PRODUCT DATASHEET Cindy series last update 9/8/2012 Ordering number C10982_CINDY-S Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Cindy Reflector CL-L233 Metal 22.6 mm 12.5 mm Hexagonal PC Glue Ready FWHM Efficiency cd/lm Gerber File 35 degrees 85 % 1.400 Available FWHM Efficiency cd/lm Gerber File 47 degrees 81 % 1.500 Available FWHM Efficiency cd/lm Gerber File 48 degrees 82 % 1.100 Available Ordering number C10983_CINDY-M Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Cindy Reflector CL-L233 Metal 22.6 mm 12.5 mm Hexagonal PC Glue Ready Ordering number C12211_CINDY-M2 Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Cindy Reflector CL-L233 Metal 22.6 mm 12.5 mm Hexagonal PC Glue Ready No metal coating on back side. Ordering number C10984_CINDY-W Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Cindy Reflector CL-L233 Metal 22.6 mm 12.5 mm Hexagonal PC Glue Ready FWHM Efficiency cd/lm Gerber File 59 degrees 88 % 1.100 Available December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001 PRODUCT DATASHEET Cindy series last update 9/8/2012 NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001 PRODUCT DATASHEET Cindy series last update 9/8/2012 GENERAL INFORMATION - Product series especially designed & optimized for CL-L233 series of LEDs. - Special care taken to make light distribution as uniform as possible. - Reflector is made of aluminium coated PC (120 degrees of Celcius / 248 degrees of Fahrenheit) with protective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit). - Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. http://www.ledil.com/datasheets/DataSheet_GLUES.pdf NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001