General-purpose Operational Amplifiers / Comparators SIGNATURE SERIES Operational Amplifiers LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Description The Universal Standard family LM358 / 324, LM2904 / 2902 monolithic ICs integrate two independent op-amps and phase compensation capacitors on a single chip and feature high-gain, low power consumption, and an operating voltage range of 3[V] to 32[V] (single power supply.) No.11094EBT05 SIGNATURE SERIES Dual LM358 family LM358DT LM358PT LM358ST LM358WDT LM358WPT Quad LM2902 family LM324 family LM2904 family LM2904DT LM2904PT LM2904ST LM2904WDT LM2904WPT LM324DT LM324PT LM324WDT LM2902DT LM2902PT LM2902WDT Features 1) Operating temperature range 0[] to + 70[] Commercial Grade LM358/324 family : Extended Industrial Grade LM2904/2902 family : -40[] to +125[] 2) Wide operating supply voltage +3[V] to +32[V] (single supply) 1.5[V] to 16[V] (dual supply) 3) Low supply current 4) Common-mode input voltage range including ground 5) Differential input voltage range equal to maximum rated supply voltage 6) High large signal voltage gain 7) Wide output voltage range Pin Assignment OUTPUT 1 OUTPUT 1 INVERTING INPUT 1 1 2 NON-INVERTING INPUT 1 3 Vcc 4 SO package8 LM358DT LM358WDT LM2904DT LM2904WDT 8 Vcc INVERTING INPUT 1 NON-INVERTING INPUT 1 7 OUTPUT 2 6 NON-INVERTING LM358PT LM358WPT LM2904PT LM2904WPT www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 2 14 3 Vcc 4 INVERTING INPUT 2 5 INPUT 2 TSSOP8 1 NON-INVERTING INPUT 2 INVERTING INPUT 2 OUTPUT 2 11 Vcc 5 6 7 SO package14 Mini SO8 LM358ST LM2904ST LM324DT LM324WDT LM2902DT LM2902WDT 1/17 OUTPUT 4 INVERTING 13 INPUT 4 NON-INVERTING 12 INPUT 4 NON-INVERTING 10 INPUT 3 INVERTING 9 INPUT 3 8 OUTPUT 3 TSSOP14 LM324PT LM2902PT 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Absolute Maximum Ratings (Ta=25[]) Parameter Symbol Supply Voltage VDD Operating Temperature Range Topr Rating LM358 family LM324 family LM2904 family LM2902 family +32 Unit V 0 to +70 -40 to +125 Storage Temperature Range Tstg -65 to +150 Input Common-mode Voltage VICM -0.3 to +32 V Maximum Junction Temperature Tjmax +150 Electric Characteristics LM358,LM324 family(Unless otherwise specified, Vcc+=+5[V], Vcc-=0[V]) Limit Parameter Temperature Symbol range Input Offset Voltage (*1) VIO Input Offset Current (*1) IIO Input Bias Current (*1) IIB LM358 family LM324 family Min. Typ. Max. Min. Typ. Max. 25 2 7 7 Full range 9 9 25 2 30 2 30 Full range 100 25 20 150 20 150 Full range 200 300 Unit Conditions Fig. No mV VO=1.4[V],RS=0[] 5[V]< Vcc+<30[V] 0<VIC< Vcc+-1.5[V] 98 nA VO=1.4[V] 98 nA VO=1.4[V] 98 + Large Signal Voltage Gain AVD Supply Voltage Rejection Ratio SVR Supply Current (All Amp) ICC Input Common-mode Voltage Range VICM Common-mode Rejection Ratio CMR Output Short Circuit Current (*2) Output Sink Current (*2) 25 25 100 25 65 100 Full range 65 25 100 65 110 65 Vcc =15[V] V/mV VO=1.4[V] to 11.4[V] RL=2[k] dB 25 0.7 1.2 Vcc =5[V],No Load 25 1.5 3 Vcc+=30[V],No Load Full range 0.7 1.2 0.8 3 Full range 2 1.5 3 25 Vcc -1.5 + Vcc -1.5 Full range Vcc -2.0 + Vcc -2.0 mA Vcc =30[V],No Load + V Vcc+=30[V] 98 dB RS10[k] 98 Vcc+=15[V],VO=+2[V] VID=+1[V] 99 VO=+2[V], Vcc+=15[V],VID=-1[V] VO=+0.2[V], Vcc+=15[V] ,VID=-1[V] 99 V RL=2[k] 99 V Vcc+=30[V],RL=10[k] 99 RL=10[k] 99 70 85 70 80 60 Isource 25 20 40 60 20 40 70 mA 10 20 10 20 mA Isink 25 12 50 12 50 A VOH Low Level Output Voltage VOL Slew Rate 99 + 60 High Level Output Voltage Vcc+=5[V],No Load + 25 Vopp 98 + Full range Output Voltage Swing RS10[k] Vcc+=5[V] to 30[V] 98 25 0 Vcc+-1.5 Full range 0 Vcc+-2.0 25 27 28 27 28 Full range 27 27 25 5 20 5 20 Full range 20 20 SR 25 0.6 0.4 Gain Bandwidth Product GBP 25 1.1 1.3 Total Harmonic Distortion THD 25 0.02 0.015 en 25 55 40 nV/ Hz Input Offset Voltage Drift DVIO 7 7 V/ Input Offset Current Drift DIIO 10 10 pA/ VO1/VO2 25 120 