Enpirion(R) Power Datasheet EP5352QI/EP5362QI/EP5382QI 500/600/800mA PowerSoC Synchronous Buck Regulators With Integrated Inductor Product Overview VIN The Ultra-Low-Profile EP53X2QI product family is targeted to applications where board area and profile are critical. EP53X2QI is a complete power conversion solution requiring only two low cost ceramic MLCC caps. Inductor, MOSFETS, PWM, and compensation are integrated into a tiny 5mm x 4mm x 1.1mm QFN package. The EP53x2QI family is engineered to simplify design and to minimize layout constraints. High switching frequency and internal type III compensation provides superior transient response. With a 1.1 mm profile, the EP53x2 is perfect for space and height limited applications. UVLO Thermal Limit Current Limit ENABLE Soft Start P-Drive (-) Logic VOUT PWM Comp (+) N-Drive GND VSENSE Sawtooth Generator Compensation Network (-) Switch Error Amp VFB (+) DAC VREF Voltage Select A 3-pin VID output voltage select scheme provides seven pre-programmed output voltages along with an option for external resistor divider. Output voltage can be programmed on-the-fly to provide fast, dynamic voltage scaling. Package Boundry VS0 VS1 VS2 Product Highlights Typical Application Circuit * Revolutionary integrated inductor * Very small solution foot print* * Fully RoHS compliant; MSL 3 260C reflow * Only two low cost components required * 5mm x 4mm x1.1mm QFN package * Wide 2.4V to 5.5V input range * 500, 600, 800 mA output current versions * Less than 1 A standby current * 4 MHz switching frequency * Fast transient response * Very low ripple voltage; 5mVp-p typical * 3 Pin VID Output Voltage select * External divider option * Dynamically adjustable output * Designed for Low noise/EMI * Short circuit, UVLO, and thermal protection Vin Voltage Select VOUT Vout 2.2uF 10F VFB VS0 VS1 VS2 GND Figure 1. Typical application circuit. Applications * * * * * * Area constrained applications Mobile multimedia, smartphone & PDA Mobile and Cellular platforms VoIP and Video phones Personal Media Players FPGA, DSP, IO & Peripherals 1 03132 VSense ENABLE VIN October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Absolute Maximum Ratings CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond recommended operating conditions is not implied. Stress beyond absolute maximum ratings may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. PARAMETER Input Supply Voltage Voltages on: ENABLE, VSENSE, VS0-VS2 Voltage on: VFB Storage Temperature Range Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A ESD Rating (based on Human Body Model) SYMBOL VIN MIN -0.3 -0.3 -0.3 -65 TSTG MAX 7.0 VIN + 0.3 2.7 150 260 2000 UNITS V V V C C V Recommended Operating Conditions PARAMETER Input Voltage Range Output Voltage Range Operating Ambient Temperature Operating Junction Temperature SYMBOL VIN VOUT TA TJ MIN 2.4 0.6 -40 -40 MAX 5.5 VIN-0.45 +85 +125 UNITS V V C C Thermal Characteristics PARAMETER Thermal Resistance: Junction to Ambient (0 LFM) Thermal Resistance: Junction to Case (0 LFM) Thermal Shutdown Thermal Shutdown Hysteresis SYMBOL JA JC TJ-TP TYP 65 15 +150 15 UNITS C/W C/W C C Electrical Characteristics NOTE: TA = 25C unless otherwise noted. Typical values are at VIN = 3.6V. EP5352QI, EP5362QI: CIN = 2.2F, COUT=10uF. EP5382QI: CIN = 4.7F, COUT=10uF. PARAMETER Operating Input Voltage Under Voltage Lockout UVLO Hysteresis SYMBOL VIN VUVLO TEST CONDITIONS MIN 2.4 MAX 5.5 2.3 UNITS V V V -2.0 +2.0 % -3.0 +3.0 % VIN going low to high 2.4V VIN 5.5V, ILOAD = 100mA; TA = 25C 2.4V VIN 5.5V, ILOAD = 0 - 800mA, TA = -40C to +85C TYP 2.2 0.145 VOUT Initial Accuracy VOUT VOUT Variation for all Causes VOUT Feedback Pin Voltage VFB 2.4V VIN 5.5V, ILOAD = 100mA VSO=VS1=VS2=1 0.591 0.603 0.615 Feedback Pin Input Current Feedback Pin Voltage IFB VFB 2.4V VIN 5.5V, ILOAD = 0-800mA, 0.585 1 0.603 0.621 2 03132 October 11, 2013 V nA V www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI PARAMETER SYMBOL Dynamic Voltage Slew Rate Continuous Output