Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit Data Sheet M28331/M28332/M28333 (-3x) 28333-DSH-003-A March 2003 Revision History Revision Level Date A -- June 2001 A -- February 2003 Description Initial release - Updated LBO to 450 feet. - Incorporated Errata # 500377A. - Added loopback diagrams. - Removed EVM, IBIS, and JAT Appendices. - Fixed description of transmit AIS during loopback operations. - Renumbered document [28333-DSH-003-A]. - Updated PCB design considerations. - Added power sequencing information. - General corrections. (c) 2002, 2003 Mindspeed TechnologiesTM, a Conexant business All Rights Reserved. Information in this document is provided in connection with Mindspeed Technologies ("Mindspeed") products. These materials are provided by Mindspeed as a service to its customers and may be used for informational purposes only. Mindspeed assumes no responsibility for errors or omissions in these materials. Mindspeed may make changes to specifications and product descriptions at any time, without notice. Mindspeed makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Mindspeed's Terms and Conditions of Sale for such products, Mindspeed assumes no liability whatsoever. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MINDSPEED PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MINDSPEED FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MINDSPEED SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. Mindspeed products are not intended for use in medical, lifesaving or life sustaining applications. Mindspeed customers using or selling Mindspeed products for use in such applications do so at their own risk and agree to fully indemnify Mindspeed for any damages resulting from such improper use or sale. The following are trademarks of Conexant Systems, Inc.: Mindspeed TechnologiesTM, the MindspeedTM logo, and "Build It First"TM. Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Third-party brands and names are the property of their respective owners. For additional disclaimer information, please consult Mindspeed Technologies Legal Information posted at www.mindspeed.com which is incorporated by reference. 28333-DSH-003-A Mindspeed TechnologiesTM M28331/M28332/M28333 (-3x) Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit The M28333 is a three-channel, DS3/E3/STS-1, fully integrated Line Interface Unit Distinguishing Features (LIU) device. It is configured via external pins and does not require a microprocessor * Programmable pulse shaper to meet interface. Each channel has an independent receive equalizer requiring no user cross-connect pulse masks (ANSI T1.1021993) configuration. Additionally, each channel has a programmable transmit pulse shaper * Meets jitter tolerance and jitter generation that can be set to ensure that the transmit pulse meets the pulse mask requirement specifications of Bellcore GR499, GR253, for the digital cross-connect. The M28332 is a dual-channel, and the M28331 is a and ETSI TBR24 single-channel LIU with performance identical to the M28333. * The M28333 gives the user new economies of scale in concentrator applications where three DS3 or STS-1 channels are concentrated into a single STS-3 channel. * * Each line interface is reduced to 1:1 coupling transformers, terminating resistors, and * a capacitor. The Transmit Line Driver Monitor checks for a faulty transmitter or shorted output. NOTE: In this document, "i" is used to represent the number of channels: i = 1 (M28331), i = 2 (M28332), and i = 3 (M28333). * * * Functional Block Diagram * * XOE LBO E3MODE Physical Characteristics * * * PDB TPOS TNEG TCLK PDATA/ NDATA ENCODER RPOS RNEG RCLK Pulse Shaper LINE DRIVER TLINEP TLINEM/N TCLK DATA MUX TX Monitor ENDECDIS TAIS RLOOP LLOOP Alarms for coding violation and loss of signal Full diagnostic loopback capability Uses a minimum of external components Compliant with ITU-T G.703 and ETSI TBR24 Independent power down mode per channel Easily interfaced to the DS3/E3 Framer IC (CX28342/3/4/6/8 and CN8330) Selectable B3ZS/HDB3 encoding/ decoding Transmit monitor inputs Programmable RLOS threshold DECODER RLOS 28333-DSH-003-A TMONP TMONM TXMON TMONTST REFCLK PDATA Clock/ NDATA Data DATCLK Recovery P N RLOSMAX RLOSTHR RLOSMDIS Receiver ALOS RLINEP RLINEM/N * * * 100-pin ETQFP package Single 3.3 V power supply 1 W maximum power dissipation (M28333) - 40 C to +85 C temperature range 5 V-tolerant pins TTL digital pins Applications * * * * * * * Digital Cross-Connect Systems Routers ATM Switches Channelized Line Aggregation Units Test Equipment Channel Service Units Multiplexers REQH Channel 1 Channel 2 Channel 3 Mindspeed TechnologiesTM iii M28333 EVM TX B3ZS/HDB3 analog out NRZTX DATA and CLK in CH1 CH1 NRZRX DATA and CLK out F R A M E R S I D E RX B3ZS/HDB3 analog in TX B3ZS/HDB3 analog out NRZTX DATA and CLK in CH2 NRZRX DATA and CLK out M28333 CH2 RX B3ZS/HDB3 analog in TX B3ZS/HDB3 analog out NRZTX DATA and CLK in CH3 CH3 NRZRX DATA and CLK out L I N E S I D E RX B3ZS/HDB3 analog in Loss of Signal Clock Input Code Violation Control 100985_002 Ordering Information iv Model Number Package Description Operating Temperature M28331-3x 100-Pin ETQFP Single channel with Transmit Monitoring -40 C to +85 C M28332-3x 100-Pin ETQFP Dual channel with Transmit Monitoring -40 C to +85 C M28333-3x 100-Pin ETQFP Triple channel with Transmit Monitoring -40 C to +85 C Mindspeed TechnologiesTM 28333-DSH-003-A Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix 1.0 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 2.0 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.2 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.3 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.3.7 2.4 Receive Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AGC/VGA Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receive Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The PLL Clock Recovery Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receive Loss Of Signal (RLOS) Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B3ZS/HDB3 Decoder With Bipolar Violation Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Squelching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 2-10 2-10 2-11 2-11 2-11 2-12 Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 2.4.1 2.5 AMI B3ZS/HDB3 Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Pulse Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Line Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 2.2.3.1 Transmit Pulse Mask Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Alarm Indication Signal (AIS) Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Transmit Monitor Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Jitter Generation (Intrinsic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Jitter Transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Additional M2833i Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 2.5.1 2.5.2 2.5.3 28333-DSH-003-A Bias Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Power-On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Loopback Multiplexers (MUXes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Mindspeed TechnologiesTM v M28331/M28332/M28333 (-3x) Table of Contents Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.6 Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 2.7 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 2.7.1 2.7.2 2.7.3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 ESD Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 2.8 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 2.9 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 2.10 Transceiver Specification Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 3.0 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.1 PCB Design Considerations for the M2833i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 3.1.6 Power Supply and Ground Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Component Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.1.2.1 RBIAS Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.1.2.2 VGG Decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3.1.2.3 Termination Resistors and Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Impedance Matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Other Passive Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 IBIS Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Recommended Vendors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Appendix A: Applicable Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Appendix B: Exposed Thin Quad Flat (ETQFP) Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 B.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 B.2 Package Thermal Characterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 B.2.1 B.2.2 B.2.3 B.2.4 B.2.5 Heat Removal Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Lands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PCB Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Test Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.2.4.1 Test Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.2.4.2 Thermal Test Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Thermal Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.2.5.1 Calculation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B.2.5.2 Package Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 B-3 B-5 B-6 B-6 B-6 B-7 B-7 B-7 B.3 Solder Stencil Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 B.4 Solder Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 Appendix C: Power Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 vi Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) List of Figures Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit List of Figures Figure 1-1. Figure 1-2. Figure 1-3. Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-7. Figure 2-8. Figure 2-9. Figure 2-10. Figure 2-11. Figure 2-12. Figure 2-13. Figure 2-14. Figure 3-1. Figure B-1. Figure B-2. Figure B-3. Figure B-4. Figure B-5. Figure B-6. Figure B-7. Figure B-8. Figure B-9. Figure B-10. Figure C-1. Figure C-2. 