ISL29006IROZ-T7 - Intersil - Datasheet.Directory

FN6282.1

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

ISL29006, ISL29007, ISL29008

Small, Low Power, Current-Output

Ambient Light Photo Detect IC

The ISL29006, ISL29007, and ISL29008 are light-to-current

silicon optical sensors combining a photodiode array and a

current amplifier on a single monolithic IC. The photodiode’s

spectral sensitivity approximates the human eye response

peaking at 550nm with virtually no infrared (IR) response.

Exposed to light, these light sensors give current outputs

that are linearly proportional to the light intensity. The output

of ISL29006 is configured as a current source, and the

output of ISL29007 is configured as a current sink. Both

ISL29006 and ISL29007 offer an EN pin that can be used for

a polling scheme to extend the battery life of portable

devices.

The ISL29008 has dual outputs simultaneously sinking and

sourcing current. With output currents at opposite polarity, it

can simultaneously control two light sources/drivers that

have incongruent illumination requireme nt depending on

ambient light conditions. For example, at bright ambient light

levels, display backpanels need more intensity while the

keyboard illumination needs to be dimmer, whereas at

darker ambient light levels, display backpanels need less

intensity while the keyboard illumination needs to be

brighter.

By connecting an external resistor from ISRC to GND or

from ISNK to VDD, the current output can be converted into

voltage output.

Housed in an ultra-compact 2mmx2.1mm ODFN clear

plastic package, this device is excellent for power saving

control function in cell phones, PDAs and other handheld

applications.

Features

• 0.5 lux to 10,000 lux range

• 1.8V to 3.6V supply range

• Low supply current (3.5µA @ 100 lux)

• Fast response time

• Close to human eye response

• IR Rejection

• Internal dark current compensation

• Lux to current source or/and sink

• Excellent output linearity of luminance

• 6 Ld ODFN: 2mmx2.1mmx0.7mm

• Pb-free (RoHS compliant)

Applications

• Display and keypad dimming for:

- Mobile devices: smart phone, PDA, GPS

- Computing devices: notebook PC, webpod

- Consumer devices: LCD-TV , digital picture frame, digit al

camera

• Industrial and medical light sensing

Ordering Information

PART NUMBER

(Note)

TEMP.

RANGE

(°C) PACKAGE

(Pb-free) PKG.

DWG. #

ISL29006IROZ-T7* -40 to +85 6 Ld ODFN L6.2x2.1

ISL29007IROZ-T7* -40 to +85 6 Ld ODFN L6.2x2.1

ISL29008IROZ-T7* -40 to +85 6 Ld ODFN L6.2x2.1

ISL29006IROZ-EVALZ Evaluation Board

ISL29007IROZ-EVALZ Evaluation Board

ISL29008IROZ-EVALZ Evaluation Board

*Please refer to TB347 for details on reel specifications.

NOTE: These Intersil Pb-free plastic packaged products employ

special Pb-free material sets; molding compounds/die attach

materials and 100% matte tin plate - e3 termination finish, which is

RoHS compliant and compatible with both SnPb and Pb-free

soldering operations. Intersil Pb-free prod ucts are MSL classified at

Pb-free peak reflow temperatures that meet or exceed the Pb-free

requirements of IPC/JEDEC J STD-020.

Data Sheet September 21, 2010

2FN6282.1

September 21, 2010

Pinouts ISL29006

(6 LD ODFN)

TOP VIEW

ISL29007

(6 LD ODFN)

TOP VIEW

ISL29008

(6 LD ODFN)

