Thyristors 25 Amp Standard SCRs SK225xD Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits * RoHS compliant * Voltage capability up to 1200 V * Surge capability up to 300 A Applications Agency Recognitions Agency * Electrically isolated package "LD -Package" and UL Recognized for 2500VRMS Typical applications are AC solid-state switches, industrial power tools, line rectification 50/60Hz. Agency File Number E71639 Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol Main Features Symbol Value Unit IT(RMS) 25 A VDRM / VRRM 1200 V IGT 40 mA A K G (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 Thyristors 25 Amp Standard SCRs Absolute Maximum Ratings -- 25A SCR Symbol Parameter VDRM /VRRM Repetitive Peak off-state/Reverse Voltage Test Conditions VDSM/VRSM Non-repetitive peak off-state/Reverse voltage IT(RMS) RMS on-state current IT(AV) Average on-state current ITSM Peak non-repetitive surge current SK225LD TC=75C SK225RD TC=95C SK225LD TC=75C SK225RD TC=95C Value Unit 1200 V 1300 V 25 A 16 A single half cycle; f = 50Hz; TJ (initial) = 25C 300 single half cycle; f = 60Hz; TJ (initial) = 25C 360 A I2t I2t Value for fusing tp = 8.3 ms 540 A 2s di/dt Critical rate of rise of on-state current IGM Peak gate current TJ = 125C 50 3 A/s A PG(AV) Average gate power dissipation TJ = 125C 1 W Tstg Storage temperature range -40 to 150 C TJ Operating junction temperature range -40 to 125 C Notes : x = package Electrical Characteristics (TJ = 25C, unless otherwise specified) Symbol IGT VGT dv/dt VGD IH tq tgt Test Conditions VD = 12V; RL = 30 VD = 2/3 VDRM; gate open; TJ = 125C Value Unit mA MAX. 40 MAX. 1.5 V MIN. 1000 V/s VD = VDRM; RL = 3.3 k; TJ = 125C MIN. 0.2 V IT = 500mA (initial) MAX. 100 mA TYP. 15 s TYP. 3 s IT=0.5A; tp=50s; dv/dt=5V/s; di/dt=-30A/s IG = 2 x IGT; PW = 15s; IT = 50A Notes : x = package Static Characteristics Symbol VTM IDRM / IRRM Test Conditions Value IT = 50A; tp = 380s MAX. TJ = 25C VDRM / VRRM TJ = 125C MAX. Unit 1.6 V 10 A 4 mA Thermal Resistances Symbol R(JC) Parameter Junction to case (AC) Value SK225RD 1.0 SK225LD 1.9 Unit C/W (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 Thyristors 25 Amp Standard SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: N ormalized DC Gate Trigger Voltage vs. Junction Temperature 2.5 2.0 1.6 Ration of VGT /VGT (TJ= 25 o C) Ration of IGT /IGT (TJ = 25 o C) 2.0 1.5 1.0 0.5 0.0 1.2 0.8 0.4 -40 -15 10 35 60 85 0.0 110 125 Junction Temperature (TJ)-(o C) Intantaneous On-state Current (iT) - Amps Ration of I H /IH (TJ= 25 o C) 1.2 0.8 0.4 60 85 110 80 70 60 50 40 30 20 10 0 -40 -15 10 35 60 Junction Temperature 85 110 125 Instantaneous On-state Voltage (vT) - Volts Figure 6: M aximum Allowable Case Temperature vs. RMS On-State Current Maximum Allowable Case Temperature (TC) - C 30 25 20 15 10 5 5 10 15 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 (TJ)-(o C) Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Average On-State Power Dissipation [PD(AV)] - (Watts) 35 90 1.6 0 10 Figure 4: O n-State Current vs. On-State Voltage (Typical) 2.0 0 -15 Junction Temperature (TJ)-(o C) Figure 3: Normalized DC Holding Current vs. Junction Temperature 0.0 -40 20 RMS On-State Current [IT(RMS)] - (Amps) 25 130 120 SK225RD 110 100 90 SK225LD 80 70 60 50 40 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 0 10 20 30 RMS On-State Current [IT(RMS)] - Amps (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 