QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 593 EVALUATION CARD FOR THE LT1637 IN THE DFN PACKAGE LT1637CDD DESCRIPTION Demonstration circuit 593 simplifies the evaluation of the LT1637CDD op amp in the tiny, 3mm x 3mm, DFN (Dual in-line, Flat, No-leads) chip-scale package. Electrical performance of this LT1637 is the same as previous versions. This version is only a packaging enhancement. An evaluation circuit can easily be built on this board without handling the tiny DFN device. Pads are provided for adding external components and holes are available for jumpers, signal I/O and supply wires. Supply bypass capacitors are already on the board. Alternatively adding two 4-pin headers (0.1" spacing) converts the board to a standard 8-pin DIP format for use with a socket on a second circuit board. The backside of this evaluation board is void of metal to allow wiring into an existing system with the board resting on top of other components. About the LT1637CDD The LT1637 is an Over-The-Top, Micropower, Rail-to-Rail Input and Output Op Amp Input Common Mode Range Extends 44V Above V- Independent of V+ 190A Supply Current, 25mA Output Current Reverse Battery Protected to 25V Drives 4700pF CLOAD with compensation Output Shutdown, ISUPPLY = 3A Output Swings to Within 3mV of V- and 25mV of V+ Total Supply Voltage Range: 2.7V to 44V Table 1. Typical Performance Summary (Single 3V Supply, TA=25C) Visit www.linear.com for complete data sheet. PARAMETER CONDITION VALUE Input Voltage Range Min and Max 0V to 44V Supply Current 190A Offset Voltage (Null pins provided) 100V Input Bias Current 20nA Gain Bandwidth Product 1MHz Slew Rate 0.35 V/sec Device Top Mark Identifier: LAAK 1 QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 593 EVALUATION CARD FOR THE LT1637 IN THE DFN PACKAGE QUICK START PROCEDURE Build the evaluation circuit in one of two ways as shown in Figures 1 and 2. VCC GND VEE C1 C3 R2 EOUT R4 C4 LA xx R1 EIN GND R3 GND C2 Figure 1. External Components Directly on the PCB (0.1*F Bypass Capacitors: AVX 1206C104KAT). Example connections shown may not be correct for this device. GROUND WIRE FOR BYPASS CAPS DEMONSTRATION CIRCUIT DFN PACKAGE 8-PIN DIP SOCKET HEADER: MILL-MAX 3402-0-00-21-00-00-03-0 TEST BOARD Figure 2. Convert the Board to an 8-pin DIP Format 2 QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 593 EVALUATION CARD FOR THE LT1637 IN THE DFN PACKAGE PACKAGE AND CONNECTION DRAWING R = 0.115 TYP 5 0.38 0.10 8 0.58 0.05 3.35 0.05 1.65 0.05 2.25 0.05 (2 SIDES) 3.00 0.10 (4 SIDES) PACKAGE OUTLINE 1.65 0.10 (2 SIDES) PIN 1 TOP MARK (DD8) DFN 0902 0.28 0.05 0.75 0.05 0.200 REF 4 0.28 0.05 1 0.50 BSC 0.50 BSC 2.38 0.05 (2 SIDES) 0.00 - 0.05 2.38 0.10 (2 SIDES) BOTTOM VIEW--EXPOSED PAD RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED TOP VIEW NULL 1 8 NULL -IN 2 7 V+ +IN 3 6 OUT - 5 SHDN V 4 DD PACKAGE 8-LEAD (3mm x 3mm) PLASTIC DFN ASSEMBLY TIPS Following are the recommended procedures for soldering surface mount packages to PC boards. - Activation temperature 130C to 150C Reflow Soldering with Solder Paste - Time above 183C for 30 seconds * Use of solder plated boards is recommended. * Screen solder paste on board. * Mount components on board. * Infrared or forced hot air convection reflow is recommended for best performance. Parameters: - Preheat peak temperature 125C 15C and 2C to 4C per second rise - Reflow begins at 183C (63Sn/37Pb) - Peak package body temperature 220C to 245C - Dwell time at peak temperature 10 seconds max - Cooling rate 2C to 4C per second - Clean boards. * For Vapor Phase Reflow, recommended parameter ranges for: - Heating rate: 4C per second max 3 QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 593 EVALUATION CARD FOR THE LT1637 IN THE DFN PACKAGE - Preheat temperature: 45C to 80C - Time above 200C: 50 seconds to 90 seconds - Peak package temperature: 212C to 219C Wave Soldering and Hand Soldering are not recommended. REWORK GUIDELINES FOR DFN PACKAGES Each package mounting site should be reworked one at a time only, to ensure maximum quality and reliability. Linear Technology has found the following rework procedure to be effective with DFN packages but by no means excludes other methods more suited to specific manufacturing needs. Reflow Temperature Profile Each package site to be reworked should be individually heated. The reflow temperature profile can be established using a hot gas tool and a thermocouple embedded in the solder joints of a sample setup unit on the PCB. Preheating and Package Removal A package rework tool with vacuum pickup similar to the A.P.E. Flo-Master can be used. A bottom PCB heater is required to provide preheating of the PCB to approximately 110C to 120C. The rework nozzle must be centered with respect to the package in order to direct the hot gas flow over the top of the package while limiting the temperature of the adjacent components to prevent solder reflow. Site Rework With a combination on hot gas/vacuum desoldering tool and solder wick ribbons (if necessary), remove the package and any remaining solder residues. Use a minimal amount of flux if it is required to remove solder residue. This will also assist in leaving a smooth, flat surface for the reattachment of a replacement unit. The site for the package should be thoroughly cleaned with isopropyl alcohol (IPA) and dried with clean dry air (CDA). Solder Paste Application Solder paste may be screen printed on to the package landing site and exposed heat sink pads. Stainless steel stencils are recommended for solder paste application. The printed solder deposits should be 100 percent inspected for uniformity of size and shape. Some applications may have severe space constraints preventing screen printing to be accomplished on the PCB. Therefore, solder paste can be directly applied to the packages landing site and exposed heatsink pad. The package is to be picked and placed using a vision aided system similar to the A.P.E. Sniper SMD 7007 Rework System. Reflow Process The replacement package, once it has been placed onto the reworked PCB landing site, should be reflowed on the PCB using a hot gas tool on the top of the package and a heater on the bottom of the PCB. The reflow temperature should not exceed 240C. Note that liquidus temperature for 63/37 Sn/Pb solder is 183C. Make sure to limit adjacent components to below the solder reflow temperature. The solder paste manufacturer's recommended reflow temperature profile/specifications must be complied with to avoid damage to the PCB and/or adjacent components. A 100 percent post rework visual inspection for good joint wetting is recommended. 4