MS-156-HRMJ-2 - HIROSE Electric U.S.A., Inc.

1

Subminiature Coaxial Switch 1.6 mm High, DC to 6 GHz

MS-156NB Series

NEWNEW

2006.9

■Features

1. Low insertion loss

0.1 dB typical at 6 GHz (not mated with the plug).

2. Space-saving design

2.7 mm x 2.7 mm occupied board space.

3. Low profile

1.6 mm protrusion above the board.

4. Lightweight

0.025 g. total weight (without vacuum cap).

5. Durability

100 mating/unmating cycles, with corresponding plug.

6.

Performs over a wide frequency range

Applicable frequencies range over a wide band,

from DC to 6 GHz.

7.

Board placement with automatic equipment

Packaged on tape-and-reel. Also available with a

vacuum pick-up cap over each switch.

8.

RoHS compliant

All components and materials comply with the

requirements of the EU Directive 2002/95/EC.

■Applications

Portable terminals, ETC, notebook computers (Bluetooth),

wireless LAN, POS terminals, GPS terminals, PDA, and any

small devices requiring verification of antenna/circuit

performance.

■Overview

Developed for inspection of high frequency

circuits used in portable terminals.Verification of

the circuit performance is

accomplished by simply

inserting the external plug

in the board mounted

receptacle.This action re-directs the circuit from

normal condition to the plug side. Removing the

plug restores circuit to its normal condition.

MS-156NB

Space-saving design

Low profile -1.6 mm protrusion above the board.

Lightweight -0.025 g. total weight.

Several types of plugs

Several types of SMA conversion adapters

Adapter for plug inspection

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

2

■Product Specifications

100 mA max.

100 V DC

100 V AC / 1 minute

Frequency:10 to 55 Hz, single amplitude of

0.75 mm, 2 hours in each of the 3 axis.

Acceleration of 490 m/s2, 6 ms duration, sine half-

wave waveform, 3 cycles in each of the 3 axis

Temperature: -55ç /+5ç to +35ç /+85ç /+5ç to +35ç

Time: 30 /2 to 3 /30 /2 to 3 (Minutes)

100 cycles

100 mø max.

1000 Mø min.

No flashover or insulation breakdown

Contact resistance: 100 mø max.

Insulation resistance: 10 Mø min.

Contact resistance: 100 mø max.

1. Contact resistance

2. Insulation resistance

3. Withstanding voltage

4. Vibration

5. Shock

6. Thermal shock

7. Durability (mating/un-mating,

with corresponding plug)

Item Specification Conditions

Shell

Insulator

Common terminal

Antenna terminal

Phosphor bronze

9T Nylon

Beryllium copper

Phosphor bronze

Gold plated

---------------------------

Selective gold plated (Nickel barrier)

---------------------------

UL94V-0

---------------------------

Part Material Finish Remarks

Operating temperature range

Rated power

Frequency range

Insertion loss

Isolation

V.S.W.R

Not mated with the plug

-40ç to +85ç

2W

DC to 6GHz

0.1 dB max. (DC to 3.0GHz)

0.15 dB max. (3.0GHz to 6.0GHz)

1.2 max. (DC to 2.5GHz)

1.3 max. (2.5GHz to 6.0GHz)

Mated (MS-156-HRMJ-3)

-40ç to +85ç

2W

DC to 6GHz

0.5 dB max. (DC to 3.0GHz)

1.2 dB max. (3.0GHz to 6.0GHz)

1.4 max. (DC to 3.0GHz)

1.8 max. (3.0GHz to 6.0GHz)

20 dB max. (DC to 2.0GHz)

15 dB max. (2.0GHz to 4.0GHz)

13 dB max. (4.0GHz to 6.0GHz)

■Materials

No electrical discontinuity of 1 µs or more

MS-156NB Plug MS-156NB

G

B

G

C

G

A

Plug

G

B

G

C

G

A

Not mated with the plug(N.C) Mated with the plug(N.O)

BCircuit diagram

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3

BTypical Data

V.S.W.R.

1.0

1.1

1.2

1.3

DC 6.04.02.0 [GHz]

[dB]

0.0

0.1

0.2

0.3

INSERTION LOSS

4.02.0

INSERTION LOSS

V.S.W.R.

1.0

1.2

1.4

1.6

1.8

DC 6.0 [GHz]

[dB]

0.0

0.5

1.0

1.5

4.02.0

10

15

20

25

30

35

40

45

ISOLATION

DC 6.0 [GHz]

[dB]

Insertion Loss [dB]

V.S.W.R.V.S.W.R.

