• Thermal Shutdown with Hysteresis.
• Under-Voltage Lockout Protection
Additional Features:
• Switching Frequency Synchronization.
• Programmable Soft-Start
• Power OK Output Monitoring
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 14
Power Power Up Sequence
The EN2360QI is designed to be powered by either
a single input supply (PVIN) or two separate
supplies: one for PVIN and the other for AVIN.
Single Input Supply Application (PVIN):
VOUT
VIN
22 F
1206
VOUT
ENABLE
AGND
PVIN
AVIN
PGND PGND
47nF
VFB
RA
RB
RCA
CA
RCLX
2x
F
0805
AVINO
PG BTMP
EN2360QI
SS
VDDB BGND
FADJ
RVB
4.75k
F
0.22µF47nF
RFS RCLX
F
Figure 5. Single Supply Applications Circuit
The EN2360QI has an internal linear regulator that
converts PVIN to 3.3V. The output of the linear
regulator is provided on the AVINO pin once the
device is enabled. AVINO should be connected to
AVIN on the EN2360QI. In this application, the
following external components are required: Place
a 1µF, X5R/X7R, capacitor between AVINO and
AGND as close as possible to AVINO. Place a
0.1µF, X5R/X7R, capacitor between AVIN and
AGND as close as possible to AVIN. In addition,
place a resistor (RVB) between VDDB and AVIN, as
shown in Figure 5. Enpirion recommends
RVB=4.75k. In this application, ENABLE cannot be
asserted before PVIN. If no external enable signal
is used, tying ENABLE to AVIN meets this
requirement.
Dual Input Supply Application (PVIN and AVIN):
Figure 6: Dual Input Supply Application Circuit
In this application, place a 0.1µF, X7R, capacitor
between AVIN and AGND as close as possible to
AVIN. Refer to Figure 6 for a recommended
schematic for a dual input supply application.
For dual input supply applications, the sequencing
of the two input supplies, PVIN and AVIN, is very
important. There are two common acceptable turn-
on sequences for the device. AVIN can always
come up before PVIN. If PVIN comes up before
AVIN, then ENABLE should be toggled last, after
AVIN is asserted. During turn-off, the ENABLE
should be toggled low before AVIN or PVIN is
disabled.
Enable Operation
The ENABLE pin provides a means to enable
normal operation or to shut down the device. A
logic high will enable the converter into normal
operation. When the ENABLE pin is asserted (high)
the device will undergo a normal soft-start, allowing
the output voltage to rise monotonically into
regulation. A logic low will disable the converter and
the device will power down in a controlled manner.
The ENABLE signal has to be low for at least the
ENABLE Lockout Time (8ms) in order for the
device to be re-enabled.
Pre-Bias Precaution
The EN2360QI is not designed to be turned on into
a pre-biased output voltage. Be sure the output
capacitors are not charged or the output of the
EN2360QI is not pre-biased when the EN2360QI is
first enabled.
Frequency Synchronization
The switching frequency of the EN2360QI can be
phase-locked to an external clock source to move
unwanted beat frequencies out of band. The
internal switching clock of the EN2360QI can be
phase locked to a clock signal applied to the S_IN
pin. An activity detector recognizes the presence of
an external clock signal and automatically phase-
locks the internal oscillator to this external clock.
Phase-lock will occur as long as the input clock
frequency is in the range of 0.8MHz to 1.6MHz.
When no clock is present, the device reverts to the
free running frequency of the internal oscillator.
Adding a resistor (RFS) to the FADJ pin will adjust
the switching frequency. If a 3k resistor is placed
on FADJ the nominal switching frequency of the
EN2360QI is 1MHz. Figure 7 shows the typical RFS
resistor value versus switching frequency.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 15
Figure 7. RFS versus Switching Frequency
The efficiency performance of the EN2360QI for
various VOUTs can be optimized by adjusting the
switching frequency. Table 1 shows recommended
RFS values for various VOUTs in order to optimize
performance of the EN2360QI.
