KSZ8041FTLI TR - Micrel - Datasheet.Directory

KSZ8041TL/FTL

10Base-T/100Base-TX/100Base-FX

Physical Layer Transceiver

Data Sheet Rev. 1.1

LinkMD is a registered trademark of Micrel, Inc.

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

April 2007 M9999-042707-1.1

General Description

The KSZ8041TL is a single supply 10Base-T/100Base-TX

Physical Layer Transceiver, which provides MII/RMII/SMII

interfaces to transmit and receive data. It utilizes a unique

mixed-signal design to extend signaling distance while

reducing power consumption.

HP Auto MDI/MDI-X provides the most robust solution for

eliminating the need to differentiate between crossover

and straight-through cables.

Micrel LinkMD® TDR-based cable diagnostics permit

identification of faulty copper cabling.

The KSZ8041TL represents a new level of features and

performance and is an ideal choice of physical layer

transceiver for 10Base-T/100Base-TX applications.

The KSZ8041FTL has all the identical rich features of the

KSZ8041TL plus 100Base-FX support for fiber and media

converter applications.

Both KSZ8041TL and KSZ8041FTL are available in 48-

pin, lead-free TQFP packages (See Ordering Informat ion).

Data sheets and support documentation can be found on

Micrel’s web site at: www.micrel.com.

Functional Diagram

Micrel, Inc. KSZ8041TL/FTL

April 2007 2 M9999-042707-1.1

Features

• Single-chip 10Base-T/100Base -TX physical layer

solution

• Fully compliant to IEEE 802.3u Standard

• Low power CMOS design, power consumption of

<180mW

• HP auto MDI/MDI-X for reliable detection and corre ction

for straight-through and crossover cables with disa ble

and enable option

• Robust operation over standard cables

• LinkMD® TDR-based cabl e diagnostics for identification

of faulty copper cabling

• Fiber support: 100Base-FX (KSZ8041 FTL only), Back-

to-Back mode (KSZ8041FTL and KSZ8 041TL)

• MII interface support

• RMII interface support with external 50MHz system

clock

• SMII interface support with external 125MHz system

clock and 12.5MHz syn c clock from MAC

• MIIM (MDC/MDIO) manageme nt bus to 12.5MHz for

rapid PHY register configu ration

• Interrupt pin option

• Programmable LED outputs for link, activity and speed

• Power down and power saving modes

• Single power supply (3.3V)

• Built-in 1.8V regulator for core

• Available in 48-pin TQFP package

Applications

• Printer

• LOM

• Game Console

• IPTV

• IP Phone

• IP Set-top Box

• Media Converter

Ordering Information

Part Number Temp. Range Package Lead Finish

KSZ8041TL 0°C to 70°C 48-Pin TQFP Pb-Free

KSZ8041TLI(1) -40°C to 85°C 48-Pin TQFP Pb-Free

KSZ8041FTL 0°C to 70°C 48-Pin TQFP Pb-Free

KSZ8041FTLI(1) -40°C to 85°C 48-Pin TQFP Pb-Free

Note:

1. Contact factory for lead time.

Micrel, Inc. KSZ8041TL/FTL

April 2007 3 M9999-042707-1.1

Revision History

Revision Date Summary of Changes

1.0 12/21/06 Data sheet created.

1.1 4/27/07 Added maximum MDC clock speed.

Added 40K +/-30% to note 1 of Pin Descri pti on and Strapping Options tables for interna l pull-ups/pull-

downs.

Changed Model Number in Register 3 h – PHY Identifier 2.

Changed polarity (swapped definition) of DUPLEX strapping pin.

Removed DUPLEX strapping pin update to Register 4h – Auto-Negotiation Advertisement bits [8, 6].

Added Back-to-Back mode for KSZ8041TL.

Added Symbol Error to MII/RMII Receive Error description and Register 15h – RXER Counter.

Added a 100pF capacitor on REXT (pin 16) in Pin Description table.

Micrel, Inc. KSZ8041TL/FTL

April 2007 4 M9999-042707-1.1

Contents

Pin Configuration..................................................................................................................................................................8

Pin Description....................................................................................................................................................................10

Strapping Options...............................................................................................................................................................15

Functional Description.......................................................................................................................................................17

100Base-TX Transmit.......................................................................................................................................................17

100Base-TX Receive........................................................................................................................................................17

PLL Clock Synthesizer......................................................................................................................................................17

Scrambler/De-scrambler (100Base-TX only)....................................................................................................................17

10Base-T Transmit...........................................................................................................................................................17

10Base-T Receive............................................................................................................................................................18

SQE and Jabber Function (10Base-T only)......................................................................................................................18

Auto-Negotiation...............................................................................................................................................................18

MII Management (MIIM) Interface....................................................................................................................................20

Interrupt (INTRP)..............................................................................................................................................................20

MII Data Interface.............................................................................................................................................................20

MII Signal Definition..........................................................................................................................................................21

Transmit Clock (TXC).................................................................................................................................................21

Transmit Enable (TXEN).............................................................................................................................................21

Transmit Data [3:0] (TXD[3:0])...................................................................................................................................21

Receive Clock (RXC)..................................................................................................................................................21

Receive Data Valid (RXDV)........................................................................................................................................22

Receive Data [3:0] (RXD[3:0])....................................................................................................................................22

Receive Error (RXER).................................................................................................................................................22

Carrier Sense (CRS) ...................................................................................................................................................22

Collision (COL) ...........................................................................................................................................................22

Reduced MII (RMII) Data Interface...................................................................................................................................22

RMII Signal Definition.......................................................................................................................................................23

Reference Clock (REF_CLK) .....................................................................................................................................23

Transmit Enable (TX_EN)...........................................................................................................................................23

Transmit Data [1:0] (TXD[1:0])...................................................................................................................................23

Carrier Sense/Receive Data Valid (CRS_DV)...........................................................................................................23

Receive Data [1:0] (RXD[1:0])....................................................................................................................................23

Receive Error (RX_ER)...............................................................................................................................................23

Collision Detection.....................................................................................................................................................24

Serial MII (SMII) Data Interface........................................................................................................................................24

SMII Signal Definition .......................................................................................................................................................24

Clock Reference (CLOCK).........................................................................................................................................24

Sync Pulse (SYNC).....................................................................................................................................................24

Transmit Data and Control (TX) ................................................................................................................................24

Receive Data and Control (RX)..................................................................................................................................25

Collision Detection.....................................................................................................................................................26

HP Auto MDI/MDI-X..........................................................................................................................................................27

Straight Cable .............................................................................................................................................................27

Crossover Cable.........................................................................................................................................................28

LinkMD® Cable Diagnostics..............................................................................................................................................29

Access.........................................................................................................................................................................29

Usage...........................................................................................................................................................................29

Micrel, Inc. KSZ8041TL/FTL

April 2007 5 M9999-042707-1.1

Power Management..........................................................................................................................................................29

Power Saving Mode....................................................................................................................................................29

Power Down Mode......................................................................................................................................................29

Reference Clock Connection Options ..............................................................................................................................30

Reference Circuit for Power and Ground Connections....................................................................................................31

100Base-FX Fiber Operation (KSZ8041FTL only)...........................................................................................................32

Fiber Signal Detect.....................................................................................................................................................32

Far-End Fault...............................................................................................................................................................32

Back-to-Back Media Converter.........................................................................................................................................33

MII Back-to-Back Mode..............................................................................................................................................33

RMII Back-to-Back Mode............................................................................................................................................34

Register Map........................................................................................................................................................................35

Register Description...........................................................................................................................................................35

Absolute Maximum Ratings(1) ............................................................................................................................................43

Operating Ratings(2) ............................................................................................................................................................43

Electrical Characteristics(3) ................................................................................................................................................43

Timing Diagrams.................................................................................................................................................................45

MII SQE Timing (10Base-T) .............................................................................................................................................45

MII Transmit Timing (10Base-T).......................................................................................................................................46

MII Receive Timing (10Base-T)........................................................................................................................................47

MII Transmit Timing (100Base-TX) ..................................................................................................................................48

MII Receive Timing (100Base-TX) ...................................................................................................................................49

RMII Timing.......................................................................................................................................................................50

Auto-Negotiation Timing...................................................................................................................................................51

MDC/MDIO Timing ...........................................................................................................................................................52

Reset Timing.....................................................................................................................................................................53

Reset Circuit........................................................................................................................................................................54

Selection of Isolation Transformer....................................................................................................................................56

Selection of Reference Crystal..........................................................................................................................................56

Package Information...........................................................................................................................................................57

Micrel, Inc. KSZ8041TL/FTL

April 2007 6 M9999-042707-1.1

List of Figures

Figure 1. Auto-Negotiation Flow Chart.................................................................................................................................19

Figure 2. SMII Transmit Data/Control Segment...................................................................................................................25

Figure 3. SMII Receive Data/Control Segment....................................................................................................................26

Figure 4. Typical Straight Cable Connection .......................................................................................................................27

Figure 5. Typical Crossover Cable Connection ...................................................................................................................28

Figure 6. 25MHz Crystal / Oscillator Reference Clock for MII Mode...................................................................................30

Figure 7. 50MHz Oscillator Reference Clock for RMII Mode...............................................................................................30

Figure 8. 125MHz Oscillator Reference Clock for SMII Mode.............................................................................................30

Figure 9. KSZ8041TL/FTL Power and Ground Connections...............................................................................................31

Figure 10. KSZ8041FTL / KSZ8041TL Back-to-Back Media Converter..............................................................................33

Figure 11. MII SQE Timing (10Base-T) ...............................................................................................................................45

Figure 12. MII Transmit Timing (10Base-T).........................................................................................................................46

Figure 13. MII Receive Timing (10Base-T)..........................................................................................................................47

Figure 14. MII Transmit Timing (100Base-TX).....................................................................................................................48

Figure 15. MII Receive Timing (100Base-TX)......................................................................................................................49

Figure 16. RMII Timing – Data Received from RMII............................................................................................................50

Figure 17. RMII Timing – Data Input to RMII.......................................................................................................................50

Figure 18. Auto-Negotiation Fast Link Pulse (FLP) Timing .................................................................................................51

Figure 19. MDC/MDIO Timing..............................................................................................................................................52

Figure 20. Reset Timing.......................................................................................................................................................53

Figure 21. Recommended Reset Circuit..............................................................................................................................54

Figure 22. Recommended Reset Circuit for Interfacing with CPU/FPGA Reset Output .....................................................54

Figure 23. Reference Circuits for LED Strapping Pins.........................................................................................................55

Micrel, Inc. KSZ8041TL/FTL

April 2007 7 M9999-042707-1.1

List of Tables

Table 1. MII Management Frame Format............................................................................................................................20

Table 2. MII Signal Definition...............................................................................................................................................21

Table 3. RMII Signal Description..........................................................................................................................................23

Table 4. SMII Signal Description..........................................................................................................................................24

Table 5. SMII TX Bit Description..........................................................................................................................................25

Table 6. SMII TXD[0:7] Encoding Table ..............................................................................................................................25

Table 7. SMII RX Bit Description..........................................................................................................................................26

Table 8. SMII RXD[0:7] Encoding Table..............................................................................................................................26

Table 9. MDI/MDI-X Pin Definition.......................................................................................................................................27

Table 10. KSZ8041TL/FTL Power Pin Description..............................................................................................................31

Table 11. Copper and Fiber Mode Selection.......................................................................................................................32

Table 12. MII Signal Connection for MII Back-to-Back Mode..............................................................................................33

Table 13. RMII Signal Connection for RMII Back-to-Back Mode.........................................................................................34

Table 14. MII SQE Timing (10Base-T) Parameters.............................................................................................................45