TOP VIEW

VDD

GND

ISRC

THERMAL

PAD*

VDD

GND

ISNK

THERMAL

PAD*

VDD

GND

ISRC

ISNK

THERMAL

PAD*

Pin Descriptions

ISL29006

PIN NUMBER ISL29007

PIN NUMBER ISL29008

PIN NUMBER NAME DESCRIPTION

1 1 1 VDD Supply, 1.8V to 3.6V

2 2 2 GND Ground

3, 5 3, 5 3, 5 NC No connect

46 EN

Active LOW enable

6 6 ISRC Current source out

4 4 ISNK Current sink out

Simplified Block Diagrams

ISL29006 ISL29007

ISL29008

VDD

ISRC

LIGHT DATA

PROCESS OUTPUT CURRE NT α LIGHT INTENSITY

PHOTODIODE

ARRAY 4

GND EN

CURRENT

AMPLIFIER

VDD

ISNK

LIGHT DATA

PROCESS OUTPUT CURRE NT α LIGHT INTENSITY

PHOTODIODE

ARRAY

GND

CURRENT

AMPLIFIER

VDD

ISRC

LIGHT DATA

PROCESS OUTPUT CURRENT α LIGHT INTENSITY

PHOTODIODE

ARRAY

GND

CURRENT

AMPLIFIER 4ISNK

ISL29006, ISL29007, ISL29008

3FN6282.1

September 21, 2010

Absolute Maximum Ratings (TA = +25°C) Thermal Information

Supply Voltage between VDD and GND . . . . . . . . . . . . . . . . . . 3.6V

Pin Voltage (ISRC, ISNK and EN) . . . . . . . . . . . . . . . -0.2V to 3.6V

Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . 6mA

Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-4 0°C to +85°C

ESD Voltage

Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV

Machine Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V

Thermal Resistance θJA (°C/W)

6 Ld ODFN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .+90°C

Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-45°C to +100°C

Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-45°C to +85°C

Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests

are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA

Electrical Specifications VDD = 3V, TA = +25°C, RL = 100kΩ, green LED light, unless otherwise specified.

PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT

E Range of Input Light Intensity 0.5 to 10k lux

VDD Power Supply Range 1.8 3.3 V

IDD Supply Current E = 1000 lux 27 35 µA

E = 100 lux 3.5 µA

E = 0 lux 250 nA

ISRC1 Light-to-Current Sourcing Accuracy IS29006 and ISL29008

E = 100 lux 1.65 µA

ISNK1 Light-to-Current Sinking Accuracy ISL29007 and ISL29008

E = 100 lux 1.65 µA

ISRC2 Light-to-Current Sourcing Accuracy ISL29006 and ISL29008

E = 1000 lux 11.5 16.45 21.3 µA

ISNK2 Light-to-Current Sinking Accuracy ISL29007 and ISL29008

E = 1000 lux 11.5 16.45 21.3 µA

ISNK/ISRC Mismatch between ISNK and ISRC E = 1000 lux for ISL29008 0.9 1.00 1.1 µA

IDARK Dark Current Output in the Absence of Light E = 0 lux, RL = 10MΩ0.22 2.5 µA

ΔIOUT Output Current Variation Over Three Light Sources:

Fluorescent, Incandescent and Halogen E = 1000 lux 20 %

ISD Supply Current when Shut Down 350 nA

VO-MAX1 ISRC Max Output Compliance Voltage at 95% of

Nominal Output IS29006 andISL29008

E = 1000 lux VDD - 0.2 V

VO-MAX2 ISNK Min Output Compliance Voltage at 95% of

Norminal Output ISL29007 and ISL29008

E = 1000 lux 0.2 V

tRISRC and ISNK Rise Time (Note 1) RL = 100kΩ, E = 300 lux

from 0 Lux 104 µs

RL = 100kΩ, E = 1000 lux

from 0 Lux 27 µs

tFISRC and ISNK Fall Time (Note 1) RL = 100kΩ, E = 300 lux to

0 Lux 562 µs

RL = 100kΩ, E = 1000 lux to

0 Lux 233 µs

tDISRC and ISNK Delay Time for Rising Edge (Note 1) RL = 100kΩ, E = 300 lux

from 0 Lux 504 µs

RL = 100kΩ, E = 1000 lux

from 0 Lux 209 µs

ISL29006, ISL29007, ISL29008

4FN6282.1

September 21, 2010

tSISRC and ISNK Delay Time for Falling Edge (Note 1) RL = 100kΩ, E = 300 lux to

0 Lux 30 µs

RL = 100kΩ, E = 1000 lux to

0 Lux 18 µs

VLO Maximum Voltage at EN pin to Enable 0.5 V

VHI Minimum Voltage at EN pin to Disable VDD - 0.5 V

ILO Input Current at EN pin V EN = 0V 1 nA

IHI Input Current at EN pin V EN = 3V 1 nA

tEN Enable Time RL = 100kΩ, E = 100 lux 19 µs

tDIS Disable Time RL = 100kΩ, E = 100 lux 202 µs

NOTE:

1. Switching time measurement is based on Figures 1 and 2.

Electrical Specifications VDD = 3V, TA = +25°C, RL = 100kΩ, green LED light, unless otherwise specified. (Continued)

PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT

FIGURE 1. TEST CIRCUIT FOR RISE/FALL TIME

MEASUREMENT FIGURE 2. TIMING DIAGRAM

ISL29006

FUNCTION

GENERATOR

VCC

VOUT

POWER SUPPL Y

SOURCE METER

INPUT

LIGHT

OUTPUT

10% 90% trtf%

10%

90%

Typical Performance Curves

FIGURE 3. SPECTRAL RESPONSE FIGURE 4. SPECTRUM OF LIGHT SOURCES

-0.2

0.0

0.2

0.4

0.6

0.8

1.0

1.2

300 400 600 800 1.0k

WAVELENGTH (nm)

NORMALIZED RESPONSE

LIGHT SENSOR RESPONSE

HUMAN EYE RESPONSE

1.1k 0

0.2

0.4

0.6

0.8

1.0

1.2

300 400 500 600 700 800 900 1000 1100

WAVELENGTH (nm)

NORMALIZED LIGHT INTENSITY

SUN

HALOGEN

INCANDESCENT

WLED

FLUORESCENT

ISL29006, ISL29007, ISL29008

5FN6282.1

September 21, 2010

FIGURE 5. RADIATION PATTERN FIGURE 6. OUTPUT CURRENT vs LIGHT INTENSITY

FIGURE 7. OUTPUT CURRENT vs LIGHT INTENSITY FIGURE 8. OUTPUT CURRENT vs LIGHT INTENSITY

FIGURE 9. OUTPUT CURRENT vs LIGHT INTENSITY FIGURE 10. RATIO OF SOURCE CURRENT AND SINK

CURRENT vs LIGHT INTENSITY

Typical Performance Curves (Continued)

RADIATION PATTERN

LUMINOSITY

ANGLE

RELATIVE SENSITIVITY

90°

80°

70°

60°

50°

40°

30° 20° 10° 0° 10° 20° 30° 40°

50°

60°

70°

80°

90°

0.2 0.4 0.6 0.8 1.0 0

100

120

140

160

180

200

220

240

260

280

300

320

340

360

380

400

0 2000 4000 6000 8000 10000 12000 14000 16000 18000 20000

LIGHT INTENSITY (LUX)

OUTPUT CURRENT (µA)

VDD = 3V

FLUORESCENT LIGHT

FLUORESCENT

INCANDESCENT

HALOGEN

100

120

140

160

180

200

1000 2000 3000 4000 5000 6000 7000 8000 9000 10000

LIGHT INTENSITY (LUX)

OUTPUT CURRENT (µA)

FLUORESCENT

HALOGEN

INCANDESCENT

0 100 200 300 400 500 600 700 800 900 1000

LIGHT INTENSITY (LUX)

OUTPUT CURRENT (µA)

FLUORESCENT

INCANDESCENT

HALOGEN

FLUORESCENT

HALOGEN

INCANDESCENT

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

LIGHT INTENSITY (LUX)

OUTPUT CURRENT (µA)

0102030405060708090100

FLUORESCENT

INCANDESCENT

HALOGEN

FLUORESCENT

INCANDESCENT

HALOGEN

0.965

0.970

0.975

0.980

0.985

0.990

0.995

1.000

10 100 1000 10000 100000

LIGHT INTENSITY (LUX)

