5962-0520902KXC - Aeroflex Incorporated

SCD8505 Rev D

FEATURES

❑Radiation Performance

- Radiation 300K(Si) Total Dose

- No Latch-Up or SEE to 120MeV/cm2/mg

❑Full Military Temperature Range

❑Low Power Consumption < 75mW, Typically 50mW

❑64 Channels Provided by Four (4) HS-1840RH Multiplexers

❑Address Bus (A0-3), and Four Enable lines afford flexible organization

❑Output Monitoring of HS-1840RH outputs to a Fifth HS1840RH. Controlled with C0, C1 Address Lines

❑Fast Access Time 1500ns

❑±35V Input Over Voltage Protection (Power On or Off)

❑Break-Before-Make Switching

❑High Analog Input Impedance (with Power On or Off)

❑No Latch-Up

❑Designed for commercial, industrial and aerospace applications

❑Same Form / Fit / Function as ACT8504 but no input Transorbs

❑Packaging – Hermetic Ceramic Quad Flat Pack

- 96 Leads, 1.32"Sq x .20"Ht Quad Flat Pack

- Typical Weight 15 grams

❑DSCC SMD 5962-0520902*

NOTE: Aeroflex Plainview does not currently have a DSCC Certified Radiation Hardened Assurance Program

GENERAL DESCRIPTION

Aeroflex’s ACT8505 is a radiation tolerant, 64 channel multiplexer MCM (multi-chip module) with ESD protection for use in space

applications. It is designed to provide a high input impedance with power on or off.

The ACT8505 has been specifically designed to meet exposure to radiation environments. It is available in a 96 lead High

Temperature Co-Fired Ceramic (HTCC) Quad Flatpack (QFP). The module is guaranteed operational from -55°C to +125°C and

is ideal for demanding military and space applications.

ORGANIZATION AND APPLICATION

The ACT8505 consists of four 16 channel multiplexers arranged as shown in the Block Diagram. The Multiplexer channels 0-63

are controlled by address lines A0-A

3. The mux output monitor is controlled by address lines C0 and C1.

ACT8505 64-Channel Analog Multiplexer Module

Radiation Tolerant

September 29, 2008

www.aeroflex.com/RADHARD

Standard Products

With MUX Output Monitor Function

* Not approved for RAD Hard Version of SMD at this time

Radiation information available upon request

SCD8505 Rev D 9/29/08 Aeroflex Plainview

ACT8505 64 Channel Analog MUX Block Diagram

CH 0

CH 15

•

EN 0-15

OUTPUT 0-15

+VCC

-VEE

VREF

GND

CH 16

CH 31

•

EN 16-31

OUTPUT 16-31

OUTPUT MONITOR

MUX

CH 32

CH 47

•

EN 32-47

16 CH 48

CH 63

•

EN 48-63

OUTPUT 48-63

MUX 4MUX 3

MUX 2 OUTPUT

MONITOR

MUX 1

OUTPUT 32-47

EN 32-47

SCD8505 Rev D 9/29/08 Aeroflex Plainview

ABSOLUTE MAXIMUM RATINGS 1/

Parameter Range Units

Case Operating Temperature Range -55 to +125 °C

Storage Temperature Range -55 to +150 °C

Supply Voltage

+VCC (Pin 44)

-V

EE (Pin 46)

VREF (Pin 48)

+20

-20

+20

Digital Input Overvoltage

VEN (Pins 5, 6, 91, 92), VA (Pins 93, 95, 1, 3), Vc (Pins 2, 4) < VR +4

> GND -4

Analog Input Over Voltage

VS ±18 V

Notes:

1/ All measurements are made with respect to ground.

NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating

only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions"

may effect device reliability.

