BC856ALT1G Series General Purpose Transistors PNP Silicon Features www.onsemi.com * S and NSV Prefix for Automotive and Other Applications Requiring * Unique Site and Control Change Requirements; AEC-Q101 Qualified and PPAP Capable These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant COLLECTOR 3 1 BASE MAXIMUM RATINGS (TA = 25C unless otherwise noted) Rating Symbol Collector-Emitter Voltage BC856, SBC856 BC857, SBC857 BC858, NSVBC858, BC859 VCEO Collector-Base Voltage BC856, SBC856 BC857, SBC857 BC858, NSVBC858, BC859 VCBO Emitter-Base Voltage VEBO -5.0 V Collector Current - Continuous IC -100 mAdc Collector Current - Peak IC -200 mAdc Value 2 EMITTER Unit V -65 -45 -30 3 V 1 -80 -50 -30 2 SOT-23 (TO-236) CASE 318 STYLE 6 THERMAL CHARACTERISTICS MARKING DIAGRAM Characteristic Symbol Total Device Dissipation FR- 5 Board, (Note 1) TA = 25C Derate above 25C PD Thermal Resistance, Junction-to-Ambient RqJA Max Unit 225 1.8 mW mW/C 556 C/W xx M G G 1 xx Total Device Dissipation Alumina Substrate, (Note 2) TA = 25C Derate above 25C Thermal Resistance, Junction-to-Ambient Junction and Storage Temperature PD 300 2.4 mW mW/C RqJA 417 C/W TJ, Tstg -55 to +150 C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. FR-5 = 1.0 x 0.75 x 0.062 in. 2. Alumina = 0.4 x 0.3 x 0.024 in 99.5% alumina. (c) Semiconductor Components Industries, LLC, 1994 October, 2016 - Rev. 15 1 M G = Device Code xx = (Refer to page 6) = Date Code* = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or overbar may vary depending upon manufacturing location. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. Publication Order Number: BC856ALT1/D BC856ALT1G Series ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Symbol Min Typ Max Unit BC856, SBC856 Series BC857, SBC857 Series BC858, NSBVC858 BC859 Series V(BR)CEO -65 -45 -30 - - - - - - V Collector -Emitter Breakdown Voltage BC856 S, SBC856eries (IC = -10 mA, VEB = 0) BC857A, SBC857A, BC857B, SBC857B Only BC858, NSVB858, BC859 Series V(BR)CES -80 -50 -30 - - - - - - V Collector -Base Breakdown Voltage (IC = -10 mA) BC856, SBC856 Series BC857, SBC857 Series BC858, NSVBC858, BC859 Series V(BR)CBO -80 -50 -30 - - - - - - V Emitter -Base Breakdown Voltage (IE = -1.0 mA) BC856, SBC856 Series BC857, SBC857 Series BC858, NSVBC858, BC859 Series V(BR)EBO -5.0 -5.0 -5.0 - - - - - - V ICBO - - - - -15 -4.0 nA mA hFE - - 90 150 - - - - 270 - 125 180 250 220 290 475 420 520 800 - - - - -0.3 -0.65 - - -0.7 -0.9 - - -0.6 - - - -0.75 -0.82 fT 100 - - MHz Output Capacitance (VCB = -10 V, f = 1.0 MHz) Cob - - 4.5 pF Noise Figure (IC = -0.2 mA, VCE = -5.0 Vdc, RS = 2.0 kW, f = 1.0 kHz, BW = 200 Hz) BC856, SBC856, BC857, SBC857, BC858, NSVBC858 Series BC859 Series NF Characteristic OFF CHARACTERISTICS Collector -Emitter Breakdown Voltage (IC = -10 mA) Collector Cutoff Current (VCB = -30 V) Collector Cutoff Current (VCB = -30 V, TA = 150C) ON CHARACTERISTICS DC Current Gain BC856A, SBC856A, BC857A, SBC857A, BC858A (IC = -10 mA, VCE = -5.0 V) BC856B, SBC856B, BC857B, SBC857B, BC858B, NSVBC858B BC857C, SBC857C BC858C (IC = -2.0 mA, VCE = -5.0 V) BC856A, SBC856A, BC857A, SBC857A, BC858A BC856B, SBC856B, BC857B, SBC857B, BC858B, NSVBC858B, BC859B