TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com LOW-NOISE, HIGH PSRR, RF 200-mA LOW-DROPOUT LINEAR REGULATORS Check for Samples: TPS730xx FEATURES DESCRIPTION * 200-mA RF Low-Dropout Regulator With Enable * Available in Fixed Voltages from 1.8V to 3.3V and Adjustable (1.22V to 5.5V) * High PSRR (68dB at 100Hz) * Ultralow-Noise (33VRMS, TPS73018) * Fast Start-Up Time (50s) * Stable With a 2.2F Ceramic Capacitor * Excellent Load/Line Transient Response * Very Low Dropout Voltage (120mV at 200mA) * 5- and 6-Pin SOT23 (DBV), and Wafer Chip Scale (YZQ) Packages The TPS730xx family of low-dropout (LDO) low-power linear voltage regulators features high power-supply rejection ratio (PSRR), ultralow-noise, fast start-up, and excellent line and load transient responses a small SOT23 package. NanoStarTM packaging gives an ultrasmall footprint as well as an ultralow profile and package weight, making it ideal for portable applications such as handsets and PDAs. Each device in the family is stable, with a small 2.2F ceramic capacitor on the output. The TPS730xx family uses an advanced, proprietary BiCMOS fabrication process to yield low dropout voltages (e.g., 120mV at 200mA, TPS73030). Each device achieves fast start-up times (approximately 50s with a 0.001F bypass capacitor) while consuming low quiescent current (170A typical). Moreover, when the device is placed in standby mode, the supply current is reduced to less than 1A. The TPS73018 exhibits approximately 33VRMS of output voltage noise at 1.8V output with a 0.01F bypass capacitor. Applications with analog components that are noise-sensitive, such as portable RF electronics, benefit from the high PSRR and low-noise features as well as the fast response time. 1 234 APPLICATIONS * * * * * RF: VCOs, Receivers, ADCs Audio Cellular and Cordless Telephones Bluetooth(R), Wireless LAN Handheld Organizers, PDAs DBV PACKAGE (TOP VIEW) GND 2 EN 3 5 OUT 4 NR Fixed Option DBV PACKAGE (TOP VIEW) IN 1 6 GND 2 5 3 EN OUT FB 4 NR Adjustable Option YZQ PACKAGE (TOP VIEW) IN C3 A3 EN C1 B2 A1 OUT TPS73028 TPS73028 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY RIPPLE REJECTION vs FREQUENCY 0.30 100 VIN = 3.8 V COUT = 2.2 F CNR = 0.1 F 0.25 90 IOUT = 200 mA 80 Ripple Rejection (dB) 1 Output Spectral Noise Density (V/Hz) IN 0.20 0.15 IOUT = 1 mA 0.10 IOUT = 200 mA 70 60 50 40 IOUT = 10 mA 30 20 0.05 VIN = 3.8 V COUT = 10 F CNR = 0.01 F 10 0 0 100 1k 10 k Frequency (Hz) NR 100 k 10 100 1k 10 k 100 k 1M 10 M Frequency (Hz) GND Figure 1. 1 2 3 4 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoStar is a trademark of Texas Instruments. Bluetooth is a registered trademark of Bluetooth Sig, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PRODUCT TPS730xx yy yz (1) VOUT XX is nominal output voltage (for example, 28 = 2.8V, 01 = Adjustable). YYY is package designator. Z is package quantity. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the device product folder at www.ti.com. ABSOLUTE MAXIMUM RATINGS Over operating temperature range (unless otherwise noted). (1) UNIT VIN range -0.3V to +6V VEN range -0.3V to +6V VOUT range -0.3V to VIN + 0.3V Peak output current ESD rating, HBM ESD rating, CDM Continuous total power dissipation Internally limited 2kV 500V See Dissipation Ratings Table Junction temperature range -40C to +150C Storage temperature range, Tstg -65C to +150C (1) 2 Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Submit Documentation Feedback (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com DISSIPATION RATINGS TABLE TA +25C POWER RATING TA = +70C POWER RATING TA = +85C POWER RATING BOARD PACKAGE RJC RJA DERATING FACTOR ABOVE TA = +25C Low-K (1) DBV 65C/W 255C/W 3.9mW/C 390mW 215mW 155mW (2) DBV 65C/W 180C/W 5.6mW/C 560mW 310mW 225mW Low-K (1) YZQ 27C/W 255C/W 3.9mW/C 390mW 215mW 155mW High-K (2) YZQ 27C/W 190C/W 5.3mW/C 530mW 296mW 216mW High-K (1) (2) The JEDEC low-K (1s) board design used to derive this