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Typical Units

+VCC +15V Power Supply Voltage +15.0 V

-VEE -15V Power Supply Voltage -15.0 V

VREF Reference Voltage +5.00 V

AL Logic Low Level +0.8 V

VAH Logic High Level +4.0 V

DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/

(Tc = -55°C to +125°C, +VEE = +15V, -VEE = -15V, VREF = +5.0V, Unless otherwise specified)

Parameter Symbol Conditions Min Max Units

Supply Current I+ VEN(0-63) = VA(0-3)A = VC(0-1)C = 0 .25 2.5 mA

I- VEN(0-63) = VA(0-3)A = VA(0-1)C = 0 -2.5 -.25 mA

+ISBY VEN(0-63) = 4V, VA(0-3)A = VA(0-1)C = 0 6/.25 2.5 mA

-ISBY VEN(0-63) = 4V, VA(0-3)A = VA(0-1)C = 0 6/-2.5 -.25 mA

Address Input Current IAL(0-3)AVA = 0V 1/-4 4 μA

IAH(0-3)AVA = 5V 1/-4 4 μA

IAL(0-1)CVA = 0V 1/-1 1 μA

IAH(0-1)CVA = 5V 1/-1 1 μA

Enable Input Current IENL(0-15) VEN(0-15) = 0V -1 1 μA

IENH(0-15) VEN(0-15) = 5V -1 1 μA

IENL(16-31) VEN(16-31) = 0V -1 1 μA

IENH(16-31) VEN(16-31) = 5V -1 1 μA

IENL(32-47),(MUXMON)VEN(32-47), VEN(MUXMON) = 0V -2 2 μA

IENH(32-47),(MUXMON)VEN(32-47), VEN(MUXMON) = 5V -2 2 μA

IENL(48-63) VEN(48-63) = 0V -1 1 μA

IENH(48-63) VEN(48-63) = 5V -1 1 μA

SCD8505 Rev D 9/29/08 Aeroflex Plainview

Positive Input

Leakage Current

CH0-CH63

+ISOFFOUTPUT(ALL)VIN = +10V, VEN = 4V, output and all unused

MUX inputs under test = -10V 2/, 3/

-100 +200 nA

+ISOFFCURRENT(ALL)-100 +200 nA

Negative Input Leakage

Current CH0-CH63

-ISOFFOUTPUT(ALL)VIN = -10V, VEN = 4V, output and all unused

MUX inputs under test = +10V 2/, 3/

-100 +200 nA

-ISOFFCURRENT(ALL)-100 +200 nA

Output Leakage

Current OUTPUTS

(pins 25, 26, 68 & 70)

Mux Monitor

(pin 69) 6/

+IDOFFOUTPUT(ALL)

VOUT = +10V, VEN = 4V, output and all

unused MUX inputs under test = -10V 3/, 4/

-100 +100 nA

+IDOFFCURRENT(ALL)-100 +100 nA

Output Leakage

Current OUTPUTS

(pins 25, 26, 68 & 70)

Mux Monitor

(pin 69) 6/

-IDOFFOUTPUT(ALL)

VOUT = -10V, VEN = 4V, output and all

unused MUX inputs under test = +10V 3/, 4/

-100 +100 nA

-IDOFFCURRENT(ALL)-100 +100 nA

Switch ON Resistance

OUTPUTS

(pins 25, 26, 68 & 70)

RDS(ON)(0-63)AVIN = +15V, VEN = 0.8V, IOUT = -1mA

2/, 3/, 5/ 500 3000 Ω

RDS(ON)(0-63)B

VIN = +5V, VEN = 0.8V, IOUT = -1mA

2/, 3/, 5/500 3000 Ω

RDS(ON)(0-63)C

VIN = -5V, VEN = 0.8V, IOUT = +1mA

2/, 3/, 5/500 3000 Ω

Switch ON Resistance

Mux Monitor Only

(pin 69) 6/

RDS(ON)(32-63)A

VIN = +15V, VEN = 0.8V, IOUT = -1mA

2/, 3/, 5/ 500 3000 Ω

Notes:

1/ Measure inputs sequentially. Ground all unused inputs of the MUX under test. VA is the applied input voltage to the MUXes’ address lines A(0-3).

2/ VIN is the applied input voltage to the MUXes’ input channel CH0-CH63.

3/ VEN is the applied input voltage to the MUXes’ enable line En(0-15), En(16-31), En(32-47) and En(48-63).

4/ VOUT is the applied input voltage to the MUXes’ output line OUTPUT(1-15), OUTPUT(16-31), OUTPUT(32-47) and OUTPUT(48-63).

