General Description
The MAX5065/MAX5067 dual-phase, PWM controllers
provide high-output-current capability in a compact
package with a minimum number of external compo-
nents. The MAX5065/MAX5067 utilize a dual-phase,
average-current-mode control that enables optimal use
of low RDS(ON) MOSFETs, eliminating the need for exter-
nal heatsinks even when delivering high output currents.
Differential sensing enables accurate control of the out-
put voltage, while adaptive voltage positioning provides
optimum transient response. An internal regulator
enables operation with input voltage ranges of +4.75V to
+5.5V or +8V to +28V. The high switching frequency, up
to 500kHz per phase, and dual-phase operation allow
the use of low-output inductor values and input capacitor
values. This accommodates the use of PC board-
embedded planar magnetics achieving superior reliabili-
ty, current sharing, thermal management, compact size,
and low system cost.
The MAX5065/MAX5067 also feature a clock input
(CLKIN) for synchronization to an external clock, and a
clock output (CLKOUT) with programmable phase delay
(relative to CLKIN) for paralleling multiple phases. The
MAX5065/MAX5067 also limit the reverse current if the
bus voltage becomes higher than the regulated output
voltage. These devices are specifically designed to limit
current sinking when multiple power-supply modules are
paralleled. The MAX5065 offers an adjustable +0.6V to
+3.3V output voltage. The MAX5067 output voltage is
adjustable from +0.8V to +3.3V and features an overvolt-
age protection and a power-good output signal.
The MAX5065/MAX5067 operate over the extended
temperature range (-40°C to +85°C). The MAX5065 is
available in a 28-pin SSOP package. The MAX5067 is
available in a 44-pin thin QFN package. Refer to the
MAX5037A data sheet for a VRM 9.0/VRM 9.1-compati-
ble, VID-controlled output voltage controller in a 44-pin
QFN package.
Applications
Servers and Workstations
Point-of-Load High-Current/High-Density
Telecom DC-DC Regulators
Networking Systems
Large-Memory Arrays
RAID Systems
High-End Desktop Computers
Features
+4.75V to +5.5V or +8V to +28V Input Voltage
Range
Adjustable VOUT
+0.6V to +3.3V (MAX5065)
+0.8V to +3.3V (MAX5067)
Up to 60A Output Current
Internal Voltage Regulator for a +12V or +24V
Power Bus
Programmable Adaptive Output Voltage
Positioning
True Differential Remote Output Sensing
Out-of-Phase Controllers Reduce Input
Capacitance Requirement and Distribute Power
Dissipation
Average-Current-Mode Control
Superior Current Sharing Between Individual
Phases and Paralleled Modules
Accurate Current Limit Eliminates MOSFET and
Inductor Derating
Limits Reverse-Current Sinking in Paralleled
Modules
Integrated 4A Gate Drivers
Selectable Fixed Frequency 250kHz or 500kHz Per
Phase (Up to 1MHz for Two Phases)
External Frequency Synchronization from 125kHz
to 600kHz
Internal PLL with Clock Output for Paralleling
Multiple DC-DC Converters
Thermal Protection
28-Pin SSOP Package (MAX5065)
44-Pin Thin QFN Package (MAX5067)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
________________________________________________________________Maxim Integrated Products 1
19-3035; Rev 1; 11/03
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Ordering Information
PART TEMP RANGE PIN-PACKAGE
MAX5065EAI -40°C to +85°C 28 SSOP
MAX5067ETH -40°C to +85°C 44 Thin QFN
Selector Guide and Pin Configurations appear at end of
data sheet.
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VCC = +5V, circuit of Figure 1, TA= -40°C to +85°C, unless otherwise noted. Typical specifications are at TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
IN to SGND.............................................................-0.3V to +30V
BST_ to SGND ........................................................-0.3V to +35V
DH_ to LX_ .................................-0.3V to [(VBST_ - VLX_) + 0.3V]
DL_ to PGND..............................................-0.3V to (VCC + 0.3V)
BST_ to LX_ ..............................................................-0.3V to +6V
VCC to SGND............................................................-0.3V to +6V
VCC, VDD to PGND ...................................................-0.3V to +6V
SGND to PGND .....................................................-0.3V to +0.3V
All Other Pins to SGND...............................-0.3V to (VCC + 0.3V)
Continuous Power Dissipation (TA= +70°C)
28-Pin SSOP (derate 9.5mW/°C above +70°C) ............762mW
44-Pin Thin QFN (derate 27.0mW/°C above+70°C) ...2162mW
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
SYSTEM SPECIFICATIONS
828
Input Voltage Range VIN Short IN and VCC together for +5V input
operation 4.75 5.50 V
Quiescent Supply Current IQEN = VCC or SGND 4 10 mA
Efficiency ηILOAD = 52A (26A per phase) 90 %
OUTPUT VOLTAGE
No load 0.5952 0.6 0.6048
MAX5065 No load, VCC = +4.75V to +5.5V
or VIN = +8V to +28V 0.594 0.6 0.6064
No load 0.7936 0.8 0.8064
SENSE+ to SENSE- Accuracy
(Note 4)
MAX5067 No load, VCC = +4.75V to +5.5V
or VIN = +8V to +28V 0.792 0.8 0.808
V
STARTUP/INTERNAL REGULATOR
VCC Undervoltage Lockout UVLO VCC rising 4.0 4.15 4.5 V
VCC Undervoltage Lockout
Hysteresis 200 mV
VCC Output Accuracy VIN = +8V to +28V, ISOURCE = 0 to 80mA 4.85 5.1 5.30 V
MOSFET DRIVERS
Output Driver Impedance RON Low or high output 1 3
Output Driver Source/Sink
Current IDH_, IDL_4A
Nonoverlap Time tNO CDH_/DL_ = 5nF 60 ns
OSCILLATOR AND PLL
CLKIN = SGND 238 250 262
Switching Frequency fSW CLKIN = VCC 475 500 525 kHz
PLL Lock Range fPLL 125 600 kHz
PLL Locking Time tPLL 200 µs
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(VCC = +5V, circuit of Figure 1, TA= -40°C to +85°C, unless otherwise noted. Typical specifications are at TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
PHASE = VCC 115 120 125
PHASE = unconnected 85 90 95
CLKOUT Phase Shift
(At fSW = 125kHz) φCLKOUT
PHASE = SGND 55 60 65
degrees
CLKIN Input Pulldown Current ICLKIN 357µA
CLKIN High Threshold VCLKINH 2.4 V
CLKIN Low Threshold VCLKINL 0.8 V
CLKIN High Pulse Width tCLKIN 200 ns
PHASE High Threshold VPHASEH 4V
PHASE Low Threshold VPHASEL 1V
PHASE Input Bias Current IPHASEBIAS -50 +50 µA
CLKOUT Output Low Level VCLKOUTL ISINK = 2mA (Note 2) 100 mV
CLKOUT Output High Level VCLKOUTH ISOURCE = 2mA (Note 2) 4.5 V
CURRENT LIMIT
Average Current-Limit Threshold VCL CSP_ to CSN_ 45 48 51 mV
Reverse Current-Limit Threshold VCLR CSP_ to CSN_ -3.9 -0.2 mV
Cycle-by-Cycle Current Limit VCLPK CSP_ to CSN_ (Note 3) 90 112 130 mV
Cycle-by-Cycle Overload
Response Time tRVCSP_ to VCSN_ = +150mV 260 ns
CURRENT-SENSE AMPLIFIER
CSP_ to CSN_ Input Resistance RCS_4k
Common-Mode Range VCMR
(
CS
)
-0.3 +3.6 V
Input Offset Voltage VOS
(
CS
)
-1 +1 mV
Amplifier Gain AV(CS) 18 V/V
3dB Bandwidth f3dB 4 MHz
CURRENT-ERROR AMPLIFIER (TRANSCONDUCTANCE AMPLIFIER)
Transconductance gmca 550 µS
Open-Loop Gain AVOL
(
CE
)
No load 50 dB
DIFFERENTIAL VOLTAGE AMPLIFIER (DIFF)
Common-Mode Voltage Range VCMR
(
DIFF
)
-0.3 +1.0 V
DIFF Output Voltage VCM VSENSE+ = VSENSE- = 0 0.6 V
Input Offset Voltage VOS
(
DIFF
)
-1 +1 mV
Amplifier Gain AV
(
DIFF
)
0.997 1 1.003 V/V
3dB Bandwidth f3dB CDIFF = 20pF 3 MHz
Minimum Output Current Drive IOUT
(
DIFF
)
1.0 mA
SENSE+ to SENSE- Input
Resistance RVS_ 50 100 k
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(VCC = +5V, circuit of Figure 1, TA= -40°C to +85°C, unless otherwise noted. Typical specifications are at TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
VOLTAGE-ERROR AMPLIFIER (EAOUT)
Open-Loop Gain AVOL
(
EA
)
70 dB
Unity-Gain Bandwidth fUGEA 3 MHz
EAN Input Bias Current IB(EA) VEAN = +2.0V -100 +100 nA
Error-Amplifier Output Clamping
Voltage VCLAMP
(
EA
)
With respect to VCM 810 918 mV
POWER-GOOD, PHASE FAILURE DETECTION, OVERVOLTAGE PROTECTION, AND THERMAL SHUTDOWN
VOV PGOOD goes low when VOUT is outside this
window +6 +8 +10
PGOOD Trip Level (MAX5067)
VUV PGOOD goes low when VOUT is outside this
window -12.5 -10 -8.5
%VOUT
PGOOD Output Low Level
(MAX5067) VPGLO ISINK = 4mA 0.2 V
PGOOD Output Leakage Current
(MAX5067) IPG PGOOD = VCC A
Phase Failure Trip Threshold
(MAX5067) VPH PGOOD goes low when CLP_ is higher
than VPH 2V
OVPIN Trip Threshold (MAX5067) OVPTH With respect to SGND 0.792 0.8 0.808 V
OVPIN Input Resistance
(MAX5067) ROVPIN 190 280 370 k
THERMAL SHUTDOWN
Thermal Shutdown TSHDN 150 °C
Thermal-Shutdown Hysteresis 8°C
EN INPUT
EN Input Low Voltage VENL 1V
EN Input High Voltage VENH 3V
EN Pullup Current IEN 4.5 5 5.5 µA
Note 1: Specifications from -40°C to 0°C are guaranteed by characterization but not production tested.