120 dB Input Equivalent Noise Voltage Channel Separation mV RL=2[k],CL=100[pF], Vcc+=15[V] VI=0.5[V] to 3[V], Unity Gain Vcc+=30[V],RL=2[k], MHz CL=100[pF] VIN=10[mV],f=100[kHz] f=1[kHz],AV=20[dB] RL=2[k] CL=100[pF],VO=2[Vpp] V/s f=1[kHz],RS=100[] Vcc+=30[V] 1[kHz]f20[kHz] 99 99 99 99 99 (*1) Absolute value (*2) Under high temperatures, please consider the power dissipation when selecting the output current. When output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 2/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note LM2904,LM2902 family(Unless otherwise specified, Vcc+=+5[V], Vcc-=0[V]) Limit Parameter Symbol Temperature range LM2904 family Min. Input Offset Voltage (*3) VIO Input Offset Current (*3) IIO Input Bias Current (*3) IIB Large Signal Voltage Gain AVD Supply Voltage Rejection Ratio SVR Supply Current (All Amp) Input Common-mode Voltage Range ICC VICM Common-mode Rejection Ratio CMR Output Short Circuit Current (*4) Isource Typ. LM2902 family Max. Min. Typ. Unit Conditions Fig. No Max. 25 2 7 2 7 Full range 9 9 25 2 50 2 30 Full range 200 200 25 20 150 20 150 Full range 200 300 25 25 100 25 100 mV VO=1.4[V] 98 nA VO=1.4[V] 98 nA VO=1.4[V] 98 Vcc+=15[V] V/mV VO=1.4[V] to 11.4[V] RL=2[k] 25 65 100 65 110 Full range 65 65 25 0.7 1.2 0.7 1.2 25 1.5 3 Full range 2 0.8 1.2 Vcc+=5[V],No Lord Full range 1.5 3 Vcc+=30[V],No Lord + + 25 Vcc -1.5 Vcc -1.5 Full range Vcc+-2.0 Vcc+-2.0 25 70 85 70 80 Full range 60 60 25 20 40 60 20 40 70 dB RS10[k] 98 99 Vcc+=5[V],No Lord mA Vcc+=30[V],No Lord 99 V Vcc+=30[V] 98 dB RS=10[k] 98 mA Vcc+=+15[V],VO=+2[V] VID=+1[V] 98 + Output Sink Current (*4) Isink Output Voltage Swing Vopp High Level Output Voltage VOH Low Level Output Voltage VOL 10 20 10 20 mA 12 50 12 50 A 25 0 Vcc+-1.5 Full range 0 Vcc+-2.0 25 27 27 28 Full range 27 28 27 25 V V VO=2[V],Vcc =+5[V] VID=-1[V] VO=+0.2[V], Vcc+=+15[V] ,VID=-1[V] 99 RL=2[k] 99 Vcc+=30[V],RL=10[k] Vcc+=30[V],RL=10[k] 99 25 5 20 5 20 Full range 20 20 SR 25 0.6 0.4 Gain Bandwidth Product GBP 25 1.1 1.3 Total Harmonic Distortion THD 25 0.02 0.015 en 25 40 nV/ Hz Input Offset Voltage Drift DVIO 7 7 V/ - Input Offset Current Drift DIIO 10 10 pA/ - VO1/VO2 25 120 120 dB Slew Rate Input Equivalent Noise Voltage Channel Separation mV RL=10[k] 99 RL=2[k],CL=100[pF], Unity Gain VI=0.5[V] to 3[V] Vcc+=1.5[V] Vcc+=30[V],RL=2[k] MHz CL=100[pF] VIN=10[mV] f=1[kHz],AV=20[dB] RL=2[k] CL=100[pF], Vcc+=30[V],VO=2[Vpp] V/s f=1[kHz],RS=100[] Vcc+=30[V] 1[kHz]f20[kHz] 99 99 99 99 99 (*3) Absolute value (*4) Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 3/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM358 family LM358 family POWER DISSIPATION Pd [mW] 800 LM358 family LM358 family LM358PT LM358WPT LM358ST 600 25 LM358DT LM358WDT 32V 0 400 200 5V 70 3V 0 70 0 25 50 75 100 AMBIENT TEMPERATURE : [] Ta [] Fig. 1 Derating Curve Fig. 2 Supply Current - Supply Voltage LM358 family Fig. 3 Supply Current - Ambient Temperature LM358 family LM358 family 0 0 25 70 25 70 Fig. 4 Maximum Output Voltage - Supply Voltage (RL=10[k]) Fig. 5 Maximum Output Voltage - Ambient Temperature (VCC=5[V],RL=2[k]) Fig. 6 Output Source Current - Output Voltage (VCC=5[V]) LM358 family LM358 family LM358 family 15V 70 3V 5V 0 3V 5V 15V 25 Fig. 7 Output Source Current - Ambient Temperature (VOUT=0[V]) Fig. 8 Output Sink Current - Output Voltage (VCC=5[V]) Fig. 9 Output Sink Current - Ambient Temperature (VOUT=VCC) LM358 family LM358 family LM358 family 32V 25 0 0 5V 25 3V 70 70 Fig. 10 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) Fig. 11 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) Fig. 12 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 4/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM358 family LM358 family LM358 family LM358 family 3V 5V 32V 25 0 32V 3V 5V 70 Fig. 13 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) Fig. 