data was a 3-inch x 3-inch, two layer board with 2 ounce copper traces on top of the board. The JEDEC high-K (2s2p) board design used to derive this data was a 3-inch x 3-inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. ELECTRICAL CHARACTERISTICS Over recommended operating temperature range TJ = -40 to +125C, VEN = VIN, VIN = VOUT(nom) + 1 V (1), IOUT = 1mA, COUT = 10F, CNR = 0.01F (unless otherwise noted). Typical values are at +25C. PARAMETER TEST CONDITIONS VIN Input voltage (1) IOUT Continuous output current VFB Internal reference (TPS73001) Line regulation (VOUT%/VIN) V 200 mA 1.225 -2% VOUT(nom) 1.250 V 5.5 - VDO V +2% V 0.05 0A IOUT 200mA, TJ = +25C Dropout voltage (2)(VIN = VOUT(nom) - 0.1V) IOUT = 200mA Output current limit VOUT = 0V GND pin current 0A IOUT 200mA Shutdown current (3) VEN = 0V, 2.7V VIN 5.5V FB pin current VFB = 1.8V TPS73028 UNIT 0 VOUT + 1V VIN 5.5V Load regulation (VOUT%/IOUT) Power-supply ripple rejection MAX 5.5 VFB 0A IOUT 200mA, 2.75V VIN < 5.5V (1) TYP 2.7 1.201 Output voltage range (TPS73001) Output voltage accuracy MIN %/V 5 120 mV 210 mV 600 mA 170 250 A 0.07 1 A 1 A 285 f = 100Hz, TJ = +25C, IOUT = 200mA 68 dB Output noise voltage (TPS73018) BW = 200Hz to 100kHz, IOUT = 200mA CNR = 0.01F 33 VRMS Time, start-up (TPS73018) RL = 14, COUT = 1F CNR = 0.001F 50 s High level enable input voltage 2.7V VIN 5.5V 1.7 VIN Low level enable input voltage 2.7V VIN 5.5V 0 0.7 V EN pin current VEN = 0 -1 1 A UVLO threshold VCC rising UVLO hysteresis (1) (2) (3) 2.25 2.65 100 V V mV Minimum VIN is 2.7V or VOUT + VDO, whichever is greater. Dropout is not measured for the TPS73018 and TPS73025 since minimum VIN = 2.7V. For adjustable versions, this applies only after VIN is applied; then VEN transitions high to low. (c) 2004-2011, Texas Instruments Incorporated Submit Documentation Feedback 3 TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com FUNCTIONAL BLOCK DIAGRAMS ADJUSTABLE VERSION IN OUT UVLO 2.45V 59 k Current Sense ILIM GND R1 SHUTDOWN _ + FB EN R2 UVLO Thermal Shutdown Bandgap Reference 1.22V IN External to the Device QuickStart 250 k Vref NR FIXED VERSION IN OUT UVLO 2.45V Current Sense GND SHUTDOWN ILIM _ R1 + EN UVLO R2 Thermal Shutdown R2 = 40 k QuickStart Bandgap Reference 1.22V IN 250 k Vref NR Table 1. Terminal Functions TERMINAL 4 NAME SOT23 ADJ SOT23 FIXED WCSP FIXED NR 4 4 B2 Connecting an external capacitor to this pin bypasses noise generated by the internal bandgap. This improves power-supply rejection and reduces output noise. EN 3 3 A3 Driving the enable pin (EN) high turns on the regulator. Driving this pin low puts the regulator into shutdown mode. EN can be connected to IN if not used. DESCRIPTION FB 5 N/A N/A This terminal is the feedback input voltage for the adjustable device. GND 2 2 A1 Regulator ground IN 1 1 C3 Input to the device. OUT 6 5 C1 Output of the regulator. Submit Documentation Feedback (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com TYPICAL CHARACTERISTICS (SOT23 PACKAGE) TPS73028 OUTPUT VOLTAGE vs OUTPUT CURRENT TPS73028 OUTPUT VOLTAGE vs JUNCTION TEMPERATURE 2.805 250 2.805 VIN = 3.8 V COUT = 10 F TJ = 25C 2.804 2.803 VIN = 3.8 V COUT = 10 F 2.800 VOUT (V) 2.800 2.799 IGND (A) 2.795 2.801 2.790 IOUT = 200 mA 2.785 2.798 2.797 2.795 0 50 100 150 2.775 200 IOUT = 200 mA 150 100 50 2.780 VIN = 3.8 V COUT = 10 F 2.796 -40 -25 -10 5 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 IOUT (mA) 20 35 50 65 80 95 110 125 TJ (C) TJ (C) Figure 2. Figure 3. Figure 4. TPS73028 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY ROOT MEAN SQUARE OUTPUT NOISE vs CNR TPS73028 DROPOUT VOLTAGE vs JUNCTION TEMPERATURE 1.6 180 60 1.2 CNR = 0.001 F 1.0 CNR = 0.0047 F 0.8 CNR = 0.01 F 0.6 CNR = 0.1 F 0.4 VOUT = 2.8 V IOUT = 200 mA COUT = 10 mF 50 140 40 120 30 20 IOUT = 200 mA 100 80 60 40 10 0.2 0 0.001 IOUT = 10 mA 20 BW = 100 Hz to 100 kHz 0 100 VIN = 2.7 V COUT = 10 F 160 VDO (mV) VIN = 3.8 V IOUT = 