GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Key Features Applications * Operation at 2.970Gb/s, 2.970/1.001Gb/s, 1.485Gb/s, 1.485/1.001Gb/s and 270Mb/s * Supports SMPTE 425M (Level A and Level B), SMPTE 424M, SMPTE 292, SMPTE 259M-C and DVB-ASI * Integrated Reclocker * Integrated low phase noise VCO * 10-bit 3G-SDI Serial digital reclocked, or non-reclocked loop-through output Integrated audio de-embedder for 8 channels of 48kHz audio * Integrated audio clock generator * Ancillary data extraction * Optional conversion from SMPTE 425M Level B to Level A for 1080p 50/59.94/60 4:2:2 10-bit inputs * Parallel data bus selectable as either 20-bit or 10-bit * EQ GS2984/ GS2974 Link A GS2970 HV F/PCLK 10-bit HD-SDI GS2962/72 AES - OUT Speakers AUDIO 1/2 Comprehensive error detection and correction features DAC AUDIO 3/4 AUDIO 5/6 AUDIO 7/8 3G-SDI Output H, V, F or CEA 861 timing signals * 1.2V digital core power supply, 1.2V and 3.3V analog power supplies, and selectable 1.8V or 3.3V I/O power supply * GSPI host interface * -20C to +85C operating temperature range * Low power operation (typically 350mW) * Small 11mm x 11mm 100-ball BGA package Audio Selector Audio Clocks EQ GS2984/ GS2974 DAC GS2970 20-bit Video Processor Display CTRL/TIMECODE Application: Multi-format Downconverter 10-bit SD Bypass Memory SD/HS/3G-SDI Pb-free and RoHS compliant EQ GS2984/ GS2974 20-bit 20-bit Video Downconverter & Aspect Ratio Conversion GS2970 HV F /P CLK SD-SDI HD/SD Serializer (GS1582, GS2972) Errata Refer to Errata document entitled GS2970/GS2971 Errata for this device (document number 53092). AE S 1/ 2 AE S 3/ 4 AE S 5/ 6 AE S 7/ 8 Analog Sync AE S 1/ 2 Audio Processing & Delay AE S 3/ 4 AE S 5/ 6 AE S 7/ 8 Audio Clocks Sync Seperator GS2970 3Gb/s, HD, SD SDI Receiver Data Sheet 47478 - 4 September 2012 Link B Application: 1080p50/60 Monitor HV F/PCLK * HD-SDI GS2962/72 HV F/PCLK * * Application: Single Link (3G-SDI) to Dual Link (HD-SDI) Converter www.semtech.com GS4901 HV F / P CLK 1 of 145 Application: Multi-input Video Monitoring System 3G-SDI Input 1 3G-SDI Input 2 3G-SDI Input n 20-bit EQ GS2984/ GS2974 GS2970 Video Output HV F / P CLK Video Formatter 20-bit EQ GS2984/ GS2974 HV /DE /P CLK GS2970 HV F / P CLK Video Memory On Screen Display Generator 20-bit EQ GS2984/ GS2974 DVI/ VGA DAC GS2970 AE S BUS Audio Select Audio Processor AE S OUT 3/ 4 AE S OUT 5/ 6 AE S OUT 7/ 8 HV F /P CLK Sync Seperator GS4911 Audio Clocks Application: Multi-format Audio De-embedder Module 10-bit GS2962 SD/HD/3G-SDI P CLK SD/HD/3G-SDI EQ GS2984/ GS2974 GS2970 AUDIO 1/ 2 AUDIO 3/ 4 AUDIO 5/ 6 AUDIO 7/ 8 Audio Clocks Switch Logic & Drivers In SMPTE mode (the default operating mode), the GS2970 performs full SMPTE processing, and features a number of data integrity checks and measurement capabilities. The device also supports ancillary data extraction, and can provide entire ancillary data packets through host-accessible registers. It also provides a variety of other packet detection and error handling features. All of these processing features are optional, and may be individually enabled or disabled through register programming. HV F / P CLK AE S OUT 1/ 2 Analog Sync The device operates in one of four basic modes: SMPTE mode, DVB-ASI mode, Data-Through mode or Standby mode. AES Audio Outputs DAC Analog Audio Outputs Both SMPTE 425M Level A and Level B inputs are supported with optional conversion from Level B to Level A for 1080p 50/59.94/60 4:2:2 10-bit inputs. In DVB-ASI mode, sync word detection, alignment and 8b/10b decoding is applied to the received data stream. In Data-Through mode all forms of SMPTE and DVB-ASI processing are disabled, and the device can be used as a simple serial to parallel converter. The device can also operate in a lower power Standby mode. In this mode, no signal processing is carried out and the parallel output is held static. Application: Multi-format Digital VTR/Video Server V ideo Output 20-bit HV F /P CLK SD/HD/3G-SDI EQ GS2984/ GS2974 GS2970 Video Processor Storage: Tape/HDD/Solid State AUDIO 1/ 2 AUDIO 3/ 4 AUDIO 5/ 6 AUDIO 7/ 8 Audio Processor Audio Clocks Audio Outputs Description The GS2970 is a multi-rate SDI Receiver which includes complete SMPTE processing, as per SMPTE 425M, 292 and SMPTE 259M-C. The SMPTE processing features can be bypassed to support signals with other coding schemes. Parallel data outputs are provided in 20-bit or 10-bit format for 3Gb/s, HD and SD video rates, with a variety of mapping options. As such, this parallel bus can interface directly with video processor ICs, and output data can be multiplexed onto 10 bits for a low pin count interface. Up to eight channels (two audio groups) of serial digital audio may be extracted from the video data stream, in accordance with SMPTE 272M-C and SMPTE 299M. The output audio formats supported by the device include AES/EBU and I2S, and two other industry standard serial digital formats. A variety of audio processing features are provided to ease implementation. Audio clocks are internally generated and provided by the device. The device features an Integrated Reclocker with an internal VCO and a wide Input Jitter Tolerance (IJT) of 0.7UI. A serial digital loop-through output is provided, which can be configured to output either reclocked or non-reclocked serial digital data. The serial digital output can be connected to an external cable driver. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 2 of 145 Crystal Buffer/ Oscillator GSPI and JTAG Controller CORE_VDD CORE_GND IO_VDD IO_GND DVB_ASI RESET_TRST STANDBY IOPROC_EN/DIS SMPTE_BYPASS 20BIT/10BIT TIM861 SW_EN AUDIO_EN/DIS AOUT_1/2 AOUT_3/4 AOUT_5/6 AOUT_7/8 ACLK AMCLK WCLK SDIN_TDI SCLK_TCLK CS_TMS SDOUT_TDO JTAG/HOST XTAL_OUT XTAL1 XTAL2 VCO_VDD VCO_GND PLL_VDD PLL_GND BUFF_VDD BUFF_GND Functional Block Diagram Host Interface VBG LB_CONT LF SDI TERM Buffer SDI Reclocker with Integrated VCO Serial to Parallel Converter Descramble, Word Align, Rate Detect Video Standard Detect TRS Detect Timing Extraction Audio DeEmbedder, Audio Clock Generation ANC/ Checksum /352M Extraction SMPTE 425M Level B Level A 1080p 50/60 4:2:2 10-bit Illegal code remap, TRS/ Line Number/ CRS Insertion, EDH Packet Insertion PCLK DOUT[19:0] LOCKED F/De V/VSync H/HSync Error Flags Mux YANC/CANC Buffer Rate_det[1:0] DVB-ASI Decoder SDO Output Mux/ Demux Mux SDO STAT[5:0] SDI_VDD SDI_GND A_VDD A_GND RC_BYP SDO_EN/DIS I/O Crosspoint GS2970 Functional Block Diagram Revision History Version ECR PCN Date 4 158468 - September 2012 Changes throughout the document. 3 153143 53865 November 2009 Added reference to GS2970/GS2971 Errata (document number 53092). 2 151817 - June 2009 1 150800 - December 2008 0 150716 - October 2008 Converted to Preliminary Data Sheet. D 149446 - August 2008 Updated document with new format. Changed programming table for STAT2_CONFIG register (bits 14-10 in register 008h) in Table 4-29: Video Core Configuration and Status Registers. Added Table 4-3: Input Clock Requirements. Added Figure 4-3: 27MHz Clock Sources. Changed SCLK period in Table 4-28. Removed Flywheel references from the Block Diagram and TAC. C 148809 - January 2008 Updates to all sections. B 148768 - December 2007 Updates and revised 5.1 Typical Application Circuit. A 147986 - December 2007 New Document. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Changes and/or Modifications Corrections to Timing Diagrams in Figure 4-4, Figure 4-5 and Figure 4-6. Clarification to Section 4.18.8. Updates to all sections. Converted to Data Sheet. Updates to all sections. 3 of 145 Contents Key Features ........................................................................................................................................................1 Errata......................................................................................................................................................................1 Applications.........................................................................................................................................................1 Description...........................................................................................................................................................2 Functional Block Diagram ..............................................................................................................................3 Revision History .................................................................................................................................................3 1. Pin Out...............................................................................................................................................................9 1.1 Pin Assignment ..................................................................................................................................9 1.2 Pin Descriptions ................................................................................................................................9 2. Electrical Characteristics ......................................................................................................................... 16 2.1 Absolute Maximum Ratings ....................................................................................................... 16 2.2 Recommended Operating Conditions .................................................................................... 16 2.3 DC Electrical Characteristics ..................................................................................................... 17 2.4 AC Electrical Characteristics ..................................................................................................... 19 3. Input/Output Circuits ............................................................................................................................... 25 4. Detailed Description.................................................................................................................................. 28 4.1 Functional Overview .................................................................................................................... 28 4.2 SMPTE 425M Mapping - 3G Level A and Level B Formats ............................................... 28 4.2.1 Level A Mapping................................................................................................................ 28 4.2.2 Level B Mapping ................................................................................................................ 29 4.3 Serial Digital Input ........................................................................................................................ 29 4.4 Serial Digital Loop-Through Output ........................................................................................ 29 4.5 Serial Digital Reclocker ............................................................................................................... 30 4.5.1 PLL Loop Bandwidth ........................................................................................................ 30 4.6 External Crystal/Reference Clock ........................................................................................... 31 4.7 Lock Detect ...................................................................................................................................... 33 4.7.1 Asynchronous Lock .......................................................................................................... 33 4.7.2 Signal Interruption............................................................................................................ 34 4.8 SMPTE Functionality .................................................................................................................... 34 4.8.1 Descrambling and Word Alignment ........................................................................... 34 4.9 Parallel Data Outputs ................................................................................................................... 34 4.9.1 Parallel Data Bus Buffers................................................................................................. 34 4.9.2 Parallel Output in SMPTE Mode ................................................................................... 38 4.9.3 Parallel Output in DVB-ASI Mode ............................................................................... 38 4.9.4 Parallel Output in Data-Through Mode ..................................................................... 39 4.9.5 Parallel Output Clock (PCLK)......................................................................................... 39 4.9.6 DDR Parallel Clock Timing ............................................................................................. 40 4.10 Timing Signal Generator ........................................................................................................... 41 4.10.1 Manual Switch Line Lock Handling.......................................................................... 42 4.10.2 Automatic Switch Line Lock Handling .................................................................... 43 4.10.3 Switch Line Lock Handling During Level B to Level A Conversion ............... 44 4.11 Programmable Multi-function Outputs ............................................................................... 46 4.12 H:V:F Timing Signal Generation ............................................................................................ 47 4.12.1 CEA-861 Timing Generation ....................................................................................... 48 4.13 Automatic Video Standards Detection ................................................................................ 56 4.14 Data Format Detection & Indication ..................................................................................... 59 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 4 of 145 4.15 EDH Detection .............................................................................................................................. 60 4.15.1 EDH Packet Detection.................................................................................................... 60 4.15.2 EDH Flag Detection ........................................................................................................ 60 4.16 Video Signal Error Detection & Indication .......................................................................... 61 4.16.1 TRS Error Detection ........................................................................................................ 63 4.16.2 Line Based CRC Error Detection................................................................................. 63 4.16.3 EDH CRC Error Detection............................................................................................. 64 4.16.4 HD & 3G Line Number Error Detection.................................................................... 64 4.17 Ancillary Data Detection & Indication ................................................................................. 64 4.17.1 Programmable Ancillary Data Detection ................................................................ 66 4.17.2 SMPTE 352M Payload Identifier................................................................................. 67 4.17.3 Ancillary Data Checksum Error ................................................................................. 68 4.17.4 Video Standard Error ..................................................................................................... 69 4.18 Signal Processing ......................................................................................................................... 69 4.18.1 TRS Correction & Insertion........................................................................................... 70 4.18.2 Line Based CRC Correction & Insertion ................................................................... 71 4.18.3 Line Number Error Correction & Insertion ............................................................. 71 4.18.4 ANC Data Checksum Error Correction & Insertion ............................................. 71 4.18.5 EDH CRC Correction & Insertion ............................................................................... 71 4.18.6 Illegal Word Re-mapping ............................................................................................. 72 4.18.7 TRS and Ancillary Data Preamble Remapping...................................................... 72 4.18.8 Ancillary Data Extraction............................................................................................. 72 4.18.9 Level B to Level A Conversion .................................................................................... 76 4.19 Audio De-embedder ................................................................................................................... 77 4.19.1 Serial Audio Data I/O Signals...................................................................................... 77 4.19.2 Serial Audio Data Format Support ............................................................................ 79 4.19.3 Audio Processing............................................................................................................. 83 4.19.4 Error Reporting ................................................................................................................ 89 4.20 GSPI - HOST Interface ................................................................................................................ 90 4.20.1 Command Word Description ...................................................................................... 90 4.20.2 Data Read or Write Access........................................................................................... 91 4.20.3 GSPI Timing....................................................................................................................... 92 4.21 Host Interface Register Maps .................................................................................................. 94 4.21.1 Video Core Registers ...................................................................................................... 94 4.21.2 SD Audio Core Registers .............................................................................................107 4.21.3 HD and 3G Audio Core Registers.............................................................................122 4.22 JTAG Test Operation .................................................................................................................137 4.23 Device Power-up .......................................................................................................................139 4.24 Device Reset ................................................................................................................................139 4.25 Standby Mode .............................................................................................................................139 5. Application Reference Design..............................................................................................................140 5.1 Typical Application Circuit ......................................................................................................140 6. References & Relevant Standards .......................................................................................................141 7. Package & Ordering Information ........................................................................................................142 7.1 Package Dimensions ...................................................................................................................142 7.2 Packaging Data .............................................................................................................................143 7.3 Marking Diagram .........................................................................................................................143 7.4 Solder Reflow Profiles ................................................................................................................144 7.5 Ordering Information .................................................................................................................144 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 5 of 145 List of Figures Figure 3-1: Digital Input Pin with Schmitt Trigger............................................................................... 25 Figure 3-2: Bidirectional Digital Input/Output Pin.............................................................................. 25 Figure 3-3: Bidirectional Digital Input/Output Pin with programmable drive strength......... 26 Figure 3-4: XTAL1/XTAL2/XTAL-OUT ................................................................................................... 26 Figure 3-5: VBG .............................................................................................................................................. 26 Figure 3-6: LB_CONT .................................................................................................................................... 27 Figure 3-7: Loop Filter .................................................................................................................................. 27 Figure 3-8: SDI/SDI and TERM .................................................................................................................. 27 Figure 3-9: SDO/SDO .................................................................................................................................... 27 Figure 4-1: Level A Mapping ...................................................................................................................... 28 Figure 4-2: Level B Mapping ...................................................................................................................... 29 Figure 4-3: 27MHz Clock Sources ............................................................................................................ 32 Figure 4-4: PCLK to Data and Control Signal Output Timing - SDR Mode 1 .............................. 35 Figure 4-5: PCLK to Data and Control Signal Output Timing - SDR Mode 2 .............................. 36 Figure 4-6: PCLK to Data and Control Signal Output Timing - DDR Mode ................................. 37 Figure 4-7: DDR Video Interface .............................................................................................................. 40 Figure 4-8: Delay Adjustment Ranges .................................................................................................... 41 Figure 4-9: Switch Line Locking on a Non-Standard Switch Line ................................................. 43 Figure 4-10: H:V:F Output Timing - 3G Level A and HDTV 20-bit Mode .................................... 47 Figure 4-11: H:V:F Output Timing - 3G Level A and HDTV 10-bit Mode 3G Level B 20-bit Mode, each 10-bit stream ......................................................................................... 47 Figure 4-12: H:V:F Output Timing - 3G Level B 10-bit Mode .......................................................... 47 Figure 4-13: H:V:F Output Timing - HD 20-bit Output Mode ......................................................... 48 Figure 4-14: H:V:F Output Timing - HD 10-bit Output Mode ......................................................... 48 Figure 4-15: H:V:F Output Timing - SD 20-bit Output Mode .......................................................... 48 Figure 4-16: H:V:F Output Timing - SD 10-bit Output Mode .......................................................... 48 Figure 4-17: H:V:DE Output Timing 1280 x 720p @ 59.94/60 (Format 4) ................................... 50 Figure 4-18: H:V:DE Output Timing 1920 x 1080i @ 59.94/60 (Format 5) ................................. 51 Figure 4-19: H:V:DE Output Timing 720 (1440) x 480i @ 59.94/60 (Format 6&7) .................... 52 Figure 4-20: H:V:DE Output Timing 1280 x 720p @ 50 (Format 19) ............................................. 52 Figure 4-21: H:V:DE Output Timing 1920 x 1080i @ 50 (Format 20) ........................................... 53 Figure 4-22: H:V:DE Output Timing 720 (1440) x 576 @ 50 (Format 21 & 22) ........................... 54 Figure 4-23: H:V:DE Output Timing 1920 x 1080p @ 59.94/60 (Format 16) .............................. 54 Figure 4-24: H:V:DE Output Timing 1920 x 1080p @ 50 (Format 31) .......................................... 55 Figure 4-25: H:V:DE Output Timing 1920 x 1080p @ 23.94/24 (Format 32) .............................. 55 Figure 4-26: H:V:DE Output Timing 1920 x 1080p @ 25 (Format 33) .......................................... 56 Figure 4-27: H:V:DE Output Timing 1920 x 1080p @ 29.97/30 (Format 34) .............................. 56 Figure 4-28: Y/1ANC and C/2ANC Signal Timing .............................................................................. 66 Figure 4-29: Ancillary Data Extraction - Step A .................................................................................. 73 Figure 4-30: Ancillary Data Extraction - Step B ................................................................................... 74 Figure 4-31: Ancillary Data Extraction - Step C .................................................................................. 74 Figure 4-32: Ancillary Data Extraction - Step D .................................................................................. 75 Figure 4-33: ACLK to Data Signal Output Timing ............................................................................... 78 Figure 4-34: I2S Audio Output Format .................................................................................................... 79 Figure 4-35: AES/EBU Audio Output Format ....................................................................................... 79 Figure 4-36: Serial Audio, Left Justified, MSB First ............................................................................. 80 Figure 4-37: Serial Audio, Left Justified, LSB First .............................................................................. 80 Figure 4-38: Serial Audio, Right Justified, MSB First .......................................................................... 80 Figure 4-39: Serial Audio, Right Justified, LSB First ........................................................................... 80 Figure 4-40: AES/EBU Audio Output to Bit Clock Timing ................................................................ 80 Figure 4-41: ECC 24-bit Array and Examples ...................................................................................... 83 Figure 4-42: Sample Distribution over 5 Video Frames (525-line Systems) ............................... 84 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 6 of 145 Figure 4-43: Audio Buffer After Initial 26 Sample Write .................................................................. 85 Figure 4-44: Audio Buffer Pointer Boundary Checking .................................................................... 85 Figure 4-45: GSPI Application Interface Connection ........................................................................ 90 Figure 4-46: Command Word Format ..................................................................................................... 90 Figure 4-47: Data Word Format ................................................................................................................ 91 Figure 4-48: Write Mode .............................................................................................................................. 92 Figure 4-49: Read Mode ............................................................................................................................... 92 Figure 4-50: GSPI Time Delay .................................................................................................................... 92 Figure 4-51: In-Circuit JTAG .................................................................................................................... 138 Figure 4-52: System JTAG ......................................................................................................................... 138 Figure 4-53: Reset Pulse ............................................................................................................................. 139 Figure 7-1: Pb-free Solder reflow Profile ............................................................................................. 144 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 7 of 145 List of Tables Table 1-1: Pin Descriptions ............................................................................................................................ 9 Table 2-1: Absolute Maximum Ratings................................................................................................... 16 Table 2-2: Recommended Operating Conditions................................................................................ 16 Table 2-3: DC Electrical Characteristics ................................................................................................. 17 Table 2-4: AC Electrical Characteristics ................................................................................................. 19 Table 4-1: Serial Digital Output................................................................................................................. 30 Table 4-2: PLL Loop Bandwidth ................................................................................................................ 31 Table 4-3: Input Clock Requirements...................................................................................................... 32 Table 4-4: Lock Detect Conditions............................................................................................................ 33 Table 4-5: GS2970 Output Video Data Format Selections................................................................ 37 Table 4-6: GS2970 PCLK Output Rates ................................................................................................... 39 Table 4-7: Switch Line Position for Digital Systems ........................................................................... 44 Table 4-8: Output Signals Available on Programmable Multi-Function Pins............................ 46 Table 4-9: Supported CEA-861 Formats................................................................................................. 49 Table 4-10: CEA861 Timing Formats....................................................................................................... 49 Table 4-11: Supported Video Standard Codes ..................................................................................... 57 Table 4-12: Data Format Register Codes ................................................................................................ 59 Table 4-13: Error Status Register and Error Mask Register .............................................................. 62 Table 4-14: SMPTE 352M Packet Data .................................................................................................... 