Table 15. MII Transmit Timing (10Base-T) Parameters ......................................................................................................46

Table 16. MII Receive Timing (10Base-T) Parameters .......................................................................................................47

Table 17. MII Transmit Timing (100Base-TX) Parameters..................................................................................................48

Table 18. MII Receive Timing (100Base-TX) Parameters...................................................................................................49

Table 19. RMII Timing Parameters......................................................................................................................................50

Table 20. Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters...............................................................................51

Table 21. MDC/MDIO Timing Parameters...........................................................................................................................52

Table 22. Reset Timing Parameters ....................................................................................................................................53

Table 23. Transformer Selection Criteria.............................................................................................................................56

Table 24. Qualified Single Port Magnetics...........................................................................................................................56

Table 25. Typical Reference Crystal Characteristics...........................................................................................................56

Micrel, Inc. KSZ8041TL/FTL

April 2007 8 M9999-042707-1.1

Pin Configur ation

TXC

RST#

INTRP

REXT

GND

RXER / RX_ER /

ISO

GND

VDD_1.8

GND

VDDA_3.3

TXD1 / TXD[1] /

SYNC

TXD0 / TXD[0] /

TXEN /

TX_EN

LED1 /

SPEED

LED0 /

NWAYEN

CRS /

CONFIG1

13 14 16 17

4142434445464748

RX+

TX-

RX-

GND

TXD3

TXD2

GND

COL /

CONFIG0

37383940

RXC

VDDIO_3.3

RXDV / CRSDV /

CONFIG2

RXD2 /

PHYAD1

RXD1 / RXD[1] /

PHYAD2

RXD0 / RXD[0] / RX

DUPLEX

21 22 23

MDIO

MDC

RXD3 /

PHYAD0

18 19 20

XI / REFCLK /

CLOCK

TX+

VDDA_1.8

V1.8_OUT

VDDA_3.3

KSZ8041TL

48-Pin TQFP

Micrel, Inc. KSZ8041TL/FTL

April 2007 9 M9999-042707-1.1

TXC

RST#

INTRP

REXT

GND

RXER / RX_ER /

ISO

GND

VDD_1.8

GND

VDDA_3.3

FXSD /

FXEN

TXD1 / TXD[1] /

SYNC

TXD0 / TXD[0] /

TXEN /

TX_EN

LED1 /

SPEED / no FEF

LED0 /

NWAYEN

CRS /

CONFIG1

13 14 16 17

4142434445464748

RX+

TX-

RX-

GND

TXD3

TXD2

GND

COL /

CONFIG0

37383940

RXC

VDDIO_3.3

RXDV / CRSDV /

CONFIG2

RXD2 /

PHYAD1

RXD1 / RXD[1] /

PHYAD2

RXD0 / RXD[0] / RX

DUPLEX

21 22 23

MDIO

MDC

RXD3 /

PHYAD0

18 19 20

XI / REFCLK /

CLOCK

TX+

VDDA_1.8

V1.8_OUT

VDDA_3.3

KSZ8041FTL

48-Pin TQFP

Micrel, Inc. KSZ8041TL/FTL

April 2007 10 M9999-042707-1.1

Pin Description

Pin Number Pin Name Type(1) Pin Function

1 GND Gnd Ground

2 GND Gnd Ground

3 GND Gnd Ground

4 VDDA_1.8 P 1.8V analog VDD

5 VDDA_1.8 P 1.8V analog VDD

6 V1.8_OUT P 1.8V output voltage from chip

7 VDDA_3.3 P 3.3V analog VDD

8 VDDA_3.3 P 3.3V analog VDD

9 RX- I/O Physical receive or transmit signal (- differential)

10 RX+ I/O Physical receive or transmit signal (+ differential)

11 TX- I/O Physical transmit or receive signal (- differential)

12 TX+ I/O Physical transmit or receive signal (+ differential)

13 GND Gnd Ground

14 XO O Crystal feedback

This pin is used only in MII mode when a 25 MHz crystal is used.

This pin is a no connect if oscillator or external clock source is used, or if RMII

mode or SMII mode is selected.

15 XI /

REFCLK /

CLOCK

I Crystal / Oscillator / External Clock Input

MII Mode: 25MHz +/-50ppm (crystal, oscillator, or external clock)

RMII Mode: 50MHz +/-50ppm (oscillator, or external clock only)

SMII Mode: 125MHz +/-100ppm (oscillator, or external clock only)

16 REXT I/O Set physical transmit output current

Connect a 6.49KΩ resistor in parallel with a 100pF capacitor to ground on this

pin. See KSZ8041TL-FTL reference schematics.

17 GND Gnd Ground

18 MDIO I/O Management Interface (MII) Data I/O

This pin requires an external 4.7KΩ pull-up resistor.

19 MDC I Management Interface (MII) Clock Input

This pin is synchronous to the MDIO data interface.

20 RXD3 /

PHYAD0 Ipu/O MII Mode: Receive Data Output[3](2) /

Config Mode: The pull-up/pull-down value is latched as PHYADDR[0] during

power-up / reset. See “Strapping Options” section for details.

21 RXD2 /

PHYAD1 Ipd/O MII Mode: Receive Data Output[2](2) /

Config Mode: The pull-up/pull-down value is latched as PHYADDR[1] during

power-up / reset. See “Strapping Options” section for details.

22 RXD1 /

RXD[1] /

PHYAD2

Ipd/O MII Mode: Receive Data Output[1](2) /

RMII Mode: Receive Data Output[1](3) /

Config Mode: The pull-up/pull-down value is latched as PHYADDR[2] during

power-up / reset. See “Strapping Options” section for details.

Micrel, Inc. KSZ8041TL/FTL

April 2007 11 M9999-042707-1.1

Pin Number Pin Name Type(1) Pin Function

23 RXD0 /

RXD[0] /

DUPLEX

Ipu/O MII Mode: Receive Data Output[0](2) /

RMII Mode: Receive Data Output[0](3) /

SMII Mode: Receive Data and Control(4) /

Config Mode: Latched as DUPLEX (register 0h, bit 8) during po wer-up /

reset. See “Strapping Options” section for details.

24 GND Gnd Ground

25 VDDIO_3.3 P 3.3V digital VDD

26 VDDIO_3.3 P 3.3V digital VDD

27 RXDV /

CRSDV /

CONFIG2

Ipd/O MII Mode: Receive Data Valid Output /

RMII Mode: Carrier Sense/Receive Data Valid Output /

Config Mode: The pull-up/pull-down value is latched as CONFIG2 during

power-up / reset. See “Strapping Options” section for details.

28 RXC O MII Mode: Receive Clock Output

29 RXER /

RX_ER /

ISO

Ipd/O MII Mode: Receive Error Output /

RMII Mode: Receive Error Output /

Config Mode: The pull-up/pull-down value is latched as ISOLATE during

power-up / reset. See “Strapping Options” section for details.

30 GND Gnd Ground

31 VDD_1.8 P 1.8V digital VDD

32 INTRP Opu Interrupt Output: Programmable Interrupt Output

interrupt conditions and readi ng the interrupt status. Register 1Fh bit 9 sets the

interrupt output to active low (default) or active high.

33 TXC I/O MII Mode: Transmit Clock Output

MII Back-to Back Mode: Transmit Clock Input

34 TXEN /

TX_EN I MII Mode: Transmit Enable Input /

RMII Mode: Transmit Enable Input

35 TXD0 /

TXD[0] /

I MII Mode: Transmit Data Input[0](5) /

RMII Mode: Transmit Data Input[0](6) /

SMII Mode: Transmit Data and Control(7)

36 TXD1 /

TXD[1] /

SYNC

I MII Mode: Transmit Data Input[1](5) /

RMII Mode: Transmit Data Input[1](6) /

SMII Mode: SYNC Clock Input

37 GND Gnd Ground

38 TXD2 I

MII Mode: Transmit Data Input[2](5) /

39 TXD3 I

MII Mode: Transmit Data Input[3](5) /

40 COL /

CONFIG0 Ipd/O MII Mode: Collision Detect Output /

Config Mode: The pull-up/pull-down value is latched as CONFIG0 during

power-up / reset. See “Strapping Options” section for details.

41 CRS /

CONFIG1 Ipd/O MII Mode: Carrier Sense Output /

Config Mode: The pull-up/pull-down value is latched as CONFIG1 during

power-up / reset. See “Strapping Options” section for details.

Micrel, Inc. KSZ8041TL/FTL

April 2007 12 M9999-042707-1.1

Pin Number Pin Name Type(1) Pin Function

(KSZ8041TL) LED0 /

NWAYEN Ipu/O LED Output: Programmable LED0 Output /

Config Mode: Latche d as Auto-Negotiation Enable (register 0h, bit 12)

during power-up / reset. See “Strapping Options” section for

details.

The LED0 pin is programmable via register 1Eh bits [15:14], and is define d as

follows.

LED mode = [00]

Link/Activity Pin State LED Definition

No Link H OFF

Link L ON

Activity Toggle Blinking

LED mode = [01]

Link Pin State LED Definition

No Link H OFF

Link L ON

LED mode = [10]

Reserved

LED mode = [11]

Reserved

(KSZ8041FTL) LED0 /

NWAYEN Ipu/O LED Output: Programmable LED0 Output /

Config Mode: If copper mode (F XEN=0), latched as Auto-Negotiation

Enable (register 0h, bit 12) during power-up / reset.

If fiber mode (FXEN=1), this pin configuration is always

strapped to disable Auto-Neg otiation.

See “Strapping Options” section for details.

The LED0 pin is programmable via register 1Eh bits [15:14], and is define d as

follows.

LED mode = [00]

Link/Activity Pin State LED Definition

No Link H OFF

Link L ON

Activity Toggle Blinking

LED mode = [01]

Link Pin State LED Definition

No Link H OFF

Link L ON

LED mode = [10]

Reserved

LED mode = [11]

Reserved

Micrel, Inc. KSZ8041TL/FTL

April 2007 13 M9999-042707-1.1

Pin Number Pin Name Type(1) Pin Function

(KSZ8041TL) LED1 /

SPEED Ipu/O LED Output: Programmable LED1 Output /

Config Mode: Latche d as SPEED (register 0h, bit 13) during power-up /

reset. See “Strapping Options” section for details.

The LED1 pin is programmable via register 1Eh bits [15:14], and is define d as

follows.

LED mode = [00]

Speed Pin State LED Definition

10BT H OFF

100BT L ON

LED mode = [01]

Activity Pin State LED Definition

No Activity H OFF

Activity Toggle Blinking

LED mode = [10]

Reserved

LED mode = [11]

Reserved

(KSZ8041FTL) LED1 /

SPEED /

no FEF

Ipu/O LED Output: Programmable LED1 Output /

Config Mode: If copper mode (FXEN=0), latched as SPEED (register 0h, bit

13) during power-up / reset.

If fiber mode (FXEN=1), latched as no FEF (no Far-End Fault)

during power-up / reset.

See “Strapping Options” section for details.

The LED1 pin is programmable via register 1Eh bits [15:14], and is define d as

follows.

LED mode = [00]

Speed Pin State LED Definition

10BT H OFF

100BT L ON

LED mode = [01]

Activity Pin State LED Definition

No Activity H OFF

Activity Toggle Blinking

LED mode = [10]

Reserved

LED mode = [11]

Reserved

44 NC - No connect

45 NC - No connect

46 NC - No connect

Micrel, Inc. KSZ8041TL/FTL

April 2007 14 M9999-042707-1.1

Pin Number Pin Name Type(1) Pin Function

47 RST# I Chip Reset (active low)

(KSZ8041TL)

NC - No connect

(KSZ8041FTL) FXSD /

FXEN Ipd FXSD: Signal Detect for 100Base-FX fiber mode

FXEN: Fiber Enable for 100Base-FX fiber mode

If FXEN=0, fiber mode is disabled. PHY is in copper mode. The default is “0”.