Current EP5352QI Continuous Output Current EP5362QI Continuous Output Current EP5382QI Shut-Down Current Quiescent Current Vslew PFET OCP Threshold VS0-VS1 Voltage Threshold VS0-VS2 Pin Input Current TYP MAX 3 UNITS V/mS EP5352QI 500 mA IOUT EP5362QI 600 mA IOUT EP5382QI 800 mA ISD Enable = Low No switching 2.4V VIN 5.5V, 0.6V VOUT VIN - 0.6V Pin = Low Pin = High ILIM 1.4 IEN FOSC RDS(ON) RDS(ON) VSS TSS 0.75 800 A A 2 A 0.0 1.4 IVSX 0.4 VIN 1 Logic Low Logic High VIN = 3.6V 0.0 1.4 VID programming mode VFB programming mode 1.95 1.56 October 11, 2013 3 2.4 V nA 0.2 VIN 2 4 340 270 .110 3 03132 MIN IOUT Enable Voltage Threshold Enable Pin Input Current Operating Frequency PFET On Resistance NFET On Resistance Internal Inductor DCR Soft-Start Operation Soft-Start Slew Rate VOUT Rise Time TEST CONDITIONS TA = -40C to +85C VSO=VS1=VS2=1 4.05 3.24 V A MHz m m V/mS mS www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI VFB VIN 2 15 VSENSE GND 3 14 GND 4 13 VOUT 5 12 VOUT 6 11 VFB VS0 ENABLE 19 20 Thermal Pad 16 1 VIN 2 VIN VSENSE 15 NC NC 14 3 GND NC NC 13 4 GND NC NC 12 5 VOUT NC NC 11 6 VOUT 8 7 NC VOUT NC NC 10 NC 9 9 NC NC 8 VOUT 10 7 Figure 3. Pin description, bottom view. Figure 2. Pin description, top view. VFB (Pin 16): Feed back pin for external divider option. When using the external divider option (VS0=VS1=VS2= high) connect this pin to the center of the external divider. Set the divider such that VFB = 0.603V. VIN (Pin 1,2): Input voltage pin. Supplies power to the IC. VIN can range from 2.4V to 5.5V. Input GND: (Pin 3): Input power ground. Connect this pin to the ground terminal of the input capacitor. Refer to Layout Recommendations for further details. VS0,VS1,VS2 (Pin 17,18,19): Output voltage select. VS0=pin19, VS1=pin18, VS2=pin17. Selects one of seven preset output voltages or choose external divider by connecting pins to logic high or low. Logic low is defined as VLOW 0.4V. Logic high is defined as VHIGH 1.4V. Any level between these two values is indeterminate. (refer to section on output voltage select for more detail). Output GND: (Pin 4): Power ground. The output filter capacitor should be connected to this pin. Refer to Layout recommendations for further detail. VOUT (Pin 5,6,7): Regulated output voltage. NC (Pin 8,9,10,11,12,13,14): These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. ENABLE (Pin 20): Output enable. Enable = logic high, disable = logic low. Logic low is defined as VLOW 0.2V. Logic high is defined as VHIGH 1.4V. Any level between these two values is indeterminate. VSENSE (Pin 15): Sense pin for output voltage regulation. Connect VSENSE to the output voltage rail as close to the terminal of the output filter capacitor as possible. Thermal Pad. Thermal pad to remove heat from package. Connect to surface ground pad and PCB internal ground plane. 4 03132 VS1 VS2 17 16 18 VS1 18 1 VS2 VS0 19 VIN 17 ENABLE 20 Pin Description October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Functional Block Diagram VIN UVLO Thermal Limit Current Limit ENABLE Soft Start P-Drive (-) Logic VOUT PWM Comp (+) N-Drive GND VSENSE Sawtooth Generator Compensation Network (-) Switch Error Amp VFB (+) DAC Voltage Select VREF Package Boundry VS0 VS1 VS2 Figure 4. Functional block diagram. 5 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Typical Performance Characteristics Efficiency vs Output Current Efficiency vs Output Current 100 95 90 90 85 85 Efficiency -% Efficiency -% 95 80 V OUT = 3.3V 75 V OUT = 3.0V 70 V OUT = 2.7V 65 V OUT = 3.3V 75 V OUT = 3.0V 70 V OUT = 2.7V V OUT = 2.5V 65 V OUT = 2.5V V OUT = 1.8V 60 V OUT = 1.8V 60 80 55 55 VIN = 5.0V VIN = 3.6V 50 50 50 50 150 250 350 450 550 150 250 350 450 550 Load Current (mA) Load Current (mA) Efficiency vs Output Current 100 95 90 Efficiency -% 85 80 75 70 V OUT = 3.0V V OUT = 2.7V 65 V OUT = 2.5V 60 V OUT = 1.8V 55 V OUT = 1.2V VIN = 3.3V 50 50 150 250 350 450 550 Load Current (mA) 6 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Detailed Description associated