68 Table 4-15: IOPROC_DISABLE Register Bits ......................................................................................... 70 Table 4-16: Serial Audio Pin Descriptions ............................................................................................. 77 Table 4-17: Audio Output Formats........................................................................................................... 79 Table 4-18: Audio Data Packet Detect Register ................................................................................... 81 Table 4-19: Audio Group DID Host Interface Settings....................................................................... 82 Table 4-20: Audio Data and Control Packet DID Setting Register................................................. 82 Table 4-21: Audio Buffer Pointer Offset Settings ................................................................................ 86 Table 4-22: Audio Channel Mapping Codes ......................................................................................... 86 Table 4-23: Audio Sample Word Lengths .............................................................................................. 87 Table 4-24: Audio Channel Status Information Registers ................................................................ 88 Table 4-25: Audio Channel Status Block for Regenerate Mode Default Settings ..................... 88 Table 4-26: Audio Mute Control Bits ....................................................................................................... 89 Table 4-27: GSPI Time Delay...................................................................................................................... 92 Table 4-28: GSPI Timing Parameters (50% levels; 3.3V or 1.8V operation) ................................ 93 Table 4-29: Video Core Configuration and Status Registers............................................................ 94 Table 4-30: SD Audio Core Configuration and Status Registers................................................... 107 Table 4-31: HD and 3G Audio Core Configuration and Status Registers .................................. 122 Table 4-32: ANC Extraction FIFO Access Registers.......................................................................... 137 Table 7-1: Packaging Data......................................................................................................................... 143 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 8 of 145 1. Pin Out 1.1 Pin Assignment 1 2 A VBG LF B A_VDD C D E 3 4 5 6 7 8 LB_CONT VCO_ VDD STAT0 STAT1 IO_VDD PCLK DOUT18 DOUT17 PLL_ VDD RSV VCO_ GND STAT2 STAT3 IO_GND DOUT19 DOUT16 DOUT15 SDI A_GND PLL_ VDD PLL_ VDD STAT4 STAT5 RESET _TRST SDI A_GND A_GND PLL_ GND CORE _GND CORE _VDD SW_EN JTAG/ HOST IO_GND SDI_VDD SDI_GND A_GND PLL_ GND CORE _GND CORE _VDD SDOUT_ TDO SDIN_ TDI DOUT10 DOUT11 CS_ TMS SCLK_ TCK DOUT8 9 10 DOUT12 DOUT14 DOUT13 IO_VDD F TERM RSV A_GND PLL_ GND CORE _GND CORE _VDD G RSV RSV RC_BYP RSV CORE _GND CORE _VDD H BUFF_ VDD BUFF_ GND AUDIO_ EN/DIS WCLK TIM_861 XTAL_ OUT 20bit/ 10bit IOPROC_ EN/DIS DOUT6 DOUT7 J SDO SDO_ EN/DIS AOUT_1/2 ACLK AOUT_5/6 XTAL2 IO_GND DOUT1 DOUT4 DOUT5 K SDO AOUT_7/8 XTAL1 IO_VDD DOUT0 DOUT2 DOUT3 STANDBY AOUT_3/4 AMCLK SMPTE_ DVB_ASI IO_GND BYPASS DOUT9 IO_VDD 1.2 Pin Descriptions Table 1-1: Pin Descriptions Pin Number Name Timing Type A1 VBG Analog Input Band Gap voltage filter connection. A2 LF Analog Input Loop Filter component connection. A3 LB_CONT Analog Input Connection for loop bandwidth control resistor. A4 VCO_VDD Input Power POWER pin for the VCO. Connect to 1.2V5% analog supply followed by a RC filter (see 5. Application Reference Design). A 105 1% resistor must be used in the RC filter circuit. VCO_VDD is nominally 0.7V. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Description 9 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name A5, A6, B5, B6, C5, C6 STAT[0:5] Timing Type Output Description MULTI-FUNCTIONAL OUTPUT PORT. Please refer to the Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Each of the STAT [0:5] pins can be configured individually to output one of the following signals: Signal H/HSYNC V/VSYNC F/DE LOCKED Y/1ANC C/2ANC DATA ERROR VIDEO ERROR AUDIO ERROR EDH DETECTED CARRIER DETECT RATE_DET0 RATE_DET1 A7, D10, G10, K7 IO_VDD Input Power A8 PCLK Output Default STAT0 STAT1 STAT2 STAT3 STAT4 - STAT5 - - - - - - POWER connection for digital I/O. Connect to 3.3V or 1.8V DC digital. PARALLEL DATA BUS CLOCK Please refer to the Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 3G 10-bit or 20-bit mode PCLK @ 148.5 or 148.5/1.001MHz HD 10-bit mode PCLK @ 148.5 or 148.5/1.001MHz HD 20-bit mode PCLK @ 74.25 or 74.25/1.001MHz SD 10-bit mode PCLK @ 27MHz SD 20-bit mode PCLK @ 13.5MHz 10 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name A9, A10, B8, B9, B10,C8, C9, C10, E9, E10 DOUT18, 17, 19, 16, 15, 12, 14, 13, 10, 11 Timing Type Output Description PARALLEL DATA BUS Please refer to the Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. 20-bit mode 20bit/10bit = HIGH SMPTE mode (SMPTE_BYPASS = HIGH and DVB_ASI = LOW): Luma data output for SD and HD data rates; Data Stream 1 for 3G data rate DVB-ASI mode (SMPTE_BYPASS = LOW and DVB_ASI = HIGH): Not defined Data-Through mode (SMPTE_BYPASS = LOW and DVB_ASI = LOW): Data output 10-bit mode 20bit/10bit = LOW SMPTE mode (SMPTE_BYPASS = HIGH and DVB_ASI = LOW): Multiplexed Luma/Chroma data output for SD and HD data rates; Multiplexed Data Stream 1&2 for 3G data rate DVB-ASI mode (SMPTE_BYPASS = LOW and DVB_ASI = HIGH): 8b/10b decoded DVB-ASI data Data-Through mode (SMPTE_BYPASS = LOW and DVB_ASI = LOW): Data output B1 A_VDD Input Power POWER pin for analog circuitry. Connect to 3.3V DC analog. B2, C3, C4 PLL_VDD Input Power POWER pins for the Reclocker PLL. Connect to 1.2V DC analog. B3, F2, G1, G2, G4 RSV B4 VCO_GND Input Power GND pin for the VCO. Connect to analog GND. B7, D9, G9, J7 IO_GND Input Power GND connection for digital I/O. Connect to digital GND. C1, D1 SDI, SDI Analog Input Serial Digital Differential Input. C2, D2, D3, E3, F3 A_GND Input Power GND pins for sensitive analog circuitry. Connect to analog GND. These pins must be left unconnected. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 11 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name C7 RESET_TRST Timing Type Description Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to reset the internal operating conditions to default settings and to reset the JTAG sequence. Normal mode (JTAG/HOST = LOW): When LOW, all functional blocks are set to default conditions and all digital output signals become high impedance. When HIGH, normal operation of the device resumes. JTAG test mode (JTAG/HOST = HIGH): When LOW, all functional blocks are set to default and the JTAG test sequence is reset. When HIGH, normal operation of the JTAG test sequence resumes after RESET_TRST is de-asserted. D4, E4, F4 PLL_GND Input Power GND pins for the Reclocker PLL. Connect to analog GND. D5, E5, F5, G5 CORE_GND Input Power GND connection for device core. Connect to digital GND. D6, E6, F6, G6 CORE_VDD Input Power POWER connection for device core. Connect to 1.2V DC digital. D7 SW_EN Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to enable switch-line locking, as described in Section 4.10.1. D8 JTAG/HOST Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to select JTAG test mode or host interface mode. When JTAG/HOST is HIGH, the host interface port is configured for JTAG test. When JTAG/HOST is LOW, normal operation of the host interface port resumes. E1 SDI_VDD Input Power POWER pin for SDI buffer. Connect to 3.3V DC analog. E2 SDI_GND Input Power GND pin for SDI buffer. Connect to analog GND. E7 SDOUT_TDO Output COMMUNICATION SIGNAL OUTPUT Please refer to the Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. GSPI serial data output/test data out. In JTAG mode (JTAG/HOST = HIGH), this pin is used to shift test results from the device. In host interface mode, this pin is used to read status and configuration data from the device. Note: GSPI is slightly different than the SPI. For more details on GSPI, please refer to 4.20 GSPI - HOST Interface. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 12 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name E8 SDIN_TDI Timing Type Description Input COMMUNICATION SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. GSPI serial data in/test data in. In JTAG mode (JTAG/HOST = HIGH), this pin is used to shift test data into the device. In host interface mode, this pin is used to write address and configuration data words into the device. F1 TERM Analog Input F7 CS_TMS Input Decoupling for internal SDI termination resistors. COMMUNICATION SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Chip select / test mode start. In JTAG mode (JTAG/HOST = HIGH), this pin is Test Mode Start, used to control the operation of the JTAG test. In host interface mode (JTAG/HOST = LOW), this pin operates as the host interface chip select and is active LOW. F8 SCLK_TCK Input COMMUNICATION SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Serial data clock signal. In JTAG mode (JTAG/HOST = HIGH), this pin is the JTAG clock. In host interface mode (JTAG/HOST = LOW), this pin is the host interface serial bit clock. All JTAG/host interface addresses and data are shifted into/out of the device synchronously with this clock. F9, F10, H9, H10, J8, J9, J10, K8, K9, K10 DOUT8, 9, 6, 7, 1, 4, 5, 0, 2, 3 Output PARALLEL DATA BUS Please refer to the Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. 20-bit mode 20bit/10bit = HIGH SMPTE mode (SMPTE_BYPASS = HIGH and DVB_ASI = LOW): Chroma data output for SD and HD data rates; Data Stream 2 for 3G data rate DVB-ASI mode (SMPTE_BYPASS = LOW and DVB_ASI = HIGH): Not defined Data-Through mode (SMPTE_BYPASS = LOW and DVB_ASI = LOW): Data output 10-bit mode 20bit/10bit = LOW G3 RC_BYP Input Forced LOW CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. When this pin is LOW, the serial digital output is the buffered version of the input serial data. When this pin is HIGH, the serial digital output is the reclocked version of the input serial data. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 13 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name G7 SMPTE_BYPASS Timing Type Input/Output Description CONTROL SIGNAL INPUT/OUTPUT Please refer to the Input/Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Indicates the presence of valid SMPTE data. When the AUTO/MAN bit in the host interface register is HIGH (Default), this pin is an OUTPUT. SMPTE_BYPASS is HIGH when the device locks to a SMPTE compliant input. SMPTE_BYPASS is LOW under all other conditions. When the AUTO/MAN bit in the host interface register is LOW, this pin is an INPUT: No SMPTE scrambling takes place, and none of the I/O processing features of the device are available when SMPTE_BYPASS is set LOW. When SMPTE_BYPASS is set HIGH, the device carries out SMPTE scrambling and I/O processing. When SMPTE_BYPASS and DVB_ASI are both set LOW, the device operates in Data-Through mode. G8 DVB_ASI Input/Output CONTROL SIGNAL INPUT Please refer to the Input/Output Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to enable/disable DVB-ASI data extraction in manual mode. When the AUTO/MAN bit in the host interface is LOW, this pin is an input and when the DVB_ASI pin is set HIGH the device will carry out DVB_ASI data extraction and processing. The SMPTE_BYPASS pin must be set LOW. When SMPTE_BYPASS and DVB_ASI are both set LOW, the device operates in Data-Through mode. When the AUTO/MAN bit in the host interface is HIGH (default), DVB-ASI is configured as a status output (set LOW), and DVB-ASI input streams are not supported or recognized. H1 BUFF_VDD Input Power POWER pin for the serial digital output 50 buffer. Connect to 3.3V DC analog. H2 BUFF_GND Input Power GND pin for the cable driver buffer. Connect to analog GND. H3 AUDIO_EN/DIS Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Enables or disables audio extraction. H4 WCLK Output H5 TIM_861 Input 48kHz word clock for Audio. CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to select CEA-861 timing mode. When TIM_861 is HIGH, the device outputs CEA 861 timing signals (HSYNC/VSYNC/DE) instead of H:V:F digital timing signals. H6 XTAL_OUT GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Digital Output Buffered 27MHz crystal output. Can be used to cascade the crystal signal. 14 of 145 Table 1-1: Pin Descriptions (Continued) Pin Number Name H7 20bit/10bit Timing Type Description Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to select the output bus width. HIGH = 20-bit, LOW = 10-bit. H8 IOPROC_EN/DIS Input CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to enable or disable audio and video processing features. When IOPROC_EN is HIGH, the audio and video processing features of the device are enabled. When IOPROC_EN is LOW, the processing features of the device are disabled, and the device is in a low-latency operating mode. J1, K1 SDO, SDO Output Serial Data Output Signal. 50 CML buffer for interfacing to an external cable driver. Serial digital output signal operating at 2.97Gb/s, 2.97/1.001Gb/s, 1.485Gb/s, 1.485/1.001Gb/s and 270Mb/s. J2 Input SDO_EN/DIS CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. Used to enable/disable the serial digital output stage. When SDO_EN/DIS is LOW, the serial digital output signals, SDO and SDO, are both pulled HIGH. When SDO_EN/DIS is HIGH, the serial digital output signals, SDO and SDO, are enabled. J3 AOUT_1/2 Output Serial Audio Output; Channels 1 and 2. J4 ACLK Output 64fs sample clock for audio. J5 AOUT_5/6 Output Serial Audio Output; Channels 5 and 6. J6, K6 XTAL2, XTAL1 Analog Input K2 STANDBY Input Input connection for 27MHz crystal. CONTROL SIGNAL INPUT Please refer to the Input Logic parameters in the DC Electrical Characteristics table for logic level threshold and compatibility. When this pin is set HIGH, the device is placed in a power-saving mode. No data processing occurs, and the digital I/Os are powered down. In this mode, the serial digital output signals, SDO and SDO, are both pulled HIGH. K3 AOUT_3/4 Output Serial Audio Output; Channels 3 and 4. K4 AMCLK Output Oversampled master clock for audio (128fs, 256fs, 512fs selectable). K5 AOUT_7/8 Output Serial Audio Output; Channels 7 and 8. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 15 of 145 2. Electrical Characteristics 2.1 Absolute Maximum Ratings Table 2-1: Absolute Maximum Ratings Parameter Value/Units Supply Voltage, Digital Core (CORE_VDD) -0.3V to +1.5V Supply Voltage, Digital I/O (IO_VDD) -0.3V to +4.0V Supply Voltage, Analog 1.2V (PD_VDD, VCO_VDD) -0.3V to +1.5V Supply Voltage, Analog 3.3V (SDI_VDD, BUFF_VDD, A_VDD) -0.3V to +4.0V Input Voltage Range (digital inputs) -2.0V to +5.25V Ambient Operating Temperature (TA) -40C < TA < 95C Storage Temperature (TSTG) -40C < TSTG < 125C Peak Reflow Temperature (JEDEC J-STD-020C) 260C ESD Sensitivity, HBM (JESD22-A114) 2kV NOTES: Absolute Maximum Ratings are those values beyond which damage may occur. Functional operation under these conditions or at any other condition beyond those indicated in the AC/DC Electrical Characteristics sections is not implied. 2.2 Recommended Operating Conditions Table 2-2: Recommended Operating Conditions Parameter Operating Temperature Range, Ambient Supply Voltage, Digital Core Supply Voltage, Digital I/O Symbol Conditions Min Typ Max Units Notes TA - -20 - 85 C - CORE_VDD - 1.14 1.2 1.26 V - 1.8V mode 1.71 1.8 1.89 V - 3.3V mode 3.13 3.3 3.47 V - IO_VDD Supply Voltage, PLL PLL_VDD - 1.14 1.2 1.26 V - Supply Voltage, VCO VCO_VDD - - 0.7 - V 1 A_VDD - 3.13 3.3 3.47 V 2 SDI_VDD - 3.13 3.3 3.47 V 2 BUFF_VDD - 3.13 3.3 3.47 V 2 Supply Voltage, Analog Supply Voltage, Serial Digital Input Supply Voltage, CD Buffer NOTES 1. This is 0.7V rather than 1.2V because there is a voltage drop across an external 105 resistor. See Typical Application Circuit on page 140. 2. The 3.3V supplies must track the 3.3V supply of an external EQ and external CD. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 16 of 145 2.3 DC Electrical Characteristics Table 2-3: DC Electrical Characteristics Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Conditions Min Typ Max Units Notes I1V2 10bit 3G - 220 265 mA - 20bit 3G - 215 265 mA - 10/20bit HD - 175 215 mA - 10/20bit SD - 145 180 mA - DVB_ASI - 135 165 mA - 10bit 3G - 32 34 mA - 20bit 3G - 32 34 mA - 10/20bit HD - 20 21 mA - 10/20bit SD - 6 7 mA - DVB_ASI - 6 7 mA - 10bit 3G - 95 105 mA - 20bit 3G - 95 105 mA - 10/20bit HD - 65 75 mA - 10/20bit SD - 35 45 mA - DVB_ASI - 35 45 mA - 10bit 3G - 380 470 mW - 20bit 3G - 350 435 mW - 10/20bit HD - 300 360 mW - 10/20bit SD - 235 305 mW - DVB_ASI - 235 305 mW - Reset - 200 - mW - Standby - 16 44 mW - 10bit 3G - 580 700 mW - 20bit 3G - 580 695 mW - 10/20bit HD - 430 530 mW - 10/20bit SD - 290 370 mW - DVB_ASI - 290 370 mW - Reset - 220 - mW - Standby - 16 44 mW - System +1.2V Supply Current +1.8V Supply Current +3.3V Supply Current Total Device Power (IO_VDD = 1.8V) Total Device Power (IO_VDD = 3.3V) I1V8 I3V3 P1D8 P3D3 Digital I/O Input Logic LOW VIL 3.3V or 1.8V operation IO_VSS -0.3 - 0.3 x IO_VDD V - Input Logic HIGH VIH 3.3V or 1.8V operation 0.7 x IO_VDD - IO_VDD +0.3 V - GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 17 of 145 Table 2-3: DC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Output Logic LOW VOL Output Logic HIGH VOH Conditions Min Typ Max Units Notes IOL = 5mA, 1.8V operation - - 0.2 V - IOL = 8mA, 3.3V operation - - 0.4 V - IOH = 5mA, 1.8V operation 1.4 - - V - IOH = 8mA, 3.3V operation 2.4 - - V - - 50 load 2.5 SDI_VDD -(0.75/2) SDI_VDD -(0.55/2) V - - 50 load BUFF_VDD -(0.6/2) BUFF_VDD -(0.45/2) BUFF_VDD -(0.35/2) V - Serial Input Serial Input Common Mode Voltage Serial Output Serial Output Common Mode Voltage Notes: The output drive strength of the digital outputs can be programmed through the host interface. please see Table 4-29: Video Core Configuration and Status Registers, register 06Dh for details. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 18 of 145 2.4 AC Electrical Characteristics Table 2-4: AC Electrical Characteristics Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Conditions Min Typ Max Units Notes 3G (Level A) 80 - 83 PCLK - 3G (Level B) 143 - 151 PCLK - HD 80 - 83 PCLK - SD 50 - 55 PCLK - 3G (Level A) 44 - 48 PCLK - 3G (Level B) 108 - 116 PCLK - HD 44 - 48 PCLK - SD 44 - 48 PCLK - 3G (Level A) 33 - 36 PCLK - HD 33 - 36 PCLK - SD 32 - 35 PCLK - 3G (Level A) 6 - 9 PCLK - HD 6 - 9 PCLK - SD 5 - 9 PCLK - - SD 12 - 16 PCLK - treset - 1 - - ms - System Device Latency: AUDIO_EN = 1, SMPTE mode, - IOPROC_EN = 1 Device Latency: AUDIO_EN = 0, SMPTE mode, - IOPROC_EN = 1 Device Latency: AUDIO_EN = 0, SMPTE mode, IOPROC_EN = 0 - Device Latency: AUDIO_EN = 0, SMPTE bypass, IOPROC_EN = 0 Device Latency: DVB-ASI Reset Pulse Width - Parallel Output Parallel Clock Frequency fPCLK - 13.5 - 148.5 MHz - Parallel Clock Duty Cycle DCPCLK - 40 - 60 % - GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 19 of 145 Table 2-4: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Output Data Hold Time (1.8V) Output Data Hold Time (3.3V) Symbol toh toh GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Conditions Min Typ Max Units Notes SPI 1.5 - - ns 1 AUDIO 1.5 - - ns 1 DBUS 0.4 - - ns 1 STAT 0.45 - - ns 1 3G 20-bit 6pF Cload DBUS 1.0 - - ns 1 STAT 1.0 - - ns 1 HD 10-bit 6pF Cload DBUS 1.0 - - ns 1 STAT 1.0 - - ns 1 HD 20-bit 6pF Cload DBUS 1.0 - - ns 1 STAT 1.0 - - ns 1 SD 10-bit 6pF Cload DBUS 19.4 - - ns 1 STAT 19.4 - - ns 1 SD 20-bit 6pF Cload DBUS 38.0 - - ns 1 STAT 38.0 - - ns 1 3G 10-bit 6pF Cload SPI 1.5 - - ns 2 AUDIO 1.5 - - ns 2 DBUS 0.45 - - ns 2 STAT 0.45 - - ns 2 3G 20-bit 6pF Cload DBUS 1.0 - - ns 2 STAT 1.0 - - ns 2 HD 10-bit 6pF Cload DBUS 1.0 - - ns 2 STAT 1.0 - - ns 2 HD 20-bit 6pF Cload DBUS 1.0 - - ns 2 STAT 1.0 - - ns 2 SD 10-bit 6pF Cload DBUS 19.4 - - ns 2 STAT 19.4 - - ns 2 SD 20-bit 6pF Cload DBUS 38.0 - - ns 2 STAT 38.0 - - ns 2 3G 10-bit 6pF Cload 20 of 145 Table 2-4: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Output Data Delay Time (1.8V) Output Data Delay Time (3.3V) tod tod GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Conditions Min Typ Max Units Notes SPI - - 14.0 ns 3 AUDIO - - 7.0 ns 3 DBUS - - 1.8 ns 3 STAT - - 2.5 ns 3 3G 20-bit 15pF Cload DBUS - - 3.7 ns 3 STAT - - 4.4 ns 3 HD 10-bit 15pF Cload DBUS - - 3.7 ns 3 STAT - - 4.4 ns 3 HD 20-bit 15pF Cload DBUS - - 3.7 ns 3 STAT - - 4.4 ns 3 SD 10-bit 15pF Cload DBUS - - 22.2 ns 3 STAT - - 22.2 ns 3 SD 20-bit 15pF Cload DBUS - - 41.0 ns 3 STAT - - 41.0 ns 3 3G 10-bit 15pF Cload SPI - - 14.0 ns 4 AUDIO - - 7.0 ns 4 DBUS - - 1.9 ns 4 STAT - - 2.2 ns 4 3G 20-bit 15pF Cload DBUS - - 3.7 ns 4 STAT - - 4.1 ns 4 HD 10-bit 15pF Cload DBUS - - 3.7 ns 4 STAT - - 4.1 ns 4 HD 20-bit 15pF Cload DBUS - - 3.7 ns 4 STAT - - 4.1 ns 4 SD 10-bit 15pF Cload DBUS - - 22.2 ns 4 STAT - - 22.2 ns 4 SD 20-bit 15pF Cload DBUS - - 41.0 ns 4 STAT - - 41.0 ns 4 3G 10-bit 15pF Cload 21 of 145 Table 2-4: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Output Data Rise/Fall Time (1.8V) Conditions tr/tf 3G 10-bit 6pF Cload All other modes 6pF Cload 3G 10-bit 15pF Cload All other modes 15pF Cload Output Data Rise/Fall Time (3.3V) tr/tf 3G 10-bit 6pF Cload All other modes 6pF Cload Output Data Rise/Fall Time (3.3V) tr/tf 3G 10-bit 15pF Cload All other modes 15pF Cload Min Typ Max Units Notes STAT - - 0.4 ns 1 DBUS - - 0.3 ns 1 AUDIO - - 0.6 ns 1 STAT - - 0.4 ns 1 DBUS - - 0.4 ns 1 AUDIO - - 0.6 ns 1 STAT - - 1.5 ns 3 DBUS - - 1.1 ns 3 AUDIO - - 2.3 ns 3 STAT - - 1.5 ns 3 DBUS - - 1.4 ns 3 AUDIO - - 2.3 ns 3 STAT - - 0.5 ns 2 DBUS - - 0.4 ns 2 AUDIO - - 0.6 ns 2 STAT - - 0.5 ns 2 DBUS - - 0.4 ns 2 AUDIO - - 0.6 ns 2 STAT - - 1.6 ns 4 DBUS - - 1.5 ns 4 AUDIO - - 2.2 ns 4 STAT - - 1.6 ns 4 DBUS - - 1.4 ns 4 AUDIO - - 2.2 ns 4 Serial Digital Input Serial Input Data Rate DRSDI - 0.27 - 2.97 Gb/s - Serial Input Swing VSDI Differential with 100 load 500 800 1100 mVp-p - Serial Input Jitter Tolerance IJT Nominal loop bandwidth 0.7 0.8 - UI - DRSDO - 0.27 - 2.97 Gb/s - Square wave mod. Serial Digital Output Serial Output Data Rate GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 22 of 145 Table 2-4: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter Symbol Serial Output Swing VSDO Differential with 100 load Serial Output Rise Time 20% ~ 80% trSDO Serial Output Fall Time 20% ~ 80% Serial Output Intrinsic Jitter Serial Output Duty Cycle Distortion Min Typ Max Units Notes 350 - 600 mVp-p - - - - 180 ps - tfSDO - - - 180 ps - tOJ SMPTE colour bar 3G signal - - 100 ps - SMPTE colour bar HD signal - - 100 ps - SMPTE colour bar SD signal - - 400 ps - 3G - 10 - ps - HD - 10 - ps - SD - 20 - ps - DCDSDD Conditions Synchronous lock time - - - - 25 s - Asynchronous lock time - - 100 - 350 s - Lock time from power-up - - 325 ms - - - 60 MHz 5 40 50 60 % 5 1.5 - - ns 5 1.5 - - ns 5 After 20 minutes at -20C GSPI GSPI Input Clock Frequency fSCLK GSPI Input Clock Duty Cycle DCSCLK 50% levels 3.3V or 1.8V operation GSPI Input Data Setup Time - GSPI Input Data Hold Time - GSPI Output Data Hold Time - - 1.5 - - ns 5 CS low before SCLK rising edge - 50% levels 3.3V or 1.8V operation 1.5 - - ns 5 Time between end of command word (or data in Auto-Increment mode) and the first SCLK of the following data word - write cycle - 50% levels 3.3V or 1.8V operation 37.1 - - ns 5 Time between end of command word (or data in Auto-Increment mode) and the first SCLK of the following data word - read cycle - 50% levels 3.3V or 1.8V operation 148.4 - - ns 5 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 23 of 145 Table 2-4: AC Electrical Characteristics (Continued) Guaranteed over recommended operating conditions unless otherwise noted. Parameter CS high after SCLK falling edge Symbol - Conditions 50% levels 3.3V or 1.8V operation Min Typ Max Units Notes 37.1 - - ns 5 Notes: 1. 2. 3. 4. 5. 1.89V and 0C. 3.47V and 0C. 1.71V and 85C 3.13V and 85C Timing parameters defined in Section 4.20.3 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 24 of 145 3. Input/Output Circuits IO_VDD 200 Input Pin Figure 3-1: Digital Input Pin with Schmitt Trigger (20bit/10bit, AUDIO_EN/DIS, CS_TMS, SW_EN, IOPROC_EN/DIS, JTAG/HOST, RC_BYP, RESET_TRST, SCLK_TCK, SDIN_TDI, SDO_EN/DIS, STANDBY, TIM_861) IO_VDD 200 Output Pin Figure 3-2: Bidirectional Digital Input/Output Pin - Configured to Output unless in Reset Mode. (ACLK, AMCLK, AOUT_1/2, AOUT_3/4, AOUT_5/6, AOUT_7/8, DVB_ASI, SMPTE_BYPASS, WCLK) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 25 of 145 IO_VDD 200 Output Pin Figure 3-3: Bidirectional Digital Input/Output Pin with programmable drive strength. These pins are configured to output unless in Reset Mode; in which case they are high-impedance. The drive strength can be set by writing to address 06Dh in the host interface register. (DOUT0, DOUT1, DOUT2, DOUT3, DOUT4, DOUT5, DOUT6, DOUT7, DOUT8, DOUT9, SDOUT_TDO, STAT0, STAT1, STAT2, STAT3, STAT4, STAT5, XTAL_OUT, DOUT10, DOUT11, DOUT12, DOUT13, DOUT14, DOUT15, DOUT16, DOUT17, DOUT18, DOUT19, PCLK) XTAL1 XTAL2 XTAL_OUT Figure 3-4: XTAL1/XTAL2/XTAL-OUT A_VDD 2k VBG 50 Figure 3-5: VBG GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 26 of 145 SDI_VDD Out <0> LB_CONT Out <1> Figure 3-6: LB_CONT PLL_VDD 25 LF 25 Figure 3-7: Loop Filter SDI 50 TERM 50 SDI + - 5/6 VDD Figure 3-8: SDI/SDI and TERM BUFF_VDD 50 50 SDO SDO Figure 3-9: SDO/SDO GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 27 of 145 4. Detailed Description Refer to the document entitled GS2970/GS2971 Errata for this device (document number 53092). 4.1 Functional Overview The GS2970 is a multi-rate, multi-standard receiver with integrated SMPTE video processing as well as an integrated audio de-embedder, compliant with SMPTE 425M, SMPTE 424M, SMPTE 292 and SMPTE 259M-C signals. When used in conjunction with Gennum's 3Gb/s-capable equalizers, a complete receive solution that supports full bandwidth 1080p video at 2.97Gb/s can be realized. The GS2970 includes an integrated reclocker, serial data loop through output, robust serial-to-parallel conversion, integrated SMPTE video processing, and additional processing functions such as audio extraction, ancillary data extraction, EDH support, and DVB-ASI decoding. The device supports four distinct modes of operation that can be set through external device pins or by programming internal registers through the host interface; SMPTE mode, Data-Through mode, DVB-ASI mode and Standby mode. In SMPTE mode, all video processing features, ancillary data extraction, and audio de-embedding features are enabled by default. In DVB-ASI mode, the GS2970 carries out 8b/10b decoding and generates 10-bit parallel DVB-ASI compliant data. In Data-Through mode, the device operates as a simple serial to parallel converter. No additional processing features are enabled. Standby mode is the low power consumption mode of the device. In this mode, the internal reclocker will unlock, and the internal configuration registers will not be accessible through the host interface. The GS2970 includes a JTAG interface for boundary scan testing. 4.2 SMPTE 425M Mapping - 3G Level A and Level B Formats 4.2.1 Level A Mapping Data Stream 1 3FF 000 000 XYZ LN0 LN1 C RC 0 C RC 1 Audio Ctl Audio Ctl Audio Ctl Audio Ctl YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data YANC data 3FF 000 000 XYZ Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y27 Y28 Y29 Y30 Y31 Y32 Y33 Y34 Y35 Direct image format mapping - the mapping structure used to define 1080p/50/59.94/60 4:2:2 YCbCr 10 bit data, as supported by the GS2970. See Figure 4-1: Data Stream 2 HANC SAV Active Video 3FF 000 000 XYZ LN0 LN1 C RC 0 C RC 1 Audio data Audio data Audio data Audio data Audio data Audio data Audio data Audio data Audio data Audio data Audio data Audio data CANC data CANC data CANC data CANC data HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK HBLANK 3FF 000 000 XYZ Cb0 C r0 Cb1 C r1 Cb2 C r2 Cb3 C r3 Cb4 C r4 Cb5 C r5 Cb6 C r6 Cb7 C r7 Cb8 C r8 Cb9 C r9 Cb10 C r10 Cb11 C r11 Cb12 C r12 Cb13 C r13 Cb14 C r14 Cb15 C r15 Cb16 C r16 Cb17 C r17 EAV Figure 4-1: Level A Mapping GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 28 of 145 4.2.2 Level B Mapping The 2 x 292 HD SDI interface - this can be two distinct links running at 1.5Gb/s or one 3Gb/s link formatted according to SMPTE 292 on two 10-bit links (Y/C interleaved). For 1080p/50/59.94/60 4:2:2 video formats, each link should be line-interleaved as per SMPTE 372M. See Figure 4-2: 3FF 3FF 000 000 000 000 XYZ XYZ C b[1] 0 Y[1] 0 C r[1] 0 Y[1] 1 C b[1] 1 Y[1] 2 C r[1] 1 Y[1] 3 C b[1] 2 Y[1] 4 C r[1] 2 Y[1] 5 C b[1] 3 Y[1] 6 C r[1] 3 Y[1] 7 C b[1] 4 Y[1] 8 C r[1] 4 Y[1] 9 C b[1] 5 Y[1] 10 C r[1] 5 Y[1] 11 C b[1] 6 Y[1] 12 C r[1] 6 Y[1] 13 C b[1] 7 Y[1] 14 C r[1] 7 Y[1] 15 C b[1] 8 Y[1] 16 C r[1] 8 Y[1] 17 SAV Active Video 3FF 3FF 000 000 000 000 XYZ XYZ C b[2] 0 Y[2] 0 C r[2] 0 Y[2] 1 C b[2] 1 Y[2] 2 C r[2] 1 Y[2] 3 C b[2] 2 Y[2] 4 C r[2] 2 Y[2] 5 C b[2] 3 Y[2] 6 C r[2] 3 Y[2] 7 C b[2] 4 Y[2] 8 C r[2] 4 Y[2] 9 C b[2] 5 Y[2] 10 C r[2] 5 Y[2] 11 C b[2] 6 Y[2] 12 C r[2] 6 Y[2] 13 C b[2] 7 Y[2] 14 C r[2] 7 Y[2] 15 C b[2] 8 Y[2] 16 C r[2] 8 Y[2] 17 Audio data[1] Audio Ctl[1] Audio data[1] Audio Ctl[1] Audio data[1] Audio Ctl[1] Audio data[1] Audio Ctl[1] Audio data[1] YANC data[1] Audio data[1] YANC data[1] Audio data[1] YANC data[1] Audio data[1] YANC data[1] HANC Audio data[2] Audio Ctl[2] Audio data[2] Audio Ctl[2] Audio data[2] Audio Ctl[2] Audio data[2] Audio Ctl[2] Audio data[2] YANC data[2] Audio data[2] YANC data[2] Audio data[2] YANC data[2] Audio data[2] YANC data[2] Data Stream 2 ("Link 2") EAV 3FF 3FF 000 000 000 000 XYZ XYZ LN0 LN0 LN1 LN1 C RC 0 C RC 0 C RC 1 C RC 1 Data Stream 1 ("Link A") 3FF 3FF 000 000 000 000 XYZ XYZ LN0 LN0 LN1 LN1 C RC 0 C RC 0 C RC 1 C RC 1 multiplexed Y/C data "double" TRS headers from interleaved HD-SDI; Figure 4-2: Level B Mapping The GS2970 distinguishes between Level A and Level B mappings at 3Gb/s. When Level B data is detected, each 10-bit link is demultiplexed into its individual component streams, and most video processing features, including error detection and correction are enabled separately for Data Stream 1 and Data Stream 2 (Link A and Link B, respectively). NOTE: Audio demultiplexing and ancillary data extraction can only be enabled for one link for 3Gb/s Level B data. Data Stream 1 or Data Stream 2 can be selected via the host interface. 4.3 Serial Digital Input The GS2970 can accept serial digital inputs compliant with SMPTE 424M, SMPTE 292 and SMPTE 259M-C. The serial digital input buffer features 50 input termination and can be DC-coupled to Gennum's 3Gb/s-capable equalizers. 4.4 Serial Digital Loop-Through Output The GS2970 contains a 100 differential serial output buffer which can be configured to output either a retimed or a buffered version of the serial digital input. The SDO and SDO outputs of this buffer can interface directly to a 3Gb/s-capable, SMPTE compliant Gennum cable driver. See 5.1 Typical Application Circuit on page 140. When the RC_BYP pin is set HIGH, the serial digital output is the re-timed version of the serial input. When the RC_BYP pin is set LOW, the serial digital output is simply the buffered version of the serial input, bypassing the internal reclocker. The output can be disabled by setting the SDO_EN/DIS pin LOW. The output is also disabled when the STANDBY pin is asserted HIGH. When the output is disabled, both SDO and SDO pins are set to VDD and remain static. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 29 of 145 The SDO output is muted when the RC_BYP pin is set HIGH and the PLL is unlocked (LOCKED pin is LOW). When muted, the output is held static at logic `0' or logic `1'. Table 4-1: Serial Digital Output SDO_EN/DIS RC_BYP SDO/SDO 0 X Disabled 1 1 Re-timed 1 0 Buffered (not re-timed) NOTE: the serial digital output is muted when the GS2970 is unlocked. 4.5 Serial Digital Reclocker The GS2970 includes both a PLL stage and a sampling stage. The PLL is comprised of two distinct loops: * A coarse frequency acquisition loop sets the centre frequency of the integrated Voltage Controlled Oscillator (VCO) using an external 27MHz reference clock * A fine frequency and phase locked loop aligns the VCO's phase and frequency to the input serial digital stream The frequency lock loop results in a very fast lock time. The sampling stage re-times the serial digital input with the locked VCO clock. This generates a clean serial digital stream, which may be output on the SDO/SDO output pins and converted to parallel data for further processing. Parallel data is not affected by RC_BYP. Only the SDO is affected by this pin. 4.5.1 PLL Loop Bandwidth The fine frequency and phase lock loop in the GS2970 reclocker is non-linear. The PLL loop bandwidth scales with the jitter amplitude of the input data stream; automatically reduces bandwidth in response to higher jitter. This allows the PLL to reject more of the jitter in the input data stream and produce a very clean reclocked output. The loop bandwidth of the GS2970 PLL is defined with 0.2UI input jitter. The bandwidth is controlled by the LB_CONT pin. Under nominal conditions, with the LB_CONT pin floating and 0.2UI input jitter applied, the loop bandwidth is set to 1/1000 of the frequency of the input data stream. Connecting the LB_CONT pin to 3.3V reduces the bandwidth to half of the nominal setting. Connecting the LB_CONT pin to GND increases the bandwidth to double the nominal setting. Table 4-2 below summarizes this information. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 30 of 145 Table 4-2: PLL Loop Bandwidth Input Data Rate LB_CONT Pin Connection Loop Bandwidth (MHz)1 SD 3.3V 0.135 Floating 0.27 0V 0.54 3.3V 0.75 Floating 1.5 0V 3.0 3.3V 1.5 Floating 3.0 0V 6.0 HD 3G 1Measured with 0.2UI input jitter applied 4.6 External Crystal/Reference Clock The GS2970 requires an external 27MHz reference clock for correct operation. This reference clock is generated by connecting a crystal to the XTAL1 and XTAL2 pins of the device. See Application Reference Design on page 140. Table 4-3 shows XTAL characteristics. Alternately, a 27MHz external clock source can be connected to the XTAL1 pin of the device, as shown in Figure 4-3. The frequency variation of the crystal including aging, supply and temperature variation, should be less than +/-100ppm. The equivalent series resistance (or motional resistance) should be a maximum of 50. The external crystal is used in the frequency acquisition process. It has no impact on the output jitter performance of the part when the part is locked to incoming data. Because of this, the only key parameter is the frequency variation of the crystal that is stated above. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 31 of 145 External Crystal Connection External Clock Source Connection 16pF K6 K6 XTAL1 XTAL1 External Clock J6 NC XTAL2 J6 XTAL2 16pF Notes: 1. Capacitor values listed represent the total capacitance, including discrete capacitance and parasitic board capacitance. 2.XTAL1 serves as an input, which may alternatively accept a 27MHz clock source. Figure 4-3: 27MHz Clock Sources Table 4-3: Input Clock Requirements Parameter Min Typ Max UOM Notes XTAL1 Low Level Input Voltage (Vil) - - 20% of VDD_IO V 3 XTAL1 High Level Input Voltage (Vih) 80% of VDDIO - - V 3 XTAL1 Input Slew Rate 2 - - V/ns 3 XTAL1 to XOUT Prop. Delay (High to Low) 1.3 1.5 2.3 ns 3 XTAL1 to XOUT Prop. Delay (Low to High) 1.3 1.6 2.3 ns 3 NOTES: Valid when the cell is used to buffer an external clock source which is connected to the XTAL1 pin, then nothing should be connected to the XTAL2 pin. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 32 of 145 4.7 Lock Detect The LOCKED output signal is available by default on the STAT3 output pin, but may be programmed to be output through any one of the six programmable multi-functional pins of the device; STAT[5:0]. The LOCKED output signal is set HIGH by the Lock Detect block under the following conditions: Table 4-4: Lock Detect Conditions Mode of Operation Mode Setting Condition for Locked Data-Through Mode SMPTE_BYPASS = LOW DVB_ASI = LOW Reclocker PLL is locked. SMPTE Mode SMPTE_BYPASS = HIGH DVB_ASI = LOW Reclocker PLL is locked 2 consecutive TRS words are detected in a 2-line window. DVB_ASI Mode SMPTE_BYPASS = LOW DVB_ASI = HIGH Bit AUTO/MAN = LOW Reclocker PLL is locked 32 consecutive DVB_ASI words with no errors are detected within a 128-word window. NOTE 1: The part will lock to ASI in Auto mode, but could falsely unlock for some ASI input patterns. NOTE 2: In Standby mode, the reclocker PLL unlocks. However, the LOCKED signal retains whatever state it previously held. So, if before Standby assertion, the LOCKED signal is HIGH, then during standby, it remains HIGH regardless of the status of the PLL. 4.7.1 Asynchronous Lock The lock detection algorithm is a continuous process, beginning at device power-up or after a system reset. It continues until the device is powered down or held in reset. The device first determines if a valid serial digital input signal has been presented to the device. If no valid serial data stream has been detected, the serial data into the device is considered invalid, and the LOCKED signal is LOW. Once a valid input signal has been detected, the asynchronous lock algorithm enters a "hunt" phase, in which the device attempts to detect the presence of either TRS words or DVB-ASI sync words. By default, the device powers up in auto mode (the AUTO/MAN bit in the host interface is set HIGH). In this mode, the device operating frequency toggles between 3G, HD and SD rates as it attempts to lock to the incoming data rate. The PCLK output continues to operate, and the frequency may switch between 148.5MHz, 74.25MHz, 27MHz and 13.5MHz. When the device is operating in manual mode (AUTO/MAN bit in the host interface is LOW), the operating frequency needs to be set through the host interface using the RATE_DET[1:0] bits. In this mode, the asynchronous lock algorithm does not toggle the operating rate of the device and attempts to lock within a single standard. Lock is achieved within three lines of the selected standard. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 33 of 145 4.7.2 Signal Interruption The device tolerates a signal interruption of up to 10s without unlocking, as long as no TRS words are deleted by this interruption. If a signal interruption of greater than 10s is detected, the lock detection algorithm may lose the current data rate, and LOCKED will de-assert until the data rate is re-acquired by the lock detection block. 4.8 SMPTE Functionality 4.8.1 Descrambling and Word Alignment The GS2970 performs NRZI to NRZ decoding and data descrambling according to SMPTE 424M/SMPTE 292/SMPTE 259M-C and word aligns the data to TRS sync words. When operating in manual mode (AUTO/MAN = LOW), the device only carries out SMPTE decoding, descrambling and word alignment when the SMPTE_BYPASS pin is set HIGH and the DVB_ASI pin is set LOW. When operating in Auto mode (AUTO/MAN = HIGH), the GS2970 carries out descrambling and word alignment to enable the detection of TRS sync words. When two consecutive valid TRS words (SAV and EAV), with the same bit alignment have been detected, the device word-aligns the data to the TRS ID words. TRS ID word detection is a continuous process. The device remains in SMPTE mode until TRS ID words fail to be detected. NOTE 1: Both 8-bit and 10-bit TRS headers are identified by the device. NOTE 2: In 3G Level B mode, the device only supports Data Stream 1 and Data Stream 2 having the same bit width (i.e. both data streams contain 8-bit data, or both data streams contain 10-bit data). If the bit widths between the two data streams are different, the GS2970 cannot word align the input stream, and switches in Data-Through mode. 4.9 Parallel Data Outputs The parallel data outputs are aligned to the rising edge of the PCLK. 4.9.1 Parallel Data Bus Buffers The parallel data bus, status signal outputs and control signal input pins are all connected to high-impedance buffers. The device supports 1.8 or 3.3V (LVTTL and LVCMOS levels) supplied at the IO_VDD and IO_GND pins. All output buffers (including the PCLK output), are set to high-impedance in Reset mode (RESET_TRST = LOW). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 34 of 145 I/O Timing Specs: 10-bit SDR Mode: 6.734ns (HD 10-bit) 37.037ns (SD 10-bit) DBUS[19:10] Y0 Cr0 80% Y1 Cb1 80% PCLK_OUT 20% toh 20% tr tf tod 10bHD Mode 3.3V dbus stat toh 1.000ns 1.000ns tr/tf (min) 0.400ns 0.500ns Cload 6 pF tod tr/tf (max) 3.700ns 1.400ns 4.100ns 1.600ns 1.8V Cload 15 pF toh 1.000ns 1.000ns tr/tf (min) 0.400ns 0.400ns Cload toh tr/tf (min) 19.400ns 0.400ns 19.400ns 0.400ns Cload 6 pF tod tr/tf (max) 3.700ns 1.400ns 4.400ns 1.500ns Cload 15 pF 10bSD Mode 3.3V dbus stat toh tr/tf (min) 19.400ns 0.400ns 19.400ns 0.500ns Cload 6 pF tod tr/tf (max) 22.200ns 1.400ns 22.200ns 1.600ns 1.8V Cload 15 pF 6 pF tod tr/tf (max) 22.200ns 1.400ns 22.200ns 1.500ns Cload 15 pF Figure 4-4: PCLK to Data and Control Signal Output Timing - SDR Mode 1 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 35 of 145 I/O Timing Specs: 20-bit SDR Mode: 6.734ns (3G 20-bit) 13.468ns (HD 20-bit) 74.074ns (SD 20-bit) DBUS[19:10] Y0 Y1 Y2 Y3 DBUS[9:0] Cb0 Cr0 Cb1 Cr1 80% 80% PCLK_OUT 20% toh 20% tr tf tod 20b3G and 20bHD Modes 3.3V dbus stat toh 1.000ns 1.000ns tr/tf (min) 0.400ns 0.500ns Cload 6 pF tod tr/tf (max) 3.700ns 1.400ns 4.100ns 1.600ns 1.8V Cload 15 pF toh 1.000ns 1.000ns tr/tf (min) 0.400ns 0.400ns Cload toh tr/tf (min) 38.000ns 0.400ns 38.000ns 0.400ns Cload 6 pF tod tr/tf (max) 3.700ns 1.400ns 4.400ns 1.500ns Cload 15 pF 20bSD Mode 3.3V dbus stat toh tr/tf (min) 38.000ns 0.400ns 38.000ns 0.500ns Cload 6 pF tod tr/tf (max) 41.000ns 1.400ns 41.000ns 1.600ns 1.8V Cload 15 pF 6 pF tod tr/tf (max) 41.000ns 1.400ns 41.000ns 1.500ns Cload 15 pF Figure 4-5: PCLK to Data and Control Signal Output Timing - SDR Mode 2 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 36 of 145 I/O Timing Specs: DDR Mode: 6.734ns 3.367ns DBUS[19:10] Y0 Cr0 Y1 80% Cb1 Y2 Cr1 Y3 80% PCLK_OUT 20% toh toh tod 20% tr tf tod 10b3G Mode 3.3V dbus stat toh 0.450ns 0.450ns tr/tf (min) 0.400ns 0.500ns Cload 6 pF 1.8V tod tr/tf (max) 1.900ns 1.500ns 2.200ns 1.600ns Cload 15 pF toh 0.400ns 0.450ns tr/tf (min) 0.300ns 0.400ns Cload 6 pF tod tr/tf (max) 1.800ns 1.100ns 2.500ns 1.500ns Cload 15 pF Figure 4-6: PCLK to Data and Control Signal Output Timing - DDR Mode The GS2970 has a 20-bit output parallel bus, which can be configured for different output formats as shown in Table 4-5. Table 4-5: GS2970 Output Video Data Format Selections Output Data Format Pin/Register Bit Settings DOUT[9:0] DOUT[19:10] 20BIT /10BIT RATE_ SEL0 RATE_ SEL1 SMPTE_ BYPASS DVB-ASI 20-bit demultiplexed HD format HIGH LOW LOW HIGH LOW Chroma Luma 20-bit data output HD format HIGH LOW LOW LOW LOW DATA DATA 20-bit demultiplexed SD format HIGH HIGH X HIGH LOW Chroma Luma 20-bit data output SD format HIGH HIGH X LOW LOW DATA DATA 10-bit multiplexed 3G DDR format LOW LOW HIGH HIGH LOW Driven LOW Data Stream One/ Data Stream Two* 10-bit multiplexed HD format LOW LOW LOW HIGH LOW Driven LOW Luma/Chroma 10-bit data output HD format LOW LOW LOW LOW LOW Driven LOW DATA GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 37 of 145 Table 4-5: GS2970 Output Video Data Format Selections (Continued) Output Data Format Pin/Register Bit Settings DOUT[9:0] DOUT[19:10] 20BIT /10BIT RATE_ SEL0 RATE_ SEL1 SMPTE_ BYPASS DVB-ASI 10-bit multiplexed SD format LOW HIGH X HIGH LOW Driven LOW Luma/Chroma 10-bit data output SD format LOW HIGH X LOW LOW Driven LOW DATA 20-bit demultiplexed 3G format HIGH LOW HIGH HIGH LOW Data Stream Two* Data Stream One* DVB-ASI format LOW HIGH X - HIGH DOUT19 = WORD_ERR DOUT18 = SYNC_OUT DOUT17 = H_OUT DOUT16 = G_OUT DOUT15 = F_OUT DOUT14 = E_OUT DOUT13 = D_OUT DOUT12 = C_OUT DOUT11 = B_OUT DOUT10 = A_OUT *In 3G Mode, the data streams can be swapped at the output through the host interface. NOTE: When in Auto Mode, swap RATE_SEL with RATE_DET. 4.9.2 Parallel Output in SMPTE Mode When the device is operating in SMPTE mode (SMPTE_BYPASS = HIGH and DVB_ASI = LOW), data is output in either Multiplexed or Demultiplexed form depending on the setting of the 20bit/10bit pin. When operating in 20-bit mode (20bit/10bit = HIGH), the output data is demultiplexed Luma and Chroma data for SD and HD data rates, and Data Stream 1 and Data Stream 2 for the 3G data. When operating in 10-bit mode (20bit/10bit = LOW), the output data is multiplexed Luma and Chroma data for SD and HD data rates, and multiplexed Data Stream 1 and Data Stream 2 for the 3G data. In this mode, the data is presented on the DOUT[19:10] pins, with DOUT[9:0] being forced LOW. 4.9.3 Parallel Output in DVB-ASI Mode In DVB-ASI mode, the 20bit/10bit pin must be set LOW to configure the output parallel bus for 10-bit operation. DVB-ASI mode is enabled when the AUTO/MAN bit is LOW, SMPTE_BYPASS pin is LOW and the DVB_ASI pin is HIGH. The extracted 8-bit data is presented on DOUT[17:10] such that DOUT[17:10] = HOUT ~ AOUT, where AOUT is the least significant bit of the decoded transport stream data. In addition, the DOUT19 and DOUT18 pins are configured as DVB-ASI status signals WORDERR and SYNCOUT respectively. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 38 of 145 SYNCOUT is HIGH whenever a K28.5 sync character is output from the device. WORDERR is HIGH whenever the device has detected a running disparity error or illegal code word. 4.9.4 Parallel Output in Data-Through Mode This mode is enabled when the SMPTE_BYPASS and DVB_ASI pins are LOW. In this mode, data is passed to the output bus without any decoding, descrambling or word-alignment. The output data width (10-bit or 20-bit) is controlled by the setting of the 20bit/10bit pin. NOTE: In order to use Data-Through Mode, a 3G-B input signal must not be connected at the input of the device when the switch is made from Auto Mode to Data-Through Mode. 4.9.5 Parallel Output Clock (PCLK) The frequency of the PCLK output signal of the GS2970 is determined by the output data rate and the 20bit/10bit pin setting. Table 4-6 lists the output signal formats according to the data format selected in Manual mode (AUTO/MAN bit in the host interface is set LOW), or detected in Auto mode (AUTO/MAN bit in the host interface is set HIGH). Table 4-6: GS2970 PCLK Output Rates Output Data Format Pin/Control Bit Settings PCLK Rate 20bit/ 10bit RATE_DET0 RATE_DET1 SMPTE_ BYPASS DVB-ASI 20-bit demultiplexed HD format HIGH LOW LOW HIGH LOW 74.25 or 74.25/1.001MHz 20-bit data output HD format HIGH LOW LOW LOW LOW 74.25 or 74.25/1.001MHz 20-bit demultiplexed SD format HIGH HIGH X HIGH LOW 13.5MHz 20-bit data output SD format HIGH HIGH X LOW LOW 13.5MHz 20-bit demultiplexed 3G format HIGH LOW HIGH HIGH LOW 148.5 or 148.5/1.001MHz 10-bit multiplexed 3G DDR format LOW LOW HIGH HIGH LOW 148.5 or 148.5/1.001MHz 10-bit multiplexed HD format LOW LOW LOW HIGH LOW 148.5 or 148.5/1.001MHz 10-bit data output HD format LOW LOW LOW LOW LOW 148.5 or 148.5/1.001MHz 10-bit multiplexed SD format LOW HIGH X HIGH LOW 27MHz GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 39 of 145 Table 4-6: GS2970 PCLK Output Rates (Continued) Output Data Format Pin/Control Bit Settings PCLK Rate 20bit/ 10bit RATE_DET0 RATE_DET1 SMPTE_ BYPASS DVB-ASI 10-bit data output SD format LOW HIGH X LOW LOW 27MHz 10-bit ASI output SD format LOW HIGH X LOW HIGH 27MHz 4.9.6 DDR Parallel Clock Timing The GS2970 has the ability to transmit 10-bit parallel video data with a DDR (Dual Data Rate) pixel clock over a single-ended interface. DDR Mode can be enabled when the SDI data bandwidth is 3Gb/s. In this case, the 10-bit parallel data rate is 297Mb/s, and the frequency of the DDR clock is 148.5MHz (10-bit output in 3G mode). The DDR pixel clock avoids the need to operate a high-drive pixel clock at 297MHz. This reduces power consumption, clock drive strength, and noise generation, and precludes from generating excessive EMI had PCLK on the board have to run at 297MHz. It also enables easier board routing and avoids the need to use the higher-speed I/Os on FPGAs, which may require more expensive speed grades. Figure 4-7 shows how the DDR interface operates. The pixel clock is transmitted at half the data rate, and the interleaved data is sampled at the receiver on both clock edges. 20-bit bus (transition rate = 74.25MHz) Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Cb0 Cr0 Cb1 Cr1 Cb2 Cr2 Cb3 Cr3 Cb4 Cr4 Y0 Cb Y1 0 Y6 Cb Y7 3 Y8 Cb Y9 4 10-bit bus (transition rate = 148.5MHz) Cr Cb Y2 Y3 0 1 Cr Cb Y4 Y5 1 2 Cr 2 Cr 3 Cr 4 PCLK (148.5MHz) Figure 4-7: DDR Video Interface The GS2970 has the ability to shift the Setup/Hold window on the receive interface, by using an on-chip delay line to shift the phase of PCLK with respect to the data bus. The timing of the PCLK output, relative to the data, can be adjusted through the host interface registers. Address 06Ch contains the delay line controls: Bit[5] (DEL_LINE_CLK_SEL) is a coarse delay adjustment that selects between the default (nominal) PCLK phase and a quadrature phase, for a 90 phase shift. Bits[4:0] (DEL_LINE_OFFSET) comprise a fine delay adjustment to shift the PCLK in 40ps increments (typical conditions). The maximum fine delay adjustment is approximately 1.2ns under nominal conditions. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 40 of 145 An example delay adjustment over min/typ/max conditions is illustrated in Figure 4-8. The target delay is 0.84 ns under typical conditions (approximately 45 PCLK phase shift), and requires a control word setting of 0x0014 for address 0x006C. 90 phase shift 6.734ns 3.367ns 1.684ns PCLK 0.842ns offset [5] = 1 (90 phase shift) Typical 45 phase shift 6.734ns 3.367ns Ranges: 1.684ns PCLK (MIN) 0.58ns delay PCLK (TYP) 0.84ns delay PCLK (MAX) 1.38ns delay Figure 4-8: Delay Adjustment Ranges 4.10 Timing Signal Generator The GS2970 has an internal timing signal generator which is used to generate digital FVH timing reference signals, to detect and correct certain error conditions and automatic video standard detection. The timing signal generator is only operational in SMPTE mode (SMPTE_BYPASS = HIGH). The timing signal generator consists of a number of counters and comparators operating at video pixel and video line rates. These counters maintain information about the total line length, active line length, total number of lines per field/frame and total active lines per field/frame for the received video standard. It takes one video frame to obtain full synchronization to the received video standard. NOTE: Both 8-bit and 10-bit TRS words are identified by the device. Once synchronization has been achieved, the timing signal generator continues to monitor the received TRS timing information to maintain synchronization. The timing signal generator re-synchronizes all pixel and line based counters on every received TRS ID. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 41 of 145 NOTE: For correct operation of the timing signal generator, the SW_EN input pin must be set LOW, unless manual synchronous switching is enabled (Section 4.10.1). 4.10.1 Manual Switch Line Lock Handling The principle of switch line lock handling is that the switching of synchronous video sources will only disturb the horizontal timing and alignment, whereas the vertical timing remains in synchronization - i.e. switching between video sources of the same format. To account for the horizontal disturbance caused by a synchronous switch, the word alignment block and timing signal generator automatically re-synchronizes to the new timing immediately if the synchronous switch happens during the designated switch line, as defined in SMPTE recommended practice RP168-2002. The device samples the SW_EN pin on every PCLK cycle. When a Logic LOW to HIGH transition on this pin is detected anywhere within the active line, the word alignment block and timing signal generator re-synchronize immediately to the next TRS word. This allows the system to force immediate lock on any line, if the switch point is non-standard. To ensure proper switch line lock handling, the SW_EN signal should be asserted HIGH anywhere within the active portion of the line on which the switch has taken place, and should be held HIGH for approximately one video line. After this time period, SW_EN should be de-asserted. SW_EN should be held LOW during normal device operation. NOTE: It is the rising edge of the SW_EN signal, which generates the switch line lock re-synchronization. This edge must be in the active portion of the line containing the video switch point. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 42 of 145 Switch point V ideo source 1 Video source 2 EAV EAV ANC ANC SAV SAV AC TIVE PICTU RE E AV AC TIVE PICTU RE EAV ANC ANC S AV EA V ACTIVE P ANC ICTUR E SAV E AV ACTIVE PICTUR ANC E EAV ANC EAV SA V ACTIVE PICTURE EAV A NC SAV ANC S AV ACTIVE PICTURE EAV ANC SAV sw itch video source 1 to 2 DA TA IN EAV ANC SAV AC TIVE PICTU RE E AV ANC S AV ACTIVE PICTURE ANC EAV ANC S AV ACTIVE PICTURE EAV ANC SAV D ATA O U T EAV ANC SAV AC TIVE PICTU RE E AV ANC S AV ACTIVE PICTURE ANC EAV ANC S AV ACTIVE PICTURE EAV ANC SAV TRS position SW _EN Re-synchronization Switch point Video source 1 Video source 2 EAV EAV ANC ANC SAV SAV AC TIVE PICTU RE E AV AC TIVE PICTU RE EAV ANC ANC S AV EA V ACTIVE P ANC ICTUR E SAV E AV ACTIVE PICTUR ANC E EAV ANC EAV SA V ANC S AV ACTIVE PICTURE ACTIVE PICTURE EAV EAV A NC ANC SAV SAV sw itch video source 2 to 1 DA TA IN EAV ANC SAV AC TIVE PICTU RE EAV ANC SAV ACTIVE PICTURE EAV ANC SA V ACTIVE PICTURE EAV A NC SAV D ATA O U T EAV ANC SAV AC TIVE PICTU RE EAV ANC SAV ACTIVE PICTURE EAV ANC SA V ACTIVE PICTURE EAV A NC SAV TRS position SW _EN Re-synchronization Figure 4-9: Switch Line Locking on a Non-Standard Switch Line 4.10.2 Automatic Switch Line Lock Handling The synchronous switch point is defined for all major video standards in SMPTE RP168-2002. The device automatically re-synchronizes the word alignment block and timing signal generator at the switch point, based on the detected video standard. The device, as described in Section 4.10.1 and Figure 4-9 above, implements the re-synchronization process automatically, every field/frame. The switch line is defined as follows: * For 525 line interlaced systems: resynchronization takes place at then end of lines 10 & 273 * For 525 line progressive systems: resynchronization takes place at then end of line 10 * For 625 line interlaced systems: resynchronization takes place at then end of lines 6 & 319 * For 625 line progressive systems: resynchronization takes place at then end of line 6 * For 750 line progressive systems: resynchronization takes place at then end of line 7 * For 1125 line interlaced systems: resynchronization takes place at then end of lines 7 & 568 * For 1125 line progressive systems: resynchronization takes place at then end of line 7 NOTE: Unless indicated by SMPTE 352M payload identifier packets, the GS2970 does not distinguish between 1125-line progressive segmented-frame (PsF) video and 1125-line interlaced video operating at 25 or 30fps. However. PsF video operating at 24fps is detected by the device. A full list of all major video standards and switching lines is shown in Table 4-7. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 43 of 145 4.10.3 Switch Line Lock Handling During Level B to Level A Conversion When 3G data is detected by the GS2970, and Level B to Level A conversion is enabled, the device only supports a limited phase offset between two synchronous video sources if a synchronous switch is implemented. If the synchronous switch point results in an "extended" active video period, the GS2970 only re-synchronizes to the following TRS ID if the phase difference between the two sources is less than or equal to 10s. If the phase difference is greater than 10s, the GS2970 takes one additional line to re-synchronize. In this case, the user may observe a missing H pulse on the line following the switch line, on the H timing output. NOTE: This 10s constraint is only valid when Level B to Level A conversion is enabled, and only when the synchronous switch point results in an extended active video area. Table 4-7: Switch Line Position for Digital Systems System Frame Rate & Structure 1125 60/P 750 Pixel Structure 1920x1080 4:2:2 Signal Standard Parallel Interface 274M + RP211 50/P 274M + RP211 60/I 274M + RP211 50/I 274M + RP211 30/P 274M + RP211 25/P 274M + RP211 24/P 274M + RP211 30/PsF 274M + RP211 25/PsF 274M + RP211 24/PsF 274M + RP211 60/P 1280x720 4:2:2 296M 50/P 296M 30/P 296M 25/P 296M 24/P 296M GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Serial Interface Line No. 292 7 7/569 7 292 7 44 of 145 Table 4-7: Switch Line Position for Digital Systems (Continued) System Frame Rate & Structure 625 50/P Pixel Structure 720x576 4:2:2 4:2:0 50/I 960x576 720x576 4:2:2 4:4:4:4 4:2:2 525 59.94/P 720x483 4:2:2 4:2:0 59.94/I 960x483 720x483 4:2:2 4:4:4 4:2:2 HD-SDTI P or PsF structure 1920x1080 4:2:2 I structure SDTI Signal Standard Parallel Interface Serial Interface Line No. BT.1358 349M 292 6 BT.1358 347M 344M BT.1358 BT.1358 BT.1362 BT.1358 349M 292 BT.1358 BT.1358 BT.1362 BT.601 349M 292 BT.601 BT.656 259M BT.799 349M 292 BT.799 347M 344M BT.799 BT.799 344M BT.799 BT.799 - BT.601 349M 292 BT.601 125M 259M 293M 349M 292 293M 347M 344M 293M 293M 294M 293M 349M 292 293M 293M 294M 267M 349M 292 267M 267M 259M 267M 349M 292 267M 347M 344M 267M RP174 344M 267M RP175 RP175 125M 349M 292 125M 125M 259M 274M 274M + 348M 292 274M P structure 1280x720 50/I 720x576 59.94/I 720x483 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 4:2:2 6/319 10 10/273 7 7/569 296M 296M + 348M BT.656 BT.656 + 305M 125M 125M + 305M 7 259M 6/319 10/273 45 of 145 4.11 Programmable Multi-function Outputs The GS2970 has 6 multi-function output pins, STAT [5:0], which are programmable via the host interface to output one of the following signals: Table 4-8: Output Signals Available on Programmable Multi-Function Pins Status Signal Selection Code Default Output Pin H/HSYNC (according to TIM_861 Pin) Section 4.12 0000 STAT 0 V/VSYNC (according to TIM_861 Pin) Section 4.12 0001 STAT 1 F/DE (according to TIM_861 Pin) Section 4.12 0010 STAT 2 LOCKED Section 4.7 0011 STAT 3 Y/1ANC Section 4.17 0100 STAT 4 C/2ANC Section 4.17 0101 - DATA ERROR Section 4.16 0110 STAT 5 VIDEO ERROR 0111 - AUDIO ERROR 1000 - EDH DETECTED 1001 - CARRIER DETECT 1010 - RATE_DET0 1011 - RATE_DET1 1100 - NOTE: Each of the STAT[5:0] pins are configurable individually using the register bits in the host interface; STAT[5:0]_CONFIG (008h/009h). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 46 of 145 4.12 H:V:F Timing Signal Generation The GS2970 extracts critical timing parameters from the received TRS words. Horizontal blanking (H), Vertical blanking (V), and Field odd/even (F) timing are output on the STAT[2:0] pins by default. Using the H_CONFIG bit in the host interface, the H signal timing can be selected as one of the following: 1. Active line blanking (H_CONFIG = LOW) - the H output is HIGH for the horizontal blanking period, including the EAV TRS words. 2. TRS based blanking (H_CONFIG = HIGH) - the H output is set HIGH for the entire horizontal blanking period as indicated by the H bit in the received TRS signals. The timing of these signals is shown in the figures below. NOTE: Both 8-bit and 10-bit TRS words are identified by the device. PCLK LUMA DATA CHROMA DATA H V F 3FF 000 000 XYZ (EAV) 3FF 000 000 XYZ (SAV) 3FF 000 000 XYZ (EAV) 3FF 000 000 XYZ (SAV) Figure 4-10: H:V:F Output Timing - 3G Level A and HDTV 20-bit Mode PCLK (3G DDR) PCLK (HD) MULTIPLEXED Y'CbCr DATA (HD) MULTIPLEXED DS1/DS2 DATA (3G) H V F 3FF 3FF 000 000 000 000 XYZ (EAV) XYZ (EAV) H VF T IM IN G A T E A V PCLK (3G DDR) PCLK (HD) MULTIPLEXED Y'CbCr DATA (HD) MULTIPLEXED DS1/DS2 DATA (3G) 3FF 3FF 000 000 000 000 XYZ (SAV) XYZ (SAV) H V F H VF T IM IN G A T S A V H S IG N A L T IM IN G : H _ C O N F IG = L O W H _ C O N F IG = H IG H Figure 4-11: H:V:F Output Timing - 3G Level A and HDTV 10-bit Mode 3G Level B 20-bit Mode, each 10-bit stream PCLK (DDR) MULTIPLEXED LINKA/LINKB DATA H V F 3FF 3FF 3FF 3FF 000 000 000 000 000 000 000 000 XYZ (eav) XYZ (eav) XYZ (eav) XYZ (eav) H VF T IM IN G A T E A V PCLK (DDR) MULTIPLEXED LINKA/LINKB DATA H V 3FF 3FF 3FF 3FF 000 000 000 000 000 000 000 000 XYZ (sav) XYZ (sav ) XYZ (sav ) XYZ (sav ) F H VF T IM IN G A T S A V H S IG N A L T IM IN G : H _ C O N F IG = L O W H _ C O N F IG = H IG H Figure 4-12: H:V:F Output Timing - 3G Level B 10-bit Mode GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 47 of 145 PC LK L U M A D A T A IN P U T C H R O M A D A T A IN P U T H V F 3FF 000 000 X Y Z (EAV) 3FF 000 000 X Y Z (SAV) 3FF 000 000 X Y Z (EAV) 3FF 000 000 X Y Z (SAV) H S IG N A L T IM IN G : H _ C O N F IG = L O W H _ C O N F IG = H IG H Figure 4-13: H:V:F Output Timing - HD 20-bit Output Mode PC LK M U L T IP L E X E D Y 'C b C r D A T A IN P U T 3FF 3FF 000 000 000 000 X Y Z (EAV) X Y Z (EAV) H V F H V F T IM IN G A T E A V PC LK M U L T IP L E X E D Y 'C b C r D A T A IN P U T 3FF 3FF 000 000 000 000 X Y Z (SAV) X Y Z (SAV) H V F H V F T IM IN G A T S A V Figure 4-14: H:V:F Output Timing - HD 10-bit Output Mode P C LK C H R O M A D A T A IN P U T L U M A D A T A IN P U T H V F 3FF 000 3FF 000 000 X Y Z (EAV) 000 X Y Z (SAV) H S IG N A L T IM IN G : H _ C O N F IG = L O W H _ C O N F IG = H IG H Figure 4-15: H:V:F Output Timing - SD 20-bit Output Mode PC LK M U L T IP L E X E D Y 'C b C r D A T A IN P U T H V F 3FF 000 H S IG N A L T IM IN G : 000 X Y Z (EAV) H _ C O N F IG = L O W 3FF 000 000 X Y Z (SAV) H _ C O N F IG = H IG H Figure 4-16: H:V:F Output Timing - SD 10-bit Output Mode 4.12.1 CEA-861 Timing Generation The GS2970 is capable of generating CEA 861 timing instead of SMPTE HVF timing for all of the supported video formats. This mode is selected when the TIM_861 pin is HIGH. Horizontal sync (HSYNC), Vertical sync (VSYNC), and Data Enable (DE) timing are output on the STAT[2:0] pins by default. Table 4-9 shows the CEA-861 formats supported by the GS2970: GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 48 of 145 Table 4-9: Supported CEA-861 Formats Format CEA-861 Format VD_STD[5:0] 720(1440) x 480i @ 59.94/60Hz 6&7 16h, 17h, 19h, 1Bh 720(1440) x 576i @ 50Hz 21 & 22 18h, 1Ah 1280 x 720p @ 59.94/60Hz 4 20h, 00h 1280 x 720p @ 50Hz 19 24h, 04h 1920 x 1080i @ 59.94/60Hz 5 2Ah, 0Ah 1920 x 1080i @ 50Hz 20 2Ch, 0Ch 1920 x 1080p @ 29.97/30Hz 341 2Bh, 0Bh 1920 x 1080p @ 25Hz 332 2Dh, 0Dh 1920 x 1080p @ 23.98/24Hz 32 30h, 10h 1920 x 1080p @ 59.94/60Hz 161 2Bh 1920 x 1080p @ 50Hz 312 2Dh NOTES: 1,2: Timing is identical for the corresponding formats. 