Note 2: Guaranteed by design. Not production tested.
Note 3: See Peak-Current Comparator section.
Note 4: Does not include an error due to finite error amplifier gain. See the Voltage-Error Amplifier section.
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
_______________________________________________________________________________________ 5
EFFICIENCY vs. OUTPUT CURRENT AND
INTERNAL OSCILLATOR FREQUENCY
MAX5065/67 toc01
IOUT (A)
η (%)
4844403632282420161284
50
60
70
80
90
100
40
052
f = 500kHz
f = 250kHz
VIN = +5V
VOUT = +1.8V
EFFICIENCY vs. OUTPUT CURRENT
AND INPUT VOLTAGE
MAX5065/67 toc02
IOUT (A)
η (%)
4844403632282420161284
50
40
30
20
10
60
70
80
90
100
0
052
VIN = +12V
VIN = +5V
VOUT = +1.8V
fSW = 250kHz
EFFICIENCY vs. OUTPUT CURRENT
AND INPUT VOLTAGE
MAX5065/67 toc03
OUTPUT CURRENT (A)
η (%)
484436 4012 16 20 24 28 324 8
10
20
30
40
50
60
70
80
90
100
0
052
VIN = +12V
VIN = +5V
VOUT = 1V
fSW = 250kHz
EFFICIENCY vs. OUTPUT CURRENT
MAX5065/67 toc04
IOUT (A)
η (%)
4844403632282420161284
50
40
30
20
10
60
70
80
90
100
0
052
VIN = +24V
VOUT = +1.8V
fSW = 125kHz
EFFICIENCY vs. OUTPUT CURRENT
AND OUTPUT VOLTAGE
MAX5065/67 toc05
OUTPUT CURRENT (A)
η (%)
4844403632282420161284
50
40
30
20
10
60
70
80
90
100
0
052
VOUT = +1V
VOUT = +1.5V
VOUT = +1.8V
VIN = +12V
fSW = 250kHz
EFFICIENCY vs. OUTPUT CURRENT
AND OUTPUT VOLTAGE
MAX5065/67 toc06
OUTPUT CURRENT (A)
η (%)
4844403632282420161284
50
40
30
20
10
60
70
80
90
100
0
052
VOUT = +1V
VOUT = +1.5V VOUT = +1.8V
VIN = +12V
fSW = 500kHz
SUPPLY CURRENT
vs. FREQUENCY AND INPUT VOLTAGE
MAX5065/67 toc07
FREQUENCY (kHz)
ICC (mA)
550500400 450200 250 300 350150
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
6.0
100 600
VIN = +24V
VIN = +12V
VIN = +5V EXTERNALCLOCK
NO DRIVER LOAD
SUPPLY CURRENT
vs. TEMPERATURE AND FREQUENCY
MAX5065/67 toc08
TEMPERATURE (°C)
ICC (mA)
603510-15
10
20
30
40
50
60
70
80
90
100
0
-40 85
250kHz
125kHz
VIN = +12V
CDL_ = 22nF
CDH_ = 8.2nF
SUPPLY CURRENT
vs. LOAD CAPACITANCE PER DRIVER
MAX5065/67 toc09
CDRIVER (nF)
ICC (mA)
13117 953
10
20
30
40
50
60
70
80
90
100
0
115
VIN = +12V
fSW = 250kHz
Typical Operating Characteristics
(Circuit of Figure 1. TA= +25°C, unless otherwise noted.)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
6 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(Circuit of Figure 1, TA= +25°C, unless otherwise noted.)
CURRENT-SENSE THRESHOLD
vs. OUTPUT VOLTAGE
MAX5065/67 toc10
VOUT (V)
(VCSP_ - VCSN_) (mV)
1.71.61.4 1.51.2 1.31.1
46
47
48
49
50
51
52
53
54
55
45
1.0 1.8
PHASE 2
PHASE 1
10
0.1
4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
OVERVOLTAGE THRESHOLD (PGOOD)
vs. INPUT VOLTAGE
1
MAX5065/67 toc11
VIN (V)
VOV (V)
VOUT = +0.8V
VOUT = +3.3V
10
4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
UNDERVOLTAGE THRESHOLD (PGOOD)
vs. INPUT VOLTAGE
1
0.1
MAX5065/67 toc12
VIN (V)
VUV (V)
VOUT = +0.8V
VOUT = +3.3V
1.50
1.60
1.55
1.75
1.70
1.65
1.80
1.85
1.90
08124 16202428323640444852
OUTPUT VOLTAGE vs. OUTPUT CURRENT
AND ERROR AMP GAIN (RF/RIN)
MAX5065/67 toc13
ILOAD (A)
VOUT (V)
RF/RIN = 40 RF/RIN = 20
RF/RIN = 7.5
RF/RIN = 10
DIFFERENTIAL AMPLIFIER BANDWIDTH
MAX5065/67 toc14
FREQUENCY (MHz)
GAIN (V/V)
PHASE (deg)
10.1
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
0.01 10
-225
-270
-180
-135
-90
-45
0
45
90
PHASE
GAIN
DIFF OUTPUT ERROR
vs. SENSE+ TO SENSE- VOLTAGE
MAX5065/67 toc15
VSENSE (V)
ERROR (%)
1.91.81.1 1.2 1.3 1.5 1.61.4 1.7
0.025
0.050
0.075
0.100
0.125
0.150
0.175
0.200
0
1.0 2.0
VIN = +12V
NO DRIVER
VCC LOAD REGULATION
vs. INPUT VOLTAGE
MAX5065/67 toc16
ICC (mA)
VCC (V)
13512015 30 45 75 9060 105
4.85
4.90
4.95
5.00
5.05
5.10
5.15
5.20
4.80
0 150
VIN = +24V
VIN = +12V
VIN = +8V
DC LOAD
VCC LINE REGULATION
MAX5065/67 toc18
VIN (V)
VCC (V)
131291011
4.80
4.85
4.90
4.95
5.00
5.05
5.10
5.15
5.20
5.25
4.75
8
ICC = 80mA
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
_______________________________________________________________________________________ 7
DRIVER RISE TIME
vs. DRIVER LOAD CAPACITANCE
MAX5065/67 toc19
CDRIVER (nF)
tR (ns)
312616 21116
10
20
30
40
50
60
70
80
90
100
110
120
0
136
DL_
DH_
VIN = +12V
fSW = 250kHz
DRIVER FALL TIME
vs. DRIVER LOAD CAPACITANCE
MAX5065/67 toc20
CDRIVER (nF)
tR (ns)
312616 21116
10
20
30
40
50
60
70
80
90
100
110
120
0
136
DL_
DH_
VIN = +12V
fSW = 250kHz
100ns/div
HIGH-SIDE DRIVER (DH_)
SINK AND SOURCE CURRENT
DH_
1.6A/div
MAX5065/67 toc21
VIN = +12V
CDH_ = 22nF
100ns/div
LOW-SIDE DRIVER (DL_)
SINK AND SOURCE CURRENT
DL_
1.6A/div
MAX5065/67 toc22
VIN = +12V
CDL_ = 22nF
100µs/div
PLL LOCKING TIME
250kHz TO 350kHz AND
350kHz TO 250kHz
CLKOUT
5V/div
MAX5065/67 toc23
PLLCMP
200mV/div
VIN = +12V
NO LOAD
350kHz
250kHz
0
100µs/div
PLL LOCKING TIME
250kHz TO 500kHz AND
500kHz TO 250kHz
CLKOUT
5V/div
MAX5065/67 toc24
PLLCMP
200mV/div
0
VIN = +12V
NO LOAD
500kHz
250kHz
100µs/div
PLL LOCKING TIME
250kHz TO 150kHz AND
150kHz TO 250kHz
CLKOUT
5V/div
MAX5065/67 toc25
PLLCMP
200mV/div
0
VIN = +12V
NO LOAD
250kHz
150kHz
Typical Operating Characteristics (continued)
(Circuit of Figure 1, TA= +25°C, unless otherwise noted.)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
8 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(Circuit of Figure 1, TA= +25°C, unless otherwise noted.)