See “100Base-FX Operation” section for details.

Notes:

1. P = Power supply.

Gnd = Ground.

I = Input.

O = Output.

I/O = Bi-directional.

Ipd = Input with internal pull-down (40K +/-30%).

Ipu = Input with internal pull-up (40K +/-30%).

Opu = Output with internal pull-up (40K +/-30%).

Ipu/O = Input with internal pull-up (40K +/-30%) during power-up/reset; output pin otherwise.

Ipd/O = Input with internal pull-down (40K +/-30%) during power-up/reset; output pin otherwise.

2. MII Rx Mode: The RXD[3..0] bits are synchronous with RXCLK. When RXDV is asserted, RXD[3..0] presents valid data to MAC through the MII.

RXD[3..0] is invalid when RXDV is de-asserted.

3. RMII Rx Mode: The RXD[1:0] bits are synchronous with REF_CLK. For each clock period in which CRS_DV is asserted, two bits of recovered

data are sent from the PHY.

4. SMII Rx Mode: Receive data and control information are sent in 10 bit segments. In 100MBit mode, each segment represents a new byte of

data. In 10MBit mode, each segment is repeated ten times; therefore, every ten segments represent a new byte of data. The MAC can sample

any one of every 10 segments in 10MBit mode.

5. MII Tx Mode: The TXD[3..0] bits are synchronous with TXCLK. When TXEN is asserted, TXD[3..0] presents valid data from the MAC through

the MII. TXD[3..0] has no effect when TXEN is de-asserted.

6. RMII Tx Mode: The TXD[1:0] bits are synchronous with REF_CLK. For each clock period in which TX_EN is asserted, two bits of data are

received by the PHY from the MAC.

7. SMII Tx Mode: Transmit data and control information are received in 10 bit segments. In 100MBit mode, each segment represents a new byte

of data. In 10MBit mode, each segment is repeated ten times; therefore, ever y ten segments represent a new byte of data. The P H Y can

sample any one of every 10 segments in 10MBit mode.

Micrel, Inc. KSZ8041TL/FTL

April 2007 15 M9999-042707-1.1

Strapping Options

Pin Number Pin Name Type(1) Pin Function

PHYAD2

PHYAD1

PHYAD0

Ipd/O

Ipu/O

The PHY Address is latched at power-up / reset and is con figurable to any value from

1 to 7.

The default PHY Address is 00001.

PHY Address bits [4:3] are always set to ‘00’.

CONFIG2

CONFIG1

CONFIG0

Ipd/O

The CONFIG[2:0] strap-in pins are latched at power-up / reset and are defined as

follows:

CONFIG[2:0] Mode

000 MII (default)

001 RMII

010 SMII

011 Reserved – not used

100 PCS Loopback

101 RMII back-to-back

110 MII back-to-back

111 Reserved – not used

29 ISO Ipd/O ISOLATE mode

Pull-up = Enable

Pull-down (default) = Disable

During power-up / reset, this pin value is latched into register 0h bit 10.

(KSZ8041TL) SPEED Ipu/O SPEED mode

Pull-up (default) = 100Mbps

Pull-down = 10Mbps

During power-up / reset, this pin value is latched i nto register 0h bit 13 as the Speed

Select, and also is latched into register 4h (Auto-Negotiation Advertisement) as the

Speed capability support.

(KSZ8041FTL) SPEED /

no FEF

Ipu/O If copper mode (FXEN= 0), pin strap-in is SPEED mode.

Pull-up (default) = 100Mbps

Pull-down = 10Mbps

During power-up / reset, this pin value is latched i nto register 0h bit 13 as the Speed

Select, and also is latched into register 4h (Auto-Negotiation Advertisement) as the

Speed capability support.

If fiber mode (FXEN=1), pin strap-in is no FEF.

Pull-up (default) = Enable Far-End Fault

Pull-down = Disable Far-End Fault

This pin value is latched during power-up / reset.

Micrel, Inc. KSZ8041TL/FTL

April 2007 16 M9999-042707-1.1

Pin Number Pin Name Type(1) Pin Function

23 DUPLEX Ipu/O DUPLEX mode

Pull-up (default) = Half Duplex

Pull-down = Full Duplex

During power-up / reset, this pin value is latched i nto register 0h bit 8 as the Duplex

Mode.

(KSZ8041TL) NWAYEN Ipu/O Nway Auto-Negotiation Enable

Pull-up (default) = Enable Auto-Negotiation

Pull-down = Disable Auto-Negotiati on

During power-up / reset, this pin value is latched into register 0h bit 12.

(KSZ8041FTL) NWAYEN Ipu/O If copper mode (FXEN=0), pin strap-in is Nway Auto-Negotiation Enable.

Pull-up (default) = Enable Auto-Negotiation

Pull-down = Disable Auto-Negotiati on

During power-up / reset, this pin value is latched into register 0h bit 12.

If fiber mode (FXEN=1), this pin configuration is always strapped to disable Auto-

Negotiation.

Note:

1. Ipu/O = Input with internal pull-up (40K +/-30%) during power-up/reset; output pin otherwise.

Ipd/O = Input with internal pull-down (40K +/-30%) during power-up/reset; output pin otherwise.

Pin strap-ins are latched during power-up or reset. In some systems, the MAC receive input pins may drive high during

power-up or reset, and consequently cause the PHY strap-in pins on the MII/RMII/SMII signals to be latched high. In this

case, it is recommended to add 1K pull-downs on these PHY strap-in pins to ensure the PHY does not strap-in to

ISOLATE or PCS Loopback mode, or is not co nfigured with an incorrect PHY Address.

Micrel, Inc. KSZ8041TL/FTL

April 2007 17 M9999-042707-1.1

Functional Description

The KSZ8041TL is a single 3.3V supply Fast Ethernet transceiver. It is fully compliant with the IEEE 802.3u Specification.

On the media side, the KSZ8041TL supports 10Base-T and 100Base-TX with HP auto MDI/MDI-X for reliable detection of

and correction for straight-through and crossover cables.

The KSZ8041TL offers a choice of MII, RMII, or SMII data interface connection to a MAC processor. The MII management

bus option gives the MAC processor complete access to the KSZ8041TL control and status registers. Additionally, an

interrupt pin eliminates the need for the processor to poll for PHY status change.

Physical signal transmission and reception are enhanced through the use of patented analog circuitries that make the

design more efficient and allow for lower power consumption and smaller chip die size.

The KSZ8041FTL has all the identical rich featu res of the KSZ8041TL plus 100Base -FX fiber support.

100Base-TX Transmit

The 100Base-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI

conversion, and MLT3 encoding and transmission.

The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit

stream. The data and control stream is then converted into 4B/5B coding, followed by a scrambler. The serialized data is

further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output.

The output current is set by an external 6.49 KΩ 1% resistor for the 1:1 transformer ratio. It has typical rise/fall times of 4

ns and complies with the ANSI TP-PMD standard regarding amplitude balance, overshoot and timing jitter. The wave-

shaped 10Base-T output drivers are al so incorporated into the 100Base-TX drivers.

100Base-TX Receiv e

The 100Base-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data and

clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion.

The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted pair

cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer must adjust its

characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based upon

comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for optimization.

This is an ongoing process and self-adjusts against environmental changes such as temperature variations.

Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used to

compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion circuit

converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.

The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then used

to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B

decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the MAC.

PLL Clock Synthesizer

The KSZ8041TL/FTL generates 125 MΗz, 25 MΗz and 20 MΗz clocks for system timing. Internal clocks are generated

from an external 25 MHz crystal or oscillator. In RMII mode, these internal clocks are generated from an external 50 MHz

oscillator or system clock.

Scrambler/De-scrambler (100Base-TX only )

The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline wander.

10Base-T Transmit

The 10Base-T drivers are incorporated with the 100Base-TX drivers to allow for transmission using the same magnetic.

The drivers also perform internal wave-shaping and pre-emphasize, and output 10Base-T signals with a typical amplitude

of 2.5V peak. The 10Base-T signals have harmonic contents that are at least 27dB below the fundamental frequency

when driven by an all-ones Manchester-encoded signal.

Micrel, Inc. KSZ8041TL/FTL

April 2007 18 M9999-042707-1.1

10Base-T Receive

On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and

a PLL performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data.

A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths to prevent noise at the RX+ and

RX- inputs from falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming

signal and the KSZ8041TL/FTL decodes a data frame. The receive clock is kept active during idle periods in between

data reception.

SQE and Jabber Function (10Bas e-T only)

In 10Base-T operation, a short pulse is put out on the COL pin after each frame is transmitted. This SQE Test is required

as a test of the 10Base-T transmit/receive path. If transmit enable (TXEN) is high for more than 20 ms (jabbering), the

10Base-T transmitter is disabled and COL is asserted high. If TXEN is then driven low for more than 250 ms, the 10Base-

T transmitter is re-enabled and COL is de-asserted (returns to low).

Auto-Negotiation

The KSZ8041TL/FTL conforms to the auto-negotiation protocol, defined in Clause 28 of the IEEE 802.3u specification.

Auto-negotiation is enabled by either hardware pin strapping (pin 30) or software (regi ster 0h bit 12).

Auto-negotiation allows unshielded twisted pair (UTP) link partners to select the highest common mode of operation. Link

partners advertise their capabilities to each other, and then compare their own capabilities with those they received from

their link partners. The highest speed and duplex setting that is common to the two link partners is selected as the mode

of operation.

The following list shows the spe ed and duplex operation mode from highe st to lowest.

• Priority 1: 100Base-TX, full-duplex

• Priority 2: 100Base-TX, half-duplex

• Priority 3: 10Base-T, full-duplex

• Priority 4: 10Base-T, half-duplex

If auto-negotiation is not supported or the KSZ8041TL/FTL link partner is forced to bypass auto-negotiation, the

KSZ8041TL/FTL sets its operating mode by observing the signal at its receiver. This is known as parallel detection, and

allows the KSZ8041TL/FTL to establish link by listening for a fixed signal protocol in the absence of auto-negotiation

advertisement protocol.

The auto-negotiation link up proce ss is shown in the following flow chart.

Micrel, Inc. KSZ8041TL/FTL

April 2007 19 M9999-042707-1.1

Start Auto Negotiat ion

Force Link Setting

Listen for 10BASE-T

Link Pulses

Listen for 100BASE-TX

Idles

ttempt Auto

Negotiation

Link Mode Set

Bypass Auto Negotiation

and Set Link Mode

Link Mode Set ?

Parallel

Operation

Join

Flow

Yes

Figure 1. Auto-Negotiation Flow Chart

Micrel, Inc. KSZ8041TL/FTL

April 2007 20 M9999-042707-1.1

MII Management (MIIM) Interface

The KSZ8041TL/FTL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /

Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the

KSZ8041TL/FTL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY

settings. Further detail on the MIIM interface can be found in Clause 22.2.4.5 of the IEEE 802.3u Specification.

The MIIM interface consists of the following:

• A physical connection that incorporates the clock line (MDC) and the data line (MDIO).

• A specific protocol that operates across the aforementioned physical connection that allows an external controller

to communicate with one or more KSZ8041TL/FTL devices. Each KSZ8041TL/FTL device is assigned a PHY

address between 1 and 7 by the PHYAD[2:0] strappin g pins.

• An internal addressable set of thirteen 16-bit MDIO registers. Register [0:6] are required, and their functions are

defined by the IEEE 802.3u Specification. The additional registers are provided for expanded functionality.