200 mA COUT = 10 F 1.4 RMS Output Noise (mVRMS) Output Spectral Noise Density (V/Hz) IOUT = 1 mA 200 IOUT = 1 mA 2.802 VOUT (V) TPS73028 GROUND CURRENT vs JUNCTION TEMPERATURE 0 -40 -25 -10 5 0.01 CNR (mF) Figure 5. Figure 6. Figure 7. TPS73028 RIPPLE REJECTION vs FREQUENCY TPS73028 OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) TPS73028 LINE TRANSIENT RESPONSE 10 k 100 k 0.1 20 35 50 65 80 95 110 125 Frequency (Hz) 1k TJ (C) 90 4 VEN (V) IOUT = 200 mA 70 2 0 60 50 CNR = 0.001 F 30 VIN = 3.8 V COUT = 10 F CNR = 0.01 F 10 0 10 100 1k 4.8 3.8 IOUT = 200 mA COUT = 2.2 F CNR = 0.01 F 20 3 IOUT = 10 mA 20 VIN = 3.8 V VOUT = 2.8 V IOUT = 200 mA COUT = 2.2 F TJ = 25C 2 CNR = 0.0047 F 1 CNR = 0.01 F VIN (mV) 40 VOUT (V) Ripple Rejection (dB) 80 VOUT (mV) 100 dv 0.4 V + s dt 0 -20 0 10 k 100 k 1M 10 M Frequency (Hz) Figure 8. (c) 2004-2011, Texas Instruments Incorporated 0 20 40 60 80 100 120 140 160 180 200 Time (s) Figure 9. 0 10 20 30 40 50 60 70 80 90 100 Time (s) Figure 10. Submit Documentation Feedback 5 TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com TYPICAL CHARACTERISTICS (SOT23 PACKAGE) (continued) TPS73028 LOAD TRANSIENT RESPONSE DROPOUT VOLTAGE vs OUTPUT CURRENT POWER-UP/POWER-DOWN 250 VIN = 3.8 V COUT = 10 F TJ = 125C -20 di 0.02A + s dt 300 VDO (mV) -40 IOUT (mA) 200 0 500 mV/div VOUT (mV) 20 VOUT = 3 V RL = 15 VIN 200 TJ = 25C 100 VOUT 0 TJ = -55C 50 1mA 100 0 150 0 50 100 150 200 250 300 350 400 450 500 0 1s/div 20 40 60 80 100 120 140 160 180 200 IOUT (mA) Time (s) Figure 11. Figure 12. TYPICAL REGIONS OF STABILITY EQUIVALENT SERIES RESISTANCE (ESR) vs OUTPUT CURRENT 100 COUT = 2.2 F VIN = 5.5 V, VOUT 1.5 V TJ = -40C to 125C 10 Region of Instability 1 0.1 Region of Stability 0.01 COUT = 10 F VIN = 5.5 V TJ = -40C to 125C 10 Region of Instability 1 0.1 Region of Stability 0.01 0 6 TYPICAL REGIONS OF STABILITY EQUIVALENT SERIES RESISTANCE (ESR) vs OUTPUT CURRENT ESR, Equivalent Series Resistance () ESR, Equivalent Series Resistance () 100 Figure 13. 0.02 0.04 0.06 0.08 0.20 0 0.02 0.04 0.06 IOUT (A) IOUT (A) Figure 14. Figure 15. Submit Documentation Feedback 0.08 0.20 (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com APPLICATION INFORMATION The TPS730xx family of low-dropout (LDO) regulators has been optimized for use in noise-sensitive battery-operated equipment. The device features extremely low dropout voltages, high PSRR, ultralow output noise, low quiescent current (170A typically), and enable-input to reduce supply currents to less than 1A when the regulator is turned off. A typical application circuit is shown in Figure 16. VIN VOUT VIN IN VOUT OUT TPS730xx 0.1F EN GND NR 2.2F 0.01F(1) NOTE: (1) This capacitor is optional. Figure 16. Typical Application Circuit External Capacitor Requirements A 0.1F or larger ceramic input bypass capacitor, connected between IN and GND and located close to the TPS730xx, is required for stability and improves transient response, noise rejection, and ripple rejection. A higher-value input capacitor may be necessary if large, fast-rise-time load transients are anticipated or the device is located several inches from the power source. Like most low dropout regulators, the TPS730xx requires an output capacitor connected between OUT and GND to stabilize the internal control loop. The minimum recommended capacitance is 2.2F. Any 2.2F or larger ceramic capacitor is suitable, provided the capacitance does not vary significantly over temperature. If load current is not expected to exceed 100mA, a 1.0F ceramic capacitor can be used. The internal voltage reference is a key source of noise in an LDO regulator. The TPS730xx has an NR pin which is connected to the voltage reference through a 250k internal resistor. The 250k internal resistor, in conjunction with an external bypass capacitor connected to the NR pin, creates a low pass filter to reduce the voltage reference noise and, therefore, the noise at the regulator