PVIN VOUT RFS
12V
1.0V 3k
1.2V 3.3k
1.8V 4.87k
2.5V 10k
3.3V 15k
5.0V 22k
Table 1: Recommended RFS Values
Spread Spectrum Mode
The external clock frequency may be swept
between 0.8MHz and 1.6MHz at repetition rates of
up to 10 kHz in order to reduce EMI frequency
components.
Soft-Start Operation
Soft start is a means to ramp the output voltage
gradually upon start-up. The output voltage rise
time is controlled by the choice of soft-start
capacitor, which is placed between the SS pin (pin
56) and the AGND pin (pin 52).
Rise Time (ms): TR ≈ Css [nF] x 0.06
During start-up of the converter, the reference
voltage to the error amplifier is linearly increased to
its final level by an internal current source of
approximately 10µA. Typical soft-start rise time is
~2.8ms with SS capacitor value of 47nF. The rise
time is measured from when VIN > VUVLOR and
ENABLE pin voltage crosses its logic high
threshold to when VOUT reaches its programmed
value.
POK Operation
The POK signal is an open drain signal (requires a
pull up resistor to AVIN or similar voltage) from the
converter indicating the output voltage is within the
specified range. Typically, a 100k or lower
resistance is used as the pull-up resistor. The POK
signal will be logic high (AVIN) when the output
voltage is above 90% of the programmed voltage
level. If the output voltage is below this point, the
POK signal will be a logic low. The POK signal can
be used to sequence down-stream converters by
tying to their enable pins.
Over-Current Protection (OCP)
The current limit function is achieved by sensing
the current flowing through a sense PFET. When
the sensed current exceeds the current limit, both
power FETs are turned off for the rest of the
switching cycle. If the over-current condition is
removed, the over-current protection circuit will re-
enable PWM operation. If the over-current condition
persists, the circuit will continue to protect the load.
The OCP trip point is nominally set as specified in
the Electrical Characteristics table. In the event the
OCP circuit trips consistently in normal operation,
the device enters a hiccup mode. While in hiccup
mode, the device is disabled for a short while and
restarted with a normal soft-start. The hiccup time
is approximately 32ms. This cycle can continue
indefinitely as long as the over current condition
persists.
The OCP trip point can be programmed to trip at a
lower level via the RCLX pin. The value of the
resistor connected between RCLX and ground will
determine the OCP trip point. Generally, the higher
the RCLX value, the higher the current limit
threshold. Note that if RCLX pin is left open the
output current will be unlimited and the device will
not have current limit protection. Reference Table 2
for a list of recommended resistor values on RCLX
that will set the OCP trip point at the typical value of
9A, also specified in the Electrical Characteristics
table.
VOUT Range RCLX Value
0.6V < VOUT 0.9V 36.5k
0.9V < VOUT 1.2V 38.4k
1.2V < VOUT 2.0V 40.2k
2.0V < VOUT 5.0V 45.3k
Table 2: Recommended RCLX Values vs. VOUT
0.600
0.800
1.000
1.200
1.400
1.600
1.800
0 2 4 6 8 10121416182022
SWITCHING FREQUENCY (MHz)
R
FS
RESISTOR VALUE (k)
Rfs vs. SW Frequency
CONDITIONS
V
IN
= 6V to 12V
V
OUT
= 0.8V to 3.3V
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 16
Thermal Overload Protection
Thermal shutdown circuit will disable device
operation when the junction temperature exceeds
approximately 150ºC. After a thermal shutdown
event, when the junction temperature drops by
approx 20ºC, the converter will re-start with a
normal soft-start.
Input Under-Voltage Lock-Out (UVLO)
Internal circuits ensure that the converter will not
start switching until the input voltage is above the
specified minimum voltage. Hysteresis, input de-
glitch and output leading edge blanking ensures
high noise immunity and prevents false UVLO
triggers.