The KSZ8041TL/FTL supports MIIM in MII mode, RMII mode and SMII mode.

The following table shows the MII Manag ement frame format for the KSZ8041TL/FTL.

Preamble

Start of

Frame Read/Write

OP Code

PHY

Address

Bits [4:0]

REG

Address

Bits [4:0]

TA Data

Bits [15:0]

Idle

Read 32 1’s 01 10 00AAA RRRRR Z0 DDDDDDDD_DDDDDDDD Z

Write 32 1’s 01 01 00AAA RRRRR 10 DDDDDDDD_DDDDDDDD Z

Table 1. MII Management Frame Format

Interrupt (INTRP)

INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status

update in the KSZ8041TL/FTL PHY register. Bits[15:8] of register 1Bh are the interrupt control bits, and are used to

enable and disable the conditions for asserting the INTRP signal. Bits[7:0] of register 1Bh are the interrupt status bits, and

are used to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register

1Bh.

Bit 9 of register 1Fh sets the interrupt level to active high or active low.

MII Data Interface

The Media Independent Interface (MII) is specified in Clause 22 of the IEEE 802.3u Specification. It provides a common

interface between physica l layer and MAC layer devices, and has the following key characteristics:

• Supports 10Mbps and 100Mbps data rates.

• Uses a 25 MHz reference clo ck, sourced by the PHY.

• Provides independent 4-bit wide (nibble) transmit and receive data paths.

• Contains two distinct groups of signals: one for transmission an d the other for reception.

By default, the KSZ8041TL/FTL is configured in MII mode after it is power-up or reset with the following:

• A 25 MHz crystal connected to XI, XO (pins 15, 14), or an external 25MHz clock source (oscillator) connected to

XI.

• CONFIG[2:0] (pins 27, 41, 40) set to ‘000’ (default setting).

Micrel, Inc. KSZ8041TL/FTL

April 2007 21 M9999-042707-1.1

MII Signal Definition

The following table describes the MII signals. Refer to Clause 22 of the IEEE 802.3u Specification for detailed information.

MII

Signal Name

Direction

(with respect to PHY,

KSZ8041TL/FTL signal)

Direction

(with respect to MAC) Description

TXC Output Input Transmit Clock

(2.5 MHz for 10Mbps; 25 MHz for 100Mbps)

TXEN Input Output Transmit Enable

TXD[3:0] Input Output Transmit Data [3:0]

RXC Output Input Receive Clock

(2.5 MHz for 10Mbps; 25 MHz for 100Mbps)

RXDV Output Input Receive Data Valid

RXD[3:0] Output Input Receive Data [3:0]

RXER Output Input, or (not required) Receive Error

CRS Output Input Carrier Sense

COL Output Input Collision Detection

Table 2. MII Signal Definition

Transmit Clock (TXC)

TXC is sourced by the PHY. It is a continuous clock that provide s the timing refe rence for TXEN and TXD[3:0].

TXC is 2.5MHz for 10Mbps ope ration and 25MHz for 100Mbps operation.

Transmit Enable (TXEN)

TXEN indicates the MAC is presenting nibbles on TXD[3:0] for transmission. It is asserted synchronously with the first

nibble of the preamble and remains asserted while all nibbles to be transmitted are presented on the MII, and is negated

prior to the first TXC following the final nibble of a fram e.

TXEN transitions synchronously with respect to TXC.

Transmit Data [3:0] (TXD[3:0])

TXD[3:0] transitions synchronously with respect to TXC. When TXEN is asserted, TXD[3:0] are accepted for transmission

by the PHY. TXD[3:0] is ”00” to indicate idle when TXEN is de-asserted. Values other than “00” on TXD[3:0] while TXEN

is de-asserted are ignored by the PHY.

Receive Clock (RXC)

RXC provides the timing reference for RXDV, RXD[3:0], and RXER.

• In 10Mbps mode, RXC is recovered from the line while carrier is active. RXC is derived from the PHY’s reference

clock when the line is idle, or link is down.

• In 100Mbps mode, RXC is continuously recovered from the line. If link is down, RXC is derived from the PHY’s

reference clock.

RXC is 2.5MHz for 10Mbps operation and 25MHz for 100Mbp s operation.

Micrel, Inc. KSZ8041TL/FTL

April 2007 22 M9999-042707-1.1

Receive Data Valid (RXDV)

RXDV is driven by the PHY to indicate that the PHY is presenting recovered and decoded nib bles on RXD[3:0].

• In 10Mbps mode, RXDV is asserted with the first nibble of the SFD (Start of Frame Delimiter), “5D”, and remains

asserted until the end of the frame.

• In 100Mbps mode, RXDV is asserted from the first nibble of the preamble to the last nibble of the frame.

RXDV transitions synchronously with respect to RXC.

Receive Data [3:0] (RXD[3:0])

RXD[3:0] transitions synchronously with respect to RXC. For each clock period in which RXDV is asserted, RXD[3:0]

transfers a nibble of recov ered data from the PHY.

Receive Error (RXER)

RXER is asserted for one or more RXC periods to indicate that a Symbol Error (e.g. a coding error that a PHY is capable

of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the frame

presently being transferred from the PHY.

RXER transitions synchron ously with respect to RXC. While RXDV is de-asserted, RXER has no effect on the MAC.

Carrier Sense (CRS)

CRS is asserted and de-a sserted as follows:

• In 10Mbps mode, CRS assertion is based on the reception of valid preambles. CRS de-assertion is based on the

reception of an end-of-frame (EOF) marker.

• In 100Mbps mode, CRS is asserted when a start-of-stream delimiter, or /J/K symbol pair is detected. CRS is de-

asserted when an end-of-stream delimiter, or /T/R symbol pair is detected. Additionally, the PMA layer de-asserts

CRS if IDLE symbols are received without /T/R.

Collision (COL)

COL is asserted in half-duplex mode whenever the transmitter and receiver are simultaneously active on the line. This is

used to inform the MAC that a collision has occurred during its transmission to the PHY.

COL transitions asynchronously with respect to TXC and RXC.

Reduced MII (RMII) Data Interface

The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). It provides

a common interface between physical layer and MAC layer devices, and has the following key characteristics:

• Supports 10Mbps and 100Mbps data rates.

• Uses a single 50 MHz reference clock provided by the MAC or the system board.

• Provides independent 2-bit wide (di-bit) transmit and receive data paths.

• Contains two distinct groups of signals: one for transmission an d the other for reception.

The KSZ8041TL/FTL is configured in RMII mode after it is power-u p or reset with the following:

• A 50 MHz reference clock connected to REFCLK (pin 15).

• CONFIG[2:0] (pins 27, 41, 40) set to ‘001’.

In RMII mode, unused MII signals, TXD[3:2] (pins 3 9, 38), are tied to ground.

Micrel, Inc. KSZ8041TL/FTL

April 2007 23 M9999-042707-1.1

RMII Signal Definition

The following table describes the RMII signals. Refer to RMII Specification for detailed information.

RMII

Signal Name

Direction

(with respect to PHY,

KSZ8041TL/FTL signal)

Direction

(with respect to MAC) Description

REF_CLK Input Input, or Output Synchronous 50 MHz clock reference for

receive, transmit and control interface

TX_EN Input Output Transmit Enable

TXD[1:0] Input Output Transmit Data [1:0]

CRS_DV Output Input Carrier Sense/Receive Data Valid

RXD[1:0] Output Input Receive Data [1:0]

RX_ER Output Input, or (not requir ed) Receive Error

Table 3. RMII Signal Description

Reference Clock (REF_C LK)

REF_CLK is sourced by the MAC or system board. It is a continuous 50 MHz clock that provides the timing reference for

TX_EN, TXD[1:0], CRS_DV, RXD[1:0], and RX_ER.

Transmit Enable (TX_EN)

TX_EN indicates that the MAC is presenting di-bits on TXD[1:0] for transmission. It is asserted synchronously with the first

nibble of the preamble and remains asserted while all di-bits to be transmitted are presented on the RMII, and is negated

prior to the first REF_CLK following the final di-bit of a frame.

TX_EN transitions synchronously with respect to REF_CLK.

Transmit Data [1:0] (TXD[1:0])

TXD[1:0] transitions synchronously with respect to REF_CLK. When TX_EN is asserted, TXD[1:0] are accepted for

transmission by the PHY. TXD[1:0] is ”00” to indicate idle when TX_EN is de-asserted. Values other than “00” on TXD[1:0]

while TX_EN is de-asserted are ignored by the PHY.

Carrier Sense/Receive Data Valid (CRS_DV)

CRS_DV is asserted by the PHY when the receive medium is non-idle. It is asserted asynchronously on detection of

carrier. This is when squelch is passed in 10Mbps mode, and when 2 non-contiguous zeroes in 10 bits are detected in

100Mbps mode. Loss of carrier results in the de-assertion of CRS _DV.

So long as carrier detection criteria are met, CRS_DV remains asserted continuously from the first recovered di-bit of the

frame through the final recovered di-bit, and it is negated prior to the first REF_CLK that follows the final di-bit. The data

on RXD[1:0] is considered valid once CRS_DV is asserted. However, since the assertion of CRS_DV is asynchronous

relative to REF_CLK, the data on RXD[1:0] is "00" until proper receive signal decoding takes p lace.

Receive Data [1:0] (RXD[1:0])

RXD[1:0] transitions synchronously to REF_CLK. For each clock period in which CRS_DV is asserted, RXD[1:0] transfers

two bits of recovered data from the PHY. RXD[1:0] is "00" to indicate idle when CRS_DV is de-asserted. Values other

than “00” on RXD[1:0] while CRS_DV is de-asserted are ignored b y the MAC.

Receive Error (RX_ER)

RX_ER is asserted for one or more REF_CLK periods to indicate that a Symbol Error (e.g. a coding error that a PHY is

capable of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the

frame presently being transferred from the PHY.

RX_ER transitions synchronously with respect to REF_CLK. While CRS_DV is de-asserted, RX_ER has no effect on the

MAC.

Micrel, Inc. KSZ8041TL/FTL

April 2007 24 M9999-042707-1.1

Collision Detection

The MAC regenerates the COL signal of the MII from TX_EN and CRS_DV.

Serial MII (SMII) Data Interface

The Serial Media Independent Interface (SMII) is the lowest pin count Media Independent Interface (MII). It provides a

common interface between physical layer and MAC layer devices, and has the following key characteristics:

• Supports 10Mbps and 100Mbps data rates.

• Uses 125 MHz reference clock provided by the MAC or the system board.

• Uses 12.5 MHz sync pulse provided by the MAC.

• Provides independent single-bit wide transmit and receive data paths for data and control information.

The KSZ8041TL/FTL is configured in SMII mode after it is power-u p or reset with the following:

• A 125 MHz reference clock connecte d to CLOCK (pin 15).

• A 12.5 MHz sync pulse connected to SYNC (pin 36).

• CONFIG[2:0] (pins 27, 41, 40) set to ‘010’.

In SMII mode, unused MII signals, TXD[3:2] (pins 39, 38), are tied to grou nd.

SMII Signal Definition

The following table describes the SMII signals. Refer to SMII Specification for detailed information.

SMII

Signal Name

Direction

(with respect to PHY,

KSZ8041TL/FTL signal)

Direction

(with respect to MAC) Description

CLOCK Input Input, or Output 125 MHz clock reference for receive and

transmit data and control

SYNC Input Output 12.5 MHz sync pulse from MAC

TX Input Output Transmit Data and Control

RX Output Input Receiv e Data and Control

Table 4. SMII Signal Description

Clock Reference (CLOCK)

CLOCK is sourced by the MAC or system board. It is a continuous 125 MHz clock that provides the timing reference for

SYNC, TX, and RX.