40ns/div
LOW-SIDE DRIVER (DL_)
RISE TIME
MAX5065/67 toc28
DL_
2V/div
VIN = +12V
CDL_ = 22nF
40ns/div
LOW-SIDE DRIVER (DL_)
FALL TIME
MAX5065/67 toc29
DL_
2V/div
VIN = +12V
CDL_ = 22nF
500ns/div
OUTPUT RIPPLE
MAX5065/67 toc30
VOUT
(AC-COUPLED)
10mV/div
VIN = +12V
VOUT = +1.75V
IOUT = 52A
2ms/div
INPUT STARTUP RESPONSE
MAX5065/67 toc31
VIN
5V/div
VIN = +12V
VOUT = +1.75V
IOUT = 52A
VPGOOD
1V/div
VOUT
1V/div
40ns/div
HIGH-SIDE DRIVER (DH_)
RISE TIME
MAX5065/67 toc26
VIN = +12V
CDH_ = 22nF
DH_
2V/div
40ns/div
HIGH-SIDE DRIVER (DH_)
FALL TIME
MAX5065/67 toc27
DH_
2V/div
VIN = +12V
CDH_ = 22nF
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
_______________________________________________________________________________________ 9
1ms/div
ENABLE STARTUP RESPONSE
MAX5065/67 toc32
VEN
2V/div
VPGOOD
1V/div
VOUT
1V/div
VIN = +12V
VOUT = +1.75V
IOUT = 52A
40µs/div
LOAD-TRANSIENT RESPONSE
MAX5065/67 toc33
VIN = +12V
VOUT = +1.75V
ISTEP = 8A TO 52A
tRISE = 1µs
VOUT
50mV/div
REVERSE CURRENT SINK
vs. TEMPERATURE
MAX5065/67 toc34
TEMPERATURE (°C)
IREVERSE (A)
603510-15
2.4
2.5
2.6
2.7
2.8
2.3
-40 85
VEXTERNAL = +3.3V
VEXTERNAL = +2V
VIN = +12V
VOUT = 1.5V R1 = R2 = 1.5m
200µs/div
REVERSE CURRENT SINK AT INPUT TURN-ON
(VIN = 12V, VOUT = 1.5V, VEXTERNAL = 2.5V)
MAX5065/67 toc35
REVERSE
CURRENT
5A/div
0A
R1 = R2 = 1.5m
200µs/div
REVERSE CURRENT SINK AT INPUT TURN-ON
(VIN = 12V, VOUT = 1.5V, VEXTERNAL = 3.3V)
MAX5065/67 toc36
REVERSE
CURRENT
10A/div
0A
R1 = R2 = 1.5m
200µs/div
REVERSE CURRENT SINK AT ENABLE TURN-ON
(VIN = 12V, VOUT = 1.5V, VEXTERNAL = 2.5V)
MAX5065/67 toc37
REVERSE
CURRENT
5A/div
0A
R1 = R2 = 1.5m
200µs/div
REVERSE CURRENT SINK AT ENABLE TURN-ON
(VIN = 12V, VOUT = 1.5V, VEXTERNAL = 3.3V)
MAX5065/67 toc38
REVERSE
CURRENT
10A/div
0A
R1 = R2 = 1.5m
Typical Operating Characteristics (continued)
(Circuit of Figure 1, TA= +25°C, unless otherwise noted.)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
10 ______________________________________________________________________________________
Pin Description
PIN
MAX5065 MAX5067 NAME FUNCTION
1, 13 39, 16 CSP2,
CSP1
Current-Sense Differential Amplifier Positive Inputs. Sense the inductor current. The differential
voltage between CSP_ and CSN_ is amplified internally by the current-sense amplifier gain of
18.
2, 14 40, 17 CSN2,
CSN1
Current-Sense Differential Amplifier Negative Inputs. Together with CSP_, sense the inductor
current.
3 41 PHASE
Phase-Shift Setting Input. Connect PHASE to VCC for 120°, leave PHASE unconnected for 90°,
or connect PHASE to SGND for 60° of phase shift between the rising edge of CLKOUT and
CLKIN/DH1.
4 42 PLLCMP External Loop-Compensation Input. Connect compensation network for the phase-locked loop
(see the Phase-Locked Loop section).
5, 7 43, 7 CLP2,
CLP1
Current-Error Amplifier Outputs. Compensate the current loop by connecting an RC network to
ground.
6 5, 20, 35 SGND Signal Ground. Ground connection for the internal control circuitry.
8 10 SENSE+
Differential Output-Voltage-Sensing Positive Input. Used to sense a remote load. The MAX5065
and MAX5067 regulate the difference between SENSE+ and SENSE- according to the factory
preset reference voltage of +0.6V and +0.8V, respectively.
9 11 SENSE- Differential Output Voltage-Sensing Negative Input. Used to sense a remote load. Connect
SENSE- to VOUT- or PGND at the load.
10 12 DIFF Differential Remote-Sense Amplifier Output. DIFF is the output of a precision unity-gain
amplifier.
11 13 EAN Voltage-Error Amplifier Inverting Input. Receives a signal from the output of the differential
remote-sense amplifier. Referenced to SGND.
12 14 EAOUT
Voltage-Error Amplifier Output. Connect to the external gain-setting feedback resistor. The
external error amplifier gain-setting resistors determine the amount of adaptive voltage
positioning.
15 19 EN Output Enable. A logic-low shuts down the power drivers. EN has an internal 5µA pullup
current.
16, 26 22, 34 BST1,
BST2
Boost Flying-Capacitor Connection. Reservoir capacitor connection for the high-side FET driver
supply. Connect a 0.47µF ceramic capacitor between BST_ and LX_.
17, 25 23, 32 DH1,
DH2 High-Side Gate-Driver Outputs. Drive the gate of the high-side MOSFET.
18, 24 24, 31 LX1, LX2 Inductor Connection. Source connection for the high-side MOSFETs. Also serve as the return
terminal for the high-side driver.
19, 23 25, 30 DL1, DL2 Low-Side Gate-Driver Outputs. Synchronous MOSFET gate drivers for the two phases.
20 27 VCC Internal +5V Regulator Output. VCC is derived internally from the IN voltage. Bypass to SGND
with 4.7µF and 0.1µF ceramic capacitors in parallel.
21 28 IN
Supply Voltage Connection. Connect IN to VCC for a +5V system. Connect the unregulated
power source to IN through an RC lowpass filter comprised of a 2.2 resistor and a 0.1µF
ceramic capacitor.
22 29 PGND Power Ground. Connect the VCC bypass capacitors, input capacitors, output capacitors, and
low-side synchronous MOSFET source to PGND.
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 11
Detailed Description
The MAX5065/MAX5067 average-current-mode PWM
controllers drive two out-of-phase buck converter chan-
nels. Average-current-mode control improves current
sharing between the channels while minimizing compo-
nent derating and size. Parallel multiple MAX5065/
MAX5067 regulators to increase the output current
capacity. For maximum ripple rejection at the input, set
the phase shift between phases to 90°for two paral-
leled converters, or 60°for three paralleled converters.
Paralleling the MAX5065/MAX5067s improves design
flexibility in applications requiring upgrades (higher
load).
Dual-phase converters with an out-of-phase locking
arrangement reduce the input and output capacitor
ripple current, effectively multiplying the switching fre-
quency by the number of phases. Each phase of the
MAX5065/MAX5067 consists of an inner average cur-
rent loop controlled by a common outer-loop voltage-
error amplifier (VEA). The combined action of the two
inner current loops and the outer voltage loop corrects
the output voltage errors and forces the phase currents
to be equal. Program the output voltage from +0.6V to
+3.3V (MAX5065) and +0.8V to +3.3V (MAX5067) using
a resistive-divider at SENSE+ and SENSE-.
VIN, VCC, VDD
The MAX5065/MAX5067 accept a wide input voltage
range of +4.75V to +5.5V or +8V to +28V. All internal
control circuitry operates from an internally regulated
nominal voltage of +5V (VCC). For input voltages of +8V
or greater, the internal VCC regulator steps the voltage
down to +5V. The VCC output voltage regulates to +5V
while sourcing up to 80mA. Bypass VCC to SGND with
4.7µF and 0.1µF low-ESR ceramic capacitors for high-
frequency noise rejection and stable operation (Figures
1, 2, and 3).
Calculate power dissipation in the MAX5065/MAX5067
as a product of the input voltage and the total VCC reg-
ulator output current (ICC). ICC includes quiescent cur-
rent (IQ) and gate-drive current (IDD):
PD = VIN x ICC
ICC = IQ+ fSW x (QG1 + QG2 + QG3 + QG4)
Pin Description (continued)
PIN
MAX5065 MAX5067 NAME FUNCTION
27 36 CLKOUT Oscillator Output. CLKOUT is phase-shifted from CLKIN by the amount determined by the
PHASE input. Use CLKOUT to parallel additional MAX5065/MAX5067s.
28 38 CLKIN
CMOS Logic Clock Input. Drive CLKIN with a frequency range between 125kHz and 600kHz or
connect to VCC or SGND. Connect CLKIN to SGND to set the internal oscillator to 250kHz or
connect to VCC to set the internal oscillator to 500kHz. CLKIN has an internal 5µA pulldown
current.
6 OVPIN
Overvoltage Protection Circuit Input. Connect OVPIN to the center of the resistive-divider
between VOUT and GND. When OVPIN exceeds +0.8V with respect to SGND, OVPOUT latches
DH_ low and DL_ high. Toggle EN low to high or recycle the power to reset the latch.
8 OVPOUT Overvoltage Protection Output. Use the OVPOUT active-high, push-pull output to trigger a
safety device such as an SCR.
9 PGOOD
Power-Good Output. The open-drain, active-low PGOOD output goes low when the output
voltage falls out of regulation or a phase failure is detected. The power-good window-
comparator thresholds are +8% and -10% of the output voltage. Forcing EN low also forces
PGOOD low.
1, 2, 3, 4,
15, 18,
21, 33,
37, 44
N.C. No Connection. Not internally connected.
26 VDD
Supply Voltage for Low-Side and High-Side Drivers. VCC powers VDD. Connect a parallel
combination of 0.1µF and 1µF ceramic capacitors to PGND and a 1 resistor to VCC to filter
out the high peak currents of the driver from the internal circuitry.
