PEX 8649, PCI Express Gen 2 Switch, 48 Lanes, 12 Ports Highlights PEX 8649 General Features o 48-lane, 12-port PCIe Gen2 switch - Integrated 5.0 GT/s SerDes o 27 x 27mm2, 676-ball FCBGA package o Typical Power: 6.7 Watts The ExpressLaneTM PEX 8649 device offers Multi-Host PCI Express switching capability enabling users to connect multiple hosts to their respective endpoints via scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage systems, and communications platforms. The PEX 8649 is well suited for fan-out, aggregation, and peer-to-peer applications. PEX 8649 Key Features o Standards Compliant - PCI Express Base Specification, r2.0 (backwards compatible w/ PCIe r1.0a/1.1) - PCI Power Management Spec, r1.2 - Microsoft Vista Compliant - Supports Access Control Services - Dynamic link-width control - Dynamic SerDes speed control o High Performance performancePAK 9 Read Pacing (bandwidth throttling) 9 Multicast 9 Dynamic Buffer/FC Credit Pool - Non-blocking switch fabric - Full line rate on all ports - Packet Cut-Thru with 176ns max packet latency (x16 to x16) - 2KB Max Payload Size o Flexible Configuration - Ports configurable as x1, x2, x4, x8, x16 - Registers configurable with strapping pins, EEPROM, I2C, or host software - Lane and polarity reversal - Compatible with PCIe 1.0a PM o Multi-Host & Fail-Over Support - Configurable Non-Transparent (NT) port - Failover with NT port - Up to Four upstream/Host ports with 1+1 or N+1 failover to other upstream ports o Quality of Service (QoS) - Eight traffic classes per port - Weighted round-robin source port arbitration o Reliability, Availability, Serviceability visionPAK 9 Per Port Performance Monitoring Per port payload & header counters 9 SerDes Eye Capture 9 Error Injection and Loopback - 3 Hot Plug Ports with native HP Signals - All ports hot plug capable thru I2C (Hot Plug Controller on every port) - ECRC and Poison bit support - Data Path parity - Memory (RAM) Error Correction - INTA# and FATAL_ERR# signals - Advanced Error Reporting - Port Status bits and GPIO available * Per port error diagnostics - JTAG AC/DC boundary scan (c) PLX Technology, www.plxtech.com Multi-Host Architecture The PEX 8649 employs an enhanced version of PLX's field tested PEX 8648 PCIe switch architecture, which allows users to configure the device in legacy single-host mode or multi-host mode with up to four host ports capable of 1+1 (one active & one backup) or N+1 (N active & one backup) host failover. This powerful architectural enhancement enables users to build PCIe based systems to support high-availability, failover, redundant and clustered systems. High Performance & Low Packet Latency The PEX 8649 architecture supports packet cut-thru with a maximum latency of 176ns (x16 to x16). This, combined with large packet memory, flexible common buffer/FC credit pool and non-blocking internal switch architecture, provides full line rate on all ports for performance-hungry applications such as servers and switch fabrics. The low latency enables applications to achieve high throughput and performance. In addition to low latency, the device supports a packet payload size of up to 2048 bytes, enabling the user to achieve even higher throughput. Data Integrity The PEX 8649 provides end-to-end CRC (ECRC) protection and Poison bit support to enable designs that require end-to-end data integrity. PLX also supports data path parity and memory (RAM) error correction circuitry throughout the internal data paths as packets pass through the switch. Flexible Configuration The PEX 8649's 12 ports can be configured to lane widths of x1, x2, x4, x8, or x16. Flexible buffer allocation, along with the device's flexible packet flow control, maximizes throughput for applications where more traffic flows in the downstream, rather than upstream, direction. Any port can be designated as the upstream port, which can be changed dynamically. Figure 1 shows some of the PEX 8649's common port configurations in legacy Single-Host mode. Page 1 of 1 5/14/2009, Version 1.1 PEX 8649, PCI Express Gen 2 Switch, 48 Lanes, 12 Ports The PEX 8649 can also be configured in Multi-Host mode where users can choose up to four ports as host/upstream ports and assign a desired number of downstream ports to each host. In Multi-Host mode, a virtual switch is created for each host port and its associated downstream ports inside the device. The traffic between the ports of a virtual switch is completely isolated from the traffic in other