with switch-mode DCDC converters. All of this enables much easier and faster integration into various applications to meet demanding EMI requirements. Functional Overview The EP53x2QI family is a complete DCDC converter solution requiring only two low cost MLCC capacitors. MOSFET switches, PWM controller, Gate-drive, compensation, and inductor are integrated into the tiny 5mm x 4mm x 1.1mm package to provide the smallest footprint possible while maintaining high efficiency and high performance. The converter uses voltage mode control to provide the simplest implementation and high noise immunity. The device operates at a 4 MHz switching frequency. The high switching frequency allows for a wide control loop bandwidth providing excellent transient performance. The 4 MHz switching frequency enables the use of very small components making possible this unprecedented level of integration. Output voltage is chosen from seven preset values via a three pin VID voltage select scheme. An external divider option enables the selection of any voltage in the 0.6 to VIN Vdropout. This reduces the number of components that must be qualified and reduces inventory problems. The VID pins can be toggled on the fly to implement glitch free dynamic voltage scaling. Protection features include under-voltage lockout (UVLO), over-current protection (OCP), short circuit protection, and thermal overload protection. Altera Enpirion's proprietary power MOSFET technology provides very low switching loss at frequencies of 4 MHz and higher, allowing for the use of very small internal components, and very wide control loop bandwidth. Unique magnetic design allows for integration of the inductor into the very low profile 1.1mm package. Integration of the inductor virtually eliminates the design/layout issues normally Integrated Inductor Altera has introduced the world's first product family featuring integrated inductors. The EP53x2QI family utilizes a low loss, planar construction inductor. The use of an internal inductor localizes the noises associated with the output loop currents. The inherent shielding 7 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI The above number and formula assume a no load condition at startup. and compact construction of the integrated inductor reduces the radiated noise that couples into the traces of the circuit board. Further, the package layout is optimized to reduce the electrical path length for the AC ripple currents that are a major source of radiated emissions from DCDC converters. The integrated inductor significantly reduces parasitic effects that can harm loop stability, and makes layout very simple. Over Current/Short Circuit Protection The current limit function is achieved by sensing the current flowing through a sense PMOSFET which is compared to a reference current. When this level is exceeded the PFET is turned off and the N-FET is turned on, pulling VOUT low. This condition is maintained for a period of 1mS and then a normal soft start is initiated. If the over current condition still persists, this cycle will repeat in a "hiccup" mode. Soft Start Internal soft start circuits limit in-rush current when the device starts up from a power down condition or when the "ENABLE" pin is asserted "high". Digital control circuitry limits the VOUT ramp rate to levels that are safe for the Power MOSFETS and the integrated inductor. Under Voltage Lockout During initial power up an under voltage lockout circuit will hold-off the switching circuitry until the input voltage reaches a sufficient level to insure proper operation. If the voltage drops below the UVLO threshold the lockout circuitry will again disable the switching. Hysteresis is included to prevent chattering between states. The EP53x2QI have two soft start operating modes. When VOUT is programmed using a preset voltage in VID mode, the device has a constant slew rate. When the EP53x2QI is configured in external resistor divider mode, the device has a constant VOUT ramp