Application Information
Output Voltage Programming and Loop
Compensation
The EN2360QI uses a Type IV Voltage Mode
compensation network. Type IV Voltage Mode
control is a proprietary Enpirion control scheme that
maximizes control loop bandwidth to deliver
excellent load transient responses and maintain
output regulation with pin point accuracy. For ease
of use, most of this network has been customized
and is integrated within the device package. The
EN2360QI output voltage is programmed using a
simple resistor divider network (RA and RB). The
feedback voltage at VFB is nominally 0.6V. RA is
predetermined based on Table 5 and RB can be
calculated based on Figure 10. The values
recommended for COUT, CA, RCA and REA make up
the external compensation of the EN2360QI. It will
vary with each PVIN and VOUT combination to
optimize on performance. The EN2360QI solution
can be optimized for either smallest size or highest
performance. Please see Table 5 for a list of
recommended RA, CA, RCA, REA and COUT values for
each solution.
Figure 8: VOUT Resistor Divider & Compensation
Components. See Table 5 for details.
Input Capacitor Selection
The EN2360QI requires a 22µF/1206 input
capacitor. Low-cost, low-ESR ceramic capacitors
should be used as input capacitors for this
converter. The dielectric must be X5R or X7R
rated. Y5V or equivalent dielectric formulations
must not be used as these lose too much
capacitance with frequency, temperature and
bias voltage. In some applications, lower value
capacitors are needed in parallel with the larger,
capacitors in order to provide high frequency
decoupling. Table 3 contains a list of
recommended input capacitors.
Recommended Input Capacitors
Description MFG P/N
22µF, 16V,
X5R, 10%,
1206
Murata GRM31CR61C226ME15
22µF, 16V,
X5R, 20%,
1206
Taiyo Yuden EMK316ABJ226ML-T
Table 3: Recommended Input Capacitors
Output Capacitor Selection
As seen from Table 5, the EN2360QI has been
optimized for use with one 100µF/1206 plus two
47µF/1206 output capacitors for best performance.
For the smallest solution size configuration see
Table 5. Low ESR ceramic capacitors are required
with X5R or X7R rated dielectric formulation. Y5V
or equivalent dielectric formulations must not
be used as these lose too much capacitance
with frequency, temperature and bias voltage.
Table 4 contains a list of recommended output
capacitors
Output ripple voltage is determined by the
aggregate output capacitor impedance. Capacitor
impedance, denoted as Z, is comprised of
capacitive reactance, effective series resistance,
ESR, and effective series inductance, ESL
reactance.
Placing output capacitors in parallel reduces the
impedance and will hence result in lower ripple
voltage.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 17
nTotal ZZZZ 1
...
111
21
+++=
Recommended Output Capacitors
Description MFG P/N
47µF, 6.3V, X5R,
20%, 1206 Murata GRM31CR60J476ME19L
47µF, 10V, X5R,
20%, 1206
Taiyo
Yuden LMK316BJ476ML-T
22µF, 10V, X5R,
20%, 0805 Panasonic ECJ-2FB1A226M
47µF, 6.3V, X5R,
20%, 0805
Taiyo
Yuden JMK212BBJ476MG-T
22µF, 10V, X5R,
20%, 0805
Taiyo
Yuden LMK212BJ226MG-T
Table 4: Recommended Output Capacitors
