CAT.8100S
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
4 6.3 10 16 20 25 35
0G 0J 1A 1C 1D 1E 1V
1105 P P •SS
•A
1.5 155 PSSA
2.2 225 P P •SS
•AA
•B
3.3 335 P P A A (A) •B
4.7 475 P P A (S) • A •BB
6.8 685 P S A •B
10 106 P P P •S •AA
•BB
15 156 P P P •S •A (S) • A •B
22 226 P P •S (P) •S •AA
•BB
33 336 P •SP
•S •AS
•AB
47 476 P •S •A (P) •S •A (S) • A •B (B)
68 686 S •AS
•A •BB
100 107 S •A •B (S) • A •B (B)
150 157 B
220 227 (A) •B (B)
V
•After 1 minute's application of rated voltage, leakage current at 20
˚C
is not
more than 0.01CV or 0.5 µA, whichever is greater.
•After 1 minute's application of rated voltage, leakage current at 85
˚C
is not
more than 0.1CV or 5 µA, whichever is greater.
•After 1 minute's application of derated voltage, leakage current at 125
˚C
is
not more than 0.125CV or 6.3 µA, whichever is greater.
Dipping Flow at 260
˚C
for 10 seconds, reflow at 260
˚C
for 10 seconds
+15% Max. (at +125
˚C
)
+10% Max. (at +85
˚C
)
--10% Max. (at --55
˚C
)
Damp Heat
Temperature Cycles
At 40
˚C
, 90 ~ 95% R.H., For 500 hours (No voltage applied)
Capacitance Change •••••• Within ±10% of initial value
Dissipation Factor •••••••••• Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
At --55
˚C
/ +125
˚C
, 30 minutes each, For 5 cycles,
Capacitance Change •••••• Within ±5% of initial value
Dissipation Factor •••••••••• Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
Resistance to
Soldering Heat Capacitance Change •••••• Within ±5% of initial value
Dissipation Factor •••••••••• Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
Endurance∗
After 2000 hours' application of rated voltage at 85
˚C
, or derated voltage at
125
˚C
, capacitors meet the characteristic requirements listed below.
Capacitance Change •••••• Within ±10% of initial value
Dissipation Factor •••••••••• Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
Surge∗
After application of surge voltage in series with a 33
Ω
resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85
˚C
,
capacitors meet the characteristics requirements listed below.
Capacitance Change •••••• Within ±5% of initial value
Dissipation Factor •••••••••• Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
Shear Test
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
a specified jig at the center of the
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
abnormality on the capacitor terminals.
5N (0.51kg • f)
For 10 ± 1 seconds
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F95
Conformal coated
Chip
Specifications
Type numbering system (Example : 35V 1.5 µF)
Drawing
L W
H
Solder Solder
ABC(D)
Resin
Single-side electrodes
(Both electrodes at bottom side only)
Item
Category
Temperature Range
Capacitance Tolerance
Dissipation Factor
(at 120Hz)
Leakage Current
Capacitance Change
by Temperature
Performance Characteristics
--55 ~ +125
˚C
(Rated temperature : 85
˚C
)
±20%, ±10% (at 120Hz)
Case Code
D dimension only for reference
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
Dimensions
Refer to P.221
R230
45 45
20
1
mm
∗As for the surge and derated voltage at 125
˚C
, refer to page 212 for details.
Standard ratings
(mm)
Cap.
(µF) Code
Refer to P.221E.S.R.(100kHz)
L
2.2 ± 0.3 1.25 ± 0.3 0.9 ± 0.3 0.6 ± 0.3 0.8 ± 0.3 0.8 ± 0.3
W H A B C (D)
(0.2)