28333-DSH-003-A M28331-3x Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 M28332-3x Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 M28333-3x Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Typical Application Of Single M2833i Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Pulse Shaper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Pulse Measurement Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Transmit Pulse Mask for DS3 Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Transmit Pulse Mask for STS-1 Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Transmit Pulse Mask for E3 Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 AIS Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Minimum Jitter Tolerance Requirement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Maximum Jitter Transfer Curve Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Remote Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 Local Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 M2833i-3x Mechanical Drawing (100-Pin)--Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 Test Setup for Measurement of Output Pulse Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 DS3/E3 Application Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Schematic Representation of the Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Package and PCB Land Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Internal Structure for a Two-Layer PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5 Internal Structure For a Six-Layer PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5 Test Performance Structure (A = 100 mm, B = 100 mm, LP = 1.40 mm, LB = 1.60 mm) . . B-6 Package Thermal Resistance as a Function of Airflow Velocity for a 48-ETQFP Package . . B-7 Package Thermal Resistance as a Function of Airflow Velocity for an 64 ETQFP. . . . . . . . . B-8 Package Thermal Resistance as a Function of Airflow Velocity for an 80 ETQFP. . . . . . . . . B-8 Typical IR Reflow Profile for Eutectic Sn63:Pb37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 Typical Forced Convection Reflow Profile for Eutectic Sn63:Pb37 . . . . . . . . . . . . . . . . . . B-11 Power -up sequence of VGG and VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Power-down sequence of VGG and VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Mindspeed TechnologiesTM vii M28331/M28332/M28333 (-3x) List of Figures Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit viii Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) List of Tables Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit List of Tables Table 1-1. Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 2-5. Table 2-6. Table 2-7. Table 2-8. Table 2-9. Table 2-10. Table 2-11. Table B-1. Table B-2. Table B-3. Table B-4. Table B-5. 28333-DSH-003-A M2833i-3x Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 DS3 Transmit Template Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 STS-1 Transmit Template Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 RLOS Threshold Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 ESD Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 DC Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 AC Characteristics (Logic Timing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Receiver Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 Transmitter Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 Intrinsic Jitter Specifications (Receiver to Transmitter using Remote Loopback) . . . . . . . . 2-26 Dimensional Parameters (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 Specification for a Two-Layer Test Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6 Specification for a Four-Layer Test Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6 Specification for Delco Thermal Test Chips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7 Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-8 Mindspeed TechnologiesTM ix M28331/M28332/M28333 (-3x) List of Tables Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit x Mindspeed TechnologiesTM 28333-DSH-003-A 1 1.0 Pin Description 1.1 Pin Assignments Figures 1-1 (M28331-3x), 1-2 (M28332-3x), and 1-3 (M28333-3x) illustrate pin assignments for the 100-pin ETQFP. The input/output (I/O) column is coded as follows: I = Input O = Output I/O = Bidirectional P = Power NOTE: All digital inputs and outputs contain 75 k pull-down resistors. When a channel is disabled (i.e., the PDx pin is tied low or not connected), all receive and transmit analog circuitry powers down. Analog inputs (RLINE) are ignored and analog outputs (TLINE) are high impedance. Digital inputs of a powered-down channel are still active, but ignored. Overall noise on the device can be lowered by not driving the digital inputs of a powered-down channel. NOTE: 28333-DSH-003-A When power is disconnected from the device, TLINE pins are low impedance to ground if driven by more than one forward-bias diode voltage (0.7 V) below ground. Additionally, driving TLINE, a forward-bias diode voltage above the VGG pin, creates a low impedance path from the TLINE pin to the VGG pin. Otherwise, the TLINE pins are high impedance. Mindspeed TechnologiesTM 1-1 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 VSS RBIAS VGG RESET GPD NC NC NC DVDDIO NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC Figure 1-1. M28331-3x Pin Diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 M28331-3x 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DVDDC ENDECDIS PD RLOOP LLOOP RNEG/RLCV RPOS/RNRZ RCLK RLOS RLOSMAX RLOSTHR RLOSMDIS TAIS TCLK TPOS/TNRZ TNEG/NC TLOS REFCLK REQH XOE LBO TMONTST E3MODE NC DVSSC VDD NC NC VSS NC NC NC DVSSIO NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NC NC NC NC VDD VDD NC NC VSS TVSS TMONP TLINEP TLINEM TMONM TVDD RVDD RLINEP RLINEM RVSS VSS NC NC NC NC VDD 100985_015 1-2 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 TVSS1 RBIAS VGG RESET GPD PD1 RLOOP1 LLOOP1 DVDDIO LBO1 XOE1 REQH1 RLOSMAX1 RLOSTHR1 RLOSMDIS1 RNEG1/RLCV1 RPOS1/RNRZ1 RCLK1 RLOS1 REFCLK1 TLOS1 TNEG1/NC1 TPOS1/TNRZ1 TCLK1 TAIS1 Figure 1-2. M28332-3x Pin Diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 M28332-3x 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DVDDC ENDECDIS NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC TMONTST E3MODE NC DVSSC RVDD2 RLINE2P RLINE2M RVSS2 PD2 RLOOP2 LLOOP2 DVSSIO LBO2 XOE2 REQH2 RLOSMAX2 RLOSTHR2 RLOSMDIS2 RNEG2/RLCV2 RPOS2/RNRZ2 RCLK2 RLOS2 REFCLK2 TLOS2 TNEG2/NC2 TPOS2/TNRZ2 TCLK2 TAIS2 NC 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 TMON1P TLINE1P TLINE1M TMON1M TVDD1 RVDD1 RLINE1P RLINE1M RVSS1 VSS NC NC NC NC VDD VDD NC NC VSS TVSS2 TMON2P TLINE2P TLINE2M TMON2M TVDD2 100985_016 28333-DSH-003-A Mindspeed TechnologiesTM 1-3 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 TVSS1 RBIAS VGG RESET GPD PD1 RLOOP1 LLOOP1 DVDDIO LBO1 XOE1 REQH1 RLOSMAX1 RLOSTHR1 RLOSMDIS1 RNEG1/RLCV1 RPOS1/RNRZ1 RCLK1 RLOS1 REFCLK1 TLOS1 TNEG1/NC1 TPOS1/TNRZ1 TCLK1 TAIS1 Figure 1-3. M28333-3x Pin Diagram 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 M28333-3x 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 DVDDC ENDECDIS PD2 RLOOP2 LLOOP2 RNEG2 / RLCV2 RPOS2 / RNRZ2 RCLK2 RLOS2 RLOSMAX2 RLOSTHR2 RLOSMDIS2 TAIS2 TCLK2 TPOS2/TNRZ2 TNEG2/NC2 TLOS2 REFCLK2 REQH2 XOE2 LBO2 TMONTST E3MODE NC DVSSC RVDD3 RLINE3P RLINE3M RVSS3 PD3 RLOOP3 LLOOP3 DVSSIO LBO3 XOE3 REQH3 RLOSMAX3 RLOSTHR3 RLOSMDIS3 RNEG3/RLCV3 RPOS3/RNRZ3 RCLK3 RLOS3 REFCLK3 TLOS3 TNEG3/NC3 TPOS3/TNRZ3 TCLK3 TAIS3 NC 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 TMON1P TLINE1P TLINE1M TMON1M TVDD1 RVDD1 RLINE1P RLINE1M RVSS1 TVSS2 TMON2P TLINE2P TLINE2M TMON2M TVDD2 RVDD2 RLINE2P RLINE2M RVSS2 TVSS3 TMON3P TLINE3P TLINE3M TMON3M TVDD3 100985_006 1-4 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (1 of 9) Pin # Signal Name Description I/O/P Notes Ch1 positive receive data I Ch1 negative receive data I Differential inputs for each channel from its respective receive coax line. The RX expects balanced differential inputs, usually achieved using a 1:1 transformer. The inputs are internally DC biased to 1.9 V. M28331-3x M28332-3x M28333-3x Coaxial Line Pins 17 -- -- RLINEP -- 7 7 RLINE1P 18 -- -- RLINEM -- 8 8 RLINE1M -- 27 17 RLINE2P Ch2 positive receive data I -- 28 18 RLINE2M Ch2 negative receive data I -- -- 27 RLINE3P Ch3 positive receive data I -- -- 28 RLINE3M Ch3 negative receive data I 12 -- -- TLINEP O -- 2 2 TLINE1P Ch1 positive transmit data 13 -- -- TLINEM O -- 3 3 TLINE1M Ch1 negative transmit data -- 22 12 TLINE2P Ch2 positive transmit data O -- 23 13 TLINE2M Ch2 negative transmit data O -- -- 22 TLINE3P Ch3 positive transmit data O -- -- 23 TLINE3M Ch3 negative transmit data O 28333-DSH-003-A Mindspeed TechnologiesTM Differential, coax-driver balanced outputs for pulse-shaped AMI B3ZS/HDB3 encoded waveforms for each channel. These pins should be connected to the primary side of the 1:1 transformer through two backmatch resistors. See Figure 3-1. 1-5 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (2 of 9) Pin # Signal Name Description I/O/P Notes O Resynchronized receive data intended to be strobed out by the corresponding RCLK. M28331-3x M28332-3x M28333-3x Digital Data Pins 1-6 69 -- -- RPOS/ RNRZ -- 84 84 RPOS1/ RNRZ1 70 -- -- RNEG/ RLCV -- 85 85 RNEG1/ RLCV1 -- 41 69 -- 40 -- Ch1 receive Positive rail or NRZ data Ch1 receive Negative rail or line code violation O When ENDECDIS = 1, these outputs are positive and negative AMI data (RPOS and RNEG). RPOS2/ RNRZ2 Ch2 receive Positive rail or NRZ data O When ENDECDIS = 0, these outputs are decoded NRZ data (RNRZ) and line code violation (RLCV). A line code violation is indicated when RLCV = 1. 70 RNEG2/ RLCV2 Ch2 receive Negative rail or line code violation O See notes on the ENDECDIS pin in the Control Signals section. -- 41 RPOS3/ RNRZ3 Ch3 receive Positive rail or NRZ data O -- -- 40 RNEG3/ RLCV3 Ch3 receive Negative rail or line code violation O 68 -- -- RCLK O -- 83 83 RCLK1 Receive clock Ch1 -- 42 68 RCLK2 Receive clock Ch2 O -- -- 42 RCLK3 Receive clock Ch3 O Mindspeed TechnologiesTM Recovered clock for each channel receiver, intended for strobing the corresponding RDAT into the following framer or logic. 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (3 of 9) Pin # Signal Name Description I/O/P Notes Ch1 transmit Positive rail or NRZ data I Synchronized transmit data intended to be strobed in by the corresponding TCLK. Ch1 transmit Negative rail or no connect data I M28331-3x M28332-3x M28333-3x 61 -- -- TPOS/ TNRZ -- 78 78 TPOS1/ TNRZ1 60 -- -- TNEG/ NC -- 79 79 TNEG1/ NC1 -- 47 61 TPOS2/ TNRZ2 Ch2 transmit Positive or NRZ data I -- 46 60 TNEG2/ NC2 Ch2 transmit Negative data or no connect data I -- -- 47 TPOS3/ TNRZ3 Ch3 transmit Positive or NRZ data I -- -- 46 TNEG3/NC3 Ch3 transmit Negative data or no connect data I 62 -- -- TCLK I -- 77 77 TCLK1 Transmit clock Ch1 -- 48 62 TCLK2 Transmit clock Ch2 I -- -- 48 TCLK3 Transmit clock Ch3 I 67 -- -- RLOS O -- 82 82 RLOS1 Loss of signal Ch1 -- 43 67 RLOS2 Loss of signal Ch2 O -- -- 43 RLOS3 Loss of signal Ch3 O 28333-DSH-003-A Mindspeed TechnologiesTM When ENDECDIS = 1, these inputs are expected to be positive and negative AMI data (TPOS and TNEG). When ENDECDIS = 0, these inputs are expected to be uncoded NRZ data (TNRZ) and no connects (NC). See notes on the ENDECDIS pin in the Control Signal section. Transmit bit clock input for strobing with transmit data into the M2833i. Loss Of Signal (LOS) indication for each channel, as determined by insufficient pulse density. Signal loss detected when RLOS = 1. Loss of signal is asserted and deasserted under the conditions discussed in Section 2.3.5. 