SOURCE CURRENT/SINK CURRENT

VDD = 3V

FLUORESCENT

ISL29006, ISL29007, ISL29008

6FN6282.1

September 21, 2010

FIGURE 1 1. TRANSIENT TME vs LUX CHANGE FROM/TO 0

LUX FIGURE 12. OUTPUT CURRENT vs TEMPERATURE AT 0 LUX

FIGURE 13. SUPPLY CURRENT vs TEMPERATURE AT 0 LUX FIGURE 14. NORMALIZED OUTPUT CURRENT vs

TEMPERATURE

FIGURE 15. SUPPLY CURRENT vs TEMPERATURE FIGURE 16. NORMALIZED OUTPUT CURRENT vs SUPPLY

VOLTAGE

Typical Performance Curves (Continued)

0.01

0.1

100

1000

1 10 100 1000

LUX CHANGE FROM/TO 0 LUX (LUX)

TRANSIENT TIME (ms)

DELAY TIME BEFORE FAL LING

FALL TIME

DELAY TIME BEFORE RISING

RISE TIME

-0.013

0.013

0.026

0.039

0.052

0.065

0.078

0.091

0.104

0.117

EQUIVALENT LIGHT INTENSITY (LUX)

-0.2

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100

TEMPERATURE (°C)

OUTPUT SOURCE CURRENT (nA)

VDD = 3V

REXT = 10MΩ

LIGHT INTENSITY = 0 LUX

0.10

0.11

0.12

0.13

0.14

0.15

0.16

0.17

0.18

0.19

0.20

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100

TEMPERATURE (°C)

SUPPLY CURRENT (µA)

VDD = 3V

REXT = 10MΩ

LIGHT INTENSITY = 0 LUX

0.97

0.98

0.99

1.00

1.01

1.02

1.03

1.04

1.05

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100

TEMPERATURE (°C)

NORMALIZED OUTPUT CURRENT

1000 LUX

300 LUX

VDD = 3V

FLUORESCENT LIGHT

LINEAR (1000 LUX)

LINEAR (300 LUX)

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100

TEMPERATURE (°C)

SUPPLY CURRENT (µA)

1100 LUX

300 LUX

VDD = 3V

FLUORESCENT LIGHT

ISL29006

0.97

0.98

0.99

1.00

1.01

1.02

1.5 2.0 2.5 3.0 3.5 4.0

SUPPLY VOLTAGE (V)

NORMALIZED OUTPUT CURRENT

FLUORESCENT LIGHT INTENSITY = 850 LUX

ISL29006, ISL29007, ISL29008

7FN6282.1

September 21, 2010

FIGURE 17. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 18. TRANSIENT RESPONSE OF ISL29006 TO

CHANGE IN LIGHT INTENSITY

FIGURE 19. TRANSIENT RESPONSE OF ISL29007 TO CHANGE IN LIGHT INTENSITY

Typical Performance Curves (Continued)

18.0

18.2

18.4

18.6

18.8

19.0

19.2

19.4

19.6

19.8

20.0

1.5 2.0 2.5 3.0 3.5 4.0

SUPPLY VOLTAGE (V)

SUPPLY CURRENT (µA)

FLUORESCENT LIGHT INTENSITY = 850 LUX

VDD = 3V, REXT = 100kΩ

LIGHT INTENSITY RISES FROM 0 TO 300 LUX

AND FALLS FROM 300 TO 0 LUX WITH WHITE

LED

LIGHT INTENSITY

VOUT

VDD = 3V, REXT = 100kΩ

LIGHT INTENSITY RISES FROM 0 TO 300 LUX

AND FALLS FROM 300 TO 0 LUX WITH WHITE

LED

LIGHT INTENSITY

VOUT

ISL29006, ISL29007, ISL29008

8FN6282.1

September 21, 2010

Application Information

Light-to-Current and Voltage Conversion

The ISL29006, ISL29007 and ISL29008 have

responsiveness that is directly proportional to the intensity of

light intercepted by the photodiode arrays. Conversion rate

is independent of the light sources (fluorescent light,

incandescent light or direct sunlight).

Here, IOUT is the output current in µA, and E is the input light

in lux.

