Document Number: 42016 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 19-Feb-07 25
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
FEATURES
Utilizes minimum area where printed wiring
board space is most important
Wound from PETP polyester film and thin gauge
foil under carefully controlled atmospheric
conditions
Protected against moisture by a conformal coating of
epoxy
Specifically designed for printed wiring board applications
Widely used in computers, instrumentation and
telecommunications equipment
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
To + 105 °C when working voltage is reduced to 70 % of
+ 85 °C rating; to + 125 °C when working voltage is reduced
to 50 % of 85 °C rating
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C 0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C 0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C 0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C 0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
Dielectric Withstanding Voltage:
Capacitors shall withstand a DC potential of 250 % of rated
voltage applied between terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
RoHS
COMPLIANT
DIMENSIONS in inches [millimeters]
CASE
CODE
L
(Max.)
S
Terminal A and B Terminal D
W 0.70 [17.78] 0.562 [14.275] 0.375 [9.525]
X 0.80 [20.32] 0.613 [15.570] 0.375 [9.525]
Y 1.25 [31.75] 0.969 [24.613] 0.719 [18.263]
Terminal A
L
Max.
0.237
[6.020]
Max.
S
± 0.060 [1.524]
Lead
Length
"
Terminal B
0.237
[6.020]
Max.
L
Max.
S
± 0.030 [0.762]
Lead
Length
0.237
[6.020]
Max.
Terminal D
L
Max.
S
± 0.030 [0.762]
T Max.
H
Max.
Lead
Length
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42016
26 Revision: 19-Feb-07
Type 225P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3).
** 60 Hz rms
CAPACITANCE CHANGE
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
16
14
12
10
8
6
4
2
0
2
4
6
zH0001/EGNAHC ECNATICAPAC
%
CAPACITANCE CHANGE ENVELOPE
FOR 96 % CONFIDENCE LEVEL
TEMPERATURE DEG. CENTIGRADE
DISSIPATION FACTOR VS.TEMPERATURE
TYPICAL
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
TEMPERATURE DEG. CENTIGRADE
1
.5
1.0
0.5
0
% DISSIPATION/1000 Hz
STANDARD RATINGS*
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
100 VDC/70 VAC**
0.001 225P10291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0012 225P12291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0015 225P15291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0018 225P18291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0022 225P22291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0027 225P27291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0033 225P33291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0039 225P39291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0047 225P47291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0056 225P56291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0068 225P68291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0082 225P82291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.01 225P10391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.012 225P12391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.015 225P15391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.018 225P18391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.022 225P22391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.027 225P27391W 0.70 [17.78] 0.37 [9.40] 0.27 [6.86]
0.033 225P33391W 0.70 [17.78] 0.37 [9.40] 0.27 [6.86]
0.039 225P39391W 0.70 [17.78] 0.42 [10.67] 0.30 [7.62]
0.047 225P47391W 0.70 [17.78] 0.42 [10.67] 0.30 [7.62]
0.056 225P56391W 0.70 [17.78] 0.49 [12.45] 0.34 [8.64]
0.068 225P68391W 0.70 [17.78] 0.49 [12.45] 0.34 [8.64]
0.082 225P82391W 0.70 [17.78] 0.55 [13.97] 0.40 [10.16]
0.1 225P10491W 0.70 [17.78] 0.55 [13.97] 0.40 [10.16]
0.12 225P12491X 0.80 [20.32] 0.57 [14.48] 0.37 [9.40]
0.15 225P15491X 0.80 [20.32] 0.62 [15.75] 0.40 [10.16]
0.18 225P18491X 0.80 [20.32] 0.66 [16.76] 0.43 [10.92]
0.22 225P22491X 0.80 [20.32] 0.70 [17.78] 0.46 [11.68]
0.27 225P27491X 0.80 [20.32] 0.74 [18.80] 0.49 [12.45]
0.33 225P33491X 0.80 [20.32] 0.77 [19.56] 0.52 [13.21]
0.39 225P39491X 0.80 [20.32] 0.81 [20.57] 0.55 [13.97]
0.47 225P47491X 0.80 [20.32] 0.86 [21.84] 0.60 [15.24]
0.56 225P56491Y 1.25 [31.75] 0.88 [22.35] 0.55 [13.97]
0.68 225P68491Y 1.25 [31.75] 0.90 [22.86] 0.58 [14.73]