output. In order for the regulator to operate properly, the current flow out of the NR pin must be at a minimum, because any leakage current creates an IR drop across the internal resistor thus creating an output error. Therefore, the bypass capacitor must have minimal leakage current. The bypass capacitor should be no more than 0.1F to ensure that it is fully charged during the quickstart time provided by the internal switch shown in the Functional Block Diagrams. As an example, the TPS73018 exhibits only 33VRMS of output voltage noise using a 0.01F ceramic bypass capacitor and a 2.2F ceramic output capacitor. Note that the output starts up slower as the bypass capacitance increases due to the RC time constant at the NR pin that is created by the internal 250k resistor and external capacitor. Board Layout Recommendation to Improve PSRR and Noise Performance To improve ac measurements like PSRR, output noise, and transient response, it is recommended that the board be designed with separate ground planes for VIN and VOUT, with each ground plane connected only at the GND pin of the device. In addition, the ground connection for the bypass capacitor should connect directly to the GND pin of the device. (c) 2004-2011, Texas Instruments Incorporated Submit Documentation Feedback 7 TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com Power Dissipation and Junction Temperature Specified regulator operation is assured to a junction temperature of +125C; the maximum junction temperature should be restricted to +125C under normal operating conditions. This restriction limits the power dissipation the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or equal to PD(max). The maximum power dissipation limit is determined using Equation 1: T max *T A P D(max) + J R QJA Where: * * * TJmax is the maximum allowable junction temperature. RJA is the thermal resistance junction-to-ambient for the package (see the Dissipation Ratings Table). TA is the ambient temperature. The regulator dissipation is calculated using Equation 2: P D + VIN*V OUT I OUT (1) (2) Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal protection circuit. Programming the TPS73001 Adjustable LDO Regulator The output voltage of the TPS73001 adjustable regulator is programmed using an external resistor divider as shown in Figure 17. The output voltage is calculated using Equation 3: V OUT + VREF 1 ) RR 1 2 Where: * VREF = 1.225V typ (the internal reference voltage) (3) Resistors R1 and R2 should be chosen for approximately 50A divider current. Lower value resistors can be used for improved noise performance, but the solution consumes more power. Higher resistor values should be avoided as leakage current into/out of FB across R1/R2 creates an offset voltage that artificially increases/decreases the feedback voltage and thus erroneously decreases/increases VOUT. The recommended design procedure is to choose R2 = 30.1k to set the divider current at 50A, C1 = 15pF for stability, and then calculate R1 using Equation 4: R1 = VOUT VREF - 1 R2 (4) In order to improve the stability of the adjustable version, it is suggested that a small compensation capacitor be placed between OUT and FB. For voltages < 1.8V, the value of this capacitor should be 100pF. For voltages > 1.8V, the approximate value of this capacitor can be calculated as shown in Equation 5: (3 x 10*7) x (R 1 ) R 2) C1 + (R 1 x R2) (5) The suggested value of this capacitor for several resistor ratios is shown in the table below. If this capacitor is not used (such as in a unity-gain configuration) or if an output voltage < 1.8V is chosen, then the minimum recommended output capacitor is 4.7F instead of 2.2F. 8 Submit Documentation Feedback (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com OUTPUT VOLTAGE PROGRAMMING GUIDE VIN IN 1mF OUT TPS73001 EN NR GND 0.01mF VOUT R1 FB R2 C1 2.2mF OUTPUT VOLTAGE R1 R2 C1 1.22V short open 0pF 2.5V 31.6kW 30.1kW 22pF 3.3V 51kW 30.1kW 15pF 3.6V 59kW 30.1kW 15pF Figure 17. TPS73001 Adjustable LDO Regulator Programming Regulator Protection The TPS730xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input voltage drops below the output voltage (for example, during power-down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be appropriate. The TPS730xx features internal current limiting and thermal protection. During normal operation, the TPS730xx limits output current to approximately 400mA. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package or the absolute maximum voltage ratings of the device. If the temperature of the device exceeds approximately +165C, thermal-protection circuitry shuts it down. Once the device has cooled down to below approximately +140C, regulator operation resumes. (c) 2004-2011, Texas Instruments Incorporated Submit Documentation Feedback 9 TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com TPS730xxYZQ NanoStarTM Wafer Chip Scale Information 0,79 0,84 1,30 1,34 0.625 Max NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. NanoStar package configuration. D. This package is tin-lead (SnPb); consult the factory for availability of lead-free material. NanoStar is a trademark of Texas Instruments. Figure 18. NanoStarTM Wafer Chip Scale Package 10 Submit Documentation Feedback (c) 2004-2011, Texas Instruments Incorporated TPS730xx SBVS054I - NOVEMBER 2004 - REVISED FEBRUARY 2011 www.ti.com REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision H (October, 2007) to Revision I * Page Corrected units in y-axis of Figure 6 ..................................................................................................................................... 5 (c) 2004-2011, Texas Instruments Incorporated Submit Documentation Feedback 11 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) TPS73001DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73001DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73001DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73001DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73018DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73018DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73018DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73018DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73018YZQR ACTIVE DSBGA YZQ 5 TBD Call TI TPS73018YZQT ACTIVE DSBGA YZQ 5 250 Green (RoHS & no Sb/Br) SNAGCU TPS73025DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73025DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73025DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73025DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73025YZQR ACTIVE DSBGA YZQ 5 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS73025YZQT ACTIVE DSBGA YZQ 5 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS730285DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) Addendum-Page 1 (3) Call TI Level-1-260C-UNLIM CU NIPDAU Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) TPS730285DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS730285DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS730285DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS730285YZQR ACTIVE DSBGA YZQ 5 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS730285YZQT ACTIVE DSBGA YZQ 5 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS73028DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73028DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73028DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73028DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73028YZQR ACTIVE DSBGA YZQ 5 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS73028YZQT ACTIVE DSBGA YZQ 5 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM TPS73030DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73030DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73030DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73030DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73030YZQR