P3.2 ± 0.3 1.6 ± 0.3 0.9 ± 0.3 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3 (0.2)
S1.3 ± 0.3
1.7 ± 0.3 0.8 ± 0.3
0.8 ± 0.3 1.2 ± 0.3
1.2 ± 0.3 0.8 ± 0.3
1.1 ± 0.3
1.7 ± 0.3
2.7 ± 0.3
3.2 ± 0.3
3.3 ± 0.3 (0.2)
(0.2)
A
B
Taping code
(Refer to page 213 for details)
Single face electrode
F
19
25
31
4V
51
65
75
8M
9A
10 11 A
12 Q
13 2
14
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
CAT.8100S
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F95
Standard ratings
15 P F950G156MPAAQ2 0.6 10 1.8
22 P F950G226MPAAQ2 0.9 14 1.1
33 P F950G336MPAAQ2 1.3 14 1.1
33 S F950G336MSAAQ2 1.3 8 1.0
47 P F950G476MPAAQ2 1.9 14 1.1
47 S F950G476MSAAQ2 1.9 10 0.8
47 A F950G476MAAAQ2 1.9 8 0.6
68 S F950G686MSAAQ2 2.7 10 0.8
68 A F950G686MAAAQ2 2.7 10 0.5
100 S F950G107MSAAQ2 4.0 14 0.8
100 A F950G107MAAAQ2 4.0 12 0.5
100 B F950G107MBAAQ2 4.0 10 0.4
150 B F950G157MBAAQ2 6.0 14 0.4
10 P F950J106MPAAQ2 0.6 8 2.0
15 P F950J156MPAAQ2 0.9 10 1.8
22 P F950J226MPAAQ2 1.4 14 1.1
22 S F950J226MSAAQ2 1.4 10 1.0
33 P F950J336MPAAQ2 2.1 14 1.1
33 S F950J336MSAAQ2 2.1 10 1.0
33 A F950J336MAAAQ2 2.1 8 0.8
47 S F950J476MSAAQ2 3.0 10 0.9
47 A F950J476MAAAQ2 3.0 10 0.6
68 S F950J686MSAAQ2 4.3 14 0.9
68 A F950J686MAAAQ2 4.3 12 0.5
68 B F950J686MBAAQ2 4.3 8 0.4
100 A F950J107MAAAQ2 6.3 14 0.5
100 B F950J107MBAAQ2 6.3 14 0.4
3.3 P F951A335MPAAQ2 0.5 8 5.0
4.7 P F951A475MPAAQ2 0.5 8 4.0
6.8 P F951A685MPAAQ2 0.7 8 4.0
10 P F951A106MPAAQ2 1.0 8 3.0
15 P F951A156MPAAQ2 1.5 10 3.0
15 S F951A156MSAAQ2 1.5 8 1.2
15 A F951A156MAAAQ2 1.5 6 1.0
22 S F951A226MSAAQ2 2.2 10 1.1
22 A F951A226MAAAQ2 2.2 6 0.9
33 S F951A336MSAAQ2 3.3 10 1.1
33 A F951A336MAAAQ2 3.3 10 0.8
47 A F951A476MAAAQ2 4.7 10 0.8
47 B F951A476MBAAQ2 4.7 8 0.4
68 B F951A686MBAAQ2 6.8 12 0.4
1 P F951C105MPAAQ2 0.5 8 8.0
1.5 P F951C155MPAAQ2 0.5 8 8.0
2.2 P F951C225MPAAQ2 0.5 8 6.0
3.3 P F951C335MPAAQ2 0.5 8 6.0
4.7 P F951C475MPAAQ2 0.8 10 4.0
6.8 S F951C685MSAAQ2 1.1 6 2.5
10 P F951C106MPAAQ2 1.6 10 4.0
10 S F951C106MSAAQ2 1.6 8 2.0
10 A F951C106MAAAQ2 1.6 6 1.4
15 A F951C156MAAAQ2 2.4 8 1.4
15 B F951C156MBAAQ2 2.4 6 0.7
22 A F951C226MAAAQ2 3.5 8 1.4
22 B F951C226MBAAQ2 3.5 6 0.5
33 B F951C336MBAAQ2 5.3 8 0.5
4V
6.3V
10V
16V
Part Number
Leakage
Current
(
µ
A)
Disspation
Factor
(%@120Hz)
Case
size E.S.R
(
Ω
@100kHZ)
Rated Volt
(V)
Rated
Capacitance
(
µ
F)
1.5 S F951D155MSAAQ2 0.5 6 6.0
2.2 P F951D225MPAAQ2 0.5 8 6.0
2.2 S F951D225MSAAQ2 0.5 6 5.0
3.3 A F951D335MAAAQ2 0.7 6 2.0
4.7 A F951D475MAAAQ2 0.9 6 1.5
6.8 A F951D685MAAAQ2 1.4 8 1.5
6.8 B F951D685MBAAQ2 1.4 6 0.9
10 A F951D106MAAAQ2 2.0 8 1.5
10 B F951D106MBAAQ2 2.0 6 0.8
22 B F951D226MBAAQ2 4.4 8 0.8
1 P F951E105MPAAQ2 0.5 6 8.0
1 S F951E105MSAAQ2 0.5 6 8.0
1.5 S F951E155MSAAQ2 0.5 6 7.0
2.2 S F951E225MSAAQ2 0.6 6 7.0
2.2 A F951E225MAAAQ2 0.6 6 3.2
3.3 A F951E335MAAAQ2 0.8 6 2.8
4.7 A F951E475MAAAQ2 1.2 8 2.0
4.7 B F951E475MBAAQ2 1.2 6 0.9
10 B F951E106MBAAQ2 2.5 6 0.9
1 S F951V105MSAAQ2 0.5 6 8.0
1 A F951V105MAAAQ2 0.5 4 4.4
1.5 A F951V155MAAAQ2 0.5 6 4.4
2.2 A F951V225MAAAQ2 0.8 6 4.4
2.2 B F951V225MBAAQ2 0.8 6 1.6
3.3 B F951V335MBAAQ2 1.2 6 1.6
4.7 B F951V475MBAAQ2 1.7 6 1.6
20V
25V
35V
Part Number
Leakage
Current
(
µ
A)
Disspation
Factor
(%@120Hz)
Case
size E.S.R
(
Ω
@100kHZ)
Rated Volt
(V)
Rated
Capacitance
(
µ
F)
In case of capacitance tolerance ±10% type, K will be put at 9th digit of type
numbering system.