time. Output voltage slew rate and ramp time is given in the Electrical Characteristics Table. Enable The ENABLE pin provides a means to shut down the converter or enable normal operation. A logic low will disable the converter and cause it to shut down. A logic high will enable the converter into normal operation. In shutdown mode, the device quiescent current will be less than 1 uA. The ENABLE pin must not be left floating. Excess bulk capacitance on the output of the device can cause an over-current condition at startup. When operating in VID mode, the maximum total capacitance on the output, including the output filter capacitor and bulk and decoupling capacitance, at the load, is given as: Thermal Shutdown COUT_TOTAL_MAX = COUT_Filter + COUT_BULK = 350uF When excessive power is dissipated in the chip, the junction temperature rises. Once the junction temperature exceeds the thermal shutdown temperature the thermal shutdown circuit turns off the converter output voltage thus allowing the device to cool. When the junction temperature decreases by 15C, the device will go through the normal startup process. When the EP53x2QI output voltage is programmed using and external resistor divider the maximum total capacitance on the output is given as: COUT_TOTAL_MAX = 6.253x10-4/VOUT Farads Application Information 8 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Output Voltage Select To provide the highest degree of flexibility in choosing output voltage, the EP53x2QI family uses a 3 pin VID, or Voltage ID, output voltage select arrangement. This allows the designer to choose one of seven preset voltages, or to use an external voltage divider. Internally, the output of the VID multiplexer sets the value for the voltage reference DAC, which in turn is connected to the non-inverting input of the error amplifier. This allows the use of a single feedback divider with constant loop gain and optimum compensation, independent of the output voltage selected. Table 1 shows the various VS0-VS2 pin logic states and the associated output voltage levels. A logic "1" indicates a connection to VIN or to a "high" logic voltage level. A logic "0" indicates a connection to ground or to a "low" logic voltage level. These pins can be either hardwired to VIN or GND or alternatively can be driven by standard logic levels. These pins must not be left floating. VS2 VS1 VS0 VOUT 0 0 0 3.3 0 0 1 2.5 0 1 0 2.8 0 1 1 1.2 1 0 0 3.0 1 0 1 1.8 1 1 0 2.7 1 1 1 External Table 1. Voltage select settings. VSense ENABLE VIN Vin VOUT Vout 2.2uF 4.7uF Ra 10F VFB VS0 VS1 Rb VS2 GND Figure 5. External Divider. The output voltage is selected by the following formula: VOUT = 0.603V (1 + Ra Rb ) Ra must be chosen as 200K to maintain loop gain. Then Rb is given as: Rb = 1.2 x105 VOUT - 0.603 Dynamically Adjustable Output The EP53x2QI are designed to allow for dynamic switching between the predefined VID voltage levels The inter-voltage slew rate is optimized to prevent excess undershoot or overshoot as the output voltage levels transition. The slew rate is identical to the softstart slew rate of 3V/mS. Dynamic transitioning between internal VID settings and the external divider is not allowed. External Voltage Divider As described above, the external voltage divider option is chosen by connecting the VS0, VS1, and VS2 pins to VIN or logic "high". The EP53x2QI uses a separate feedback pin, VFB, when using the external divider. VSENSE must be connected to VOUT as indicated in Figure 5. Power-Up/Down Sequencing During power-up, ENABLE should not be asserted before VIN. During power down, the VIN should not be powered down before the ENABLE. Tying PVIN and ENABLE together 9 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI MLCC type capacitor be used. The output capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and temperature and are not suitable for switch-mode DC-DC converter input and output filter applications. during power-up or power-down meets this requirement. Pre-Bias Start-up The EP53x2QI does not support startup into a pre-biased condition. Be sure the output capacitors are not charged or the output of the EP53x2QI is not pre-biased when the EP53x2QI is first enabled. Cin Manufacturer Part # Murata GRM219R61A475KE19D GRM319R61A475KA01D GRM219R60J475KE01D GRM31MR60J475KA01L Input and Output Capacitors The input capacitance requirement is as follows: Panasonic EP5352QI, EP5362QI = 2.2uF Taiyo Yuden EP5382QI = 4.7uF Panasonic Taiyo Yuden Case Size 0805 1206 0805 1206 10V 0805 1206 0805 1206 6.3V LMK212BJ475KG-T LMK316BJ475KD-T JMK212BJ475KD-T 10V 0805 1206 0805 6.3V Value 2.2uF WVDC 10V 6.3V ECJ-2FB1A225K ECJ-3YB1A225K ECJ-2YB0J225K Case Size 0805 1206 0805 10V 0805 1206 0805 6.3V LMK107BJ225KA-T LMK212BJ225KG-T Cout Manufacturer Part # Murata GRM219R60J106KE19D GRM319R60J106KE01D The output capacitance requirement is a minimum of 10uF. The control loop is designed to be stable with up to 60uF of total output capacitance without requiring modification of the control loop. Capacitance above the 10uF minimum should be added if the transient performance is not sufficient using the 10uF. Altera recommends a low ESR WVDC 10V 6.3V ECJ-2FB1A475K ECJ-3YB1A475K ECJ-2FB0J475K ECJ-3YB0J475K Cin Manufacturer Part # Murata GRM21BR71A225KA01L GRM31MR71A225KA01L GRM21BR70J225KA01L Altera recommends that a low ESR MLCC capacitor be used. The input capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and with temperature, and are not suitable for switch-mode DC-DC converter input and output filter applications. Value 4.7uF Value 10uF 10V 0603 0805 WVDC 6.3V Case Size 0805 1206 Panasonic ECJ-2FB0J106K ECJ-3YB0J106K 6.3V 0805 1206 Taiyo Yuden JMK212BJ106KD-T JMK316BJ106KF-T 6.3V 0805 1206 LAYOUT CONSIDERATIONS* *Optimized PCB Layout file downloadable from http://www.altera.com/enpirion to assure first pass design success. Recommendation 1: Input and output filter capacitors should be placed as close to the EP53x2QI package as possible to reduce EMI from input and output loop AC currents. This reduces the physical area of the Input and Output AC current loops. Recommendation 2: DO NOT connect GND pins 3 and 4 together. Pin 3 should be used for the Input capacitor local ground and pin 4 should be used for the output capacitor ground. The ground pad for the input and output filter capacitors should be isolated ground islands and should be connected to system ground as indicated in recommendation 3 and recommendation 5. 10 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Recommendation 3: Multiple small vias (0.25mm after copper plating) should be used to connect ground terminals of the Input capacitor and the output capacitor to the system ground plane. This provides a low inductance path for the high-frequency AC currents, thereby reducing ripple and suppressing EMI (see Fig. 5, Fig. 6, and Fig. 7). Recommendation 4: The large thermal pad underneath the component must be connected to the system ground plane through as many thermal vias as possible. The vias should use 0.33mm drill size with minimum one ounce copper plating (0.035mm plating thickness). This provides the path for heat dissipation from the converter. Recommendation 5: The system ground plane referred to in recommendations 3 and 4 should be the first layer immediately below the surface layer (PCB layer 2). This ground plane should be continuous and un-interrupted below the converter and the input and output capacitors that carry large AC currents. If it is not possible to make PCB layer 2 a continuous ground plane, an uninterrupted ground "island" should be created on PCB layer 2 immediately underneath the EP53x2QI and its input and output capacitors. The vias that connect the input and output capacitor grounds, and the thermal pad to the ground island, should continue through to the PCB GND layer as well. Recommendation 6: As with any switch-mode DC/DC converter, do not run sensitive signal or control lines underneath the converter package. VS2 VFB VSENSE NC NC NC NC 16 15 14 13 12 11 Figure 6 shows an example schematic for the EP53x2QI using the internal voltage select. In this example, the device is set to a VOUT of 1.2V (VS2=0, VS1=1, VS0=1). 