PRODUCT DATASHEET
Cindy series
last update 9/8/2012
Ordering number
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
C10982_CINDY-S
Cindy
Reflector
CL-L233
Metal
22.6 mm
12.5 mm
Hexagonal
PC
-
Glue
Ready
FWHM
Efficiency
cd/lm
Gerber File
35 degrees
85 %
1.400
Available
Ordering number
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
C10983_CINDY-M
Cindy
Reflector
CL-L233
Metal
22.6 mm
12.5 mm
Hexagonal
PC
-
Glue
Ready
FWHM
Efficiency
cd/lm
Gerber File
47 degrees
81 %
1.500
Available
Ordering number
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
C12211_CINDY-M2
Cindy
Reflector
CL-L233
Metal
22.6 mm
12.5 mm
Hexagonal
PC
-
Glue
Ready
FWHM
Efficiency
cd/lm
Gerber File
48 degrees
82 %
1.100
Available
No metal coating on back side.
Ordering number
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
C10984_CINDY-W
Cindy
Reflector
CL-L233
Metal
22.6 mm
12.5 mm
Hexagonal
PC
-
Glue
Ready
FWHM
Efficiency
cd/lm
Gerber File
59 degrees
88 %
1.100
Available
December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
PRODUCT DATASHEET
Cindy series
last update 9/8/2012
NOTE: The typical divergence will be changed by different color, chip size and chip position
tolerance. The typical total divergence is the full angle measured where the luminous intensity
is half of the peak value.
December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
PRODUCT DATASHEET
Cindy series
last update 9/8/2012
GENERAL INFORMATION
- Product series especially designed & optimized for CL-L233 series of LEDs.
- Special care taken to make light distribution as uniform as possible.
- Reflector is made of aluminium coated PC (120 degrees of Celcius / 248 degrees of Fahrenheit) with
protective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit).
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue
options.
http://www.ledil.com/datasheets/DataSheet_GLUES.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end
product. For example, mechanical stress, vibration and holes on the surface of the circuit boar
weaken the strength of the glue.
NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If
cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED
manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other
electronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fiber
cloth may be used to remove fingerprints or other traces from handling.
December 25th 2012 11:34 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