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 18
Best Performance Smallest Solution Size
CIN = 22µF/1206 CIN = 22µF/1206
COUT = 100µF/1206 + 2x47µF/1206, RA = 200k
V
OUT 1.8V, COUT = 2x47µF/0805
3.3V > VOUT> 1.8V, COUT = 2x47µF/1206
PVIN
(V)
VOUT
(V)
CA
(pF)
RCA
(k)
REA
(k)
Ripple
(mV)
Deviation
(mV)
PVIN
(V)
VOUT
(V)
RA
(k)
CA
(pF)
RCA
(k)
REA
(k)
Ripple
(mV)
Deviation
(mV)
14V
0.9V 15 8.2 0 5.29 26
14V
0.9V 200 10 0.2 Open 15 51
1.2V 12 8.2 0 6.6 22 1.2V 200 10 0.2 Open 19 68
1.5V 12 12 0 8.39 24 1.5V 200 10 0.2 Open 24 66
1.8V 10 12 0 9.7 28 1.8V 200 8.2 0.2 Open 24 66
2.5V 10 12 56 18.8 54 2.5V 120 8.2 15
Open 43 86
3.3V 8.2 18 56 28.8 54 3.3V 120 6.8 15
Open 52 106
5.0V 6.8 12 56 52.1 66 5.0V 120 5.6 0.2
Open 66 152
12V
0.9V 15 8.2 0 5.22 28
12V
0.9V 200 12 0.2 Open 17 57
1.2V 15 8.2 0 6.51 22 1.2V 200 12 0.2
Open 18 70
1.5V 12 12 0 7.5 28 1.5V 200 12 0.2 Open 24 70
1.8V 10 12 0 9 34 1.8V 200 10 0.2 Open 26 80
2.5V 12 12 56 16.8 50 2.5V 120 10 15
Open 39 94
3.3V 10 18 56 27.3 54 3.3V 120 10 15
Open 45 114
5.0V 8.2 12 56 48.5 74 5.0V 120 6.8 0.2
Open 56 164
10V
0.9V 18 8.2 0 5.01 28
10V
0.9V 200 18 0.2 Open 15 69
1.2V 18 8.2 0 6.11 26 1.2V 200 18 0.2
Open 19 67
1.5V 15 12 0 7.3 28 1.5V 200 15 0.2 Open 23 78
1.8V 12 12 0 8.13 32 1.8V 200 12 0.2 Open 29 94
2.5V 15 12 56 16.8 44 2.5V 120 15 15
Open 29 98
3.3V 12 18 56 27.2 68 3.3V 120 12 15
Open 44 128
5.0V 10 12 56 42 84 5.0V 120 10 0.2
Open 52 192
8V
0.9V 22 8.2 0 4.92 26
8V
0.9V 200 27 0.2 Open 16 68
1.2V 18 8.2 0 5.41 32 1.2V 200 22 0.2
Open 19 75
1.5V 15 12 0 6.48 32 1.5V 200 22 0.2 Open 23 82
1.8V 15 12 0 7.32 36 1.8V 200 18 0.2 Open 27 104
2.5V 18 12 56 16.1 64 2.5V 120 27 6.8
Open 36 124
3.3V 15 18 56 24 72 3.3V 120 22 6.8
Open 36 152
5.0V 12 12 56 31.4 102 5.0V 120 12 0.2
Open 40 236
6.6V
0.9V 22 8.2 0 4.6 30
6.6V
0.9V 200 33 0.2 Open 14 70
1.2V 22 8.2 0 5.59 32 1.2V 200 33 0.2
Open 17 80
1.5V 18 12 0 5.88 36 1.5V 200 27 0.2 Open 21 96
1.8V 18 12 0 7.12 38 1.8V 200 27 0.2 Open 24 110
2.5V 22 12 56 15.4 56 2.5V 120 39 4.3
Open 29 140
3.3V 18 18 56 21.6 78 3.3V 120 27 4.3
Open 28 184
5V
0.9V 27 8.2 0 3.93 32
5V
0.9V 200 68 0.2 Open 13 80
1.2V 22 8.2 0 4.4 38 1.2V 200 56 0.2 Open 15 92
1.5V 22 12 0 5.91 38 1.5V 200 47 0.2 Open 17 106
1.8V 22 12 0 6.91 42 1.8V 200 39 0.2 Open 19 124
2.5V 27 12 56 13.6 76 2.5V 120 68 0.2
Open 21 172
Table 5: RA, CA, RCA and REA Values for Various PVIN/VOUT Combinations: Smallest Solution Size vs. Best
Performance. See Figure 8. Use the equation in Figure 8 to calculate RB.
Note 6: Nominal Deviation is for a 6A load transient step.
Note 7: For compensation values of output voltage in between the specified output voltages, choose compensation values
of the lower output voltage setting.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 19
Thermal Considerations
Thermal considerations are important power supply
design facts that cannot be avoided in the real
world. Whenever there are power losses in a
system, the heat that is generated by the power
dissipation needs to be accounted for. The Enpirion
PowerSoC helps alleviate some of those concerns.
The Enpirion EN2360QI DC-DC converter is
packaged in an 8x11x3mm 68-pin QFN package.