1-7 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (4 of 9) Pin # Signal Name Description I/O/P Notes M28331-3x M28332-3x M28333-3x RLOS Threshold and Control 66 -- -- RLOSMAX RLOS maximum I 65 -- -- RLOSTHR RLOS threshold I -- 88 88 RLOSMAX1 Channel 1 RLOS max I -- 87 87 RLOSTHR1 Ch 1 RLOS threshold I -- 37 66 RLOSMAX2 Ch 2 RLOS max I -- 38 65 RLOSTHR2 Ch 2 RLOS threshold I -- -- 37 RLOSMAX3 Ch 3 RLOS max I -- -- 38 RLOSTHR3 Ch 3 RLOS threshold I 64 -- -- RLOSMDIS RLOS data mute disable I -- 86 86 RLOSMDIS1 Ch 1 RLOS data mute disable I -- 39 64 RLOSMDIS2 Ch 2 RLOS data mute disable I RLOSMDIS3 Ch 3 RLOS data mute disable I -- 1-8 -- 39 Mindspeed TechnologiesTM LOS Threshold Control pins. RLOSMAX and RLOSTHR select the trip level and hysteresis level of the comparator. See Table 2-3 for the Threshold Value settings. Disable RLOS Data Mute on RLOS detection. RLOSMDIS = 0 to enable auto-data squelch upon RLOS. RLOSMDIS = 1 for no data squelch upon RLOS. 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (5 of 9) Pin # Signal Name Description I/O/P Notes M28331-3x M28332-3x M28333-3x Control Signals 74 74 74 ENDECDIS Encoder/decoder disable (for all channels) I For testing purposes and in applications where the decoder needs to be bypassed, the decoder can be enabled/disabled as follows: 1 = Dual rail pulse coded data format. Input transmit data pins TPOS, TNRZ, TNEG and NC are interpreted as TPOS and TNEG (encoded positive and negative rail data). Output receive data pins RPOS and RNRZ, and RNEG and RLCV are interpreted as RPOS and RNEG, with RPOS having a positive pulse in place of every positive AMI pulse and RNEG having a negative pulse in place of every negative AMI pulse. 0 = NRZ format. Transmit data pins TPOS and TNEG are interpreted as TNRZ and NC (not connected). Receive data pins RPOS and RNEG are interpreted as RNRZ and RLCV. In this mode, all line code violations are reported as active high on RLCV. 63 -- -- TAIS -- 76 76 TAIS1 -- 49 63 -- -- 53 53 28333-DSH-003-A Transmit Ch1 AIS mode enable I TAIS2 Transmit Ch2 AIS mode enable I 49 TAIS3 Transmit Ch3 AIS mode enable -- 53 E3MODE E3MODE I Mindspeed TechnologiesTM Transmission of Alarm Indication Signal (AIS) for a given channel. Replace transmit data with AIS signal. The AMI form of AIS supported is alternating 1s. (+1, -1, +1, -1, +1, ...) AIS will overwrite data during local loopback. 1 = AIS mode enabled 0 = AIS mode disabled When the pin is set to high, it enables the E3 mode on all channels, instead of the DS3/STS-1 mode. This also changes the pulse shaper to E3 mode and overrides all LBO pins. It also changes the encoder/decoder from B3ZS mode to HDB3 mode. 1 = E3 mode 0 = DS3/STS-1 mode 1-9 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (6 of 9) Pin # Signal Name Description I/O/P Notes Transmit line Ch1 build-out mode I Line build-out mode per channel, based on the length of cable on the transmit side of the cross-connect block. This bit is overridden and the pulse shaper is disabled (no pulse shaping) if E3MODE = 1. M28331-3x M28332-3x M28333-3x 55 -- -- LBO -- 91 91 LBO1 -- 34 55 LBO2 Transmit line Ch2 build-out mode I -- -- 34 LBO3 Transmit line Ch3 build-out mode I 1 = Inserts line build-out into the transmit channel. Usually used when the transmit cable is less than 450 feet in length. 0 = Line build-out bypassed (not inserted). Usually used when the transmit cable is greater than 450 feet in length. 1-10 71 -- -- LLOOP Local loopback enable Ch1 I LLOOP2 Local loopback enable Ch2 I Local loopback enable per channel. The transmit data is looped back immediately from the encoder to the decoder in place of the received data. -- 93 93 LLOOP1 -- 32 71 -- -- 32 LLOOP3 Local loopback enable Ch3 I 1 = local loopback enabled 0 = local loopback disabled 72 -- -- RLOOP I -- 94 94 RLOOP1 Remote loopback enable Ch1 -- 31 72 RLOOP2 Remote loopback enable Ch2 I Remote loopback enable per channel. The receive data, retimed after clock recovery, is looped back into the AMI generator in place of the transmit data. 1 = remote loopback enabled 0 = remote loopback disabled -- -- 31 RLOOP3 Remote loopback enable Ch3 I 56 -- -- XOE I Transmit output enable per channel. -- 90 90 XOE1 Transmit output enable Ch1 -- 35 56 XOE2 Transmit output enable Ch2 I 1 = transmit line output driver enabled 0 = transmit output driver set to high impedance state -- -- 35 XOE3 Transmit output enable Ch3 I Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (7 of 9) Pin # Signal Name Description I/O/P Notes Ch1 Receive High EQ Gain Enable I The equalizer in the M2833i has two gain settings. The higher gain setting is designed to optimally equalize a nominally-shaped (meets the pulse template), pulse-driven DS3 or STS-1 waveform that is driven through 0-900 feet of cable. Square-shaped pulses such as E3 or DS3-HIGH require less high-frequency gain and should use the low EQ gain setting. M28331-3x M28332-3x M28333-3x 57 -- -- REQH -- 89 89 REQH1 -- 36 57 REQH2 Ch2 Receive High EQ Gain Enable I -- -- 36 REQH3 Ch3 Receive High EQ Gain Enable I REQH = 1 high EQ gain (DS3/STS-1 modes) REQH = 0 low EQ gain (E3/DS3 Square Modes) Power/Ground 15 -- -- TVDD TX power Ch1 P 5 5 TVDD1 -- 25 15 -- -- 10 TVDD2 TX power Ch2 P 25 TVDD3 TX power Ch3 P -- -- TVSS TX ground Ch1 P -- 100 100 TVSS1 -- 20 10 TVSS2 TX ground Ch2 P -- -- 20 TVSS3 TX ground Ch3 P 16 -- -- RVDD RX power Ch1 P -- 6 6 RVDD1 -- 26 16 RVDD2 RX power Ch2 P -- -- 26 RVDD3 RX power Ch3 P 19 -- -- RVSS RX ground Ch1 P -- 9 9 RVSS1 -- 29 19 RVSS2 RX ground Ch2 P -- -- 29 RVSS3 RX ground Ch3 P 75 75 75 DVDDC Digital core power P Digital core power for all channels (3.3 V). 51 51 51 DVSSC Digital core ground P Digital core ground for all channels. 98 98 98 VGG 5 V/3.3 V ESD pin (1) P 5 V supply for 5 V-tolerant, digital pad ESD diodes. No static power is drawn from pin. 92 92 92 DVDDIO Digital I/O power P Connect to 3.3 V digital power. 33 33 33 DVSSIO Digital ground P Digital ground. 5, 6, 25, 26 15, 16 -- VDD Power P Connect to 3.3 V power. 28333-DSH-003-A Mindspeed TechnologiesTM Power pins for transmit circuitry per channel (3.3 V). Ground pins for transmit circuitry per channel. Power pins for receive circuitry per channel (3.3 V). Connect to 3.3 V power. Ground pins for receive circuitry per channel. Connect to ground. 1-11 M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (8 of 9) Pin # Signal Name Description I/O/P Notes M28331-3x M28332-3x M28333-3x 9, 20, 29, 100 10, 19 -- VSS Ground P Connect to ground. Power down for Ch1 I Power down transceiver channel 0 = Power down channel (off) 1 = Channel active (on) Power down for Ch2 I Miscellaneous 1-12 73 -- -- PD -- 95 95 PD1 -- 30 73 PD2 -- -- 30 PD3 Power down for Ch3 I Note: A special power-down mode exists when all three PDBs are set low. This special mode shuts off the entire chip (including biasing). 58 -- -- REFCLK I Reference clock from off-chip. -- 81 81 REFCLK1 Reference clock for Ch1 -- 44 58 REFCLK2 Reference clock for Ch2 I -- -- 44 REFCLK3 Reference clock for Ch3 I 99 99 99 RBIAS Bias resistor O A 12.1 k 1% resistor tied from this pin to ground provides the current reference to the entire chip.(2) 97 97 97 Reset Reset I Asynchronous reset (reset entire device). 96 96 96 GPD Global Power down I Power down (Static Idd testing). 0 = Power down disable 1 = Power down active Mindspeed TechnologiesTM This clock should be set to one of the following with all rates = 20 ppm tolerance: * E3 rate (34.368 MHz) * DS3 rate (44.736 MHz) * STS-1 rate (51.84 MHz) The clock rate should correspond to the mode of operation that has been chosen for the channel. See Section 2.5.2, Power-On Reset, about the valid clock available during power-up. 28333-DSH-003-A M28331/M28332/M28333 (-3x) 1.0 Pin Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 1.1 Pin Assignments Table 1-1. M2833i-3x Pin Definitions (9 of 9) Pin # Signal Name Description I/O/P Notes M28331-3x M28332-3x M28333-3x 11 -- -- TMONP Ch1 positive input I -- 1 1 TMON1P 14 -- -- TMONM Ch1 negative input I -- 4 4 TMON1M -- 21 11 TMON2P Ch2 positive input I -- 24 14 TMON2M Ch2 negative input I -- -- 21 TMON3P Ch3 positive input I -- -- 24 TMON3M Ch3 negative input I 59 -- -- TLOS O -- 80 80 TLOS1 TX loss of signal Ch1 Output -- 45 59 TLOS2 TX loss of signal Ch2 Output O -- -- 45 TLOS3 TX loss of signal Ch3 Output O 54 54 54 TMONTST TX monitor test pin I 1-4, 7, 8, 21-24, 27, 28, 30-32, 34-50, 52, 76-91, 93-95 11-14, 17-18, 50, 52, 55-73 50, 52 -- No connect -- Transmit monitor input pins are normally tied to their respective transmit line outputs, i.e., (TMON1P TLINE1P and TMON1M TLINE1M). Loss of signal outputs are active high when the monitor inputs detect no signal. The TX monitor test pin will assert all TLOS outputs when TMONTST is high. This is used to test board level functionality downstream from the TLOS outputs. Not connected. NOTE(S): (1) This pin should be connected to 3.3 V in an all-3.3 V design. Placing a capacitor from this pin to ground may result in instabilities. 