virtual switches. Figure 2 illustrates some configurations of the PEX 8649 in Multi-Host mode where each ellipse represents a virtual switch inside the device. The PEX 8649 x8 x8 x8 x4 x4 also provides several ways to configure its PEX 8649 PEX 8649 registers. The device can be configured 3 x8 2 x4 2 x8 2 x4 2 x4 through strapping 4 x4s 3 x4s pins, I2C interface, host software, or an optional serial PEX 8649 PEX 8649 EEPROM. This allows for easy 8 x4s 9 x4s debug during the Figure 2. Common Multi-Host Configurations development phase, performance monitoring during the operation phase, and driver or software upgrade. Dual-Host & Failover Support In Single-Host mode, the PEX 8649 supports a NonTransparent (NT) Port, which enables the implementation of dualhost systems for redundancy and host failover capability. The NT port allows systems to isolate host memory domains by presenting the processor subsystem as an endpoint rather than another memory system. Base address registers are used to translate addresses; doorbell registers are used to send interrupts between the address domains; and scratchpad registers (accessible by both CPUs) allow inter-processor communication (see Figure 3). (c) PLX Technology, www.plxtech.com Multi-Host & Failover Support In Multi-Host mode, PEX 8649 can be configured with up to four upstream host ports, each with its own dedicated downstream ports. The device can be configured for 1+1 redundancy or N+1 redundancy. The PEX 8649 allows the hosts to communicate their status to each other via special door-bell registers. In failover mode, if a host fails, the host designated for failover will disable the upstream port attached to the failing host and program the downstream ports of that host to its own domain. Figure 4a shows a two host system in Multi-Host mode with two virtual switches inside the device and Figure 4b shows Host 1 disabled after failure and Host 2 having taken over all of Host 1's end-points. Host 1 Host 2 Host 1 PEX 8649 End Point End Point End Point Host 2 PEX 8649 End Point Figure 4a. Multi-Host End Point End Point End Point End Point Figure 4b. Multi-Host Fail-Over Hot Plug for High Availability Hot plug capability allows users to replace hardware modules and perform maintenance without powering down the system. The PEX 8649 hot plug capability feature makes it suitable for High Availability (HA) applications. Three downstream ports include a Standard Hot Plug Controller. If the PEX 8649 is used in an application where one or more of its downstream ports connect to PCI Express slots, each port's Hot Plug Controller can be used to manage the hot-plug event of its associated slot. Every port on the PEX 8649 is equipped with a hot-plug control/status register to support hot-plug capability through external logic via the I2C interface. SerDes Power and Signal Management The PEX 8649 supports software control of the SerDes outputs to allow optimization of power and signal strength in a system. The PLX SerDes implementation supports four levels of power - off, low, typical, and high. The SerDes block also supports loop-back modes and advanced reporting of error conditions, which enables efficient management of the entire system. Page 2 of 2 5/14/2009, Version 1.1 PEX 8649, PCI Express Gen 2 Switch, 48 Lanes, 12 Ports Interoperability visionPAKTM The PEX 8649 is designed to be fully compliant with the PCI Express Base Specification r2.0, and is backwards compatible to PCI Express Base Specification r1.1 and r1.0a. Additionally, it supports auto-negotiation, lane reversal, and polarity reversal. Furthermore, the PEX 8649 is tested for Microsoft Vista compliance. All PLX switches undergo thorough interoperability testing in PLX's Interoperability Lab and compliance testing at the PCI-SIG plug-fest. Another PLX exclusive, visionPAK is a debug diagnostics suite of integrated hardware and software instruments that users can use to help bring their systems to market faster. visionPAK features consist of Performance Monitoring, SerDes Eye Capture, Error Injection, SerDes Loopback, and more. Performance Monitoring performancePAKTM Exclusive to PLX, performancePAK is a suite of unique and innovative performance features which allows PLX's Gen 2 switches to be the highest performing Gen 2 switches in the market today. The performancePAK features consists of the Read Pacing, Multicast, and Dynamic Buffer Pool. Read Pacing The Read Pacing feature allows users to throttle the amount of read requests being made by downstream devices. When a downstream device requests several long reads back-to-back, the Root Complex gets tied up in serving that downstream port. If that port has a narrow link and is therefore slow in receiving these read packets from the Root Complex, then other downstream ports may become starved - thus, impacting performance. The Read Pacing feature enhances performances by allowing for the adequate servicing of all downstream devices. The PEX 8649's real time performance monitoring allows users to literally "see" ingress and egress performance on each port as traffic passes through the switch using PLX's Software Development Kit (SDK). The monitoring is completely passive and therefore has no affect on overall system performance. Internal counters provide extensive granularity down to traffic & packet type and even allows for the filtering of traffic (i.e. count only Memory Writes). SerDes Eye Capture Users can evaluate their system's signal integrity at the physical layer using the PEX 8649's SerDes Eye Capture feature. Using PLX's SDK, users can view the receiver eye of any lane on the switch. Users can then modify SerDes settings and see the impact on the receiver eye. Figure 5 shows a screenshot of the SerDes Eye Capture feature in the SDK. Multicast The Multicast feature enables the copying of data (packets) from one ingress port to multiple (up to 11) egress ports in one transaction allowing for higher performance in dualgraphics, storage, security, and redundant applications, among others. Multicast relieves the CPU from having to conduct multiple redundant transactions, resulting in higher system performance. Dynamic Buffer Pool The PEX 8649 employs a dynamic buffer pool for Flow Control (FC) management. As opposed to a static buffer scheme which assigns fixed, static buffers to each port, PLX's dynamic buffer allocation scheme utilizes a common pool of FC Credits which are shared by other ports. This shared buffer pool is fully programmable by the user, so FC credits can be allocated among the ports as needed. Not only does this prevent wasted buffers and inappropriate buffer assignments, any unallocated buffers remain in the common buffer pool and can then be used for faster FC credit updates. (c) PLX Technology, www.plxtech.com Figure 5. SerDes Eye Capture Error Injection & SerDes Loopback Using the PEX 8649's Error Injection feature, users can inject malformed packets and/or fatal errors into their system and evaluate a system's ability to detect and recover from such errors. The PEX 8649 also supports Internal Tx, External Tx, Recovered Clock, and Recovered Data Loopback modes. Page 3 of 3 5/14/2009, Version 1.1 PEX 8649, PCI Express Gen 2 Switch, 48 Lanes, 12 Ports Applications Suitable for host-centric as well as peer-to-peer traffic patterns, the PEX 8649 can be configured for a wide variety of form factors and applications. CPU CPU CPU CPU Chip Set Chip Set Chip Set Chip Set Host Centric Fan-out The PEX 8649, with its symmetric or asymmetric lane configuration capability, allows user-specific tuning to a variety of host-centric applications. Figure 6 shows a server design where, in a quad or multi processor system, users can assign endpoints/slots to CPU cores to distribute the system load. The packets directed to different CPU cores will go to different (user assigned) PEX 8649 upstream ports, allowing better queuing and load balancing capability for higher performance. Conversely, the PEX 8649 can also be used in single-host mode to simply fanout to endpoints. PEX 8649 I/O I/O I/O I/O I/O I/O I/O I/O Figure 7. Multi-Host System Host Failover The PEX 8649 can also be utilized in applications where host failover is required. In the below application (Figure 8), two hosts may be active simultaneously and controlling their own domains while exchange status information through doorbell registers or I2C interface. The devices can be programmed to trigger fail-over if the heartbeat information is not provided. In the event of a failure, the surviving device will reset the endpoints connected to the failing CPU and enumerate them in its own domain without impacting the operation of endpoints already in its domain. CPU CPU CPU CPU CPU CPU CPU CPU Chipset Chipset x8 x8 Figure 6. Host Centric Dual Upstream x8s (c) PLX Technology, www.plxtech.com Endpoint x4 & x8 Endpoint PEX 8649 Endpoint Endpoint In multi-host mode, the PEX 8649 can be shared by up to four hosts in a system. By creating