14 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) Fig. 15 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM358 family LM358 family LM358 family 70 0 25 0 25 70 [V] Fig. 16 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) Fig. 17 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) Fig. 18 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM358 family LM358 family LM358 family 0 15V 25 3V 5V 5V 32V 70 Fig. 19 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) Fig. 20 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM358 family LM358 family 36V 0 Fig. 21 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM358 family 32V 25 70 Fig. 22 Common Mode Rejection Ratio - Supply Voltage 5V 3V Fig. 23 Common Mode Rejection Ratio - Ambient Temperature Fig. 24 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 5/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM324 family LM324family family BA2904 LM324 family family BA2904 LM324 family 1000 POWER DISSIPATION Pd [mW] LM324ST LM324DT LM324WDT 800 32V 25 600 0 400 5V 200 70 3V 0 0 25 70 50 75 100 AMBIENT TEMPERATURE :[] Ta [] Fig. 25 Derating Curve Fig. 26 Supply Current - Supply Voltage LM324 family Fig. 27 Supply Current - Ambient Temperature LM324 family LM324 family 0 0 25 70 25 70 Fig. 28 Maximum Output Voltage - Supply Voltage (RL=10[k]) Fig. 29 Fig. 30 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) LM324 family LM324 family LM324 family 15V 70 3V 5V 0 5V 15V 3V 25 Fig. 31 Output Source Current - Ambient Temperature (VOUT=0[V]) Fig. 32 Output Sink Current - Output Voltage (VCC=5[V]) Fig. 33 Output Sink Current - Ambient Temperature (VOUT=VCC) LM324 family LM324 family LM324 family 32V 0 25 0 25 5V 3V 70 70 Fig. 34 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) Fig. 35 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) Fig. 36 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 6/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM324 family LM324 family 3V 25 0 5V LM324 family LM324 family 32V 32V 3V 5V 70 Fig. 37 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) Fig. 38 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) Fig. 39 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM324 family LM324 family LM324 family 0 70 25 0 25 70 [V] Fig. 40 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) Fig. 41 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) Fig. 42 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) LM324 family LM324 family LM324 family 25 0 15V 3V 5V 5V 32V 70 Fig. 43 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) Fig. 44 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM324 family LM324 family 36V 0 Fig. 45 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM324 family 32V 25 5V 70 Fig. 46 Common Mode Rejection Ratio - Supply Voltage 3V Fig. 47 Common Mode Rejection Ratio - Ambient Temperature Fig. 48 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 7/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM2904 family LM2904 family LM2904 family LM2904 family 1.0 800 1.0 LM2904DT LM2904WDT 400 200 SUPPLY CURRENT [mA] LM2904ST 600 0.8 SUPPLY CURRENT [mA] POWER DISSIPATION Pd [mW] LM2904PT LM2904WPT 25 40 0.6 0.4 0 125 105 0.2 25 50 75 100 125 0.4 5V 3V 0.0 0 150 32V 0.6 0.2 0.0 0 0.8 10 AMBIENT TEMPERATURE : [] Ta [] Fig. 49 Derating Curve 20 30 SUPPLY VOLTAGE [V] -50 40 Fig. 50 Supply Current - Supply Voltage LM2904 family 40 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 51 Supply Current - Ambient Temperature LM2904 family 5 -25 LM2904 family 50 -40 30 125 20 25 105 10 0 4 3 2 1 10 20 30 40 25 30 105 20 10 Fig. 52 Maximum Output Voltage - Supply Voltage (RL=10[k]) 0 1 LM2904 family 100 15V 5V 30 15V 20 10 0 OUTPUT SINK CURRENT [mA] OUTPUT SINK CURRENT [mA] 3V 10 125 1 -40 0.1 25 0.01 0 25 50 75 100 125 150 0 0.4 AMBIENT