0.82 225P82491Y 1.25 [31.75] 0.94 [23.88] 0.65 [16.51]
1.0 225P10591Y 1.25 [31.75] 0.98 [24.89] 0.72 [18.29]
Type 225P
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead Vishay Sprague
Document Number: 42016 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 19-Feb-07 27
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
** 60 Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
200 VDC/140 VAC**
0.001 225P10292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0068 225P68292X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.015 225P15392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.022 225P22392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.033 225P33392X 0.80 [20.32] 0.61 [15.49] 0.28 [7.11]
0.047 225P47392X 0.80 [20.32] 0.61 [15.49] 0.28 [7.11]
0.068 225P68392X 0.80 [20.32] 0.64 [16.26] 0.31 [7.87]
0.1 225P10492X 0.80 [20.32] 0.71 [18.03] 0.37 [9.40]
0.1 225P10492Y 1.25 [31.75] 0.64 [16.26] 0.31 [7.87]
0.15 225P15492X 0.80 [20.32] 0.74 [18.80] 0.41 [10.41]
0.22 225P22492X 0.80 [20.32] 0.77 [19.56] 0.48 [12.19]
0.33 225P33492Y 1.25 [31.75] 0.71 [18.03] 0.41 [10.41]
0.47 225P47492Y 1.25 [31.75] 0.83 [21.08] 0.50 [12.70]
0.68 225P68492Y 1.25 [31.75] 1.14 [28.96] 0.84 [21.34]
400 VDC/200 VAC**
0.001 225P10294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0068 225P68294X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10394X 0.80 [20.32] 0.58 [14.73] 0.28 [7.11]
0.015 225P15394X 0.80 [20.32] 0.58 [14.73] 0.28 [7.11]
0.022 225P22394X 0.80 [20.32] 0.58 [14.73] 0.31 [7.87]
0.033 225P33394X 0.80 [20.32] 0.65 [16.51] 0.34 [8.64]
0.047 225P47394X 0.80 [20.32] 0.65 [16.51] 0.41 [10.41]
0.047 225P47394Y 1.25 [31.75] 0.64 [16.26] 0.31 [7.87]
0.068 225P68394X 0.80 [20.32] 0.80 [20.32] 0.47 [11.94]
0.1 225P10494X 0.80 [20.32] 0.84 [21.34] 0.52 [13.21]
0.1 225P10494Y 1.25 [31.75] 0.74 [18.80] 0.41 [10.41]
0.15 225P15494Y 1.25 [31.75] 0.80 [20.32] 0.47 [11.94]
0.22 225P22494Y 1.25 [31.75] 0.89 [22.61] 0.56 [14. 22]
0.33 225P33494Y 1.25 [31.75] 0.99 [25.15] 0.72 [18.29]
0.47 225P47494Y 1.25 [31.75] 1.14 [28.96] 0.84 [21.34]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42016
28 Revision: 19-Feb-07
Type 225P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
* 60 Hz rms
Note: Some Part Numbers are in stock and available through the Vishay Sprague® Distribution Network. Other Part Numbers are available on
special order through Vishay Sprague® Distribution. In the construction of the components described, the full intent of the specification will be
met. Vishay however, reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit
improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Vishay Sprague®
assumes no responsibility for its use nor for any infringements of patens of other rights of third parties which may result from its use.
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
600 VDC/200 VAC**
0.001 225P10296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47296X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.0068 225P68296X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10396X 0.80 [20.32] 0.64 [16.26] 0.31 [7.87]
0.015 225P15396X 0.80 [20.32] 0.67 [17.02] 0.34 [8.64]
0.018 225P18396X 0.80 [20.32] 0.74 [18.80] 0.37 [9.40]
0.022 225P22396X 0.80 [20.32] 0.74 [18.80] 0.37 [9.40]
0.033 225P33396X 0.80 [20.32] 0.77 [19.56] 0.44 [11.18]
0.039 225P39396X 0.80 [20.32] 0.83 [21.08] 0.50 [12.70]
0.047 225P47396X 0.80 [20.32] 0.83 [21.08] 0.50 [12.70]
0.068 225P68396Y 1.25 [31.75] 0.82 [20.83] 0.47 [11.94]
0.1 225P10496Y 1.25 [31.75] 0.91 [23.11] 0.56 [14.22]
0.22 225P22496Y 1.25 [31.75] 1.10 [27.94] 0.76 [19.30]
ORDERING INFORMATION
225P 104 9 1 W D 3 (-XXX)
TYPE CAPACITANCE TOLERANCE DC VOLTAGE
RATING
CASE CODE TERMINAL LEAD LENGTH SPECIAL
CONSTRUCTION
Capacitance is
expressed in
picofarads. The first
two digits are
significant. The third
is the number of
zeros to follow.
Values must
conform to Decade
Rating for the
tolerance specified.
0 = ± 20 %
9 = ± 10 %
5 = ± 50 %
This is
expressed in
hundred of
volts.
See Dimensional
Configurations.
A = Straight Lead
B = Hairpin Crimped
D = Hockey Crimped
1 = 0.187" ± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250” [31.750]
Minimum
A three-digit suffix
may be added by
the factory to
denote special
construction.
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.