The QFN package is constructed with copper lead
frames that have exposed thermal pads. The
exposed thermal pad on the package should be
soldered directly on to a copper ground pad on the
printed circuit board (PCB) to act as a heat sink.
The recommended maximum junction temperature
for continuous operation is 125°C. Continuous
operation above 125°C may reduce long-term
reliability. The device has a thermal overload
protection circuit designed to turn off the device at
an approximate junction temperature value of
150°C.
The following example and calculations illustrate
the thermal performance of the EN2360QI.
Example:
VIN = 12V
VOUT = 3.3V
IOUT = 6A
First calculate the output power.
POUT = 3.3V x 6A = 19.8W
Next, determine the input power based on the
efficiency () shown in Figure 9.
Figure 9: Efficiency vs. Output Current
For VIN = 12V, VOUT = 3.3V at 6A, 90%
= POUT / PIN = 87% = 0.87
PIN = POUT /
PIN 13.2W / 0.87 22.76W
The power dissipation (PD) is the power loss in the
system and can be calculated by subtracting the
output power from the input power.
PD = PIN – POUT
22.76W – 19.8W 2.96W
With the power dissipation known, the temperature
rise in the device may be estimated based on the
theta JA value (JA). The JA parameter estimates
how much the temperature will rise in the device for
every watt of power dissipation. The EN2360QI has
a JA value of 16 ºC/W without airflow.
Determine the change in temperature (T) based
on PD and JA.
T = PD x JA
T 2.96W x 16°C/W = 47.36°C 47°C
The junction temperature (TJ) of the device is
approximately the ambient temperature (TA) plus
the change in temperature. We assume the initial
ambient temperature to be 25°C.
TJ = TA + T
TJ 25°C + 47°C 72°C
The maximum operating junction temperature
(TJMAX) of the device is 125°C, so the device can
operate at a higher ambient temperature. The
maximum ambient temperature (TAMAX) allowed can
be calculated.
TAMAX = TJMAX – PD x JA
125°C – 47°C 78°C
The maximum ambient temperature the device can
reach is 78°C given the input and output conditions.
Note that the efficiency will be slightly lower at
higher temperatures and this calculation is an
estimate.
0
10
20
30
40
50
60
70
80
90
100
00.511.522.533.544.555.56
EFFICIENCY (%)
OUTPUT CURRENT (A)
Efficiency vs. Output Current
VOUT = 3.3V
VOUT = 1.8V
VOUT = 1.2V
CONDITIONS
V
IN
= 12.0V
AVIN = 3.3V
Dual Supply
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 20
Engineering Schematic
Figure 10: Engineering Schematic with Engineering Notes
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 21
Layout Recommendation
Figure 11: Top Layer Layout with Critical Components
(Top View). See Figure 10 for corresponding schematic.
This layout only shows the critical components and
top layer traces for minimum footprint in single-
supply mode with ENABLE tied to AVIN. Alternate
circuit configurations & other low-power pins need
to be connected and routed according to customer
application. Please see the Gerber files at
www.enpirion.com for details on all layers.
Recommendation 1: Input and output filter
capacitors should be placed on the same side of
the PCB, and as close to the EN2360QI package
as possible. They should be connected to the
device with very short and wide traces. Do not use
thermal reliefs or spokes when connecting the
capacitor pads to the respective nodes. The +V and
GND traces between the capacitors and the
EN2360QI should be as close to each other as
possible so that the gap between the two nodes is
minimized, even under the capacitors.
Recommendation 2: The PGND connections for
the input and output capacitors on layer 1 need to
have a slit between them in order to provide some
separation between input and output current loops.
Recommendation 3: The system ground plane
should be the first layer immediately below the
surface layer. This ground plane should be
continuous and un-interrupted below the converter
and the input/output capacitors.
Recommendation 4: The thermal pad underneath
the component must be connected to the system
ground plane through as many vias as possible.
The drill diameter of the vias should be 0.33mm,
and the vias must have at least 1 oz. copper plating
on the inside wall, making the finished hole size
around 0.20-0.26mm. Do not use thermal reliefs or
spokes to connect the vias to the ground plane.