TEMPERATURE [] Fig. 55 Output Source Current - Ambient Temperature (VOUT=0[V]) 25 60 50 40 125 105 30 20 10 5 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 57 Output Sink Current - Ambient Temperature (VOUT=VCC) LM2904 family 8 70 60 5V 50 40 3V 30 20 10 0 0 0 -25 32V LOW LEVEL SINK CURRENT [A] 70 3V 10 -50 LM2904 family 80 -40 5V 2 Fig. 56 Output Sink Current - Output Voltage (VCC=5[V]) LM2904 family 80 0.8 1.2 1.6 OUTPUT VOLTAGE [V] INPUT OFFSET VOLTAGE [mV] -25 20 0 0.001 -50 5 LM2904 family 30 105 40 2 3 4 OUTPUT VOLTAGE [V] Fig. 53 Fig. 54 Maximum Output Voltage - Ambient Temperature Output Source Current - Output Voltage (VCC=5[V],RL=2[k]) (VCC=5[V]) LM2904 family 50 125 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] SUPPLY VOLTAGE [V] LOW LEVEL SINK CURRENT [A] 40 0 0 OUTPUT SOURCE CURRENT [mA] OUTPUT SOURCE CURRENT [mA] MAXIMUM OUTPUT VOLTAGE [V] MAXIMUM OUTPUT VOLTAGE [V] -40 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 58 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) 6 -40 25 4 2 0 -2 105 125 -4 -6 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 59 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) 0 5 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 60 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 8/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM2904 family LM2904 family 8 LM2904 family 50 3V 2 0 5V -2 32V -4 40 30 20 10 105 40 32V 30 20 3V 10 5V 125 0 0 -25 0 25 50 75 0 100 125 150 AMBIENT TEMPERATURE [] Fig. 61 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) 30 20 10 0 30 -50 35 -10 6 -40 25 125 2 0 -2 -4 -6 0 25 50 75 100 125 150 -1 0 AMBIENT TEMPERATURE [] Fig. 64 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) 3V 0 5V 32V -5 4 -10 130 -40 25 120 110 100 90 105 0 25 50 75 125 80 70 100 125 150 6 8 10 12 SUPPLY VOLTAGE [V] 25 100 80 125 105 60 40 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 70 Common Mode Rejection Ratio - Supply Voltage 40 20 25 30 35 LM2904 family 140 130 15V 120 110 100 5V 90 80 70 14 -50 16 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 69 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM2904 family COMMON MODE REJECTION RATIO [dB] -40 120 15 Fig. 66 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) Fig. 68 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM2904 family 140 10 60 4 AMBIENT TEMPERATURE [] Fig. 67 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 5 SUPPLY VOLTAGE [V] 140 36V 120 100 80 5V 3V 60 40 -50 -25 LM2904 family 140 32V 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 71 Common Mode Rejection Ratio - Ambient Temperature POWER SUPPLY REJECTION RATIO [dB] -25 125 105 -5 0 60 -50 0 5 LM2904 family 140 LARGE SIGNAL VOLTAGE GAIN [dB] 5 25 -40 Fig. 65 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) LM2904 family 10 1 2 3 [V] INPUT VOLTAGE [Vin] LARGE SIGNAL VOLTAGE GAIN [dB] -25 5 -10 -8 -50 LM2904 family 10 105 4 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 63 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM2904 family 8 INPUT OFFSET VOLTAGE [mV] 40 10 15 20 25 SUPPLY VOLTAGE [V] Fig. 62 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) LM2904 family 50 5 INPUT OFFSET CURRENT [nA] -50 INPUT BIAS CURRENT[nA] 25 -40 -6 INPUT OFFSET CURRENT [nA] INPUT BIAS CURRENT [nA] 4 INPUT BIAS CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 6 -8 COMMON MODE REJECTION RATIO [dB] LM2904 family 50 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 72 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 9/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM2902 family LM2902 family LM2902 family 1000 1.0 1.0 0.8 0.8 LM2902 family SUPPLY CURRENT [mA] 600 400 LM2902DT LM2902WDT 200 SUPPLY CURRENT [mA] POWER DISSIPATION Pd [mW] LM2902ST 800 25 40 0.6 0.4 0.2 0 125 105 25 50 75 100 125 5V 3V 0.0 0 150 0.4 0.2 0.0 0 