4.12.1.1 Vertical Timing When CEA861 timing is selected, the device outputs standards compliant CEA861 timing signals as shown in the figures below; for example 240 active lines per field for SMPTE 125M. The register bit TRS_861 is used to select DFP timing generator mode which follows the vertical blanking timing as defined by the embedded TRS code words. The timing of the CEA 861 timing reference signals can be found in the CEA 861 specifications. For information, they are included in the following diagrams. These diagrams may not be comprehensive. Table 4-10: CEA861 Timing Formats Format Parameters 4 H:V:DE Input Timing 1280 x 720p @ 59.94/60Hz 5 H:V:DE Input Timing 1920 x 1080i @ 59.94/60Hz 6&7 H:V:DE Input Timing 720 (1440) x 480i @ 59.94/60Hz 19 H:V:DE Input Timing 1280 x 720p @ 50Hz 20 H:V:DE Input Timing 1920 x 1080i @ 50Hz 21&22 H:V:DE Input Timing 720 (1440) x 576 @ 50Hz 16 H:V:DE Input Timing 1920 x 1080p @ 59.94/60Hz 31 H:V:DE Input Timing 1920 x 1080p @ 50Hz GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 49 of 145 Table 4-10: CEA861 Timing Formats (Continued) Format Parameters 32 H:V:DE Input Timing 1920 x 1080p @ 23.94/24Hz 33 H:V:DE Input Timing 1920 x 1080p @ 25Hz 34 H:V:DE Input Timing 1920 x 1080p @ 29.97/30Hz 1660 Total Horizontal Clocks per line Data Enable 370 1280 Clocks for Active Video 40 110 220 clocks HSYNC ~ ~ ~ 720 Active Vertical Lines ~ Progressive Frame: 30 Vertical Blanking Lines ~ ~ ~ ~ Data Enable 110 1650 clocks 260 745 746 747 748 749 750 1 2 3 4 5 6 7 25 26 ~ ~ ~ ~ HSYNC 745 746 750 VSYNC Figure 4-17: H:V:DE Output Timing 1280 x 720p @ 59.94/60 (Format 4) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 50 of 145 2200 Total Horizontal Clocks per line Data Enable 280 44 88 1920 Clocks for Active Video 148 clocks HSYNC ~ ~ ~ ~ ~ Data Enable ~ 540 Active Vertical Lines per field Field 1: 22 Vertical Blanking Lines 2200 clocks 88 192 ~ ~ HSYNC 1123 1124 1125 1 2 3 4 5 6 7 8 19 20 21 560 561 562 VSYNC ~ ~ 561 562 563 564 565 566 567 568 ~ 192 HSYNC 560 ~ 2200 clocks 1100 88 ~ ~ ~ Data Enable ~ 540 Active Vertical Lines per field Field 2: 23 Vertical Blanking Lines 569 570 582 583 584 1123 1124 1125 VSYNC Figure 4-18: H:V:DE Output Timing 1920 x 1080i @ 59.94/60 (Format 5) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 51 of 145 1716 Total Horizontal Clocks per line Data Enable 276 124 38 1440 Clocks for Active Video 114 clocks HSYNC ~ ~ ~ ~ ~ Data Enable 240 Active Vertical Lines per field ~ Field 1: 22 Vertical Blanking Lines 1716 clocks 38 238 HSYNC 524 525 1 2 3 4 5 6 7 8 9 21 22 261 262 263 VSYNC ~ ~ 240 Active Vertical Lines per field Field 2: 23 Vertical Blanking Lines ~ ~ Data Enable 1716 clocks 38 238 858 HSYNC 284 285 261 262 263 264 265 266 267 268 269 270 271 524 525 1 VSYNC Figure 4-19: H:V:DE Output Timing 720 (1440) x 480i @ 59.94/60 (Format 6&7) 1980 Total Horizontal Clocks per line Data Enable 700 40 440 1280 Clocks for Active Video 220 clocks HSYNC ~ 1980 clocks 260 745 746 747 748 749 750 1 2 3 4 5 6 7 ~ ~ ~ HSYNC ~ ~ 440 ~ ~ ~ ~ Data Enable ~ 720 Active Vertical Lines Progressive Frame: 30 Vertical Blanking Lines 25 26 745 746 750 VSYNC Figure 4-20: H:V:DE Output Timing 1280 x 720p @ 50 (Format 19) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 52 of 145 2640 Total Horizontal Clocks per line Data Enable 720 44 1920 Clocks for Active Video 148 clocks 528 HSYNC ~ ~ ~ ~ ~ Data Enable ~ 540 Active Vertical Lines per field Field 1: 22 Vertical Blanking Lines 2640 clocks 528 192 ~ ~ HSYNC 1123 1124 1125 1 2 3 4 5 6 7 8 19 20 21 560 561 562 VSYNC ~ ~ 561 562 563 564 565 566 567 568 ~ 192 HSYNC 560 ~ 2640 clocks 1320 528 ~ ~ ~ Data Enable ~ 540 Active Vertical Lines per field Field 2: 23 Vertical Blanking Lines 569 570 582 583 584 1123 1124 1125 VSYNC Figure 4-21: H:V:DE Output Timing 1920 x 1080i @ 50 (Format 20) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 53 of 145 1728 Total Horizontal Clocks per line Data Enable 288 126 24 1440 Clocks for Active Video 138 clocks HSYNC ~ ~ ~ ~ ~ Data Enable ~ 288 Active Vertical Lines per field Field 1: 24 Vertical Blanking Lines 1728 clocks 264 ~~ 24 HSYNC 623 624 625 1 2 3 4 5 6 7 22 23 310 311 312 VSYNC ~ ~ 288 Active Vertical Lines per field Field 2: 25 Vertical Blanking Lines ~ ~ Data Enable 24 1728 clocks 864 264 HSYNC 310 311 312 313 314 315 316 317 318 319 320 335 336 623 624 625 VSYNC Figure 4-22: H:V:DE Output Timing 720 (1440) x 576 @ 50 (Format 21 & 22) 2200 Total Horizontal Clocks per line Data Enable 88 280 1920 Clocks for Active Video 44 148 clocks HSYNC Progressive Frame: 45 Vertical Blanking Lines ~ ~ ~ ~ ~ ~ Data Enable 1080 Active Vertical Lines 2200 clocks 192 ~ HSYNC 1121 1122 1123 1124 1125 1 2 3 4 5 6 7 41 42 ~ ~ 88 1121 1122 1123 1124 1125 VSYNC Figure 4-23: H:V:DE Output Timing 1920 x 1080p @ 59.94/60 (Format 16) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 54 of 145 2640 Total Horizontal Clocks per line Data Enable 720 44 528 1920 Clocks for Active Video 148 clocks HSYNC ~ ~ ~ ~ ~ Data Enable ~ 1080 Active Vertical Lines Progressive Frame: 45 Vertical Blanking Lines 2640 clocks 192 ~ HSYNC 1121 1122 1123 1124 1125 1 2 3 4 5 6 7 41 42 ~ ~ 528 1121 1122 1123 1124 1125 VSYNC Figure 4-24: H:V:DE Output Timing 1920 x 1080p @ 50 (Format 31) 2750 Total Horizontal Clocks per line Data Enable 830 44 638 1920 Clocks for Active Video 148 clocks HSYNC Progressive Frame: 45 Vertical Blanking Lines ~ ~ ~ ~ ~ ~ Data Enable 1080 Active Vertical Lines 2750 clocks 192 ~ HSYNC 1121 1122 1123 1124 1125 1 2 3 4 5 6 7 41 42 ~ ~ 638 1121 1122 1123 1124 1125 VSYNC Figure 4-25: H:V:DE Output Timing 1920 x 1080p @ 23.94/24 (Format 32) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 55 of 145 2640 Total Horizontal Clocks per line Data Enable 720 44 528 1920 Clocks for Active Video 148 clocks HSYNC Progressive Frame: 45 Vertical Blanking Lines ~ ~ ~ ~ ~ ~ Data Enable 1080 Active Vertical Lines 2640 clocks 192 ~ HSYNC 1121 1122 1123 1124 1125 1 2 3 4 5 6 7 41 42 ~ ~ 528 1121 1122 1123 1124 1125 VSYNC Figure 4-26: H:V:DE Output Timing 1920 x 1080p @ 25 (Format 33) 2200 Total Horizontal Clocks per line Data Enable 280 44 88 1920 Clocks for Active Video 148 clocks HSYNC Progressive Frame: 45 Vertical Blanking Lines ~ ~ ~ 2220 clocks ~ 1 2 3 4 5 6 7 41 42 ~ ~ 192 HSYNC 1121 1122 1123 1124 1125 ~ 88 ~ ~ Data Enable 1080 Active Vertical Lines 1121 1122 1123 1124 1125 VSYNC Figure 4-27: H:V:DE Output Timing 1920 x 1080p @ 29.97/30 (Format 34) 4.13 Automatic Video Standards Detection Using the timing extracted from the received TRS signals, the GS2970 is able to identify the received video standard. In 3G input mode, the GS2970 measures the timing parameters of one of the two identical data streams. The Rate Selection/Indication bits and the VD_STD code may be used in combination to determine the video standard. The total samples per line, active samples per line, total lines per field/frame and active lines per field/frame are all measured. Four registers are provided to allow the system to read the video standard information from the device. These raster structure registers are provided in addition to the GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 56 of 145 VIDEO_FORMAT_352_A_X and VIDEO_FORMAT_352_B_X registers, and are updated once per frame at the end of line 12. The raster structure registers also contain three status bits: STD_LOCK, INT/PROG and M. The STD_LOCK bit is set HIGH whenever the timing signal generator is fully synchronized to the incoming standard, and detects it as one of the supported formats. The INT/PROG bit is set HIGH if the detected video standard is interlaced and LOW if the detected video standard is progressive. M is set HIGH if the clock frequency includes the "1000/1001" factor denoting a 23.98, 29.97 or 59.94Hz frame rate. The video standard code is reported in the VD_STD bits of the host interface register. Table 4-11 describes the 5-bit codes for the recognized video standards. Table 4-11: Supported Video Standard Codes SMPTE Standard Active Video Area RATE_ DET[1] HD/3G RATE_ DET[0] SD/HD Lines per Frame Active Lines per Frame Words per Active Line Words per Line VD_STD [5:0] 425M (3G) 4:2:2 1920x1080/60 (1:1) 1 0 1125 1080 1920 2200 2Bh 1920x1080/50 (1:1) 1 0 1125 1080 1920 2640 2Dh 425M (3G) 4:4:4 1920x1080/60 (2:1) or 1920x1080/30 (PsF) 1 0 1125 1080 3840 4400 2Ah 1920x1080/50 (2:1) or 1920x1080/25 (PsF) 1 0 1125 1080 3840 5280 2Ch 1280x720/60 (1:1) 1 0 750 720 2560 3300 20h 1280x720/50 (1:1) 1 0 750 720 2560 3960 24h 1920x1080/30 (1:1) 1 0 1125 1080 3840 4400 2Bh 1920x1080/25 (1:1) 1 0 1125 1080 3840 5280 2Dh 1280x720/25 (1:1) 1 0 750 720 2560 7920 26h 1920x1080/24 (1:1) 1 0 1125 1080 3840 5500 30h 1280x720/24 (1:1) 1 0 750 720 2560 8250 28h 260M (HD) 1920x1035/60 (2:1) 0 0 1125 1035 1920 2200 15h 259M (HD) 1920x1080/50 (2:1) 0 0 1250 1080 1920 2376 14h GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 57 of 145 Table 4-11: Supported Video Standard Codes (Continued) SMPTE Standard Active Video Area RATE_ DET[1] HD/3G RATE_ DET[0] SD/HD Lines per Frame Active Lines per Frame Words per Active Line Words per Line VD_STD [5:0] 274M (HD) 1920x1080/60 (2:1) or 1920x1080/30 (PsF) 0 0 1125 1080 1920 2200 0Ah 1920x1080/50 (2:1) or 1920x1080/25 (PsF) 0 0 1125 1080 1920 2640 0Ch 1920x1080/30 (1:1) 0 0 1125 1080 1920 2200 0Bh 1920x1080/25 (1:1) 0 0 1125 1080 1920 2640 0Dh 1920x1080/24 (1:1) 0 0 1125 1080 1920 2750 10h 1920x1080/24 (PsF) 0 0 1125 1080 1920 2750 11h 1920x1080/25 (1:1) - 0 0 1125 1080 2304 2640 0Eh 1920x1080/25 (PsF) - EM 0 0 1125 1080 2304 2640 0Fh 1920x1080/24 (1:1) - 0 0 1125 1080 2400 2750 12h 1920x1080/24 (PsF) - EM 0 0 1125 1080 2400 2750 13h 1280x720/30 (1:1) 0 0 750 720 1280 3300 02h 1280x720/30 (1:1) - EM 0 0 750 720 2880 3300 03h 1280x720/50 (1:1) 0 0 750 720 1280 1980 04h 1280x720/50 (1:1) - EM 0 0 750 720 1728 1980 05h 1280x720/25 (1:1) 0 0 750 720 1280 3960 06h 1280x720/25 (1:1) - EM 0 0 750 720 3456 3960 07h 1280x720/24 (1:1) 0 0 750 720 1280 4125 08h 1280x720/24 (1:1) - EM 0 0 750 720 3600 4125 09h 1280x720/60 (1:1) 0 0 750 720 1280 1650 00h 1280x720/60 (1:1) - EM 0 0 750 720 1440 1650 01h 1440x487/60 (2:1) x 1 525 244 or 243 1440 1716 16h 1440x507/60 x 1 525 254 or 253 1440 1716 17h 525-line 487 generic x 1 525 - - 1716 19h 525-line 507 generic x 1 525 - - 1716 1Bh 1440x576/50 (2:1) Or dual link progressive) x 1 625 - 1440 1728 18h 625-line generic x 1 625 - - 1728 1Ah 296M (HD) 296M (HD) 125M (SD) ITU-R BT.656 (SD) GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 58 of 145 Table 4-11: Supported Video Standard Codes (Continued) SMPTE Standard Active Video Area RATE_ DET[1] HD/3G RATE_ DET[0] SD/HD Lines per Frame Active Lines per Frame Words per Active Line Words per Line VD_STD [5:0] Unknown HD SD/HD = 0 0 0 - - - - 1Dh Unknown SD SD/HD = 1 x 1 - - - - 1Eh Unknown 3G SD/HD = 0 1 0 - - - - 3Ch Notes: 1. The Line Numbers in brackets refer to version zero SMPTE 352M packet locations, if they are different from version 1. 2. The part may provide full or limited functionality with standards that are not included in this table. Please consult a Semtech technical representative. 3. For SD-SDI streams, the device can report an incorrect M value when SMPTE-352M packets are present. NOTE: In certain systems, due to greater ppm offsets in the crystal, the `M' bit may not assert properly. In such cases, bits 3:0 in Register 06Fh can be increased to a maximum value of 4. By default (after power up or after systems reset), the four RASTER_STRUCTURE, VD_STD, STD_LOCK and INT/PROG fields are set to zero. These fields are also cleared when the SMPTE_BYPASS pin is LOW. 4.14 Data Format Detection & Indication In addition to detecting the video standard, the GS2970 detects the data format, i.e. SDTI, SDI, TDM data (SMPTE 346M), etc. This information is represented by bits in the DATA_FORMAT_DSX register accessible through the host interface. Data format detection is only carried out when the LOCKED signal is HIGH. By default (at power up or after system reset), the DATA_FORMAT_DSX register is set to Fh (undefined). This register is also set as undefined when the LOCKED signal is LOW and/or the SMPTE_BYPASS pin is LOW. Table 4-12: Data Format Register Codes YDATA_FORMAT[3:0] or CDATA_FORMAT[3:0] Data Format Remarks 0h ~ 05h SDTI SMPTE 321M, SMPTE 322M, SMPTE 326M 6h SDI - 7h Reserved - 8h TDM SMPTE 346M GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 59 of 145 Table 4-12: Data Format Register Codes (Continued) YDATA_FORMAT[3:0] or CDATA_FORMAT[3:0] Data Format Remarks 9h HD-SDTI - Ah ~ Eh Reserved - Fh Non-SMPTE data format Detected data format is not SMPTE. SMPTE_BYPASS = LOW or LOCKED = LOW The data format is determined using the following criteria: * If TRS ID words are detected but no SDTI header or TDM header is detected, then the data format is SDI * If TRS ID words are detected and the SDTI header is available then the format is SDTI * If TRS ID words are detected and the TDM data header is detected then the format is TDM video * No TRS words are detected, but the PLL is locked, then the data format is unknown NOTE: Two data format sets are provided for HD video rates. This is because the Y and Cr/Cb channels can be used separately to carry SDTI data streams of different data formats. In SD video mode only the Y data format register contains the data, and the C register is set to Fh (undefined format). 4.15 EDH Detection 4.15.1 EDH Packet Detection The GS2970 determines if EDH packets are present in the incoming video data and asserts the EDH_DETECT status according to the SMPTE standard. EDH_DETECT is set HIGH when EDH packets have been detected and remains HIGH until EDH packets are no longer present. It is set LOW at the end of the vertical blanking (falling edge of V) if an EDH packet has not been detected during vertical blanking. EDH_DETECT can be programmed to be output on the multi-function output port pins. The EDH_DETECT bit is also available in the host interface. 4.15.2 EDH Flag Detection The EDH flags for ancillary data, active picture, and full field regions are extracted from the detected EDH packets and placed in the EDH_FLAG_IN register. When the EDH_FLAG_UPDATE_MASK bit in the host interface is set HIGH, the GS2970 updates the Ancillary Data, Full Field, and Active Picture EDH flags according to SMPTE RP165. The updated EDH flags are available in the EDH_FLAG_OUT register. The EDH packet output from the device contains these updated flags. One set of flags is provided for both fields 1 and 2. The field 1 flag data is overwritten by the field 2 flag data. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 60 of 145 When EDH packets are not detected, the UES flags in the EDH_FLAG_OUT register are set HIGH to signify that the received signal does not support Error Detection and Handling. In addition, the EDH_DETECT bit is set LOW. These flags are set regardless of the setting of the EDH_FLAG_UPDATE_MASK bit. EDH_FLAG_OUT and EDH_FLAG_IN may be read via the host interface at any time during the received frame except on the lines defined in SMPTE RP165, when these flags are updated. The GS2970 indicates the CRC validity for both active picture and full field CRCs. The AP_CRC_V bit in the host interface indicates the active picture CRC validity, and the FF_CRC_V bit indicates the full field CRC validity. When EDH_DETECT = LOW, these bits are cleared. The EDH_FLAG_OUT and EDH_FLAG_IN register values remain set until overwritten by the decoded flags in the next received EDH packet. When an EDH packet is not detected during vertical blanking, the flag registers are cleared at the end of the vertical blanking period. 4.16 Video Signal Error Detection & Indication The GS2970 includes a number of video signal error detection functions. These are provided to enhance operation of the device when operating in SMPTE mode (SMPTE_BYPASS = HIGH). These features are not available in the other operating modes of the device (i.e. when SMPTE_BYPASS = LOW). Signal errors that can be detected include: 1. TRS errors. 2. HD line based CRC errors. 3. EDH errors. 4. HD line number errors. 5. Video standard errors. The device maintains an ERROR_STAT_X register. Each error condition has a specific flag in the ERROR_STAT_X register, which is set HIGH whenever an error condition is detected. An ERROR_MASK register is also provided, allowing the user to select which error conditions are reported. Each bit of the ERROR_MASK register corresponds to a unique error type. Separate SD_AUDIO_ERROR_MASK and HD_AUDIO_ERROR_MASK registers for SD and HD audio cores are also provided, allowing select error conditions to be reported. Each bit of each ERROR_MASK register corresponds to a unique error type. By default (at power up or after system reset), all bits of the ERROR_MASK registers are zero, enabling all errors to be reported. Individual error detection may be disabled by setting the corresponding bit HIGH in the mask registers. Error conditions are indicated by a VIDEO _ERROR signal and an AUDIO_ERROR signal, which are available for output on the multifunction I/O output pins. The two signals are also combined into a summary DATA_ERROR signal, which is also available on the GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 61 of 145 multifunction I/O pins. These signals are normally HIGH, but are set LOW by the device when an error condition has been detected. These signals are a logical 'NOR' of the appropriate error status flags stored in the ERROR_STAT_X register, which are gated by the bit settings in the ERROR_MASK registers. When an error status bit is HIGH and the corresponding error mask bit is LOW, the corresponding DATA_ERROR signal is set LOW by the device. The ERROR_STAT_X registers, and correspondingly the DATA_ERROR, VIDEO_ERROR, and AUDIO_ERROR signals, are cleared at the start of the next video field or when read via the host interface, which ever condition occurs first. Note that any AUDIO_ERROR condition will cause DATA_ERROR to assert. Use the SD_AUDIO_ERROR_MASK and HD_AUDIO_ERROR_MASK registers if masking these events is desired. All bits of the ERROR_STAT_X registers are also cleared under any of the following conditions: 1. LOCKED signal = LOW. 2. SMPTE_BYPASS = LOW. 3. When a change in video standard has been detected. 4. RESET_TRST = LOW Table 4-13 shows the ERROR_STAT_X register and ERROR_MASK_X register. NOTE: Since the error indication registers are cleared once per field, if an external host micro is polling the error registers periodically, an error flag may be missed if it is intermittent, and the polling frequency is less than the field rate. Table 4-13: Error Status Register and Error Mask Register Video Error Status Register Video Error Mask Register SAV_ERR (02h, 03h) SAV_ERR_MASK (037h, 038h) EAV_ERR (02h, 03h) EAV_ERR_MASK (037h, 038h) YCRC_ERR (02h, 03h) YCRC_ERR_MASK (037h, 038h) CCRC_ERR (02h, 03h) CCRC_ERR_MASK (037h, 038h) LNUM_ERR (02h, 03h) LNUM_ERR_MASK (037h, 038h) YCS_ERR (02h, 03h) YCS_ERR_MASK (037h, 038h) CCS_ERR (02h, 03h) CCS_ERR_MASK (037h, 038h) AP_CRC_ERR (02h) AP_CRC_ERR_MASK (037h) FF_CRC_ERR (02h) FF_CRC_ERR_MASK (037h) VD_STD_ERR (02h, 03h) VD_STD_ERR_MASK (037h) NOTE 1: See Section 4.19 for Audio Error Status. NOTE 2: In 3G Level B mode, separate Video Error Mask registers exist for Link A and Link B. The GS2970 distinguishes between Level A and Level B mappings at 3Gb/s. When Level B data is detected, error detection is enabled separately for Data Stream 1 and Data Stream 2 (Link A and Link B, respectively). Therefore, a second set of error GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 62 of 145 status and mask registers is available for Data Stream 2, and is only valid when 3Gb/s Level B data is detected by the device. 4.16.1 TRS Error Detection TRS error flags are generated by the GS2970 under the following two conditions: 1. A phase shift in received TRS timing is observed on a non-switching line. 2. The received TRS Hamming codes are incorrect. Both SAV and EAV TRS words are checked for timing and data integrity errors. For HD mode, only the Y channel TRS codes are checked for errors. For 3G mode Level A signals, only data stream one TRS codes are checked for errors. For 3G Level B signals, the Y channel TRS codes of both Link A and Link B are checked for errors. Both 8-bit and 10-bit TRS code words are checked for errors. The SAV_ERR bit of the ERROR_STAT_X register is set HIGH when an SAV TRS error is detected. The EAV_ERR bit of the ERROR_STAT_X register is set HIGH when an EAV TRS error is detected. 4.16.2 Line Based CRC Error Detection The GS2970 calculates line based CRCs for HD and 3G video signals. CRC calculations are done for each 10-bit channel (Y and C for HD video, DS1 and DS2 for 3G video). These calculated CRC values are compared with the received CRC values. If a mismatch in the calculated and received CRC values is detected for Y channel data (Data Stream 1 for 3G video), the YCRC_ERR bit in the ERROR_STAT_X register is set HIGH. If a mismatch in the calculated and received CRC values is detected for C channel data (Data Stream 2 for 3G video), the CCRC_ERR bit in the ERROR_STAT_X register is set HIGH. Y or C CRC errors are also generated if CRC values are not embedded. Line based CRC errors are only generated when the device is operating in HD and 3G modes. NOTE: By default, 8-bit to 10-bit TRS remapping is enabled. If an 8-bit input is used, the HD CRC check is based on the 10-bit remapped value, not the 8-bit value, so the CRC Error Flag is incorrectly asserted and should be ignored. If 8-bit to 10-bit remapping is enabled, then CRC correction and insertion should be enabled by setting the CRC_INS_MASK bit in the IOPROC_DISABLE register LOW. This ensures that the CRC values are updated. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 63 of 145 4.16.3 EDH CRC Error Detection The GS2970 also calculates Full Field (FF) and Active Picture (AP) CRC's according to SMPTE RP165 in support of Error Detection and Handling packets in SD signals. These calculated CRC values are compared with the received CRC values. Error flags for AP and FF CRC errors are provided and each error flag is a logical OR of field 1 and field 2 error conditions. The AP_CRC_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH when an Active Picture CRC mismatch has been detected in field 1 or 2. The FF_CRC_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH when a Full Field CRC mismatch has been detected in field 1 or 2. EDH CRC errors are only indicated when the device is operating in SD mode and when the device has correctly received EDH packets. 4.16.4 HD & 3G Line Number Error Detection If a mismatch in the calculated and received line numbers is detected, the LNUM_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH. 4.17 Ancillary Data Detection & Indication The GS2970 detects ancillary data in both the vertical and horizontal ancillary data spaces. Status signal outputs Y/1ANC and C/2ANC are provided to indicate the position of ancillary data in the output data streams. These signals may be selected for output on the multi-function I/O port pins (STAT[5:0]). The GS2970 indicates the presence of all types of ancillary data by detecting the 000h, 3FFh, 3FFh (00h, FFh, FFh for 8-bit video) ancillary data preamble. NOTE: Both 8 and 10-bit ancillary data preambles are detected by the device. By default (at power up or after system reset) the GS2970 indicates all types of ancillary data. Up to 5 types of ancillary data can be specifically programmed for recognition. For HD video signals, ancillary data may be placed in both the Y and Cb/Cr video data streams separately. For SD video signals, the ancillary data is multiplexed and combined into the YCbCr data space. For 3G signals, ancillary data may be placed in either or both of the virtual interface data streams. Both data streams are examined for ancillary data. For a 3G data stream formatted as per Level A mapping: * The ancillary data is placed in Data Stream 1 first, with overflow into Data Stream 2 * SMPTE 352M packets are duplicated in both data streams For a 3G data stream formatted as per Level B mapping: * Each multiplexed data stream forming the 3G signal contains ancillary data embedded according to SMPTE 291M * Each multiplexed data stream forming the 3G signal contains SMPTE 352M packets embedded according to SMPTE 425M GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 64 of 145 When operating in HD mode, the Y/1ANC signal is HIGH whenever ancillary data is detected in the Luma data stream, and C/2ANC is HIGH whenever ancillary data is detected in the Chroma data stream. The signals are asserted HIGH at the start of the ancillary data preamble, and remain HIGH until after the ancillary data checksum. When detecting ancillary data in 3G Level A data, the Y/1ANC status output is HIGH whenever Data Stream 1 ancillary data is detected and the C/2ANC status output is HIGH whenever Data Stream 2 ancillary data is detected. When detecting ancillary data in 3G Level B data, the Y/1ANC status output is HIGH whenever Data Stream 1 ancillary data is detected on either Y or C channels and the C/2ANC status output is HIGH whenever Data Stream 2 ancillary data is detected on either Y or C channels. When operating in SD mode, the Y/1ANC and C/2ANC signals depend on the output data format. For 20-bit demultiplexed data, the Y/1ANC and C/2ANC signals operate independently to indicate the first and last ancillary Data Word position in the Luma and/or Chroma data streams. For 10-bit multiplexed data, the Y/1ANC signal is HIGH whenever ancillary data is detected, and the C/2ANC signal is always LOW. When operating in 3G modes, the Y/1ANC and C/2ANC flags are both zero if the 10-bit multiplexed output format is selected. These status signal outputs are synchronous with PCLK and may be used as clock-enables for external logic, or as write-enables for an external FIFO or other memory devices. The operation of the Y/1ANC and C/2ANC signals is shown below in Figure 4-28. NOTE 1: When I/O processing is disabled, the Y/1ANC and C/2ANC flags may toggle, but they are invalid and should be ignored. NOTE 2: In 3G Level B mode, if the ANC_EXT_SEL_DS2_DS1 bit is HIGH and the ANC_DATA_DELETE bit is HIGH, the Y/1ANC and C/2ANC flags are not valid. NOTE 3: For 3G Level B data, the Y/1ANC flag identifies all ANC data on Data Stream 1 (Link A), whether it is embedded in the Y or C component - ANC data is not identified separately for each component. Similarly, the C/2ANC flag identifies all ANC data on Data Stream 2 (Link B), whether it is embedded in the Y or C component. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 65 of 145 PC LK LU M A D ATA O U T 000 3FF 3FF D ID DBN DC ANC DATA CSUM BLANK BLAN K CHRO M A DATA O UT 000 3FF 3FF D ID DBN DC ANC DATA ANC DATA ANC DATA CSUM Y/1ANC C/2ANC A N C D A T A D E T E C T IO N - H D T V 2 0 B IT O U T P U T M O D E PC LK M U L T IP L E X E D Y 'C b C r 000 000 3FF 3FF 3FF 3FF Y D ID CANC YCSUM CCSUM Y/1ANC C/2ANC A N C D A T A D E T E C T IO N - H D T V 1 0 B IT O U T P U T M O D E PC LK LU M A D ATA O U T CHRO M A DATA O UT BLAN K 3FF D ID DC ANC DATA ANC DATA ANC DATA CSUM BLAN K 000 3FF DBN ANC DATA ANC DATA ANC DATA ANC DATA BLAN K BLAN K Y/1ANC C/2ANC A N C D A T A D E T E C T IO N - S D T V 2 0 B IT O U T P U T M O D E PC LK M U L T IP L E X E D Y 'C b C r 000 3FF 3FF D ID DBN DC ANC DATA ANC DATA CSUM BLANK Y/1ANC A N C D A T A D E T E C T IO N - S D T V 1 0 B IT O U T P U T M O D E Figure 4-28: Y/1ANC and C/2ANC Signal Timing 4.17.1 Programmable Ancillary Data Detection As described above in Section 4.17, the GS2970 detects and indicates all ancillary data types by default. It is possible to program which ancillary data types are to be detected and indicated. Up to 5 different ancillary data types may be programmed for detection by the GS2970 in the ANC_TYPE_DS1 registers for SD, HD and 3G Level A data. When so programmed, the GS2970 only indicates the presence of the specified ancillary data types, ignoring all other ancillary data. For each data type to be detected, the user must program the DID and/or SDID of that ancillary data type. In the case where no DID or SDID values are programmed, the GS2970 indicates the presence of all ancillary data. In the case where one or more, DID and/or SDID values have been programmed, then only those matching data types are detected and indicated. The timing of the Y/1ANC and C/2ANC signals in this case is as shown in Figure 4-28. The GS2970 compares the received DID and/or SDID with the programmed values. If a match is found, ancillary data is indicated. For any DID or SDID value set to zero, no comparison or match is made. For example, if the DID is programmed and the SDID is not programmed, the GS2970 only detects a match to the DID value. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 66 of 145 If both DID and SDID values are non-zero, then the received ancillary data type must match both the DID and SDID before Y/1ANC and/or C/2ANC is set HIGH. NOTE 1: For 3G Level B data, the ANC_TYPE_DS1 registers are valid for Data Stream 1, and a second set of five ANC_TYPE registers (ANC_TYPE_DS2) is provided for detection of specific ancillary data in Data Stream 2. NOTE 2: SMPTE 352M Payload Identifier packets and Error Detection and Handling (EDH) Packets are always detected by the GS2970, irrespective of the settings of the ANC_TYPE registers. 4.17.2 SMPTE 352M Payload Identifier The GS2970 automatically extracts the SMPTE 352M payload identifier present in the input data stream for SD, HD, and 3G Level A signals. The four word payload identifier packets are written to VIDEO_FORMAT_X_DS1 and VIDEO_FORMAT_X_DS2 bits accessible through the host interface. The device also indicates the version of the payload packet in the VERSION_352M bit of the DATA_FORMAT_DSX register. When the SMPTE 352M packet is formatted as a "version 1" packet, the VERSION_352M bit is set HIGH, when the packet is formatted as a "version 2" packet, this bit is set LOW. The VIDEO_FORMAT_352_A_X and VIDEO_FORMAT_352_B_X registers are only updated if there are no checksum errors in the received SMPTE 352M packets. By default (at power up or after system reset), the VIDEO_FORMAT_X_DS1 and VIDEO_FORMAT_X_DS2 bits are set to 0, indicating an undefined format. NOTE 1: When 3G Level B data is detected by the device, the user needs to extract the SMPTE 352M Payload Identifier packets by using the ANC packet extraction block - they are not detected and extracted automatically. In this case: * The VD_STD_ERR bit is not valid * 352M extraction is only done on one data stream or the other, not both simultaneously (Link A or Link B selected via the host interface) * Previously embedded 352M packets can be deleted on one data stream only (using the ANC_DATA_DELETE bit, see Section 4.18.8), but these packets are replaced with 10-bit Y/C blanking values only * It is necessary to manually extract the SMPTE 352M data by programming the DID, SDID and line number information into the ANC data extraction block NOTE 2: SMPTE 352M packet regeneration is enabled by default for 3G Level B inputs, and should be disabled through the host interface if Level B to Level A conversion is not enabled. 