OBSOLETE DSBGA YZQ 5 TBD Call TI Call TI TPS73030YZQT OBSOLETE DSBGA YZQ 5 TBD Call TI Call TI TPS73033DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73033DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 2 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS73033DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73033DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73047DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73047DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73047DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS73047DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 Addendum-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) TPS73001DBVR SOT-23 DBV 6 3000 178.0 9.0 3.17 1.37 4.0 8.0 Q3 TPS73001DBVR SOT-23 DBV 6 3000 179.0 8.4 3.2 TPS73001DBVT SOT-23 DBV 6 250 178.0 9.0 3.23 3.2 1.4 4.0 8.0 Q3 3.17 1.37 4.0 8.0 TPS73018DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 Q3 3.17 1.37 4.0 8.0 TPS73018DBVT SOT-23 DBV 5 250 178.0 9.0 Q3 3.23 3.17 1.37 4.0 8.0 Q3 3.23 W Pin1 (mm) Quadrant TPS73018YZQT DSBGA YZQ 5 250 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS73025DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73025DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73025YZQR DSBGA YZQ 5 3000 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS73025YZQT DSBGA YZQ 5 250 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS730285DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS730285DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS730285YZQR DSBGA YZQ 5 3000 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS730285YZQT DSBGA YZQ 5 250 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS73028DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73028DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TPS73028YZQR DSBGA YZQ 5 3000 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 TPS73028YZQT DSBGA YZQ 5 250 178.0 8.4 0.98 1.46 0.69 4.0 8.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) TPS73030DBVR SOT-23 DBV 5 3000 178.0 9.0 TPS73030DBVT SOT-23 DBV 5 250 178.0 9.0 TPS73033DBVR SOT-23 DBV 5 3000 178.0 TPS73033DBVR SOT-23 DBV 5 3000 179.0 TPS73033DBVT SOT-23 DBV 5 250 TPS73047DBVR SOT-23 DBV 5 TPS73047DBVT SOT-23 DBV 5 W Pin1 (mm) Quadrant 3.23 3.17 1.37 4.0 8.0 Q3 3.23 3.17 1.37 4.0 8.0 Q3 9.0 3.23 3.17 1.37 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS73001DBVR SOT-23 DBV 6 3000 180.0 180.0 18.0 TPS73001DBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 TPS73001DBVT SOT-23 DBV 6 250 180.0 180.0 18.0 TPS73018DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73018DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73018YZQT DSBGA YZQ 5 250 217.0 193.0 35.0 TPS73025DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73025DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73025YZQR DSBGA YZQ 5 3000 217.0 193.0 35.0 TPS73025YZQT DSBGA YZQ 5 250 217.0 193.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS730285DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS730285DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS730285YZQR DSBGA YZQ 5 3000 217.0 193.0 35.0 TPS730285YZQT DSBGA YZQ 5 250 217.0 193.0 35.0 TPS73028DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73028DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73028YZQR DSBGA YZQ 5 3000 217.0 193.0 35.0 TPS73028YZQT DSBGA YZQ 5 250 217.0 193.0 35.0 TPS73030DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73030DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73033DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TPS73033DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0 TPS73033DBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TPS73047DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0 TPS73047DBVT SOT-23 DBV 5 250 203.0 203.0 35.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated