LM4819 350mW Audio Power Amplifier with Shutdown Mode General Description Key Specifications The LM4819 is a mono bridged power amplifier that is capable of delivering 350mWRMS output power into a 16 load or 300mWRMS output power into an 8 load with 10% THD+N from a 5V power supply. The LM4819 Boomer audio power amplifier is designed specifically to provide high quality output power and minimize PCB area with surface mount packaging and a minimal amount of external components. Since the LM4819 does not require output coupling capacitors, bootstrap capacitors or snubber networks, it is optimally suited for low-power portable applications. The closed loop response of the unity-gain stable LM4819 can be configured using external gain-setting resistors. The device is available in LLP, MSOP, and SO package types to suit various applications. n THD+N at 1kHz, 350mW continuous average output power into 16 10% (max) n THD+N at 1kHz, 300mW continuous average output power into 8 10% (max) n Shutdown Current 0.7A (typ) Features n n n n LLP, SOP, and MSOP surface mount packaging. Switch on/off click suppression. Unity-gain stable. Minimum external components. Applications n General purpose audio n Portable electronic devices n Information Appliances (IA) Typical Application DS200136-1 FIGURE 1. Typical Audio Amplifier Application Circuit Boomer (R) is a registered trademark of National Semiconductor Corporation. (c) 2002 National Semiconductor Corporation DS200136 www.national.com LM4819 350mW Audio Power Amplifier with Shutdown Mode April 2002 LM4819 Connection Diagrams SO Marking Small Outline (SO) Package DS200136-72 Top View XY - Date Code TT - Die Traceability Bottom 2 lines - Part Number DS200136-35 Top View Order Number LM4819M See NS Package Number M08A MSOP Marking Mini Small Outline (MSOP) Package DS200136-71 Top View G - Boomer Family 19 - LM4819MM DS200136-36 Top View Order Number LM4819MM See NS Package Number MUA08A LLP Package DS200136-74 Top View Order Number LM4819LD See NS Package Number LDA08B www.national.com 2 Infrared (15 seconds) Thermal Resistance If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. JC (MSOP) 56C/W JA (MSOP) 210C/W 35C/W 6.0V JC (SOP) -65C to +150C JA (SOP) 170C/W -0.3V to VDD +0.3V JA (LLP) 117C/W (Note 10) Internally Limited JA (LLP) 150C/W (Note 11) Supply Voltage Storage Temperature Input Voltage 220C Power Dissipation (PD) (Note 4) ESD Susceptibility (Note 5) 3.5kV ESD Susceptibility (Note 6) 250V Junction Temperature (TJ) 150C Operating Ratings (Notes 2, 3) Temperature Range Soldering Information (Note 1) TMIN TA TMAX Small Outline Package Vapor Phase (60 seconds) -40C TA 85C 2.0V VCC 5.5V Supply Voltage 215C Electrical Characteristics VDD = 5V (Notes 2, 3) The following specifications apply for VDD = 5V, RL = 16 unless otherwise stated. Limits apply for TA = 25C. LM4819 Symbol Parameter Conditions Typical Limit Units (Limits) (Note 7) (Notes 8, 9) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A 1.5 3.0 mA (max) ISD Shutdown Current VPIN1 = VDD (Note 12) 1.0 5.0 A (max) VSDIH Shutdown Voltage Input High 4.0 V (min) VSDIL Shutdown Voltage Input Low 1.0 V (max) VOS Output Offset Voltage 50 mV (max) PO Output Power THD+N Total Harmonic Distortion + Noise VIN = 0V 5 THD = 10%, fIN = 1kHz 350 mW THD = 10%, fIN = 1kHz, RL = 8 300 mW PO = 270mWRMS, AVD = 2, fIN = 1kHz 1 % Electrical Characteristics VDD = 3V (Notes 2, 3) The following specifications apply for VDD = 3V and RL = 16 load unless otherwise stated. Limits apply to TA = 25C. LM4819 Symbol Parameter Conditions Typical Limit Units (Limits) (Note 7) (Notes 8, 9) IDD Quiescent Power Supply Current VIN = 0V, Io = 0A 1.0 3.0 mA (max) ISD Shutdown Current VPIN1 = VDD (Note 12) 0.7 5.0 A (max) VSDIH Shutdown Voltage Input High 2.4 V (min) VSDIL Shutdown Voltage Input Low 0.6 V (max) VOS Output Offset Voltage PO Output Power THD+N Total Harmonic Distortion + Noise VIN = 0V 5 50 mV THD = 10%, fIN = 1kHz 110 mW THD = 10%, fIN = 1kHz, RL = 8 90 mW PO = 80mWRMS, AVD = 2, fIN = 1kHz 1 % 3 www.national.com LM4819 Absolute Maximum Ratings (Notes 2, 3) LM4819 Electrical Characteristics VDD = 3V (Notes 2, 3) The following specifications apply for VDD = 3V and RL = 16 load unless otherwise stated. Limits apply to TA = 25C. (Continued) Note 1: See AN-450 'Surface Mounting and their Effects on Product Reliability' for other methods of soldering surface mount devices. Note 2: All voltages are measured with respect to the ground pin, unless otherwise specified. Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given. However, the typical value is a good indication of device's performance. Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA. For the LM4819, TJMAX = 150C and the typical junction-to-ambient thermal resistance (JA) when board mounted is 210C/W for the MSOP package and 170C/W for the SOP package. Note 5: Human body model, 100pF discharged through a 1.5 k resistor. Note 6: Machine Model, 220pF-240pF capacitor is discharged through all pins. Note 7: Typical specifications are specified at 25C and represent the parametric norm. Note 8: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 9: Datasheet min/max specification limits are guaranteed by designs, test, or statistical analysis. Note 10: The given JA is for an LM4819 package in an LDA08B with the Exposed-DAP soldered to a printed circuit board copper pad with an area equivalent to that of the Exposed-DAP itself. The Exposed-DAP of the LDA08B package should be electrically connected to GND or an electrically isolated copper area. Note 11: The given JA is for an LM4819 package in an LDA08B with the Exposed-DAP not soldered to any printed circuit board copper. Note 12: The shutdown pin (pin1) should be driven as close as possible to VDD for minimum current in Shutdown Mode. External Components Description (Figure 1) Components Functional Description 1. Ri Combined with Rf, this inverting input resistor sets the closed-loop gain. Ri also forms a high pass filter with Ci at fc = 1/(2RiCi). 2. Ci This input coupling capacitor blocks DC voltage at the amplifier's terminals. Combined with Ri, it creates a high pass filter with Ri at fc = 1/(2RiCi). Refer to the section, Proper Selection of External Components for an explanation of how to determine the value of Ci. 3. Rf Combined with Ri, this is the feedback resistor that sets the closed-loop gain: Av = 2(RF/Ri). 4. CS This is the power supply bypass capacitor that filters the voltage applied to the power supply pin. Refer to the Application Information section for proper placement and selection of Cs. 5. CB This is the bypass pin capacitor that filters the voltage at the BYPASS pin. Refer to the section, Proper Selection of External Components, for information concerning proper placement and selection of CB. Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency DS200136-37 www.national.com DS200136-38 4 (Continued) THD+N vs Frequency THD+N vs Frequency DS200136-39 THD+N vs Frequency LM4819 Typical Performance Characteristics DS200136-40 THD+N vs Frequency DS200136-41 THD+N vs Output Power DS200136-42 THD+N vs Output Power DS200136-43 DS200136-44 5 www.national.com LM4819 Typical Performance Characteristics (Continued) THD+N vs Output Power THD+N vs Output Power DS200136-45 THD+N vs Output Power DS200136-73 THD+N vs Output Power DS200136-47 Output Power vs Supply Voltage RL = 8 DS200136-46 Output Power vs Supply Voltage RL = 16 DS200136-49 www.national.com DS200136-48 6 (Continued) Output Power vs Supply Voltage RL = 32 Output Power vs Load Resistance DS200136-51 Power Dissipation vs Output Power VDD = 5V LM4819 Typical Performance Characteristics DS200136-50 Power Dissipation vs Output Power VDD = 3V DS200136-53 Power Derating Curves DS200136-52 Frequency Response vs Input Capacitor Size DS200136-55 DS200136-54 7 www.national.com LM4819 Typical Performance Characteristics (Continued) Supply Current vs Supply Voltage DS200136-69 www.national.com 8 BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4819 consist of two operational amplifiers. External resistors, Ri and RF set the closed-loop gain of the first amplifier (and the amplifier overall), whereas two internal 20k resistors set the second amplifier's gain at -1. The LM4819 is typically used to drive a speaker connected between the two amplifier outputs. Figure 1 shows that the output of Amp1 servers as the input to Amp2, which results in both amplifiers producing signals identical in magnitude but 180 out of phase. Taking advantage of this phase difference, a load is placed between V01 and V02 and driven differentially (commonly referred to as 'bridge mode'). This results in a differential gain of AVD= 2 *(Rf/Ri) (1) Bridge mode is different from single-ended amplifiers that drive loads connected between a single amplifier's output and ground. For a given supply voltage, bridge mode has a distinct advantage over the single-ended configuration: its differential output doubles the voltage swing across the load. This results in four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output assumes that the amplifier is not current limited or the output signal is not clipped. To ensure minimum output signal clipping when choosing an amplifier's closed-loop gain, refer to the Audio Power Amplifier Design Example section. Another advantage of the differential bridge output is no net DC voltage across the load. This results from biasing V01 and V02 at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a single-ended configuration forces a single supply amplifier's half-supply bias voltage across the load. The current flow created by the halfsupply bias voltage increases internal IC power dissipation and may permanently damage loads such as speakers. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitors connected to the bypass and power supply pins should be placed as close to the LM4819 as possible. The capacitor connected between the bypass pin and ground improves the internal bias voltage's stability, producing improved PSRR. The improvements to PSRR increase as the bypass pin capacitor value increases. Typical applications employ a 5V regulator with 10F and 0.1F filter capacitors that aid in supply stability. Their presence, however, does not eliminate the need for bypassing the supply nodes of the LM4819. The selection of bypass capacitor values, especially CB , depends on desired PSRR requirements, click and pop performance as explained in the section, Proper Selection of External Components, as well as system cost and size constraints. POWER DISSIPATION Power dissipation is a major concern when designing a successful bridged or single-ended amplifier. Equation (2) states the maximum power dissipation point for a singleended amplifier operating at a given supply voltage and driving a specified load. PDMAX = (VDD)2 /(22RL ) (W) Single-ended (2) However, a direct consequence of the increased power delivered to the load by a bridged amplifier is an increase in the internal power dissipation point for a bridge amplifier operating at the same given conditions. Equation (3) states the maximum power dissipation point for a bridged amplifier operating at a given supply voltage and driving a specified load. PDMAX = 4(VDD)2/(22 RL ) (W) Bridge Mode (3) SHUTDOWN FUNCTION The voltage applied to the LM4819's SHUTDOWN pin controls the shutdown function. Activate micro-power shutdown by applying VDD to the SHUTDOWN pin. When active, the LM4819's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The logic threshold is typically 1/2VDD. The low 0.7A typical shutdown current is achieved by applying a voltage that is as near as VDD as possible to the SHUTDOWN pin. A voltage that is less than VDD may increase the shutdown current. Avoid intermittent or unexpected micro-power shutdown by ensuring that the SHUTDOWN pin is not left floating but connected to either VDD or GND. The LM4819 has two operational amplifiers in one package and the maximum internal power dissipation is four times that of a single-ended amplifier. However, even with this substantial increase in power dissipation, the Lm4819 does not require heatsinking. From Equation (3), assuming a 5V power supply and an 8 load, the maximum power dissipation point is 633mW. The maximum power dissipation point obtained from Equation (3) must not exceed the power dissipation predicted by Equation (4): PDMAX = (TJMAX - TA)/JA (W) (4) 9 www.national.com LM4819 For the micro MUA08A package, JA = 210C/W, for the M08A package, JA = 170C/W , and TJMAX = 150C for the LM4819. For a given ambient temperature, TA, Equation (4) can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation (3) is greater than the result of Equation (4), then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. For a typical application using the M08A packaged LM4819 with a 5V power supply and an 8 load, the maximum ambient temperature that does not violate the maximum junction temperature is approximately 42C. If a MUA08A packaged part is used instead with the same supply voltage and load, the maximum ambient temperature is 17C. In both cases, it is assumed that a device is a surface mount part operating around the maximum power dissipation point. The assumption that the device is operating around the maximum power dissipation point is incorrect for an 8 load. The maximum power dissipation point occurs when the output power is equal to the maximum power dissipation or 50% efficiency. The LM4819 is not capable of the output power level (633mW) required to operate at the maximum power dissipation point for an 8 load. To find the maximum power dissipation, the graph Power Dissipation vs. Output Power must be used. From the graph, the maximum power dissipation for an 8 load and a 5V supply is approximately 575mW. Substituting this value back into equation (4) for PDMAX and using JA = 210C/W for the MUA08A package, the maximum ambient temperature is calculated to be 29C. Using JA = 170C/W for the M08A package, the maximum ambient temperature is 52C. Refer to the Typical Performance Characteristics curves for power dissipation information for lower output powers and maximum power dissipation for each package at a given ambient temperature. Application Information LM4819 Application Information (5) f-3dB = 1/(2 RiCi) (Hz) As an example when using a speaker with a low frequency limit of 150Hz, Ci, using Equation (5) is 0.063F. The 0.39F Ci shown in Figure 1 allows the LM4819 to drive a high efficiency, full range speaker whose response extends down to 20Hz. (Continued) There are a few ways to activate micro-power shutdown. These included using a single-pole, single-throw switch, a microcontroller, or a microprocessor. When using a switch, connect an external 10k to 100k pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier operation by closing the switch. Opening the switch connects the shutdown pin to VDD through the pull-up resistor, activating micro-power shutdown. The switch and resistor guarantee that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or a microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor Besides optimizing the input capacitor value, the bypass capacitor value, CB requires careful consideration. The bypass capacitor's value is the most critical to minimizing turn-on pops because it determines how fast the LM4819 turns on. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the smaller the turn-on pop. While the device will function properly (no oscillations or motorboating), with CB less than 1.0F, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to or greater than 1.0F is recommended in all but the most cost sensitive designs. PROPER SELECTION OF EXTERNAL COMPONENTS Optimizing the LM4819's performance requires properly selecting external components. Though the LM4819 operates well when using external components with wide tolerances, best performance is achieved by optimizing component values. The LM4819 is unity gain stable, giving the designer maximum design flexibility. The gain should be set to no more than a given application requires. This allows the amplifier to achieve minimum THD+N and maximum signal-to-noise ratio. These parameters are compromised as the closed-loop gain increases. However, low gain demands input signals with greater voltage swings to achieve maximum output power. Fortunately, many signal sources such as audio CODECs have outputs of 1VRMS (2.83VP-P). Please refer to the Audio Power Amplifier Design section for more information on selecting the proper gain. Another important consideration is the amplifier's close-loop bandwidth. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, Ci, forms a first order high pass filter that limits low frequency response. This value should be chosen based on needed frequency response for a few distinct reasons discussed below Bypass Capacitor Value Selection Besides minimizing the input capacitor size, careful consideration should be paid to the value of CB, the capacitor connected to the BYPASS pin. Since CB determines how fast the LM4819 settles to quiescent operation, its value is critical when minimizing turn-on pops. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the smaller the turn-on pop. Choosing CB equal to 1.0F along with a small value of Ci (in the range of 0.1F to 0.39F) produces a click-less and pop-less shutdown function. As discussed above, choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops. Optimizing Click and Pop Reduction Performance The LM4819 contains circuitry that minimizes turn-on and shutdown transients or 'clicks and pops'. For this discussion, turn on refers to either applying the power or supply voltage or when the shutdown mode is deactivated. While the power supply is ramping to it's final value, the LM4819's internal amplifiers are configured as unity gain buffers. An internal current source charges the voltage of the bypass capacitor, CB, connected to the BYPASS pin in a controlled, linear manner. Ideally, the input and