Thyristors 25 Amp Standard SCRs Maximum Allowable Case Temperature (TC) - C Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current 130 SK225RD 120 110 100 90 SK225LD 80 70 60 50 40 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 0 2 4 6 8 10 12 14 16 18 Average On-State Current [IT(AVE)] - Amps Peak Surge (Non-repetitive)On-state Current (ITSM) - Amps Figure 8: Surge Peak On-State Current vs. Number of Cycles SUPPLY FREQUENCY: 50 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature 350 tp=10ms One cycle 300 250 Notes: 1. G ate control may be lost during and immediately following surge current interval. 2. O verload may not be repeated until junction temperature has returned to steady-state rated value. 200 150 100 50 0 1 10 100 1000 Surge Current Duration - Full Cycles Environmental Specifications Test Specifications and Conditions AC Blocking JESD22-A108C, 80% VDRM @125C for 168 hours Temperature Cycling MIL-STD-750, M-1051, 100 cycles; -40C to +150C; 15-min dwell-time Temperature/Humidity EIA / JEDEC, JESD22-A101 168 hours; 100V - DC: 85C; 85% rel humidity Resistance to Solder Heat JESD22-B106C Solderability J-STD-022, category 3, test A Physical Specification Terminal Finish 100% Matte Tin-Plated Body Material UL Recognized compound meeting flammability rating V-0 Design Considerations Careful selection of the correct component for the application's operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 Thyristors 25 Amp Standard SCRs Dimensions -- TO-220AB (RD-Package) -- Non-Isolated Mounting Tab Common with Center Lead Dimension m .8m 3 ax E OM H D V1 L3 F ANODE A C2 L1 C3 Millimeters Min. C B G Max. 0.173 0.181 B 0.61 0.88 0.024 0.035 C 0.46 0.70 0.018 0.028 C2 1.21 1.32 0.048 0.052 C3 2.40 2.72 0.094 0.107 D 8.60 9.70 0.339 0.382 E 9.60 10.4 0.378 0.409 F 6.20 6.60 0.244 0.260 2.54 28.0 0.1 29.8 1.102 3.75 1.173 0.148 L2 1.14 1.70 0.045 L3 2.65 2.95 0.104 45 V1 Note: Maximum torque to be applied to mounting tab is 3 in-lbs (0.3Nm). Typ. 4.60 H GATE Min. 4.40 L1 CATHODE ANODE Inches Max. A G L2 Typ. 0.067 0.116 45 Dimensions -- TO-220AB (LD-Package) -- Isolated Mounting Tab Dimension A m .8m 3 ax E OM C2 H D V1 L3 F ANODE A L1 C3 Millimeters Min. 4.40 G B C Note: Maximum torque to be applied to mounting tab is 7 in-lbs. (0.8 Nm). 4.60 0.173 Typ. Max. 0.181 0.61 0.88 0.024 0.035 0.46 0.70 0.018 0.028 C2 1.21 1.32 0.048 0.052 C3 2.40 2.72 0.094 0.107 D 8.60 9.70 0.339 0.382 E 9.80 10.4 0.386 0.409 F 6.55 6.95 0.258 H GATE Min. B 2.54 28.0 29.8 1.102 L2 1.14 1.70 0.045 2.65 2.95 0.104 45 1.173 0.148 L3 V1 0.274 0.1 3.75 L1 CATHODE ANODE Inches Max. C G L2 Typ. 0.067 0.116 45 (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19 Thyristors 25 Amp Standard SCRs Product Selector Part Number Gate Sensitivity Type Package SK225LD 40mA Standard SCR TO-220L SK225RD 40mA Standard SCR TO-220R Packing Options Part Number Marking Weight Packing Mode Base Quantity SK225LDTP SK225LD 2.2g Tube 1000 SK225RDTP SK225RD 2.0g Tube 1000 Part Numbering System Part Marking System S K2 25 LD TP DEVICE TYPE S: SCR VOLTAGE RATING K2: 1200V CURRENT RATING 25: 25A PACKAGING TYPE TP: Tube Pack PACKAGE TYPE LD: TO-220 Isolated RD: TO-220 Non-Isolated SK225RD YMMXXX (R) Date Code Marking Y:Year Code MM: Month Code XXX: Lot Trace Code Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. (c) 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/18/19