For some applications, a load resistor is added between the

output and the ground, as shown in Figu re 1. The output

voltage can be expressed in Equation 2:

Here, VOUT is the output voltage and RL is the value of the

external load resistor. The compliance of the ISL29006's

output circuit may result in prematur e saturation of the

output current and voltage when an excessively large RL is

used. The output compliance voltage is 300mV below the

supply voltage as listed in VO-MAX of the “Electrical

Specifications” table on page 3.

In order to have the line ar relationship between the input

light and the output current and voltage, a proper resistor

value (i.e., gain) should be picked for a specific input light

range. The resistor value can be picked according to

Equation 3:

Here, VSUP is the supply voltage and ERANGE is the specific

input light range for an application. For example, an indoor

light ranges typically from 0 lux to 1,000 lux. A resistor value

of 270kΩ for 3V supply voltage can be used. For a small light

range, a large resistor value should be used to achieve

better sensitivity; for a large lig ht range, a sma ll resistor

value should be used to prevent non-linear output current

and voltage.

Application Examples

The following examples present fro m fully automatic to fully

manual override implementations. These guidelines are

applicable to a wide variety of potential light control

applications. The ISL29006, ISL29007 and ISL29008 can be

used to control the brightness input of CCFL inverters.

Likewise, it can interface well with LED drivers. In each

specific application, it is important to recognize the target

environment and its ambient light conditions. The

mechanical mounting of the sensor, light aperture hole size

and use of a light pipe or bezel are critical in determining the

response of the ambient light detector for a given exposure

of light.

The example in Figure 20 show s a fully automatic dimming

solution with no user interactio n. Choose R1 and R2 values

for any desired minimum brightness and slope. Choose C1

to adjust response time and to filter 50/60Hz room lighting.

For example, suppose you wish to generate an output

voltage from 0.25V to 1.2V to drive the input of an LED driver

controller. The 0.25V repr esents the minimum LED

brightness and 1.2V represents the maximum. The 1st step

would be to determine the ratio of R1 and R2 in Equation 4:

Next, the value of R2 can be calculated based on the

maximum output current coming from the ISL29006 under

the application's maximum light exposure. Suppose the

current has been determined to be about 2µA. Thus, R2 can

be approximately calculated using Equations 5 and 6:

and Equation 6:

In Figure 20, the 3VDC supply can be replaced with a user

adjustable bias control, such as 3V PWM control to allow

control over the minimum and maximum output voltage.

Figure 21 shows that ISL29006 is used to provide automatic

dimming control.

Short Circuit Current Limit

The ISL29006, ISL29007 and ISL29008 do not limit the

output short circuit current. If the output is directly shorted to

the ground continuously, the output current could easily

increase for a strong input light such that the device may be

damaged. Maximum reliability is maintained if the output

continuous current never exceeds 6mA by adding a load

IOUT 1.6μA

100lux

-------------------

⎝⎠

⎛⎞

E×=(EQ. 1)

VOUT IOUT RL

×1.6μA

100lux

-------------------

⎝⎠

⎛⎞

××== (EQ. 2)

RLVSUP 0.3V–()

1.6μA

--------------------------------------- 100lux

ERANGE

------------------------

×=(EQ. 3)

R1R23.0V

0.25V

----------------1–

⎝⎠

⎛⎞

×11 R2

×== (EQ. 4)

3V TO 5V

SUPPLY VOLTAGE 3V DC VOLTAGE

ISL29006ISRC

GND

VDD

TO INVERTER BRIGHTNESS

CONTROLLER

FIGURE 20.

60k 25µF

660k

INPUT OR LED DRIVER

R21.2V

2μA

------------

⎝⎠

⎛⎞

60kΩ== (EQ. 5)

R111 R2

×660kΩ== (EQ. 6)

ISL29006, ISL29007, ISL29008

9FN6282.1

September 21, 2010

resistor at the output. This limit is set by the design of the

internal metal interconnects.

ISL29008 has the capability of both sourcing and sinking

current simultaneously. It may replace ISL29006 in sourcing

current applications, or ISL29007 in sinking current

applications. In applications that requi re both sourcing and

sinking currents, for example in cases of mobile phones or

PDAs where the display brightness needs to be proportional

to ambient brightness while the key pads need to be

inversely proportional to the brightness, ISL29008 offers the

most economical solution for cost and footprint.