3. All digital input pins contain a 75 k pull-down resistor from input to DVSS. (2) 28333-DSH-003-A Mindspeed TechnologiesTM 1-13 M28331/M28332/M28333 (-3x) 1.0 Pin Description 1.1 Pin Assignments 1-14 Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit Mindspeed TechnologiesTM 28333-DSH-003-A 2 2.0 Functional Description 2.1 Overview The M28333 is a triple E3/DS3/STS-1 Line Interface Unit (LIU). It is the physical layer interface between the data framer (or other terminal-side equipment) and the electrical cable used for data transmission. The M28333 LIU consists of three independent data transceivers that can operate over type 734/728 coaxial cable at the rates of 34.368 Mbps (E3), 44.736 Mbps (DS3), and 51.84 Mbps (STS-1). The transmit side takes an NRZ or already-encoded dual rail input and encodes it into AMI B3ZS (for DS3/STS-1) or HDB3 (for E3) analog waveforms to be transmitted over 75 coaxial cable. The receiver side takes in the attenuated and distorted analog receive signal and equalizes, slices, and resynchronizes the signal before decoding it to the NRZ output or sending out a non-decoded dual rail. M28331 and M28332 are single- and dual-E3/DS3/STS-1 LIUs, respectively. In all respects, their performance and features are identical to the M28333. The architecture of the M2833i includes the following internal functions for each channel: Transmitter: * * * * * AMI B3ZS/HDB3 encoder pulse shaper line driver Alarm Indication Signal (AIS) insertion transmit monitor Receiver: * * * * * * * 28333-DSH-003-A receive sensitivity Automatic Gain Control (AGC) receive equalizer Clock Recovery circuit Loss Of Signal (LOS) detector B3ZS/HDB3 decoder with bipolar violation detector data squelching Mindspeed TechnologiesTM 2-1 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.1 Overview Additional Functions: * * * bias generator power-on reset loopback MUXes In addition, each channel has the ability to perform remote and local loopbacks. Figure 2-1 illustrates a typical application using the M2833i in a channel. External pins are provided to configure the various line rates and formats for each channel. The M2833i is used as a data transceiver over a coaxial cable that is up to 900 feet long (or up to 450 feet from the DSX) in an on-premise environment within any public or private networks which use these data rates. Figure 2-1. Typical Application Of Single M2833i Channel TX RX 0-450 ft COAX (type 734/728) 0-450 ft COAX (type 734/728) DSX 0-450 ft COAX (type 734/728) DSX 0-450 ft COAX (type 734/728) RX TX 100604_012 2-2 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter 2.2 Transmitter This section describes the detailed operation of the various blocks in the M2833i transmitter. 2.2.1 AMI B3ZS/HDB3 Encoder The ENDECDIS and E3MODE pins configure the encoder mode. When ENDECDIS = 0, the encoder is receiving non-encoded Nonreturn to Zero (NRZ) data on the TNRZ (TPOS) pin alone, and the NC (no connect) (TNEG) pin is ignored. Data is encoded into a representation of a three-level B3ZS (E3MODE = 0) or HDB3 (E3MODE = 1) signal before going on to the pulse shaper in the form of two binary signals representing the positive and negative three-level pulses. When ENDECDIS = 1, the encoder is disabled. The encoder passes already-encoded data over TPOS (TNRZ) and TNEG (NC) to the pulse shaper. The transmit digital data is clocked into the chip via a rising TCLK edge, which must be equal to the symbol rate (line rate). A small delay added to the data provides a certain amount of negative data hold time. 2.2.2 Pulse Shaper The pulse shaper converts the two digital (clocked) positive and negative pulses into a single analog three-level Alternate Mark Inversion (AMI) pulse. The pulses are in Return to Zero (RZ) format, meaning that all positive and negative pulses have a duration of the first half of the symbol period. For the E3 rate (E3MODE = 1), the AMI pulse is a full-amplitude, square-shaped pulse with very little slope. Figure 2-2. Pulse Shaper E3 Mode + Pulse - Pulse LBO LBO = 0 Pulse Shaper Line Driver LBO = 1 500020_010 28333-DSH-003-A Mindspeed TechnologiesTM 2-3 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter For DS3/STS-1 rates, a pulse-shaper block is used to shape the transmit waveform and reduce its high-frequency energy content. This ensures that the transmit pulse template is met at the cross-connect block, which follows 0-450 feet of transmit-side coaxial cable. 2.2.3 Line Driver The differential line driver takes the filtered transmit waveform, increases it to the proper level, and drives it into the transmit magnetics. The two external discrete back-matching resistors (31.6 ) aid in line matching. The driver is presented with an approximately 150 differential load. Driver gain accounts for the 6 dB gain loss in the back-matching resistors. Figure 2-3 illustrates the Pulse/Power template measurement points for the various data rates. Figure 2-3. Pulse Measurement Points Pulse/Power Template for DS3/STS-1 TX 0-450 ft COAX (type 734/728) 0-450 ft COAX (type 734/728) DSX RX Pulse/Power Template for E3 RX 0-450 ft COAX (type 734/728) DSX 0-450 ft COAX (type 734/728) TX 100604_013 2.2.3.1 Transmit Pulse Mask Templates 2-4 The Transmit Pulse Mask characteristics of the M2833i device are designed so that the transmitted output meets the Pulse Shape mask specified in ITU-T Recommendation G.703. Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter Figure 2-4. Transmit Pulse Mask for DS3 Rates Transmit Pulse Mask for DS3 Rates 1.2 Normalized Pulse Amplitude 1 0.8 0.6 0.4 0.2 0 -0.2 1.5 1.0 0.5 0.0 -0.5 -1.0 Normalized Symbol Time NOTE(S): An Isolated Pulse is a pulse preceded by at least two zeros and followed by one or more zeros. In judging the conformance of an isolated pulse to the mask, it is permissable to do the following: 1. Position the mask horizontally as necessary to encompass the pulse 2. Uniformly scale the amplitude of the isolated pulse to fit the mask Table 2-1. DS3 Transmit Template Specifications Time Axis Range (UI)(1) Normalized Amplitude Equation Upper Curve -0.85 T -0.68 0.03 -0.68 T 0.36 0.03 + 0.5 {1 + sin [( / 2)(1 + T / 0.34)]} 0.36 T 1.4 0.08 + 0.407 e -1.84(T - 0.36) Lower Curve -0.85 T -0.36 -0.03 -0.36 T 0.36 -0.03 + 0.5{1 + sin[( / 2)(1 + T / 0.18)]} 0.36 T 1.4 -0.03 NOTE(S): (1) UI = 1 / (System Clock Frequency) 28333-DSH-003-A Mindspeed TechnologiesTM 2-5 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter Figure 2-5. Transmit Pulse Mask for STS-1 Rates Transmit Pulse Mask for STS-1 Rates 1.2 Normalized Pulse Amplitude 1 0.8 0.6 0.4 0.2 0 -0.2 1.5 1.0 0.5 0.0 -0.5 -1.0 Normalized Symbol Time NOTE(S): An Isolated Pulse is a pulse preceded by at least two zeros and followed by one or more zeros. In judging the conformance of an isolated pulse to the mask, it is permissable to do the following: 1. Position the mask horizontally as necessary to encompass the pulse 2. Uniformly scale the amplitude of the isolated pulse to fit the mask Table 2-2. STS-1 Transmit Template Specifications Time Axis Range (UI)(1) Normalized Amplitude Equation Upper Curve -0.85 T -0.68 0.03 -0.68 T 0.26 0.03 + 0.5 {1 + sin [( / 2)(1 + T / 0.34)]} 0.26 T 1.4 0.1 + 0.61 e -2.4(T - 0.26) Lower Curve -0.85 T -0.36 -0.03 -0.36 T 0.36 -0.03 + 0.5 {1 + sin[( / 2)(1 + T / 0.18)]} 0.36 T 1.4 -0.03 NOTE(S): (1) 2-6 UI = 1 / (System Clock Frequency) Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter Figure 2-6. Transmit Pulse Mask for E3 Rate 17 ns 0.2 0.1 0.1 14.55 ns 0.2 Volts 8.65 ns 1.0 12.1 ns 0.5 24.5 ns 0.1 0.2 0.1 29.1 ns Time 500118a_1 28333-DSH-003-A Mindspeed TechnologiesTM 2-7 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter 2.2.4 Alarm Indication Signal (AIS) Generator When TAIS is asserted, an AIS replaces the transmit data at TPOS and TNEG. The E3 type of AIS signal (all 1s) is supported. In three-level signal form, this is a continuously alternating positive and negative pulse stream, as if the transmit data were a continuous string of logical 1s. Figure 2-7 illustrates the AIS signal. The TAIS pin has the same data latency as the TX data pins and can be used to replace single symbols within a data stream. When the encoder is disabled (ENDECDIS = 1), the TAIS mode maintains the proper phase, based upon the polarity of the last 1 received. The AIS overwrites data during local loopback operation, it does not affect remote loopback operation. Figure 2-7. AIS Signal POSITIVE PULSE NEGATIVE PULSE TLINEP (output voltage) TLINEN (output voltage) 8333_009 2-8 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.2 Transmitter 2.2.5 Transmit Monitor Block The Transmit (TX) Monitor pins allow the M2833i to monitor for certain fault condition occurrences such as short circuits or defective channel output drivers in the device. The TX Monitor inputs (TMONP and TMONM) are independent functions where TMONP and TMONM must be externally connected (via 0- resistors or directly) to the TLINEP and TLINEM/N pins. The TX monitors are designed to monitor the line driver outputs for pulses greater than the threshold of 0.5 V and to assert a Loss Of Signal (TLOS) indicator when no output pulse has been detected for 32 TCLK periods. When the TMONP/TMONM pins are connected, the TX Monitor circuitry only responds to a voltage difference between the pair, i.e., if TLINEP stops working but TLINEM/N is still swinging 1 V, the TX Monitor circuit reports a Not Asserted status. After a TLOS condition is asserted, it will not deassert until a pulse is again detected. TLOS Output pins are active-high when the monitor inputs do not detect a signal. A special pin (TMONTST) is available for testing board-level functionality downstream from the TLOS outputs. When TMONTST is high, it asserts all TLOS channel outputs. Other typical TMON circuit applications are for transmitter device redundancy. This is where the TX monitor of one device is used to monitor a second active device. When the TMON circuit detects an output driver failure, it asserts a TLOS, which can now be used to activate the second device's transmitter and output disable the primary device. 2.2.6 Jitter Generation (Intrinsic) The M2833i device meets the jitter generation requirements for various rates with large margins, with the condition that the input transmit clock (TCLK) is jitter-free. Data rates and jitter generation requirements are defined in the following documents: * * * 28333-DSH-003-A E3 rate--ETSI TBR24, ITU-T G.823 DS3 rate--Bellcore GR499, AT&T Accunet TR54014, ITU-T G.824 STS-1 rate--Bellcore GR253 Mindspeed TechnologiesTM 2-9 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.3 Receiver 2.3 Receiver This section describes the detailed operation of the various blocks in the M2833i receiver. 2.3.1 Receive Sensitivity The receiver recovers data from the coaxial cable that is attenuated due to the frequency-dependent characteristics of the cable. In addition, the receiver compensates for the flat loss (across all frequencies) in the various electrical components and the variation in transmitted signal power. The M2833i device is able to recover data that has been attenuated by a maximum of 900 feet of coax having characteristics and attenuation consistent with ANSI T1.102-1993, Annex C, Figure C.2. This approximates the characteristics of AT&T type 734/728 cable; almost the same attenuation characteristic is achieved by one-half the length of AT&T type 735 cable. 