Sync Pulse (SYNC)

SYNC is a 12.5 MHz synchronized pulse derived from CLOCK by the MAC. It is used to indicate the segment boundary

for each transmit data/control segment, or receive data/ control segment. Each segment is comprised of ten bits.

SYNC is generated continuou sly by the MAC at every ten cycles of CLOCK.

Transmit Data and Control (TX)

TX provides transmit data and control information from MAC-to -PHY in 10-bit segments.

• In 10Mbps mode, each segment is repeated ten times. Therefore, every ten segments represent a new byte of

data. The PHY can sample any one of every ten segments.

• In 100Mbps mode, each segment represents a new byte of data.

Micrel, Inc. KSZ8041TL/FTL

April 2007 25 M9999-042707-1.1

The following figure and table shows the transmit data/control format for each segment:

TX_ER TX_EN TXD0 TXD1 TXD2 TXD3 TXD4 TXD5 TXD6 TXD7

CLOCK

SYNC

Figure 2. SMII Transmit Data/Control Segment

SMII TX Bit Description

TX_ER Transmit Error

TX_EN Transmit Enable

TXD[0:7] Encoded Data

See SMII TXD[0:7] Encoding Table (below)

Table 5. SMII TX Bit Description

TX_ER TX_EN TXD0 TXD1 TXD2 TXD3 TXD4 TXD5 TXD6 TXD7

X 0 Use to

force an

error in a

direct

MAC-to-

MAC

connection

Speed

0=10M

1=100M

Duplex

0=Half

1=Full

Link

0=Down

1=Up

Jabber

0=No

1=Yes

1 1 1

X 1 One Data Byte

Table 6. SMII TXD[0:7] Encoding Table

Receive Data and Control (RX)

RX provides receive data and control information from PHY-to-MAC in 10-bit segments.

• In 10Mbps mode, each segment is repeated ten times. Therefore, every ten segments represent a new byte of

data. The MAC can sample any one of every ten segments.

• In 100Mbps mode, each segment represents a new byte of data.

Micrel, Inc. KSZ8041TL/FTL

April 2007 26 M9999-042707-1.1

The following figure and table shows the receive data/control format for each segment:

CRS RX_DV RXD0 RXD1 RXD2 RXD3 RXD4 RXD5 RXD6 RXD7

CLOCK

SYNC

Figure 3. SMII Receive Data/Cont rol Segment

SMII RX Bit Description

CRS Carrier Sense

RX_DV Receive Data Valid

RXD[0:7] Encoded Data

See SMII RXD[0:7] Encoding Table (below)

Table 7. SMII RX Bit Description

CRS RX_DV RXD0 RXD1 RXD2 RXD3 RXD4 RXD5 RXD6 RXD7

X 0 RX_ER

from

pervious

frame

Speed

0=10M

1=100M

Duplex

0=Half

1=Full

Link

0=Down

1=Up

Jabber

0=No

1=Yes

Upper

Nibble

0=Invalid

1=Valid

False

Carrier

Detected

X 1 One Data Byte

Table 8. SMII RXD[0:7] Encoding Table

Collision Detection

Collisions occur when CRS and TX_EN are simultaneously asserted. The MAC regenerates the MII collision signal from

CRS and TX_EN.

Micrel, Inc. KSZ8041TL/FTL

April 2007 27 M9999-042707-1.1

HP Auto MDI/MDI-X

HP Auto MDI/MDI-X configuration eliminates the confusion of whether to use a straight cable or a crossover cable

between the KSZ8041TL/FTL and its link partner. This feature allows the KSZ8041TL/FTL to use either type of cable to

connect with a link partner that is in either MDI or MDI-X mode. The auto-sense function detects transmit and receive

pairs from the link partner, and then assigns transmit and receive pairs of the KSZ8041TL/FTL accordingly.

HP Auto MDI/MDI-X is enabled by default. It is disabled by writing a one to register 1F bit 13. MDI and MDI-X mode is

selected by register 1F bit 14 if HP Auto MDI/MDI-X is disabled.

An isolation transformer with symmetrical transmit and receive data paths is recommended to support auto MDI/MDI-X.

The IEEE 802.3u Standard defines MDI and MDI-X as follow:

MDI MDI-X

RJ-45 Pin Signal RJ-45 Pin Signal

1 TD+ 1 RD+

2 TD- 2 RD-

3 RD+ 3 TD+

6 RD- 6 TD-

Table 9. MDI/MDI-X Pin Definition

Straight Cable

A straight cable connects a MDI device to a MDI-X device, or a MDI-X device to a MDI device. The following diagram

depicts a typical straight cable connection between a NIC card (MDI) and a switch, or hub (MDI-X).

Receive PairTransmit Pair

Receive Pair

Transmit Pair

Modular Connector

(RJ-45)

NIC

Straight

Cable

10/100 Ethernet

Media Dependent Interface 10/100 Ethernet

Media Dependent Interface

Modular Connector

(RJ-45)

HUB

(Repeater or Switch)

Figure 4. Typical Straight Cable Connection

Micrel, Inc. KSZ8041TL/FTL

April 2007 28 M9999-042707-1.1

Crossover Cable

A crossover cable connects a MDI device to another MDI device, or a MDI-X device to another MDI-X device. The

following diagram depict s a typical crossover cable connect ion between two switches or hu bs (two MDI-X devices).

Receive Pair Receive Pair

Transmit Pair

10/100 Ethernet

Media Dependent Interface 10/100 Ethernet

Media Dependent Interface

Modular Connector (RJ-45)

HUB

(Repeater or Switch)

Modular Connector (RJ-45)

HUB

(Repeater or Switch)

Crossover

Cable

Figure 5. Typical Crossover Cable Connection

Micrel, Inc. KSZ8041TL/FTL

April 2007 29 M9999-042707-1.1

LinkMD® Cable Diagnostics

The LinkMD® feature utilizes time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems,

such as open circuits, short circuits and im pedance mismatches.

LinkMD® works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs, and then analyzing

the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with

maximum distance of 200m and accuracy of +/-2m. Internal circuitry computes the TDR information and presents it in a

user-readable digital format.

Note: Cable diagnostics are only valid for copper connections and do not support fiber o ptic operation.

Access

LinkMD® is initiated by accessing register 1Dh, the LinkMD® Control/Status Register, in conjunction with register 1Fh, the

PHY Control 2 Register.

Usage

The following test procedure demon strates how to use LinkMD® for cable diagn ostic:

1. Disable auto MDI/MDI-X by writing a ‘1’ to register 1Fh bit 13 to enable manual control over the differential pair

used to transmit the LinkMD® pulse.

2. Select the differential pair to transmit the LinkMD® pulse with register 1Fh bit 14.

3. Start cable diagnostic test by writing a ‘1’ to register 1Dh bit 15. This enable bit is self-clea ring.

4. Wait (poll) for register 1Dh bit 15 to return a ‘0’, indicating cable dia gnostic test is completed.

5. Read cable diagnostic test results in register 1Dh bits [14:13]. The results are a s follows:

00 = normal condition (valid test)

01 = open condition detected in cable (valid test)

10 = short condition detected in cable (valid test)

11 = cable diagnostic test failed (invalid test)

The ‘11’ case, invalid test, occurs if the KSZ8041TL/FTL is unable to shut down the link partner. In this instance,

the test is not run, since it would be impossible for the KSZ8041TL/FTL to determine if the detected signal is a

reflection of the signal generated by the KSZ8041TL/FTL, or a si gnal from its link partner.

6. Get distance to fault by multiplying the decimal value in register 1Dh bits [8:0] by a constant of 0.4. The distance,

D (expressed in meters), to the cable fault is determined by the following formula:

D (distance to cable fault) = 0.4 x {decimal value of register 1Dh bits [8:0]}

The 0.4 constant can be calibrated for different cable types and cabling conditions, such a s cables with velocity of

propagation that varies significantly fro m the norm.

Power Management

The KSZ8041TL/FTL offers the following power man agement modes:

Power Saving Mode

This mode is used to reduce power consumption when the cable is unplugged. It is in effect when auto-negotiation mode

is enabled, cable is disconnected, and register 1Fh bit 10 is set to 1 (default setting). Under power saving mode, the

KSZ8041TL/FTL shuts down all transceiver blocks, except for energy detect and PLL circuits. Additionally, in MII mode,

the RXC clock output is disabled. RXC clock is enabled after the cable is conn ected and link is established.

Power saving mode is disabled by writing a zero to register 1Fh bit 10.

Power Down Mode

This mode is used to power down the entire KSZ8041TL/FTL device when it is not in use. Power down mode is enabled

by writing a one to register 0h bit 11. In the power down state, the KSZ8041TL/FTL disables all internal functions, except

for the MII management interface.

Micrel, Inc. KSZ8041TL/FTL

April 2007 30 M9999-042707-1.1

Reference Clock Connection Options

A crystal or clock source, such as an oscillator, is used to provide the reference clock for the KSZ8041TL/FTL. The

reference clock is 25 MHz for MII mode, 50 MHz for RMII mode, and 125 MHz for SMII mode. The following three figures

illustrate how to connect the referen ce clock to XI / REFCLK / CLOCK (pin 9) and XO (pin 8) of the KSZ8041TL/FTL.

25MHz OSC

+/-50ppm

22pF

25MHz XTAL

+/-50ppm

Figure 6. 25MHz Crystal / Oscillator Reference Clock for MII Mode

Figure 7. 50MHz Oscillator Reference Clock for RMII Mode

125MHz OSC

+/-100ppm

CLOCK

Figure 8. 125MHz Oscillator Reference Clock for SMII Mode

Micrel, Inc. KSZ8041TL/FTL

April 2007 31 M9999-042707-1.1

Reference Circuit for Power and Ground Connections

The KSZ8041TL/FTL is a single 3.3V supply device with a built-in 1.8V low noise regulator. The power and ground

connections are shown in the following figure and table.

Figure 9. KSZ8041TL/FTL Power and Ground Connections

Power Pin Pin Number Pin Type Description

V1.8_OUT 6 Output 1.8V supply output from KSZ8041TL/FTL

Decouple with 22uF and 0.1uF capacitors-to-ground.

VDD_1.8 31 Input Connect to V1.8_OUT (pin 6) thru ferrite bead.

Decouple with 0.1uF capacitor-to-ground.

VDDA_1.8 4, 5 Input Connect to V1.8_OUT (pin 6) thru ferrite bead.

Decouple with 0.1uF capacitor on each pin-to-ground.

VDDIO_3.3 25, 26 Input Connect to board’s 3.3V supply.

Decouple with 22uF and 0.1uF capacitors-to-ground.

VDDA_3.3 7, 8 Input Connect to board’s 3.3V supply thru ferrite bead.

Decouple with 22uF and 0.1uF capacitors-to-ground.

Table 10. KSZ8041TL/FTL Power Pin Description

Micrel, Inc. KSZ8041TL/FTL

April 2007 32 M9999-042707-1.1

100Base-FX Fiber Operation (KSZ8041FTL only)

100Base-FX fiber operation is similar to 100Base-TX copper operation with the differences being that the scrambler/de-

scrambler and MLT3 encoder/decoder are bypassed on transmission and reception. In addition, auto-negotiation is

bypassed, auto MDI/MDI-X is disabled, and speed is set to 100Mbps. The duplex can be set to either half or full. Usually,

it is set to full-duplex.