(1)
(2)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
12 ______________________________________________________________________________________
MAX5065
IN
EN
PHASE 1
CSP1
DRV_VCC
RAMP1
GMIN
CLK
CLP1
CSN1
SHDN BST1
DL1
LX1
DH1
VCC
TO INTERNAL CIRCUITS
TO INTERNAL CIRCUITS
CSP1
CSN1
CLP1
PHASE 2
CSP2
DRV_VCC
GMIN
CLK
CLP2
CSN2
SHDN
BST2
DL2
LX2
DH2
CSP2
CSN2
CLP2
PHASE-
LOCKED
LOOP
RAMP
GENERATOR
RAMP2
CLKIN
PHASE
CLKOUT
PLLCMP
DIFF
AMP
ERROR
AMP
SENSE-
SENSE+
DIFF
EAN
EAOUT
PGND
PGND
PGND
SGND
VREF = 0.6V + VCM
+5V
LDO
REGULATOR
UVLO
POR
TEMP SENSOR
0.6V
Functional Diagrams
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 13
MAX5067
IN
EN
PHASE 1
CSP1
DRV_VCC
RAMP1
GMIN
CLK
CLP1
CSN1
SHDN BST1
DL1
LX1
DH1
VCC
VDD TO INTERNAL CIRCUITS
CSP1
CSN1
CLP1
PHASE 2
CSP2
DRV_VCC
GMIN
CLK
CLP2
CSN2
SHDN
BST2
DL2
LX2
DH2
OVPOUT
PGOOD
CSP2
CSN2
CLP2
OVPIN
PHASE-
LOCKED
LOOP
RAMP
GENERATOR
RAMP2
POWER-
GOOD
GENERATOR
CLP2
CLP1
VREF
DIFF
CLKIN
PHASE
CLKOUT
PLLCMP
DIFF
AMP
ERROR
AMP
SENSE-
SENSE+
DIFF
EAN
EAOUT
PGND
PGND
PGND
SGND
VREF = 0.8V + VCM
+5V
LDO
REGULATOR
UVLO
POR
TEMP SENSOR
+0.6V
0.8V OVP
COMP
N
Functional Diagrams (continued)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
14 ______________________________________________________________________________________
MAX5067
Q4
Q3
C39 C40
R3
D2
Q2
D1
VIN
C8
C11
Q1
VIN
VCC
D4
D3
C41
C12
C38
C3–C7
C14
C15
C16
C25
C26,
C30,
C37
LOAD
L2 R2
L1 R1
DH1
LX1
DL1
BST1
VDD
VCC
DH2
LX2
DL2
BST2
CSP2CSN2PGOODPHASESGNDPGNDCLP2CLP1
R11
PGOOD
VCC
R6
C35
C36
R5
C33
C34
C42
C1, C2
R13
VCC
C31
C32
R4
CSP1CSN1SENSE+SENSE-INCLKINPLLCMPEN
Rf
RIN
R12
C43
VIN
EAOUT
EAN
DIFF
OVPIN
OVPOUT
C13
IN
IN
C44
RA
RB
RH
RL
VCC
RX
VOUT = +0.8V TO
+3.3V AT 52A
VIN = +5V
Figure 1. Typical Application Circuit, VIN = +5V
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 15
MAX5067
Q4
Q3
C39 C40
R3
D2
Q2
D1
VIN
C8
C11
Q1
VIN
VCC
D4
D3
C41
C12
C38
C3C7
C14,
C15
C16
C25
C26
C30,
C37
LOAD
L2 R2
L1 R1
DH1
LX1
DL1
BST1
VDD
VCC
DH2
LX2
DL2
BST2
CSP2CSN2PGOODPHASESGNDPGNDCLP2CLP1
R11
PGOOD
VCC
R6
C35
C36
R5
C33
C34
C42
C1, C2
R13
VCC
C31
C32
R4
CSP1CSN1SENSE+SENSE-INCLKINPLLCMPEN
Rf
RIN
R12
C43
VIN
EAOUT
EAN
DIFF
OVPIN
OVPOUT
C13
C44
RA
RB
RH
RL
VCC
RX
VOUT = +1.8V AT 52A
VIN = +8V TO +28V
NOTE: SEE TABLE 1 FOR COMPONENT VALUES.
Figure 2. Typical VRM Application Circuit, VIN = +8V to +28V
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
16 ______________________________________________________________________________________
CLKIN
PLLCMP
PGND
PHASE
DL2
LX2
DH2
DL1
LX1
DH1
VCC
EAOUT
EAN
DIFF
EN
CSP2
CSN2
CSP1
CSN1
MAX5065
3
R1
C39
VIN = +12V
C1,
C2
21
15
IN
C25
C26
R4
R7
R8
R6
C29
C30
R5
C27
C28
SGND
CLP2
CLP1 Q2
Q1
D2
Q2
D1
VIN
Q1
VIN
D4
D3
C32
C12
C31
C3C7
L2 R3
L1 R2
C13
C8C11 C14,
C15
C16C24,
C33 LOAD
+1.8V AT 60A
VOUT
SENSE-
SENSE+
17
18
19
16
20
25
24
23
26
9
8
14
13
1
2
BST1
VCC
28
4
10
11
12
7
5
6
22
BST2
RH
RL
VCC
RX
C34
Figure 3. MAX5065 Typical Application Circuit
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 17
where, QG1, QG2, QG3, and QG4 are the total gate
charge of the low-side and high-side external
MOSFETs, IQis 4mA (typ), and fSW is the switching fre-
quency of each individual phase.
For applications utilizing a +5V input voltage, disable
the VCC regulator by connecting IN and VCC together.
Undervoltage Lockout (UVLO)/Soft-Start
The MAX5065/MAX5067 include an undervoltage lock-
out with hysteresis and a power-on reset circuit for con-
verter turn-on and monotonic rise of the output voltage.
The UVLO threshold is internally set between +4.0V
and +4.5V with a 200mV hysteresis. Hysteresis at
UVLO eliminates chattering during startup.
Most of the internal circuitry, including the oscillator,
turns on when the input voltage reaches +4V. The
MAX5065/MAX5067 draw up to 4mA of current before
the input voltage reaches the UVLO threshold.
The compensation network at the current-error ampli-
fiers (CLP1 and CLP2) provides an inherent soft-start of
the output voltage. It includes a parallel combination of
capacitors (C34, C36) and resistors (R5, R6) in series
with other capacitors (C33, C35) (see Figures 1 and 2).
The voltage at CLP_ limits the maximum current avail-
able to charge output capacitors. The capacitor on
CLP_ in conjunction with the finite output-drive current
of the current-error amplifier yields a finite rise time for
the output current and thus the output voltage.
Internal Oscillator
The internal oscillator generates the 180°out-of-phase
clock signals required by the pulse-width modulation
(PWM) circuits. The oscillator also generates the 2VP-P
voltage ramp signals necessary for the PWM compara-
tors. Connect CLKIN to SGND to set the internal oscillator
frequency to 250kHz or connect CLKIN to VCC to set the
internal oscillator to 500kHz.
CLKIN is a CMOS logic clock input for the phase-
locked loop (PLL). When driven externally, the internal
oscillator locks to the signal at CLKIN. A rising edge at
CLKIN starts the ON cycle of the PWM. Ensure that the
external clock pulse width is at least 200ns. CLKOUT
provides a phase-shifted output with respect to the ris-
ing edge of the signal at CLKIN. PHASE sets the
amount of phase shift at CLKOUT. Connect PHASE to
VCC for 120°of phase shift, leave PHASE unconnected
for 90°of phase shift, or connect PHASE to SGND for
60°of phase shift with respect to CLKIN.
The MAX5065/MAX5067 require compensation on
PLLCMP even when operating from the internal oscillator.
The device requires an active PLL to generate the proper
clock signal required for PWM operation.
Control Loop
The MAX5065/MAX5067 use an average-current-mode
control scheme to regulate the output voltage (Figure
4). The main control loop consists of an inner current
loop and an outer voltage loop. The inner loop controls
the output currents (IPHASE1 and IPHASE2) while the
outer loop controls the output voltage. The inner current
loop absorbs the inductor pole reducing the order of
the outer voltage loop to that of a singlepole system.
The current loop consists of a current-sense resistor
(RS), a current-sense amplifier (CA_), a current-error
amplifier (CEA_), an oscillator providing the carrier
ramp, and a PWM comparator (CPWM_). The precision
CA_ amplifies the sense voltage across RSby a factor
of 18. The inverting input to the CEA_ senses the CA_
output. The CEA_ output is the difference between the
voltage-error amplifier output (EAOUT) and the gained-
up voltage from the CA_. The RC compensation net-
work connected to CLP1 and CLP2 provides external
frequency compensation for the respective CEA_. The
start of every clock cycle enables the high-side drivers
and initiates a PWM ON cycle. Comparator CPWM_
compares the output voltage from the CEA_ with a 0 to
+2V ramp from the oscillator. The PWM ON cycle termi-
nates when the ramp voltage exceeds the error voltage.
The outer voltage control loop consists of the differen-
tial amplifier (DIFF AMP), reference voltage, and VEA.
The unity-gain differential amplifier provides true differ-
ential remote sensing of the output voltage. The differ-
ential amplifier output connects to the inverting input
(EAN) of the VEA. The noninverting input of the VEA is
internally connected to an internal precision reference
voltage. The MAX5067 reference voltage is set to +0.8V
and the MAX5065 reference is set to +0.6V. The VEA
controls the two inner current loops (Figure 4). Use a
resistive feedback network to set the VEA gain as
required by the adaptive voltage-positioning circuit
(see the Adaptive Voltage Positioning section).
Current-Sense Amplifier
The differential current-sense amplifier (CA_) provides a
DC gain of 18. The maximum input offset voltage of the
current-sense amplifier is 1mV and the common-mode
voltage range is -0.3V to +3.6V. The current-sense ampli-
fier senses the voltage across a current-sense resistor.
Peak-Current Comparator
The peak-current comparator provides a path for fast
cycle-by-cycle current limit during extreme fault condi-
tions such as an output inductor malfunction (Figure 5).
