EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LED with Right Angle Lens 12-215/S2C-AQ1R1L/3C Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. Descriptions The 12-215 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Part No. Material 12-215/S2C-AQ1R1L/3C AlGaInP Emitted Color Brilliant Orange Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Package Outline Dimensions CL 0.6 CL 1.7 0.2 2.1 0.2 0.5 1.0 0.2 R0.5 1.5 0.5 2.2 Cathode mark 0.9 Note: The tolerances unless mentioned is 0.1mm, Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 2 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +90 Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering:260 for 10 sec Soldering Temperature Tsol Hand Soldering:350 for 3 sec Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 72 ----- 140 mcd Peak Wavelength p ---- 611 ---- nm Dominant Wavelength Spectrum Radiation Bandwidth d 600.5 ----- 612.5 nm ----- 17 ---- nm Viewing Angle 21/2 ----- 130 ---- deg Forward Voltage VF 1.70 ----- 2.30 V Reverse Current IR ---- ---- 10 A Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 3 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Bin Range Of Dom. Wavelength Groups A Bin Min Max D8 600.5 603.5 D9 603.5 606.5 D10 606.5 609.5 D11 609.5 612.5 Unit Condition nm IF =20mA Unit Condition mcd IF =20mA Unit Condition V IF =20mA Bin Range Of Luminous Intensity Bin Min Max Q1 72.0 90.0 Q2 90.0 112 R1 112 140 Bin Range Of Luminous Voltage Groups L Bin Min Max 19 1.70 1.80 20 1.80 1.90 21 1.90 2.00 22 2.00 2.10 23 2.10 2.20 24 2.20 2.30 Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 4 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Electro-Optical Characteristics (Ta=25) Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 5 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 6 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 7 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 8 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package:The LEDs should be kept at 30 or less and 90%RH or less. 2.3After opening the package:The LEDs should be kept at 30 or less and 70%RH or less.(Floor life) However,it's recommended that the LEDs should be used within 168 hours (7 days) after opening the package.If unusede LEDs remain,it should be stored in moisture proof packages. 3. If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 9 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu EVERLIGHT ELECTRONICS CO.,LTD. 12-215/S2C-AQ1R1L/3C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 10 of 10 Device No:SZDSE-125-S02 Prepared date: 23-Feb-2005 Prepared by: Xiaowei Wu