5/ Negative current is the current flowing out of each of the MUX pins. Positive current is the current flowing into each MUX pin.

6/ If not tested, shall be guaranteed to the specified limits.

SWITCHING CHARACTERISTICS

(Tc = -55°C to +125°C, +VEE = +15V, -VEE = -15V, VREF = +5.0V, Unless otherwise specified)

Parameter Symbol Conditions Min Max Units

Switching Test MUX tONARL = 10KΩ, CL = 50pF 10 1500 ns

tOFFA

RL = 10KΩ, CL = 50pF

Tc = +25°C, +125°C

Tc = -55°C

2000

5000

tONEN RL = 1KΩ, CL = 50pF

10 1500 ns

tOFFEN 10 1000 ns

DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (con’t)

(Tc = -55°C to +125°C, +VEE = +15V, -VEE = -15V, VREF = +5.0V, Unless otherwise specified)

Parameter Symbol Conditions Min Max Units

SCD8505 Rev D 9/29/08 Aeroflex Plainview

TRUTH TABLE (CH0 – CH15)

A3 A2 A1 A0 EN(0-15) "ON" CHANNEL 1/

XXXXH NONE

LLLLL CH0

LLLHL CH1

LLHLL CH2

LLHHL CH3

LHLLL CH4

LHLHL CH5

LHHLL CH6

LHHHL CH7

HLLLL CH8

HLLHL CH9

HLHLL CH10

HLHHL CH11

HHL L L CH12

HHLHL CH13

HHHL L CH14

HHHHL CH15

1/ Between CH0-15 and OUTPUT (0-15)

TRUTH TABLE (CH16 – CH31)

A3 A2 A1 A0 EN(16-31) "ON" CHANNEL 1/

XXXXH NONE

LLLLL CH16

LLLHL CH17

LLHLL CH18

LLHHL CH19

LHLLL CH20

LHLHL CH21

LHHLL CH22

LHHHL CH23

HLLLL CH24

HLLHL CH25

HLHLL CH26

HLHHL CH27

HHLLL CH28

HHLHL CH29

HHHLL CH30

HHHHL CH31

1/ Between CH16-31 and OUTPUT (16-31)

SCD8505 Rev D 9/29/08 Aeroflex Plainview

TRUTH TABLE (CH32 – CH47)

A3 A2 A1 A0 EN(32-47) "ON" CHANNEL 1/

XXXXH NONE

LLLLL CH32

LLLHL CH33

LLHLL CH34

LLHHL CH35

LHLLL CH36

LHLHL CH37

LHHLL CH38

LHHHL CH39

HLLLL CH40

HLLHL CH41

HLHLL CH42

HLHHL CH43

HHLLL CH44

HHLHL CH45

HHHLL CH46

HHHHL CH47

1/ Between CH32-47 and OUTPUT (32-47)

TRUTH TABLE (CH48 – CH63)

A3 A2 A1 A0 EN(47-63) "ON" CHANNEL 1/

XXXXH NONE

LLLLL CH48

LLLHL CH49

LLHLL CH50

LLHHL CH51

LHLLL CH52

LHLHL CH53

LHHLL CH54

LHHHL CH55

HLLLL CH56

HLLHL CH57

HLHLL CH58

HLHHL CH59

HHLLL CH60

HHLHL CH61

HHHLL CH62

HHHHL CH63

1/ Between CH48-63 and OUTPUT (48-63)

SCD8505 Rev D 9/29/08 Aeroflex Plainview

TRUTH TABLE (MUX OUTPUT MONITOR)

C1 C0 EN(32-47) "ON" CHANNEL

XXH NONE

L L L Output Channels 0-15

L H L Output Channels 16-31

H L L Output Channels 32-47

H H L Output Channels 48-63

SCD8505 Rev D 9/29/08 Aeroflex Plainview

ACT8505 SWITCHING DIAGRAMS

4.0V

50%

~15V

50%

OFF

Enable t

and t

OFF

0.8V

OUT

50%

4.0V

0.8V

OUT

OFFA

Address t

OFFA

50%

12V MIN

0.8V

4.0V

Address t

ON A

OUT

ON A

50%

NOTE: f = 10KHz, Duty cycle = 50%.