2.3.2 AGC/VGA Block The Variable Gain Amplifier (VGA) receives the AMI input signal from the coaxial cable. The VGA supplies flat gain (independent of frequency) to make up for various flat losses in the transmission channel and for loss at one-half the symbol rate that cannot be made up by the equalizer. The VGA gain is controlled by a feedback loop which senses the amplitude of the equalizer output, acting to servo this amplitude for optimal slicing. 2.3.3 Receive Equalizer The receive equalizer receives the differential signal from a VGA and boosts the high frequency content of the signal to reduce intersymbol interference (ISI) to the point that correct decisions can be made by the slicer with a minimum of jitter in the recovered data. The REQH pin when set high (REQH = 1) boosts the amount of equalization in the receive side of the LIU. DS3/STS-1 pulses require a greater amount of equalization then standard E3 pulses. REQH is therefore normally set high (REQH = 1) for standard DS3/STS-1 pulses. For cases where a square-shaped DS3/STS-1 pulse (that does not meet the DS3/STS-1 standards) is transmitted to the receiver REQH can be set low (REQH = 0). In E3 mode, the REQH pin should always be set low (REQH = 0) to prevent over-equalization. 2-10 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.3 Receiver 2.3.4 The PLL Clock Recovery Circuit The clock recovery circuit (RX PLL) extracts the embedded clock from the sliced data and provides this clock and the retimed data to the decoder (data mode). Upon startup (after the internal reset is deasserted), the RX PLL uses a reference clock (REFCLK) and a phase-frequency detector to lock to the correct data rate (reference mode). During reference mode, the data outputs are squelched (set to 0). The RX PLL is kept in reference mode until a valid input is detected. 2.3.5 Receive Loss Of Signal (RLOS) Detector The RLOS detector circuitry consists of 2 functional blocks: the analog section and the digital. The analog section consists of high-speed, low-offset comparators used for amplitude qualification. The digital block qualifies the pulse stream 1s density and zero run length. Two control pins, RLOSMAX and RLOSTHR, select the trip and hysteresis comparator levels for each channel (see Table 2-3). Table 2-3. RLOS Threshold Settings RLOSMAX RLOSTHR 0 0 0 1 1 x Min (mV) Typical (mV) Max (mV) RLOS Cleared -- 55 125 RLOS Declared 18 20 -- RLOS Cleared -- 92 -- RLOS Declared -- 58 -- Test Mode -- -- -- Action A control pin for each channel, RLOSMDIS, is used as follows to decide if RLOS should disable data squelching: RLOSMDIS = 0 for auto data squelch RLOSMDIS = 1 for no data squelch The digital block asserts RLOS when no valid pulses (per the analog section described above) have been received for 128 REFCLKs. The digital block clears the RLOS when the valid pulse density exceeds 20.3% with less than 64 consecutive zeros during an 128-symbol period. 2.3.6 B3ZS/HDB3 Decoder With Bipolar Violation Detector In the M2833i device, when ENDECDIS = 0 (encoder/decoder enabled), the decoder takes the output from the clock recovery circuit and decodes the data (HDB3 or B3ZS) into a single retimed NRZ data signal. The data signal is then sent out of the M2833i over the RNRZ (RPOS) pin. Any detected Line Code Violations (LCV) are sent out over the corresponding RLCV (RNEG) pin. The RLCV pin is asserted for one symbol period at the time the violation appears on the RX output pin (RNRZ). 28333-DSH-003-A Mindspeed TechnologiesTM 2-11 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.3 Receiver The following shows data sequence criteria for LCV; violations are indicated in bold text. A valid bipolar pulse is indicated by a B. A bipolar violation (non-alternating positive or negative) pulse is indicated by a V. * * * Excessive zeros: 0, 0, 0, 0 (HDB3) or 0, 0, 0 (B3ZS). These violations are passed on as 0 data on the RNRZ pin. Bipolar violation: B, 0, V (i.e., +1, 0, +1 or -1, 0, -1 for HDB3) B, V (B3ZS and HDB3). These violations are passed on as 1 data on the RNRZ pin. Coding violation: 0, 0, V (HDB3) or 0, V (B3ZS) with an even number of Bs since the last valid 0 substitution V (follows coding rule). These violations are passed on as 0 data on the RNRZ pin. The even/odd counter (used to count the number of Bs between Vs) will count a bipolar violation as a B. A coding violation or a valid 0 substitution resets the counter. When ENDECDIS = 1, the decoder is disabled, and the retimed slicer outputs are sent out over RPOS (RNRZ) and RNEG (RLCV) pins. These outputs are then decoded by the Framer or other downstream device. Line code violations are not detected in this mode of operation. The decoder is configurable for either: * * E3 mode using HDB3 coding (E3MODE = 1) DS3/STS-1 mode using B3ZS coding (E3MODE = 0) The receiver digital data outputs are centered on the rising edge of RCLK (see Section 2.9). 2.3.7 Data Squelching A counter in the receiver keeps track of the number of consecutive symbol periods without a valid data pulse. When 128 or more 0s in a row are counted, the receiver assumes that it has lost the signal and resets itself to try and regain the signal. While the receiver is reacquiring the signal, the clock recovery block locks to the reference clock and the data squelching is achieved by forcing the data bits to zero. The data squelching is true in both NRZ and dual rail mode. When the input signal has been properly amplified and equalized, the clock recovery PLL will then switch to the incoming data. 2-12 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.4 Jitter Tolerance 2.4 Jitter Tolerance The M2833i receiver is able to tolerate a specified amount of high-frequency jitter in the received signal while providing error-free operation (generally defined as a bit error rate of less than 10-9). The specifications (illustrated in Figure 2-9) for jitter tolerance are discussed in the following documents: * E3 rate--ITU-T G.823 and ETSI TBR24 contain frequency masks for input jitter tolerance. NOTE: To meet jitter transfer requirements for loop-timed operation, an external jitter attenuator is required. The jitter attenuator lessens jitter from the receive clock. * DS3 rate--Bellcore GR499 specifies jitter tolerance frequency masks for Category I and Category II interfaces. * STS-1 rate--Bellcore GR253 specifies jitter tolerance. It is noted that the STS-1 jitter tolerance differs from DS3 requirements only for Category II interfaces. Figure 2-8. Minimum Jitter Tolerance Requirement Receiver Jitter Tolerance 10 UI T3 [GR-499 (1995)] 10 Category II 5 CX28333 Jitter Tolerance Input Jitter Amplitude T3 [GR-499 (1995)] Category I E3 [GR.823 (1993)] 1.5 1.0 UI 0.3 0.15 0.1 0.1 UI 10 Hz 100 Hz 2.3K 1 kHz 22.3K 10 kHz 60K 300K 100 kHz 800K 1 MHz Jitter Frequency (Hz) 100604_014 28333-DSH-003-A Mindspeed TechnologiesTM 2-13 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.4 Jitter Tolerance 2.4.1 Jitter Transfer The receiver must meet certain jitter transfer specifications between the input and output jitter as a function of frequency. These specifications are only intended to be met with the use of a jitter attenuator. Because the M2833i does not contain a jitter attenuator, one will have to be supplied externally. For reference purposes, the specifications are discussed in the following documents and shown in Figure 2-9. E3 rate--Assume the same as DS3. DS3 rate--Bellcore GR499, section 7.3.2 and figures 7-3, 7-4, and 7-5, defines and describes DS3 jitter transfer. STS-1 rate--Bellcore GR253, section 5.6.2.1, defines and describes jitter transfer for the STS-1 rate. Figure 2-9. Maximum Jitter Transfer Curve Requirement Jitter Gain 0.1 dB -19.9 dB STS-1 Category II (Note: All slopes are 20 dB/decade) DS3 Category I DS3 Category II 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz Jitter Frequency 100985_012 2-14 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.5 Additional M2833i Functions 2.5 Additional M2833i Functions 2.5.1 Bias Generator To achieve good isolation between the channels, each channel utilizes an independent power and ground to both transmit and receive. Additionally, each channel has its own band gap voltage reference. Because only one external resistor for current generation exists, only one band gap voltage can be used. The band gap from Ch1 has been chosen for this task. The 12.1 k external resistor from pin RBIAS to ground, is specified to have a tolerance of 1%. This helps to keep tighter control on power dissipation and circuit performance. NOTE: Capacitance should be kept to a minimum on the RBIAS pin. 2.5.2 Power-On Reset (POR) If the system cannot guarantee a valid REFCLK frequency input during the POR cycle, the M2833i devices require assertion (active-high input pulse width, 1 s minimum) of the external reset signal (RESET, Pin 78 [80-pin package], Pin 97 [100-pin package]). Valid operation frequencies are DS3 (44.768 MHz 20 ppm), E3 (34.368 MHz 20 ppm), and STS-1 (51.84 MHz 20 ppm). See the M28331/2/3-3x Evaluation Module User Guide for crystal oscillator specifications and vendor listings. A POR circuit is provided in the M2833i device to initialize all resettable digital logic and analog control lines. The POR circuit uses a fixed RC timer (~1s) to deassert itself when the power supply voltage reaches a minimum level (~2 V). When the minimum supply voltage is reached (see Table 2-6), the REFCLK input is counted for 128 clocks before the internal reset is deasserted. At this time, the receiver block attempts to frequency lock (5% tolerance) onto a valid incoming REFCLK input. After frequency lock is achieved, the receiver attempts to phase lock onto the valid RLINE receive signal. NOTE: If a valid REFCLK input is not present when POR releases the internal reset, the receiver block may be unable to lock to the RLINE receive signal. It is common for some crystal oscillator types oscillate at a lower fundamental frequency if the crystal oscillator supply has not reached its minimum operation voltage. 