Fiber Signal Detect

In 100Base-FX operation, FXSD (fiber signal detect), input pin 48, is usually connected to the fiber transceiver SD (signal

detect) output pin. 100Base-FX mode is activated when the FXSD input pin is greater than 1V. When FXSD is between

1V and 1.8V, no fiber signal is detected and a Far-End Fault is generated. When FXSD is over 2.2V, the fiber signal is

detected.

100Base-FX mode and signal detection is summarized in the following table:

FXSD Input Voltage Mode

Less than 0.2V Copper mode

Greater than 1V, but less than 1.8V Fiber mode

No signal detected

Far-End Fault generated (if enabl ed)

Greater than 2.2V Fiber mode

Signal detected

Table 11. Copper and Fiber Mode Selection

To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD (signal detect)

output voltage swing to match the FXSD pin’s input voltage threshold.

Alternatively, the Far-End Fault feature can be disabled. In this case, the FXSD input pin is tied high to 3.3V to force

100Base-FX mode.

Far-End Fault

A Far-End Fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The

KSZ8041FTL detects a FEF when its FXSD input (pin 48) is between 1V and 1.8V. When a FEF is detected, the

KSZ8041FTL signals its fiber link partner that a FEF has occurred by transmitting a repetitive pattern of 84-ones and 1-

zero. This pattern is used to inform the fiber link partner that there is a faulty link on its transmit side.

By default, FEF is enabled. FEF is disabled by strapping “no FEF” (pin 43) low. See “Strapping Options” section for detail.

Micrel, Inc. KSZ8041TL/FTL

April 2007 33 M9999-042707-1.1

Back-to-Back Media Converter

A KSZ8041FTL and a KSZ8041TL can be connected back-to-back to provide a low cost media converter solution. In

back-to-back mode, media conversion is between 100Base-FX fiber and 100Base-TX copper. On the copper side, link up

at 10Base-T is not allowed, and is bloc ked during auto-negotiation.

Figure 10. KSZ8041FTL / KSZ8041TL Back-to-Back Media Converter

The KSZ8041FTL and KSZ8041TL support MII Back-to-Ba ck mode and RMII Back-to-Back mode for me dia conversion.

MII Back-to-Back Mode

The KSZ8041FTL and KSZ8041TL are configure d in MII Back-to-Back mode after it is power-up or reset with the following:

• CONFIG[2:0] (pins 27, 41, 40) set to ‘110’ for both KSZ8041FTL and KSZ8041T L.

• A common 25 MHz reference clock connected to XI (pin 15) of both KSZ8041FTL and KSZ8041TL.

• MII signals connected as shown in the following table between KSZ8041FTL in fiber mode and KSZ8041TL in

copper mode.

KSZ8041FTL in fiber mode KSZ8041TL in copper mode

Pin Name Pin Number Pin Type Pin Name Pin Number Pin Type

RXC 28 Output TXC 33 Input

RXDV 27 Output TXEN 34 Input

RXD3 20 Output TXD3 39 Input

RXD2 21 Output TXD2 38 Input

RXD1 22 Output TXD1 36 Input

RXD0 23 Output TXD0 35 Input

TXC 33 Input RXC 28 Output

TXEN 34 Input RXDV 27 Output

TXD3 39 Input RXD3 20 Output

TXD2 38 Input RXD2 21 Output

TXD1 36 Input RXD1 22 Output

TXD0 35 Input RXD0 23 Output

Table 12. MII Signal Connection for MII Back-to-Back Mode

Micrel, Inc. KSZ8041TL/FTL

April 2007 34 M9999-042707-1.1

RMII Back-to-Back M ode

The KSZ8041FTL and KSZ8041TL are configured in RMII Back-to-Back mode after it is power-up or reset with the

following:

• CONFIG[2:0] (pins 27, 41, 40) set to ‘101’ for both KSZ8041FTL and KSZ8041T L.

• A common 50 MHz reference clock connected to REFCLK (pin 15) of both KSZ8041FTL and KSZ8041TL.

• RMII signals connected as shown in the following table between KSZ8041FTL in fiber mode and KSZ8041TL in

copper mode.

KSZ8041FTL in fiber mode KSZ8041TL in copper mode

Pin Name Pin Number Pin Type Pin Name Pin Number Pin Type

CRSDV 27 Output TXEN 34 Input

RXD1 22 Output TXD1 36 Input

RXD0 23 Output TXD0 35 Input

TXEN 34 Input CRSDV 27 Output

TXD1 36 Input RXD1 22 Output

TXD0 35 Input RXD0 23 Output

Table 13. RMII Signal Connection for RMII Back-to-Back Mode

RMII Back-to-Back mode provides the option to disable and tri-state the transmitter on both copper and fiber sides if the

cable is disconnected on the copper side. On the copper side, RXD2 (pin 21) indicates if there is energy detected at the

receive inputs of the UTP port. RXD2 outputs a low if there is no energy detected (cable disconnected), and outputs a

high if the re is energy detec ted (cable connected) . The RXD2 output is connec ted thru an inverter to drive T XD2 (pin 38)

input high to disable and tri-state the transmitters for both copper and fiber sides.

The TXD3 and TXD2 pins should be pulled down with 1K resistors, and RXD3 and RXD2 pins should be left floating, if

they are not used.

Micrel, Inc. KSZ8041TL/FTL

April 2007 35 M9999-042707-1.1

0h Basic Control

1h Basic Status

2h PHY Identifier 1

3h PHY Identifier 2

4h Auto-Negotiation Advertisement

5h Auto-Negotiation Link Partner Ability

6h Auto-Negotiation Expansion

7h Auto-Negotiation Next Page

8h Link Partner Next Page Ability

9h – 14h Reserved

15h RXER Counter

16h – 1Ah Reserved

1Bh Interrupt Control/Status

1Ch Reserved

1Dh LinkMD® Control/Status

1Eh PHY Control 1

1Fh PHY Control 2

Address Name Description Mode(1) Default

0.15 Reset 1 = Software reset

0 = Normal operation

This bit is self-cleared after a ‘1’ is written to it.

RW/SC 0

0.14 Loop-back 1 = Loop-back mode

0 = Normal operation RW 0

0.13 Speed Select

(LSB) 1 = 100Mbps

0 = 10Mbps

This bit is ignored if auto-negotiation is enabled

(register 0.12 = 1).

RW Set by SPEED strapping pin.

See “Strapping Options” section

for details.

0.12 Auto-

Negotiation

Enable

1 = Enable auto-negotiation process

0 = Disable auto-negotiation process

If enabled, auto-negotiation result overrides

settings in register 0.13 and 0.8.

RW Set by NWAYEN strapping pin.

See “Strapping Options” section

for details.

0.11 Power Down 1 = Power do wn mode

0 = Normal operation RW 0

0.10 Isolate 1 = Electrical isolation of PHY from MII and

TX+/TX-

0 = Normal operation

RW Set by ISO strapping pin.

See “Strapping Options” section

for details.

0.9 Restart Auto-

Negotiation 1 = Restart auto-negotiation process

0 = Normal operation.

This bit is self-cleared after a ‘1’ is written to it.

RW/SC 0

Micrel, Inc. KSZ8041TL/FTL

April 2007 36 M9999-042707-1.1

Address Name Description Mode(1) Default

0.8 Duplex Mode 1 = Full-duplex

0 = Half-duplex RW Set by DUPLEX strapping pin.

See “Strapping Options” section

for details.

0.7 Collision Test 1 = Enable COL test

0 = Disable COL test RW 0

0.6:1 Reserved RO 000_000

0.0 Disable

Transmitter 0 = Enable transmitter

1 = Disable transmitter RW 0

1.15 100Base-T4 1 = T4 capable

0 = Not T4 capable RO 0

1.14 100Base-TX

Full Duplex 1 = Capable of 100Mbps full-duplex

0 = Not capable of 100Mbps full-duplex RO 1

1.13 100Base-TX

Half Duplex 1 = Capable of 100Mbps half-duplex

0 = Not capable of 100Mbps half-duplex RO 1

1.12 10Base-T Full

Duplex 1 = Capable of 10Mbps full-duplex

0 = Not capable of 10Mbps full-duplex RO 1

1.11 10Base-T Half

Duplex 1 = Capable of 10Mbps half-duplex

0 = Not capable of 10Mbps half-duplex RO 1

1.10:7 Reserved RO 0000

1.6 No Preamble 1 = Preamble s uppression

0 = Normal preamble RO 1

1.5 Auto-

Negotiation

Complete

1 = Auto-negotiation process completed

0 = Auto-negotiation process not completed RO 0

1.4 Remote Fault 1 = Remote fault

0 = No remote fault RO/LH 0

1.3 Auto-

Negotiation

Ability

1 = Capable to perform auto-negoti ation

0 = Not capable to perform auto-negotiation RO 1

1.2 Link Status 1 = Link is up

0 = Link is down RO/LL 0

1.1 Jabber Detect 1 = Jabber detected

0 = Jabber not detected (default is low) RO/LH 0

1.0 Extended

Capability 1 = Supports extended capabi lities registers RO 1

2.15:0 PHY ID

Number Assigned to the 3rd through 18th bits of the

Organizationally Unique Identifier (OUI).

Kendin Communication’s OUI is 0010A1 (hex)

RO 0022h

Micrel, Inc. KSZ8041TL/FTL

April 2007 37 M9999-042707-1.1

Address Name Description Mode(1) Default

3.15:10 PHY ID

Number Assigned to the 19th through 24th bits of the

Organizationally Unique Identifier (OUI).

Kendin Communication’s OUI is 0010A1 (hex)

RO 0001_01

3.9:4 Model Number Six bit manufacturer’s model number RO 01_0001

3.3:0 Revision

Number Four bit manufacturer’s model number RO 0010

4.15 Next Page 1 = Next page capable

0 = No next page capabi lity. RW 0

4.14 Reserved RO 0

4.13 Remote Fault 1 = Remote fault supported

0 = No remote fault RW 0

4.12:11 Reserved RO 00

4.10 Pause 1 = PAUSE function supported

0 = No PAUSE function supported RW 0

4.9 100Base-T4 1 = T4 capable

0 = No T4 capability RO 0

4.8 100Base-TX

Full-Duplex 1 = 100Mbps full-dupl ex capable

0 = No 100Mbps full-duple x capability RW Set by SPEED strapping pin.

See “Strapping Options” section

for details.

4.7 100Base-TX

Half-Duplex 1 = 100Mbps half-duplex capable

0 = No 100Mbps half-duple x capability RW Set by SPEED strapping pin.

See “Strapping Options” section

for details.