Note that the average current-limit threshold of 48mV
still limits the output current during short-circuit condi-
tions. To prevent inductor saturation, select an output
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
18 ______________________________________________________________________________________
inductor with a saturation current specification greater
than the average current limit (48mV). Proper inductor
selection ensures that only extreme conditions trip the
peak-current comparator, such as a cracked output
inductor. The 112mV voltage threshold for triggering
the peak-current limit is twice the full-scale average
current-limit voltage threshold. The peak-current com-
parator has a delay of only 260ns.
Current-Error Amplifier
Each phase of the MAX5065/MAX5067 has a dedicated
transconductance current-error amplifier (CEA_) with a
typical gmof 550µS and 320µA output sink and source
current capability. The current-error amplifier outputs,
CLP1 and CLP2, serve as the inverting input to the
PWM comparator. CLP1 and CLP2 are externally
accessible to provide frequency compensation for the
inner current loops (Figure 4). Compensate CEA_ so
the inductor current down slope, which becomes the
up slope to the inverting input of the PWM comparator,
is less than the slope of the internally generated voltage
ramp (see the Compensation section).
PWM Comparator and R-S Flip-Flop
The PWM comparator (CPWM) sets the duty cycle for
each cycle by comparing the output of the current-error
amplifier to a 2VP-P ramp. At the start of each clock
cycle, an R-S flip-flop resets and the high-side driver
(DH_) turns on. The comparator sets the flip-flop as
soon as the ramp voltage exceeds the CLP_ voltage,
thus terminating the ON cycle (Figure 5).
Differential Amplifier
The differential amplifier (DIFF AMP) facilitates output
voltage remote sensing at the load (Figure 4). It pro-
vides true differential output voltage sensing while
rejecting the common-mode voltage errors due to high-
current ground paths. Sensing the output voltage
DRIVE 2
DRIVE 1
CPWM1
CPWM2
CEA1
CEA2
VEA
DIFF
AMP
CA1
CA2
VREF
CLP2
CSP2
CSN2
CLP1
CSN1
CSP1
SENSE+
SENSE-
VIN
VIN
LOAD
COUT
VOUT
RIN*
RF*
RS
RS
IPHASE1
IPHASE2
RCF
CCFF
CCF
RCF
CCCF
CCF
*RF AND RIN ARE EXTERNAL.
MAX5065/
MAX5067
Figure 4. MAX5065/MAX5067 Control Loop
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 19
directly at the load provides accurate load voltage
sensing in high-current environments. The VEA pro-
vides the difference between the differential amplifier
output (DIFF) and the desired output voltage. The dif-
ferential amplifier has a bandwidth of 3MHz. The differ-
ence between SENSE+ and SENSE- regulates to +0.6V
for the MAX5065 and regulates to +0.8V for the
MAX5067. Connect SENSE+ to the center of the resis-
tive-divider from the output to SENSE-.
Voltage-Error Amplifier
The VEA sets the gain of the voltage control loop and
determines the error between the differential amplifier
output and the internal reference voltage (VREF).
The VEA output clamps to +0.9V relative to VCM
(+0.6V), thus limiting the average maximum current
from individual phases. The maximum average current-
limit threshold for each phase is equal to the maximum
clamp voltage of the VEA divided by the gain (18) of
the current-sense amplifier. This results in accurate set-
tings for the average maximum current for each phase.
Set the VEA gain using RFand RIN for the amount of
output voltage positioning required within the rated cur-
rent range as discussed in the Adaptive Voltage
Positioning section (Figure 4).
where RHand RLare the feedback resistor network
(Figures 1, 2). VREF = 0.6V (MAX5065) or 0.8V
(MAX5067).
Some applications require VOUT equal to VOUT(NOM) at
no load. To ensure that the output voltage does not
exceed the nominal output voltage (VOUT(NOM)), add a
resistor RXfrom VCC to EAN.
Use the following equations to calculate the value of RX.
For MAX5065:
For MAX5067:
Adaptive Voltage Positioning
Powering new-generation processors requires new
techniques to reduce cost, size, and power dissipation.
Voltage positioning reduces the total number of output
capacitors to meet a given transient response require-
ment. Setting the no-load output voltage slightly higher
than the output voltage during nominally loaded condi-
tions allows a larger downward voltage excursion when
the output current suddenly increases. Regulating at a
lower output voltage under a heavy load allows a larger
upward-voltage excursion when the output current sud-
denly decreases. A larger allowed, voltage-step excur-
sion reduces the required number of output capacitors
RV R
V
XCC F
=−×[.]
.
14 08
RV R
V
XCC F
=−×[.]
.
12 06
VR
R
RR
R
V
OUT NL IN
F
HL
L
REF()
=+
×+
×1
2 x fs (V/s)
RAMP
CLK
CSP_
CSN_
GMIN
SHDN
CLP_
DRV_VCC
BST_
DH_
LX_
DL_
PGND
AV = 18
PWM
COMPARATOR
PEAK-CURRENT
COMPARATOR
112mV
S
R
Q
Q
Gm =
500µS
Figure 5. Phase Circuit (Phase 1/Phase 2)
(3)
(4)
(5)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
20 ______________________________________________________________________________________
or allows for the use of higher ESR capacitors.
Voltage positioning may require the output to regulate
away from a center value. Define the center value as the
voltage where the output drops (VOUT/2) at one half the
maximum output current (Figure 6).
Set the voltage-positioning window (VOUT) using the
resistive feedback of the VEA. Use the following equa-
tions to calculate the voltage-positioning window for the
MAX5065/MAX5067:
where RIN and RFare the input and feedback resistors of
the VEA, GCis the current-loop transconductance, and
RSis the current-sense resistor.
Phase-Locked Loop: Operation and
Compensation
The PLL synchronizes the internal oscillator to the
external frequency source when driving CLKIN.
Connecting CLKIN to VCC or SGND forces the PWM
frequency to default to the internal oscillator frequency
of 500kHz or 250kHz, respectively. The PLL uses a
conventional architecture consisting of a phase detec-
tor and a charge pump capable of providing 20µA of
output current. Connect an external series combination
capacitor (C31) and resistor (R4) and a parallel capaci-
tor (C32) from PLLCMP to SGND to provide frequency
compensation for the PLL (Figure 1). The pole-zero pair
compensation provides a zero defined by 1 / [R4 x
(C31 + C32)] and a pole defined by 1 / (R4 x C32). Use
the following typical values for compensating the PLL:
R4 = 7.5k, C31 = 4.7nF, C32 = 470pF. If changing the
PLL frequency, expect a finite locking time of approxi-
mately 200µs.
The MAX5065/MAX5067 require compensation on
PLLCMP even when operating from the internal oscilla-
tor. The device requires an active PLL in order to gen-
erate the proper internal PWM clocks.
MOSFET Gate Drivers (DH_, DL_)
The high-side (DH_) and low-side (DL_) drivers drive
the gates of external N-channel MOSFETs (Figures 1, 2,
and 3). The drivers high-peak sink and source current
capability provides ample drive for the fast rise and fall
times of the switching MOSFETs. Faster rise and fall
times result in reduced cross-conduction losses. For
modern CPU voltage-regulating module applications
where the duty cycle is less than 50%, choose high-
side MOSFETs (Q1 and Q3) with a moderate RDS(ON)
and a very low gate charge. Choose low-side
MOSFETs (Q2 and Q4) with very low RDS(ON) and
moderate gate charge.
The driver block also includes a logic circuit that provides
an adaptive nonoverlap time to prevent shoot-through
currents during transition. The typical nonoverlap time is
60ns between the high-side and low-side MOSFETs.
BST_
The MAX5067 uses VDD to power the low- and high-
side MOSFET drivers. The high-side drivers derive their
power through a bootstrap capacitor and VDD supplies
power internally to the low-side drivers. Connect a
0.47µF low-ESR ceramic capacitor between BST_ and
LX_. Bypass VCC to SGND with 4.7µF and 0.1µF low-
ESR ceramic capacitors in parallel. Reduce the PC
board area formed by these capacitors, the rectifier
diodes between VCC and the boost capacitor, the
MAX5065/MAX5067, and the switching MOSFETs.
Overload Conditions
Average-current-mode control has the ability to limit the
average current sourced by the converter during a fault
condition. When a fault condition occurs, the VEA out-
put clamps to +0.9V with respect to the common-mode
voltage (VCM = +0.6V) and is compared with the output
of the current-sense amplifiers (CA1 and CA2) (see
Figure 4). The current-sense amplifiers gain of 18 limits
the maximum current in the inductor or sense resistor to
ILIMIT = 50mV/RS.
G
R
C
S
=005.
VIR
GR
RR
R
OUT OUT IN
CF
HL
L
=×
×××+
2
(6)
(7)
LOAD (A)
VCNTR
NO LOAD 1/2 LOAD FULL LOAD
VOLTAGE-POSITIONING WINDOW
VCNTR + VOUT/2
VCNTR - VOUT/2
Figure 6. Defining the Voltage-Positioning Window
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 21
Protection
The MAX5067 includes output overvoltage protection
(OVP), undervoltage protection (UVP), phase failure,
and overload protection to prevent damage to the pow-
ered electronic circuits.