2.5.3 Loopback Multiplexers (MUXes) Two loopback MUXes per channel in the M2833i allow for local loopback (terminal or framer side), remote loopback (cable side), or both. The RLOS signal monitors the RX cable inputs irrespective of any loopback. In remote loopback, set by asserting pin RLOOP high, the receive data (retimed after clock recovery but not decoded) loops back into the pulse shaper in place of the transmit data. Additionally, this data is sent out the RPOS, RNEG, and RCLK pins. 28333-DSH-003-A Mindspeed TechnologiesTM 2-15 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.5 Additional M2833i Functions In local loopback, set by asserting pin LLOOP, the transmit data loops back immediately from the encoder output to the decoder input in place of the received data. Additionally, this data is sent out the TLINEP and TLINEM/N pins. Figures 2-10 and 2-11 illustrate remote and local loopback flow. NOTE: Transmit AIS operation overwrites data with an all 1's pattern during local loopback, it does not affect remote loopback operation. Figure 2-10. Remote Loopback XOE LBO E3MODE PDB PDATA/ NDATA TPOS TNEG TCLK TLINEP Pulse Shaper Encoder LINE DRIVER TLINEM/N TCLK TAIS RLOOP LLOOP DATA MUX ENDECDIS TX Monitor RPOS TXMON TMONTST REFCLK RLOS P PDATA RNEG NDATA RCLK DECODER TMONP TMONM DATCLK Clock/ Data Recovery N Receiver ALOS RLINEP RLINEM/N REQH RLOSMAX RLOSTHR RLOSMDIS 2-16 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.5 Additional M2833i Functions Figure 2-11. Local Loopback XOE LBO E3MODE PDB PDATA/ NDATA TPOS TNEG TCLK TLINEP Pulse Shaper Encoder LINE DRIVER TLINEM/N TCLK TAIS RLOOP LLOOP DATA MUX ENDECDIS TX Monitor RPOS TXMON TMONTST REFCLK PDATA RNEG NDATA RCLK DATCLK RLOS TMONP TMONM P Clock/ Data Recovery DECODER N Receiver ALOS RLINEP RLINEM/N REQH RLOSMAX RLOSTHR RLOSMDIS 28333-DSH-003-A Mindspeed TechnologiesTM 2-17 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.6 Mechanical Specifications 2.6 Mechanical Specifications Figure 2-12. M2833i-3x Mechanical Drawing (100-Pin)--Dimensions D D 1 D 2 Pin #1 Ref. Mark D D D1 D2 D1 e 3 D3 b TOP BOTTOM Millimeters Dim. See DETAIL B A A A1 2 c L DETAIL B L1 Min. Max. Inches Min. Max. A A1 A2 D D1 D2 1.20 MAX. 0.05 0.15 0.95 1.05 15.75 16.25 13.90 14.10 D3 L L1 b e c Coplanarity 8.00 REF. 0.45 0.75 0.315 REF. 0.018 0.006 1.00 REF. 0.22 REF. 0.50 REF. 0.09 0.20 0.039 REF. 0.009 REF. 0.020 REF. 0.004 0.008 12.00 REF. 0.08 MAX. 0.047 MAX. 0.002 0.006 0.004 0.041 0.620 0.640 0.547 0.555 0.472 REF. 0.003 MAX. Ref. 100-Pin ETQFP (GP00-D543)mm 100985_008a 2-18 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.7 Electrical Characteristics 2.7 Electrical Characteristics 2.7.1 Absolute Maximum Ratings Table 2-4. Absolute Maximum Ratings Symbol Parameter Min Max Unit DVDDC/ RVDD/ TVDD/ VDD/ VGG Power Supply Voltage -0.3 6 V VI Voltage on Any Signal Pin -1.0 VGG + 0.3 V V TST Storage Temperature -40 125 C TVSOL Vapor Phase Soldering Temperature (1 min.) -- 220 C JA Thermal Resistance (Still air, socketed) -- 40 C/W JA Thermal Resistance (Still air, soldered) -- 24 C/W -- 7.40 C/W -- 313 fits Jc FIT -- Failures in time at 89,000 device hours, temperature of 55 C, 0 failures. NOTE(S): 1. Stresses above those listed as absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions beyond those indicated in the other sections of this document is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 28333-DSH-003-A Mindspeed TechnologiesTM 2-19 2.0 Functional Description M28331/M28332/M28333 (-3x) 2.7 Electrical Characteristics Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.7.2 ESD Ratings Testing Method--The devices were subjected to ESD events at the rated voltage with both positive and negative polarities relative to each other pin or supply domain on the device. The given pin was then curve-traced to detect leaky or shorted ESD diodes. The criterion for passing is 3 devices that withstand voltage without any leaky pins or functional failures. Table 2-5. ESD Ratings Model Required Minimum Observed 1,000 V 2,000 V Machine 100 V 200 V Charged Device 400 V 700 V Human Body 2.7.3 Recommended Operating Conditions Table 2-6 specifies various operating conditions, power supplies, and the bias resistor. Table 2-6. Recommended Operating Conditions Parameter Conditions Min Nom Max Unit Power supply voltage (5%) DVDDC, RVDD, TVDD, VDD 3.135 3.3 3.465 V ESD voltage(1, 2) VGG 3.135 5 5.5 V External bias resistor Pin RBIAS to GND; 1% 11.98 12.1 12.22 k NOTE(S): (1) With 5 V logic input, VGG should be tied to 5 V. With 3.3 V logic input, VGG should be tied to 3.3 V. VGG must be equal or greater than the power supply voltage. (2) When VGG is operated at 5V, sequence VGG to DVDDC, RVDD, TVDD, and VDD as discussed in Appendix C:. 2-20 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.8 DC Characteristics 2.8 DC Characteristics Table 2-7. DC Characteristics Parameter Conditions Min Nom Max Unit Vih high threshold Digital inputs (Logic 1) 2.0 -- VGG + 0.3 V Vil low threshold Digital inputs (Logic 0) -0.3 -- 0.8 V Voh high threshold Digital outputs, Ioh = -4 mA 2.4 -- -- V Vol low threshold Digital outputs, Iol = 4 mA -- -- 0.4 V ILEAK (digital inputs/outputs) 0 V digital Vin VGG -10 -- 200 A ILEAK (analog inputs/outputs) -- -270 -- 270 A -- -- -- 10 pF RLINExP, RLINExM, TLINExP, TLINExM, TMONxP, TMONxM Input capacitance Load capacitance Digital outputs -- -- 15 pF RLine/TLine capacitance Maximum load -- -- 50 pF Transmit Monitor Input impedance TMONP, TMONM to 0.25 V 7.5 10 12.5 k Input voltage range TMONP, TMONM to ground 0 -- Vdd V Input pulse threshold (TMONP, TMONM) 0.4 0.5 0.6 V TLOS asserted Number of TCLKs with no input 30 32 34 # TSYM Power dissipation M28333 (-1x, -3x) Total chip(1) -- 0.83 1.0 W Power dissipation (M28332) Total chip -- -- 0.8 W Power dissipation (M28331) Total chip -- -- .450 W NOTE(S): 1. The digital inputs of M2833i are TTL 5 V compliant when VGG = 5V. These inputs are diode protected to the VGG pin. Additionally, all of the M2833i digital inputs contain 75 k pull-down resistors. 2. The digital outputs of M2833i are also TTL 5 V compliant when VGG = 5V. However, these outputs do not drive to 5 V, nor do they accept 5 V external pull-ups. FOOTNOTE: (1) Measured while transmitting and receiving all-1s pattern. 28333-DSH-003-A Mindspeed TechnologiesTM 2-21 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.9 AC Characteristics 2.9 AC Characteristics Table 2-8. AC Characteristics (Logic Timing) Parameter Conditions Min Nom Max Unit Tosym, Tisym RCLK and TCLK E3 (34.368 MHz) DS-3 (44.736 MHz) STS-1 (51.84 MHz) -- 29.10 22.35 19.29 -- ns ns ns Clock Duty Cycle Towidth/Tosym, RCLK Tiwidth/Tisym, TCLK Tiwidth/Tisym, REFCLK 45 40 40 -- 55 60 60 % % % -- -- -- 3 ns Todelay Tisetup TPOS/TNRZ, TNEG, TAIS 4 -- -- ns Tihold TPOS/TNRZ, TNEG, TAIS 0 -- -- ns NOTE(S): 1. The description applies to the DS3, E3, and STS-1 clock rates and other parameters such as pulse width, set-up time, hold time, and duty cycle. 2. The timing diagram, illustrated in Figure 2-13, describes the logical relationship between various clock and data signals, and parameter values. 3. Todelay is measure with a 10-15 pF loading characteristic. 2-22 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.9 AC Characteristics Figure 2-13. Timing Diagram Tosym DATA OUTPUTS RCLK Towidth Todelay RPOS/RNRZ, RNEG/RLCV Tisym DATA INPUTS Tiwidth TCLK Tisetup TPOS/TNRZ, TNEG, TAIS, Don't Care Tihold Valid Data Don't Care 100604_016 28333-DSH-003-A Mindspeed TechnologiesTM 2-23 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.10 Transceiver Specification Tables 2.10 Transceiver Specification Tables Table 2-9. Receiver Specifications Parameter Conditions Min Nom Max Units -- 1.9 -- V Input common mode voltage Internal Bias (RLINEP, RLINEM) Receiver Sensitivity (RLINEP-RLINEM) DS3/E3/STS-1 17.5 -- -- mVpeak Diff. Cable reach AT&T-type 728/734 cable 900 -- -- feet Input return loss (at cable interface using recommended ext. components) 860-1,720 kHz 1,720-34,368 kHz 34,368-51,550 kHz 12 18 14 22 24 26 -- dB RLOS asserted Number of consecutive 0s 127 128 129 Symbols 1s density threshold (RLOS deasserted) 128 1 pulses with less than 64 consecutive zeros 20.1 20.3 20.5 % 2-24 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.10 Transceiver Specification Tables Table 2-10. Transmitter Specifications Parameter Conditions Min Nom Max Units 6 8 8 20 20 14 -- dB 1.0 0.97 0.80 0.95 0.78 1.1 Vpeak 0.85 Output return loss (at cable interface using recommended ext. components) 860-1,720 kHz 1,720-34,368 kHz 34,368-51,550 kHz Output amplitude using test setup in Figure 2-14. E3MODE = 1, E3 rate E3MODE = 0, LBO = 0, DS3 rate E3MODE = 0, LBO = 1, DS3 rate E3MODE = 0, LBO = 0, STS-1 rate E3MODE = 0, LBO = 0, STS-1 rate 0.9 Pulse Symmetry (Positive/Negative pulse amplitude ratio) E3MODE = 1, E3 rate All other modes 0.95 0.9 1.0 1.0 1.05 1.1 V/V Input impedance TMONP, TMONM 7.5 10 12.5 k Input voltage range TMONP, TMONM to ground 0 -- TVDD V Input pulse threshold (TMONP - TMONM) 0.3 0.5 0.7 V TLOS asserted Number of TCLKs with no input pulse 30 32 34 NOTE: Does not include ext. component variation. 0.85 # TSYM Figure 2-14. Test Setup for Measurement of Output Pulse Amplitude TMONP TLINEP 31.6 TX 75 TLINEM 31.6 1:1 TMONM 28333-DSH-003-A Mindspeed TechnologiesTM 2-25 M28331/M28332/M28333 (-3x) 2.0 Functional Description Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 2.10 Transceiver Specification Tables Table 2-11. Intrinsic Jitter Specifications (Receiver to Transmitter using Remote Loopback) Parameter Conditions Min Nom Max Units DS3 Wideband 10 Hz-400 kHz 0.010 0.003 UI peak-peak UI rms DS3 Narrowband 30 kHz-400 kHz 0.002 0.001 UI peak-peak UI rms E3 Wideband 10 Hz-800 kHz 0.060 0.007 UI peak-peak UI rms E3 Narrowband 10 kHz-800 kHz 0.056 0.007 UI peak-peak UI rms 2-26 Mindspeed TechnologiesTM 28333-DSH-003-A 3 3.0 Applications The M28331/M28332/M28333 can be used in a variety of applications. Figure 3-1 illustrates an example of three DS3 lines being terminated by the M28333. The data and clock are extracted and passed on to the framer chip for further data manipulation and user interface. It is important to employ high-frequency design techniques for the printed board layout. 3.1 PCB Design Considerations for the M2833i The M28333 is a mixed signal triple-port LIU device operating at frequencies up to 51.84 MHz. This calls for a careful design of the PCB layout. Some design considerations are outlined below. 3.1.1 Power Supply and Ground Plane A single power plane with bulk capacitors (typically 10 f) distributed throughout the board will mitigate most power rail-related voltage transients. A bulk capacitor should also be placed where the power enters the board. It is recommended that decoupling capacitors be routed directly to each of the power pins. It is recommended that 0.1 f, 0.01 f, and 0.001 f decoupling capacitors be used. All three values are not required on each pin, but values should be dispersed uniformly to filter different frequencies of noise. 10 f tantalum capacitors should be placed on all four corners of the chip. A continuous ground plane is the best way to minimize ground impedance. Most ground noise is produced by the return currents and power supply transients during switching. This effect is minimized by reducing the ground plane impedance. 