4.6 10Base-T

Full-Duplex 1 = 10Mbps full-duplex capable

0 = No 10Mbps full-duplex cap ability RW 1

4.5 10Base-T

Half-Duplex 1 = 10Mbps half-duplex capable

0 = No 10Mbps half-duplex capability RW 1

4.4:0 Selector Field [00001] = IEEE 802.3 RW 0_0001

5.15 Next Page 1 = Next page capable

0 = No next page capability RO 0

5.14 Acknowledge 1 = Link code word received from partner

0 = Link code word not yet received RO 0

5.13 Remote Fault 1 = Remote fault detected

0 = No remote fault RO 0

5.12 Reserved RO 0

5.11:10 Pause [00] = No PAUSE

[10] = Asymmetric PAUSE

[01] = Symmetric PAUSE

[11] = Asymmetric & Symmetric PAUSE

RO 00

Micrel, Inc. KSZ8041TL/FTL

April 2007 38 M9999-042707-1.1

Address Name Description Mode(1) Default

5.9 100Base-T4 1 = T4 capable

0 = No T4 capability RO 0

5.8 100Base-TX

Full-Duplex 1 = 100Mbps full-dupl ex capable

0 = No 100Mbps full-duple x capability RO 0

5.7 100Base-TX

Half-Duplex 1 = 100Mbps half-duplex capable

0 = No 100Mbps half-duple x capability RO 0

5.6 10Base-T

Full-Duplex 1 = 10Mbps full-duplex capable

0 = No 10Mbps full-duplex cap ability RO 0

5.5 10Base-T

Half-Duplex 1 = 10Mbps half-duplex capable

0 = No 10Mbps half-duplex capability RO 0

5.4:0 Selector Field [00001] = IEEE 802.3 RO 0_0001

6.15:5 Reserved RO 0000_0000_000

6.4 Parallel

Detection Fault 1 = Fault detected by parallel detection

0 = No fault detected by parallel detection. RO/LH 0

6.3 Link Partner

Able

1 = Link partner has next page capa bility

0 = Link partner does not have next page

capability

RO 0

6.2 Next Page

Able 1 = Local device has next page capa bility

0 = Local device does not have next page

capability

RO 1

6.1 Page Received 1 = New page received

0 = New page not received yet RO/LH 0

6.0 Link Partner

Auto-

Negotiation

Able

1 = Link partner has auto-negotiation capa bility

0 = Link partner does not have auto-neg otiation

capability

RO 0

7.15 Next Page 1 = Additional next page(s) will follow

0 = Last page RW 0

7.14 Reserved RO 0

7.13 Message Page 1 = Message page

0 = Unformatted page RW 1

7.12 Acknowledge2 1 = Will comply with message

0 = Cannot comply with message RW 0

7.11 Toggle 1 = Previous value of the transmitted link code

word equaled logic one

0 = Logic zero

RO 0

7.10:0 Message Field 11-bit wide field to encode 2048 messages RW 000_0000_0001

8.15 Next Page 1 = Additional Next Page(s) will follow

0 = Last page RO 0

Micrel, Inc. KSZ8041TL/FTL

April 2007 39 M9999-042707-1.1

Address Name Description Mode(1) Default

8.14 Acknowledge 1 = Successful receipt of link word

0 = No successful receipt of link word RO 0

8.13 Message Page 1 = Message page

0 = Unformatted page RO 0

8.12 Acknowledge2 1 = Able to act on the information

0 = Not able to act on the information RO 0

8.11 Toggle 1 = Previous value of transmitted link code

word equal to logic zero

0 = Previous value of transmitted link code

word equal to logic one

RO 0

8.10:0 Message Field RO 000_0000_0000

15.15:0 RXER Counter Receive error counter for Symbol Error frame s RO/SC 0000h

1b.15 Jabber

Interrupt

Enable

1 = Enable Jabber Interrupt

0 = Disable Jabber Interrupt RW 0

1b.14 Receive Error

Interrupt

Enable

1 = Enable Receive Error Interrupt

0 = Disable Receive Error Interrupt RW 0

1b.13 Page Received

Interrupt

Enable

1 = Enable Page Received Interrupt

0 = Disable Page Receive d Interrupt RW 0

1b.12 Parallel Detect

Fault Interrupt

Enable

1 = Enable Parallel Detect Fault Interrupt

0 = Disable Parallel Detect Fault Interrupt RW 0

1b.11 Link Partner

Acknowledge

Interrupt

Enable

1 = Enable Link Partner Acknowledge Interrupt

0 = Disable Link Partner Acknowledge

Interrupt

RW 0

1b.10 Link Down

Interrupt

Enable

1 = Enable Link Down Interrupt

0 = Disable Link Do wn Interrupt RW 0

1b.9 Remote Fault

Interrupt

Enable

1 = Enable Remote Fault Interrupt

0 = Disable Remote Fault Interrupt RW 0

1b.8 Link Up

Interrupt

Enable

1 = Enable Link Up Interrupt

0 = Disable Link Up Interrupt RW 0

1b.7 Jabber

Interrupt 1 = Jabber occurred

0 = Jabber did not occurred RO/SC 0

1b.6 Receive Error

Interrupt 1 = Receive Error occurred

0 = Receive Error did not occurred RO/SC 0

1b.5 Page Receive

Interrupt 1 = Page Receive occurred

0 = Page Receive did not occurred RO/SC 0

1b.4 Parallel Detect

Fault Interrupt 1 = Parallel Detect Fault occurred

0 = Parallel Detect Fault did not occurred RO/SC 0

Micrel, Inc. KSZ8041TL/FTL

April 2007 40 M9999-042707-1.1

Address Name Description Mode(1) Default

1b.3 Link Partner

Acknowledge

Interrupt

1 = Link Partner Acknowledge occurred

0 = Link Partner Acknowledge did not occurred RO/SC 0

1b.2 Link Down

Interrupt 1 = Link Down occurred

0 = Link Down did not occurred RO/SC 0

1b.1 Remote Fault

Interrupt 1 = Remote F ault occurred

0 = Remote Fault did not occurred RO/SC 0

1b.0 Link Up

Interrupt 1 = Link Up occurred

0 = Link Up did not occurred RO/SC 0

1d.15 Cable

Diagnostic

Test Enable

1 = Enable cable diagnostic test. After test

has completed, this bit is self-cleared.

0 = Indicates cable diagnostic test (if enable d)

has completed and the status information

is valid for read.

RW/SC 0

1d.14:13 Cable

Diagnostic

Test Result

[00] = normal condition

[01] = open condition has been detected in

cable

[10] = short condition has been detected in

cable

[11] = cable diagnostic test has failed

RO 00

1d.12:9 Reserved 0000

1d.8:0 Cable Fault

Counter Distance to fault; it’s approximatel y

0.4m*(Cable Fault Counter value in decimal) RO 0_0000_0000

1e.15:14 LED mode [00] = LED1 : Speed

LED0 : Link/Activity

[01] = LED1 : Activity

LED0 : Link

[10] = Reserved

[11] = Reserved

RW 00

1e.13 Polarity 0 = Polarity is not reversed

1 = Polarity is reversed RO

1e.12 Far-End Fault

Detect 0 = Far-End Fault not detected

1 = Far-End Fault detected

This bit applies to KSZ8041FTL fiber on ly.

RO 0

1e.11 MDI/MDI-X

State 0 = MDI

1 = MDI-X RO

1e.10:8 Reserved

1e.7 Remote

loopback 0 = Normal mode

1 = Remote (analog) loop back is enab le RW 0

1e.6:0 Reserved

Micrel, Inc. KSZ8041TL/FTL

April 2007 41 M9999-042707-1.1

Address Name Description Mode(1) Default

1f.15 HP_MDIX 0 = Micrel Auto MDI/MDI-X mode

1 = HP Auto MDI/MDI-X mode RW 1

1f.14 MDI/MDI-X

Select When Auto MDI/MDI-X is disabled,

0 = MDI Mode

Transmit on TX+/- (pins 12,11) and

Receive on RX+/ - (pins 10,9)

1 = MDI-X Mode

Transmit on RX+/- (pins 10,9) and

Receive on TX+/- (pins 12,11)

RW 0

1f.13 Pairswap

Disable 1 = Disable auto MDI/MDI-X

0 = Enable auto MDI/MDI-X RW 0

1f.12 Energy Detect

1 = Presence of signal on RX+/- analo g wire

pair

0 = No signal detected on RX+/ -

RO 0

1f.11 Force Link 1 = Force link pass

0 = Normal link operation

This bit bypasses the control logic and allow

transmitter to send pattern even if there is no

link.

RW 0

1f.10 Power Saving 1 = Enable power saving

0 = Disable power saving

If power saving mode is enabled and the cable

is disconnected, the RXC clock output (in MII

mode) is disabled. RXC clock is enable d afte r

the cable is connected and link is established.

RW 0

1f.9 Interrupt Level 1 = Interrupt pin active high

0 = Interrupt pin active low RW 0

1f.8 Enable Jabber 1 = Enable jabber counter

0 = Disable jabber counter RW 1

1f.7 Auto-

Negotiation

Complete

1 = Auto-negotiation process completed

0 = Auto-negotiation process not completed RO 0

1f.6 Enable Paus e

(Flow Control) 1 = F low control capable

0 = No flow control capabilit y RO 0

1f.5 PHY Isolate 1 = PHY in isolate mode

0 = PHY in normal operation RO 0

1f.4:2 Operation

Mode

Indication

[000] = still in auto-negotiation

[001] = 10Base-T half-duplex

[010] = 100Base-TX half-dupl ex

[011] = reserved

[101] = 10Base-T full-duplex

[110] = 100Base-TX full-duplex

[111] = reserved

RO 000

1f.1 Enable SQE

test 1 = Enable SQE test

0 = Disable SQE test RW 0

Micrel, Inc. KSZ8041TL/FTL

April 2007 42 M9999-042707-1.1

Address Name Description Mode(1) Default

1f.0 Disable Data

Scrambling 1 = Disable scrambler

0 = Enable scrambler RW 0

Note:

1. RW = Read/Write.

RO = Read only.

SC = Self-cleared.

LH = Latch high.

LL = Latch low.

Micrel, Inc. KSZ8041TL/FTL

April 2007 43 M9999-042707-1.1

Absolute Maximum Ratings(1)

Supply Voltage

(VDD_1.8, VDDA_1.8, V1.8_OUT)........................-0.5V to +2.4V

(VDDIO_3.3, VDDA_3.3) ...................................-0.5V to +4.0V

Input Voltage (all inputs) ...............................-0.5V to +4.0V

Output Voltage (all outputs) ..........................-0.5V to +4.0V

Lead Temperature (solderi ng, 10sec. ).......................260°C

Storage Temperature (Ts)..........................-55°C to +150°C

Operating Ratings(2)

Supply Voltage

(VDDIO_3.3, VDDA_3.3) ..........................+3.135V to +3.465V

Ambient Temperature (TA)..............................0°C to +70°C

Maximum Junction Temperature (TJ Max).................125°C

Thermal Resistance (θJA)....................................69.64°C/W

Electrical Characteristics(3)

Symbol Parameter Condition Min Typ Max Units

Supply Current(4)

IDD1 100Base-TX Chip only (no transformer);

Full-duplex traffic @ 100% util ization 53 mA

IDD2 10Base-T Chip only (no transformer);

Full-duplex traffic @ 100% util ization 38 mA

IDD3 Power Saving Mode Ethernet cable disconnected (reg. 1F.10 = 1) 32 mA

IDD4 Power Down Mode Software power down (reg. 0.11 = 1) 4 mA

TTL Inputs

VIH Input High Voltage 2.0 V

VIL Input Low Voltage 0.8 V

IIN Input Current VIN = GND ~ VDDIO -10 10

µA

TTL Outputs

VOH Output High Voltage IOH = -4mA 2.4 V

VOL Output Low Voltage IOL = 4mA 0.4 V

|Ioz| Output Tri-State Leakage 10 µA

100Base-TX Transmit (me asured differentially after 1:1 t ran sformer)

VO Peak Differential Output Voltage 100Ω terminati on across differential output 0.95 1.05 V

VIMB Output Voltage Imbalanc e 100Ω termination across differential output 2 %

tr, tf Rise/Fall Time 3 5 ns

Rise/Fall Time Imbalance 0 0.5

Duty Cycle Distortion ± 0.25

Overshoot 5 %

VSET Refere nce Voltage of ISET 0.65 V

Output Jitter Peak-to-peak 0.7 1.4 ns

10Base-T Transmit (measured differentially after 1:1 transformer)

VP Peak Differential Output Voltage 100Ω termination across differential output 2.2 2.8 V

Jitter Added Peak-to-peak 3.5

tr, tf Rise/Fall Time 25 ns

10Base-T Receive

VSQ Squelch Threshold 5MHz square wave 400 mV

Micrel, Inc. KSZ8041TL/FTL

April 2007 44 M9999-042707-1.1

Notes:

1. Exceeding the absolute maximum rating may damage the device. Stresses greater than the absolute maximum rating may cause permanent

damage to the device. Operation of the device at these or any othe r conditions above those specified in the operating sections of this specification

is not implied. Maximum conditions for extended periods may affect reliability.