4.17.2.1 SMPTE 352M Payload Identifier Usage The SMPTE 352M Payload Identifier is used to confirm the video format identified by the Automatic Video Standards Detection block (see Section 4.17.4). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 67 of 145 Table 4-14: SMPTE 352M Packet Data Bit Name VIDEO_FORMAT_4_DS1 Bit Name Description R/W Default 15-8 SMPTE 352M Byte 4 Data is available in this register when Video Payload Identification Packets are detected in the data stream. R 0 7-0 SMPTE 352M Byte 3 R 0 15-8 SMPTE 352M Byte 2 R 0 7-0 SMPTE 352M Byte 1 R 0 Address: 01Ah VIDEO_FORMAT_3_DS1 Address: 01Ah VIDEO_FORMAT_2_DS1 Address: 019h VIDEO_FORMAT_2_DS1 Address: 019h 4.17.2.2 3G SMPTE 352M Packets Following Level B to Level A Conversion After Level B to Level A conversion, modified payload data must be programmed via the host interface into the VIDEO_FORMAT_352_X_X registers and automatically inserted by the GS2970 on the correct SMPTE 352M Line Number. SMPTE 352M Packets are embedded in both data streams. Previously embedded 352M packets may be deleted from one data stream only (using the ANC_DATA_DELETE bit, see Section 4.18.8), but these packets are replaced with 10-bit Y/C blanking values. NOTE: Pre-existing SMPTE 352M Packets that are not deleted are re-mapped to different line numbers during conversion to Level A formatting. These packets should be ignored by the system, since they are on non-standard SMPTE 352M lines. 4.17.3 Ancillary Data Checksum Error The GS2970 calculates checksums for all received ancillary data. These calculated checksums are compared with the received ancillary data checksum words. If a mismatch in the calculated and received checksums is detected, then a checksum error is indicated. When operating in HD mode, the device makes comparisons on both the Y and C channels separately. If an error condition in the Y channel is detected, the YCS_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH. If an error condition in the C channel is detected, the CCS_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH. When operating in 3G Level A mode, the device makes comparisons on both the Y (Data Stream 1) and C (Data Stream 2) channels separately. If an error condition in the Y channel is detected, the YCS_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH. If an error condition in the C channel is detected, the CCS_ERR bit in the VIDEO_ERROR_STAT_X register is set HIGH. When operating in 3G Level B mode, the device makes comparisons on both the Y channel and the C channel of both Link A and Link B. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 68 of 145 When operating in SD mode, only the YCS_ERR bit is set HIGH when checksum errors are detected. 4.17.3.1 Programmable Ancillary Data Checksum Calculation As described above, the GS2970 calculates and compares checksum values for all ancillary data types by default. It is possible to program which ancillary data types are checked as described in Section 4.17.1. When so programmed, the GS2970 only checks ancillary data checksums for the specified data types, ignoring all other ancillary data. The YCS_ERR and/or CCS_ERR bits in the VIDEO_ERROR_STAT_X register are only set HIGH if an error condition is detected for the programmed ancillary data types. 4.17.4 Video Standard Error If a mismatch between the received SMPTE 352M packets and the calculated video standard occurs, the GS2970 indicates a video standard error by setting the VD_STD_ERR bit of the VIDEO_ERROR_STAT_X register HIGH. The device detects the SMPTE 352M Packet version as defined in the SMPTE 352M standard. If the incoming packet is Version Zero, then no comparison is made with the internally generated payload information and the VD_STD_ERR bit is not set HIGH. NOTE 1: If the received SMPTE 352M packet indicates 25, 30 or 29.97PsF formats, the device only indicates an error when the video format is actually progressive. The device detects 24 and 23.98PsF video standards and perform error checking at these rates. NOTE 2: The VD_STD_ERR bit should be ignored in all 3G modes. NOTE 3: VD_STD_ERR_DS1 is set incorrectly for a 1920x1080/PsF/24 payload ID. To resolve this issue, choose one of the two methods. * Set the VD_STD_ERR_DS1 mask bit high in the ERROR_MASK_1 register to avoid having incorrect assertion of the DATA_ERROR pin. * Monitor the received SMPTE ST0352 packet in the VIDEO_FORMAT_352_A_1 and VIDEO_FORMAT_352_B_1 registers and compare that to the video format identified in the VD_STD_DS1 bits in the DATA_FORMAT_DS1 register. Then, make the determination of whether or not there is a mismatch on their own. 4.18 Signal Processing In addition to error detection and indication, the GS2970 can also correct errors, inserting corrected code words, checksums and CRC values into the data stream. The following processing can be performed by the GS2970: 1. TRS error correction and insertion. 2. HD line based CRC correction and insertion. 3. EDH CRC error correction and insertion. 4. HD line number error correction and insertion. 5. Illegal code re-mapping. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 69 of 145 6. Ancillary data checksum error correction and insertion. 7. Audio extraction. 8. SMPTE 372M (Level B to Level A) Conversion. All of the above features are only available in SMPTE mode (SMPTE_BYPASS = HIGH). To enable these features, the IOPROC_EN/DIS pin must be set HIGH, and the individual feature must be enabled via bits in the IOPROC_DISABLE register. The IOPROC_DISABLE register contains one bit for each processing feature allowing each one to be enabled/disabled individually. By default (at power up or after system reset), all of the IOPROC_DISABLE register bits are LOW, enabling all of the processing features. To disable an individual processing feature, set the corresponding IOPROC_DISABLE bit HIGH in the IOPROC_DISABLE register. Table 4-15: IOPROC_DISABLE Register Bits Processing Feature IOPROC_DISABLE Register Bit TRS error correction and insertion TRS_INS Y and C line based CRC error correction CRC_INS Y and C line number error correction LNUM_INS Ancillary data check sum correction ANC_CHECKSUM_INSERTION EDH CRC error correction EDH_CRC_INS Illegal code re-mapping ILLEGAL_WORD_REMAP H timing signal configuration H_CONFIG Update EDH Flags EDH_FLAG_UPDATE Audio Data Extraction AUDIO_SEL Ancillary Data Extraction ANC_DATA_EXT Audio Extraction AUD_EXT Regeneration of 352M packets REGEN_352M 4.18.1 TRS Correction & Insertion When TRS Error Correction and Insertion is enabled, the GS2970 generates and overwrites TRS code words as required. TRS Word Generation and Insertion is performed using the timing generated by the Timing Signal Generator, providing an element of noise immunity over using just the received TRS information. This feature is enabled when the IOPROC_EN/DIS pin is HIGH and the TRS_INS_DISABLE bit in the IOPROC_DISABLE register is set LOW. NOTE: Inserted TRS code words are always 10-bit compliant, irrespective of the bit depth of the incoming video stream. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 70 of 145 4.18.2 Line Based CRC Correction & Insertion When CRC Error Correction and Insertion is enabled, the GS2970 generates and inserts line based CRC words into both the Y and C channels of the data stream. Line based CRC word generation and insertion only occurs in HD and 3G modes, and is enabled in when the IOPROC_EN/DIS pin is HIGH and the CRC_INS_DSX_MASK bit in the IOPROC_X register is set LOW. 4.18.3 Line Number Error Correction & Insertion When Line Number Error Correction and Insertion is enabled, the GS2970 calculates and inserts line numbers into the output data stream. Re-calculated line numbers are inserted into both the Y and C channels. Line number generation is in accordance with the relevant HD or 3G video standard as determined by the Automatic Standards Detection block. This feature is enabled when the device is operating in HD or 3G modes, the IOPROC_EN/DIS pin is HIGH and the LNUM_INS_DSX_MASK bit in the IOPROC_X register is set LOW. 4.18.4 ANC Data Checksum Error Correction & Insertion When ANC data Checksum Error Correction and Insertion is enabled, the GS2970 generates and inserts ancillary data checksums for all ancillary data words by default. Where user specified ancillary data has been programmed (see Section 4.17.1), only the checksums for the programmed ancillary data are corrected. This feature is enabled when the IOPROC_EN/DIS pin is HIGH and the ANC_CHECKSUM_INSERTION_DSX_MASK bit in the IOPROC_X register is set LOW. 4.18.5 EDH CRC Correction & Insertion When EDH CRC Error Correction and Insertion is enabled, the GS2970 generates and overwrites full field and active picture CRC check-words. Additionally, the device sets the active picture and full field CRC 'V' bits HIGH in the EDH packet. The AP_CRC_V and FF_CRC_V register bits only report the received EDH validity flags. EDH FF and AP CRC's are only inserted when the device is operating in SD mode, and if the EDH data packet is detected in the received video data. Although the GS2970 modifies and inserts EDH CRC's and EDH packet checksums, EDH error flags are only updated when the EDH_FLAG_UPDATE_MASK bit is LOW. This feature is enabled in SD mode, when the IOPROC_EN/DIS pin is HIGH and the EDH_CRC_INS_MASK bit in the IOPROC_1 register is set LOW. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 71 of 145 4.18.6 Illegal Word Re-mapping All words within the active picture (outside the horizontal and vertical blanking periods), between the values of 3FCh and 3FFh are re-mapped to 3FBh. All words within the active picture area between the values of 000h and 003h are remapped to 004h. This feature is enabled when the IOPROC_EN/DIS pin is HIGH and the ILLEGAL_WORD_REMAP_DSX_MASK bit in the IOPROC_X register is set LOW. 4.18.7 TRS and Ancillary Data Preamble Remapping 8-bit TRS and ancillary data preambles are re-mapped to 10-bit values. 8-bit to 10-bit mapping of TRS headers is only supported if the TRS values are 3FC 000 000. Other values such as 3FD, 3FE, 3FF, 001, 002 and 003 are not supported. This feature is enabled by default, and can be disabled via the IOPROC_X register. 4.18.8 Ancillary Data Extraction Ancillary data may be extracted externally from the GS2970 output stream using the Y/1ANC and C/2ANC signals, and external logic. As an alternative, the GS2970 includes a FIFO, which extracts ancillary data using read access via the host interface to ease system implementation. The FIFO stores up to 2048 x 16 bit words of ancillary data in two separate 1024 word memory banks. Data is accessed from both memory banks using the same host interface addresses, 800h to BFFh (see Table 4-32: ANC Extraction FIFO Access Registers). The device writes the contents of ANC packets into the FIFO, starting with the first Ancillary Data Flag (ADF), followed by up to 1024 words. All Data Identification (DID), Secondary Data Identification (SDID), Data Count (DC), user data, and checksum words are written into the device memory. The device detects ancillary data packet DID's placed anywhere in the video data stream, including the active picture area. In HD and 3G mode, ancillary data from the Y channel or Data Stream One is placed in the Least Significant Word (LSW) of the FIFO, allocated to the lower 8 bits of each FIFO address. Ancillary data from the C channel or Data Stream Two is placed in the Most Significant Word (MSW) (upper 8 bits) of each FIFO address. NOTE: Please refer to the ANC insertion and Extraction Application Note (Doc ID: 53410), for discrete steps and example of Ancillary data extraction. In SD mode, ancillary data is placed in the LSW of the FIFO. The MSW is set to zero. If the ANC_TYPE registers are all set to zero, the device extracts all types of ancillary data. If programmable ancillary data extraction is required, then up to five types of ancillary data to be extracted can be programmed in the ANC_TYPE registers (see Section 4.17.1). Additionally, the lines from which the packets are to be extracted can be programmed into the ANC_LINEA[10:0] and ANC_LINEB[10:0] registers, allowing ancillary data from a maximum of two lines per frame to be extracted. If only one line number register is GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 72 of 145 programmed (with the other set to zero), ancillary data packets are extracted from one line per frame only. When both registers are set to zero, the device extracts packets from all lines. To start Ancillary Data Extraction, the ANC_DATA_EXT_MASK bit of the host interface must be set LOW. Ancillary data packet extraction begins in the following frame (see Figure 4-29: Ancillary Data Extraction - Step A). Bank B Bank A Application Layer Read Pointer 0 ANC DATA 800h 0 800h BFFh 1023 BFFh ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA Internal Write Pointer 1023 ANC_DATA_SWITCH=LOW Figure 4-29: Ancillary Data Extraction - Step A Ancillary data is written into Bank A until full. The Y/1ANC and C/2ANC output flags can be used to determine the length of the ancillary data extracted and when to begin reading the extracted data from memory. While the ANC_DATA_EXT_MASK bit is set LOW, the ANC_DATA_SWITCH bit can be set HIGH during or after reading the extracted data. New data is then written into Bank B (up to 1024 x 16-bit words), at the corresponding host interface addresses (see Figure 4-30: Ancillary Data Extraction - Step B). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 73 of 145 Bank A 0 ANC DATA Bank B Internal Write Pointer 800h 0 800h 1023 BFFh ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA Application Layer Read Pointer ANC DATA ANC DATA BFFh 1023 ANC_DATA_SWITCH = HIGH Figure 4-30: Ancillary Data Extraction - Step B To read the new data, toggle the ANC_DATA_SWITCH bit LOW. The old data in Bank A is cleared to zero and extraction continues in Bank B (see Figure 4-31: Ancillary Data Extraction - Step C). Bank A 0 800h Bank B Application Layer Read Pointer 0 ANC DATA 800h ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA Internal Write Pointer 1023 BFFh 1023 BFFh ANC_DATA_SWITCH = LOW Figure 4-31: Ancillary Data Extraction - Step C GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 74 of 145 If the ANC_DATA_SWITCH bit is not toggled, extracted data is written into Bank B until full. To continue extraction in Bank A, the ANC_DATA_SWITCH bit must be toggled HIGH (see Figure 4-32: Ancillary Data Extraction - Step D). Bank B Bank A Internal Write Pointer 0 800h 0 ANC DATA 800h ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA ANC DATA Application Layer Read Pointer ANC DATA ANC DATA 1023 BFFh 1023 BFFh ANC_DATA_SWITCH = HIGH Figure 4-32: Ancillary Data Extraction - Step D Toggling the ANC_DATA_SWITCH bit LOW returns the process to step A (Figure 4-29). NOTE: Toggling the ANC_DATA_SWITCH must occur at a time when no extraction is taking place, i.e. when the both the Y/1ANC and C/2ANC signals are LOW. To turn extraction off, the ANC_DATA_EXT_MASK bit must be set HIGH. In HD mode, the device can detect ancillary data packets in the Luma video data only, Chroma video data only, or both. By default (at power-up or after a system reset) the device extracts ancillary data packets from the luma channel only. In 3G mode Level A, the device can detect ancillary data packets in Luma video (Data Stream One) only, Chroma video (Data Stream Two) only, or both. By default (at power-up or after a system reset) the device extracts ancillary data packets from Data Stream One only. In 3G mode Level B mode, the device can detect ancillary data packets in Luma video only, Chroma video only, or both from either Link A or Link B. Selection of Link A or Link B for ANC data extraction is done via the host interface. By default (at power-up or after a system reset) the device extracts ancillary data packets from Link A Luma only. To extract packets from the Chroma/Data Stream Two channel only, the HD_ANC_C2 bit of the host interface must be set HIGH. To extract packets from both Luma/Data Stream One and Chroma/Data Stream Two video data, the HD_ANC_Y1_C2 bit must be set HIGH (the setting of the HD_ANC_C2 bit is ignored). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 75 of 145 The default setting of both the HD_ANC_C2 and HD_ANC_Y1_C2 is LOW. The setting of these bits is ignored when the device is configured for SD video standards. Ancillary data packet extraction and deletion is disabled when the IOPROC_EN/DIS pin is set LOW. After extraction, the ancillary data may be deleted from the video stream by setting the ANC_DATA_DEL bit of the host interface HIGH. When set HIGH, all existing ancillary data is removed and replaced with blanking values. If any of the ANC_TYPE registers are programmed with a DID and/or DID and SDID, only the ancillary data packets with the matching IDs are deleted from the video stream. NOTE 1: After the ancillary data determined by the ANC_TYPE_X_APX registers has been deleted, other existing ancillary data may not be contiguous. The device does not concatenate the remaining ancillary data. NOTE 2: Reading extracted ancillary data from the host interface must be performed while there is a valid video signal present at the serial input and the device is locked (LOCKED signal is HIGH). 4.18.9 Level B to Level A Conversion When IOPROC_2 register bit LEVEL_B2A_CONV_DISABLE_MASK is HIGH (default), the GS2970 does not convert 3G LEVEL B streams between Level A and Level B mapping formats. When LEVEL_B2A_CONV_DISABLE_MASK is LOW, the GS2970 converts a 3G 1080p Level B stream to the Level A mapping format, as per SMPTE 425M. The device assumes that Link A and Link B are phase-aligned at the transmitter. The output data are line multiplexed such that the data content from Link A and Link B are assembled in a continuous fashion, at twice the input data rate. Extracted timing reference information is used to trigger a line counter which embeds the correct line number according to SMPTE 425M. The Level B/A conversion acts only on the active picture, ANC data can become corrupt outside of this region. In order to ensure that the embedded ANC data remains valid, we recommend extracting the ANC data with the receiver prior to the Level B/A conversion taking place. NOTE 1: If Level B/A conversion is enabled, previous 352M Payload ID packets are not deleted from the data stream. NOTE 2: When Level B/A conversion is enabled, timing reference information (FVH) present on the STAT outputs is not phase-aligned with the output video data, and should not be used for line or frame synchronization activities. Being that CEA 861 timing is derived from (FVH) timing reference information, it should not be used. During Level B to Level A conversion, it is advised that the user generates the H and V timing signals from the embedded TRS words. NOTE 3: If the GS2970 sees a synchronous switch where the difference in phases between two Level B inputs is greater than ~10.7s, the user may observe a missing H pulse on the line following the switch line, when Level B/A conversion is enabled. NOTE 4: Discontinuities in the line of video at the input of the Level B to A converter can cause erroneous mapping to the Level A format. Therefore, when enabling B to A GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 76 of 145 conversion or enabling/disabling audio, it is recommended to reset the Level B to A converter with the following sequence: 1. Assert the B to A converter reset by writing `1' to bit 3 of register 05Eh. 2. Monitor H-pulse for a high-to-low transition. 3. De-assert the B to A converter reset by writing `0' to bit 3 of register 05Eh. This must be completed at the beginning of AV and should be completed in 1920 PCLK periods. 4.19 Audio De-embedder The GS2970 includes an integrated audio de-embedder which is enabled by default in SMPTE mode. It can be disabled by setting the AUDIO_EN/DIS pin LOW, or by setting the host interface AUD_EXT_MASK bit to HIGH, or by keeping IOPROC_EN/DIS pin LOW. In non-SMPTE modes, the audio de-embedder is not active. Up to eight channels of audio may be extracted from the received serial digital video stream. The output signal formats supported by the device include AES/EBU, I2S (default) and industry standard serial digital formats. 16, 20 and 24-bit audio bit depths are supported for 48kHz synchronous audio for SD data rates. For HD and 3G data rates, 16, 20 and 24-bit audio bit depths are supported for 48kHz audio. The audio may be synchronous or asynchronous to the video. In 3G mode: * In Level A mode, all Audio Control Packets are extracted from Data Stream One and all Audio Data Packets are extracted from Data Stream Two, in accordance with SMPTE 425M. This is similar to HD, in which Audio Control Packets are embedded in the Luma channel and audio data packets in the Chroma channel * In Level B mode, extraction of audio packets from Link A (default) or Link B is selectable via the AUDIO_SEL_DS2_DS1 bit in the host interface Additional audio processing features include audio mute on loss of lock, de-embed and delete, group selection, audio output re-mapping, ECC error detection and correction (HD/3G modes only), and audio channel status extraction. 4.19.1 Serial Audio Data I/O Signals The Serial Audio Data I/O pins are listed in Table 4-16: Serial Audio Pin Descriptions. Table 4-16: Serial Audio Pin Descriptions Audio Pin Name AUDIO_EN/DIS Description Enable Input for Audio Processing AOUT_1/2 Serial Audio output; Channels 1 and 2 AOUT_3/4 Serial Audio output; Channels 3 and 4 AOUT_5/6 Serial Audio Output; Channels 5 and 6 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 77 of 145 Table 4-16: Serial Audio Pin Descriptions (Continued) Audio Pin Name Description AOUT_7/8 Serial Audio Output; Channels 7 and 8 ACLK 64fs clock WCLK Word clock AMCLK Audio Master Clock, selectable 128fs, 256fs, or 512fs The timing of the serial audio output signals, the WCLK output signal, and the ACLK output signal is as shown in Figure 4-33: ACLK to Data Signal Output Timing. I/O Timing Specs: Audio Outputs: 128fs = 162.76ns (AES/EBU) 64fs = 325.52ns (other modes) AOUT* A0 A1 80% A2 A3 80% ACLK 20% toh tr 20% tf tod Audio Outputs 3.3V AOUT toh 1.500ns tr/tf (min) 0.600ns Cload 6 pF tod tr/tf (max) 7.000ns 2.200ns 1.8V Cload 15 pF toh 1.500ns tr/tf (min) 0.600ns Cload 6 pF tod 7.000ns tr/tf (max) 2.300ns Cload 15 pF Figure 4-33: ACLK to Data Signal Output Timing When AUDIO_EN/DIS is set HIGH, audio extraction is enabled and the audio output signals are extracted from the video data stream. When set LOW, the serial audio outputs, ACLK and WCLK outputs are set LOW. In addition, all functional logic associated with audio extraction is disabled to reduce power consumption. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 78 of 145 4.19.2 Serial Audio Data Format Support The GS2970 supports the following serial audio data formats: * I2S (default) * AES/EBU * Serial Audio Left Justified, MSB First * Serial Audio Left Justified, LSB First * Serial Audio Right Justified, MSB First * Serial Audio Right Justified, LSB First (this mode is not supported in SD) By default (at power up or after system reset) I2S is selected. The other data formats are selectable via the host interface using the AMA/AMB[1:0] bits. Table 4-17: Audio Output Formats AMA/AMB[1:0] Audio Output Format 00 AES/EBU audio output 01 Serial audio output: Left Justified; MSB first 10 Serial audio output: Right Justified; MSB first 11 I2S (Default) The serial audio output formats may use LSB first according to the settings of the control bits LSB_FIRSTA, LSB_FIRSTB, LSB_FIRSTC, and LSB_FIRSTD. When in I2S mode, these control bits must all be set LOW (default). When I2S format is desired, both groups must be set to I2S (i.e. AMA = AMB = 11). This is because they share the same WCLK. Channel A (Left) WCLK Channel B (Right) ACLK 23 AOUT[8/7:2/1] 22 6 5 4 3 2 1 MSB 23 0 LSB 22 6 5 4 3 2 0 1 MSB LSB Figure 4-34: I2S Audio Output Format WCLK Channel A (Left) Channel B (Right) ACLK AOUT[8/7:2/1] 0 1 2 Preamble 3 4 5 6 AUX 7 27 28 29 30 8 LSB MSB V U C 31 0 P 1 2 Preamble 3 4 5 6 AUX 7 8 LSB 27 28 29 30 31 MSB V U C P Figure 4-35: AES/EBU Audio Output Format GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 79 of 145 WCLK Channel A (Left) Channel B (Right) ACLK AOUT[8/7:2/1] 23 22 21 6 5 4 3 2 1 MSB 0 23 LSB MSB 22 21 6 5 4 3 2 1 0 LSB Figure 4-36: Serial Audio, Left Justified, MSB First WCLK Channel A (Left) Channel B (Right) ACLK AOUT[8/7:2/1] 0 1 2 17 18 19 20 21 22 LSB 23 0 1 2 17 18 19 20 21 22 LSB MSB 23 MSB Figure 4-37: Serial Audio, Left Justified, LSB First Channel A (Left) WCLK Channel B (Right) ACLK AOUT[8/7:2/1] 23 22 21 20 19 18 17 2 1 MSB 0 23 LSB MSB 22 21 20 19 18 17 2 1 0 LSB Figure 4-38: Serial Audio, Right Justified, MSB First Channel A (Left) WCLK Channel B (Right) ACLK AOUT[8/7:2/1] 0 1 2 3 4 5 6 LSB 21 22 23 0 MSB LSB 1 2 3 4 5 6 21 22 23 MSB Figure 4-39: Serial Audio, Right Justified, LSB First 4.19.2.1 AES/EBU Mode In AES/EBU output mode, the audio de-embedder uses a 128fs (6.144MHz audio bit clock) clock as shown in Figure 4-40. 6.144MHz AMCLK (128fs) AOUT_1/2, AOUT_3/4 AOUT_5/6, AOUT_7/8 Figure 4-40: AES/EBU Audio Output to Bit Clock Timing 4.19.2.2 Audio Data Packet Extraction Block The audio de-embedder looks for audio data packets on every line of the incoming video. The audio data must be embedded according to SMPTE 272M (SD) or SMPTE 299M (HD or 3G). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 80 of 145 In 3G Level A signals, the audio data packets must be embedded only in Data Stream Two. In 3G Level B signals, the audio data packets must be embedded in the Chroma streams of either Link A or Link B. The Audio Group Detect registers are set HIGH when audio data packets with a corresponding group DID are detected in the input video stream. The host interface reports the individual audio groups detected. Table 4-18: Audio Data Packet Detect Register Name Description Default ADPG4_DET Audio Group Four Data Packet Detection (1: Detected) 0 ADPG3_DET Audio Group Three Data Packet Detection (1: Detected) 0 ADPG2_DET Audio Group Two Data Packet Detection (1: Detected) 0 ADPG1_DET Audio Group One Data Packet Detection (1: Detected) 0 When an audio data packet with a DID set in IDA[1:0] and IDB[1:0] is detected, the audio sample information is extracted and written into the audio FIFO. The embedded audio group selected by IDA[1:0] is described henceforth in this document as Group A or Primary Group. The embedded audio group selected by IDB[1:0] is described henceforth in this document as Group B or Secondary Group. Due to the large size of the horizontal ancillary data space in 720p/24, 720p/25 and 720p/30 video standards, the maximum number of ancillary data words the audio de-embedder can process is limited to 1024 when configured for these standards. 4.19.2.3 Audio Control Packets The audio de-embedder automatically detects the presence of audio control packets in the video stream. When audio control packets for audio Group A are detected, the CTRA_DET bit of the host interface is set HIGH. When audio control packets for audio Group B are detected, the CTRB_DET bit of the host interface is set HIGH. The audio control packet data is accessible via the host interface. The audio control packets must be embedded according to SMPTE 272M (SD) or SMPTE 299M (HD and 3G). In 3G Level A signals, the audio control packets must be embedded only in Data Stream One. In 3G Level B signals the audio control packets must be embedded in the Luma streams of each link that carries audio. NOTE: In SD, the control packet host interface registers are updated with new control packet values, after the CTRA_DET/CTRB_DET flags are cleared. In HD, the update happens automatically. 4.19.2.4 Setting Packet DID Table 4-19 below, shows the 2-bit host interface setting for the audio group DID's. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 81 of 145 For 24-bit audio support in SD mode, extended audio packets for Group A must have the same group DID set in IDA[1:0] of the host interface. Extended audio packets for Group B must have the same group DID set in IDB[1:0] of the host interface. The audio de-embedder automatically detects the presence of extended audio packets. When detected, the audio output format is set to 24-bit audio sample word length. The audio de-embedder defaults to audio Groups One and Two, where Group A is extracted from packets with audio Group One DID, and Group B from packets with audio Group Two DID. Table 4-19: Audio Group DID Host Interface Settings Audio Group SD Data DID SD Extended DID HD Data DID SD Control DID HD Control DID Host Interface Register Setting (2-bit) 1 2FFh 1FEh 2E7h 1EFh 1E3h 00b 2 1FDh 2FCh 1E6h 2EEh 2E2h 01b 3 1FBh 2FAh 1E5h 2EDh 2E1h 10b 4 2F9h 1F8h 2E4h 1ECh 1E0h 11b Table 4-20: Audio Data and Control Packet DID Setting Register Name Description Default IDA[1-0] Group A Audio data and control packet DID setting 00b IDB[1-0] Group B Audio data and control packet DID setting 01b 4.19.2.5 Audio Packet Delete Block To delete all ancillary data with a group DID shown in Table 4-19, the ALL_DEL bit in the host interface must be set HIGH. 4.19.2.6 ECC Error Detection & Correction Block (HD Mode Only) The audio de-embedder performs BCH(31,25) forward error detection and correction, as described in SMPTE 299M. The error correction for all embedded audio data packets is activated when the host interface ECC_OFF bit is set LOW (default LOW). The audio de-embedder corrects any errors in both the audio output and the embedded packet. When a one-bit error is detected in a bit array of the ECC protected region of the audio data packet with audio group DID set in IDA[1:0], the ECCA_ERROR flag is set HIGH. When a one-bit error is detected in the ECC protected region of the audio data packet with audio group DID set in IDB[1:0], the ECCB_ERROR flag is set HIGH. Figure 4-41 shows examples of error correction and detection. Up to 8 bits in error can be corrected, providing each bit error is in a different bit array (shown below). When there are two or more bits in error in the same 24-bit array, the errors are detected, but not corrected. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 82 of 145 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 24-bit array ADF ADF ADF DID DBN DC CLK CLK CH1 CH1 CH1 CH1 CH2 CH2 CH2 CH2 CH3 CH3 CH3 CH3 CH4 CH4 CH4 CH4 DID DBN DC CLK CLK CH1 CH1 CH1 CH1 CH2 CH2 CH2 CH2 CH3 CH3 CH3 CH3 CH4 CH4 CH4 CH4 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Errors corrected ADF ADF ADF Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Errors detected but not corrected Figure 4-41: ECC 24-bit Array and Examples 4.19.3 Audio Processing 4.19.3.1 Audio Clock Generation For SD and HD/3G audio, a single set of audio frequencies is generated for all audio channels, using a Direct Digital Period Synthesizer (DDPS) to minimize jitter. * For Mapping structure one signals (1080p 50, 59.94 or 60), the pixel clock is 148.5(/M) MHz, and the phase data are based on this rate. An Audio Master Clock (AMCLK) is also generated. The frequency is selectable via the host interface as: fs x 128 fs x 256 fs x 512 In SD mode, audio clocks are derived from the PCLK. In HD/3G modes, the input control for the DDPS is derived from the two embedded audio clock phase words in the audio data packet corresponding to Group A. The audio clock phase information used is taken from the first embedded audio packet in the HANC space. With no embedded audio present, the device will not generate ACLK or WCLK. The IGNORE_PHASE bit should be asserted in this case to ensure the proper AMCLK frequency is generated. The audio de-embedder also includes a Flywheel block to overcome any inconsistencies in the embedded audio clock phase information. If the audio phase data is not present in the audio data packets, or is incorrect, the NO_PHASEA_DATA bit in the host interface is set and the clock will free-run based on the detected video format, the PCLK and the M value. IGNORE_PHASE should be set HIGH when NO_PHASEA_DATA is set. This does not occur automatically. When the IGNORE_PHASE bit in the host interface is set HIGH, it is recommended that the M value be programmed via the host interface. This can be done by setting the GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 83 of 145 FORCE_M bit HIGH, and programming the desired value into FORCE_MEQ1001. The correct value can be obtained by reading the M bit from the Video Core Registers. If the DDPS is locked to phase data and audio data packets are lost or corrupted, the Clock Generator will flywheel for up to four audio data packets. If no valid audio data packet with valid phase data is provided within this time, the Clock Generator will free-run based on the video format, the PCLK and the M value. If the IGNORE_PHASE bit in the host interface is HIGH, the clock will free-run based on the video format, the PCLK and the M value, independent of the NO_PHASEA_DATA bit. In the 720p/24 video format, the total line length is 4125 pixels, which requires a resolution of 13 bits for the audio clock phase words in the embedded audio data packets. SMPTE 299M only specifies a maximum of 12 bits resolution. Proposed changes to SMPTE 299M suggest using bit 5 of UDW1 (currently reserved and set to zero) in the audio data packet as the MSB (ck13) for the audio clock phase data, providing 13 bits resolution. Some audio encoders may hold the clock phase value at a maximum value when reached, until reset at the end of the line. This produces a small amount of audio phase jitter for the period of one sample. To overcome this issue, the audio de-embedder checks for all cases. On detection of the maximum value, a comparison is made between previous clock phases and the correct position interpolated. If the clock phase data value starts to decrease, the de-embedder checks to see if bit 5 (ck13) of UDW1 in the audio data packet is set. If ck13 is set, the correct value is used. If ck13 is not set, the correct position is interpolated. 4.19.3.2 Detect 5-Frame Sequence Block 5-frame sequence detection is required for 525-line based video formats only. The audio de-embedder checks the Audio Frame Number sequence in the audio control packets, when present. If the audio frame sequence is running (repeated 1 to 5 count), the audio de-embedder uses this information to determine the 5-frame sequence. If the audio control packet is not present, or the Audio Frame Number words are set to 200h, the audio de-embedder detects the 5-frame sequence by counting the number of samples per frame. Figure 4-42 shows the number of samples per frame over a 5-frame sequence. 8008 Samples Frame 5 Frame 1 Frame 2 Frame 3 Frame 4 Frame 5 Frame 1 1602 1602 1601 1602 1601 1602 1602 1602 Repeat Figure 4-42: Sample Distribution over 5 Video Frames (525-line Systems) When the audio inputs are asynchronously switched or disrupted, the audio de-embedder continues to write audio samples into the audio buffer, based on the current 5-frame sequence. The de-embedder then re-locks to the new 5-frame sequence, at which point a sample may be lost. NOTE: In SD, all four channel pairs must follow the same 5-frame sequence. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 84 of 145 4.19.3.3 Audio FIFO Block The function of the FIFO block is to change the audio data word rate from the ANC rate multiplexed with the video signal to the 48kHz audio output rate. The audio FIFO block contains the audio sample buffers; one per audio channel. Each buffer is 36 audio samples deep. At power up or reset, the read pointer is held at the zero position until 26 samples have been written into the FIFO (allows for 6 lines per frame with no audio samples; a maximum of 4 samples per line in SD Mode). See Figure 4-43. Read Pointer 25 Address 0 35 Audio Buffer Write Pointer Figure 4-43: Audio Buffer After Initial 26 Sample Write The position of the write pointer with respect to the read pointer is monitored continuously. If the write pointer is less than 6 samples ahead of the read pointer (point A in Figure 4-44), a sample is repeated from the read-side of the FIFO. If the write pointer is less than 6 samples behind the read pointer (point B in Figure 4-44), a sample is dropped. This avoids buffer underflow/overflow conditions. Read Pointer Address 0 5 29 35 Audio Buffer A B Write Pointer Write Pointer Figure 4-44: Audio Buffer Pointer Boundary Checking The repeat or drop sample operation is performed a maximum of 28 consecutive times, after which the audio outputs are muted (all sample data set to zero). In SD Mode, 26 samples are required to be written into the FIFO prior to starting the read operation again. The audio buffer pointer offset may be reduced from 26 samples to 12 or 6 samples using the OS_SEL[1:0] bits in the host interface. The default setting is 26 samples (see Table 4-21). GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 85 of 145 When the OS_SEL[1:0] bits are set for 6-sample pointer offset, no boundary-checking is performed. In HD mode the audio FIFO is a maximum of 10 samples deep. According to SMPTE 299M, audio samples are multiplexed immediately in the next HANC region after the audio sample occurs. Table 4-21: Audio Buffer Pointer Offset Settings OS_SEL[1:0] Buffer Pointer Offset 00 26 samples (default) 01 12 samples 10 6 samples 4.19.3.4 Audio Crosspoint Block The Audio Crosspoint is used for audio output channel re-mapping. This feature allows any of the selected audio channels in Group A or Group B to be output on any of the eight output channels. The default setting is for one to one mapping, where AOUT_1/2 is extracted from Group A CH1 and CH2, AOUT_3/4 is extracted from Group A CH3 and CH4, and so on. NOTE: If audio samples from embedded audio packets with the group set in IDA[1:0] are to be paired with samples from the group set in IDB[1:0], all of the channels must have been derived from the same Word Clock and must be synchronous. The output channel is set in the OPn_SRC[2:0] host interface registers. Table 4-22 lists the 3-bit address for audio channel mapping. Table 4-22: Audio Channel Mapping Codes Audio Output Channel 3-bit Host Interface Source Address 1 000 2 001 3 010 4 011 5 100 6 101 7 110 8 111 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 86 of 145 4.19.3.5 Serial Audio Output Word Length The audio output, in serial modes, has a selectable 24, 20 or 16-bit sample word length. The ASWL[1:0] host interface register is used to configure the audio output sample word length. Figure 4-23 shows the host interface 2-bit code for setting the audio sample word length. When the presence of extended audio packets is detected in SD modes, the audio de-embedder defaults to 24-bit audio sample word length. Table 4-23: Audio Sample Word Lengths ASWL[1:0] Audio Sample Word Length (SD) Audio Sample Word Length (HD) 00 24-bit 24-bit 01 20-bit 20-bit 10 16-bit 16-bit 11 Auto 24/20-bit (Default) Reserved (Default) NOTE: By default, at power-up, the word length is set to 12 bits. The desired word length should be programmed through the host interface. 4.19.3.6 Audio Channel Status The GS2970 detects the AES/EBU Audio Channel Status (ACS) block information for each of the selected channel pairs. ACS data detection is indicated by corresponding ACS_DET flag bits in the host interface. The flag is cleared by writing to the same location. 4.19.3.6.1 Audio Channel Status Read AES/EBU ACS data is available separately for each of the channels in a stereo pair. The GS2970 defaults to reading the first channel of each pair. There are 184 bits in each ACS packet, which are written to twelve 16-bit right-justified registers in the host interface. The ACS_USE_SECOND bit (default LOW) selects the second channel in each audio pair when set HIGH. Once all of the ACS data for a channel has been acquired, the corresponding ACS_DET bit is set, and acquisition stops. The ACS data is overwritten with new data when the ACS_DET bit is cleared in the system. 4.19.3.6.2 Audio Channel Status Regeneration When the ACS_REGEN bit in the host interface is set HIGH, the audio de-embedder embeds the 24 bytes of the Audio Channel Status information programmed in the ACSR[183:0] registers into the 'C' bit of the AES/EBU outputs. The same Audio Channel Status information is used for all output channels. In order to apply ACSR data; * Set the ACS_REGEN bit to logic HIGH * Write the desired ACSR data to the ACSR registers * Set the ACS_APPLY bit to HIGH GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 87 of 145 At the next status boundary, the device outputs the contents of the ACSR registers as ACS data. This event may occur at a different time for each of the output channels. While waiting for the status boundary, the device sets the appropriate ACS_APPLY_WAIT[A:D] flag. Table 4-24 shows the host interface default settings for the Audio Channel Status block. The audio de-embedder automatically generates the CRC word. Table 4-24: Audio Channel Status Information Registers Name Description Default ACSR[7-0] Audio channel status block byte 0 set. Used when ACS_REGEN is set HIGH 85h ACSR[15-8] Audio channel status block byte 1 set. Used when ACS_REGEN is set HIGH 08h ACSR[23-16] Audio channel status block byte 2 set. Used when ACS_REGEN is set HIGH 28h (SD) 2Ch (HD) ACSR[31-24]: Audio channel status block data for bytes 3 to 22. Used when ACS_REGEN is set HIGH 00h ACS_REGEN Audio channel status regenerate 0 ACS_APPLY Apply new ACSR data 0 ACS_APPLY_W Waiting to apply new ACSR data 0 Audio channel status block data for bytes 0 to 22 00h: 00h ACSR[183-176] AIT[A:D] ACS[7-0]: ACS[183-176] Table 4-25: Audio Channel Status Block for Regenerate Mode Default Settings Name Byte Bit Default Mode PRO 0 0 1b Professional use of channel status block Emphasis 0 2-4 100b 100b None. Rec. manual override disabled Sample Frequency 0 6-7 01b 48kHz. Manual override or auto disabled Channel Mode 1 0-3 0001b Two channels. Manual override disabled AUX 2 0-2 000b SD Modes: Maximum audio word length is 20 bits 001b HD Mode: Maximum audio word length is 24 bits 101b Maximum word length (based on AUX setting). Source Word Length 2 3-5 24-bit for HD Mode; 20-bit for SD Modes All other bits set to zero GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 88 of 145 4.19.3.7 Audio Mute When the MUTE bits in the host interface are set HIGH, the audio outputs are muted (all audio sample bits are set to zero). To set all the audio output channels to mute, set the host interface MUTE_ALL bit HIGH. Table 4-26: Audio Mute Control Bits Name Description Default MUTE_ALL Ch1-8 audio mute enable (1: Enabled) 0 MUTE8 Ch8 audio mute enable (1: Enabled) 0 MUTE7 Ch7 audio mute enable (1: Enabled) 0 MUTE6 Ch6 audio mute enable (1: Enabled) 0 MUTE5 Ch5 audio mute enable (1: Enabled) 0 MUTE4 Ch4 audio mute enable (1: Enabled) 0 MUTE3 Ch3 audio mute enable (1: Enabled) 0 MUTE2 Ch2 audio mute enable (1: Enabled) 0 MUTE1 Ch1 audio mute enable (1: Enabled) 0 4.19.3.7.1 Mute On Loss Of Lock When the GS2970 loses lock (LOCKED signal is LOW), the audio de-embedder sets all audio outputs LOW (no audio formatting is performed). The ACLK, WCLK and AMCLK outputs are also forced LOW. 4.19.4 Error Reporting 4.19.4.1 Data Block Number Error When the 1-255 count sequence in the Data Block Number (DBN) word of Group A audio data packets is discontinuous, the DBNA_ERR bit in the host interface AUDIO_ERROR_STAT_X register is set HIGH. When the 1-255 count sequence in the DBN word of Group B audio data packets is discontinuous, the DBNB_ERR bit in the AUDIO_ERROR_STAT_X register is set HIGH. The DBNA_ERR and DBNB_ERR flags also have associated SD_AUDIO_ERROR_MASK and HD_AUDIO_ERROR_MASK register flags for configuration of error reporting in the Receiver. The DBNA_ERR and DBNB_ERR flags remains set until cleared by writing to these locations. 4.19.4.2 ECC Error The GS2970 monitors the ECC error status of the two selected audio groups, as described in Section 4.19.2.6 on page 82. The ECC[N]_ERROR flags also have associated SD_AUDIO_ERROR_MASK and HD_AUDIO_ERROR_MASK register flags for configuration of error reporting in the Receiver. The ECC[N]_ERROR flags remain set until read via the host interface. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 89 of 145 4.20 GSPI - HOST Interface The GSPI, or Gennum Serial Peripheral Interface, is a 4-wire interface provided to allow the system to access additional status and control information through configuration registers in the GS2970. The GSPI is comprised of a Serial Data Input signal (SDIN), Serial Data Output signal (SDOUT), an active low Chip Select (CS), and a Burst Clock (SCLK). Because these pins are shared with the JTAG interface port, an additional control signal pin JTAG/HOST is provided. When JTAG/HOST is LOW, the GSPI interface is enabled. When JTAG/HOST is HIGH, the JTAG interface is enabled. When operating in GSPI mode, the SCLK, SDIN, and CS signals must be provided by the system. The SDOUT pin is a non-clocked loop-through of SDIN and may be connected to the SDIN of another device, allowing multiple devices to be connected to the GSPI chain. See Section 4.20.2 for details. The interface is illustrated in the Figure 4-45 below. Application Host GS2970 SCLK SCLK CS1 CS SDOUT SDIN SDOUT GS2970 SCLK CS2 CS SDIN SDOUT SDIN Figure 4-45: GSPI Application Interface Connection All read or write access to the GS2970 is initiated and terminated by the system host processor. Each access always begins with a Command/Address Word, followed by a data write to, or data read from, the GS2970. 4.20.1 Command Word Description The Command Word consists of a 16-bit word transmitted MSB first and contains a read/write bit, an Auto-Increment bit and a 12-bit address. MSB R/W LSB RSV RSV AutoInc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Figure 4-46: Command Word Format GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 90 of 145 Command Words are clocked into the GS2970 on the rising edge of the Serial Clock SCLK, which operates in a burst fashion. The chip select (CS) signal must be set low a minimum of 1.5ns (t0 in Figure 4-48) before the first clock edge to ensure proper operation. When the Auto-Increment bit is set LOW, each Command Word must be followed by only one Data Word to ensure proper operation. If the Auto-Increment bit is set HIGH, the following Data Word is written into the address specified in the Command Word, and subsequent Data Words are written into incremental addresses from the first Data Word. This facilitates multiple address writes without sending a Command Word for each Data Word. NOTE: The RSV bits in the GSPI command word can be set to zero as placeholder, though these bits are not used. 4.20.2 Data Read or Write Access During a read sequence (Command Word R/W bit set HIGH) serial data is transmitted or received MSB first, synchronous with the rising edge of the serial clock SCLK. The Chip Select (CS) signal must be set low a minimum of 1.5ns (t0 in Figure 4-48) before the first clock edge to ensure proper operation. The first bit (MSB) of the Serial Output (SDOUT) is available (t5 in Figure 4-49) following the last falling SCLK edge of the read Command Word, the remaining bits are clocked out on the negative edges of SCLK. NOTE: When several devices are connected to the GSPI chain, only one CS may be asserted during a read sequence. During a write sequence (Command Word R/W bit set LOW), a wait state of 37.1ns (t4 in Figure 4-48) is required between the Command Word and the following Data Word. This wait state must also be maintained between successive Command Word/Data Word write sequences. When Auto Increment mode is selected (AutoInc = 1), the wait state must be maintained between successive Data Words after the initial Command Word/Data Word sequence. During the write sequence, all Command and following Data Words input at the SDIN pin are output at the SDOUT pin unchanged. When several devices are connected to the GSPI chain, data can be written simultaneously to all the devices which have CS set LOW. MSB D15 LSB D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-47: Data Word Format GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 91 of 145 4.20.3 GSPI Timing Write and Read Mode timing for the GSPI interface; t0 t1 t7 t4 SCLK _TCLK t3 t8 t2 CS _TMS SDIN _TDI SDOUT _TDO R/W R/W RSV RSV RSV Auto _Inc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RSV Auto _ Inc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-48: Write Mode t5 SCLK _TCLK t6 CS _ TMS SDIN _TDI SDOUT _TDO R /W RSV RSV Auto _Inc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 R/W RSV RSV Auto _Inc A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Figure 4-49: Read Mode SDIN_TDI to SDOUT_TDO combinational path for daisy chain connection of multiple GS2970. TDELAY SDIN_TDI data_0 SDOUT_TDO data_0 Figure 4-50: GSPI Time Delay Table 4-27: GSPI Time Delay Parameter Symbol Conditions Min Typ Max Units Delay Time tDELAY 50% levels; 1.8V operation - - 13.1 ns Delay Time tDELAY 50% levels; 3.3V operation - - 9.7 ns GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 92 of 145 Table 4-28: GSPI Timing Parameters (50% levels; 3.3V or 1.8V operation) Parameter Symbol Min Typ Max Units CS low before SCLK rising edge t0 1.5 - - ns SCLK period t1 16.67 - - ns SCLK duty cycle t2 40 50 60 % Input data setup time t3 1.5 - - ns Time between end of Command Word (or data in Auto-Increment mode) and the first SCLK of the following Data Word - write cycle t4 - - ns - - ns Time between end of Command Word (or data in Auto-Increment mode) and the first SCLK of the following Data Word - read cycle. t5 PCLK (MHz) ns unlocked 100 27.0 37.1 74.25 13.5 148.5 6.7 PCLK (MHz) ns unlocked - 27.0 148.4 74.25 53.9 148.5 27 Time between end of Command Word (or data in Auto-Increment mode) and the first SCLK of the following Data Word - read cycle - ANC FIFO Read t5 222.6 - - ns Output hold time (15pF load) t6 1.5 - - ns CS high after last SCLK rising edge t7 - - ns - - ns Input data hold time t8 PCLK (MHz) ns unlocked 445 27.0 37.1 74.25 13.5 148.5 6.7 1.5 This timing must be satisfied across all ambient temperature and power supply operating conditions, as described in the Electrical Characteristics on page 16. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 93 of 145 4.21 Host Interface Register Maps NOTE: The GS2970 only accepts write/read commands to/from the Audio Register Maps when the audio core is locked to the incoming video data rate. The Video Register Map is always active, whether valid serial input data is present or not. 4.21.1 Video Core Registers Table 4-29: Video Core Configuration and Status Registers Address Register Name 000h IOPROC_1 Bit Name Bit Description R/W Default RSVD 15 Reserved. R 0 TRS_WORD_REMAP_DS1 _DISABLE 14 Disables 8-bit TRS word remapping for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. R/W 0 RSVD 13 Reserved. R/W 0 EDH_FLAG_UPDATE _MASK 12 Disables updating of EDH error flags. R/W 0 EDH_CRC_INS_MASK 11 Disables EDH_CRC error correction and insertion. R/W 0 H_CONFIG 10 Selects the H blanking indication: R/W 0 0: Active line blanking - the H output is HIGH for all the horizontal blanking period, including the EAV and SAV TRS words. 1: TRS based blanking - the H output is set HIGH for the entire horizontal blanking period as indicated by the H bit in the received TRS signals. This signal is only valid when TIM_861 is set to '0' (via pin or host interface). ANC_DATA_EXT_MASK 9 Disables ancillary data extraction FIFO. R/W 0 AUD_EXT_MASK 8 Disables audio extraction block. R/W 0 TIM_861_PIN_DISABLE 7 Disable TIM_861 pin control when set to '1', and use TIMING_861 bit instead. R/W 0 TIMING_861 6 Selects the output timing reference format: 0 = Digital FVH timing output; 1 = CEA-861 timing output. R/W 0 RSVD 5 Reserved. R/W 0 ILLEGAL_WORD_REMAP _DS1_MASK 4 Disables illegal word remapping for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 94 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 000h IOPROC_1 001h IOPROC_2 Bit Name Bit Description R/W Default ANC_CHECKSUM _INSERTION_DS1_MASK 3 Disables insertion of ancillary data checksums for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. R/W 0 CRC_INS_DS1_MASK 2 Disables insertion of HD/3G CRC words for 3G Level B Data Stream 1, 3G Level A, and HD inputs. R/W 0 LNUM_INS_DS1_MASK 1 Disables insertion of line numbers for 3G Level B Data Stream 1, 3G Level A, and HD inputs. R/W 0 TRS_INS_DS1_MASK 0 Disables insertion of TRS words for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. R/W 0 Reserved. R/W N/A RSVD 15-13 TRS_WORD_REMAP_DS2 _DISABLE 12 Disables 8-bit TRS word remapping in Data Stream 2 (3G Level B only). R/W 0 RSVD 11 Reserved. R/W 0 REGEN_352M_MASK 10 Disables regeneration of the SMPTE 352M packet for 3G Level B data. Note: this bit needs to be enabled via the host interface to disable SMPTE 352M packet generation. It is strongly recommended to set this bit LOW only when Level B to Level A conversion is enabled. R/W 0 DS_SWAP_3G 9 Swaps Data Stream 1 (DS1) and Data Stream 2 (DS2) at the output in 3G mode. R/W 0 R/W 1 In 20-bit output mode, DS1 shall be present on DOUT pins [19:10] and DS2 shall be present on DOUT pins [9:0] by default. When DS_SWAP_3G is set to '1', DS2 shall be present on DOUT pins [19:10] and DS1 shall be present on DOUT pins [9:0] In 10-bit (DDR) output mode, DS2 shall precede DS1 by default. When DS_SWAP_3G is set to '1', DS1 shall precede DS2. LEVEL_B2A_CONV _DISABLE_MASK GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 8 Disable conversion of a 3G Level B input to a 3G Level A format. Only effective if in 3G Level B mode. Default is active HIGH (disabled), so Level B inputs are formatted as Level B outputs. 95 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 001h IOPROC_2 002h ERROR_STAT_1 Bit Name Bit Description R/W Default ANC_EXT_SEL_DS2_DS1 7 Selects data stream to extract ANC data from (valid for 3G Level B data). R/W 0 AUDIO_SEL_DS2_DS1 6 Selects data stream to be sent to audio core (valid for 3G Level B data). R/W 0 RSVD 5 Reserved. R/W 0 ILLEGAL_WORD_REMAP _DS2_MASK 4 Disables illegal word remapping in Data Stream 2 (3G Level B only). R/W 0 ANC_CHECKSUM _INSERTION_DS2_MASK 3 Disables insertion of ancillary data checksums in Data Stream 2 (3G Level B only). R/W 0 CRC_INS_DS2_MASK 2 Disables insertion of CRC words in Data Stream 2 (3G Level B only). R/W 0 LNUM_INS_DS2_MASK 1 Disables insertion of line numbers in Data Stream 2 (3G Level B only). R/W 0 TRS_INS_DS2_MASK 0 Disable insertion of TRS words in Data Stream 2 (3G Level B only). R/W 0 Reserved. ROCW 0 RSVD 15-11 VD_STD_ERR_DS1 10 Video Standard Error indication for HD and SD inputs. ROCW 0 FF_CRC_ERR 9 EDH Full Frame CRC error indication. ROCW 0 AP_CRC_ERR 8 EDH Active Picture CRC error indication. ROCW 0 RSVD 7 Reserved. ROCW 0 CCS_ERR_DS1 6 Chroma ancillary data checksum error indication for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. ROCW 0 YCS_ERR_DS1 5 Luma ancillary data checksum error indication for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. ROCW 0 CCRC_ERR_DS1 4 Chroma CRC error indication for 3G Level B Data Stream 1, 3G Level A, and HD inputs. ROCW 0 YCRC_ERR_DS1 3 Luma CRC error indication for 3G Level B Data Stream 1, 3G Level A, and HD inputs. ROCW 0 LNUM_ERR_DS1 2 Line number error indication for 3G Level B Data Stream 1, 3G Level A, and HD inputs. ROCW 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 96 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 002h ERROR_STAT_1 003h 004h ERROR_STAT_2 EDH_FLAG_IN Bit Name Bit Description R/W Default SAV_ERR_DS1 1 SAV error indication for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. ROCW 0 EAV_ERR_DS1 0 EAV error indication for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. ROCW 0 Reserved. ROCW 0 RSVD 15-7 CCS_ERR_DS2 6 Chroma ancillary data checksum error indication for Data Stream 2 (3G Level B only). ROCW 0 YCS_ERR_DS2 5 Luma ancillary data checksum error indication for Data Stream 2 (3G Level B only). ROCW 0 CCRC_ERR_DS2 4 Chroma CRC error indication for Data Stream 2 (3G Level B only). ROCW 0 YCRC_ERR_DS2 3 Luma CRC error indication for Data Stream 2 (3G Level B only). ROCW 0 LNUM_ERR_DS2 2 Line number error indication for Data Stream 2 (3G Level B only). ROCW 0 SAV_ERR_DS2 1 SAV error indication for Data Stream 2 (3G Level B only). ROCW 0 EAV_ERR_DS2 0 EAV error indication for Data Stream 2 (3G Level B only). ROCW 0 EDH_DETECT 15 Embedded EDH packet detected. R 0 ANC_UES_IN 14 Ancillary data - unknown error status flag. R 0 ANC_IDA_IN 13 Ancillary data - internal error detected already flag. R 0 ANC_IDH_IN 12 Ancillary data - internal error detected here flag R 0 ANC_EDA_IN 11 Ancillary data - error detected already flag. R 0 ANC_EDH_IN 10 Ancillary data - error detected here flag. R 0 FF_UES_IN 9 EDH Full Field - unknown error status flag. R 0 FF_IDA_IN 8 EDH Full Field - internal error detected already flag. R 0 FF_IDH_IN 7 EDH Full Field - internal error detected here flag. R 0 FF_EDA_IN 6 EDH Full Field - error detected already flag. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 97 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit 004h EDH_FLAG_IN FF_EDH_IN 5 AP_UES_IN 005h 005h EDH_FLAG_OUT EDH_FLAG_OUT R/W Default EDH Full Field - error detected here flag. R 0 4 EDH Active Picture - unknown error status flag. R 0 AP_IDA_IN 3 EDH Active Picture - internal error detected already flag. R 0 AP_IDH_IN 2 EDH Active Picture - internal error detected here flag. R 0 AP_EDA_IN 1 EDH Active Picture - error detected already flag. R 0 AP_EDH_IN 0 EDH Active Picture - error detected here flag. R 0 RSVD 15 Reserved. R 0 ANC_UES 14 Ancillary data - Unknown Error Status flag. R 1 ANC_IDA 13 Ancillary data - Internal error Detected Already flag. R 0 ANC_IDH 12 Ancillary data - Internal error Detected Here flag. R 0 ANC_EDA 11 Ancillary data - Error Detected Already flag. R 0 ANC_EDH 10 Ancillary data - Error Detected Here flag. R 0 FF_UES 9 EDH Full Field - Unknown Error Status flag. R 1 FF_IDA 8 EDH Full Field - Internal error Detected Already flag. R 0 FF_IDH 7 EDH Full Field - Internal error Detected Here flag. R 0 FF_EDA 6 EDH Full Field - Error Detected Already flag. R 0 FF_EDH 5 EDH Full Field - Error Detected Here flag. R 0 AP_UES 4 EDH Active Picture - Unknown Error Status flag. R 1 AP_IDA 3 EDH Active Picture - Internal error Detected Already flag. R 0 AP_IDH 2 EDH Active Picture - Internal error Detected Here flag. R 0 AP_EDA 1 EDH Active Picture - Error Detected Already flag. R 0 AP_EDH 0 EDH Active Picture - Error Detected Here flag. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Description 98 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 006h DATA_FORMAT_ DS1 FF_CRC_V 15 EDH Full Field CRC Validity bit. R 0 AP_CRC_V 14 EDH Active Picture CRC Validity bit. R 0 VD_STD_DS1 13-8 Detected Video Standard for 3G Level B Data Stream 1, 3G Level A, HD and SD inputs. R 29 CDATA_FORMAT_DS1 7-4 Data format as indicated in Chroma channel for 3G Level B Data Stream 1, HD and SD inputs; R 15 R 15 Data format as indicated in Data Stream 2 for 3G Level A inputs. YDATA_FORMAT_DS1 3-0 Data format as indicated in Luma channel for 3G Level B Data Stream 1, HD and SD inputs; Data format as indicated in Data Stream 1 for 3G Level A inputs. 007h DATA_FORMAT_ DS2 RSVD 15-14 Reserved. R 0 VD_STD_DS2 13-8 Detected Video Standard for Data Stream 2 (3G Level B only). R 29 CDATA_FORMAT_DS2 7-4 Data Format as indicated in Chroma channel for Data Stream 2 (3G Level B only). R 15 YDATA_FORMAT_DS2 3-0 Data Format as indicated in Luma channel for Data Stream 2 (3G Level B only). R 15 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 99 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 008h IO_CONFIG Bit Name Bit Description RSVD 15 STAT2_CONFIG 14-10 R/W Default Reserved. RW 0 Configure STAT2 output pin: RW 2 00000: H Blanking when TIM_861 = 0; HSYNC when TIM_861 = 1 00001: V Blanking when TIM_861 = 0; VSYNC when TIM_861 = 1 00010: F bit when TIM_861 = 0; Data Enable (DE) when TIM_861 = 1 00011: LOCKED 00100: Y/1ANC: ANC indication (SD), Luma ANC indication (HD), Data Stream 1 ANC data indication (3G) 00101: C/2ANC: Chroma ANC indication (HD) or Data Stream 2 ANC data indication (3G) 00110: Data Error 00111: Video Error 01000: Audio Error 01001: EDH Detected 01010: Carrier Detect 01011: RATE_DET0 01100: RATE_DET1 01101 - 11111: Reserved 009h IO_CONFIG2 STAT1_CONFIG 9-5 Configure STAT1 output pin. (Refer to above for decoding) RW 1 STAT0_CONFIG 4-0 Configure STAT0 output pin. (Refer to above for decoding) RW 0 RSVD 15 Reserved. RW 0 STAT5_CONFIG 14-10 Configure STAT5 output pin. (Refer to above for decoding) RW 6 STAT4_CONFIG 9-5 Configure STAT4 output pin. (Refer to above for decoding) RW 4 STAT3_CONFIG 4-0 Configure STAT3 output pin. (Refer to above for decoding) RW 3 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 100 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 00Ah ANC_CONTROL Bit Name Bit Description R/W Default RSVD 15-4 Reserved. RW 0 ANC_DATA_SWITCH 3 Switches between FIFO memories. RW 0 ANC_DATA_DEL 2 Remove Ancillary Data from output video stream, set to Luma and Chroma blanking values. RW 0 HD_ANC_Y1_C2 1 Extract Ancillary data from Luma and Chroma channels (HD inputs) RW 0 RW 0 Extract Ancillary data from Data Stream 1 and Data Stream 2 (3G Level A inputs) Extract Ancillary data from Luma and Chroma channels of Data Stream 1 (3G Level B inputs, when ANC_EXT_SEL_DS2_DS1 = 0) Extract Ancillary data from Luma and Chroma channels of Data Stream 2 (3G Level B inputs, when ANC_EXT_SEL_DS2_DS1 = 1) HD_ANC_C2 0 Extract Ancillary data only from Chroma channel (HD inputs) Extract Ancillary data only from Data Stream 2 (3G Level A inputs) Extract Ancillary data only from Chroma channel of Data Stream 1 (3G Level B inputs, when ANC_EXT_SEL_DS2_DS1 = 0) Extract Ancillary data only from Chroma channel of Data Stream 2 (3G Level B inputs, when ANC_EXT_SEL_DS2_DS1 = 1) 00Bh 00Ch ANC_LINE_A ANC_LINE_B RSVD 15-11 Reserved. R/W 0 ANC_LINE_A 10-0 Video Line to extract Ancillary data from. R/W 0 RSVD 15-11 Reserved. R/W 0 ANC_LINE_B 10-0 Second video Line to extract Ancillary data from. R/W 0 RSVD 15-0 Reserved. R 0 00Dh 00Eh RSVD 00Fh ANC_TYPE_1_AP 1 ANC_TYPE1_DS1 15-0 Programmable DID/SDID pair #1 to extract from 3G Level B Data Stream 1, 3G Level A, HD and SD input formats ([15:8] = DID, [7:0] =SDID). R/W 0 010h ANC_TYPE_2_AP 1 ANC_TYPE2_DS1 15-0 Programmable DID/SDID pair #2 to extract from 3G Level B Data Stream 1, 3G Level A, HD and SD input formats ([15:8] = DID, [7:0] =SDID). R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 101 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 011h ANC_TYPE_3 _AP1 ANC_TYPE3_DS1 15-0 Programmable DID/SDID pair #3 to extract from 3G Level B Data Stream 1, 3G Level A, HD and SD input formats ([15:8] = DID, [7:0] =SDID). R/W 0 012h ANC_TYPE_4 _AP1 ANC_TYPE4_DS1 15-0 Programmable DID/SDID pair #4 to extract from 3G Level B Data Stream 1, 3G Level A, HD and SD input formats ([15:8] = DID, [7:0] =SDID). R/W 0 013h ANC_TYPE_5 ANC_TYPE5_DS1 15-0 Programmable DID/SDID pair #5 to extract from 3G Level B Data Stream 1, 3G Level A, HD and SD input formats ([15:8] = DID, [7:0] =SDID). R/W 0 _AP1 014h ANC_TYPE_1 _AP2 ANC_TYPE1_DS2 15-0 Programmable DID/SDID pair #1 to extract from 3G Level B Data Stream 2 ([15:8] = DID, [7:0] =SDID). R/W 0 015h ANC_TYPE_2 _AP2 ANC_TYPE2_DS2 15-0 Programmable DID/SDID pair #2 to extract from 3G Level B Data Stream 2 ([15:8] = DID, [7:0] =SDID). R/W 0 016h ANC_TYPE_3 _AP2 ANC_TYPE3_DS2 15-0 Programmable DID/SDID pair #3 to extract from 3G Level B Data Stream 2 ([15:8] = DID, [7:0] =SDID). R/W 0 017h ANC_TYPE_4 _AP2 ANC_TYPE4_DS2 15-0 Programmable DID/SDID pair #4 to extract from 3G Level B Data Stream 2 ([15:8] = DID, [7:0] =SDID). R/W 0 018h ANC_TYPE_5 _AP2 ANC_TYPE5_DS2 15-0 Programmable DID/SDID pair #5 to extract from 3G Level B Data Stream 2 ([15:8] = DID, [7:0] =SDID). R/W 0 019h VIDEO_FORMAT _352_A_1 VIDEO_FORMAT_2_DS1 15-8 SMPTE 352M embedded packet - byte 2. R 0 VIDEO_FORMAT_1_DS1 7-0 SMPTE 352M embedded packet - byte 1: [7]: Version identifier [6:0]: Video Payload Identifier. R 0 VIDEO_FORMAT_4_DS1 15-8 SMPTE 352M embedded packet - byte 4. R 0 VIDEO_FORMAT_3_DS1 7-0 SMPTE 352M embedded packet - byte 3. R 0 VIDEO_FORMAT_2_DS2 15-8 SMPTE 352M embedded packet - byte 2 (3G Data Stream 2 only). R 0 VIDEO_FORMAT_1_DS2 7-0 SMPTE 352M embedded packet - byte 1 (3G Data Stream 2 only): R 0 01Ah 01Bh VIDEO_FORMAT _352_B_1 VIDEO_FORMAT _352_A_2 [7]: Version identifier [6:0]: Video Payload Identifier. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 102 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description 01Ch VIDEO_FORMAT _352_B_2 VIDEO_FORMAT_4_DS2 15-8 VIDEO_FORMAT_3_DS2 01Dh 01Eh 01Fh 020h 021h 022h VIDEO_FORMAT _352_INS_A VIDEO_FORMAT _352_INS_B RASTER_STRUC_ 1 RASTER_STRUC_ 2 RASTER_STRUC_ 3 RASTER_STRUC_ 4 R/W Default SMPTE 352M embedded packet - byte 4 (3G Data Stream 2 only). R 0 7-0 SMPTE 352M embedded packet - byte 3 (3G Data Stream 2 only). R 0 VIDEO_FORMAT_2_INS 15-8 SMPTE 352M packet - byte 2 to be embedded after Level B to Level A conversion. R/W 0 VIDEO_FORMAT_1_INS 7-0 SMPTE 352M packet - byte 1 to be embedded after Level B to Level A conversion. R/W 0 VIDEO_FORMAT_4_INS 15-8 SMPTE 352M packet - byte 4 to be embedded after Level B to Level A conversion. R/W 0 VIDEO_FORMAT_3_INS 7-0 SMPTE 352M packet - byte 3 to be embedded after Level B to Level A conversion. R/W 0 RSVD 15-14 Reserved. R 0 WORDS_PER_ACTLINE 13-0 Words Per Active Line. R 0 RSVD 15-14 Reserved. R 0 WORDS_PER_LINE 13-0 Total Words Per Line. R 0 RSVD 15-11 Reserved. R 0 LINES_PER_FRAME 10-0 Total Lines Per Frame. R 0 RATE_SEL_READBACK 15-14 Read back detected data rate: R 0 R 0 0 = HD, 1,3=SD, 2=3G M 13 Specifies detected M value 0: 1.000 1: 1.001 Note: In certain systems, due to greater ppm offsets in the crystal, the `m' bit may not assert properly. In such cases, bits 3:0 in Register 06Fh can be increased to a maximum value of STD_LOCK 12 Video standard lock. R 0 INT_PROG 11 Interlaced or progressive. R 0 Active lines per frame. R 0 ACTLINE_PER_FIELD GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 10-0 103 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 023h FLYWHEEL _STATUS 024h RATE_SEL Bit Name Bit Description R/W Default RSVD 15-5 Reserved. R 0 V_LOCK_DS2 4 Indicates that the timing signal generator is locked to vertical timing (3G Level B Data Stream 2 only). R 0 H_LOCK_DS2 3 Indicates that the timing signal generator is locked to horizontal timing (3G Level B Data Stream 2 only). R 0 RSVD 2 Reserved. R 0 V_LOCK_DS1 1 Indicates that the timing signal generator is locked to vertical timing (3G Level B Data Stream 1, 3G Level A, HD and SD inputs). R 0 H_LOCK_DS1 0 Indicates that the timing signal generator is locked to horizontal timing (3G Level B Data Stream 1, 3G Level A, HD and SD inputs). R 0 Reserved. R 0 Detect data rate automatically (1) or program manually (0). R/W 1 Programmable rate select in manual mode: R/W 0 Reserved. R 0 Indicates standard is not recognized for CEA 861 conversion. R 1 RSVD AUTO/MAN RATE_SEL_TOP 15-3 2 1-0 0 = HD, 1,3=SD, 2=3G 025h 026h 027h 036h TIM_861_ FORMAT TIM_861_CFG RSVD RSVD FORMAT_ERR 15-7 6 FORMAT_ID_861 5-0 CEA-861 format ID of input video stream. Refer to Table 4-9. R 0 RSVD 15-3 Reserved. R 0 VSYNC_INVERT 2 Invert output VSYNC pulse. R/W 0 HSYNC_INVERT 1 Invert output HSYNC pulse. R/W 0 TRS_861 0 Sets the timing reference outputs to DFP timing mode when set to '1'. By default, the timing reference outputs follow CEA-861 timing mode. Only valid when TIM_861 is set to '1'. R/W 0 RSVD - Reserved. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 104 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description 037h ERROR_MASK_1 RSVD 15-11 Reserved. ERROR_MASK_1 10-0 Error mask for global error vector (3G Level B Data Stream 1, 3G Level A, HD, SD): R/W Default R 0 R/W 0 R 0 R/W 0 R 0 bit[0]: EAV_ERR_DS1 mask bit[1]: SAV_ERR_DS1 mask bit[2]: LNUM_ERR_DS1 mask bit[3]: YCRC_ERR_DS1 mask bit[4]: CCRC_ERR_DS1 mask bit[5]: YCS_ERR_DS1 mask bit[6]: CCS_ERR_DS1 mask bit[7]: Reserved bit[8]: AP_CRC_ERR mask bit[9]: FF_CRC_ERR mask bit[10]: VD_STD_ERR_DS1 mask 038h ERROR_MASK_2 RSVD 15-7 Reserved. ERROR_MASK_2 6-0 Error mask for global error vector (3G Level B Data Stream 2 only): bit[0]: EAV_ERR_DS2 mask bit[1]: SAV_ERR_DS2 mask bit[2]: LNUM_ERR_DS2 mask bit[3]: YCRC_ERR_DS2 mask bit[4]: CCRC_ERR_DS2 mask bit[5]: YCS_ERR_DS2 mask bit[6]: CCS_ERR_DS2 mask 039h AGC_CTRL RSVD 15-5 Reserved. SCLK_INV 4 Invert polarity of output serial audio clock. R/W 0 AMCLK_INV 3 Invert polarity of output audio master clock. R/W 0 RSVD 2 Reserved. R/W 0 Audio Master Clock Select. R/W 0 AMCLK_SEL 1-0 0: 128 fs 1: 256 fs 2: 512 fs 03Ah -6Bh RSVD RSVD 15-0 Reserved. R 0 06Ch CLK_GEN RSVD 15-6 Reserved. R/W 0 Choses between the in-phase (0) and quadrature (1) clocks for DDR mode. R/W 0 Controls the offset for the delay line. R/W 0 DEL_LINE_CLK_SEL 5 DEL_LINE_OFFSET 4-0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 105 of 145 Table 4-29: Video Core Configuration and Status Registers (Continued) Address Register Name 06Dh IO_DRIVE _STRENGTH Bit Name Bit Description R/W Default RSVD 15-6 Reserved. R/W 0 IO_DS_CTRL_DOUT_MSB 5-4 Drive strength adjustment for DOUT[19:10] outputs and PCLK output: R/W 2 R/W 2 R/W 3 00: 4mA; 01: 8mA; 10: 10mA(1.8V), 12mA(3.3V); 11: 12mA(1.8V), 16mA(3.3V) IO_DS_CTRL_STAT 3-2 Drive strength adjustment for STAT[5:0] outputs: 00: 4mA; 01: 6mA; 10: 8mA(1.8V), 10mA(3.3V); 11: 10mA(1.8V), 12mA(3.3V) IO_DS_CTRL_DOUT_LSB 1-0 Drive strength adjustment for DOUT[9:0] outputs: 00: 4mA; 01: 6mA; 10: 8mA(1.8V), 10mA(3.3V); 11: 10mA(1.8V), 12mA(3.3V) 06Eh RSVD RSVD 15-0 Reserved. R/W 0 06Fh RSVD RSVD 15-4 Reserved. R/W 0 M_DETECTION _TOLERANCE 3-0 Sets the detection tolerance. R/W 2 RSVD 15-0 Reserved. R/W 0 M_DETECTION _TOLERANCE 070h -085h RSVD GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 106 of 145 4.21.2 SD Audio Core Registers NOTE: The GS2970 only accepts write/read commands to/from the SD Audio Register Map when the audio core is locked to the incoming SD video format. Table 4-30: SD Audio Core Configuration and Status Registers Address Register Name 400h CFG_AUD Bit Name RSVD Bit 15-14 Description R/W Default Reserved. R/W 0 ALL_DEL 13 Selects deletion of all audio data and all audio control packets. 0: Do not delete existing audio packets 1: Delete existing audio packets R/W 0 MUTE_ALL 12 Mute all output channels. 0: Normal 1: Muted R/W 0 ACS_USE_SECOND 11 Extract Audio Channel Status from second channel pair. R/W 0 CLEAR_AUDIO 10 Clears all audio FIFO buffers and puts them in start-up state. R/W 0 OS_SEL 9-8 Specifies the audio FIFO buffer size. 00: 36 samples deep, 26 sample start-up count 01: 22 samples deep, 12 sample start-up count 10: 16 samples deep, 6 sample start-up count 11: Reserved R/W 0 LSB_FIRSTD 7 Causes the channel 7 and 8 output format to use LSB first. 0: MSB first 1: LSB first R/W 0 LSB_FIRSTC 6 Causes the channel 5 and 6 output format to use LSB first. 0: MSB first 1: LSB first R/W 0 LSB_FIRSTB 5 Causes the channel 3 and 4 output format to use LSB first. 0: MSB first 1: LSB first R/W 0 LSB_FIRSTA 4 Causes the channel 1 and 2 output format to use LSB first. 0: MSB first 1: LSB first R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 107 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 400h CFG_AUD Bit Name Bit Description R/W Default IDB 3-2 Specifies the Secondary audio group to extract. 00: Audio group #1 01: Audio group #2 10: Audio group #3 11: Audio group #4 Note: Should IDA and IDB be set to the same value, they automatically revert to their default values. R/W 1 IDA 1-0 Specifies the Primary audio group to extract. R/W 0 00: Audio group #1 01: Audio group #2 10: Audio group #3 11: Audio group #4 Note: Should IDA and IDB be set to the same value, they automatically revert to their default values. 401h DBN_ERR EXT_DET3_4B 15 Set when Secondary group channels 3 and 4 have extended data. Write `1' to clear. ROCW 0 EXT_DET1_2B 14 Set when Secondary group channels 1 and 2 have extended data. Write `1' to clear. ROCW 0 EXT_DET3_4A 13 Set when Primary group channels 3 and 4 have extended data. Write `1' to clear. ROCW 0 EXT_DET1_2A 12 Set when Primary group channels 1 and 2 have extended data. Write `1' to clear. ROCW 0 CTL_DBNB_ERR 11 Set when Secondary group control packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 CTL_DBNA_ERR 10 Set when Primary group control packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 EXT_DBNB_ERR 9 Set when Secondary group extended data packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 EXT_DBNA_ERR 8 Set when Primary group extended data packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 108 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 401h DBN_ERR 402h REGEN Bit Name Bit Description R/W Default SAMP_DBNB_ERR 7 Set when Secondary group data packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 SAMP_DBNA_ERR 6 Set when Primary group data packet Data Block Number sequence is discontinuous. Write `1' to clear. ROCW 0 CTRB_DET 5 Set when Secondary group audio control packet is detected. Write `1' to clear. ROCW 0 CTRA_DET 4 Set when Primary group audio control packet is detected. Write `1' to clear. ROCW 0 ACS_DET3_4B 3 Secondary group audio status detected for channels 3 and 4. Write `1' to clear. ROCW 0 ACS_DET1_2B 2 Secondary group audio status detected for channels 1 and 2. Write `1' to clear. ROCW 0 ACS_DET3_4A 1 Primary group audio status detected for channels 3 and 4. Write `1' to clear. ROCW 0 ACS_DET1_2A 0 Primary group audio status detected for channels 1 and 2. Write `1' to clear. ROCW 0 Reserved. R/W 0 RSVD 15-2 ACS_APPLY 1 Cause channel status data in ACSR[183:0] to be transferred to the channel status replacement mechanism. The transfer does not occur until the next status boundary. R/W 0 ACS_REGEN 0 Specifies that Audio Channel Status of all channels should be replaced with ACSR[183:0] field. 0: Do not replace Channel Status 1: Replace Channel Status of all channels R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 109 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 403h AUD_DET 404h CSUM_ERR_DET Bit Name CH_MUTE Description R/W Default IDB_READBACK 15-14 Actual value of IDB in the hardware. R 1 IDA_READBACK 13-12 Actual value of IDA in the hardware. R 0 XDPG4_DET 11 Set while embedded Group 4 audio extended packets are detected. R 0 XDPG3_DET 10 Set while embedded Group 3 audio extended packets are detected. R 0 XDPG2_DET 9 Set while embedded Group 2 audio extended packets are detected. R 0 XDPG1_DET 8 Set while embedded Group 1 audio extended packets are detected. R 0 ADPG4_DET 7 Set while Group 4 audio data packets are detected. R 0 ADPG3_DET 6 Set while Group 3 audio data packets are detected. R 0 ADPG2_DET 5 Set while Group 2 audio data packets are detected. R 0 ADPG1_DET 4 Set while Group 1 audio data packets are detected. R 0 ACS_APPLY_WAITD 3 Set while output channels 7 and 8 are waiting for a status boundary to apply the ACSR[183:0] data. R 0 ACS_APPLY_WAITC 2 Set while output channels 5 and 6 are waiting for a status boundary to apply the ACSR[183:0] data. R 0 ACS_APPLY_WAITB 1 Set while output channels 3 and 4 are waiting for a status boundary to apply the ACSR[183:0] data. R 0 ACS_APPLY_WAITA 0 Set while output channels 1 and 2 are waiting for a status boundary to apply the ACSR[183:0] data. R 0 R/W 0 ROCW 0 RSVD CSUM_ERROR 405h Bit 15-1 0 Reserved. Embedded packet checksum error detected. Write `1' to clear. RSVD 15-8 Reserved. R/W 0 MUTE 7-0 Mute output channels 8..1 Where bits 7:0 = channel 8:1 1: Mute 0: Normal R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 110 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 406h CH_VALID 407h SD_AUDIO_ERR OR_MASK Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 CH4_VALIDB 7 Secondary group channel 4 sample validity flag. R 0 CH3_VALIDB 6 Secondary group channel 3 sample validity flag. R 0 CH2_VALIDB 5 Secondary group channel 2 sample validity flag. R 0 CH1_VALIDB 4 Secondary group channel 1 sample validity flag. R 0 CH4_VALIDA 3 Primary group channel 4 sample validity flag. R 0 CH3_VALIDA 2 Primary group channel 3 sample validity flag. R 0 CH2_VALIDA 1 Primary group channel 2 sample validity flag. R 0 CH1_VALIDA 0 Primary group channel 1 sample validity flag. R 0 RSVD 15 Reserved. R/W 0 EN_NOT_LOCKED 14 Asserts interrupt when LOCKED signal is not asserted. R/W 0 EN_NO_VIDEO 13 Asserts interrupt when video format is unknown. R/W 0 EN_CSUM_ERROR 12 Asserts interrupt when checksum error is detected. R/W 0 EN_ACS_DET3_4B 11 Asserts interrupt when EN_ACS_DET3_4B flag is set. R/W 0 EN_ACS_DET1_2B 10 Asserts interrupt when EN_ACS_DET1_2B flag is set. R/W 0 EN_ACS_DET3_4A 9 Asserts interrupt when EN_ACS_DET3_4A flag is set. R/W 0 EN_ACS_DET1_2A 8 Asserts interrupt when EN_ACS_DET1_2A flag is set. R/W 0 EN_CTRB_DET 7 Asserts interrupt when EN_CTRB_DET flag is set. R/W 0 EN_CTRA_DET 6 Asserts interrupt when EN_CTRA_DET flag is set. R/W 0 EN_DBNB_ERR 5 Asserts interrupt when EN_DBNB_ERR flag is set. R/W 0 EN_DBNA_ERR 4 Asserts interrupt when EN_DBNA_ERR flag is set. R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 111 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name 407h SD_AUDIO_ERR OR_MASK EN_ADPG4_DET 408h CFG_OUTPUT Bit Description R/W Default 3 Asserts interrupt when the ADPG4_DET flag is set. R/W 0 EN_ADPG3_DET 2 Asserts interrupt when the ADPG3_DET flag is set. R/W 0 EN_ADPG2_DET 1 Asserts interrupt when the ADPG2_DET flag is set. R/W 0 EN_ADPG1_DET 0 Asserts interrupt when the ADPG1_DET flag is set. R/W 0 ASWLD 15-14 Output channels 7 and 8 word length. 00: 24 bits 01: 20 bits 10: 16 bits 11: Automatic 20-bit or 24-bit R/W 3 ASWLC 13-12 Output channels 5 and 6 word length. (See above for decoding) R/W 3 ASWLB 11-10 Output channels 3 and 4 word length. (See above for decoding) R/W 3 ASWLA 9-8 Output channels 1 and 2 word length. (See above for decoding) R/W 3 AMD 7-6 Output channels 7 and 8 format selector. 00: AES/EBU audio output 01: Serial audio output: Left justified; MSB first 10: Serial audio output: Right justified; MSB first R/W 3 11: I2S serial audio output AMC 5-4 Output channels 5 and 6 format selector. (See above for decoding). R/W 3 AMB 3-2 Output channels 3 and 4 format selector. (See above for decoding). R/W 3 AMA 1-0 Output channels 1 and 2 format selector. (See above for decoding). R/W 3 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 112 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 409h OUTPUT_SEL_1 40Ah 40Bh 41Fh OUTPUT_SEL_2 RSVD Bit Name Bit Description R/W Default RSVD 15-12 Reserved. R/W 0 OP4_SRC 11-9 Output channel 4 source selector. 000: Primary audio group channel 1 001: Primary audio group channel 2 010: Primary audio group channel 3 011: Primary audio group channel 4 100: Secondary audio group channel 1 101: Secondary audio group channel 2 110: Secondary audio group channel 3 111: Secondary audio group channel 4 R/W 3 OP3_SRC 8-6 Output channel 3 source selector (Decode as above). R/W 2 OP2_SRC 5-3 Output channel 2 source selector (Decode as above). R/W 1 OP1_SRC 2-0 Output channel 1 source selector (Decode as above). R/W 0 RSVD 15-12 Reserved. R/W 0 OP8_SRC 11-9 Output channel 8 source selector. 000: Primary audio group channel 1 001: Primary audio group channel 2 010: Primary audio group channel 3 011: Primary audio group channel 4 100: Secondary audio group channel 1 101: Secondary audio group channel 2 110: Secondary audio group channel 3 111: Secondary audio group channel 4 R/W 7 OP7_SRC 8-6 Output channel 7 source selector (Decode as above). R/W 6 OP6_SRC 5-3 Output channel 6 source selector (Decode as above). R/W 5 OP5_SRC 2-0 Output channel 5 source selector (Decode as above). R/W 4 - - RSVD GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 - Reserved. 113 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 420h AFNA12 421h 422h 423h 424h AFNA34 RATEA ACT_A PRIM_AUD_ DELAY_1 Bit Name Bit Description R/W Default RSVD 15-9 Reserved. R/W 0 AFN1_2A 8-0 Primary group audio frame number for channels 1 and 2. R 0 RSVD 15-9 Reserved. R/W 0 AFN3_4A 8-0 Primary group audio frame number for channels 3 and 4. R 0 RSVD 15-8 Reserved. R/W 0 RATE3_4A 7-5 Primary group sampling frequency for channels 3 and 4 R 0 ASX3_4A 4 Primary group asynchronous mode for channels 3 and 4. R 0 RATE1_2A 3-1 Primary group sampling frequency for channels 1 and 2. R 0 ASX1_2A 0 Primary group asynchronous mode for channels 1 and 2. R 0 R/W 0 R 0 R/W 0 RSVD 15-4 Reserved. ACTA 3-0 Primary group active channels. RSVD 15-9 Reserved. DEL1A_1 8-1 Primary Audio group delay data for channel 1. R 0 0 Primary Audio group delay data valid flag for channel 1. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT1A 425h 426h 427h PRIM_AUD_ DELAY_2 RSVD 15-9 Reserved. DEL1A_2 8-0 Primary Audio group delay data for channel 1. PRIM_AUD_ DELAY_3 RSVD 15-9 Reserved. DEL1A_3 8-0 Primary Audio group delay data for channel 1. PRIM_AUD_ DELAY_4 RSVD 15-9 Reserved. DEL2A_4 8-1 Primary Audio group delay data for channel 2. R 0 0 Primary Audio group delay data valid flag for channel 2. R 0 R/W 0 R 0 R/W 0 R 0 EBIT2A 428h 429h PRIM_AUD_ DELAY_5 RSVD 15-9 Reserved. DEL2A_5 8-0 Primary Audio group delay data for channel 2. PRIM_AUD_ DELAY_6 RSVD 15-9 Reserved. DEL2A_6 8-0 Primary Audio group delay data for channel 2. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 114 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 42Ah PRIM_AUD_ DELAY_7 Bit Name Bit Description R/W Default RSVD 15-9 Reserved. R/W 0 DEL3A_7 8-1 Primary Audio group delay data for channel 3. R 0 0 Primary Audio group delay data valid flag for channel 3. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT3A 42Bh 42Ch 42Dh PRIM_AUD_ DELAY_8 RSVD 15-9 Reserved. DEL3A_8 8-0 Primary Audio group delay data for channel 3. PRIM_AUD_ DELAY_9 RSVD 15-9 Reserved. DEL3A_9 8-0 Primary Audio group delay data for channel 3. PRIM_AUD_ DELAY_10 RSVD 15-9 Reserved. DEL4A_10 8-1 Primary Audio group delay data for channel 4. R 0 0 Primary Audio group delay data valid flag for channel 4. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT4A 42Eh 42Fh 430h 431h 432h 433h PRIM_AUD_ DELAY_11 RSVD 15-9 Reserved. DEL4A_11 8-0 Primary Audio group delay data for channel 4. PRIM_AUD_ DELAY_12 RSVD 15-9 Reserved. DEL4A_12 8-0 Primary Audio group delay data for channel 4. AFNB12 RSVD 15-9 Reserved. AFN1_2B 8-0 Secondary group audio frame number for channels 1 and 2. RSVD 15-9 Reserved. AFN3_4B 8-0 Secondary group audio frame number for channels 3 and 4. R 0 RSVD 15-8 Reserved. R 0 RATE3_4B 7-5 Secondary group sampling frequency for channels 3 and 4. R 0 ASX3_4B 4 Secondary group asynchronous mode for channels 3 and 4. R 0 RATE1_2B 3-1 Secondary group sampling frequency for channels 1 and 2. R 0 ASX1_2B 0 Secondary group asynchronous mode for channels 1 and 2. R 0 R/W 0 R 0 AFNB34 RATEB ACT_B RSVD 15-4 Reserved. ACTB 3-0 Secondary group active channels. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 115 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 434h SEC_AUD_ DELAY_! Bit Name Bit Description R/W Default RSVD 15-9 Reserved. R/W 0 DEL1B_1 8-1 Secondary Audio group delay data for channel 1. R 0 0 Secondary Audio group delay data valid flag for channel 1. R 0 EBIT1B 435h 436h 437h SEC_AUD DELAY_2 RSVD 15-9 Reserved. DEL1B_2 8-0 Secondary Audio group delay data for channel 1. SEC_AUD_ DELAY_3 RSVD 15-9 Reserved. DEL1B_3 8-0 Secondary Audio group delay data for channel 1. SEC_AUD DELAY_4 RSVD 15-9 Reserved. DEL2B_4 8-1 0 EBIT2B 438h 439h 43Ah 43Ch 43Dh R 0 R/W 0 R 0 R/W 0 Secondary Audio group delay data for channel 2. R 0 Secondary Audio group delay data valid flag for channel 2. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 SEC_AUD DELAY_5 RSVD 15-9 Reserved. DEL2B_5 8-0 Secondary Audio group delay data for channel 2. SEC_AUD DELAY_6 RSVD 15-9 Reserved. DEL2B_6 8-0 Secondary Audio group delay data for channel 2. SEC_AUD DELAY_7 RSVD 15-9 Reserved. DEL3B_7 8-1 Secondary Audio group delay data for channel 3. R 0 0 Secondary Audio group delay data valid flag for channel 3. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT3B 43Bh R/W SEC_AUD DELAY_8 RSVD 15-9 Reserved. DEL3B_8 8-0 Secondary Audio group delay data for channel 3. SEC_AUD DELAY_9 RSVD 15-9 Reserved. DEL3B_9 8-0 Secondary Audio group delay data for channel 3. SEC_AUD DELAY_10 RSVD 15-9 Reserved. DEL4B_10 8-1 Secondary Audio group delay data for channel 4. R 0 0 Secondary Audio group delay data valid flag for channel 4. R 0 EBIT4B GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 116 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name 43Eh 43Fh Bit Name Bit Description R/W Default SEC_AUD_ DELAY_11 RSVD 15-9 Reserved. R/W 0 DEL4B_11 8-0 Secondary Audio group delay data for channel 4. R 0 SEC_AUD_ DELAY_12 RSVD 15-9 Reserved. R/W 0 DEL4B_12 8-0 Secondary Audio group delay data for channel 4. R 0 440h ACSR1_2A_BYTE 0_1 ACSR1_2A_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group A channel status for channels 1 and 2 R 0 441h ACSR1_2A_BYTE 2_3 ACSR1_2A_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group A channel status for channels 1 and 2 R 0 442h ACSR1_2A_BYTE 4_5 ACSR1_2A_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group A channel status for channels 1 and 2 R 0 443h ACSR1_2A_BYTE 6_7 ACSR1_2A_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group A channel status for channels 1 and 2 R 0 444h ACSR1_2A_BYTE 8_9 ACSR1_2A_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group A channel status for channels 1 and 2. R 0 445H ACSR1_2A_BYTE 10_11 ACSR1_2A_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group A channel status for channels 1 and 2. R 0 446H ACSR1_2A_BYTE 12_13 ACSR1_2A_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group A channel status for channels 1 and 2. R 0 447h ACSR1_2A_BYTE 14_15 ACSR1_2A_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group A channel status for channels 1 and 2. R 0 448h ACSR1_2A_BYTE 16_17 ACSR1_2A_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group A channel status for channels 1 and 2. R 0 449h ACSR1_2A_BYTE 18_19 ACSR1_2A_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group A channel status for channels 1 and 2. R 0 44Ah ACSR1_2A_BYTE 20_21 ACSR1_2A_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group A channel status for channels 1 and 2. R 0 44Bh ACRS1_2A_ BYTE22 RSVD 15-8 Reserved. R/W 0 ACSR1_2A_22 7-0 Bytes 22 of audio group A channel status for channels 1 and 2. R 0 RSVD RSVD 15-0 Reserved. R/W 0 44Ch 44Fh GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 117 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 450h ACSR3_4A BYTE0_1 ACSR3_4A_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group A channel status for channels 3 and 4. R 0 451h ACSR3_4A BYTE2_3 ACSR3_4A_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group A channel status for channels 3 and 4. R 0 452h ACSR3_4A_BYTE 4_5 ACSR3_4A_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group A channel status for channels 3 and 4. R 0 453h ACSR3_4A_BYTE 6_7 ACSR3_4A_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group A channel status for channels 3 and 4. R 0 454h ACSR3_4A_BYTE 8_9 ACSR3_4A_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group A channel status for channels 3 and 4. R 0 455h ACSR3_4A_BYTE 10_11 ACSR3_4A_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group A channel status for channels 3 and 4. R 0 456h ACSR3_4A_BYTE 12_13 ACSR3_4A_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group A channel status for channels 3 and 4. R 0 457h ACSR3_4A_BYTE 14_15 ACSR3_4A_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group A channel status for channels 3 and 4. R 0 458h ACSR3_4A_BYTE 16_17 ACSR3_4A_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group A channel status for channels 3 and 4. R 0 459h ACSR3_4A_BYTE 18_19 ACSR3_4A_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group A channel status for channels 3 and 4. R 0 45Ah ACSR3_4A_BYTE 20_21 ACSR3_4A_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group A channel status for channels 3 and 4. R 0 45Bh ACSR3_4A_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR3_4A_22 7-0 Bytes 22 of audio group A channel status for channels 3 and 4. R 0 RSVD RSVD 15-0 Reserved. R/W 0 460h ACSR1_2B_BYTE 0_1 ACSR1_2B_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group B channel status for channels 1 and 2. R 0 461h ACSR1_2B_BYTE 2_3 ACSR1_2B_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group B channel status for channels 1 and 2. R 0 462h ACSR1_2B_BYTE 4_5 ACSR1_2B_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group B channel status for channels 1 and 2. R 0 45Ch 45Fh GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 118 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 463h ACSR1_2B_BYTE 6_7 ACSR1_2B_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group B channel status for channels 1 and 2. R 0 464h ACSR1_2B_BYTE 8_9 ACSR1_2B_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group B channel status for channels 1 and 2. R 0 465h ACSR1_2B_BYTE 10_11 ACSR1_2B_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group B channel status for channels 1 and 2. R 0 466h ACSR1_2B_BYTE 12_13 ACSR1_2B_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group B channel status for channels 1 and 2. R 0 467h ACSR1_2B_BYTE 14_15 ACSR1_2B_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group B channel status for channels 1 and 2. R 0 468h ACSR1_2B_BYTE 16_17 ACSR1_2B_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group B channel status for channels 1 and 2. R 0 469h ACSR1_2B_BYTE 18_19 ACSR1_2B_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group B channel status for channels 1 and 2. R 0 46Ah ACSR1_2B_BYTE 20_21 ACSR1_2B_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group B channel status for channels 1 and 2. R 0 46Bh ACSR1_2B_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR1_2B_22 7-0 Bytes 22 of audio group B channel status for channels 1 and 2. R 0 RSVD RSVD 15-0 Reserved. R/W 0 470h ACSR3_4B_BYTE 0_1 ACSR3_4B_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group B channel status for channels 3 and 4. R 0 471h ACSR3_4B_BYTE 2_3 ACSR3_4B_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group B channel status for channels 3 and 4. R 0 472h ACSR3_4B_BYTE 4_5 ACSR3_4B_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group B channel status for channels 3 and 4. R 0 473h ACSR3_4B_BYTE 6_7 ACSR3_4B_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group B channel status for channels 3 and 4. R 0 474h ACSR3_4B_BYTE 8_9 ACSR3_4B_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group B channel status for channels 3 and 4. R 0 475h ACSR3_4B_BYTE 10_11 ACSR3_4B_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group B channel status for channels 3 and 4. R 0 46Ch 46Fh GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 119 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 476h ACSR3_4B_BYTE 12_13 ACSR3_4B_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group B channel status for channels 3 and 4. R 0 477h ACSR3_4B_BYTE 14_15 ACSR3_4B_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group B channel status for channels 3 and 4. R 0 478h ACSR3_4A_BYTE 16_17 ACSR3_4B_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group B channel status for channels 3 and 4. R 0 479h ACSR3_4A_BYTE 18_19 ACSR3_4B_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group B channel status for channels 3 and 4. R 0 47Ah ACSR3_4A_BYTE 20_21 ACSR3_4B_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group B channel status for channels 3 and 4. R 0 47Bh ACSR3_4A_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR3_4B_22 7-0 Bytes 22 of audio group B channel status for channels 3 and 4. R 0 47Ch 47Fh RSVD RSVD 15-0 Reserved. R/W 0 480h ACSR_BYTE_0 ACSR_BYTE0 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register for 23 registers. R 0 481h ACSR_BYTE_1 ACSR_BYTE1 7-0 - W 0 482h ACSR_BYTE_2 ACSR_BYTE2 7-0 - W 0 483h ACSR_BYTE_3 ACSR_BYTE3 7-0 - W 0 484h ACSR_BYTE_4 ACSR_BYTE4 7-0 - W 0 485h ACSR_BYTE_5 ACSR_BYTE5 7-0 - W 0 486h ACSR_BYTE_6 ACSR_BYTE6 7-0 - W 0 487h ACSR_BYTE_7 ACSR_BYTE7 7-0 - W 0 488h ACSR_BYTE_8 ACSR_BYTE8 7-0 - W 0 489h ACSR_BYTE_9 ACSR_BYTE9 7-0 - W 0 48Ah ACSR_BYTE_10 ACSR_BYTE10 7-0 - W 0 48Bh ACSR_BYTE_11 ACSR_BYTE11 7-0 - W 0 48Ch ACSR_BYTE_12 ACSR_BYTE12 7-0 - W 0 48Dh ACSR_BYTE_13 ACSR_BYTE13 7-0 - W 0 48Eh ACSR_BYTE_14 ACSR_BYTE14 7-0 - W 0 48Fh ACSR_BYTE_15 ACSR_BYTE15 7-0 - W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 120 of 145 Table 4-30: SD Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 490h ACSR_BYTE_16 ACSR_BYTE16 7-0 - W 0 491h ACSR_BYTE_17 ACSR_BYTE17 7-0 - W 0 492h ACSR_BYTE_18 ACSR_BYTE18 7-0 - W 0 493h ACSR_BYTE_19 ACSR_BYTE19 7-0 - W 0 494h ACSR_BYTE_20 ACSR_BYTE20 7-0 - R/W 0 495h ACSR_BYTE_21 ACSR_BYTE21 7-0 - R/W 0 496h ACSR_BYTE_22 ACSR_BYTE22 7-0 - R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 121 of 145 4.21.3 HD and 3G Audio Core Registers NOTE: The GS2970 only accepts write/read commands to/from the HD/3G Audio Register Map when the audio core is locked to the incoming HD or 3G video format. Table 4-31: HD and 3G Audio Core Configuration and Status Registers Address Register Name 200h CFG_AUD Bit Name Bit Description R/W Default ECC_OFF 15 Disables ECC error correction. R/W 0 ALL_DEL 14 Selects deletion of all audio data and all audio control packets R/W 0 R/W 0 Extract Audio Channel Status from second channel pair. R/W 0 Secondary group output word length. R/W 3 R/W 3 R/W 3 R/W 3 0: Do not delete existing audio control packets 1: Delete existing audio control packets. MUTE_ALL 13 Mute all output channels 0: Normal 1: Muted ACS_USE_SECOND ASWLB 12 11-10 00: 24 bits 01: 20 bits 10: 16 bits 11: invalid ASWLA 9-8 Primary group output word length. 