Overvoltage Protection (MAX5067)
The OVP comparator compares the OVPIN input to the
overvoltage threshold (Figure 7). The overvoltage
threshold is typically +0.8V. A detected overvoltage
event latches the comparator output forcing the power
stage into the OVP state. In the OVP state, the high-
side MOSFETs turn off and the low-side MOSFETs latch
on. Use the OVPOUT high-current output driver to turn
on an external crowbar SCR. When the crowbar SCR
turns on, a fuse must blow or the source current for the
MAX5067 regulator must be limited to prevent further
damage to the external circuitry. Connect the SCR
close to the input source and after the fuse. Use an
SCR large enough to handle the peak I2t energy due to
the input and output capacitors discharging and the
current sourced by the power-source output. Connect
DIFF to OVPIN for differential output sensing and over-
voltage protection. Add an RC delay to reduce the sen-
sitivity of the overvoltage circuit and avoid nuisance
tripping of the converter (Figures 1, 2). Connect a resis-
tor-divider from the load to SGND to set the OVP output
voltage.
Power-Good Generator (MAX5067)
The PGOOD output is high if all of the following condi-
tions are met (Figure 8):
1) The output is within 90% to 108% of the pro-
grammed output voltage.
2) Both phases are providing current.
3) EN is high.
A window comparator compares the differential amplifier
output (DIFF) against 1.08 times the set output voltage
for overvoltage and 0.90 times the set output voltage for
undervoltage monitoring. The phase-failure comparator
detects a phase failure by comparing the current-error-
amplifier output (CLP_) with a 2.0V reference.
Use a 10kpullup resistor from PGOOD to a voltage
source less than or equal to VCC. An output voltage
outside the comparator window or a phase-failure con-
dition forces the open-drain output low. The open-drain
MOSFET sinks 4mA of current while maintaining less
than 0.2V at the PGOOD output.
VR
RV
OVP A
B
=+
×108.
MAX5067
RF
RIN
OVPIN
DIFF
EAN
EAOUT
RB
RA
VOUT
Figure 7. OVP Input Delay
+2.0V
PHASE-FAILURE DETECTION
CLP2
CLP1
VREF
DIFF
PGOOD
8% OF VREF
10% OF VREF
Figure 8. Power-Good Generator (MAX5067)
(8)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
22 ______________________________________________________________________________________
CLKIN
CLKOUTSGNDPGND
IN
PHASE
DL2
LX2
DH2
DL1
LX1
DH1
VCC
VIN
EAOUT
EAN
DIFF
SENSE-
SENSE+
CSP2
CSN2
CSP1
CSN1
VCC
VIN
VIN
CLKOUTSGNDPGND
IN
PHASE
DL2
LX2
DH2
DL1
LX1
DH1
EAOUT
EAN
CLKIN
CSP2
CSN2
CSP1
CSN1
DIFF
VCC
VIN
VIN
CLKOUTSGNDPGND
IN
PHASE
DL2
LX2
DH2
DL1
LX1
DH1
EAOUT
EAN
CLKIN
CSP2
CSN2
CSP1
CSN1
DIFF
VCC
VIN
VIN
TO OTHER MAX5065/MAX5067s
MAX5065/
MAX5067
MAX5065/
MAX5067
MAX5065/
MAX5067
LOAD VOUT = +0.6V (MAX5065)
VOUT = +0.8V (MAX5067)
Figure 9. Parallel Configuration of Multiple MAX5065/MAX5067s
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 23
MAX5067
(MASTER)
Q4
Q3
D2
Q2
D1
VIN
4 x 22µF
C8C11
Q1
VIN
VIN = +12V
VCC
D4
D3
C41
0.1µF
C12
0.47µF
C38
4.7µF
C3C7
5 x 22µF
L2
0.6µH
R2
1.35m
L1
0.6µH
R1
1.35m
DH1
LX1
DL1
BST1
VCC
VDD
DH2
LX2
DL2
BST2
CSP2CSN2PGOODPHASECLKOUTSGNDPGNDCLP2CLP1
R11
PGOOD
VCC
R6
C35
C36
R5
C33
C34
C42
0.1µF
C1, C2
2 x 47µF
R13
2.2
C31
C32
R4
CSP1CSN1SENSE+SENSE-INCLKINPLLCMPOVPOUT
R8
R7
EAOUT
EAN
DIFF
OVPIN
EN
C13
0.47µF
C14, C15,
C44, C45
2 x 100µF
C16C25,
C57C60
2 x 270µF
C26C30,
C37
6
x
10µF
LOAD
VOUT = +0.8V TO
+3.3V AT 104A
VCC
MAX5067
(SLAVE)
Q8
Q7
D6
Q6
D5
VIN C51C54
4 x 22µF
Q5
VIN
D8
D7
C64
0.1µF
C55
0.47µF
C65
4.7µF
C46C50
5 x 22µF
L4
0.6µH
R15
1.35m
L3
0.6µH
R14
1.35m
DH1
LX1
DL1
BST1
VCC
VDD
DH2
LX2
DL2
BST2
CSP2CSN2PHASE PGOODSGNDPGNDCLP2CLP1
VCC
R19
C67
C66
R18
C68
C69
C61
0.1µF
R24
2.2
C70
C71
R17
CSP1CSN1SENSE+SENSE-CLKININPLLCMPEN
R21
R20
EAOUT
EAN
DIFF
OVPIN
OVPOUT
C56
0.47µF
R12
C43
VIN
C39
1µF
C40
1µF
R
H
R
L
RA
RB
C62
1µF
C63
0.1µF
R16
R3
Figure 10. Four-Phase Parallel Application Circuit (VIN = +12V, VOUT = +0.8V to +3.3V at 104A)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
24 ______________________________________________________________________________________
Phase-Failure Detector (MAX5067)
Output current contributions from the two phases are
within ±10% of each other. Proper current sharing
reduces the necessity to overcompensate the external
components. However, an undetected failure of one
phase driver causes the other phase driver to run con-
tinuously as it tries to provide the entire current require-
ment to the load. Eventually, the stressed operational
phase driver fails.
During normal operating conditions, the voltage level
on CLP_ is within the peak-to-peak voltage levels of the
PWM ramp. If one of the phases fails, the control loop
raises the CLP_ voltage above its operating range. To
determine a phase failure, the phase-failure detection
circuit (Figure 8) monitors the output of the current
amplifiers (CLP1 and CLP2) and compares them to a
2.0V reference. If the voltage levels on CLP1 or CLP2
are above the reference level for more than 1250 clock
cycles, the phase failure circuit forces PGOOD low.
Parallel Operation
For applications requiring large output current, parallel
up to three MAX5065/MAX5067s (six phases) to triple
the available output current (see Figures 9 and 10). The
paralleled converters operate at the same switching fre-
quency but different phases keep the capacitor ripple
RMS currents to a minimum. Three parallel MAX5065/
MAX5067 converters deliver up to 180A of output cur-
rent. To set the phase shift of the on-board PLL, leave
PHASE unconnected for 90°of phase shift (2 paralleled
converters), or connect PHASE to SGND for 60°of phase
shift (3 converters in parallel). Designate one converter
as master and the remaining converters as slaves.
Connect the master and slave controllers in a daisy-
chain configuration as shown in Figure 9. Connect CLK-
OUT from the master controller to CLKIN of the first
slaved controller, and CLKOUT from the first slaved con-
troller to CLKIN of the second slaved controller. Choose
the appropriate phase shift for minimum ripple currents
at the input and output capacitors. The master controller
senses the output differential voltage through SENSE+
and SENSE- and generates the DIFF voltage. Disable the
voltage sensing of the slaved controllers by leaving DIFF
unconnected (floating). Figure 10 shows a detailed typi-
cal parallel application circuit using two MAX5067s. This
circuit provides four phases at an input voltage of +12V
and an output voltage range of +0.6V to +3.3V
(MAX5065) and +0.8V to +3.3V (MAX5067) at 104A.
Applications Information
Each MAX5065/MAX5067 circuit drives two 180°out-of-
phase channels. Parallel two or three MAX5065/
MAX5067 circuits to achieve four- or six-phase opera-
tion, respectively. Figure 1 shows the typical application
circuit for a two-phase operation. The design criteria for
a two-phase converter includes frequency selection,
inductor value, input/output capacitance, switching
MOSFETs, sense resistors, and the compensation net-
work. Follow the same procedure for the four- and six-
phase converter design, except for the input and output
capacitance. The input and output capacitance require-
ments vary depending on the operating duty cycle.
The examples discussed in this data sheet pertain to a
typical application with the following specifications:
VIN = +12V
VOUT = +1.8V
IOUT(MAX) = 52A
fSW = 250kHz
Peak-to-Peak Inductor Current (IL) = 10A
Table 1 shows a list of recommended external compo-
nents (Figure 1) and Table 2 provides component sup-
plier information.
Number of Phases
Selecting the number of phases for a voltage regulator
depends mainly on the ratio of input-to-output voltage
(operating duty cycle). Optimum output-ripple cancella-
tion depends on the right combination of operating duty
cycle and the number of phases. Use the following
equation as a starting point to choose the number of
phases:
NPH K/D (9)
where K = 1, 2, or 3 and the duty cycle is D = VOUT/VIN.
Choose K to make NPH an integer number. For exam-
ple, converting VIN = +12V to VOUT = +1.8V yields
better ripple cancellation in the six-phase converter
than in the four-phase converter. Ensure that the output
load justifies the greater number of components for
multiphase conversion. Generally limiting the maximum
output current to 25A per phase yields the most cost-
effective solution. The maximum ripple cancellation
occurs when NPH = K/D.