Insertion Loss [dB]

Isolation [dB]

●NORMALLY CLOSED(N.C)~(Not mated with the plug)

●OPEN(N.O)~(Mated with the plug)

●ISOLATION

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

4

■Receptacle

BPCB mounting pattern and metal mask dimensions

0.4

1.6

Ø2

0.6 (0.05)

2.7

Center of

mating plug

1.4

2.7 A terminal

C terminal

P

Part Number

MS-156NB

MS-156NB(01)

CL No.

358-0206-8

358-0206-8-01

2,000 pieces/reel

100 pieces/bag YES

Packaging RoHS

1.15

Ø2.75

2

0.1 to 0.12 thick

This area must be free of conductive traces and resist field.

(3.4)

1.4

0.55

1.051.25

2-2.65

0.550.55

3

A terminal

C terminal

(2.9)

1.4

0.55

1.051.25

2-2.65

0.30.3

3

2-1.4

Center of mating plug Center of mating plug

Metal mask dimensions

PCB mounting pattern

Part Number

MS-156NB(02)

CL No.

358-0206-8-02 1,500 pieces/reel YES

Packaging RoHS

●With vacuum pick-up cap

●Without vacuum pick-up cap

Note:Vacuum pick-up cap flat can be oriented in any

direction. Orientation will not affect placement of

the switch on the board.

* Lead coplanarity within 0.1mm

* Request drawing of the specific part for exact dimensions and tolerances.

* Specified dimensions must be followed to assure correct board placement and performance.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6196444

5

BPrecautions

Recommended Mounting of MS-156NB coaxial switch

on the PCB during the manufacturing process

MS-156NB

To avoid contamination when cutting-off,

do not place PCB bridge close to the

mounted MS-156NB.

1. This product is intended to be used for circuit inspection only. Consult us if any other application is

considered.

2. Cross-hatched area shown on the PCB mounting pattern must be free of any conducive traces. Placing

conductive traces in this area may affect performance and will void product warranties.

When the bottom surface of the product (i.e., the shaded area of the specified land dimensions

diagram on the previous page) has been processed with a susbtrate copper trace and resist processing,

Hirose Electric will not be able to warrant the product.

3. Do not use hand soldering for mounting of MS-156NB.

Doing so could result in solder and flux wicking to the contact areas.

4. Exercise caution as not to allow any debris to enter the board mounted MS-156NB when cutting PCB.

5. Do not use the washing process.

6. Please refrain from using the product in environments specifically affected by excessive vibration, shock,

dust, high humidity, gases, very high temperatures and very low temperatures such as outdoor

equipment. It might cause degradation or destruction of the product.Even if it endures during a short time,

long time quarification is not quaranteed.

7. For use of this product, be sure to put contact area of plug on position P(P4 full view) perpendicularly.

8. Plugs can be roughly classified to two types.

- For mass production line automatic check (Press down type)

- For manual check (With retentive lock) : Unable to be used at production line.

9. When automatic inspections are to be performed during the manufacturing operations, request the MS-

156 plug connector manual for examples of implementation.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6

BPackaging Specifications

●MS-156NB (Without vacuum cap) ●Reel dimensions

●MS-156NB(02) (With vacuum cap) ●Reel dimensions

BRecommended Nozzle Dimensions

2.2

4

2

Ø1.5

5.5 1.75

12

12.4

Ø13

Ø180

Ø80

Unreeling direction

2,000 pieces/reel

2.6

4

2

Ø1.5

5.5 1.75

12

12.4

Ø13

Ø180

Ø80

1,500 pieces/reel

Unreeling direction

Ø0.5~1.0 Ø0.5~1.0 Ø4

Ø1max.

Ø2.5 min.

Ø2.6 min

* Depending on the placement equipment, the use of a special nozzle might be required.

●Without vacuum pick-up cap ●With vacuum pick-up cap

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

7

BRecommended Temperature Profile

10 sec.max.

Temperature (ç)

50

0

100

150

160

200

240

40 sec.min. 50 sec.max. Time (sec.)

qMaximum temperature

wPeak temperature

ePeak temperature time

r200ç min.

t150ç to 160ç

Metal mask thickness

Reflow cycles : 0.1 to 0.12 mm

: 2 cycles

: 240ç

: 220ç to 235ç

: 10 sec. max.