This connection provides the path for heat
dissipation from the converter.
Recommendation 5: Multiple small vias (the same
size as the thermal vias discussed in
recommendation 4) should be used to connect
ground terminal of the input capacitor and output
capacitors to the system ground plane. It is
preferred to put these vias along the edge of the
GND copper closest to the +V copper. These vias
connect the input/output filter capacitors to the
GND plane, and help reduce parasitic inductances
in the input and output current loops. If vias cannot
be placed under the capacitors, then place them on
both sides of the slit in the top layer PGND copper.
Recommendation 6: AVIN is the power supply for
the small-signal control circuits. It should be
connected to the input voltage at a quiet point. In
Figure 11 this connection is made at the input
capacitor.
Recommendation 7: The layer 1 metal under the
device must not be more than shown in Figure 11.
Refer to the section regarding Exposed Metal on
Bottom of Package. As with any switch-mode
DC/DC converter, try not to run sensitive signal or
control lines underneath the converter package on
other layers.
Recommendation 8: The VOUT sense point should
be just after the last output filter capacitor. Keep the
sense trace short in order to avoid noise coupling
into the node. Contact Enpirion Technical Support
for any remote sensing applications.
Recommendation 9: Keep RA, CA, RB, and RCA
close to the VFB pin (Refer to Figure 11). The VFB
pin is a high-impedance, sensitive node. Keep the
trace to this pin as short as possible. Whenever
possible, connect RB directly to the AGND (pin 52,
53) instead of going through the GND plane.
Recommendation 10: Follow all the layout
recommendations as close as possible to optimize
performance. Enpirion provides schematic and
layout reviews for all customer designs. Contact
Enpirion Applications Engineering for detailed
support (techsupport@enpirion.com).
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 22
Design Considerations for Lead-Frame Based Modules
Exposed Metal on Bottom of Package
Lead-frames offer many advantages in thermal performance, in reduced electrical lead resistance, and in
overall foot print. However, they do require some special considerations.
In the assembly process lead frame construction requires that, for mechanical support, some of the lead-frame
cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several
small pads being exposed on the bottom of the package, as shown in Figure 10.
Only the thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board.
The PCB top layer under the EN2360QI should be clear of any metal (copper pours, traces, or vias) except for
the thermal pad. The “shaded-out” area in Figure 10 represents the area that should be clear of any metal on
the top layer of the PCB. Any layer 1 metal under the shaded-out area runs the risk of undesirable shorted
connections even if it is covered by soldermask.
The solder stencil aperture should be smaller than the PCB ground pad. This will prevent excess solder from
causing bridging between adjacent pins or other exposed metal under the package. Please consult the
Enpirion Manufacturing Application Note for more details and recommendations.
Figure 12: Lead-Frame exposed metal (Bottom View)
Shaded area highlights exposed metal that is not to be mechanically or electrically connected to the PCB.
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 23
Recommended PCB Footprint
Figure 13: EN2360QI PCB Footprint (Top View)
07514 September 17, 2012 Rev: A
EN2360QI
©Enpirion 2012 all rights reserved, E&OE Enpirion Confidential www.enpirion.com, Page 24
Package and Mechanical
Figure 14: EN2360QI Package Dimensions (Bottom View)
Packing and Marking Information: http://www.enpirion.com/resource-center-packing-and-marking-information.htm
Contact Information
Enpirion, Inc.
Perryville III Corporate Park
53 Frontage Road - Suite 210
Hampton, NJ 08827 USA
Phone: 1.908.894.6000
Fax: 1.908.894.6090
Enpirion reserves the right to make changes in circuit design and/or specifications at any time without notice. Information furnished by Enpirion is
believed to be accurate and reliable. Enpirion assumes no responsibility for its use or for infringement of patents or other third party rights, which may
result from its use. Enpirion products are not authorized for use in nuclear control systems, as critical components in life support systems or equipment
used in hazardous environment without the express written authority from Enpirion
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Altera:
EN2360QI-E EN2360QI EVB-EN2360QI