FTR-K1 SERIES COMPACT HIGH POWER RELAY 1 POLE - 40A (For Automotive Applications) FBR53-HW Series n FEATURES l l l l l l Small 40A relay High temperature grade (-40C to 125C) Contact arrangement Form U (form A) Surface mount compatible (reflow capability) Inrush current 80A Coil wire temperature class: H n PARTNUMBER INFORMATION [Example] FBR53 (a) N (b) D12 (c) - Y (d) - HW (e) (a) Relay type FBR53 : FBR53 Series (b) Enclosure N (c) Coil rated voltage D12 : Plastic sealed type : 9.....12 VDC Coil rating table at page 3 (d) Contact material Y : Silver-tin oxide (e) Contact rating HW : 40A Actual marking does not carry the type name: "FBR" E.g.: Ordering code: FBR53ND12-Y-HW Actual marking: 53ND12-Y-HW 1 FTR-K1 SERIES FBR53-HW SERIES n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation FBR53-HW Configuration Form U Material Silver-tin oxide (AgSnO2) Voltage drop Max. 100 mV at 1A, at 12V open contact voltage Average 1.2m at 7A, 12VDC Contact rating 40A , 14VDC (resistive load) Max. carrying current 40A Max. inrush current 80A inrush Min. switching load * 6 VDC, 1A Mechanical Min. 10 x 106 operations (without contact load) Electrical Min. 100 x 103 operations (14VDC, 20A resistive load) Rated power 860 mW Operate power 310 mW Operating temperature range -40 C to +125 C (no frost) Coil wire temperature class H Operate (at nominal voltage) Max. 10 ms Release (at nominal voltage) Max. 10 ms (no diode) Resistance (initial) Min. 100 M Dielectric strength Other Vibration resistance Shock Terminal Open contacts 500 VAC (50/60 Hz) 1min. Contacts to coil 500 VAC (50/60 Hz) 1min. Misoperation 10 to 55Hz double amplitude 1.5mm, direction X, Y, Z Endurance 10 to 100Hz double amplitude 1.5mm, direction X, Y, Z No damage (mechanical and electrical) after test. Coil energizing: 1 hr each direction, Coil not energized: 1 hr each direction Misoperation 100m/s (11ms), direction X, Y, Z Endurance 1,000m/s (11ms), direction X, Y, Z, each 6 shocks No damage (mechanical and electrical) after test. Coil energizing: 3 shocks Coil not energized: 3 shocks, total 36 shocks Solderability At 270 10C for 3 0.5sec. Strength 9.8N (1 Kgf) Pull force, longitudinal during 10 sec. Weight Approximately 6 g Sealing Plastic sealed cat III * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 SERIES FBR53-HW SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * D09 9 94 5.4 0.7 7.7 (at 125 C) 1.0 (at 125 C) 6.3 0.8 9 (at 125 C) 1.2 (at 125 C) 7.3 1.0 10.4 (at 125 C) 1.5 (at 125 C) D10 D12 10 12 117 167 Note: All values in the table are valid for 20C and zero contact current, unless otherwise indicated. * Specified operate values are valid for pulse wave voltage. n CHARACTERISTIC DATA 3 FTR-K1 SERIES FBR53-HW SERIES n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) l l PC board mounting hole layout (BOTTOM VIEW) Tube carrier (pokayoke) Unit: mm 4 FBR53-HW SERIES FTR-K1 SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All automotive relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our automotive relays are lead-free. Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 5 FBR53-HW SERIES FTR-K1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2012 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. March 19, 2012 6