Single-phase conversion requires greater size and power
dissipation for external components such as the switch-
ing MOSFETs and the inductor. Multiphase conversion
eliminates the heatsink by distributing the power dissipa-
tion in the external components. The multiple phases
operating at given phase shifts effectively increase the
switching frequency seen by the input/output capacitors,
thereby reducing the input/output capacitance require-
ment for the same ripple performance. The lower induc-
tance value improves the large-signal response of the
converter during a transient load at the output. Consider
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 25
Table 1. Component List
DESIGNATION QTY DESCRIPTION
C1, C2 2 47µF,16V X5R input-filter capacitors TDK C5750X5R1C476M
C3C11 9 22µF, 16V input-filter capacitors TDK C4532X5R1C226M
C12, C13 2 0.47µF, 16V capacitors TDK C1608X5R1A474K
C14, C15 2 100µF, 6.3V, output-filter capacitors Murata GRM44-1X5R107K6.3
C16C25 10 270µF, 2V output-filter capacitors Panasonic EEFUE0D271R
C26C30, C37 6 10µF, 6.3V output-filter capacitors TDK C2012X5R05106M
C31 1 4700pF, 16V X7R capacitor Vishay-Siliconix VJ0603Y471JXJ
C32, C34, C36 3 470pF, 16V capacitors Murata GRM1885C1H471JAB01
C33, C35, C43 3 0.01µF, 50V X7R capacitors Murata GRM188R71H103KA01
C38 1 4.7µF, 16V X5R capacitor Murata GRM40-034X5R475k6.3
C39 1 0.1µF, 10V Y5V capacitor Murata GRM188F51A105
C40, C41, C42 3 0.1µF, 16V X7R capacitors Murata GRM188R71C104KA01
C44 1 100pFOVPIN capacitor
D1, D2 2 Schottky diodes ON-Semiconductor MBRS340T3
D3, D4 2 Schottky diodes ON-Semiconductor MBR0520LT1
L1, L2 2 0.6µH, 27A inductors Panasonic ETQP1H0R6BFX
Q1, Q3 2 Upper-power MOSFETs Vishay-Siliconix Si7860DP
Q2, Q4 2 Lower-power MOSFETs Vishay-Siliconix Si7886DP
R1, R2 4 Current-sense resistors, use two 2.7m resistors in parallel, Panasonic ERJM1WSF2M7U
R3, R13 2 2.2 ±1% resistors
R4 2 7.5k ±1% resistor
R5, R6 2 1k ±1% resistors
RIN 1 4.99k ±1% resistor
Rf1 37.4k ±1% resistor
R11 1 10k ±1% resistor
R12 1 10k ±1% resistor
RA 1 See the Overvoltage Protection (MAX5067) section
RB 1 See the Overvoltage Protection (MAX5067) section
RH 1 See the Adaptive Voltage Positioning and Voltage-Error Amplifier sections
RL 1 See the Adaptive Voltage Positioning and Voltage-Error Amplifier sections
RX 1 Open circuit
Table 2. Component Suppliers
SUPPLIER PHONE FAX WEBSITE
Murata 770-436-1300 770-436-3030 www.murata.com
ON Semiconductor 602-244-6600 602-244-3345 www.on-semi.com
Panasonic 714-373-7939 714-373-7183 www.panasonic.com
TDK 847-803-6100 847-390-4405 www.tcs.tdk.com
Vishay-Siliconix 1-800-551-6933 619-474-8920 www.vishay.com
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
26 ______________________________________________________________________________________
all these issues when determining the number of phases
necessary for the voltage regulator application.
Inductor Selection
The switching frequency per phase, peak-to-peak rip-
ple current in each phase, and allowable ripple at the
output determine the inductance value.
Selecting higher switching frequencies reduces the
inductance requirement, but at the cost of lower efficien-
cy. The charge/discharge cycle of the gate and drain
capacitances in the switching MOSFETs create switching
losses. The situation worsens at higher input voltages,
since switching losses are proportional to the square of
input voltage. Use 500kHz per phase for VIN = +5V and
250kHz or less per phase for VIN >+12V.
Although lower switching frequencies per phase increase
the peak-to-peak inductor ripple current (IL), the ripple
cancellation in the multiphase topology reduces the input
and output capacitor RMS ripple current.
Use the following equation to determine the minimum
inductance value:
Choose ILequal to about 40% of the output current
per phase. Since ILaffects the output-ripple voltage,
the inductance value may need minor adjustment after
choosing the output capacitors for full-rated efficiency.
Choose inductors from the standard high-current,
surface-mount inductor series available from various
manufacturers. Particular applications may require cus-
tom-made inductors. Use high-frequency core material
for custom inductors. High ILcauses large peak-to-peak
flux excursion increasing the core losses at higher fre-
quencies. The high-frequency operation coupled with
high IL, reduces the required minimum inductance
and even makes the use of planar inductors possible.
The advantages of using planar magnetics include low-
profile design, excellent current-sharing between phas-
es due to the tight control of parasitics, and low cost.
For example, calculate the minimum inductance at
VIN(MAX) = +13.2V, VOUT = +1.8V, IL= 10A, and fSW =
250kHz:
The average-current-mode control feature of the
MAX5065/MAX5067 limits the maximum peak inductor
current and prevents the inductor from saturating.
Choose an inductor with a saturating current greater
than the worst-case peak inductor current. Use the fol-
lowing equation to determine the worst-case inductor
current for each phase:
where RSENSE is the sense resistor in each phase.
Switching MOSFETs
When choosing a MOSFET for voltage regulators,
consider the total gate charge, RDS(ON), power dissipa-
tion, and package thermal impedance. The product of
the MOSFET gate charge and on-resistance is a figure of
merit, with a lower number signifying better performance.
Choose MOSFETs optimized for high-frequency switch-
ing applications.
The average gate-drive current from the MAX5065/
MAX5067 output is proportional to the total capacitance it
drives from DH1, DH2, DL1, and DL2. The power dissi-
pated in the MAX5065/MAX5067 is proportional to the
input voltage and the average drive current. See the VIN,
VCC, VDD section to determine the maximum total gate
charge allowed from all the driver outputs combined.
The gate charge and drain capacitance (CV2) loss, the
cross-conduction loss in the upper MOSFET due to
finite rise/fall time, and the I2R loss due to RMS current
in the MOSFET RDS(ON) account for the total losses in
the MOSFET. Estimate the power loss (PDMOS_) in the
high-side and low-side MOSFETs using the following
equations:
where QG, RDS(ON), tR, and tFare the upper-switching
MOSFETs total gate charge, on-resistance at +25°C,
rise time, and fall time, respectively.
where D = VOUT/VIN, IDC = (IOUT - IL)/2 and IPK =
(IOUT + IL)/2
IIIII
D
RMS HI DC PK DC PK=++×
()
×
22
3
PD Q V f
VI tt f RI
MOS HI G DD SW
IN OUT R F SW DS ON RMS HI
×
()
+
××+
()
×
414 2
.()
IV
R
I
L PEAK SENSE
L
_
.
=+
0 051
2
LkH
MIN =
()
×
××
13 2 1 8 1 8
13 2 250 10 06
.. .
..
LVVV
Vf I
MIN INMAX OUT OUT
IN SW L
=
()
×
××
(10)
(11)
(12)
(13)
(14)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 27
where COSS is the MOSFET drain-to-source capacitance.
For example, from the typical specifications in the
Applications Information section with VOUT = +1.8V, the
high-side and low-side MOSFET RMS currents are 9.9A
and 24.1A, respectively. Ensure that the thermal imped-
ance of the MOSFET package keeps the junction tem-
perature at least 25°C below the absolute maximum
rating. Use the following equation to calculate maxi-
mum junction temperature:
TJ= PDMOS x θJ-A + TA
Input Capacitors
The discontinuous input-current waveform of the buck
converter causes large ripple currents in the input
capacitor. The switching frequency, peak inductor cur-
rent, and the allowable peak-to-peak voltage ripple
reflected back to the source dictate the capacitance
requirement. Increasing the number of phases increas-
es the effective switching frequency and lowers the
peak-to-average current ratio, yielding a lower input
capacitance requirement.
The input ripple is comprised of VQ(caused by the
capacitor discharge) and VESR (caused by the ESR of
the capacitor). Use low-ESR ceramic capacitors with
high-ripple-current capability at the input. Assume the
contributions from the ESR and capacitor discharge are
equal to 30% and 70%, respectively. Calculate the
input capacitance and ESR required for a specified rip-
ple using the following equation:
where IOUT is the total output current of the multiphase
converter and N is the number of phases.
For example, at VOUT = +1.8V, the ESR and input
capacitance are calculated for the input peak-to-peak
ripple of 100mV or less yielding an ESR and capaci-
tance value of 1mand 200µF.
Output Capacitors
The worst-case peak-to-peak and capacitor RMS ripple
current, the allowable peak-to-peak output ripple volt-
age, and the maximum deviation of the output voltage
during step loads determine the capacitance and the
ESR requirements for the output capacitors.
In multiphase converter design, the ripple currents from
the individual phases cancel each other and lower the
ripple current. The degree of ripple cancellation
depends on the operating duty cycle and the number of
phases. Choose the right equation from Table 3 to calcu-
late the peak-to-peak output ripple (IP-P) for a given
duty cycle of two-, four-, and six-phase converters. The
maximum ripple cancellation occurs when NPH = K / D.
C
I
NDD
Vf
IN
OUT
QSW
=×−
()
×
1
ESR V
I
N
I
IN ESR
OUT L
=
()
+
2
IIIII
D
RMS LO DC PK DC PK=++×
()
×
()
22 1
3
PD Q V f
CVf RI
MOS LO G DD SW
OSS IN SW DS ON RMS LO
×
()
+
×××
2
314
22
.()
Table 3. Peak-to-Peak Output Ripple
Current Calculations
NUMBER OF
PHASES (N)
DUTY
CYCLE (D) EQUATION FOR IP-P
2 < 50%
2 > 50%
4 0 to 25%
4 25% to 50%
4 > 50%
6 < 17%
IVD
Lf
O
SW
=
×
()12
IVVD
Lf
IN O
SW
=
()
()
×
21
IVD
Lf
O
SW
=
×
()14
IVDD
DLf
O
SW
=−−
×××
()()12 4 1
2
IVD D
DLf
O
SW
=−−
××
()( )2134
IVD
Lf
O
SW
=
×
()16
(15)
(16)
(17) (18)
(19)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
28 ______________________________________________________________________________________
The allowable deviation of the output voltage during the
fast transient load dictates the output capacitance and
ESR. The output capacitors supply the load step until
the controller responds with a greater duty cycle. The
response time (tRESPONSE) depends on the closed-loop
bandwidth of the converter. The resistive drop across
the capacitor ESR and capacitor discharge causes a
voltage drop during a step load. Use a combination of
SP polymer and ceramic capacitors for better transient
load and ripple/noise performance.
