SIP20C Series Single output DC/DC CONVERTERS * * * * * * * * * 9-20W Non-isolated DC/DC Regulators 1 Updated version of SIP20 Best-of-class wide output trim range Industry standard footprint High power density (60W/in3) High Efficiency 90% Fixed frequency (500kHz) Remote ON/OFF Undervoltage lockout (UVLO) Remote sense option The SIP20C series are non-isolated DC/DC converters packaged in a single-in-line footprint (2.5 x 0.55 x 0.23 inches) giving designers a cost effective solution for conversion of 5VDC to 3.3VDC and lower voltages. The SIP20C offers a best-of-class wide output trim range which allows maximum design flexibility and a pathway for future upgrades. Local voltage conversion by the SIP20C from existing 5V system voltages eliminates the need for redesign of existing power architectures when voltage requirements change. The SIP20C is designed for applications that include distributed power, workstations, computers and file servers. Implementing state of the art surface mount technology and automated manufacturing techniques, the SIP20C offers compact size and efficiencies of 90%. The SIP20C is an updated version of the original SIP20 and is fully compatible with the original model. 2 YEAR WARRANTY SPECIFICATIONS All specifications are typical at nominal input, full load at 25C unless otherwise stated OUTPUT SPECIFICATIONS EMC CHARACTERISTICS Voltage adjustability S3V3 S2V5 S1V5 Set point accuracy (See Note 1) 2.7% Line regulation Vin = 4.5V to 5.5V 0.3% Load regulation Io = 0A to 6A 0.3% Minimum load 0A Overshoot/undershoot Ripple and noise (See Note 8) None 0 to 20MHz BW Temperature coefficient 100mV pk-pk, 30mV rms max. Radiated emissions Electrostatic discharge EN55022/11, FCC part 15 EN61000-4-2, IEC801-2 (See Note 6) Level A GENERAL SPECIFICATIONS Efficiency See table Isolation voltage Switching frequency Non-isolated Fixed Approvals and standards (See Note 7) 500kHz typ. VDE0805, EN60950, IEC950 UL1950, CSA C22.2 No. 950 Material flammability Dimensions UL94V-0 (LxWxH) 63.5 x 13.97 x 5.84 mm 2.5 x 0.55 x 0.23 inches 0.01%/C Transient response (See Note 2) Remote sense 60% to 115% 60% to 110% 87% to 130% (4) 2.0% max. deviation 300s recovery to within 1.0% Pin length 0.5VDC compensation MTBF 0.135 0.02 inches (3.43 0.5mm) Weight 5g (0.18oz) MIL-HDBK-217F >1,000,000 hours ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Thermal performance Input voltage range Input current No load Input current @ Io max. and Vin = 0 to 5.5V Input reflected ripple (See Note 3) Remote ON/OFF -25C to +85C See Curve -55C to +100C Altitude Operating Non-operating 10,000 feet max. 40,000 feet max. Vibration 5Hz to 500Hz 150mA 5.3A max. 200mA (See Note 5) Start-up time External capacitor Operating ambient, convection cooled Operating ambient, 300LFM forced air Non-operating 4.5 to 5.5VDC (See Note 4) 1.0ms International Safety Standard Approvals 100F VDE0805/EN60950/IEC950 pending See curve 2.4G rms (approx.) UL1950 CSA 22.2 No. 950 pending File Name: SIP20C.PDF Rev: 05 Feb 2003 SIP20C Series Single output DC/DC CONVERTERS 9-20W Non-isolated DC/DC Regulators 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT POWER (MAX.) INPUT VOLTAGE OUTPUT VOLTAGE OUTPUT CURRENT (MIN.) OUTPUT CURRENT (MAX.) EFFICIENCY (TYP.) LINE LOAD MODEL NUMBER (6) 20W 4.5-5.5VDC 3.3V 0A 6A 90% 0.3% 0.3% SIP20C-05S3V3 15W 4.5-5.5VDC 2.5V 0A 6A 82% 0.3% 0.3% SIP20C-05S2V5 9W 4.5-5.5VDC 1.5V 0A 6A 75% 0.3% 0.3% SIP20C-05S1V5 Notes 2 3 4 5 6 7 8 9 PROTECTION Vin = 5.0V, Io = full load, TA = 25C. Total error band 4.5% over all operating conditions and temperatures until end of life. di/dt = 1A/1s, Vin = 5VDC, Tc = 25C, load change = 0.5 lo max. to lo max. and Io max. to 0.5 Io max. With simulated source impedance of 500nH. 5Hz to 20MHz. Use a 100F with ESR = 0.045 max. at 100kHz @ 25C. Referenced to ground for shutdown. If pin 6 is high unit will shut down. If pin 6 is open unit will operate as normal. Single line sense; 0.5VDC compensation. Designate with the suffix 'R' e.g. SIP20C-05S3V3R. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 0-20MHz BW, 0.1F ceramic, 1F tantalum on output. A short from +Vout to ground of less than 100m may cause the unit to enter a non-destructive latch-up mode. If latch-up does occur the power supply to the unit may need to be cycled. Short circuit protection Continuous (See Note 9) Input surge protection 6VDC continuous max. Undervoltage protection UVLO Vin <3.8V Thermal protection Automatic recovery, unit will shut down if RT1 exceeds 85C (See diagram below) EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using either method shown below. J1 PIN 5 J1 PIN 5 TRIM UP DERATING CURVE 6 J2 PIN 5 300 LFM 5 10KW TRIMPOT J2 PIN 5 TRIM DOWN 200 LFM J1 PIN 2 Output Current (A) 1 REGULATION J1 PIN 2 100 LFM 4 3 NATURAL CONVECTION COOLING 2 J1 PIN CONNECTIONS 1 0 -25 C 0 C 15 C 25 C 35 C 45 C 55 C 65 C 75 C 85 C AMBIENT TEMPERATURE ( C) 2.50 (63.5) 0.23 Max. (5.84) PC Board 0.135 (3.43) 1234 56 J1 J2 0.10 (2.54) Optional Remote Sense Pin (See Note 6) 0.28 (7.11) 1 +Vout 2 +Vout 3 Opt. Remote Sense (+) 4 +Vout 5 Ground J2 PIN CONNECTIONS PIN NUMBER FUNCTION 1 Ground 2 +Vin 3 +Vin 4 No Pin 0.685 (17.40) 1 2 34 5 0.140 Max. (3.556) FUNCTION 0.55 (13.97) RT1 0.025 (0.635) Square Pins PIN NUMBER 1.90 (48.26) ALL DIMENSIONS IN INCHES (mm) Recommended hole size 0.04 (1.0) Plated through hole 5 Trim 6 Remote ON/OFF Data Sheet (c) Artesyn Technologies(R) 2002 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. www.artesyn.com File Name: SIP20C.PDF Rev: 05 Feb 2003