SCD8505 Rev D 9/29/08 Aeroflex Plainview

LEAD NUMBERS & FUNCTIONS

ACT8505 – 96 Leads Ceramic QUAD Flat Pack

Pin # Function Pin # Function Pin # Function

233 CH11 65 CH49

034 CH27 66 CH48

335 CH12 67 NC

136 CH28 68 Output V(48-63)

5EN

0-15 37 CH13 69 Mux Output Monitor

6EN

16-31 38 CH29 70 Output V(32-47)

7 CH0 39 CH14 71 GND

8 CH16 40 CH30 72 GND

9 CH1 41 CH15 73 CH47

10 CH17 42 CH31 74 CH46

11CH2 43NC 75CH45

12 CH18 44 +VCC 76 CH44

13CH3 45NC 77CH43

14 CH19 46 -VEE 78 CH42

15CH4 47NC 79CH41

16 CH20 48 VREF 80 CH40

17CH5 49NC 81CH39

18 CH21 50 CASE GND 82 CH38

19CH6 51CH63 83CH37

20 CH22 52 CH62 84 CH36

21CH7 53CH61 85CH35

22 CH23 54 CH60 86 CH34

23 GND 55 CH59 87 CH33

24 GND 56 CH58 88 CH32

25 Output V(0-15) 57 CH57 89 GND

26 Output V(16-31) 58 CH56 90 GND

27CH8 59CH55 91EN

48-63

28 CH24 60 CH54 92 EN 32-47

29CH9 61CH53 93A

30 CH25 62 CH52 94 NC

31 CH10 63 CH51 95 A1

32 CH26 64 CH50 96 NC

NOTE: It is recommended that all "NC or "no connect pin", be grounded. This eliminates or minimizes any ESD or

static buildup.

PLAINVIEW, NEW YORK

Toll Free: 800-THE-1553

Fax: 516-694-6715

SE AND MID-ATLANTIC

Tel: 321-951-4164

Fax: 321-951-4254

INTERNATIONAL

Tel: 805-778-9229

Fax: 805-778-1980

WEST COAST

Tel: 949-362-2260

Fax: 949-362-2266

NORTHEAST

Tel: 603-888-3975

Fax: 603-888-4585

CENTRAL

Tel: 719-594-8017

Fax: 719-594-8468

www.aeroflex.com info-ams@aeroflex.com

Our passion for perform an ce is de fined by thre e

attributes represented by these three icons:

solution-minded, perform an ce-d riven an d customer-focused

Aeroflex Microelectronic Solutions reserves the right to

change at any time without notice the specifications, design,

function, or form of its products described herein. All

parameters must be validated for each customer's application

by engineering. No liability is assumed as a result of use of

this product. No patent licenses are implied.

SCD8505 Rev D 9/29/08

EXPORT CONTROL: EXPOR T WARNING:

This product is controlled for export under the International Traffic in

Arms Regulations (ITAR). A license from the U.S. Department of

State is required prior to the export of this product from the United

States.

Aeroflex’s military and space products are controlled for export under

the International Traffic in Arms Regulations (ITAR) and may not be

sold or proposed or offered for sale to certain countries. (See ITAR

126.1 for complete information.)

1.320 SQ

Pin 85

Pin 12

Pin 60Pin 37

Pin 13

Pin 36

Pin 61

Pin 84

Pin 1

FLAT PACKAGE OUTLINE

MAX

.0165

±.003

.200

MAX

.400

Note: Outside ceramic tie bars

not shown for clarity. Contact

factory for details.

.006

±.001

(23 Spaces at .050)

Tol Non-Cum

4 Sides

1.150 ±.005

ORDERING INFORMATION

Model Number Screening DESC SMD # Package

ACT8505-S Military Temperature, -55°C to +125°C,

Compliant to MIL-PRF-38534 Class K

NA QUAD Flat Pack

ACT8505-7 Commercial Flow, +25°C testing only

ACT8505-201-1S Military Temperature, -55°C to +125°C,

Compliant to MIL-PRF-38534 Class K

5962-0520902KXC