four virtual switches, the PEX 8649 allows four hosts to fan-out to their respective endpoints. This reduces the number of switches required for fan-out, saving precious board space and power consumption. In Figure 7, the PEX 8649 is being shared by four different servers (hosts) with each server is running its own applications (I/Os). The PEX 8649 assigns the endpoints to the appropriate host and isolates them from the other hosts. Endpoint Multi-Host Systems Endpoint PEX 8649 Figure 8. Host Fail-Over N+1 Fail-Over in Storage Systems The PEX 8649's Multi-Host feature can also be used to develop storage array clusters where each host manages a set of storage devices independent of others (Figure 9). Users can designate one of the hosts as the failover-host for all the other hosts while actively managing its own endpoints. The failover-host will communicate with other hosts for status/heartbeat information and execute a failover event if/when it gets triggered. Page 4 of 4 5/14/2009, Version 1.1 PEX 8649, PCI Express Gen 2 Switch, 48 Lanes, 12 Ports CPU CPU CPU CPU CPU CPU CPU CPU x4 x4 x4 x4 x8 Development Tools PLX offers hardware and software tools to enable rapid customer design activity. These tools consist of a hardware module (PEX 8649 RDK), hardware documentation (available at www.plxtech.com), and a Software Development Kit (also available at www.plxtech.com). x8 PEX 8649 x8 x8 PEX PEX 8616 PEX 8616 PEX 8612 x4 x4 x4 x4 PEX 8612 x4 x4 FC FC x4 x4 FC FC FC FC FC ExpressLane PEX 8649 RDK The PEX 8649 RDK (see Figure 10) is a hardware module containing the PEX 8649 which plugs right into your system. The PEX 8649 RDK can be used to test and validate customer software, or used as an evaluation vehicle for PEX 8649 features and benefits. The PEX 8649 RDK provides everything that a user needs to get their hardware and software development started. FC 8 Disk Chassis 8 Disk Chassis 8 Disk Chassis 8 Disk Chassis Figure 9. N+1 Failover. Software Usage Model From a system model viewpoint, each PCI Express port is a virtual PCI to PCI bridge device and has its own set of PCI Express configuration registers. It is through the upstream port that the BIOS or host can configure the other ports using standard PCI enumeration. The virtual PCI to PCI bridges within the PEX 8649 are compliant to the PCI and PCI Express system models. The Configuration Space Registers (CSRs) in a virtual primary/secondary PCI to PCI bridge are accessible by type 0 configuration cycles through the virtual primary bus interface (matching bus number, device number, and function number). Software Development Kit (SDK) PLX's Software Development Kit is available for download at www.plxtech.com/sdk. The software development kit includes drivers, source code, and GUI interfaces to aid in configuring and debugging the PEX 8649. For more information, please refer to the PEX 8649 RDK Product Brief. Both performancePAK and visionPAK are supported by PLX's RDK and SDK, the industry's most advanced hardware- and software-development kits. Product Ordering Information Part Number Interrupt Sources/Events The PEX 8649 switch supports the INTx interrupt message type (compatible with PCI 2.3 Interrupt signals) or Message Signaled Interrupts (MSI) when enabled. Interrupts/messages are generated by PEX 8649 for hot plug events, doorbell interrupts, baseline error reporting, and advanced error reporting. PEX8649-AA50BC F PEX8649-16U16D AIC RDK Description 48-Lane, 12-Port PCI Express Switch, Pb-Free (27x27mm2) PEX 8649 Rapid Development Kit with x16 Upstream and Two x16 Downstream PLX Technology, Inc. All rights reserved. PLX, the PLX logo, ExpressLane, Read Pacing and Dual Cast are trademarks of PLX Technology, Inc. All other product names that appear in this material are for identification purposes only and are acknowledged to be trademarks or registered trademarks of their respective companies. Information supplied by PLX is believed to be accurate and reliable, but PLX assumes no responsibility for any errors that may appear in this material. PLX reserves the right, without notice, to make changes in product design or specification. Visit www.plxtech.com for more information. Figure 10. PEX8649-16U16D AIC RDK (c) PLX Technology, www.plxtech.com Page 5 of 5 5/14/2009, Version 1.1 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Avago Technologies: PEX 8649-AA50BC F PEX 8649-16U16D AIC RDK PEX 8649-AA50RBC F PEX8649-16U16DAICRDK PEX8649AA50BC F PEX8649-AA50RBC F