outputs track the voltage charging on the bypass capacitor. The gain of the internal amplifiers remains unity until the bypass capacitor is fully charged to 1/2VDD. As soon as the voltage on the bypass capacitor is stable, the device becomes fully operational. Although the BYPASS pin current cannot be modified, changing the size of the bypass capacitor, CB, alters the device's turn-on time and magnitude of 'clicks and pops'. Increasing the value of CB reduces the magnitude of turn-on pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time (Ton) increases. There is a linear relationship between the size of CB and the turn on time. Below are some typical turn-on times for various values of CB: Input Capacitor Value Selection Amplifying the lowest audio frequencies requires a high value input coupling capacitor (Ci in Figure 1). A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. Applications using speakers with limited frequency response reap little improvement by using a large input capacitor. Besides affecting system cost and size, Ci has an effect on the LM4819's click and pop performance. When the supply voltage is first applied, a transient (pop) is created as the charge on the input capacitor changes from zero to a quiescent state. The magnitude of the pop is directly proportional to the input capacitor's value. Higher value capacitors need more time to reach a quiescent DC voltage (usually 1/2 VDD) when charged with a fixed current. The amplifier's output charges the input capacitor through the feedback resistor, RF. Thus, selecting an input capacitor value that is no higher than necessary to meet the desired -3dB frequency can minimize pops. As shown in Figure 1, the input resistor (Ri) and the input capacitor, Ci produce a -3dB high pass filter cutoff frequency that is found using Equation (5). www.national.com CB 0.01F 10 TON 20ms 0.1F 200ms 0.22F 440ms 0.47F 940ms 1.0F 2S The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired 0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth limit. The gain variation for both response limits is 0.17dB, well with in the 0.25dB desired limit. The results are: fL = 100Hz/5 = 20Hz (Continued) In order to eliminate 'clicks and pops', all capacitors must be discharged before turn-on. Rapidly switching VDD may not allow the capacitors to fully discharge, which may cause 'clicks and pops'. AUDIO POWER AMPLIFIER DESIGN EXAMPLE The following are the desired operational parameters: fH = 20 kHz*5 = 100kHz As mentioned in the External Components section, Ri and Ci create a high pass filter that sets the amplifier's lower band pass frequency limit. Find the coupling capacitor's value using Equation (8). Given: Power Output Load Impedance Input Level Input Impedance 100mW 16 1Vrms (max) 20k Ci 1/(2Rifc) (F) (8) Ci 0.398F, a standard value of 0.39F will be used. The product of the desired high frequency cutoff (100kHz in this example) and the differential gain, AVD, determines the upper pass band response limit. With AVD = 1.27 and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 127kHz. This is less than the LM4819's 900kHz GBWP. With this margin the amplifier can be used in designs that require more differential gain while avoiding performance restricting bandwidth limitations. Bandwidth 100Hz-20kHz 0.25dB The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. To find this minimum supply voltage, use the Output Power vs. Supply Voltage graph in the Typical Performance Characteristics section. From the graph for a 16 load, (graphs are for 8, 16, and 32 loads) the supply voltage for 100mW of output power with 1% THD+N is approximately 3.15 volts. Additional supply voltage creates the benefit of increased headroom that allows the LM4819 to reproduce peaks in excess of 100mW without output signal clipping or audible distortion. The choice of supply voltage must also not create a situation that violates maximum dissipation as explained above in the Power Dissipation section. For example, if a 3.3V supply is chosen for extra headroom then according to Equation (3) the maximum power dissipation point with a 16 load is 138mW. Using Equation (4) the maximum ambient temperature is 121C for the MUA08A package and 126C for the M08A package. After satisfying the LM4819's power dissipation requirements, the minimum differential gain is found using Equation (6). (6) Thus a minimum gain of 1.27 V/V allows the LM4819 to reach full output swing and maintain low noise and THD+N performance. For this