Keep the maximum output voltage deviation less than
or equal to the adaptive voltage-positioning window
(VOUT). Assume 50% contribution each from the out-
put capacitance discharge and the ESR drop. Use the
following equations to calculate the required ESR and
capacitance value:
where ISTEP is the load step and tRESPONSE is the
response time of the controller. Controller response
time depends on the control-loop bandwidth.
Current Limit
The average-current-mode control technique of the
MAX5065/MAX5067 accurately limits the maximum out-
put current per phase. The MAX5065/MAX5067 sense
the voltage across the sense resistor and limit the peak
inductor current (IL-PK) accordingly. The ON cycle ter-
minates when the current-sense voltage reaches 45mV
(min). Use the following equation to calculate maximum
current-sense resistor value:
where PDRis the power dissipation in sense resistors.
Select 5% lower value of RSENSE to compensate for any
parasitics associated with the PC board. Also, select a
non inductive resistor with the appropriate wattage rating.
Reverse Current Limit
The MAX5065/MAX5067 limit the reverse current when
VBUS is higher than the preset output voltage.
Calculate the maximum reverse current based on VCLR,
the reverse-current-limit threshold, and the current-sense
resistor.
where IREVERSE is the total reverse current into the con-
verter.
Compensation
The main control loop consists of an inner current loop
and an outer voltage loop. The MAX5065/MAX5067 use
an average-current-mode control scheme to regulate
the output voltage (Figure 4). IPHASE1 and IPHASE2 are
the inner average current loops. The VEA output pro-
vides the controlling voltage for these current sources.
The inner current loop absorbs the inductor pole reduc-
ing the order of the outer voltage loop to that of a sin-
gle-pole system.
A resistive feedback around the VEA provides the best
possible response, since there are no capacitors to
charge and discharge during large-signal excursions, RF
and RIN determine the VEA gain. Use the following equa-
tion to calculate the value for RF:
where GCis the current-loop transconductance and N
is number of phases.
When designing the current-control loop ensure that the
inductor downslope (when it becomes an upslope at the
CEA output) does not exceed the ramp slope. This is a
necessary condition to avoid sub-harmonic oscillations
similar to those in peak current-mode control with insuffi-
cient slope compensation. Use the following equation to
calculate the resistor RCF:
For example, the maximum RCF is 12kfor RSENSE =
1.35m.
CCF provides a low-frequency pole while RCF provides a
midband zero. Place a zero at fZto obtain a phase bump
at the crossover frequency. Place a high-frequency pole
RfL
VR
CF SW
OUT SENSE
×××
×
210
2
GR
CS
=005.
RIR
NG V
FOUT IN
C OUT
=×
××
IV
R
REVERSE CLR
SENSE
=×2
PD R
RSENSE
=×
25 10 3
.
RI
N
SENSE OUT
=0 045.
CIt
V
OUT STEP RESPONSE
Q
=×
ESR V
I
OUT ESR
STEP
=
(20)
(21)
(22)
(23)
(25)
(26)
(27)
(24)
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 29
(fP) at least a decade away from the crossover frequency
to achieve maximum phase margin.
Use the following equations to calculate CCF and CCFF:
PC Board Layout
Use the following guidelines to layout the switching
voltage regulator:
1) Place the VIN and VCC bypass capacitors close to
the MAX5065/MAX5067.
2) Minimize the area and length of the high-current
loops from the input capacitor, upper switching
MOSFET, inductor, and output capacitor back to
the input capacitor negative terminal.
3) Keep short the current loop from the lower-switch-
ing MOSFET, inductor, and output capacitor.
4) Place the Schottky diodes close to the lower
MOSFETs and on the same side of the PC board.
5) Keep the SGND and PGND isolated and connect
them at one single point close to the negative termi-
nal of the input-filter capacitor.
6) Run the current-sense lines CS+ and CS- very
close to each other to minimize the loop area.
Similarly, run the remote-voltage sense lines
SENSE+ and SENSE- close to each other. Do not
cross these critical signal lines through power cir-
cuitry. Sense the current right at the pads of the
current-sense resistors.
7) Avoid long traces between the VCC bypass capaci-
tors, driver output of the MAX5065/MAX5067,
MOSFET gates and PGND pin. Minimize the loop
formed by the VCC bypass capacitors, bootstrap
diode, bootstrap capacitor, MAX5065/MAX5067,
and upper MOSFET gate.
8) Place the bank of output capacitors close to the load.
9) Distribute the power components evenly across the
board for proper heat dissipation.
10) Provide enough copper area at and around the
switching MOSFETs, inductor, and sense resistors
to aid in thermal dissipation.
11) Use at least 4oz copper to keep the trace induc-
tance and resistance to a minimum. Thin copper PC
boards can compromise efficiency since high cur-
rents are involved in the application. Also, thicker
copper conducts heat more effectively, thereby
reducing thermal impedance.
Chip Information
TRANSISTOR COUNT: 5451
PROCESS: BiCMOS
CfR
CFF PCF
=×× ×
1
2π
CfR
CF ZCF
=×× ×
1
2π
(28)
(29)
Selector Guide
PART OUTPUT
MAX5065 Adjustable +0.6V to +3.3V
MAX5067 Adjustable +0.8V to +3.3V with OVP, PGOOD,
Phase Failure Detector
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
Pin Configurations
28 SSOP
TOP VIEW
MAX5065
1
2
3
CSP2
CSN2
PHASE
4
VCC
5
6
7
CLP2
SGND
CLP1
28
27
26
CLKIN
CLKOUT
BST2
25 DH2
24
23
22
LX2
DL2
PGND
8
9
10
SENSE+
SENSE-
DIFF
11
EAN
12
13
14
EAOUT
CSP1
CSN1
21
20
19
IN
DL1
18 LX1
17
16
15
DH1
BST1
EN
PLLCMP N.C.
N.C.
SGND
OVPIN
N.C.
CLP1
OVPOUT
EAN
N.C.
EAOUT
DH1*
PGOOD
VCC
SENSE+
SENSE-
*CONNECT THE THIN QFN EXPOSED PAD TO SGND GROUND PLANE.
BST1
LX1
VDD
DL1
PGND
LX2
DL2
IN
DH2
N.C.
CLP2
BST2
N.C.
DIFF
N.C.
1
2
3
4
5
6
7
8
9
10
11
14 15 16 17 18 19 20 21 2212 13
CSP1
CSN1
N.C.
EN
SGND
N.C.
33
32
31
30
29
28
27
26
25
24
23
44 43 42 41 40 39 38 37 36 35 34
PLLCMP
CSP2
CLKOUT
PHASE
CSN2
CLKIN
N.C.
SGND
44 THIN QFN*
MAX5067
30 _____________________________________________________________________________________
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
______________________________________________________________________________________ 31
SSOP.EPS
PACKAGE OUTLINE, SSOP, 5.3 MM
1
1
21-0056 C
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
NOTES:
1. D&E DO NOT INCLUDE MOLD FLASH.
2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED .15 MM (.006").
3. CONTROLLING DIMENSION: MILLIMETERS.
4. MEETS JEDEC MO150.
5. LEADS TO BE COPLANAR WITHIN 0.10 MM.
7.90
H
L
0∞
0.301
0.025
8∞
0.311
0.037
0∞
7.65
0.63
8∞
0.95
MAX
5.38
MILLIMETERS
B
C
D
E
e
A1
DIM
A
SEE VARIATIONS
0.0256 BSC
0.010
0.004
0.205
0.002
0.015
0.008
0.212
0.008
INCHES
MIN MAX
0.078
0.65 BSC
0.25
0.09
5.20
0.05
0.38
0.20
0.21
MIN
1.73 1.99
MILLIMETERS
6.07
6.07
10.07
8.07
7.07
INCHES
D
D
D
D
D
0.239
0.239
0.397
0.317
0.278
MIN
0.249
0.249
0.407
0.328
0.289
MAX MIN
6.33
6.33
10.33
8.33
7.33
14L
16L
28L
24L
20L
MAX N
A
D
eA1 L
C
HE
N
12
B
0.068
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
32, 44, 48L QFN.EPS
PROPRIETARY INFORMATION
APPROVAL
TITLE:
DOCUMENT CONTROL NO.
21-0144
PACKAGE OUTLINE
32, 44, 48L THIN QFN, 7x7x0.8 mm
1
C
REV.
2
e
L
e
L
A1 A
A2
E/2
E
D/2
D
DETAIL A
D2/2
D2
b
L
k
E2/2
E2
(NE-1) X e
(ND-1) X e
e
C
L
C
L
C
L
C
L
k
DALLAS
SEMICONDUCTOR
PROPRIETARY INFORMATION
DOCUMENT CONTROL NO.APPROVAL
TITLE:
C
REV.
2
2
21-0144
PACKAGE OUTLINE
32, 44, 48L THIN QFN, 7x7x0.8 mm
DALLAS
SEMICONDUCTOR
MAX5065/MAX5067
Dual-Phase, +0.6V to +3.3V Output Parallelable,
Average-Current-Mode Controllers
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
32 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.