: 50 sec. max.

: 40 sec. min.

Using Typical Solder Paste

qMaximum temperature

wPeak temperature

ePeak temperature time

r230ç min.

t150ç to 180ç

Metal mask thickness

Reflow cycles : 0.1 to 0.12 mm

: 2 cycles

: 250ç

: 240ç to 250ç

: 10 sec. max.

: 30 sec. max.

: 60 sec. to 90 sec.

Using Lead-free Solder paste

30 sec.max.

Temperature (ç)

50

0

100

150

200

180

230

250

60 sec. to 90 sec. Time (sec.)

10 sec.max.

* Max. temperature 260ç for 10 sec. max. for heat gun or heat plate.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

8

■Plugs

●Press down, right angle

Ø3.2

20.9

Ø4

Ø6

4-C1

11.15 2.9

M8

Part Number

Applicable cable: 1.5D-HQEW, 1.5D-QEW (Fujikura Ltd.)

CL No. Durability RoHS

358-0173-0MS-156-C(LP)-1 10,000 Times YES

●Simplified lock, right angle

Ø7.9

Ø5.48

Ø4

Ø0.5

4-C1

8.2510

3

25.25

Ø3.2

1.6

M8

Part Number

Applicable cable: 1.5D-HQEW, 1.5D-QEW (Fujikura Ltd.)

CL No. Durability RoHS

358-0174-3MS-156-C(LP)-2 500 Times YES

■SMA Conversion Adapters

●Simplified lock, straight, short

Ø0.5

24.4

1.6 8

1/4-36UNS-2A

Ø4.27

Ø5.48

Ø8.5

5.2

11.3

Part Number CL No. Durability RoHS

358-0170-2MS-156-HRMJ-2 500 Times YES

●Simplified lock, straight, long

Ø0.5

8

Ø

8.5

1/4-36UNS-2A

5.219.8

12

32.9

Ø4.3

Ø5.48

1.6

Part Number CL No. Durability RoHS

358-0177-1MS-156-HRMJ-5 500 Times YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6196488

6196472

6196466

6196450

9

●Press down, with flange, short

1/4-36UNS-2A

18.63

8.12

8

28.13

Ø20

14

Ø3.4

Ø5

1

2-Ø2.6

Part Number CL No. Durability RoHS

358-0171-5MS-156-HRMJ-3 10,000 Times YES

8

33.01

13

23.51

Ø3.4

Ø5

2-Ø2.6

14

1/4-36UNS-2A

1

Ø20

Part Number CL No. Durability RoHS

358-0198-1MS-156-HRMJ-14 10,000 Times YES

●Press down, with flange

(Increased self alignment)

Ø4.3

Ø5.9

14

8

2-Ø2.6

Ø20

1

28.13

18.63

8.12

1/4-36UNS-2A

Part Number CL No. Durability RoHS

358-0181-9MS-156-HRMJ-6 10,000 Times YES

●Press down, with flange, long

●Floating

4.27

1.45

2-Ø2.6

Ø24

15

20

Ø3.4

Ø5

Ø10

2.5

20.7

31.06

1/4-36UNS-2A

Part Number CL No. Durability RoHS

358-0180-6MS-156-HRMJ-9 10,000 Times YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

10

●Adapter for plug inspection

0.75 13.21 2.54

41.9

14.3

5/8-24NEF-2A

Ø2

Ø5.45

Ø22

Part Number CL No. Durability RoHS

358-0176-9MS-156R-NJ-1 500 Times YES

●Floating (Self-Pressing)

13

Ø3.8

11.75

28.24 2.5

38.6

20

1/4-36UNS-2A

1.45

Ø5.4

Ø10.3

Ø24

2-Ø2.6

Part Number CL No. Durability RoHS

358-0194-0MS-156-HRMJ-10 10,000 Times YES

12

Ø4.3

Ø5.9

Ø10.3

11.75

29.49 2.5

39.85

3.75

20

1/4-36UNS-2A

Ø24

2-Ø2.6

Part Number CL No. Durability RoHS

358-0196-6MS-156-HRMJ-12 10,000 Times YES

●Adapter for plug inspection

Ø2

Ø6

8.3

Ø9

3 6.3

16.05

0.75

1/4-36UNS-2A

Part Number CL No. Durability RoHS

358-0188-8MS-156R-HRMJ-1 500 Times YES

●Floating (Self-Pressing)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.