Suggested PCB Foo tp rin t

Footprint pads should be a nominal 1-to-1 correspondence

with package pads. Since ambient light sensor devices do

not dissipate high power, heat dissipation through the

exposed pad is not important; instead, similar to DFN or

QFN, the exposed pad provides robustness in the board

mounting process. Therefore, we recommend that the

exposed pad be soldered down for robust joint formation, but

this is not mandatory.

Power Supply Bypassing and Printed Circuit

Board Layout

The ISL29006, ISL29007 and ISL 29008 are relatively

insensitive to the printed circuit board layout due to their low

speed operation. Nevertheless, good printed circuit board

layout is necessary for optimum performance. Ground plane

construction is highly recommended; lead length should be

as short as possible and the power supply pins must be well

bypassed to reduce the risk of oscillation. For normal single

supply operation where the GND pin is connected to ground,

a 0.1µF ceramic capacitor should be placed from the VCC

pin to the GND pin. A 4.7µF tantalum capacitor should then

be connected in parallel, placed close to the device.

Optical Sensor Location Outline

The green area in Figure 22 shows the optical sensor

location outline of ISL29006, ISL29007 and ISL29008 .

Along the pin-out direction, the center line (CL) of the sensor

coincides with that of the packaging. The sensor width in this

direction is 0.39mm. Perpendicular to the pin-out direction,

the CL of the sensor has a 0.19mm offset from the CL of

packaging away from pin-1. The sensor width in this

direction is 0.46mm.

GND

ENABLE

PGND

VIN

EL7630

LED

6.19

22µH

1µF

100k

VIN

ENABLE

1µF

MA2772800LCT-ND

GND

750

VDD

GND

2NC

ISRC 6

ISL29006 LIGHT SENSOR

0.1µF

FIGURE 21. AUTOMATIC DIMMING CONTROL

3EN 4

ILED VFB

RLED

--------------- E1.6μA

100lux

-------------------

⎝⎠

⎛⎞

RLED

--------------- 1+

⎝⎠

⎜⎟

⎛⎞

••–= (EQ. 7)

ISL29006, ISL29007, ISL29008

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without

notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No lice nse is gran t ed by i mpli catio n or other wise u nder an y p a tent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

FN6282.1

September 21, 2010

FIGURE 22. 6 LD ODFN SENSOR LOCATION OUTLINE

2.10mm

2.00mm

0.39mm

0.19mm

0.46mm

ISL29006, ISL29007, ISL29008

11 FN6282.1

September 21, 2010

ISL29006, ISL29007, ISL29008

Package Outline Drawing

L6.2x2.1

6 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN)

Rev 0, 9/06

located within the zone indicated . Th e pin #1 identifier may be

Unless otherwise specified, tol erance : Decim al ± 0.05

Tiebar shown (if present) is a non-functional feature.

The configuration of the pin #1 identifier is optio nal, but must be

between 0.15mm an d 0.3 0m m from the te rminal tip.

Dimension b applies to the metallized terminal and is measured

Dimensions in ( ) for Reference Only.

Dimensioning and tolerancing conform to AMSE Y14.5m-1994 .

either a mold or mark feature.

Dimensions are in millimeters.1.

NOTES:

(4X) 0.10

INDEX AREA

PIN 1

2.10

2.00

SEATING PLANE

BASE PLANE

0.08

0.10

SEE DETAIL "X"

0 . 00 MIN .

DETAIL "X"

0 . 05 MAX.

0 . 2 REF

SIDE VIEW

TYPICAL RECOMMENDED LAND PATTERN

( 6X 0 . 30 )

( 6X 0 . 55 )

TOP VIEW

(0 . 65)

(1 . 95)

(0 . 65) (1 . 35)

BOTTOM VIEW

6X 0 . 35 ± 0 . 05 B0.10 MAC

1 . 35 1 . 30 REF

INDEX AREA

PIN 1

0.65

0 . 65

MAX 0.75

6X 0 . 30 ± 0 . 05