DS90LV001 DS90LV001 800 Mbps LVDS Buffer Literature Number: SNLS067D DS90LV001 800 Mbps LVDS Buffer General Description The DS90LV001 LVDS-LVDS Buffer takes an LVDS input signal and provides an LVDS output signal. In many large systems, signals are distributed across backplanes, and one of the limiting factors for system speed is the "stub length" or the distance between the transmission line and the unterminated receivers on individual cards. Although it is generally recognized that this distance should be as short as possible to maximize system performance, real-world packaging concerns often make it difficult to make the stubs as short as the designer would like. The DS90LV001, available in the LLP (Leadless Leadframe Package) package, will allow the receiver to be placed very close to the main transmission line, thus improving system performance. A wide input dynamic range will allow the DS90LV001 to receive differential signals from LVPECL as well as LVDS sources. This will allow the device to also fill the role of an LVPECL-LVDS translator. An output enable pin is provided, which allows the user to place the LVDS output in TRI-STATE. The DS90LV001 is offered in two package options, an 8 pin LLP and SOIC. Features Single +3.3 V Supply LVDS receiver inputs accept LVPECL signals TRI-STATE outputs Receiver input threshold < 100 mV Fast propagation delay of 1.4 ns (typ) Low jitter 800 Mbps fully differential data path 100 ps (typ) of pk-pk jitter with PRBS = 223-1 data pattern at 800 Mbps Compatible with ANSI/TIA/EIA-644-A LVDS standard 8 pin SOIC and space saving (70%) LLP package Industrial Temperature Range Connection Diagram Top View 10133805 Order Number DS90LV001TM, DS90LV001TLD See NS Package Number M08A, LDA08A Block Diagram 10133802 (c) 2008 National Semiconductor Corporation 101338 www.national.com DS90LV001 800 Mbps LVDS Buffer February 19, 2008 DS90LV001 Maximum Package Power Dissipation at 25C M Package 726 mW Derate M Package 5.8 mW/C above +25C LDA Package 2.44 W Derate LDA Package 19.49 mW/C above +25C ESD Ratings Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) LVCMOS/LVTTL Input Voltage (EN) LVDS Receiver Input Voltage (IN +, IN-) LVDS Driver Output Voltage (OUT +, OUT-) LVDS Output Short Circuit Current Junction Temperature Storage Temperature Range Lead Temperature Range Soldering (4 sec.) -0.3V to +4V -0.3V to (VCC + 0.3V) 2.5kV 250V (HBM, 1.5k, 100pF) (EIAJ, 0, 200pF) -0.3V to +4V Recommended Operating Conditions -0.3V to +4V Continuous +150C -65C to +150C Supply Voltage (VCC) Receiver Input Voltage Operating Free Air Temperature +260C Min 3.0 0 -40 Typ 3.3 +25 Max 3.6 VCC +85 Units V V C Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. (Notes 2, 3) Symbol Parameter Conditions Min Typ Max Units VCC V LVCMOS/LVTTL DC SPECIFICATIONS (EN) VIH High Level Input Voltage 2.0 VIL Low Level Input Voltage 0.8 V IIH High Level Input Current VIN = 3.6V or 2.0V, VCC = 3.6V +7 +20 A IIL Low Level Input Current VIN = GND or 0.8V, VCC = 3.6V 1 10 A VCL Input Clamp Voltage ICL = -18 mA -0.6 -1.5 V 325 450 mV 20 mV 1.375 V 20 mV 1 10 A GND LVDS OUTPUT DC SPECIFICATIONS (OUT) VOD Differential Output Voltage RL = 100 VOD Change in Magnitude of VOD for Complimentary Output States Figure 1 and Figure 2 VOS Offset Voltage RL = 100 VOS Change in Magnitude of VOS for Complimentary Output States Figure 1 IOZ Output TRI-STATE Current EN = 0V, VOUT = VCC or GND IOFF Power-Off Leakage Current VCC = 0V, VOUT = 3.6V or GND 1 10 A IOS Output Short Circuit Current (Note 4) EN = VCC, VOUT+ and VOUT- = 0V -16 -24 mA IOSD Differential Output Short Circuit Current (Note 4) EN = VCC, VOD = 0V -7 -12 mA 0 +100 mV 250 1.080 1.19 LVDS RECEIVER DC SPECIFICATIONS (IN) VTH Differential Input High Threshold VTL Differential Input Low Threshold VCM = +0.05V, +1.2V or +3.25V VCMR Common Mode Voltage Range VID = 100mV, VCC = 3.3V IIN Input Current VIN = +3.0V IIN Change in Magnitude of IIN -100 0 3.25 V 1 10 A 1 10 A 1 6 A VIN = 0V 1 6 A VCC = 3.6V or 0V VIN = 0V VIN = +3.0V VCC = 3.6V or 0V 0.05 mV SUPPLY CURRENT ICCD Total Supply Current EN = VCC, RL = 100, CL = 5 pF 47 70 mA ICCZ TRI-STATE Supply Current EN = 0V 22 35 mA www.national.com 2 Over recommended operating supply and temperature ranges unless otherwise specified. (Note 3) Symbol Min Typ Max Units tPHLD Differential Propagation Delay High to Low Parameter RL = 100, CL = 5pF Conditions 1.0 1.4 2.0 ns tPLHD Differential