17 AGND NC 8 NC 6 VOUT VOUT 5 4 GND VOUT 3 GND NC 9 7 2 20 1 ENABLE VIN VS0 19 10 VIN VS1 18 VOUT VIN 4.7uF/2.2uF 10F (see layout recommendation 3) Figure 6. Example application, Vout=1.2V. Figure 7 shows an example schematic using an external voltage divider. VS0=VS1=VS2= "1". The resistor values are chosen to give an output voltage of 2.6V. 11 03132 October 11, 2013 www.altera.com/enpirion Rev H 10 NC 9 NC 8 NC VFB VSENSE NC NC NC NC 15 14 13 12 Ra=200K 11 6 VOUT Rb=60K VOUT 5 4 VOUT 3 GND 7 GND ENABLE 20 AGND 19 2 VS0 1 VS1 18 VIN 17 VIN VS2 16 EP5382QI/EP5362QI/EP5352QI VOUT VIN 4.7uF 10F (see layout recommendation 3) Figure 7. Schematic showing the use of external divider option, Vout = 2.6V. Figure 8 shows two example board layouts. Note the placement of the input and output capacitors. They are placed close to the device to minimize the physical area of the AC current loops. Note the placement of the vias per recommendation 3. Figure 8. Example layout showing PCB top layer, as well as demonstrating use of vias from input, output filter capacitor local grounds, and thermal pad, to PCB system ground. 12 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Ordering Information Part Number Temp Range Package EP5352QI -40C to +85C 20-pin QFN T&R EP5362QI -40C to +85C 20-pin QFN T&R EP5382QI -40C to +85C 20-pin QFN T&R EVB-EP5352QI EP5352QI Evaluation Board EVB-EP5362QI EP5362QI Evaluation Board EVB-EP5382QI EP5382QI Evaluation Board 13 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Design Considerations for Lead-Frame Based Modules Exposed Metal on Bottom Of Package Altera has developed a break-through in package technology that utilizes the lead frame as part of the electrical circuit. The lead frame offers many advantages in thermal performance, in reduced electrical lead resistance, and in overall foot print. However, it does require some special considerations. As part of the package assembly process, lead frame construction requires that for mechanical support, some of the lead-frame metal be exposed at the point where wire-bond or internal passives are attached. This results in several small pads being exposed on the bottom of the package. Only the large thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board. The PCB top layer under the EP53x2QI should be clear of any metal except for the large thermal pad. The "grayed-out" area in Figure 9 represents the area that should be clear of any metal (traces, vias, or planes), on the top layer of the PCB. NOTE: Clearance between the various exposed metal pads, the thermal ground pad, and the perimeter pins, meets or exceeds JEDEC requirements for lead frame package construction (JEDEC MO-220, Issue J, Date May 2005). The separation between the large thermal pad and the nearest adjacent metal pad or pin is a minimum of 0.20mm, including tolerances. This is shown in Figure 10. Thermal Pad. Connect to Ground plane Figure 9. Exposed metal and mechanical dimensions of the package . The gray area represents the bottom metal no-connect area. This area should be clear of any traces, planes, or vias, on the top layer of the PCB. 14 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Figure 10. Exposed pad clearances; the Altera Enpirion lead frame package complies with JEDEC requirements. 15 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Figure 11. Recommended PCB Solder Mask Openings. 16 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Figure 12. Package mechanical dimensions. 17 03132 October 11, 2013 www.altera.com/enpirion Rev H EP5382QI/EP5362QI/EP5352QI Contact Information Altera Corporation 101 Innovation Drive San Jose, CA 95134 Phone: 408-544-7000 www.altera.com (c) 2013 Altera Corporation--Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. 18 03132 October 11, 2013 www.altera.com/enpirion Rev H