3.1.2 Component Placement 3.1.2.1 RBIAS Resistor 28333-DSH-003-A It is important to keep the RBAIS pins quiet, as any noise coupled to these pins affect the internal references. The RBIAS resistors should be placed as close as possible to the RBIAS pins and no digital signals should be routed near the pins or the resistors. It is recommended to guard the pin, resistor, and traces with ground vias. Mindspeed TechnologiesTM 3-1 M28331/M28332/M28333 (-3x) 3.0 Applications 3.1 PCB Design Considerations for the M2833i Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 3.1.2.2 VGG Decoupling It is recommended that the VGG pin be decoupled with a 0.1 f, 0.01 F and 0.001 f capacitors. These capacitors should be placed close to the VGG pin. 3.1.2.3 Termination Resistors and Capacitors The termination resistors and capacitors on the receive RLINE pins should be placed as close the receiver input on the chip as possible. The series resistors for the transmit TLINE pins should also be placed as close to the transmitter output pins as possible, but are less of a priority then the RLINE. 3.1.3 Impedance Matching It is critical that both the transmit and receive traces around the transformers and the matching resistors be kept to a minimum length and that the trace impedance be matched to 75 ohms. The transmit signals between the device and the transformer should be routed 75 ohm differentially. The transmit signals should be routed single ended between the transformer and the BNC connector. The receive signals should be routed differentially between the transformers and either differentially or single ended from the transformers to the BNC connectors, depending on the application. If the application requires ground termination it is recommended that the signals be routed single ended. If the application does not require ground termination, then the signals can be routed differentially. To route signals differentially, the signal pair (positive and negative) should be 75 ohm coupled and should be surrounded by solid power/ground planes (buried strip line) or be coupled to a power/ground plane (microstrip). Buried strip line is recommended for internal layers while microstrip line is used for signals routed on surface layers. There should be no discontinuity in the planes during the path of the signal traces. Single ended signals should be 75 ohm coupled between power/ground planes for inner layers or 75 ohm coupled to a power/ground plane on the outer layers. There should be no discontinuities in the power/ground planes over the trace path. Impedance discontinuities occur when a signal passes through vias and travels between layers. It is recommended to minimize the number of vias and layers that the transmit/receive signals travel through in the design. 3.1.4 Other Passive Parts Mindspeed recommends the use of 1:1 transformers for coupling the BNC connectors to the device. The M28333 EVM uses six Pulse T3001 transformer devices to handle the 3 Tx and 3 Rx channels. It is recommended that a 220 F tantalum capacitor be used where the power enters the board. 3.1.5 IBIS Models IBIS (Input/Output Buffer Interface Specification) models for the M28331/M28332/M28333 are available from Mindspeed's web site (www.mindspeed.com). 3-2 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) 3.0 Applications Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 3.1 PCB Design Considerations for the M2833i 3.1.6 Recommended Vendors America Address: Telo: Fax: Northern Asia Telo: Northern Europe Telo: Fax: 28333-DSH-003-A Product: Transformers Product: Crystals Pulse Corporate Office 12220 World Trade Drive San Diego, CA 92128 858-674-8100 858-674-8262 Crystek Corp. 12730 Commonwealth Drive Fort Myers, FL 33913 800-237-3061 941-561-1025 sales@crystek.com www.crystek.com Telo: Fax: E-mail: Web site: Pulse 3F-4, No. 81, Sec. 1 Hsin Tai Wu Road Hsi-Chih Tapei Hsien, Taiwan R.O.C. 886-2-26980228 886-2-26980948 Pulse 1S2 Huxley Road The Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom 44-1483-401700 44-1483-401701 Mindspeed TechnologiesTM 3-3 M28331/M28332/M28333 (-3x) 3.0 Applications Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit 3.1 PCB Design Considerations for the M2833i Figure 3-1. DS3/E3 Application Diagram M28333 TMONP TPOS TNEG TCLK TLINEP TX TLINEN TMONM Framer Channel 1 RPOS RNEG RCLK Type 728, 734, 735 75 W 31.6 W 1:1 RLINEP RX RLINEN BIAS RESET 31.6 W 37.4 W 0.01 F 1:1 Type 728, 734, 735 75 W 37.4 W MODE TMONP TLINEP TPOS TNEG TCLK TX TLINEN TMONM Framer Channel 2 RPOS RNEG RCLK Type 728, 734, 735 75 W 31.6 W 1:1 RLINEP RX RLINEN BIAS RESET 31.6 W 37.4 W 0.01 F 1:1 Type 728, 734, 735 75 W 37.4 W MODE TMONP TLINEP TPOS TNEG TCLK TX TLINEN TMONM Framer Channel 2 RPOS RNEG RCLK Type 728, 734, 735 75 W 31.6 W 1:1 RLINEP RX RLINEN MODE BIAS RESET MODE BIAS RESET 31.6 W 37.4 W 0.01 F 1:1 Type 728, 734, 735 75 W 37.4 W 12.1 KW RBIAS Mode/Status Pins 100985_009 NOTE(S): 1. All transformers are part number T3001 from Pulse Technology. See Recommended Vendors, Section 3.1.6. 2. TMONP and TMONM are only available on the M2833i-3x device and are denoted by dotted lines. 3-4 Mindspeed TechnologiesTM 28333-DSH-003-A A Appendix A: Applicable Standards The applicable standards documents are as follows: * ANSI T1.102-1993 (DS3 and STS-1 standard) * ANSI T1.404a-1996 (DS3 metallic interface) * ITU Recommendation G.703 (DS3 and E3 standard) * ITU Recommendation G.823 and G.824 (jitter and wander) * Bellcore GR499, Issue 1, 12/89 (formerly TR-TSY-000499) (DS3 and STS-1 requirements) * Bellcore GR253, Issue 2, 12/91 (formerly TA-NWT-000253) (STS-1 Requirements and Jitter) * Bellcore TR-TSY-000191, Issue 1, 5/86 (AIS and LOS) * ETSI TBR24 and TBR25 (E3 terminal equipment interface) * ETSI ETS 300 686 and ETS 300 687 (E3 standard) * AT&T Technical Reference TR54014, May 1992 (Accunet Interface Specification for DS-3 jitter only) * ETSI ETS 300 687, 1996, "Business Telecommunications; 34 Mbps Digital Leased Lines (D34U and D34S); Connection Characteristics" * ETSI ETS 300 686, 1996, "Business Telecommunication; 34 Mbps and 140 Mbps digital Leased Lines (D34U, D34S, D140U, and D140S); Network Interface presentation" * ANSI T1.102-1993, "Digital Hierarchy--Electrical Interfaces" * ANSI T1.107-1995, "Digital Hierarchy--Formats Specification" * ANSI T1.231-1997, Draft, "Digital Hierarchy--Layer 1 In-Service Digital Transmission Performance Monitoring" * ANSI T1.231-1993, "Digital Hierarchy--Layer 1 In-Service Digital Transmission Performance Monitoring" * ANSI T1.404-1994, "Network-to-Customer Installation--DS3 Metallic Interface Specification" * Bellcore GR-499-CORE, Issue 1, December 1995, "Transport Systems Generic Requirements (TSGR): Common Requirements" * Bellcore GR-253-CORE, Issue 2, December 1995, "SONET Transport Systems: Common Generic Criteria" * ITU Recommendation G.703, 1991, "Physical/Electrical Characteristics of Hierarchical Digital Interfaces" * ITU Recommendation G.823, 1993, "The Control of Jitter and Wander Within Digital Networks Which are Based on the 2,048 kbps Hierarchy" * ITU Recommendation O.151, 1992, "Error Performance Measuring Equipment Operating at the Primary Rate and Above" * ETSI TBR 24, 1997, "Business Telecommunication; 34 Mbps Digital Unstructured and Structured Lease Lines; Attachment Requirements for Terminal Equipment Interface" 28333-DSH-003-A Mindspeed TechnologiesTM A-1 M28331/M28332/M28333 (-3x) Appendix A: Applicable Standards Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit A-2 Mindspeed TechnologiesTM 28333-DSH-003-A B Appendix B: Exposed Thin Quad Flat (ETQFP) Pack NOTE: Mindspeed recommends that the exposed paddle on the M28333-3x be soldered to the ground side of the PCB for reasons described below. Do not route PCB traces or vias under the exposed paddle area of the M28333-3x device. The Exposed Thin Quad Flat Pack (ETQFP) package provides greater design flexibility and increased thermal efficiency, while using a standard size IC package. The exposed pad improves performance by permitting higher clock speeds, more compact systems, and a more aggressive design criteria. ETQFP thermal performance is better than standard packages; however, to make optimum use of the thermal efficiencies designed into the ETQFP, the PCB must be designed with this package in mind. The following sections of this document provide more information regarding the thermal performance and PCB design for Mindspeed ETQFPs. 28333-DSH-003-A Mindspeed TechnologiesTM B-1 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.1 Introduction B.1 Introduction The ETQFP is implemented using a standard epoxy-resin package mold compound. The integrated circuit die is attached to the lead-frame die pad with a thermally conductive epoxy. The leadframe is designed with a deep downset of the die attach pad so it will be exposed on the bottom surface of the package after mold. This provides an extremely low thermal resistance between the IC junction and the exterior of the surface. The die pad's external surface can be attached to the PCB using standard solder reflow techniques. This allows efficient attachment to the board, and permits the board structure to be used as a heat sink for the IC. Using thermal vias, the lead frame die pad can be attached to a ground plane or special heat sink structure designed into the PCB. Figure B-1 illustrates the schematic of the package components. Figure B-1. Schematic Representation of the Package Components Mold Compound Die Lead Frame Lead Frame Die Attach 100998_030 B-2 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization B.2 Package Thermal Characterization B.2.1 Heat Removal Path The internal heat removal path is designed to transfer heat from the top surface of the die to the die pad and then directly to the Printed Circuit Board (PCB) through a center solder pad. The PCB must have features designed to remove heat from the package efficiently. At a minimum, there must be an area of solder-tinned copper underneath the ETQFP, called a thermal land. Heat is transferred from the thermal land to the environment through thermal vias designed within the PCB structure. B.2.2 Thermal Lands A thermal land is required on the surface of the PCB directly under the body of the exposed package. During normal surface mount reflow, the exposed pad on the underside of the package will be soldered to this thermal land creating an efficient thermal path. The size of the thermal path is as large as needed to dissipate the required heat. For double-sided PCBs