INCH-POUND MIL-DTL-83723/76E 19 August 2009 SUPERSEDING MIL-DTL-83723/76D 15 September 2006 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (BAYONET COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES A, G, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 MIL-DTL-83723/76E Shell size 8 A max G min .312 .352 10 .388 .428 12 .558 .598 14 .627 .667 16 .772 .794 18 .860 .900 20 .985 1.025 22 1.110 1.150 24 1.235 1.275 H J .415 .424 .517 .526 .687 .696 .756 .765 .883 .892 .989 .998 1.114 1.123 1.239 1.248 1.364 1.373 .540 .545 .662 .667 .832 .837 .901 .906 1.028 1.033 1.134 1.139 1.261 1.266 1.384 1.389 1.511 1.516 L min .632 U max V .776 .025 .760 .906 .031 .930 1.078 .031 .999 1.141 .031 1.126 1.266 .031 1.232 1.375 .031 1.357 1.510 .031 1.482 1.625 .031 1.607 1.760 .031 FIGURE 1. Dimensions and configurations - Continued. 2 MIL-DTL-83723/76E Inches mm Inches mm Inches mm Inches mm Inches mm .008 0.20 .177 4.50 .545 13.84 .900 22.86 1.235 31.37 .015 0.38 .182 4.62 .552 14.02 .901 22.89 1.239 31.47 .018 0.46 .185 4.70 .558 14.17 .906 23.01 1.248 31.70 .020 0.51 .198 5.03 .598 15.19 .930 23.62 1.261 32.03 .022 0.56 .200 5.08 .627 15.93 .985 25.02 1.266 32.16 .025 0.64 .204 5.18 .632 16.05 .989 25.12 1.275 32.39 .031 0.79 .211 5.36 .662 16.81 .998 25.35 1.357 34.47 .032 0.81 .259 6.58 .667 16.94 .999 25.37 1.364 34.65 .042 1.07 .312 7.92 .678 17.22 1.025 26.04 1.373 34.87 .046 1.17 .316 8.03 .687 17.45 1.028 19.84 1.375 34.93 .065 1.65 .320 8.13 .696 17.68 1.033 26.24 1.384 35.15 .069 1.75 .330 8.38 .756 19.20 1.110 27.38 1.389 35.28 .084 2.13 .352 8.94 .760 19.30 1.078 28.19 1.482 37.64 .090 2.29 .366 9.30 .765 19.43 1.114 28.30 1.510 38.35 .097 2.46 .383 9.73 .772 19.61 1.123 28.52 1.511 38.38 .101 2.57 .388 9.86 .776 19.71 1.126 28.60 1.516 38.51 .106 2.69 .415 10.54 .794 20.17 1.134 28.80 1.607 40.82 .112 2.84 .424 10.77 .832 21.13 1.139 28.93 1.625 41.28 .125 3.18 .428 10.87 .837 21.26 1.411 28.98 1.760 44.70 .138 3.51 .517 13.13 .860 21.84 1.150 29.21 .144 3.66 .526 13.36 .883 22.43 1.230 31.24 .170 4.32 .540 13.72 .892 22.66 1.232 31.29 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1o for all angles. 4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 5. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. 3 MIL-DTL-83723/76E REQUIREMENTS: Dimensions and configurations: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities. Shell size 8 10 Insert arrangements 03 06 Contact cavities 1, 2, 3 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049. This connector mates with MIL-DTL-83723/71 and /73. Part or Identifying Number (PIN) example: M83723/ 76 W 22 55 N Military designator Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/71 MIL-DTL-83723/73 MIL-STD-1554 SAE-AS85049 4 MIL-DTL-83723/76E CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC Review activities: Army - AR, MI Navy - EC Air Force - 19 (Project 5935-2008-158) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 5