BC857C, SBC857C, BC858C, BC859C Collector -Emitter Saturation Voltage (IC = -10 mA, IB = -0.5 mA) (IC = -100 mA, IB = -5.0 mA) VCE(sat) Base -Emitter Saturation Voltage (IC = -10 mA, IB = -0.5 mA) (IC = -100 mA, IB = -5.0 mA) VBE(sat) Base -Emitter On Voltage (IC = -2.0 mA, VCE = -5.0 V) (IC = -10 mA, VCE = -5.0 V) VBE(on) V V V SMALL- SIGNAL CHARACTERISTICS Current -Gain - Bandwidth Product (IC = -10 mA, VCE = -5.0 Vdc, f = 100 MHz) dB - - - - 10 4.0 Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 2 BC856ALT1G Series BC857/BC858/BC859/SBC857/NSVBC858 -1.0 1.5 TA = 25C -0.9 VCE = -10 V TA = 25C VBE(sat) @ IC/IB = 10 -0.8 V, VOLTAGE (VOLTS) hFE , NORMALIZED DC CURRENT GAIN 2.0 1.0 0.7 0.5 -0.7 VBE(on) @ VCE = -10 V -0.6 -0.5 -0.4 -0.3 -0.2 0.3 VCE(sat) @ IC/IB = 10 -0.1 0.2 -0.2 -0.5 -1.0 -2.0 -5.0 -10 -20 -50 IC, COLLECTOR CURRENT (mAdc) 0 -0.1 -0.2 -100 -200 Figure 1. Normalized DC Current Gain 1.0 VB , TEMPERATURE COEFFICIENT (mV/ C) VCE , COLLECTOR-EMITTER VOLTAGE (V) TA = 25C -1.6 -1.2 IC = -10 mA IC = -50 mA IC = -200 mA IC = -100 mA IC = -20 mA -0.4 0 -0.02 -55C to +125C 1.2 1.6 2.0 2.4 2.8 -10 -20 -0.1 -1.0 IB, BASE CURRENT (mA) -0.2 10 Cib 7.0 TA = 25C 5.0 Cob 3.0 2.0 1.0 -0.4 -0.6 -1.0 -2.0 -4.0 -6.0 -10 -10 -1.0 IC, COLLECTOR CURRENT (mA) -100 Figure 4. Base-Emitter Temperature Coefficient f, T CURRENT-GAIN - BANDWIDTH PRODUCT (MHz) Figure 3. Collector Saturation Region C, CAPACITANCE (pF) -100 -50 Figure 2. "Saturation" and "On" Voltages -2.0 -0.8 -0.5 -1.0 -2.0 -5.0 -10 -20 IC, COLLECTOR CURRENT (mAdc) -20 -30 -40 400 300 200 150 VCE = -10 V TA = 25C 100 80 60 40 30 20 -0.5 -1.0 -2.0 -3.0 -5.0 -10 -20 -30 -50 VR, REVERSE VOLTAGE (VOLTS) IC, COLLECTOR CURRENT (mAdc) Figure 5. Capacitances Figure 6. Current-Gain - Bandwidth Product www.onsemi.com 3 BC856ALT1G Series BC856/SBC856 TJ = 25C VCE = -5.0 V TA = 25C -0.8 V, VOLTAGE (VOLTS) hFE , DC CURRENT GAIN (NORMALIZED) -1.0 2.0 1.0 0.5 VBE(sat) @ IC/IB = 10 -0.6 VBE @ VCE = -5.0 V -0.4 -0.2 0.2 VCE(sat) @ IC/IB = 10 0 -0.2 -1.0 -2.0 -5.0 -10 -20 -50 -100 -200 IC, COLLECTOR CURRENT (mA) -0.1 -0.2 -0.5 -50 -100 -200 -5.0 -10 -20 -1.0 -2.0 IC, COLLECTOR CURRENT (mA) Figure 8. "On" Voltage -2.0 -1.0 -1.6 -1.2 IC = -10 mA -20 mA -50 mA -100 mA -200 mA -0.8 -0.4 TJ = 25C 0 -0.02 -0.05 -0.1 -0.2 -0.5 -1.0 -2.0 IB, BASE CURRENT (mA) -5.0 -10 VB, TEMPERATURE COEFFICIENT (mV/ C) VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) Figure 7. DC Current Gain -20 -1.4 -1.8 -2.6 -3.0 -0.2 f, T CURRENT-GAIN - BANDWIDTH PRODUCT C, CAPACITANCE (pF) TJ = 25C Cib 10 8.0 Cob 4.0 2.0 -0.1 -0.2 -0.5 -1.0 -2.0 -5.0 -10 -20 VR, REVERSE VOLTAGE (VOLTS) -0.5 -1.0 -50 -2.0 -5.0 -10 -20 IC, COLLECTOR CURRENT (mA) -100 -200 Figure 10. Base-Emitter Temperature Coefficient 40 6.0 -55C to 125C -2.2 Figure 9. Collector Saturation Region 20 qVB for VBE VCE = -5.0 V 500 200 100 50 20 -100 -1.0 -10 IC, COLLECTOR CURRENT (mA) -50 -100 Figure 11. Capacitance Figure 12. Current-Gain - Bandwidth Product www.onsemi.com 4 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) BC856ALT1G Series 1.0 0.7 0.5 D = 0.5 0.2 0.3 0.2 0.1 0.05 SINGLE PULSE 0.1 0.07 0.05 SINGLE PULSE t1 t2 0.03 DUTY CYCLE, D = t1/t2 0.02 0.01 