having no internal layers, the surface layers must be used to remove heat. Figure B-2 illustrates a sample package detail, including the required solder mask and thermal land pattern for an EQTFP. The designer may consider external means of heat conduction, such as attaching the copper planes to a convenient chassis member or other hardware convection. Figure B-2. Package and PCB Land Configuration PCB Center Pad = Body Size - 2.0 mm Via Dia. + 0.1 mm Thermal Via x N, 0.33 mm Dia. Mask Opening, F sq. A C B D E Metalization Pattern Comp Side Solder Mask Comp Side 100998_024 28333-DSH-003-A Mindspeed TechnologiesTM B-3 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization An array of 0.33 mm diameter thermal vias plated with 1 oz. copper must be placed on the pad and shorted to the PCB's ground plane. If the plating thickness in the exposed region of the center pad is not sufficient to effectively plug the barrel of the via when plated, use solder mask to cap the vias; the mask diameter should have a dimension equal to the via diameter + 0.1 mm minimum. This prevents the solder from wicking through the thermal via, potentially creating a solder void in the region between the package bottom and the center pad on the surface of the PCB. Table B-1 lists the dimensions for the entire ETQFP package family. Table B-1. Dimensional Parameters (mm) Package Type A B C D E F N(1) 48-lead ETQFP 5.40 5.40 0.50 0.25 1.00 4.70 sq. 3 x 3; 9 80-lead ETQFP 14.40 14.40 0.65 0.35 1.00 6.50 sq. 7 x 7; 49 100-lead ETQFP 14.40 14.40 0.50 0.25 1.00 8.00 sq. 7 x 7; 49 NOTE(S): (1) B-4 N represents the total number of thermal vias to be placed evenly across the entire PCB center pad. In the case of the 48-lead ETQFP, all thermal vias are located within the exposed region of the center pad. Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization B.2.3 PCB Design Thermal vias are the primary method of heat transfer from the PCB thermal land to the internal copper planes or to other heat removal sinks. The number, size, and construction of the vias is important in obtaining the best package thermal performance and package/PCB assembly. Thermal performance analysis indicates there is a point of diminishing returns where additional vias will not improve heat transfer through the board. The PCB internal structure plays a very important role in package thermal performance. Figures B-3 and B-4 illustrate the PCB structure for a two- and six-layer design, respectively. PCB designs with more than two layers should have all thermal vias connected to the ground plane. Figure B-3. Internal Structure for a Two-Layer PCB 60 Micron Solder Mask Layer 1/2 Oz Copper Layer Thermal Via Core Laminate Layer 1.50 mm 1/2 Oz Copper Layer 60 Micron Solder Mask Layer 100998_029 Figure B-4. Internal Structure For a Six-Layer PCB 60 Micron Solder Mask Layer 1/2 Oz Copper Layer 1 Oz Copper Layer 1 Oz Copper Layer 1 Oz Copper Layer 1 Oz Copper Layer Core Laminate Layer 1.50 mm Thermal Via Electrical Isolation 1/2 Oz Copper Layer 60 Micron Solder Mask Layer 100998_028 28333-DSH-003-A Mindspeed TechnologiesTM B-5 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization B.2.4 Thermal Test Structure B.2.4.1 Test Environment Package thermal performance has been tested following JEDEC standards. The ETQFP package is mounted at the center of a 100 mm x 100 mm, six layer test board and is tested under different air flow velocities. Figure B-5 illustrates the system configuration. Figure B-5. Test Performance Structure (A = 100 mm, B = 100 mm, LP = 1.40 mm, LB = 1.60 mm) LP LB B A Air Flow 100998_027a B.2.4.2 Thermal Test Boards Two different test boards have been used to evaluate package thermal performance for both worst and best conditions. Table B-2 lists specifications of these test boards. Table B-2. Specification for a Two-Layer Test Board Drawing Number TR03-T1 Substrate Material FR-4 Thickness 1.6 mm Stackup (signal layers, Cu planes) 1S0P Cu Coverage (signal layer--top/bottom) 10% Cu Coverage (power/ground layer) 100% Inner Cu Thickness (spec) 35 x 3.5 Table B-3. Specification for a Four-Layer Test Board Drawing Number TR03-T2 Substrate Material Thickness FR-4 1.6 mm Stackup (signal layers, Cu planes) 1S2P Cu Coverage (signal layer--top/bottom) 10% Cu Coverage (power/ground layer) 100% Inner Cu Thickness (spec) B-6 35 x 3.5 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization B.2.5 Package Thermal Performance B.2.5.1 Calculation Guidelines Maximum junction temperature can be calculated as: B.2.5.2 Package Thermal Resistance Delco thermal test chips are used to estimate package thermal performance. Table B-4 lists thermal die specifications. Tj = P x ja + Ta Where: ja = Equivalent Package Thermal Resistance (C/W) Tj = Maximum Junction Temperature (C) Ta = Ambient Temperature (C) P = Package Total Power Dissipation Value (W) Table B-4. Specification for Delco Thermal Test Chips Dimensions 3.81 mm x 3.81 mm 6.35 mm x 6.35 mm 7.8 mm x 7.8 mm Thickness 0.33 mm 0.45 mm 0.5 mm Figure B-6 illustrates package thermal resistance as a function of airflow velocity for a 48-pin ETQFP package using two different test boards, specified in Tables B-2 and B-3, and a prediction for a six-layer PCB design. Figures B-7 and B-8 illustrates the similar information for a 64- and 80-pin ETQFP package. Table B-5 lists the test condition for each package type. Figure B-6. Package Thermal Resistance as a Function of Airflow Velocity for a 48-ETQFP Package Package Thermal Resistance 80 Two Layer PCB 70 Four Layer PCB Six Layer PCB 60 50 40 30 20 10 0 0 50 100 150 200 250 300 350 400 450 500 Air Flow Velocity (LFM) 100998_031 28333-DSH-003-A Mindspeed TechnologiesTM B-7 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.2 Package Thermal Characterization Table B-5 lists the test conditions for Figures B-6 through B-8. Table B-5. Test Conditions Package Type: 48 EQTFP 64 ETQFP 80 ETQFP Body Size 7 mm x 7 mm 10 mm x 10 mm 14 mm x 14 mm Die Size 3.81 mm x 3.81 mm 6.35 mm x 6.35 mm 7.8 mm x 7.8 mm Die Pad Size 5 mm x 5 mm 7.50 mm x 7.50 mm 9.50 mm x 9.50 mm Figure B-7. Package Thermal Resistance as a Function of Airflow Velocity for an 64 ETQFP 60 Package Thermal Resistance Two Layer PCB Four Layer PCB 50 Six Layer PCB 40 30 20 10 0 0 50 100 150 200 250 300 350 400 450 500 Air Flow Velocity (LFM) 100998_032 Figure B-8. Package Thermal Resistance as a Function of Airflow Velocity for an 80 ETQFP Package Thermal Resistance 60 Two Layer PCB 50 Four Layer PCB Six Layer PCB 40 30 20 10 0 0 50 100 150 200 250 300 350 400 450 500 Air Flow Velocity (LFM) 100998_033 B-8 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.3 Solder Stencil Determination B.3 Solder Stencil Determination Use the thickest possible solder mask, consistent with the components being assembled to the PWB surface mount process. A standoff height of 2.0-4.2 mils provides good solder joints for both the leads and the center pad. This is achieved using a stencil thickness of 5, 6, or 7 mils. B.4 Solder Reflow Profile The ETQFP uses the standard TQFP reflow profile because the ETQFP package construction does not add thermal mass. There is minimal additional thermal load due to the increased solder area between the exposed die pad on the package and the center pad on the PCB. Figures B-9 and B-10 illustrate typical IR reflow profiles for Sn63:Pb37 solder in the cases of natural convection and forced convection ovens. 28333-DSH-003-A Mindspeed TechnologiesTM B-9 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.4 Solder Reflow Profile Figure B-9. Typical IR Reflow Profile for Eutectic Sn63:Pb37 300 270 Temperature (C) 240 210 180 150 120 90 60 30 0 Minute Peak: 1 0.0 219 2 3 0.6 4 5 1.2 Max Slope: -3.2 6 7 1.9 2.5 8 9 10 3.1 Seconds Over 183: 48 3.7 4.4 Time Belt Speed = 38.00 inches/minute ZONE SETPOINTS 1 160 2 125 9 265 10 260 3 115 4 110 5 190 6 190 7 160 8 190 NOTE(S): Peak temperature should be approximately 220 C, and the exposure time should normally be less than 1.0 minutes at temperature above 183 C. 100998_025 B-10 Mindspeed TechnologiesTM 28333-DSH-003-A M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit B.4 Solder Reflow Profile Figure B-10. Typical Forced Convection Reflow Profile for Eutectic Sn63:Pb37 File = SMOLE42 TWO2 - D675-001 MAXIMA X Deg. 1= 221 236.7 2 = 225 236.1 3 = 227 232.3 4 = 226 233.3 2470 STATUS-3 TEMP = 68 BATT = 5.893 P1s = 350 Act = X4321 00:00:01.0 04/29/98 12:00:08 1700 MAX SLOPES X Deg./Point 920 1= 27 4.4 2 = 33 6.7 3 = 31 6.7 4 = 32 9.4 5=0 0.0 150 +X-----> Thermocouple Location 1 = BOTTOM GROUND 2 = TQFP4B 3 = BBA 4 = MCM F1-F4 = Sample 1-4; SAMP 1 X = ?3 SAMP 2 X = 67 SAMP 3 X = 182 SAMP 4 X = 244 Temp Slope Temp Slope Temp Slope Temp Slope 35.0 1.1 147.2 1.1 185.6 1.1 185.0 -2.2 36.7 1.1 157.8 0.9 186.7 1.7 181.1 -4.4 32.8 1.1 153.9 1.7 182.2 1.7 187.8 -2.8 33.9 1.1 160.0 1.1 183.3 1.1 182.2 -3.3 OPEN 0.0 OPEN 0.0 OPEN 0.0 OPEN 0.0 F5 - ReScale X: F6 - ReScale Y: F7 = PRINT: Msc = Menu: 100998_026 Peak temperature should be approximately 235 C, and the exposure time should normally be less than 1.2 minutes at temperature above 183 C. Belt Speed = 30 inches/minute (top and bottom setting), FAN SPEED = 2500 RPM, NITROGEN LEVEL = 1200 SCFH. ZONE 1 = 185 C ZONE 2 = 185 C ZONE 3 = 175 C ZONE 4 = 175 C ZONE 5 = 180 C ZONE 6 = 190 C ZONE 7 = 230 C ZONE 8 = 270 C 28333-DSH-003-A Mindspeed TechnologiesTM B-11 M28331/M28332/M28333 (-3x) Appendix B: Exposed Thin Quad Flat (ETQFP) Pack B.4 Solder Reflow Profile B-12 Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit Mindspeed TechnologiesTM 28333-DSH-003-A C Appendix C: Power Sequencing When VGG is operated at 5V, use the power-up and power-down sequencing between VGG and VDD (DVDDC, RVDD, TVDD, VDD) as described in the diagrams below (refer to note below). NOTE: VGG can exceed VDD by up to 5V (10%) for short durations of less than 10 ms. VGG must never be less than VDD by more than 0.5V. Figure C-1. Power -up sequence of VGG and VDD. VGGmax 3.6V Max. VDD 3.6V Max. VGGmin 0.5V Max. 3.6V Max. 0.5V Max. 3.6V Max. VSS 5.5V Max. Time Figure C-2. Power-down sequence of VGG and VDD. VGGmax 3.6V Max. VDD VGGmin 5.5V Max. 3.6V Max. 0.5V Max. 3.6V Max. 0.5V Max. 3.6V Max. VSS Time 28333-DSH-003-A Mindspeed TechnologiesTM C-1 M28331/M28332/M28333 (-3x) Appendix C: Power Sequencing Single/Dual/Triple E3/DS3/STS-1 Line Interface Unit C-2 Mindspeed TechnologiesTM 28333-DSH-003-A www.mindspeed.com General Information: U.S. and Canada: (800) 854-8099 International: (949) 483-6996 Headquarters - Newport Beach 4311 Jamboree Rd. P.O. Box C Newport Beach, CA. 92658-8902