00: 24 bits 01: 20 bits 10: 16 bits 11: invalid AMB 7-6 Secondary group output format selector. 00: AES/EBU audio output 01: Serial audio output: left justified MSB first 10: Serial audio output: right justified. MSB first 11: I2S serial audio output AMA 5-4 Primary group output format selector. 00: AES/EBU audio output 01: Serial audio output: left justified MSB first 10: Serial audio output: right justified MSB first 11: I2S serial audio output GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 122 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 200h CFG_AUD Bit Name Bit Description R/W Default IDB 3-2 Specifies the Secondary audio group to extract. R/W 1 R/W 0 R/W 0 00: Audio group #1 01: Audio group #2 10: Audio group #3 11: Audio group #4 Note: Should IDA and IDB be set to the same value, they automatically revert to their default values. IDA 1-0 Specifies the Primary audio group to extract. 00: Audio group #1 01: Audio group #2 10: Audio group #3 11: Audio group #4 Note: Should IDA and IDB be set to the same value, they automatically revert to their default values. 201h ACS_DET RSVD 15-8 Reserved. DBNB_ERR 7 Set when Secondary group audio Data Block Number sequence is discontinuous. ROCW 0 DBNA_ERR 6 Set when Primary group audio Data Block Number sequence is discontinuous. ROCW 0 CTRB_DET 5 Set when Secondary group audio control packet is detected. ROCW 0 CTRA_DET 4 Set when Primary group audio control packet is detected. ROCW 0 ACS_DET3_4B 3 Secondary group audio status detected for channels 3 and 4. ROCW 0 ACS_DET1_2B 2 Secondary group audio status detected for channels 1 and 2. ROCW 0 ACS_DET3_4A 1 Primary group audio status detected for channels 3 and 4. ROCW 0 ACS_DET1_2A 0 Primary group audio status detected for channels 1 and 2. ROCW 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 123 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 202h AUD_DET1 203h 204h AUD_DET2 REGEN Bit Name Bit Description R/W Default RSVD 15-9 Reserved. R 0 IDB_READBACK 8-7 Actual value of IDB in the hardware. R 1 IDA_READBACK 6-5 Actual value of IDA in the hardware. R 0 ADPG4_DET 4 Set while Group 4 audio data packets are detected. R 0 ADPG3_DET 3 Set while Group 3 audio data packets are detected. R 0 ADPG2_DET 2 Set while Group 2 audio data packets are detected. R 0 ADPG1_DET 1 Set while Group 1 audio data packets are detected. R 0 ACS_APPLY_WAIT 0 ACS_APPLY_WAIT: Set while output channels 1 and 2 are waiting for a status boundary to apply the ACSR[183:0] data. R 0 R/W 0 RSVD 15-2 Reserved. ECCA_ERROR 1 Primary group audio data packet error detected. ROCW 0 ECCB_ERROR 0 Secondary group audio data packet error detected. ROCW 0 Reserved. R/W 0 RSVD 15-2 ACS_APPLY 1 Cause channel status data in ACSR[183:0] to be transferred to the channel status replacement mechanism. The transfer does not occur until the next status boundary. R/W 0 ACS_REGEN 0 Specifies that Audio Channel Status of all channels should be replaced with ACSR[183:0] field. R/W 0 0: Do not replace Channel Status 1: Replace Channel Status of all channels 205h CH_MUTE RSVD 15 Reserved. R/W 0 MUTEB 7-4 Mute Secondary output channels 4..1 Where bits 7:4 = channel 4:1 R/W 0 R/W 0 1: Mute 0: Normal MUTEA 3-0 Mute Primary output channels 4..1 Where bits 3:0 = channel 4:1 1: Mute 0: Normal GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 124 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 206h CH_VALID Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 CH4_VALIDB 7 Secondary group channel 4 sample validity flag. R 0 CH3_VALIDB 6 Secondary group channel 3 sample validity flag. R 0 CH2_VALIDB 5 Secondary group channel 2 sample validity flag. R 0 CH1_VALIDB 4 Secondary group channel 1 sample validity flag. R 0 CH4_VALIDA 3 Primary group channel 4 sample validity flag. R 0 CH3_VALIDA 2 Primary group channel 3 sample validity flag. R 0 CH2_VALIDA 1 Primary group channel 2 sample validity flag. R 0 CH1_VALIDA 0 Primary group channel 1 sample validity flag. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 125 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 207h HD_AUDIO_ERR OR_MASK RSVD 15 Reserved. R/W 0 EN_MISSING_PHASE 14 Asserts AUDIO_ERROR when chosen group's phase data is missing R/W 0 EN_ACS_DET3_4B 13 Asserts AUDIO_ERROR when ACS_DET3_4B flag is set. R/W 0 EN_ACS_DET1_2B 12 Asserts AUDIO_ERROR when ACS_DET1_2B flag is set. R/W 0 EN_ACS_DET3_4A 11 Asserts AUDIO_ERROR when ACS_DET3_4A flag is set. R/W 0 EN_ACS_DET1_2A 10 Asserts AUDIO_ERROR when ACS_DET1_2A flag is set. R/W 0 EN_CTRB_DET 9 Asserts AUDIO_ERROR when CTRB_DET flag is set. R/W 0 EN_CTRA_DET 8 Asserts AUDIO_ERROR when CTRA_DET flag is set. R/W 0 EN_DBNB_ERR 7 Asserts AUDIO_ERROR when DBNB_ERR flag is set. R/W 0 EN_DBNA_ERR 6 Asserts AUDIO_ERROR when DBNA_ERR flag is set. R/W 0 EN_ECCB_ERR 5 Asserts AUDIO_ERROR when ECCB_ERR flag is set. R/W 0 EN_ECCA_ERR 4 Asserts AUDIO_ERROR when ECCA_ERR flag is set. R/W 0 EN_ADPG4_DET 3 Asserts AUDIO_ERROR when ADPG4_DET flag is set. R/W 0 EN_ADPG3_DET 2 Asserts AUDIO_ERROR when ADPG3_DET flag is set. R/W 0 EN_ADPG2_DET 1 Asserts AUDIO_ERROR when ADPG2_DET flag is set. R/W 0 EN_ADPG1_DET 0 Asserts AUDIO_ERROR when ADPG1_DET flag is set. R/W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 126 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 208h CFG_AUD_2 Bit Name RSVD Bit 15-11 Description R/W Default Reserved. R/W 0 SEL_PHASE_SRC 10 Selects between the Primary and Secondary embedded phase info. R/W 0 LSB_FIRSTB 9 Causes the Secondary group serial output formats to use LSB first. R/W 0 LSB_FIRSTA 8 Causes the Primary group serial output formats to use LSB first. R/W 0 FORCE_M 7 Disables M value detection and forces M value to that specified by FORCE_MEQ1001. R/W 0 FORCE_MEQ1001 6 Specifies M value when FORCE_M is set. R/W 0 1: M= 1.001 0: M = 1.000 209h CFG_AUD_3 IGNORE_PHASE 5 Causes the Demultiplexer to ignore the embedded clock info in both the Primary and Secondary group audio data packets. Clock is generated based on the video format and M value. R/W 0 FORCE_ACLK128 4 Causes the core to ignore embedded clock info and derive phase information from ACLK128. R/W 0 EN_NOT_LOCKED 3 Asserts AUDIO_ERROR when locked is not asserted. R/W 0 EN_NO_VIDEO 2 Asserts AUDIO_ERROR when the video format is unknown. R/W 0 EN_NO_PHASEB 1 Asserts AUDIO_ERROR when NO_PHASEB_DATA is set. R/W 0 EN_NO_PHASEA 0 Asserts AUDIO_ERROR when NO_PHASEA_DATA is set. R/W 0 Reserved. R/W 0 RSVD 15-3 MISSING_PHASE 2 Embedded phase info for chosen group missing or incorrect. R 0 NO_PHASEB_DATA 1 Secondary group has invalid embedded clock information. R 0 NO_PHASEA_DATA 0 Primary group has invalid embedded clock information. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 127 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 20Ah OUTPUT_SEL_1 Bit Name Bit Description RSVD 15-12 Reserved. OP4_SRC 11-9 Output channel 4 source selector. R/W Default R 0 R/W 3 000: Primary audio group channel 1 001: Primary audio group channel 2 010: Primary audio group channel 3 011: Primary audio group channel 4 100: Secondary audio group channel 1 101: Secondary audio group channel 2 110: Secondary audio group channel 3 111: Secondary audio group channel 4 20Bh OUTPUT_SEL_2 OP3_SRC 8-6 Output channel 3 source selector (Decode as above). R/W 2 OP2_SRC 5-3 Output channel 2 source selector (Decode as above). R/W 1 OP1_SRC 2-0 Output channel 1 source selector (Decode as above). R/W 0 RSVD 15-12 Reserved. R/W 0 OP8_SRC 11-9 Output channel 8 source selector. R/W 7 000: Primary audio group channel 1 001: Primary audio group channel 2 010: Primary audio group channel 3 011: Primary audio group channel 4 100: Secondary audio group channel 1 101: Secondary audio group channel 2 110: Secondary audio group channel 3 111: Secondary audio group channel 4 OP7_SRC 8-6 Output channel 7 source selector (Decode as above). R/W 6 OP6_SRC 5-3 Output channel 6 source selector (Decode as above). R/W 5 OP5_SRC 2-0 Output channel 5 source selector (Decode as above). R/W 4 20Ch 21Fh RSVD RSVD - Reserved. - - 220h AFNA RSVD 15-9 Reserved. R/W 0 AFNA 8-0 Primary group audio frame number. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 128 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 221h RATEA 222h 223h ACTA PRIM_AUD _DELAY_1 Bit Name Bit Description R/W Default RSVD 15-4 Reserved. R/W 0 RATEA 3-1 Primary group sampling frequency for channels 1 and 2. R 0 ASXA 0 Primary group asynchronous mode for channels 1 and 2. R 0 RSVD 15-4 Reserved. R/W 0 ACTA 3-0 Primary group active channels. R 0 RSVD 15-9 Reserved. R/W 0 DEL1_2A_1 8-1 Primary Audio group delay data for channels 1 and 2 [7:0]. R 0 Primary Audio group delay data valid flag for channels 1 and 2. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT1_2A 224h 225h 226h PRIM_AUD _DELAY_2 PRIM_AUD _DELAY_3 PRIM_AUD _DELAY_4 RSVD 15-9 Reserved. DEL1_2A_2 8-0 Primary Audio group delay data for channels 1 and 2 [16:8]. RSVD 15-9 Reserved. DEL1_2A_3 8-0 Primary Audio group delay data for channels 1 and 2 [25:17]. RSVD 15-9 Reserved. DEL3_4A_4 8-1 Primary Audio group delay data for channels 3 and 4 [7:0]. R 0 Primary Audio group delay data valid flag for channels 3 and 4. R 0 R/W 0 R 0 R/W 0 R 0 EBIT3_4A 227h 228h PRIM_AUD _DELAY_5 PRIM_AUD _DELAY_6 0 0 RSVD 15-9 Reserved. DEL3_4A_5 8-0 Primary Audio group delay data for channels 3 and 4 [16:8]. RSVD 15-9 Reserved. DEL3_4A_6 8-0 Primary Audio group delay data for channels 3 and 4 [25:17]. 229h 22Fh RSVD RSVD - Reserved. R/W 0 230h AFNB RSVD 15-9 Reserved. R/W 0 AFNB 8-0 Secondary group audio frame number. R 0 RSVD 15-4 Reserved. R/W 0 RATEB 3-1 Secondary group sampling frequency for channels 1 and 2. R 0 ASXB 0 Secondary group asynchronous mode for channels 1 and 2. R 0 231h RATEB GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 129 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 232h ACTB 233h SEC_AUD_DELAY _1 Bit Name Bit Description R/W Default RSVD 15-4 Reserved. R/W 0 ACTB 3-0 Secondary group active channels. R 0 RSVD 15-9 Reserved. R/W 0 DEL1_2B_1 8-1 Secondary Audio group delay data valid flag for channels 1 and 2. R 0 0 Secondary Audio group delay data for channels 1 and 2 [7:0]. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT1_2B 234h 235h 236h SEC_AUD_DELAY _2 SEC_AUD_DELAY _3 SEC_AUD_DELAY _4 RSVD 15-9 Reserved. DEL1_2B_2 8-0 Secondary Audio group delay data for channels 1 and 2 [16:8]. RSVD 15-9 Reserved. DEL1_2B_3 8-0 Secondary Audio group delay data for channels 1 and 2 [25:17]. RSVD 15-9 Reserved. DEL3_4B_4 8-1 Secondary Audio group delay data for channels 3 and 4 [7:0]. R 0 0 Secondary Audio group delay data valid flag for channels 3 and 4. R 0 R/W 0 R 0 R/W 0 R 0 R/W 0 EBIT3_4B 237h 238h SEC_AUD_DELAY _5 SEC_AUD_DELAY _6 RSVD 15-9 Reserved. DEL3_4B_5 8-0 Secondary Audio group delay data for channels 3 and 4 [16:8]. RSVD 15-9 Reserved. DEL3_4B_6 8-0 Secondary Audio group delay data for channels 3 and 4 [25:17]. RSVD - 239h 23Fh RSVD 240h ACSR1_2A_BYTE 0_1 ACSR1_2A_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group A channel status for channels 1 and 2. R 0 241h ACSR1_2A_BYTE 2_3 ACSR1_2A_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group A channel status for channels 1 and 2. R 0 242h ACSR1_2A_BYTE 4_5 ACSR1_2A_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group A channel status for channels 1 and 2. R 0 243h ACSR1_2A_BYTE 6_7 ACSR1_2A_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group A channel status for channels 1 and 2. R 0 244h ACSR1_2A_BYTE 8_9 ACSR1_2A_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group A channel status for channels 1 and 2. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 Reserved. 130 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 245h ACSR1_2A_BYTE 10_11 ACSR1_2A_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group A channel status for channels 1 and 2. R 0 246h ACSR1_2A_BYTE 12_13 ACSR1_2A_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group A channel status for channels 1 and 2. R 0 247h ACSR1_2A_BYTE 14_15 ACSR1_2A_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group A channel status for channels 1 and 2. R 0 248h ACSR1_2A_BYTE 16_17 ACSR1_2A_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group A channel status for channels 1 and 2. R 0 249h ACSR1_2A_BYTE 18_19 ACSR1_2A_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group A channel status for channels 1 and 2. R 0 24Ah ACSR1_2A_BYTE 20_21 ACSR1_2A_20 15-0 Bytes 20 and 21 of audio group A channel status for channels 1 and 2. R 0 24Bh ACSR1_2A_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR1_2A_22 7-0 Bytes 22 of audio group A channel status for channels 1 and 2. R 0 RSVD 15-0 Reserved. R/W 0 24Ch 24Fh RSVD 250h ACSR3_4A_BYTE 0_1 ACSR3_4A_0 15-0 Bytes 0 [7:0] and 1 of audio group A channel status for channels 3 and 4. R 0 251h ACSR3_4A_BYTE 2_3 ACSR3_4A_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group A channel status for channels 3 and 4. R 0 252h ACSR3_4A_BYTE 4_5 ACSR3_4A_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group A channel status for channels 3 and 4. R 0 253h ACSR3_4A_BYTE 6_7 ACSR3_4A_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group A channel status for channels 3 and 4. R 0 254h ACSR3_4A_BYTE 8_9 ACSR3_4A_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group A channel status for channels 3 and 4. R 0 255h ACSR3_4A_BYTE 10_11 ACSR3_4A_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group A channel status for channels 3 and 4. R 0 256h ACSR3_4A_BYTE 12_13 ACSR3_4A_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group A channel status for channels 3 and 4. R 0 257h ACSR3_4A_BYTE 14_15 ACSR3_4A_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group A channel status for channels 3 and 4. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 131 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 258h ACSR3_4A_BYTE 16_17 ACSR3_4A_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group A channel status for channels 3 and 4. R 0 259h ACSR3_4A_BYTE 18_19 ACSR3_4A_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group A channel status for channels 3 and 4. R 0 25Ah ACSR3_4A_BYTE 20_21 ACSR3_4A_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group A channel status for channels 3 and 4. R 0 25Bh ACSR3_4A_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR3_4A_22 7-0 Bytes 22 of audio group A channel status for channels 3 and 4. R 0 RSVD 15-0 Reserved. R/W 0 25Ch 25Fh RSVD 260h ACSR1_2B_BYTE 0_1 ACSR1_2B_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group B channel status for channels 1 and 2. R 0 261h ACSR1_2B_BYTE 2_3 ACSR1_2B_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group B channel status for channels 1 and 2. R 0 262h ACSR1_2B_BYTE 4_5 ACSR1_2B_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group B channel status for channels 1 and 2. R 0 263h ACSR1_2B_BYTE 6_7 ACSR1_2B_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group B channel status for channels 1 and 2. R 0 264h ACSR1_2B_BYTE 8_9 ACSR1_2B_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group B channel status for channels 1 and 2. R 0 265h ACSR1_2B_BYTE 10_11 ACSR1_2B_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group B channel status for channels 1 and 2. R 0 266h ACSR1_2B_BYTE 12_13 ACSR1_2B_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group B channel status for channels 1 and 2. R 0 267h ACSR1_2B_BYTE 14_15 ACSR1_2B_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group B channel status for channels 1 and 2. R 0 268h ACSR1_2B_BYTE 16_17 ACSR1_2B_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group B channel status for channels 1 and 2. R 0 269h ACSR1_2B_BYTE 18_19 ACSR1_2B_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group B channel status for channels 1 and 2. R 0 26Ah ACSR1_2B_BYTE 20_21 ACSR1_2B_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group B channel status for channels 1 and 2. R 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 132 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name Bit Name Bit Description R/W Default 26Bh ACSR1_2B_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR1_2B_22 7-0 Bytes 22 of audio group B channel status for channels 1 and 2. R 0 RSVD 15-0 Reserved. R/W 0 26Ch 26Fh RSVD 270h ACSR3_4B_BYTE 0_1 ACSR3_4B_0 15-0 Bytes 0 [7:0] and 1 [15:8] of audio group B channel status for channels 3 and 4. R 0 271h ACSR3_4B_BYTE 2_3 ACSR3_4B_2 15-0 Bytes 2 [7:0] and 3 [15:8] of audio group B channel status for channels 3 and 4. R 0 272h ACSR3_4B_BYTE 4_5 ACSR3_4B_4 15-0 Bytes 4 [7:0] and 5 [15:8] of audio group B channel status for channels 3 and 4. R 0 273h ACSR3_4B_BYTE 6_7 ACSR3_4B_6 15-0 Bytes 6 [7:0] and 7 [15:8] of audio group B channel status for channels 3 and 4. R 0 274h ACSR3_4B_BYTE 8_9 ACSR3_4B_8 15-0 Bytes 8 [7:0] and 9 [15:8] of audio group B channel status for channels 3 and 4. R 0 275h ACSR3_4B_BYTE 10_11 ACSR3_4B_10 15-0 Bytes 10 [7:0] and 11 [15:8] of audio group B channel status for channels 3 and 4. R 0 276h ACSR3_4B_BYTE 12_13 ACSR3_4B_12 15-0 Bytes 12 [7:0] and 13 [15:8] of audio group B channel status for channels 3 and 4. R 0 277h ACSR3_4B_BYTE 14_15 ACSR3_4B_14 15-0 Bytes 14 [7:0] and 15 [15:8] of audio group B channel status for channels 3 and 4. R 0 278h ACSR3_4B_BYTE 16_17 ACSR3_4B_16 15-0 Bytes 16 [7:0] and 17 [15:8] of audio group B channel status for channels 3 and 4. R 0 279h ACSR3_4B_BYTE 18_19 ACSR3_4B_18 15-0 Bytes 18 [7:0] and 19 [15:8] of audio group B channel status for channels 3 and 4. R 0 27Ah ACSR3_4B_BYTE 20_21 ACSR3_4B_20 15-0 Bytes 20 [7:0] and 21 [15:8] of audio group B channel status for channels 3 and 4. R 0 27Bh ACSR3_4B_BYTE 22 RSVD 15-8 Reserved. R/W 0 ACSR3_4B_22 7-0 Bytes 22 of audio group B channel status for channels 3 and 4. R 0 RSVD 15-0 Reserved. R/W 0 27Ch 27Fh RSVD GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 133 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 280h ACSR_BYTE_0 281h 282h 283h 284h 285h 286h ACSR_BYTE_1 ACSR_BYTE_2 ACSR_BYTE_3 ACSR_BYTE_4 ACSR_BYTE_5 ACSR_BYTE_6 Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 ACSR0 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR1 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR2 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR3 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR4 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR5 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR6 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 134 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 287h ACSR_BYTE_7 288h 289h 28Ah 28Bh 28Ch 28Dh ACSR_BYTE_8 ACSR_BYTE_9 ACSR_BYTE_10 ACSR_BYTE_11 ACSR_BYTE_12 ACSR_BYTE_13 Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 ACSR7 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR8 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR9 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR10 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR11 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR12 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR13 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 135 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 28Eh ACSR_BYTE_14 28Fh 290h 291h 292h 293h 294h ACSR_BYTE_15 ACSR_BYTE_16 ACSR_BYTE_17 ACSR_BYTE_18 ACSR_BYTE_19 ACSR_BYTE_20 Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 ACSR14 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR15 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR16 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR17 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR18 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR19 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR20 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 136 of 145 Table 4-31: HD and 3G Audio Core Configuration and Status Registers (Continued) Address Register Name 295h ACSR_BYTE_21 296h 297h ACSR_BYTE_22 RSVD Bit Name Bit Description R/W Default RSVD 15-8 Reserved. R/W 0 ACSR21 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-8 Reserved. R/W 0 ACSR22 7-0 Audio channel status to use when ACS_REGEN is set or when adding audio channel status to non-AES/EBU audio. 8 bits per register starting at register 280h and ending at register 296h. W 0 RSVD 15-0 Reserved. R 29 Table 4-32: ANC Extraction FIFO Access Registers Address Register Name Bit Description R/W Default 800h BFFh ANC_PACKET_BANK 15-0 Extracted Ancillary Data 91024 words. Bit 15-8: Most Significant Word (MSW). Bit 7-0: Least Significant Word (LSW). See Section 4.18.8. R 0 Legend: R = Read only ROCW = Read Only, Clear on Write R/W = Read or Write W = Write only 4.22 JTAG Test Operation When the JTAG/HOST pin of the GS2970 is set HIGH, the host interface port is configured for JTAG test operation. In this mode, pins E7, F8, F7, and E8 become TDO, TCK, TMS, and TDI. In addition, the RESET_TRST pin operates as the test reset pin. Boundary scan testing using the JTAG interface is enabled in this mode. There are two ways in which JTAG can be used: 1. As a stand-alone JTAG interface to be used at in-circuit ATE (Automatic Test Equipment) during PCB assembly. 2. Under control of a host processor for applications such as system power on self tests. When the JTAG tests are applied by ATE, care must be taken to disable any other devices driving the digital I/O pins. If the tests are to be applied only at ATE, this can be GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 137 of 145 accomplished with tri-state buffers used in conjunction with the JTAG/HOST input signal. This is shown in Figure 4-51. GS2970 Application HOST CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO JTAG_HOST In-circuit ATE probe Figure 4-51: In-Circuit JTAG Alternatively, if the test capabilities are to be used in the system, the host processor may still control the JTAG/HOST input signal, but some means for tri-stating the host must exist in order to use the interface at ATE. This is represented in Figure 4-52. Application HOST GS2970 CS_TMS SCLK_TCK SDIN_TDI SDOUT_TDO JTAG_HOST Tri-State In-circuit ATE probe Figure 4-52: System JTAG Scan coverage is limited to digital pins only. There is no scan coverage for analog pins VCO, SDO/SDO, RSET, LF, and CP_RES. The JTAG/HOST pin must be held LOW during scan and therefore has no scan coverage. Please contact your Semtech representative to obtain the BSDL model for the GS2970. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 138 of 145 4.23 Device Power-up Because the GS2970 is designed to operate in a multi-voltage environment, any power-up sequence is allowed. The charge pump, phase detector, core logic, serial digital output and I/O buffers can all be powered up in any order. 4.24 Device Reset NOTE: At power-up, the device must be reset to operate correctly. In order to initialize all internal operating conditions to their default states, hold the RESET_TRST signal LOW for a minimum of treset = 10ms after all power supplies are stable. There are no requirements for power supply sequencing. When held in reset, all device outputs are driven to a high-impedance state. Nominal Level 95% of Nominal Level Supply Voltage treset treset Reset Reset RESET_TRST Figure 4-53: Reset Pulse 4.25 Standby Mode The STANDBY pin reduces power to a minimum by disabling all circuits except for the register configuration. Upon removal of the signal to the STANDBY pin, the device returns to its previous operating condition within 1 second, without requiring input from the host interface. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 139 of 145 5. Application Reference Design 5.1 Typical Application Circuit Power Filtering Power Decoupling +1.2V +3.3V EQ_VCC +1.2V_A 10n 10n 10n 10n 10n 10n +1.2V +1.2V_A 0R 10n 0R 1u 1u 10n 10n 1u 1u A_GND A_GND IO_VDD +3.3V_A 10n 10n 10n A_GND IO_VDD CD_VDD 0R 10n 10n 10n 10n 10n 10n 1u 1u 10n 1u 10n Place close to GS2970 A_GND +1.2V_A A_GND +3.3V_A 0R Place close to GS2970 R7 105R 10n 1u C18 33u 1u 10n 0R A_GND 22R 22R 22R A8 22R DOUT 19 DOUT 18 DOUT 17 DOUT 16 DOUT 15 DOUT 14 DOUT 13 DOUT 12 DOUT 11 DOUT 10 B8 A9 A10 B9 B10 C9 C10 C8 E10 E9 22R 22R 22R 22R 22R 22R 22R 22R 22R 22R DOUT 9 DOUT 8 DOUT 7 DOUT 6 DOUT 5 DOUT 4 DOUT 3 DOUT 2 DOUT 1 DOUT 0 F10 F9 H10 H9 J10 J9 K10 K9 J8 K8 22R 22R 22R 22R 22R 22R 22R 22R 22R 22R PCLK 47n DOUT[19:0] B3 RSV H6 XTAL_OUT J6 XTAL2 K6 XTAL1 G7 G8 H5 D7 H3 H8 H7 G3 D8 K2 C7 J2 SMPTE_BY PASS DVB_ASI TIM_861 SW_EN AUDIO_EN/DIS IOPROC_EN/DIS 20BIT/10BIT RC_BY P JTAG/HOST STANDBY RESET_TRST SDO_EN/DIS E7 E8 F8 F7 SDOUT_TDO SDIN_TDI SCLK_TCK CS_TMS A_GND TP 16p SMPTE_BY PASS DVB_ASI TIM_861 SW_EN AUDIO_EN/DIS IOPROC_EN/DIS 20BIT/10BIT RC_BY P JTAG/HOST STANDBY RESET_TRST SDO_EN/DIS EQ_VCC RSV F2 G1 G2 RSV RSV RSV B6 C5 C6 AMCLK ACLK WCLK K4 J4 H4 AOUT_1/2 AOUT_3/4 J3 K3 AOUT_5/6 AOUT_7/8 J5 K5 LOCKED (DEFAULT, PROGRAMMABLE) Y /1ANC (DEFAULT, PROGRAMMABLE) DATA_ERRORb (DEFAULT, PROGRAMMABLE) 22R 22R 22R AUDIO MASTER CLOCK AUDIO SERIAL BIT CLOCK AUDIO WORD CLOCK AUDIO OUTPUT CH 1 & 2 AUDIO OUTPUT CH 3 & 4 AUDIO OUTPUT CH 5 & 6 AUDIO OUTPUT CH 7 & 8 A_GND A_GND VEE SD/HD VCC 10 A_GND A_GND 10n 75R UCBBJE20-1 5n6 9 1 4u7 75R CD SLEW RATE SELECT CD_VDD CD_DISABLEb 10n A_GND A_GND A_GND 75R TAB RSET 750R 12 11 2 3 14 13 NC 15 GS2978-CNE3 SDO 5 CD_VDD SDO SDI NC 4 A_GND 75R CD_VDD 17 3 SDI RSVD 2 NC 16 1 NC NC 49R9 8 10n A_GND IO_GND IO_GND IO_GND IO_GND B7 D9 G9 J7 D5 E5 F5 G5 A_GND 470n J1 49R9 10n H2 E2 Close to pin C1 & D1 of GS2970 TERM C2 D2 D3 E3 F3 A_GND F1 VCO_GND PLL_GND PLL_GND PLL_GND 9 K1 7 SDO DISABLE SDO SDI CORE_GND CORE_GND CORE_GND CORE_GND SDI BUF_GND SDI_GND D1 A_GND A_GND A_GND A_GND A_GND C1 10 4u7 NC 13 VCC MCLAD BYPASS 10n 470n 11 B4 D4 E4 F4 A_GND VEE 17 37R4 75-ohm Traces Close to pin 1 & 2 of GS2978 A_GND TAB MUTE 14 15 CD VCC VEE SDO 12 8 75R 4 SDO SDIN AGC 1u VEE GS2984/ GS2974 SDIN AGC 3 7 2 75R VEE 5 3 2 SDI Input 1 1u 6 A_GND 1 A_GND G4 STAT3 STAT4 STAT5 10n 16 10n UCBBJE20-1 GS2970-IBE3 CD_DISABLEb SDOUT_TDO SDIN_TDI SCLK_TCK CS_TMS EQ_VCC 6n2 CS10-27.000M 6 Host Interface & Control 16p PCLK DOUT[19:0] LF Audio Data and Clock Output A2 F/DE (DEFAULT, PROGRAMMABLE) V/VSY NC (DEFAULT, PROGRAMMABLE) H/HSY NC (DEFAULT, PROGRAMMABLE) Video Data, Clock & Timing Output A7 D10 G10 K7 H1 D6 E6 F6 G6 B1 A_VDD IO_VDD IO_VDD IO_VDD IO_VDD B5 A6 A5 STAT2 STAT1 STAT0 1u A_GND SDI Loop-Through Output VBG BUF_VDD LB_CONT A1 IO_VDD +1.2V CORE_VDD CORE_VDD CORE_VDD CORE_VDD A3 SDI_VDD R19 DNP B2 C3 C4 A4 VCO_VDD +3.3V_A DNP PLL_VDD PLL_VDD PLL_VDD Place close to GS2970 +3.3V_A E1 +1.2V_A A_GND Notes: 1. DNP (Do Not Populate). 2. The value of the series resistors on video data, clock, and timing connections should be determined by board signal integrity test. 3. For analog power and ground isolation refer to PCB layout guide. 4. For critital 3G signal layout refer to PCB layout guide. 5. For impedance controlled signal layout refer to PCB layout guide. GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 140 of 145 6. References & Relevant Standards SMPTE 125M Component video signal 4:2:2 - bit parallel interface SMPTE 259M 10-bit 4:2:2 Component and 4fsc Composite Digital Signals - Serial Digital Interface SMPTE 260M 1125 / 60 high definition production system - digital representation and bit parallel interface SMPTE 267M Bit parallel digital interface - component video signal 4:2:2 16 x 9 aspect ratio SMPTE 272M Formatting AES/EBU Audio and Auxiliary Data into Digital Video Ancillary Data Space SMPTE 274M 1920 x 1080 scanning analog and parallel digital interfaces for multiple picture rates SMPTE 291M Ancillary Data Packet and Space Formatting SMPTE 292 Bit-Serial Digital Interface for High-Definition Television Systems SMPTE 293M 720 x 483 active line at 59.94Hz progressive scan production - digital representation SMPTE 296M 1280 x 720 scanning, analog and digital representation and analog interface SMPTE 299M 24-Bit Digital Audio Format for HDTV Bit-Serial Interface SMPTE 352M Video Payload Identification for Digital Television Interfaces SMPTE 424M Television - 3Gb/s Signal/Data Serial Interface SMPTE 425M Television - 3Gb/s Signal/Data Serial Interface - Source Image Format Mapping SMPTE RP165 Error Detection Checkwords and Status Flags for Use in Bit-Serial Digital Interfaces for Television SMPTE RP168 Definition of Vertical Interval Switching Point for Synchronous Video Switching GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 141 of 145 7. Package & Ordering Information 7.1 Package Dimensions 1.700 (0.366) 0.366 GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 142 of 145 7.2 Packaging Data Table 7-1: Packaging Data Parameter Value Package Type 11mm x 11mm 100-ball LBGA Package Drawing Reference JEDEC M0192 (with exceptions noted in Package Dimensions on page 142). Moisture Sensitivity Level 3 Junction to Case Thermal Resistance, j-c 15.4C/W Junction to Air Thermal Resistance, j-a (at zero airflow) 37.1C/W Junction to Board Thermal Resistance, j-b 26.4C/W Psi, 0.4C/W Pb-free and RoHS Compliant Yes 7.3 Marking Diagram Pin 1 Indicator GS2970 XXXXXXE3 YYWW XXXXXX - Last 6 digits (excluding decimal) of SAP Batch Assembly (FIN) as listed on Packing Slip E3 - Pb-free & Green indicator YYWW - Date Code GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 143 of 145 7.4 Solder Reflow Profiles The GS2970 is available in a Pb-free package. It is recommended that the Pb-free package be soldered with Pb-free paste using the reflow profile shown in Figure 7-1. Temperature 60-150 sec. 20-40 sec. 260C 250C 3C/sec max 217C 6C/sec max 200C 150C 25C Time 60-180 sec. max 8 min. max Figure 7-1: Pb-free Solder reflow Profile 7.5 Ordering Information Part Number Package Pb-free Temperature Range GS2970-IBE3 100-ball BGA Yes -20C to 85C GS2970 3Gb/s, HD, SD SDI Receiver Complete with SMPTE Audio and Video Processing Data Sheet 47478 - 4 September 2012 144 of 145 DOCUMENT IDENTIFICATION CAUTION DATA SHEET ELECTROSTATIC SENSITIVE DEVICES Information relating to this product and the application or design described herein is believed to be reliable, however such information is provided as a guide only and Semtech assumes no liability for any errors in this document, or for the application or design described herein. Semtech reserves the right to make changes to the product or this document at any time without notice. DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION (c) Semtech 2012 All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified range. SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER'S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Contact Information Semtech Corporation Gennum Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111, Fax: (805) 498-3804 www.semtech.com GS2970 3Gb/s, HD, SD SDI Receiver Data Sheet 47478 - 4 September 2012 145 of 145 145 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Semtech: GS2970-IBE3 GS2970-CBE3