Propagation Delay Low to High Figure 3 and Figure 4 1.0 1.4 2.0 ns tSKD1 Pulse Skew |tPLHD - tPHLD| (Notes 5, 6) 20 200 ps tSKD3 Part to Part Skew (Notes 5, 7) 0 tSKD4 Part to Part Skew (Notes 5, 8) tLHT Rise Time (Note 5) RL = 100, CL = 5pF 200 tHLT Fall Time (Note 5) Figure 3 and Figure 5 200 tPHZ Disable Time (Active High to Z) RL = 100, CL = 5pF tPLZ Disable Time (Active Low to Z) Figure 6 and Figure 7 tPZH Enable Time (Z to Active High) tPZL Enable Time (Z to Active Low) tDJ LVDS Data Jitter, Deterministic (Peak-to-Peak) (Note 9) VID = 300mV; PRBS = 223 - 1 data; VCM = 1.2V at 800Mbps (NRZ) tRJ LVDS Clock Jitter, Random (Note 9) VID = 300mV; VCM = 1.2V at 400MHz clock 60 ps 400 ps 320 450 ps 310 450 ps 3 25 ns 3 25 ns 25 45 ns 25 45 ns 100 135 ps 2.2 3.5 ps Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD and VOD. Note 3: All typical are given for VCC = +3.3V and TA = +25C, unless otherwise stated. Note 4: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. Note 5: The parameters are guaranteed by design. The limits are based on statistical analysis of the device performance over the PVT (process, voltage and temperature) range. Note 6: tSKD1, |tPLHD - tPHLD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. Note 7: tSKD3, Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same VCC and within 5C of each other within the operating temperature range. Note 8: tSKD4, Part to Part Skew, is the differential channel-to- channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max - Min| differential propagation delay. Note 9: The parameters are guaranteed by design. The limits are based on statistical analysis of the device performance over the PVT range with the following test equipment setup: HP8133A (pattern pulse generator), 5 feet of RG142B cable with DUT test board and HP83480A (digital scope mainframe) with HP83484A (50GHz scope module). The HP8133A with RG142B cable exhibit a tDJ = 21ps and tRJ = 1.8ps. 3 www.national.com DS90LV001 AC Electrical Characteristics DS90LV001 DC Test Circuits 10133803 FIGURE 1. Differential Driver DC Test Circuit 10133808 FIGURE 2. Differential Driver Full Load DC Test Circuit AC Test Circuits and Timing Diagrams 10133806 FIGURE 3. LVDS Output Load 10133807 FIGURE 4. Propagation Delay Low-to-High and High-to-Low www.national.com 4 DS90LV001 10133809 FIGURE 5. LVDS Output Transition Time 10133801 FIGURE 6. TRI-STATE Delay Test Circuit 10133804 FIGURE 7. Output active to TRI-STATE and TRI-STATE to active output time 5 www.national.com DS90LV001 DS90LV001 Pin Descriptions (SOIC and LLP) Pin Name Pin # Input/Output GND 1 P Ground Description IN - 2 I Inverting receiver LVDS input pin IN+ 3 I Non-inverting receiver LVDS input pin NC 4 VCC 5 P Power Supply, 3.3V 0.3V. No Connect OUT+ 6 O Non-inverting driver LVDS output pin OUT - 7 O Inverting driver LVDS output pin EN 8 I Enable pin. When EN is LOW, the driver is disabled and the LVDS outputs are in TRI-STATE. When EN is HIGH, the driver is enabled. LVCMOS/LVTTL levels. DAP NA NA Die Attach Pad or DAP (LLP Package only). The DAP is NOT connected to the device GND nor any other pin. It is still recommended to connect the DAP to a GND plane of a PCB for enhenced heat dissipation. Typical Applications Backplane Stub-Hider Application 10133811 www.national.com 6 DS90LV001 Cable Repeater Application 10133810 PCB LAYOUT AND POWER SYSTEM BYPASS Circuit board layout and stack-up for the DS90LV001 should be designed to provide noise-free power to the device. Good layout practice also will separate high frequency or high level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic capacitance of the PCB power system which improves power supply filtering, especially at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 F to 0.1 F. Tantalum capacitors may be in the range 2.2 F to 10 F. Voltage rating for tantalum capacitors should be at least 5X the power supply voltage being used. It is recommended practice to use two vias at each power pin of the DS90LV001 as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance by up to half, thereby reducing interconnect inductance and extending the effective frequency range of the bypass components. The outer layers of the PCB may be flooded with additional ground plane. These planes will improve shielding and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally, to be effective, these planes must be tied to the ground supply