32V 0.6 10 AMBIENT TEMPERATURE : [] Ta [] Fig. 73 Derating Curve 20 30 SUPPLY VOLTAGE [V] -50 40 Fig. 74 Supply Current - Supply Voltage LM2902 family 40 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 75 Supply Current - Ambient Temperature LM2902 family 5 -25 LM2902 family 50 -40 30 125 20 25 105 10 0 4 3 2 1 10 20 30 40 25 30 105 20 Fig. 76 Maximum Output Voltage - Supply Voltage (RL=10[k]) 0 0 Fig. 77 Maximum Output Voltage - Ambient Temperature (VCC=5[V],RL=2[k]) LM2902 family 50 125 10 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] SUPPLY VOLTAGE [V] LM2902 family 100 1 5V 30 15V 20 10 15V 10 125 1 -40 0.1 25 0.01 0 25 50 75 100 125 150 0 0.4 AMBIENT TEMPERATURE [] Fig. 79 Output Source Current - Ambient Temperature (VOUT=0[V]) 25 60 50 40 105 30 125 20 10 5 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 81 Output Sink Current - Ambient Temperature (VOUT=VCC) LM2902 family 8 70 60 5V 50 40 3V 30 20 10 0 0 0 -25 32V LOW LEVEL SINK CURRENT [A] 70 3V 10 -50 LM2902 family 80 -40 5V 2 Fig. 80 Output Sink Current - Output Voltage (VCC=5[V]) LM2902 family 80 0.8 1.2 1.6 OUTPUT VOLTAGE [V] INPUT OFFSET VOLTAGE [mV] -25 20 0 0.001 -50 5 LM2902 family 30 OUTPUT SINK CURRENT [mA] OUTPUT SINK CURRENT [mA] 3V 40 2 3 4 OUTPUT VOLTAGE [V] Fig. 78 Output Source Current - Output Voltage (VCC=5[V]) 105 0 LOW LEVEL SINK CURRENT [A] 40 0 0 OUTPUT SOURCE CURRENT [mA] OUTPUT SOURCE CURRENT [mA] MAXIMUM OUTPUT VOLTAGE [V] MAXIMUM OUTPUT VOLTAGE [V] -40 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 82 Low Level Sink Current - Supply Voltage (VOUT=0.2[V]) 6 -40 25 4 2 0 -2 105 125 -4 -6 -8 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 83 Low Level Sink Current - Ambient Temperature (VOUT=0.2[V]) 0 5 10 15 20 25 SUPPLY VOLTAGE [V] 30 35 Fig. 84 Input Offset Voltage - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 10/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Reference Data LM2902 family LM2902 family 8 LM2902 family 50 3V 2 0 5V -2 32V -4 40 -40 20 10 105 40 32V 30 20 3V 10 5V 125 0 0 -25 0 25 50 75 0 100 125 150 AMBIENT TEMPERATURE [] Fig. 85 Input Offset Voltage - Ambient Temperature (Vicm=0[V], VOUT=1.4[V]) 30 20 10 0 30 -50 35 -10 6 -40 4 125 2 0 -2 -4 -6 0 25 50 75 100 125 150 -1 0 AMBIENT TEMPERATURE [] Fig. 88 Input Bias Current - Ambient Temperature (VCC=30[V],Vicm=28[V],VOUT=1.4[V]) 3V 0 5V 32V -5 4 -10 130 -40 25 120 110 100 90 125 105 0 25 50 75 80 70 100 125 150 6 8 10 12 SUPPLY VOLTAGE [V] 25 100 125 80 105 60 40 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 94 Common Mode Rejection Ratio - Supply Voltage 40 20 25 30 35 LM2902 family 140 130 15V 120 110 100 5V 90 80 70 14 -50 16 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 93 Large Signal Voltage Gain - Ambient Temperature (RL=2[k]) LM2902 family COMMON MODE REJECTION RATIO [dB] -40 120 15 Fig. 90 Input Offset Current - Supply Voltage (Vicm=0[V],VOUT=1.4[V]) Fig. 92 Large Signal Voltage Gain - Supply Voltage (RL=2[k]) LM2902 family 140 10 60 4 AMBIENT TEMPERATURE [] Fig. 91 Input Offset Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) 5 SUPPLY VOLTAGE [V] 140 36V 120 100 80 5V 3V 60 40 -50 -25 LM2902 family 140 32V 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 95 Common Mode Rejection Ratio - Ambient Temperature POWER SUPPLY REJECTION RATIO [dB] -25 125 105 -5 0 60 -50 0 5 LM2902 family 140 LARGE SIGNAL VOLTAGE GAIN [dB] 5 25 -40 Fig. 89 Input Offset Voltage - Common Mode Input Voltage (VCC=5[V]) LM2902 family 10 1 2 3 [V] INPUT VOLTAGE [Vin] LARGE SIGNAL VOLTAGE GAIN [dB] -25 5 -10 -8 -50 LM2902 family 10 105 25 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 87 Input Bias Current - Ambient Temperature (Vicm=0[V],VOUT=1.4[V]) LM2902 family 8 INPUT OFFSET VOLTAGE [mV] 40 10 15 20 25 SUPPLY VOLTAGE [V] Fig. 86 Input Bias Current - Supply Voltage (Vicm=0[V], VOUT=1.4[V]) LM2902 family 50 5 INPUT OFFSET CURRENT [nA] -50 INPUT BIAS CURRENT[nA] 25 30 -6 INPUT OFFSET CURRENT [nA] INPUT BIAS CURRENT [nA] 4 INPUT BIAS CURRENT [nA] INPUT OFFSET VOLTAGE [mV] 6 -8 COMMON MODE REJECTION RATIO [dB] LM2902 family 50 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [] Fig. 96 Power Supply Rejection Ratio - Ambient Temperature (*)The data above is ability value of sample, it is not guaranteed. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 11/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Circuit Diagram + Vcc INVERTING INPUT OUTPUT NON-INVERTING INPUT - Vcc Fig.97 Circuit Diagram (each Op-Amp) Measurement Circuit 1 NULL Method Measurement Condition Parameter VF S1 S2 S3 + - Vcc , Vcc , EK, Vicm Unit: [V] LM358/LM324 family LM2904/LM2902 family Calculation Vcc+ Vcc- EK Vicm Vcc+ Vcc- EK Vicm Input Offset Voltage VF1 ON ON OFF 5 to 30 0 -1.4 0 5 to 30 0 -1.4 0 1 Input Offset Current VF2 OFF OFF OFF 5 0 -1.4 0 5 0 -1.4 0 2 VF3 OFF ON 5 0 -1.4 0 5 0 -1.4 0 5 0 -1.4 0 5 0 -1.4 0 15 0 -1.4 0 15 0 -1.4 0 15 0 -11.4 0 15 0 -11.4 0 5 0 -1.4 0 5 0 -1.4 0 5 0 -1.4 3.5 5 0 -1.4 3.5 5 0 -1.4 0 5 0 -1.4 0 30 0 -1.4 0 30 0 -1.4 0 Input Bias Current VF4 ON OFF VF5 Large Signal Voltage Gain VF6 Common-mode Rejection Ratio VF7 VF8 VF9 Supply Voltage Rejection Ratio VF10 OFF ON ON ON ON ON OFF ON ON OFF Calculation 1. Input Offset Voltage (VIO) 3 4 5 6 0.1[F] VF1 Vio 1+ Rf /Rs [V] Rf 50[k] 2. Input Offset Current (IIO) 500[k] Iio VF2 - VF1 [A] Ri (1+ Rf / Rs) S1 Vcc+ 0.1[F] VOUT EK +15[V] 3. Input Bias Current (IIB) Rs VF4 - VF3 [A] Ib 2x Ri (1+ Rf / Rs) Vicm 4. Large Signal Voltage Gain (AVD) 500[k] 50[] 10[k] 50[] 10[k] Rs DUT S3 Ri 1000[pF] AV 20x Log 10x (1+ Rf /Rs) [dB] VF6 - VF5 S2 Rf 5.Common-mode Rejection Ration (CMRR) (1+ Rf/ Rs) CMRR 20x Log 3.5x VF8-VF7 Ri Vcc- RL -15[V] V VF 50[k] [dB] 6. Supply Voltage Rejection Ration (SVR) PSRR 20xLog Vcc +x(1+Rf/Rs) VF10 - VF9 Fig.98 Measurement circuit1 (Each Op-Amps) [dB] Vcc +=25V www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 12/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Measurement circuit2 Switch condition SW 1 SW No. SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8 SW 9 SW 10 SW 11 SW 12 SW 13 SW 14 SW 15 Supply Current OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF High level Output Voltage OFF OFF ON OFF OFF OFF ON OFF OFF ON OFF OFF OFF ON OFF Low level Output Voltage OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON OFF Output source current OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Output sink current OFF OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON Slew Rate OFF OFF OFF ON OFF OFF OFF OFF ON Gain band width product OFF ON OFF OFF OFF ON Equivalent input noise voltage ON OFF OFF OFF ON OFF ON OFF OFF OFF OFF ON OFF OFF OFF ON ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF OFF Input voltage 3[V] SW4 SW5 R2 SW6 R3 0.5[V] Vcc + Input waveform A Output voltage SW1 SW2 RS R1 SR V / t 3[V] SW3 t SW10 SW11 SW12 SW13 SW14 SW15 SW7 SW8 SW9 Vcc - V A VIN- RL VIN+ CL V t V VOUT 0.5[V] t Output waveform Fig.99 Measurement circuit2 (Each Op-Amps) Fig.100 Slew Rate Input Waveform Measurement Circuit3 Channel Separation R2=100[k] R2=100[k] + Vcc =+2.5[V] Vcc+ =+2.5[V] R1=1[k] R1=1[k] other CH CH1 VIN V R1//R2 Vcc- =-2.5[V] VOUT1 =0.5 [Vrms] R1//R2 VO1/VO2=20xlog Vcc-=-2.5[V] V VOUT2 100xVOUT1 VOUT2 Fig.101 Measurement Circuit3 www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 13/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms Please note that item names, symbols and their meanings may differ from those on another manufacturer's documents. 1.Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (Vcc+/Vcc-) Expresses the maximum voltage that can be supplied between the positive and negative supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (VID) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (VICM) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the characteristics or damage to the IC itself. Normal operation is not guaranteed within the common-mode voltage range of the maximum ratings - use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating and storage temperature ranges (Topr,Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25). For packaged products, Pd is determined by the maximum junction temperature and the thermal resistance. 2. Electrical characteristics 2.1 Input offset voltage (VIO) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0 V. 2.2 Input offset voltage drift (DVIO) Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation. 2.3 Input offset current (IIO) Indicates the difference of input bias current between the non-inverting and inverting terminals. 2.4 Input offset current drift (DIIO) Signifies the ratio of the input offset current fluctuation to the ambient temperature fluctuation. 2.5 Input bias current (IIB) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.6 Circuit current (ICC) Indicates the current of the IC itself that flows under specified conditions and during no-load steady state. 2.7 High level output voltage/low level output voltage (VOH/VOL) Signifying the voltage range that can be output under specified load conditions, it is in general divided into high level output voltage and low level output voltage. High level output voltage indicates the upper limit of the output voltage, while low level output voltage the lower limit. 2.8 Large signal voltage gain (AVD) The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AVD = (output voltage fluctuation) / (input offset fluctuation) 2.9 Input common-mode voltage range (VICM) Indicates the input voltage range under which the IC operates normally. 2.10 Common-mode rejection ratio (CMRR) Signifies the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change in input common-mode voltage) / (input offset fluctuation) 2.11 Power supply rejection ratio (SVR) Denotes the ratio of fluctuation of the input offset voltage when supply voltage is changed (DC fluctuation). SVR = (change in power supply voltage) / (input offset fluctuation) 2.12 Output source current/ output sink current (IOH/IOL) The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source current indicates the current flowing out of the IC, and the output sink current the current flowing into the IC. 2.13 Channel separation (VO1/VO2) Expresses the amount of fluctuation of the input offset voltage or output voltage with respect to the change in the output voltage of a driven channel. 2.14 Slew rate (SR) Indicates the time fluctuation ratio of the output voltage when an input step signal is supplied. 2.15 Gain bandwidth product (GBP) The product of the specified signal frequency and the gain of the op-amp at such frequency, it gives the approximate value of the frequency where the gain of the op-amp is 1 (maximum frequency, and unity gain frequency). www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 14/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Derating curves 1000 LM358PT LM358WPT LM2904PT LM2904WPT POWER DISSIPATION Pd [mW] POWER DISSIPATION Pd [mW] 800 LM358ST 600 LM2904ST LM2904DT LM2904WDT 400 LM358DT LM358WDT 200 0 0 25 70 50 75 LM2902ST 800 LM2902DT LM2902WDT 600 LM324PT 400 LM324DT LM324WDT 200 0 100 125 150 0 AMBIENT TEMPERATURE [] 25 50 70 75 100 125 150 AMBIENT TEMPERATURE [] LM358DR/PWR/DGKR LM2904DR/PWR/DGKR/VQDR/VQPWR LM324DR/PWR/KDR LM2902DR/PWR/KDR/KPWR/KQDR/KQPWR Power Dissipation Power Dissipation Pd[W] ja [/W] Package Pd[W] ja [/W] SO package8 (*8) 450 3.6 SO package14 610 4.9 TSSOP8 (*6) 500 4.0 TSSOP14 870 7.0 Mini SO8 (*7) 470 3.76 Package Fig.102 Derating Curves Precautions Vcc + 1) Unused circuits When there are unused circuits, it is recommended that they be connected as in Fig.103, setting the non-inverting input terminal to a potential within the in-phase input voltage range (VICM). 2) Input terminal voltage Applying Vcc- + 32V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 3) Power supply (single / dual) The op-amp operates when the voltage supplied is between Vcc+ and Vcc-. Therefore, the single supply op-mp can be used as a dual supply op-amp as well. connect to Vicm Vcc - Fig.103 Disable circuit example 4) Power dissipation (Pd) Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to the rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign substances between the outputs, the output and the power supply, or the output and Vcc- may result in IC destruction. 6) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 7) Radiation This IC is not designed to withstand radiation. 8) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo) effects. 9) IC operation The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of Vcc+ and Vcc-, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output terminal and Vcc-, and increasing the bias current for Class A operation will suppress crossover distortion. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage. 11) Output capacitor Discharge of the external output capacitor to Vcc+ is possible via internal parasitic elements when Vcc+ is shorted to Vcc-, causing damage to the internal circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation due to output capacitive load does not occur, such as in voltage comparators, use an output capacitor with a capacitance less than 0.1F. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 15/17 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note Ordering part number L M 2 9 0 2 Family name LM358 LM324 LM2902 LM2904 W D ESD Tolerance applicable T Package type D : S.O package P : TSSOP S : Mini SO W : 2kV None : Normal Packaging and forming specification R: Embossed tape and reel S.O package8 <Tape and Reel information> 4.90.2 (MAX 5.25 include BURR) 6 5 0.45Min. 7 3.90.2 6.00.3 8 4 +6 -4 1 2 3 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 4 0.545 0.20.1 0.175 1.3750.1 S 1.27 0.420.1 1pin 0.1 S Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. S.O package14 <Tape and Reel information> 8.650.1 (Max 9.0 include BURR) 0.65 0.15 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 1PIN MARK 0.175 0.075 S +0.05 0.22 -0.03 1.375 0.075 1.65MAX 0.515 1.050.2 8 6.0 0.2 3.9 0.1 14 4 +6 -4 +0.05 0.42 -0.04 1.27 0.08 S 0.08 M 1pin Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. TSSOP8 <Tape and Reel information> 3.00.1 (MAX 3.35 include BURR) 7 6 0.5 0.15 3 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand 4 1PIN MARK The direction is the 1pin of product is at the upper left when you hold ) 1.00.2 2 Embossed carrier tape Quantity +0.05 0.145 -0.03 0.1 0.05 S 1.0 0.05 1.2MAX 1 0.525 Tape 5 6.4 0.2 4.4 0.1 8 44 0.08 S +0.05 0.245 -0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. Reel 16/17 Direction of feed Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT LM324DT/PT/WDT,LM2902DT/PT/WDT Technical Note TSSOP14 <Tape and Reel information> 5.00.1 (Max 5.35 include BURR) 4 4 14 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 1PIN MARK +0.05 0.145 -0.03 0.10.05 S 1.00.05 1.2MAX 0.55 1.00.2 0.50.15 6.40.2 4.40.1 8 0.08 S +0.05 0.245 -0.04 0.65 0.08 1pin M Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. Mini SO8 <Tape and Reel information> 3.00.1 (MAX 3.35 include BURR) 6 5 0.45 0.15 2 3 4 1PIN MARK Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 0.95 0.2 1 +0.05 0.145 -0.03 0.525 0.10.05 S 0.850.05 1.1MAX 7 3.0 0.1 4.9 0.2 8 44 0.08 S +0.05 0.32 -0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. Reel 17/17 Direction of feed Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. R1120A