0.1 ZqJC(t) = r(t) RqJC RqJC = 83.3C/W MAX ZqJA(t) = r(t) RqJA RqJA = 200C/W MAX D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TC = P(pk) RqJC(t) P(pk) 0.2 0.5 1.0 2.0 10 5.0 20 t, TIME (ms) 50 100 200 500 1.0k 2.0k 5.0k 10k Figure 13. Thermal Response The safe operating area curves indicate IC-VCE limits of the transistor that must be observed for reliable operation. Collector load lines for specific circuits must fall below the limits indicated by the applicable curve. The data of Figure 14 is based upon TJ(pk) = 150C; TC or TA is variable depending upon conditions. Pulse curves are valid for duty cycles to 10% provided TJ(pk) 150C. TJ(pk) may be calculated from the data in Figure 13. At high case or ambient temperatures, thermal limitations will reduce the power that can be handled to values less than the limitations imposed by the secondary breakdown. -200 IC, COLLECTOR CURRENT (mA) 1s 3 ms -100 -50 -10 -5.0 -2.0 -1.0 TA = 25C TJ = 25C BC558, BC559 BC557 BC556 BONDING WIRE LIMIT THERMAL LIMIT SECOND BREAKDOWN LIMIT -5.0 -10 -30 -45 -65 -100 VCE, COLLECTOR-EMITTER VOLTAGE (V) Figure 14. Active Region Safe Operating Area www.onsemi.com 5 BC856ALT1G Series ORDERING INFORMATION Device BC856ALT1G Marking Package Shipping 3A SOT-23 (Pb-Free) 3,000 / Tape & Reel SBC856ALT1G* BC856ALT3G BC856BLT1G 10,000 / Tape & Reel 3B SOT-23 (Pb-Free) SBC856BLT1G* 3,000 / Tape & Reel 10,000 / Tape & Reel BC856BLT3G SBC856BLT3G* BC857ALT1G 3E SOT-23 (Pb-Free) 3,000 / Tape & Reel 3F SOT-23 (Pb-Free) 3,000 / Tape & Reel SBC857ALT1G* BC857BLT1G SBC857BLT1G* 10,000 / Tape & Reel BC857BLT3G NSVBC857BLT3G* BC857CLT1G 3G SOT-23 (Pb-Free) SBC857CLT1G* BC857CLT3G 3,000 / Tape & Reel 10,000 / Tape & Reel 3,000 / Tape & Reel BC858ALT1G 3J SOT-23 (Pb-Free) BC858BLT1G 3K SOT-23 (Pb-Free) 3L SOT-23 (Pb-Free) 10,000 / Tape & Reel BC858CLT1G SOT-23 (Pb-Free) 3,000 / Tape & Reel BC858CLT3G SOT-23 (Pb-Free) 10,000 / Tape & Reel SOT-23 (Pb-Free) 3,000 / Tape & Reel SOT-23 (Pb-Free) 10,000 / Tape & Reel SOT-23 (Pb-Free) 3,000 / Tape & Reel SOT-23 (Pb-Free) 10,000 / Tape & Reel NSVBC858BLT1G* BC858BLT3G BC859BLT1G 4B BC859BLT3G BC859CLT1G 4C BC859CLT3G For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *S and NSV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q101 Qualified and PPAP Capable. www.onsemi.com 6 BC856ALT1G Series PACKAGE DIMENSIONS SOT-23 (TO-236) CASE 318-08 ISSUE AR D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF THE BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 0.25 3 E 1 2 T HE DIM A A1 b c D E e L L1 HE T L 3X b L1 VIEW C e TOP VIEW A A1 SIDE VIEW c SEE VIEW C MIN 0.89 0.01 0.37 0.08 2.80 1.20 1.78 0.30 0.35 2.10 0 MILLIMETERS NOM MAX 1.00 1.11 0.06 0.10 0.44 0.50 0.14 0.20 2.90 3.04 1.30 1.40 1.90 2.04 0.43 0.55 0.54 0.69 2.40 2.64 --- 10 MIN 0.035 0.000 0.015 0.003 0.110 0.047 0.070 0.012 0.014 0.083 0 INCHES NOM 0.039 0.002 0.017 0.006 0.114 0.051 0.075 0.017 0.021 0.094 --- MAX 0.044 0.004 0.020 0.008 0.120 0.055 0.080 0.022 0.027 0.104 10 STYLE 6: PIN 1. BASE 2. EMITTER 3. COLLECTOR END VIEW RECOMMENDED SOLDERING FOOTPRINT* 3X 2.90 3X 0.90 0.95 PITCH 0.80 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative BC856ALT1/D