example, let AVD = 1.27. The amplifier's overall gain is set using the input (Ri) and feedback (RF) resistors. With the desired input impedance set to 20k, the feedback resistor is found using Equation (7). RF/Ri = AVD/2 (V/V) (7) The value of RF is 13k. 11 www.national.com LM4819 Application Information LM4819 Application Information (Continued) HIGHER GAIN AUDIO AMPLIFIER DS200136-24 Figure 2 The LM4819 is unity-gain stable and requires no external components besides gain-setting resistors, an input coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential gain of greater than 10 is required, a feedback capacitor (C4) may be needed as shown in Figure 2 to bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that eliminates possible high frequency oscillations. Care should be www.national.com taken when calculating the -3dB frequency in that an incorrect combination of R3 and C4 will cause rolloff before 20kHz. A typical combination of feedback resistor and capacitor that will not produce audio band high frequency rolloff is R3 = 20k and C4 = 25pF. These components result in a -3dB point of approximately 320 kHz. It is not recommended that the feedback resistor and capacitor be used to implement a band limiting filter below 100kHz. 12 LM4819 Application Information (Continued) DIFFERENTIAL AMPLIFIER CONFIGURATION FOR LM4819 DS200136-29 Figure 3 13 www.national.com LM4819 Application Information (Continued) REFERENCE DESIGN BOARD and PCB LAYOUT GUIDELINES DS200136-68 Figure 4 www.national.com 14 LM4819 Application Information (Continued) LM4819 SO DEMO BOARD ARTWORK Silk Screen Top Layer DS200136-62 DS200136-63 Bottom Layer DS200136-64 15 www.national.com LM4819 Application Information (Continued) LM4819 MSOP DEMO BOARD ARTWORK Silk Screen Top Layer DS200136-65 DS200136-66 Bottom Layer DS200136-67 www.national.com 16 LM4819 Application Information (Continued) LM4819 LD DEMO BOARD ARTWORK Silk Screen Composite View DS200136-31 DS200136-32 Bottom Layer Top Layer DS200136-30 DS200136-33 17 www.national.com LM4819 Application Information (Continued) Mono LM4819 Reference Design Boards Bill of Material for all Demo Boards Item Part Number Part Description Qty Ref Designator 1 551011208-001 LM4819 Mono Reference Design Board 1 10 482911183-001 LM4819 Audio AMP 1 U1 20 151911207-001 Tant Cap 1uF 16V 10 1 C1 21 151911207-002 Cer Cap 0.39uF 50V Z5U 20% 1210 1 C2 25 152911207-001 Tant Cap 1uF 16V 10 1 C3 30 472911207-001 Res 20K Ohm 1/10W 5 3 R1, R2, R3 35 210007039-002 Jumper Header Vertical Mount 2X1 0.100 2 J1, J2 Single-Point Power / Ground Connections The analog power traces should be connected to the digital traces through a single point (link). A 'Pi-filter' can be helpful in minimizing high frequency noise coupling between the analog and digital sections. It is further recommended to put digital and analog power traces over the corresponding digital and analog ground traces to minimize noise coupling. PCB LAYOUT GUIDELINES This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power and ground traces. Designers should note that these are only 'rule-of-thumb' recommendations and the actual results will depend heavily on the final layout. General Mixed Signal Layout Recommendation Placement of Digital and Analog Components All digital components and high-speed digital signals traces should be located as far away as possible from analog components and circuit traces. Power and Ground Circuits For two layer mixed signal design, it is important to isolate the digital power and ground trace paths from the analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even device. This technique will take require a greater amount of design time but will not increase the final price of the board. The only extra parts required will be some jumpers. www.national.com Avoiding Typical Design / Layout Problems Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90 degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise coupling and cross talk. 18 LM4819 Physical Dimensions inches (millimeters) unless otherwise noted MSOP Order Number LM4819MM NS Package Number MUA08A 19 www.national.com LM4819 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) SO Order Number LM4819M NS Package Number M08A www.national.com 20 LM4819 350mW Audio Power Amplifier with Shutdown Mode Physical Dimensions inches (millimeters) unless otherwise noted (Continued) LLP Order Number LM4819LD NS Package Number LDA08B LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.