2. The device is not guaranteed to function outside its operating rating.

3. TA = 25°C. Specification for packaged product only.

4. Current consumption is for the single 3.3V supply KSZ8041TL/FTL device only, and includes the 1.8V supply voltage (VDD_1.8, VDDA_1.8, V1.8_OUT) that is

provided by the KSZ8041TL/FTL. The PHY port’s transformer consumes an additional 45mA @ 3.3V for 100Base-TX and 70mA @ 3.3V for

10Base-T.

Micrel, Inc. KSZ8041TL/FTL

April 2007 45 M9999-042707-1.1

Timing Diagrams

MII SQE Timing (10Base-T)

TXC

tSQE

COL tSQEP

TXEN

tWL tWH

Figure 11. MII SQE Timing (10Base-T)

Timing Parameter Description Min Typ Max Unit

tP TXC period 400 ns

tWL TXC pulse width low 200 ns

tWH TXC pulse width high 200 ns

tSQE COL (SQE) delay after TXEN de-asserted 2.5 µs

tSQEP COL (SQE) pulse duration 1.0 µs

Table 14. MII SQE Timing (10Base-T) Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 46 M9999-042707-1.1

MII Transmit Timing (10Base-T)

TXC

tHD2

tSU2

TXEN

TXD[3:0] tSU1 tHD1

CRS tCRS2

tCRS1

tWH

tWL

Figure 12. MII Transmit Ti ming (10Base-T)

Timing Parameter Description Min Typ Max Unit

tP TXC period 400 ns

tWL TXC pulse width low 200 ns

tWH TXC pulse width high 200 ns

tSU1 TXD[3:0] setup to rising edge of TXC 10 ns

tSU2 TXEN setup to rising edge of TXC 10 ns

tHD1 TXD[3:0] hold from rising edge of TXC 0 ns

tHD2 TXEN hold from rising edge of TXC 0 ns

tCRS1 TXEN high to CRS asserted l atency 4 Bit

Time

tCRS2 TXEN low to CRS de-asserted latency 8 Bit

Time

Table 15. MII Transmit Timing (10Base-T ) Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 47 M9999-042707-1.1

MII Receive Timing (10Base-T)

Figure 13. MII Receive Timing (10Base-T)

Timing Parameter Description Min Typ Max Unit

tP RXC period 400 ns

tWL RXC pulse width low 200 ns

tWH RXC pulse width high 200 ns

tOD (RXD[3:0], RXER, RXDV) output

delay from rising edge of RXC 182 225 ns

tRLAT CRS to (RXD[3:0], RXER, RXDV)

latency 6.5 µs

Table 16. MII Receive Timing (10Base-T) Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 48 M9999-042707-1.1

MII Transmit Timing (100Base-TX)

Figure 14. MII Transmit Ti ming (100Base-TX)

Timing Parameter Description Min Typ Max Unit

tP TXC period 40 ns

tWL TXC pulse width low 20 ns

tWH TXC pulse width high 20 ns

tSU1 TXD[3:0] setup to rising edge of TXC 10 ns

tSU2 TXEN setup to rising edge of TXC 10 ns

tHD1 TXD[3:0] hold from rising edge of TXC 0 ns

tHD2 TXEN hold from rising edge of TXC 0 ns

tCRS1 TXEN high to CRS asserted l atency 4 Bit

Time

tCRS2 TXEN low to CRS de-asserted latency 4 Bit

Time

Table 17. MII Transmit Timing (100Base-TX) Parameter s

Micrel, Inc. KSZ8041TL/FTL

April 2007 49 M9999-042707-1.1

MII Receive Timing (100Base-TX)

Figure 15. MII Receive Timing (100Base- TX)

Timing Parameter Description Min Typ Max Unit

tP RXC period 40 ns

tWL RXC pulse width low 20 ns

tWH RXC pulse width high 20 ns

tOD (RXD[3:0], RXER, RXDV) output

delay from rising edge of RXC 19 25 ns

tRLAT CRS to (RXD[3:0], RXER, RXDV)

latency 1 2 3

Bit

Time

Table 18. MII Receive Timing (100Base-TX) Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 50 M9999-042707-1.1

RMII Timing

REFCLK

tcyc

TX_EN

TXD[1:0]

Transmit

Timing

Figure 16. RMII Timing – Data Received from RMII

REFCLK

tcyc

tod

CRSDV

RXD[1:0]

Receive

Timing

Figure 17. RMII Timing – Data Input to RMII

Timing Parameter Description Min Typ Max Unit

tcyc Clock cycle 20 ns

t1 Setup time 4 ns

t2 Hold time 2 ns

tod Output delay 2.8 10 ns

Table 19. RMII Timing Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 51 M9999-042707-1.1

Auto-Negotiation Timing

Auto-Negotiation

Fast Link Pulse (FL P) Timin g

tPW

TX+/TX-

Clock

Pulse Data

Pulse Clock

Pulse

tPW

tCTD

tCTC

tFLPW

tBTB

TX+/TX-

Data

Pulse

FLP

Burst FLP

Burst

Figure 18. Auto-Negotiation Fast Link Pulse (FLP) Timing

Timing Parameter Description Min Typ Max Units

tBTB FLP Burst to FLP Burst 8 16 24 ms

tFLPW FLP Burst width 2 ms

tPW Clock/Data Pulse width 100 ns

tCTD Clock Pulse to Data Pulse 55.5 64 69.5 µs

tCTC Clock Pulse to Clock Pulse 111 128 139 µs

Number of Clock/Data Pulse per

FLP Burst 17 33

Table 20. Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 52 M9999-042707-1.1

MDC/MDIO Timing

tMD1

Valid

Data

MDIO

(PHY input) Valid

Data

MDC

tMD2

MDIO

(PHY output) Valid

Data

tMD3

Figure 19. MDC/MDIO Timing

Timing Parameter Description Min Typ Max Unit

tP MDC period 400 ns

t1MD1 MDIO (PHY input) setup to rising edge of MDC 10 ns

tMD2 MDIO (PHY input) hold from rising edge of MDC 10 ns

tMD3 MDIO (PHY output) delay from rising edge of MDC 222 ns

Table 21. MDC/MDIO Timing Parameters

Micrel, Inc. KSZ8041TL/FTL

April 2007 53 M9999-042707-1.1

Reset Timing

The KSZ8041TL/FTL reset timing requirement is summarized in the following figure and table.

tsr

tcs tch

trc

Supply

Voltage

RST#

Strap-In

Value

Strap-In /

Output Pi n

Figure 20. Reset Timing

Parameter Description Min Max Units

tsr Stable supply voltage to reset high 10 ms

tcs Configuration setup time 5 ns

tch Configuration hold time 5 ns

trc Reset to strap-in pin output 6 ns

Table 22. Reset Timing Parameters

After the de-assertion of reset, it is recommended to wait a minimum of 100µs before starting programming on the MIIM

(MDC/MDIO) Interface.

Micrel, Inc. KSZ8041TL/FTL

April 2007 54 M9999-042707-1.1

Reset Circuit

The following reset circuit is recommended for powering up the KSZ8041TL/FTL if reset is triggered by the power supply.

KSZ8041TL/FTL

3.3V

D1: 1N 4148

R 10K

C 10uF

RST#

Figure 21. Recommended Reset Circuit

The following reset circuit is recommended for applications where reset is driven by another device (e.g., CPU or FPGA).

At power-on-reset, R, C and D1 provide the necessary ramp rise time to reset the KSZ8041TL/FTL device. The

RST_OUT_n from CPU/FPGA provides the warm reset after power up.

KSZ8041TL/FTL CPU/FPGA

3.3V

C 10uF

R 10K

RST_OUT_n

D1, D2: 1N4148

RST#

Figure 22. Recommended Reset Circuit for Interfacing with CPU/FPGA Reset Output

Micrel, Inc. KSZ8041TL/FTL

April 2007 55 M9999-042707-1.1

The following figure shows the reference circuits for pull-up, float and pull-down on the LED1 and LED0 strapping pins.

LED pin

3.3V

Pull-up

KSZ8041TL/FTL

3.3V

Float

KSZ8041TL/FTL

LED pin

3.3V

Pull-down

KSZ8041TL/FTL

LED pin

Figure 23. Reference Circuits for LED Strapping Pins

Micrel, Inc. KSZ8041TL/FTL

April 2007 56 M9999-042707-1.1

Selection of Isolation Transformer

A 1:1 isolation transformer is required at the line interface. An isolation transformer with integrated common-mode chokes

is recommended for exceeding FCC requirements.

The following table gives recommen ded transformer characteristics.

Parameter Value Test Condition

Turns ratio 1 CT : 1 CT

Open-circuit inductance (min.) 350µH 100mV, 100kHz, 8mA

Leakage inductance (max.) 0.4µH 1MHz (min.)

Inter-winding capacitance (max.) 12pF

D.C. resistance (max.) 0.9Ω

Insertion loss (max.) 1.0dB 0MHz – 65MH z

HIPOT (min.) 1500Vrms

Table 23. Transformer Selection Criteria

Magnetic Manufacturer Part Number Auto MDI-X Number of Port

Bel Fuse S558-5999-U7 Yes 1

Bel Fuse (Mag Jack) SI-46001 Yes 1

Bel Fuse (Mag Jack) SI-50170 Yes 1

Delta LF8505 Yes 1

LanKom LF-H41S Yes 1

Pulse H1102 Yes 1

Pulse (low cost) H1260 Yes 1

Transpower HB726 Yes 1

TDK (Mag Jack) TLA-6T718 Yes 1

Table 24. Qualified Single Port Magnetics

Selection of Reference Crystal

Characteristics Value Units

Frequency 25 MHz

Frequency tolerance (max) ±50 ppm

Load capacitance (max) 20 pF

Series resistance 40 Ω

Table 25. Typical Reference Crystal Characteristics

Micrel, Inc. KSZ8041TL/FTL

April 2007 57 M9999-042707-1.1

Package Information

,SNOISURTORPROHSALFDLOMEDULCNITONSEODNOISNEMID .MM452.0DEECXETONLLAHSHCIHWFOREHTIE .NOISURTORPRABMADEDU

LCNITONSEODNOISNEMIDDAEL MOTTOBNAHTRELLAMSERASNOISNEMIDDLOMPOTEGAKCAP GNAHREVOTONLLIWEGAKCAPFOPOTDNASNO

ISNEMIDDLOM .EGAKCAPFOMOTTOB

:SETON

.2.3.4

48-Pin (7mm x 7mm) TQFP Package

Note: ALL DIMENSIONS ARE IN MILLIMETERS.

Micrel, Inc. KSZ8041TL/FTL

April 2007 58 M9999-042707-1.1

MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA

TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com

The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its

use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.

Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product

can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical

implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.

A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to

fully indemnify Micrel for any damages resulting from such use or sale.

orated.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Micrel:

KSZ8041FTLI TR KSZ8041FTL TR KSZ8041TL KSZ8041TLI KSZ8041TL-S KSZ8041FTLI KSZ8041TLI-S

KSZ8041FTL KSZ8041TLI TR KSZ8041TL TR KSZ8041FTL-S KSZ8041FTL-EVAL KSZ8041TL-EVAL

KSZ8041FTL-TR KSZ8041FTLI-TR KSZ8041TL-TR KSZ8041TLI-TR