plane at frequent intervals with vias. Frequent via placement also improves signal integrity on signal transmission lines by providing short paths for image currents which reduces signal distortion. The planes should be pulled back from all transmission lines and component mounting pads a distance equal to the width of the widest transmission line or the thickness of the dielectric separating the transmission line from the internal power or ground plane(s) whichever is greater. Doing so minimizes effects on transmission line impedances and reduces unwanted parasitic capacitances at component mounting pads. There are more common practices which should be followed when designing PCBs for LVDS signaling. Please see application note AN-1108 for guidelines. In addition, application note AN-1187 has additional information specifically related to LLP recommendations. Application Information MODE OF OPERATION The DS90LV001 can be used as a "stub-hider." In many systems, signals are distributed across backplanes, and one of the limiting factors for system speed is the "stub length" or the distance between the transmission line and the unterminated receivers on the individual cards. Although it is generally recognized that this distance should be as short as possible to maximize system performance, real-world packaging concerns and PCB designs often make it difficult to make the stubs as short as the designer would like. The DS90LV001, available in the LLP (Leadless Leadframe Package) package, can improve system performance by allowing the receiver to be placed very close to the main transmission line either on the backplane itself or very close to the connector on the card. Longer traces to the LVDS receiver may be placed after the DS90LV001. This very small LLP package is a 75% space savings over the SOIC package. INPUT FAILSAFE The receiver inputs of the DS90LV001 do not have internal failsafe biasing. For point-to-point and multidrop applications with a single source, failsafe biasing may not be required. When the driver is off, the link is in-active. If failsafe biasing is required, this can be accomplished with external high value resistors. Using the equations in the LVDS Owner"s Manual Chapter 4, the IN+ should be pull to VCC (3.3V) with 20k and the IN- should be pull to GND with 12k. This provides a slight positive differential bias, and sets a known HIGH state on the link with a minimum amount of distortion. 10133815 7 www.national.com DS90LV001 Typical Performance Curves Output High Voltage vs Power Supply Voltage Output Low Voltage vs Power Supply Voltage 10133816 10133817 Output Short Circuit Current vs Power Supply Voltage Differential Output Short Circuit Current vs Power Supply Voltage 10133818 10133819 www.national.com 8 DS90LV001 Output TRI-STATE Current vs Power Supply Voltage Offset Voltage vs Power Supply Voltage 10133820 10133821 Differential Output Voltage vs Power Supply Voltage Differential Output Voltage vs Load Resistor 10133822 10133823 Power Supply Current vs Frequency Power Supply Current vs Power Supply Voltage 10133825 10133824 9 www.national.com DS90LV001 TRI-STATE Power Supply Current vs Power Supply Voltage Differential Transition Voltage vs Power Supply Voltage 10133827 10133826 Differential Propagation Delay vs Power Supply Voltage Differential Propagation Delay vs Ambient Temperature 10133828 www.national.com 10133836 10 DS90LV001 Differential Skew vs Power Supply Voltage Differential Skew vs Ambient Temperature 10133829 10133837 Transition Time vs Power Supply Voltage Transition Time vs Ambient Temperature 10133830 10133838 11 www.national.com DS90LV001 Differential Propagation Delay vs Differential Input Voltage Differential Propagation Delay vs Common-Mode Voltage 10133831 10133832 Peak-to-Peak Output Jitter at VCM = 0.4V vs Differential Input Voltage Peak-to-Peak Output Jitter at VCM = 2.9V vs Differential Input Voltage 10133833 www.national.com 10133835 12 Peak-to-Peak Output Jitter at VCM = 1.2V vs Ambient Temperature 10133834 10133839 13 www.national.com DS90LV001 Peak-to-Peak Output Jitter at VCM = 1.2V vs Differential Input Voltage DS90LV001 Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS90LV001TM See NS Package Number M08A Order Number DS90LV001TLD See NS Package Number LDA08A www.national.com 14 DS90LV001 Notes 15 www.national.com DS90LV001 800 Mbps LVDS Buffer Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated